Installation Instructions Electric Heaters 5 20 kw
|
|
- Ariel Hamilton
- 5 years ago
- Views:
Transcription
1 Small Packaged Products 2 to 5 Tons Accessory Electric Heaters Cancels: IIK 564A-24-2 IIK 564A Installation Instructions Electric Heaters 5 20 kw NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment can be hazardous due to system pressures, electrical components, and fuel gases. Only trained and qualified personnel should install, service, or repair air conditioning equipment. Untrained personnel can perform basic maintenance functions such as cleaning coils, or cleaning and replacing filters. All other operations should be performed by trained service personnel. When working on air conditioning equipment, observe precautions in the literature, on tags, and on labels attached to the unit. Recognize safety information. This is the safety-alert symbol. When you see this symbol on the unit and in instructions or manuals, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING, and CAU- TION. These words are used with the safety-alert symbol. DAN- GER identifies the most serious hazards which will result in serious injury or death. WARNING signifies a hazard which could result in serious injury or death. CAUTION is used to identify unsafe practices which would result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation. Follow all safety codes. Wear safety glasses and work gloves. Have a fire extinguisher available. Before proceeding with heater installation, inspect thoroughly for shipping damage. Notify shipper immediately if any damage is found. Clean all dirt, dust and moisture from heater package. Check for proper clearances of live parts, between phases and to ground. Make sure that all required barriers are in place. Check conductors run in multiple to insure that they are properly wired. Refer to unit installation instructions for complete unit installation details. The minimum air quantity for safe electric heater operation is shown in Table 2. Before performing installation, service or maintenance operations on this system turn off all main power switches and/or disconnects. There may be more than one switch or disconnect. Turn off accessory heater power switch if applicable. Electrical shock can cause serious injury or death. TAG DISCONNECT SWITCH(S) WITH A SUITABLE WARNING LABEL. INTRODUCTION This electric heater series is engineered, designed and listed to be installed only in the models shown in Table. Before proceeding, verify the heater label for correct voltage and kw requirements. DESCRIPTION AND USAGE These SPP Electric heaters are to be used per Table in SPP Electric Cooling & Electric Heat Pump units. Table Electric Heater Usage Chart UNIT SIZE 50ZP/564A/PAZ ZH/664A/PHZ INSTALLATION HEATER INSTALLATION NOTE: Thermostat used must be capable of energizing G (Indoor Fan) on a call for W (Heating). If G is not energized system malfunction will occur.. Open all electrical disconnects and install lock-out tag before beginning any installation or service work. 2. Check for proper equipment model number from list.. Verify that unit duct work is installed per base unit instructions. 4. Remove top cover of the unit to access heater compartment (See Fig. ). 5. Locate and remove the heater knockout plate in the indoor blower housing (See Fig. &2). 6. Remove electric heater from the packaging. Route control and heater high voltage wire through power and control wiring knockout as shown in Fig.. 7. Install heater, sliding assembly carefully into heater area in the blower housing (See Fig. & 2). Ensure that mounting holes of heater align with mounting holes on the unit. Secure heater assembly with screws provided. 8. Dress wires with wire ties provided. Route heater wires along existing unit wire bundles behind and away from capacitors. 9. Fused Units: Remove fuse links of the fuse block, attach fuse block with screws (2) on mounting holes provided and re-install the fuse links. Attach lid to unit panel with (4) screws provided. Align with existing mounting holes (See Fig. ). 0. Non-Fused Units: Adhere schematic in lieu of fused block inside unit panel (See Fig. 2).. Install ground lug in mounting hole provided adjacent to 24-v. compartment (See Fig. 2). ELECTRICAL CONNECTION. Open all electrical disconnects and install lock-out tag before beginning any installation or service work. 2. All electrical connections, wire sizes and type of conduit shall meet the National Electric Code and State and Local Codes. Main power supply, minimum wire sizes, circuits, fusing, etc. Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book PC 0 Catalog No Printed in U.S.A. Form 50Z-52SI Pg Replaces: 50Z-5SI Tab b 5a
