TECHNICAL SUPPORT MANUAL Split System Air Conditioner (C,H,T)4A3

Transcription

1 Split System Air Conditioner (C,H,T)4A3 DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU TION, and NOTE are used to identify levels of hazard seriousness. The signal word DANGER is only used on product labels to signify an immediate hazard. The signal words WARNING, CAUTION, and NOTE will be used on product labels and throughout this manual and other manuals that may apply to the product. DANGER - Immediate hazards which will result in severe personal injury or death. WARNING - Hazards or unsafe practices which could result in severe personal injury or death. CAUTION - Hazards or unsafe practices which may result in minor personal injury or product or property damage. NOTE - Used to highlight suggestions which will result in enhanced installation, reliability, or operation. Safety Labeling and Signal Words Signal Words in Manuals The signal word WARNING is used throughout this manual in the following manner: WARNING! WARNING The signal word CAUTION is used throughout this manual in the following manner:! CAUTION Signal Words on Product Labeling Signal words are used in combination with colors and/or pictures on product labels. TABLE OF CONTENTS Wiring Diagrams Charging Chart Tech Labels (Expanded Data) Condenser Only Data Cooling Multipying Factors Exploded Drawings C4A3 Parts List H4A3 Parts List T4A3 Parts List Number Identification ! WARNING DEATH, PERSONAL INJURY, AND/OR PROPERTY DAMAGE HAZARD Failure to carefully read and follow this warning could result in equipment malfunction, property damage, personal injury and/or death. Installation or repairs made by unqualified persons could result in equipment malfunction, property damage, personal injury and/or death. The information contained in this manual is intended for use by a qualified service technician familiar with safety procedures and equipped with the proper tools and test instruments. Installation must conform with local building codes and with the National Electrical Code NFPA70 current edition or Canadian Electrical Code Part 1 CSA C July 2007

2 Sizes: 18, 24, 30, 36, 42, Symbols are electrical representation only. 2. Compressor and fan motor furnished with inherent thermal protection. 3. To be wired in accordance with National Electric N.E.C. and local codes. 4. N.E.C. class 2, 24 V circuit, min. 40 VA required, 60 VA on units installed with LLS. 5. Use copper conductors only. Use conductors suitable for at least 75 C (167 F). 6. Connection for typical cooling only thermostat. For other arrangements see installation instructions. 7. If indoor section has a transformer with a grounded secondary, connect the grounded side to the BRN/YEL lead. 8. When start capacitor and relay are installed, start thermistor is not used. 9. CH not used on all units. 10. If any of the original wire, as supplied, must be replaced, use the same or equivalent wire. 11. Check all electrical connections inside control box for tightness. 12. Do not attempt to operate unit until service valves have been opened. 13. Do not rapid cycle compressor. Compressor must be off 3 minutes to allow pressures to equalize between high and low side before starting. 14. Wire not present if HPS, LPS or CTD are used. 15. Not for interrupting current. TECHNICAL SUPPORT MANUAL

3 Size: Symbols are electrical representation only. 2. Compressor and fan motor furnished with inherent thermal protection. 3. To be wired in accordance with National Electric N.E.C. and local codes. 4. N.E.C. class 2, 24 V circuit, min. 40 VA required, 60 VA on units installed with LLS. 5. Use copper conductors only. Use conductors suitable for at least 75 C (167 F). 6. Connection for typical cooling only thermostat. For other arrangements see installation instructions. 7. If indoor section has a transformer with a grounded secondary, connect the grounded side to the BRN/YEL lead. 8. When start capacitor and relay are installed, start thermistor is not used. 9. CH not used on all units. 10. If any of the original wire, as supplied, must be replaced, use the same or equivalent wire. 11. Check all electrical connections inside control box for tightness. 12. Do not attempt to operate unit until service valves have been opened. 13. Do not rapid cycle compressor. Compressor must be off 3 minutes to allow pressures to equalize between high and low side before starting. 14. Wire not present if HPS, LPS or CTD are used. 15. Not for interrupting current. TECHNICAL SUPPORT MANUAL

4 R-410A CHARGING CHART Find the required Subcooling Temperature on the unit Rating Plate. Use the closest column on the chart below (6, 8, 10, 12, 14 or 16). Add or remove refrigerant until both the Liquid Line Temperature and Liquid Pressure agree with chart data. Measured Liquid Pressure (psig) Rating Plate (required) Subcooling Temperature ( F) Required Liquid Line Temperature ( F)