2 UNIT VIEW ATTACHED LID WITH 4 SCREWS ADHERE GASKET (8 x 2 /4) (ON FUSED MODELS) TO UNIT SIDE PANEL BETWEEN FUSE BLOCK AND PANEL POWER AND CONTROL WIRING THROUGH KNOCKOUT BLOWER HOUSING HEATER AREA is shown on schematic wiring diagrams. NOTE: Use minimum 75 C copper wire only.. Refer to base unit instructions for recommended wiring procedures. 4. Connect low voltage wires as shown in heater schematic diagrams (See Figs. 5-22). These connections must be made in the 24-v. barrier section inside the unit panel (See Fig. 2). 5. Connect field power wiring as shown in heater wiring diagram. All connections should be made inside the unit and comply with the National Electric Code and State and Local Codes. Heaters with factory installed fuses may be installed on a branch circuit protected by either a fuse or circuit breaker. For all other heaters, the branch circuit must be protected by a fuse or a circuit breaker supplied by others. 6. Make all high voltage wire splice connections inside the unit control box (See Figs. 5-22). Use splice connectors provided. Properly insulate connectors. Separate all wires from incoming power leads. 7. Be sure that all electrical terminal connections, clamps, screws, etc. are tight before proceeding. 8. Check wiring diagram supplied with heater for specific connections and information. 9. Check operation as described in Start-Up section. Before performing installation, service or maintenance operations on this system turn off all main power switches and/or disconnects. There may be more than one switch or disconnect. Turn off accessory heater power switch if applicable. Electrical shock can cause serious injury or death. TAG DISCONNECT SWITCH(S) WITH A SUITABLE WARNING LABEL. Fig. Unit Control Box (side view) START-UP C0055 Before proceeding, verify that all wiring is correct per factory approved schematic. Notify factory immediately of any discrepancies.. Refer to base unit installation instructions as required. 2. Check for loose terminal connections.. Check that all fuse and circuit breaker short circuit interrupting ratings are adequate. 4. Turn on unit and heater power. 5. Set thermostat to call for heat. 6. Check operation of heater. 7. Check that airflow across the heater is at or above the minimum recommended CFM requirement (See Table 2). Adjust indoor blower heat speed as required. 8. Any modifications or repairs to this equipment without written permission from the factory will be done at the installer s own risk and expense. TABLE 2 Minimum Airflow for Heater Operation UNIT HEAT PUMP ELECTRIC COOLING MINIMUM AIRFLOW (CFM) UNIT SIZE TROUBLESHOOTING. Fuses -Malfunction will interrupt power to the unit. Check for cause of failure, replace fuses.
3 TOP VIEW BLOWER HOUSING PRESSOR CONTACTOR POWER WIRING / CONTROL WIRING / / FUSE BLOCK WHEN REQUIRED ADHERE SCHEMATIC WHEN NON-FUSED GROUND LUG LOCATION (SEE #) BARRIER CONTROL PANEL 24V CAPACITORS HEATER CONTACTORS, POWER & CONTROL WIRING HARNESS USE WIRE TIES 5 PLACES (SEE#8) Fig. 2 Unit Control Box (top view) and Schematic Location C Limit Switch -Malfunction prevents heating element(s) from being energized. Replace switch if malfunction occurs.. Contactor -Malfunction will not allow heater to energize. Replace faulty contactor. Do not attempt to replace coil or dress contacts. PACKAGE CONTENTS ELECTRIC HEATER PACKAGE CONTENTS. Heater assembly. 2. UPC heater label.. Installation Instructions. 4. Identification label. 5. Schematic on lid door for all fused units. 6. Schematic on sticker to be placed inside unit panel for non-fused units (See Fig. 2). 7. Wire connectors (). 8. Wire ties 6 (5). 9. Screws #0B (2). 0. Splice Connectors (4).. Strip Gasket (8 in. x 2-/4 in.) Fused models only (). 2. Hinged lid with latch Fused models only ().. Ground Lug () See Fig. 2.
4 Fig. Typical A/C Wiring Schematic 208/20- C0020 4
5 Fig. 4 Typical Heat Pump Wiring Schematic 208/20- C0022 5
6 E FUSE BLOCK T E T2 T T4 UNIT PANEL HEATER SECTION Replace Auto Reset with Therm-O-Disc type TX0-F0 Replace with 250VAC type Slo-Blow fuses 7.5/0.0 CONTROL STEPS AMPS /4.7 HEATER FUSES T, T T2, T4 A 50A CPHEATER024B00 C0205 Fig. 5 CPHEATER024B00 Wiring Diagram E FUSE BLOCK T E T2 T HR T4 Replace Auto Reset with Therm-O-Disc type TX0-F0 Replace with 250VAC type Slo-Blow fuses./5.0 CONTROL STEPS AMPS /62.5 HEATER FUSES T, T T2, T4 0A A CPHEATER025B00 C02054 Fig. 6 CPHEATER025B00 Wiring Diagram 6
7 E TO UNIT POWER WIRING Replace Auto Reset with Therm-O-Disc type TX0-F0.8/5.0 CPHEATER026B00 CONTROL STEPS AMPS 24 8./20.8 Fig. 7 CPHEATER026B00 Wiring Diagram C02055 E FUSE BLOCK T E T2 T HR T4 HR4 EL4 Replace Auto Reset with Therm-O-Disc type TX0-F5 Replace with 250VAC type Slo-Blow fuses 5.0/20.0 CPHEATER027B00 CONTROL STEPS AMPS /8. Fig. 8 CPHEATER027B00 Wiring Diagram HEATER FUSES T, T T2, T4 A A C
8 E FUSE BLOCK T E T2 T HR T4 HR4 EL4 T5 T6 Replace Auto Reset with Therm-O-Disc type TX0-F5 Replace with 250VAC type Slo-Blow fuses 5.0/20.0 CPHEATER028B00 CONTROL STEPS AMPS /8. Fig. 9 CPHEATER028B00 Wiring Diagram HEATER FUSES T, T6 T2, T, T4, T5 50A A C02057 E E HR L Replace Auto Reset with Therm-O-Disc type TX0-F0.8/5.0 CPHEATER029B00 CONTROL STEPS AMPS /2.0 Fig. 0 CPHEATER029B00 Wiring Diagram C
9 E E HR L Replace Auto Reset with Therm-O-Disc type TX0-F0 7.5/0.0 CPHEATER00B00 CONTROL STEPS AMPS /24. Fig. CPHEATER00B00 Wiring Diagram C02059 E E HR L Replace Auto Reset with Therm-O-Disc type TX0-F0./5.0 CPHEATER0B00 CONTROL STEPS AMPS 24 2./6. Fig. 2 CPHEATER0B00 Wiring Diagram C020 9
10 E FUSE BLOCK T E T2 T HR T4 T5 L T6 Replace Auto Reset with Therm-O-Disc type TX0-F0 Replace with 250VAC type Slo-Blow fuses./5.0 CONTROL STEPS AMPS 24 2./6. HEATER FUSES T, T, T5 T2, T4, T6 50A 0A CPHEATER02B00 C0206 Fig. CPHEATER02B00 Wiring Diagram E FUSE BLOCK T E T2 T HR T4 T5 L T6 Replace Auto Reset with Therm-O-Disc type TX0-F5 Replace with 250VAC type Slo-Blow fuses 4.9/9.9 CONTROL STEPS AMPS /47.9 HEATER FUSES T, T, T5 T2, T4, T6 A 0A CPHEATER0B00 C02062 Fig. 4 CPHEATER0B00 Wiring Diagram 0
11 E E CONTACTOR L Replace Auto Reset with Therm-O-Disc type TXX0-F CPHEATER04B00 CONTROL STEPS AMPS Fig. 5 CPHEATER04B00 Wiring Diagram C0206 E E CONTACTOR L Replace Auto Reset with Therm-O-Disc type TXX0-F CPHEATER05B00 CONTROL STEPS AMPS Fig. 6 CPHEATER05B00 Wiring Diagram C02064
12 E E CONTACTOR L Replace Auto Reset with Therm-O-Disc type TXX0-F CPHEATER06B00 CONTROL STEPS AMPS Fig. 7 CPHEATER06B00 Wiring Diagram C02065 E E CONTACTOR L Replace Auto Reset with Therm-O-Disc type TXX0-F CPHEATER07B00 CONTROL STEPS AMPS Fig. 8 CPHEATER07B00 Wiring Diagram C
13 FUSE BLOCK T E T2 T T4 Replace Auto Reset with Therm-O-Disc type TX0-F0 Replace with 250VAC type Slo-Blow fuses.8/5.0 CPHEATER08B00 CONTROL STEPS AMPS 24 8./20.8 Fig. 9 CPHEATER08B00 Wiring Diagram HEATER FUSES T, T4 T2, T 0A 50A C02067 E E TO UNIT POWER WIRING Replace Auto Reset with Therm-O-Disc type TX0-F0 7.5/0.0 CPHEATER09B00 CONTROL STEPS AMPS 24 6./4.7 Fig. 20 CPHEATER09B00 Wiring Diagram C02068
14 E FUSE BLOCK T E T2 T HR T4 T5 T6 Replace Auto Reset with Therm-O-Disc type TX0-F0 Replace with 250VAC type Slo-Blow fuses./5.0 CPHEATER040B00 CONTROL STEPS AMPS /62.5 T, T6 50A Fig. 2 CPHEATER040B00 Wiring Diagram HEATER FUSES T2, T5 A T, T4 0A C02069 E E TO UNIT POWER WIRING Replace Auto Reset with Therm-O-Disc type TX0-F0 5.6/7.5 CPHEATER042B00 CONTROL STEPS AMPS /. Fig. 22 CPHEATER042B00 Wiring Diagram C
15 5
16 Copyright 2002 Carrier Corporation iik564a24 Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book PC 0 Catalog No Printed in U.S.A. Form 50Z-52SI Pg 6 Replaces: 50Z-5SI Tab b 5a
Installation Instructions Electric Heaters 5 20 kw
Small Packaged Products to 5 Tons Accessory Electric Heaters Cancels: IIK 564A--1 IIK 564A-- 11-01 Installation Instructions Electric Heaters 5 0 kw NOTE: Read the entire instruction manual before starting
More informationInstallation Instructions
NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment
More informationInstallation Instructions
CRPWREXH068A00 CRPWREXH069A00 CRPWREXH070A00 POWER EXHAUST ACCESSORY SINGLE PACKAGE ROOFTOP UNITS 15 to 25 TONS Installation Instructions TABLE OF CONTENTS SAFETY CONSIDERATIONS... 1 GENERAL... 1 INSTALLATION...