5 Total capacities are net (I.D. blower heat subtracted) system capacities based on 25' line set. If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. At TVA rating indoor condition (75 F db, 63 F wb), all other indoor air temperatures are at 80 F db If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ^ System amps are total of indoor and outdoor amps. Chart data is for 80 F indoor dry bulb. For indoor db temperatures other than 80 F, measure db and CFM, and plug these into the formula below. Measure outdoor db and indoor wet bulb, apply these to the chart above, find MBh and S/T, and plug these into the formula below. (Note: if indoor db is the only thing changing, total capacity, MBh, stays the same.) ( ) Sensible Capacity at db LOWER than 80 F = ( MBh x S/T ) - ( 80 - db ) x 835 x CFM 1000 ( ) ( db - 80 ) x 835 x CFM Sensible Capacity at db HIGHER than 80 F = ( MBh x S/T ) TECHNICAL SUPPORT MANUAL

6 Total capacities are net (I.D. blower heat subtracted) system capacities based on 25' line set. If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. At TVA rating indoor condition (75 F db, 63 F wb), all other indoor air temperatures are at 80 F db If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ^ System amps are total of indoor and outdoor amps. Chart data is for 80 F indoor dry bulb. For indoor db temperatures other than 80 F, measure db and CFM, and plug these into the formula below. Measure outdoor db and indoor wet bulb, apply these to the chart above, find MBh and S/T, and plug these into the formula below. (Note: if indoor db is the only thing changing, total capacity, MBh, stays the same.) ( ) Sensible Capacity at db LOWER than 80 F = ( MBh x S/T ) - ( 80 - db ) x 835 x CFM 1000 ( ) ( db - 80 ) x 835 x CFM Sensible Capacity at db HIGHER than 80 F = ( MBh x S/T ) TECHNICAL SUPPORT MANUAL

7 Total capacities are net (I.D. blower heat subtracted) system capacities based on 25' line set. If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. At TVA rating indoor condition (75 F db, 63 F wb), all other indoor air temperatures are at 80 F db If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ^ System amps are total of indoor and outdoor amps. Chart data is for 80 F indoor dry bulb. For indoor db temperatures other than 80 F, measure db and CFM, and plug these into the formula below. Measure outdoor db and indoor wet bulb, apply these to the chart above, find MBh and S/T, and plug these into the formula below. (Note: if indoor db is the only thing changing, total capacity, MBh, stays the same.) ( ) Sensible Capacity at db LOWER than 80 F = ( MBh x S/T ) - ( 80 - db ) x 835 x CFM 1000 ( ) ( db - 80 ) x 835 x CFM Sensible Capacity at db HIGHER than 80 F = ( MBh x S/T ) TECHNICAL SUPPORT MANUAL

8 Total capacities are net (I.D. blower heat subtracted) system capacities based on 25' line set. If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. At TVA rating indoor condition (75 F db, 63 F wb), all other indoor air temperatures are at 80 F db If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ^ System amps are total of indoor and outdoor amps. Chart data is for 80 F indoor dry bulb. For indoor db temperatures other than 80 F, measure db and CFM, and plug these into the formula below. Measure outdoor db and indoor wet bulb, apply these to the chart above, find MBh and S/T, and plug these into the formula below. (Note: if indoor db is the only thing changing, total capacity, MBh, stays the same.) ( ) Sensible Capacity at db LOWER than 80 F = ( MBh x S/T ) - ( 80 - db ) x 835 x CFM 1000 ( ) ( db - 80 ) x 835 x CFM Sensible Capacity at db HIGHER than 80 F = ( MBh x S/T ) TECHNICAL SUPPORT MANUAL

9 Total capacities are net (I.D. blower heat subtracted) system capacities based on 25' line set. If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. At TVA rating indoor condition (75 F db, 63 F wb), all other indoor air temperatures are at 80 F db If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ^ System amps are total of indoor and outdoor amps. Chart data is for 80 F indoor dry bulb. For indoor db temperatures other than 80 F, measure db and CFM, and plug these into the formula below. Measure outdoor db and indoor wet bulb, apply these to the chart above, find MBh and S/T, and plug these into the formula below. (Note: if indoor db is the only thing changing, total capacity, MBh, stays the same.) ( ) Sensible Capacity at db LOWER than 80 F = ( MBh x S/T ) - ( 80 - db ) x 835 x CFM 1000 ( ) ( db - 80 ) x 835 x CFM Sensible Capacity at db HIGHER than 80 F = ( MBh x S/T ) TECHNICAL SUPPORT MANUAL

10 Total capacities are net (I.D. blower heat subtracted) system capacities based on 25' line set. If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. At TVA rating indoor condition (75 F db, 63 F wb), all other indoor air temperatures are at 80 F db If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ^ System amps are total of indoor and outdoor amps. Chart data is for 80 F indoor dry bulb. For indoor db temperatures other than 80 F, measure db and CFM, and plug these into the formula below. Measure outdoor db and indoor wet bulb, apply these to the chart above, find MBh and S/T, and plug these into the formula below. (Note: if indoor db is the only thing changing, total capacity, MBh, stays the same.) ( ) Sensible Capacity at db LOWER than 80 F = ( MBh x S/T ) - ( 80 - db ) x 835 x CFM 1000 ( ) ( db - 80 ) x 835 x CFM Sensible Capacity at db HIGHER than 80 F = ( MBh x S/T ) TECHNICAL SUPPORT MANUAL

11 Total capacities are net (I.D. blower heat subtracted) system capacities based on 25' line set. If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. At TVA rating indoor condition (75 F db, 63 F wb), all other indoor air temperatures are at 80 F db If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ^ System amps are total of indoor and outdoor amps. Chart data is for 80 F indoor dry bulb. For indoor db temperatures other than 80 F, measure db and CFM, and plug these into the formula below. Measure outdoor db and indoor wet bulb, apply these to the chart above, find MBh and S/T, and plug these into the formula below. (Note: if indoor db is the only thing changing, total capacity, MBh, stays the same.) ( ) Sensible Capacity at db LOWER than 80 F = ( MBh x S/T ) - ( 80 - db ) x 835 x CFM 1000 ( ) ( db - 80 ) x 835 x CFM Sensible Capacity at db HIGHER than 80 F = ( MBh x S/T ) TECHNICAL SUPPORT MANUAL

12 Data for Condenser Only (Cooling) Saturated Suction Temperature F Condenser Entering Air Temperature F (C,H,T)4A318 TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW (C,H,T)4A324 TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG = Gross Cooling Capacity (x 1000 BTU/hr) SDT = Saturated Temperature Leaving Compressor kw = Outdoor Unit Kilowatts

13 Data for Condenser Only (Cooling) Saturated Suction Temperature F Condenser Entering Air Temperature F (C,H,T)4A330 TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW (C,H,T)4A336 TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG = Gross Cooling Capacity (x 1000 BTU/hr) SDT = Saturated Temperature Leaving Compressor kw = Outdoor Unit Kilowatts

14 Data for Condenser Only (Cooling) Saturated Suction Temperature F Condenser Entering Air Temperature F (C,H,T)4A342 TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW (C,H,T)4A348 TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG = Gross Cooling Capacity (x 1000 BTU/hr) SDT = Saturated Temperature Leaving Compressor kw = Outdoor Unit Kilowatts

15 Data for Condenser Only (Cooling) Saturated Suction Temperature F Condenser Entering Air Temperature F (C,H,T)4A360 TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG SDT KW TCG = Gross Cooling Capacity (x 1000 BTU/hr) SDT = Saturated Temperature Leaving Compressor kw = Outdoor Unit Kilowatts

16 COOLING Multiplying Factors for other Combinations (C,H,T)4A318 >ED*4X18B** EL*24B**** FS(M,U)4X18*** ED*4X18B** MV08B15**** EL*24B**** MV08B15**** FS(M,U)4X24*** ED*4X24B** EMH24F**** FEM4X18**** ED*4X24B** MV08B15**** EP*18B**** FEM4X24**** ED*4X24F** EP*24B**** EBP18**** ED*4X24F** MV12F19**** EP*24B**** MV08B15**** EBP24**** EMA4X24D** EP*24F**** FWM18**** EHD4X24A** EP*24F**** MV12F19**** FWM24**** EHD4X24A** *9MPV EPP024**** EBXX18**** EHD4X24A** *9MPV EXX*24B**** EBXX24**** EHD4X24A** MV08B15**** EXX*24B**** MV08B15**** EBV24**** EHD4X24A** MV12F19**** EXX*24F**** FVM4X24**** EL*18B**** EXX*24F**** MV12F19**** (C,H,T)4A324 >ED*4X24B** EHD4X24A** *9MPV EP*24B**** MV08B15**** EBP24**** EHD4X24A** *9MPV EP*24F**** EBP30**** EHD4X24A** *9MPV EP*24F**** *9MPV EBV24**** EHD4X24A** *9MPV EP*24F**** *9MPV EBV36**** EHD4X24A** MV08B15**** EP*24F**** MV12F19**** EBXX18**** EHD4X24A** MV12F19**** EP*30B**** EBXX24**** EHD4X24A** MV16J22**** EP*30B**** *8MPV ED*4X24B** *8MPV EHD4X24A** MV20N26**** EP*30B**** MV08B15**** ED*4X24B** MV08B15**** EHD4X30A** EP*30F**** ED*4X24B** *8MPV EHD4X30A** *8MPV EP*30F**** *9MPV ED*4X24B** *9MPV EHD4X30A** *8MPV EP*30F**** *9MPV ED*4X24B** *9MPV EHD4X30A** *8MPV EP*30F**** MV12F19**** ED*4X24F** EHD4X30A** *8MPV EPP024**** ED*4X24F** *8MPV EHD4X30A** *9MPV EPP030**** > Indicates Tested - continued on next page - TECHNICAL SUPPORT MANUAL