More informationInstallation Instructions
265V Subbase Receptacle Accessory Kit For Use With Packaged Terminal Air Conditioner Installation Instructions INTRODUCTION These instructions cover the installation of the 265V Subbase Receptacle Accessory
More informationInstallation Instructions
H068A00 H069A00 H070A00 POWER EXHAUST ACCESSORY SINGLE PACKAGE ROOFTOP UNITS 12.5to25TONS Installation Instructions TABLE OF CONTENTS SAFETY CONSIDERATIONS... 1 GENERAL... 1 INSTALLATION... 2 Power Exhaust
More informationInstallation Instructions
CRPWREXH08A0, CRPWREXH09A0, CRPWREXH08A00, CRPWREXH08A00 For Use With Horizontal EconoMi$er IV, EconoMi$er, or EconoMi$er X (W70) Installation Instructions TABLE OF CONTENTS PACKAGE CONTENTS... PACKAGE
More informationInstallation Instructions
00A0, 0A0-0A0 080A00 08A00 For Use With Vertical EconoMi$ert IV or EconoMi$ert Only SMALL ROOFTOP UNITS ACCESSORY VERTICAL EXHAUST GAS HEATING/ELECTRIC COOLING, ELECTRIC COOLING, AND HEAT PUMP UNITS TO5TON
More informationInstallation Instructions
CRLOWAMB039A00 CRLOWAMB040A00 CRTRXKIT002A00 ACCESSORY MOTORMASTER I HEAD PRESSURE CONTROL KIT 12.5 TON HEAT PUMP Installation Instructions TABLE OF CONTENTS PACKAGE CONTENTS... 1 PRODUCT USAGE... 2 SAFETY
More informationInstallation Instructions
Smart Start Assist Kit For use with Single-Phase Residential Geothermal Heat Pumps 8-733-934-497 Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY
More informationInstallation Instructions
08A0, 09A0, 08A00, 08A00 For Use With Horizontal EconoMi$ert IV or EconoMi$ert Only SMALL ROOFTOP UNITS ACCESSORY HORIZONTAL EXHAUST GAS HEATING/ELECTRIC COOLING, ELECTRIC COOLING, AND HEAT PUMP UNITS
More informationInstallation Instructions
30RAP010-150, 38APS05-065, 38APD05-130 Ground-Fault Interrupter Convenience Outlet Accessory Installation Instructions Part No. 30RA-900---058, 30RA-900---059 SAFETY CONSIDERATIONS Installation of this
More informationInstallation Instructions
010A00 011A00 014A00 SMALL ROOFTOP UNITS TWO POSITION OUTDOOR AIR DAMPER 2to15TONS (50/60 Hz) Installation Instructions TABLE OF CONTENTS PACKAGE CONTENTS... 1 PACKAGE USAGE... 1 SAFETY CONSIDERATIONS...
More informationInstallation Instructions
Installation Instructions Accessory Ultraviolet (UV) Germicidal Lamp 1 & 2 Lamp Models 115-v & 208/230-v UV Lamp C03009 Fig. 1 Two Lamp Model UV Lamp NOTE: Read the entire instruction manual before starting
More informationInstallation Instructions
Outdoor plit Flow Center Kit FCP11BDO (1 pump) FCP21BDO (2 pumps) For plit Geothermal Heat Pump models GZ & H Installation Instructions NOTE: Read the entire instruction manual before starting the installation.
More informationInstallation Instructions
MotorMaster ontrol Kit for Residential Split System Applications ancels: IIK 561-18-1 IIK 561-18-2 9-97 Installation Instructions Part No. 32LT660004 and 005 NOTE: Read the entire instruction manual before
More informationInstallation Instructions
Outdoor plit Flow Center Kit FCP11BDO (1 pump) FCP21BDO (2 pumps) For plit Geothermal Heat Pump models GZ & H Installation Instructions NOTE: Read the entire instruction manual before starting the installation.