17 COOLING Multiplying Factors for other Combinations (continued) ED*4X24F** *9MPV EHD4X30A** *9MPV EXX*24B**** ED*4X24F** *9MPV EHD4X30A** *9MPV EXX*24B**** *8MPV ED*4X24F** MV12F19**** EHD4X30A** MV08B15**** EXX*24B**** MV08B15**** ED*4X30B** EHD4X30A** MV12F19**** EXX*24F**** ED*4X30B** *8MPV EHD4X30A** MV16J22**** EXX*24F**** *8MPV ED*4X30B** MV08B15**** EHD4X30A** MV20N26**** EXX*24F**** *9MPV ED*4X30B** *9MPV EL*24B**** EXX*24F**** *9MPV ED*4X30B** *9MPV EL*24B**** *8MPV EXX*24F**** MV12F19**** ED*4X30F** EL*24B**** MV08B15**** FEM4X24**** ED*4X30F** *9MPV EL*30B**** FEM4X30**** ED*4X30F** *9MPV EL*30B**** *8MPV FS(M,U)4X24*** ED*4X30F** MV12F19**** EL*30B**** MV08B15**** FS(M,U)4X30*** EHD4X24A** EMA4X24D** FSA2X24**** EHD4X24A** *8MPV EMH24F**** FVM4X24**** EHD4X24A** *8MPV EMH30F**** FVM4X36**** EHD4X24A** *8MPV EP*24B**** FWM24**** EHD4X24A** *8MPV EP*24B**** *8MPV FWM30**** (C,H,T)4A330 >ED*4X30B** EHD4X30A** MV12F19**** EP*36B**** *8MPV EBP30**** EHD4X30A** MV16J22**** EP*36B**** MV08B15**** EBP36**** EHD4X30A** MV20N26**** EP*36F**** EBV24**** EHD4X36A** EP*36F**** *8MPV EBV36**** EHD4X36A** *8MPV EP*36F**** *9MPV EBV48**** EHD4X36A** *8MPV EP*36F**** *9MPV EBXX36**** EHD4X36A** *8MPV EP*36F**** MV12F19**** ED*4X30B** *8MPV EHD4X36A** *8MPV EP*36J**** ED*4X30B** MV08B15**** EHD4X36A** *9MPV EP*36J**** *8MPV ED*4X30B** *8MPV EHD4X36A** *9MPV EP*36J**** *8MPV ED*4X30F** EHD4X36A** *9MPV EP*36J**** *9MPV > Indicates Tested - continued on next page - TECHNICAL SUPPORT MANUAL

18 COOLING Multiplying Factors for other Combinations (continued) ED*4X30F** *8MPV EHD4X36A** *9MPV EP*36J**** MV16J22**** ED*4X30F** *9MPV EHD4X36A** MV08B15**** EPP030**** ED*4X30F** *9MPV EHD4X36A** MV12F19**** EPP036**** ED*4X30F** MV12F19**** EHD4X36A** MV16J22**** EXX*36B**** ED*4X36B** EHD4X36A** MV20N26**** EXX*36B**** *8MPV ED*4X36B** *8MPV EL*30B**** EXX*36B**** MV08B15**** ED*4X36B** MV08B15**** EL*30B**** *8MPV EXX*36F**** ED*4X36B** *8MPV EL*30B**** MV08B15**** EXX*36F**** *8MPV ED*4X36F** EL*36B**** EXX*36F**** *9MPV ED*4X36F** *8MPV EL*36B**** *8MPV EXX*36F**** *9MPV ED*4X36F** *9MPV EL*36B**** MV08B15**** EXX*36F**** MV12F19**** ED*4X36F** *9MPV EL*36F**** EXX*36J**** ED*4X36F** MV12F19**** EL*36F**** *8MPV EXX*36J**** *8MPV ED*4X36J** EL*36F**** *9MPV EXX*36J**** *8MPV ED*4X36J** *8MPV EL*36F**** *9MPV EXX*36J**** *9MPV ED*4X36J** *8MPV EL*36F**** MV12F19**** EXX*36J**** MV16J22**** ED*4X36J** *9MPV EMA4X36D** FEM4X30**** ED*4X36J** MV16J22**** EMH30F**** FEM4X36**** EHD4X30A** EMH36F**** FS(M,U)4X30*** EHD4X30A** *8MPV EP*30B**** FSA2X30**** EHD4X30A** *8MPV EP*30B**** *8MPV FSA2X36**** EHD4X30A** *8MPV EP*30B**** MV08B15**** FSU4X36**** EHD4X30A** *8MPV EP*30F**** FVM4X24**** EHD4X30A** *9MPV EP*30F**** *8MPV FVM4X36**** EHD4X30A** *9MPV EP*30F**** *9MPV FVM4X48**** EHD4X30A** *9MPV EP*30F**** *9MPV FWM30**** EHD4X30A** *9MPV EP*30F**** MV12F19**** EHD4X30A** MV08B15**** EP*36B**** > Indicates Tested - continued on next page - TECHNICAL SUPPORT MANUAL

19 COOLING Multiplying Factors for other Combinations (continued) (C,H,T)4A336 >ED*4X36F** EHD4X36A** MV16J22**** EP*42F**** *9MPV EBP36**** EHD4X36A** MV20N26**** EP*42F**** MV12F19**** EBP42**** EHD4X42A** EP*42J**** EBV36**** EHD4X42A** *8MPV EP*42J**** *8MPV EBV48**** EHD4X42A** *8MPV EP*42J**** *8MPV EBXX36**** EHD4X42A** *8MPV EP*42J**** *9MPV ED*4X36B** EHD4X42A** *8MPV EP*42J**** MV16J22**** ED*4X36B** MV08B15**** EHD4X42A** *9MPV EXX*36B**** ED*4X36F** *8MPV EHD4X42A** *9MPV EXX*36B**** *8MPV ED*4X36F** *9MPV EHD4X42A** *9MPV EXX*36B**** MV08B15**** ED*4X36F** *9MPV EHD4X42A** *9MPV EXX*36F**** ED*4X36F** MV12F19**** EHD4X42A** MV08B15**** EXX*36F**** *8MPV ED*4X36J** EHD4X42A** MV12F19**** EXX*36F**** *9MPV ED*4X36J** *8MPV EHD4X42A** MV16J22**** EXX*36F**** *9MPV ED*4X36J** *8MPV EHD4X42A** MV20N26**** EXX*36F**** MV12F19**** ED*4X36J** *9MPV EL*36B**** EXX*36J**** ED*4X36J** MV16J22**** EL*36B**** MV08B15**** EXX*36J**** *8MPV ED*4X42F** EL*36F**** EXX*36J**** *8MPV ED*4X42F** *8MPV EL*36F**** *8MPV EXX*36J**** *9MPV ED*4X42F** *9MPV EL*36F**** *9MPV EXX*36J**** MV16J22**** ED*4X42F** *9MPV EL*36F**** MV12F19**** EXX*42F**** ED*4X42F** MV12F19**** EL*42F**** EXX*42F**** *8MPV ED*4X42J** EL*42F**** *8MPV EXX*42F**** *9MPV ED*4X42J** *8MPV EL*42F**** *9MPV EXX*42F**** *9MPV ED*4X42J** *8MPV EL*42F**** MV12F19**** EXX*42F**** MV12F19**** ED*4X42J** *9MPV EMH36F**** EXX*42J**** ED*4X42J** MV16J22**** EMH42F**** EXX*42J**** *8MPV ED*4X42L** EP*36B**** EXX*42J**** *8MPV > Indicates Tested - continued on next page - TECHNICAL SUPPORT MANUAL