More informationCRECOMZR054B00 CRECOMZR055B00. VERTICAL AND HORIZONTAL ECONOMI$ER2 ACCESSORY MEDIUM ROOFTOP UNITS 15 to 27 1/2 TONS WARNING TABLE OF CONTENTS
CRECOMZR05B00 CRECOMZR055B00 VERTICAL AND HORIZONTAL ECONOMI$ER2 ACCESSORY MEDIUM ROOFTOP UNITS 15 to 27 1/2 TONS TABLE OF CONTENTS PACKAGE USAGE...1 SAFETY CONSIDERATIONS...1 PACKAGE CONTENTS...1 GENERAL...2
More informationInstallation Instructions
KSACN0101AAA Wired Remote Controller (with Timer Function) For Ductless Systems Installation Instructions NOTES: Read the entire instruction manual before starting the installation. TABLE OF CONTENTS PAGE
More informationInstallation Instructions
CRLVHLGD004A00 CRLVHLGD011A00- CRLVHLGD016A00, CRLVHLGD020A00- CRLVHLGD024A00 CRLVHLGD032A00 SMALL ROOFTOP UNITS ACCESSORY LOUVERED HAIL GUARD GAS HEATING/ELECTRIC COOLING, ELECTRIC COOLING AND HEAT PUMP
More informationOwner s Information Manual
50ES---A and 50VL---C Comfort 13SEERThreePhase2½---5NominalTons (Sizes 30---60) Comfort 14 SEER Single and Three Phase 2---5 Nominal Tons (Sizes 24---60) Single Packaged Air Conditioner System With Puronr
More informationInstallation Instructions
Installation Instructions External Filter Rack KGAFR0301ALL NOTE: Read the entire instruction manual before starting the installation. INTRODUCTION The External Filter Rack is designed to fit on either
More informationINSTALLATION INSTRUCTIONS TABLE OF CONTENTS
KSAIF0401AAA Wi-Fi Interface Kit for Ductless Systems INSTALLATION INSTRUCTIONS NOTE: Read and become familiar with these instructions before beginning installation. TABLE OF CONTENTS PAGE SAFETY CONSIDERATIONS...
More informationInstallation Instructions
Motor Master ontrol Kit ancels: IIK 561A-18-1 IIK 561-18-1 11-95 Installation Instructions Part No. 32LT660004 and 005 This symbol indicates a change since last issue. INTRODUTION These instructions cover
More informationInstallation Instructions
KALA0601AAA KALA0701AAA MotorMasterR Low Ambient Controller for Residential plit ystem Applications Installation Instructions Fig. 1 - MotorMasterr Low Ambient Controller A93157 NOTE: Read the entire instruction
More informationSupplemental Installation Instructions -- August 2016
EnergyX R System Factory---Installed Energy Recovery Ventilator 48/50HC WeatherMasterr Commercial Rooftop Units 7.5 to 12.5 Nominal Tons with Puronr (R---410A) Refrigerant and ComfortLink Controls Supplemental
More informationSupplemental Installation Instructions -- August 2016
EnergyX R System Factory---Installed Energy Recovery Ventilator 48/50HC WeatherMasterr Commercial Rooftop Units 15 to 25 Nominal Tons with Puronr (R---410A) Refrigerant and ComfortLink Controls Supplemental
More informationInstallation Instructions
018A00 CALOWAMB023A00 CALOWAMB037A00 - CALOWAMB042A00 SPLIT SYSTEM AC UNITS ACCESSORY MOTORMASTER R I HEAD PRESSURE CONTROLLER 15 & 20 TONS Installation Instructions IMPORTANT: Read these instructions
More informationInstallation Instructions
Installation Instructions Downflow Conversion Kit KFADC NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. SAFETY CONSIDERATIONS
More informationElectrical Data Supplement
48TC 3 to 15 Nominal Tons Single Package Rooftop Gas Heating/Electric Cooling Unit with Puronr (R---410A) Refrigerant Sizes: 04---16 Electrical Data Supplement FOR MODELS PRODUCED ON OR AFTER JULY 30,
More informationElectrical Data Supplement
48/50TC 15---25 Nominal Tons Single Package Rooftop, Horizontal Air Flow Gas Heating/Electric Cooling Unit & Cooling Only/Electric Heat Unit with Puronr (R---410A) Refrigerant Sizes: 18---29 Electrical
More informationINSTALLATION INSTRUCTIONS FOR EGA AND EGH SERIES ELECTRIC HEATERS IN V OR H SERIES UNITS
INSTALLATION INSTRUCTIONS FOR EGA AND EGH SERIES ELECTRIC HEATERS IN V OR H SERIES UNITS NOTE TO INSTALLER The words SHALL and MUST indicate a requirement which is essential to satisfactory and safe product
More informationElectrical Data Supplement
48HC15to25NominalTons Single Package Rooftop Gas Heating/Electric Cooling Unit with Puronr (R---410A) Refrigerant Sizes: 17---28 Electrical Data Supplement FOR MODELS PRODUCED ON OR AFTER JULY 30, 2012
More informationElectrical Data Supplement
50HCQ3to10inalTons Single Package Rooftop Heat Pump with Puronr (R---410A) Refrigerant Sizes: 04---12 Electrical Data Supplement FOR MODELS PRODUCED ON OR AFTER JULY 30, 2012 ONLY! NOTE: Read the entire
More informationELECTRIC HEAT ACCESSORY INSTALLATION INSTRUCTION. 20, 30 & 40 kw for 15 Ton Split System Air Conditioners Models: LB180 & LL A-0102
INSTALLATION INSTRUCTION ELECTRIC HEAT ACCESSORY 20, 30 & 40 kw for 15 Ton Split System Air Conditioners Models: LB180 & LL-15 CONTENTS GENERAL...2 NOTES, CAUTIONS AND WARNINGS........... 2 REFERENCE...2
More informationTechnical Manual. DLM Module. This manual should remain with the unit.
Technical Manual DLM Module This manual should remain with the unit. Safety Rules SAVE THESE INSTRUCTIONS! Read the following information carefully before attempting to install, operate or service this
More informationInstallation Instructions
HH57AC078 CRENTDIF004A00 ROOFTOP UNITS, 2 to 25 TONS ACCESSORYENTHALPYAND DIFFERENTIAL ENTHALPY FOR ECONOMI$ERt IV Installation Instructions TABLE OF CONTENTS PACKAGE CONTENTS - HH57AC078... 1 PACKAGE
More informationInstallation Instructions
ROOFTOP UNITS, 3 to 25 TONS ACCESSORY TEMPERATURE FOR SINGLE OR DIFFERENTIAL DRY BULB CONTROL FOR ECONOMI$ERt IV Installation Instructions TABLE OF CONTENTS PACKAGE CONTENTS... 1 SAFETY CONSIDERATIONS...
More informationWiring Diagrams DIAGRAM INDEX
30HK040-060;30HL050,060;30HW018-040 Reciprocating Liquid Chillers with ComfortLink Controls 50/60 Hz Wiring Diagrams DIAGRAM INDEX UNIT 30 VOLTAGE DIAGRAM TYPE FIGURE LABEL DIAGRAM All Component Arrangement
More informationInstallation Instructions
FILCAB Filter Cabinet Sizes 6 --- in., 0 --- in., 4 --- in. For Non---Condensing and Condensing Gas Furnaces and FILCAB Accessory Kits Installation Instructions NOTE: Read the entire instruction manual
More informationInstallation and Start-Up Instructions
Visit www.carrier.com SYSTXCC4ZC01 Infinity Control Installation and Start-Up Instructions Infinity Control SYSTXCC4ZC01 A97040 NOTE: Read the entire instruction manual before starting the installation.
More informationInstallation Instructions
8/0A,A,A,A,AJ,AK,AW,AY00-00 Power Exhaust, Barometric Relief, and Conversion Package Accessories Installation Instructions Power Exhaust Part Numbers: CRPWREXH0A00, CRPWREXH0A00, CRPWREXH0A00, CRPWREXH0A00
More informationInstallation Instructions
CAHZCOIL8A00 CAHZCOIL412A00 CAHZCOIL208A00 CAHZCOIL212A00 CAVTCOIL8A00 CAVTCOIL412A00 CAVTCOIL208A00 CAVTCOIL212A00 Installation Instructions DIRECT --- EXPANSION HORIZONTAL AND VERTICAL EVAPORATOR COILS
More informationInstallation Instructions
Accessory Ultra-Violet Germicidal Lamps 40RM007-034, 40RMQ008-016 and 40RMS008-024 Air Handler Units Installation Instructions Part Numbers: CRDBLFIX001A00, CRDBLFIX002A00, CRDBLFIX003A00, CRDBLFIX004A00,
More informationOwner's/Installation Manual
Owner's/Installation Manual Power Management Module (PMM) and Starter Kit NOTE: The starter kit must be purchased and installed prior to individual PMM usage. Model Numbers: 00686-0 PMM 00699-0 PMM WITH
More informationTECHNICAL SUPPORT MANUAL Split System Air Conditioner H4A3, 3 Phase
TECHNICAL SUPPORT MANUAL Split System Air Conditioner H4A3, 3 Phase DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU- TION, and NOTE are used to identify levels of hazard seriousness.