20 COOLING Multiplying Factors for other Combinations (continued) ED*4X42L** *9MPV EP*36B**** MV08B15**** EXX*42J**** *9MPV EMA4X36D** EP*36F**** EXX*42J**** MV16J22**** EHD4X36A** EP*36F**** *8MPV FEM4X36**** EHD4X36A** *8MPV EP*36F**** *9MPV FEM4X36**** EHD4X36A** *8MPV EP*36F**** MV12F19**** FEM4X42**** EHD4X36A** *8MPV EP*36J**** FEM4X42**** EHD4X36A** *8MPV EP*36J**** *8MPV FS(M,U)4X42*** EHD4X36A** *9MPV EP*36J**** *8MPV FSA2X36**** EHD4X36A** *9MPV EP*36J**** *9MPV FSM4X36**** EHD4X36A** *9MPV EP*36J**** MV16J22**** FSU4X36**** EHD4X36A** *9MPV EP*42F**** FVM4X36**** EHD4X36A** MV08B15**** EP*42F**** *8MPV FVM4X48**** EHD4X36A** MV12F19**** EP*42F**** *9MPV (C,H,T)4A342 >ED*4X42J** EHD4X42A** MV20N26**** EP*48J**** *8MPV EBP42**** EHD4X48A** EP*48J**** *9MPV EBP48**** EHD4X48A** *8MPV EP*48J**** MV16J22**** EBV48**** EHD4X48A** *8MPV EP*48L**** EBV60**** EHD4X48A** *8MPV EP*48L**** *9MPV EBXX48**** EHD4X48A** *9MPV EP*48N**** ED*4X42F** EHD4X48A** *9MPV EP*48N**** MV20N26**** ED*4X42F** *8MPV EHD4X48A** MV16J22**** EXX*42F**** ED*4X42F** *9MPV EHD4X48A** MV20N26**** EXX*42F**** *8MPV ED*4X42J** *8MPV EL*42F**** EXX*42F**** *9MPV ED*4X42J** *8MPV EL*42F**** *8MPV EXX*42J**** ED*4X42J** *9MPV EL*42F**** *9MPV EXX*42J**** *8MPV ED*4X42J** MV16J22**** EL*48F**** EXX*42J**** *8MPV ED*4X42L** EL*48F**** *8MPV EXX*42J**** *9MPV ED*4X42L** *9MPV EL*48F**** *9MPV EXX*42J**** MV16J22**** > Indicates Tested - continued on next page - TECHNICAL SUPPORT MANUAL

21 COOLING Multiplying Factors for other Combinations (continued) ED*4X48F** EMA4X48D** EXX*48J**** ED*4X48F** *8MPV EMH42F**** EXX*48J**** *9MPV ED*4X48J** EMH48F**** EXX*48L**** ED*4X48J** *8MPV EP*42F**** EXX*48L**** *9MPV ED*4X48J** *8MPV EP*42F**** *8MPV EXX*48N**** ED*4X48J** *9MPV EP*42F**** *9MPV EXX*48N**** MV20N26**** ED*4X48J** MV16J22**** EP*42J**** FEM4X42**** ED*4X48L** EP*42J**** *8MPV FEM4X42**** ED*4X48L** *9MPV EP*42J**** *8MPV FEM4X48**** EHD4X42A** EP*42J**** *9MPV FEM4X48**** EHD4X42A** *8MPV EP*42J**** MV16J22**** FS(M,U)4X42*** EHD4X42A** *8MPV EP*48F**** FS(M,U)4X48*** EHD4X42A** *8MPV EP*48F**** *8MPV FSM4X36**** EHD4X42A** *9MPV EP*48F**** *9MPV FVM4X48**** EHD4X42A** *9MPV EP*48J**** FVM4X60**** EHD4X42A** MV16J22**** EP*48J**** *8MPV (C,H,T)4A348 >ED*4X48J** EHD4X60A** EP*60J**** *8MPV EBP48**** EHD4X60A** *8MPV EP*60J**** *8MPV EBP60**** EHD4X60A** *8MPV EP*60J**** *9MPV EBV48**** EHD4X60A** *9MPV EP*60J**** MV16J22**** EBV60**** EHD4X60A** MV16J22**** EP*60L**** EBXX48**** EHD4X60A** MV20N26**** EP*60L**** *9MPV EBXX60**** EL*48F**** EP*60N**** ED*4X48F** EL*60J**** EP*60N**** MV20N26**** ED*4X48J** *8MPV EL*60J**** *8MPV EXX*48J**** ED*4X48J** MV16J22**** EL*60J**** *8MPV EXX*48J**** *9MPV ED*4X48L** EL*60J**** *9MPV EXX*48L**** ED*4X48L** *9MPV EL*60J**** MV16J22**** EXX*48L**** *9MPV > Indicates Tested - continued on next page - TECHNICAL SUPPORT MANUAL