More informationInstallation Instructions
CALOWAMB001A00 - CALOWAMB011A00 CALOWAMB030A00 - CALOWAMB036A00 SPLIT SYSTEMS ACCESSORY MOTORMASTER R I HEAD PRESSURE CONTROLLER 6to12.5TONS Installation Instructions IMPORTANT: Read these instructions
More informationUL/NEMA Type 1 & Type 12 FRENIC-HVAC Combination VFD
UL/NEMA Type 1 & Type 12 FRENIC-HVAC Combination VFD Safety Precautions Read this manual thoroughly before proceeding with installation, connections (wiring), or maintenance and inspection. Ensure you
More informationAHKD SERIES ELECTRIC RESISTANCE HEAT KITS INSTALLATION & OPERATING INSTRUCTIONS
AHKD SERIES ELECTRIC RESISTANCE HEAT KITS INSTALLATION & OPERATING INSTRUCTIONS Made in the USA by: Goodman Manufacturing Company, L.P. 2550 North Loop West, Suite 400 IO-608 Houston, TN 77092 AHKD SERIES
More informationTECHNICAL SUPPORT MANUAL Split System Heat Pump H2H3, 3 Phase
TECHNICAL SUPPORT MANUAL Split System Heat Pump H2H3, 3 Phase DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU- TION, and NOTE are used to identify levels of hazard seriousness.
More informationIMPORTANT ATTENTION INSTALLERS:
Power Exhaust Kit for P7TQ, Q7TQ & R7TQ Series INSTALLATION INSTRUCTIONS IMPORTANT ATTENTION INSTALLERS: It is your responsibility to know this product better than your customer. This includes being able
More informationInstallation Instructions
PLOWAMB001A00 SMALL ROOFTOP UNITS GAS HEAT/ELETRI OOLING, ELETRI OOLING AND HEAT PUMP UNITS AESSORY MOTORMASTERR II HEAD PRESSURE ONTROLLER 60Hz 3to12---1/2tons Installation Instructions IMPORTANT: Read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Ultraviolet Single and Dual Germicidal Lamps 60 Hz Part Numbers: P103-UVLTT1LP1020A01, P103-UVLTT1LP3020A01, P103-UVLTT2LP1020A01, P103-UVLTT2LP3020A01 SAFETY CONSIDERATIONS Installation
More informationInstallation Instructions For Motor Control Center (MCC) Units
s Page 1 of 8 Installation Instructions December, 2013 Installation Instructions For Motor Control Center (MCC) Units Hazardous voltage. Will cause death or serious injury. Always de-energize and ground
More informationInstallation Instructions
H3HK Series Installation Instructions Large Package Electric Heater Kits Description Installation of 208/240V H3HK Heater Kits in Packaged Air Conditioners and Packaged Heat Pumps. These instructions are
More informationSERVICE INSTRUCTIONS
USA SERVICE OFFICE Dometic, LLC 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic, LLC 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 3313107.107 5 BUTTON THERMOSTAT
More informationLED Downlight Ceiling Fixtures
ED Downlight Ceiling Fixtures Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences, directly
More informationTECHNICAL SUPPORT MANUAL Split System Air Conditioner N2A0, 3-Phase
TECHNICAL SUPPORT MANUAL Split System Air Conditioner N2A0, 3-Phase DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU TION, and NOTE are used to identify levels of hazard seriousness.
More informationTECHNICAL SUPPORT MANUAL Split System Heat Pump R2HM, R2H3, WCH3**2
TECHNICAL SUPPORT MANUAL Split System Heat Pump R2HM, R2H3, WCH3**2 DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU- TION, and NOTE are used to identify levels of hazard seriousness.
More informationINSTRUCTIONS FOR THE RELIANCE Fast/Tran TM ARL0909 & ARL0909R
INSTRUCTIONS FOR THE RELIANCE Fast/Tran TM ARL0909 & ARL0909R THE RELIANCE Fast/Tran IS NOT FOR "DO-IT-YOURSELF" INSTALLATION. It must be installed by a qualified electrician thoroughly familiar with all
More informationMODEL SCA Installation and Operation Manual Important:
MODEL SCA Installation and Operation Manual Important: This manual contains specific cautionary statements relative to worker safety. Read this manual thoroughly and follow as directed. It is impossible
More informationdv Sentry TM 208V 600V INSTALLATION GUIDE Quick Reference ❶ How to Install Pages 6 14 ❷ Startup/Troubleshooting Pages WARNING
dv Sentry TM 208V 600V INSTALLATION GUIDE FORM: DVS-IG-E REL. January 2018 REV. 003 2018 MTE Corporation High Voltage! Only a qualified electrician can carry out the electrical installation of this filter.
More informationModel G14SD Vapor Management System
Instruction Manual Model G14SD Vapor Management System (For Models: DSD and SSD 110/115v) Manufactured in USA for Medivators Reprocessing Systems by: PCI Medical Inc. 12 Bridge Street, PO Box 188 Deep
More informationWiring Diagrams (Including Accessories) (50/60 Hz)
UNIT 38AKS 028-044 ELECTRICAL CHARACTERISTICS (V-Ph-Hz) 208/230-3-60 460-3-60 575-3-60 230-3-50 346-3-50 380-3-60 400-3-50 Typical Field Wiring Electronic Programmable Thermostat, Liquid Line Solenoid
More informationInstallation Instructions
Installation Instructions Part No. 50DJ902791 48/50FP,JP,MP,NP 50FPX,FPY,JPX,JPY 50FB,JB,NB Accessory Outdoor-Air Cfm Kit CONTENTS GENERAL........................................ 1 INSTALLATION................................