22 COOLING Multiplying Factors for other Combinations (continued) ED*4X60J** EMA4X48D** EXX*48N**** ED*4X60J** *8MPV EMH48F**** EXX*48N**** MV20N26**** ED*4X60J** *8MPV EP*48F**** EXX*60L**** ED*4X60J** *9MPV EP*48J**** EXX*60L**** *9MPV ED*4X60J** MV16J22**** EP*48J**** *8MPV EXX*60N**** ED*4X60L** EP*48J**** *8MPV EXX*60N**** MV20N26**** ED*4X60L** *9MPV EP*48J**** *9MPV FEM4X48**** EHD4X48A** EP*48J**** MV16J22**** FEM4X60**** EHD4X48A** *8MPV EP*48L**** FS(M,U)4X48*** EHD4X48A** *8MPV EP*48L**** *9MPV FS(M,U)4X60*** EHD4X48A** *9MPV EP*48N**** FVM4X48**** EHD4X48A** MV16J22**** EP*48N**** MV20N26**** FVM4X60**** EHD4X48A** MV20N26**** EP*60J**** (C,H,T)4A360 >ED*4X60L** EHD4X60A** MV20N26**** EP*60L**** *9MPV EBP60**** EL*60J**** EP*60N**** EBV60**** EL*60J**** *8MPV EP*60N**** MV20N26**** EBXX60**** EL*60J**** *8MPV EXX*60L**** ED*4X60J** EL*60J**** *9MPV EXX*60L**** *9MPV ED*4X60J** *8MPV EL*60J**** MV16J22**** EXX*60N**** ED*4X60J** MV16J22**** EP*60J**** EXX*60N**** MV20N26**** ED*4X60L** *9MPV EP*60J**** *8MPV FEM4X60**** EHD4X60A** EP*60J**** *8MPV FS(M,U)4X60*** EHD4X60A** *8MPV EP*60J**** *9MPV FVM4X60**** EHD4X60A** *9MPV EP*60J**** MV16J22**** EHD4X60A** MV16J22**** EP*60L**** > Indicates Tested TECHNICAL SUPPORT MANUAL

23 NOTE: This illustration is for reference only. Your unit may differ in appearance or may not include all components shown. Please refer to Parts List for exact parts listing. Motor, Cap R B Nut Fan,Guard L Top, Cover A Motor, Fan 2 32 Raceway 3 Fan Grille, Inlet C3 H Access, Panel Control, Box Cover E Grille,Inlet C2 Corner, Post Assembly J K D Control, Box F Service Panel C1 Grille, Inlet Plate,Filler Kick,Plate S G Base, Pan

24 NOTE: This illustration is for reference only. Your unit may differ in appearance or may not include all components shown. Please refer to Parts List for exact parts listing. 6 Condenser, Coil Assembly 27 Blanket,Sound ( When Used ) 1 Compressor Plug, Compressor 9 11 Bolt, SHLDR (4) Switch, High Pressure Heater, CRKC ( When Used ) Switch, Low Pressure Valve Service, Liquid Valve Service Suction Grommet Compressor, N Support Coil Filter Drier G Base Pan Switch Temp. CC Heater (When Used),

25 NOTE: This illustration is for reference only. Your unit may differ in appearance or may not include all components shown. Please refer to Parts List for exact parts listing. Module, Compressor Diagnostics 25 D Box, Control CTL, 2 SPD Fan 21 Capacitor 5 P Strap, Capacitor Contactor 4 33 Lug, Ground 34 Harness Assembly

26 C4A3 PARTS LIST C4A318GKA100 C4A324GKA100 C4A330GKA100 C4A336GKA100 C4A342GKA100 C4A348GKA100 C4A360GKA100 KEY NO. DESCRIPTION PART NO. 1 Compressor ZP16K5EPFV ZP21K5EPFV ZP25K5EPFV ZP31K5EPFV ZP38K5EPFV ZP42K5EPFV ZP54K5EPFV Motor, Condenser Fan Fan Blade Contactor, 30 Amp Amp Capacitor, 370V 30+5 Mfd V 40+5 Mfd V 45+5 Mfd V Mfd V Mfd Condenser Coil Service Valve, Suction Service Valve, Liquid Plug, Compressor Harness Isolator, Vibration Grommet, Compressor continued on next page

27 KEY NO. DESCRIPTION C4A3 PARTS LIST PART NO. C4A330GKA100 C4A336GKA100 C4A342GKA100 C4A348GKA100 C4A360GKA Nut, Hex Washer Face 5/ Bolt, Compressor Mounting Switch, Low Pressure Switch, High Pressure Control, 2 Speed Fan Drier Module, Comfort Alert Blanket, Compressor Sound Raceway Lug, Ground Harness Assy Plug and Play A Panel, Top A B Nut, Hex C1 Grille, Inlet C C C C C2 Grille, Inlet C C C C C3 Grille, Inlet C C C C C4 Grille, Inlet C D Box, Control E Cover, Control Box continued on next page C4A318GKA100 C4A324GKA100

28 KEY NO. DESCRIPTION C4A3 PARTS LIST PART NO. C4A318GKA100 C4A324GKA100 C4A330GKA100 C4A336GKA100 C4A342GKA100 C4A348GKA100 C4A360GKA100 F Panel, Service F F F G Pan, Base G H Panel, Access H H H1 Panel, Access H H2 Panel, Access H J Post, Corner J J J K Plate, Filler K1 Plate, Filler K2 Plate, Filler L Guard, Fan L N Support, Coil P Strap, Capacitor P R Cap Assy Comfortmaker )( Manual, Installation )( Manual, Owners )( Warranty

29 H4A3 PARTS LIST H4A318GKA100 H4A324GKA100 H4A330GKA100 H4A336GKA100 H4A342GKA100 H4A348GKA100 H4A360GKA100 KEY NO. DESCRIPTION PART NO. 1 Compressor ZP16K5EPFV ZP21K5EPFV ZP25K5EPFV ZP31K5EPFV ZP38K5EPFV ZP42K5EPFV ZP54K5EPFV Motor, Condenser Fan Fan Blade Contactor, 30 Amp Amp Capacitor, 370V 30+5 Mfd V 40+5 Mfd V 45+5 Mfd V Mfd V Mfd Condenser Coil Service Valve, Suction Service Valve, Liquid Plug, Compressor Harness Isolator, Vibration Grommet, Compressor continued on next page

30 KEY NO. DESCRIPTION H4A3 PARTS LIST PART NO. H4A318GKA100 H4A324GKA100 H4A330GKA100 H4A336GKA100 H4A342GKA100 H4A348GKA100 H4A360GKA Nut, Hex Washer Face 5/ Bolt, Compressor Mounting Switch, Low Pressure Switch, High Pressure Control, 2 Speed Fan Drier Module, Comfort Alert Blanket, Compressor Sound Raceway Lug, Ground Harness Assy Plug and Play A Panel, Top A B Nut, Hex C1 Grille, Inlet C C C C C2 Grille, Inlet C C C C C3 Grille, Inlet C C C C C4 Grille, Inlet C D Box, Control E Cover, Control Box continued on next page

31 KEY NO. DESCRIPTION H4A3 PARTS LIST PART NO. H4A318GKA100 H4A324GKA100 H4A330GKA100 H4A336GKA100 H4A342GKA100 H4A348GKA100 H4A360GKA100 F Panel, Service F F F G Pan, Base G H Panel, Access H H H1 Panel, Access H H2 Panel, Access H J Post, Corner J J J K Plate, Filler K1 Plate, Filler K2 Plate, Filler L Guard, Fan L N Support, Coil P Strap, Capacitor P R Cap Assy Heil )( Manual, Installation )( Manual, Owners )( Warranty

32 T4A3 PARTS LIST T4A318GKA100 T4A324GKA100 T4A330GKA100 T4A336GKA100 T4A342GKA100 T4A348GKA100 T4A360GKA100 KEY NO. DESCRIPTION PART NO. 1 Compressor ZP16K5EPFV ZP21K5EPFV ZP25K5EPFV ZP31K5EPFV ZP38K5EPFV ZP42K5EPFV ZP54K5EPFV Motor, Condenser Fan Fan Blade Contactor, 30 Amp Amp Capacitor, 370V 30+5 Mfd V 40+5 Mfd V 45+5 Mfd V Mfd V Mfd Condenser Coil Service Valve, Suction Service Valve, Liquid Plug, Compressor Harness Isolator, Vibration Grommet, Compressor continued on next page

33 KEY NO. DESCRIPTION T4A3 PARTS LIST PART NO. T4A330GKA100 T4A336GKA100 T4A342GKA100 T4A348GKA100 T4A360GKA Nut, Hex Washer Face 5/ Bolt, Compressor Mounting Switch, Low Pressure Switch, High Pressure Control, 2 Speed Fan Drier Module, Comfort Alert Blanket, Compressor Sound Raceway Lug, Ground Harness Assy Plug and Play A Panel, Top A B Nut, Hex C1 Grille, Inlet C C C C C2 Grille, Inlet C C C C C3 Grille, Inlet C C C C C4 Grille, Inlet C D Box, Control E Cover, Control Box continued on next page T4A318GKA100 T4A324GKA100

34 KEY NO. DESCRIPTION T4A3 PARTS LIST PART NO. T4A318GKA100 T4A324GKA100 T4A330GKA100 T4A336GKA100 T4A342GKA100 T4A348GKA100 T4A360GKA100 F Panel, Service F F F G Pan, Base G H Panel, Access H H H1 Panel, Access H H2 Panel, Access H J Post, Corner J J J K Plate, Filler K1 Plate, Filler K2 Plate, Filler L Guard, Fan L N Support, Coil P Strap, Capacitor P R Cap Assy Heil )( Manual, Installation )( Manual, Owners )( Warranty