More informationInstallation Manual. E-design A Transfer Switches A
ASCO 3ATS & 3NTS 3ATS & 3NTS E-design 260-400 A Transfer Switches DANGER is used in this manual to warn of a hazard situation which, if not avoided, will result in death or serious injury. is used in this
More informationInstallation Instructions
PART NUMBER: CPLPCONV007A00 60,000---130,000 BTU/HR 2TO5TONS SMALL PACKAGED PRODUCTS GAS HEATING/ELECTRIC COOLING UNITS HIGH ALTITUDE ONLY 2001---6000 FT PROPANE CONVERSION KIT Installation Instructions
More informationINSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS. Part Number: P DM
INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS Whole House Duct-Mount HEPA Air Cleaner Part Number: P102-400DM TABLE OF CONTENTS Page SAFETY CONSIDERATIONS...1 INTRODUCTION...1,2 INSTALLATION...2,3
More informationWiring Diagrams DIAGRAM INDEX. POWER SCHEMATICS Figure Number. Label Diagram No. 30HX ALL ALL
Wiring Diagrams 30HXA, 30HXC Condenserless and Fluid-Cooled Chillers 50/60 Hz DIAGRAM INDEX POWER SCHEMATICS Unit 30HXA,C Voltage Figure Number Label Diagram No. 30HX 076-186 ALL 1 500141 206-271 ALL 2
More informationINSTALLATION, START-UP AND SERVICE INSTRUCTIONS
INSTALLATION, START-UP AND SERVICE INSTRUCTIONS P705 Refrigeration Condensing Units CONTENTS Page SAFETY CONSIDERATIONS...................... 1 INTRODUCTION.................................. 1 HANDLING.......................................
More informationTECHNICAL SUPPORT MANUAL Fan Coils FSM4X6000AT
Fan Coils FSM4X60 DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU- TION, and NOTE are used to identify levels of hazard seriousness. The signal word DANGER is only used on product
More informationLIGHT COMMERCIAL - 3 HP ECM MOTOR / CONTROLLER HIGH STATIC DRIVE KITS
LIGHT COMMERCIAL - 3 HP ECM MOTOR / CONTROLLER HIGH STATIC DRIVE KITS INSTALLATION INSTRUCTIONS For R7TQ/P7TQ/Q7TQ -090 (T) and -120 (T) Series Single Package Rooftop Units IMPORTANT ATTENTION INSTALLERS:
More informationAUXILIARY ELECTRIC HEATER KITS FOR 7.5, 10, 15 AND 20 TON COMMERCIAL AIR HANDLERS RXHE-CE, DE
AUXILIARY ELECTRIC HEATER KITS FOR 7., 10, 1 AND 20 TON COMMERCIAL AIR HANDLERS RXHE-CE, DE WARNING: THIS ACCESSORY IS TO BE INSTALLED BY A QUALIFIED, LICENSED SERVICE PERSON. TO AVOID UN - SATISFACTORY
More informationInstallation Instructions
CR0A00 - CR9A00, CR264A00 - CR269A00, CR288A00 - CR296A00 CRSINGLE037A00 - CRSINGLE054A00 SMALL ROOFTOP UNITS ACCESSORY ELECTRIC AND SINGLE POINT BOX ELECTRIC COOLING AND HEAT PUMP 3to2---/2TONS Installation
More informationManual Transfer Switch
Manual Transfer Switch Instruction Manual 30 1200 Amp 2, 3 & 4 Pole Page 1 WARNING Before Installation READ THIS MANUAL carefully to learn how to properly install, operate and maintain this unit. Personal
More informationINSTALLATION INSTRUCTIONS
H3HK Series INSTALLATION INSTRUCTIONS Package Electric Heater Kits Installation of H3HK Heater Kits (208/240V & 460V) in Packaged Air Conditioners & Packaged Heat Pumps. IMPORTANT These instructions are
More informationOperator's Manual. Storage System. Ultrasound Probe Cabinet. Manufactured by:
Storage System Ultrasound Probe Cabinet Operator's Manual Manufactured by: CIVCO Medical Solutions 102 First Street South Kalona, IA 52247 USA 319.248.6757 / 800.445.6741 WWW.CIVCO.COM Copyright 2018 All
More informationO & M Manual for the EATON Generator Ready Loadcenter
O & M Manual for the EATON Instructional Booklet New Information Description Page 1. Introduction............................... 2 2. Receiving, Handling, and Storage................ 4 3. Equipment Description........................
More informationTECHNICAL SUPPORT MANUAL Split System Air Conditioner N2A3, 3-Phase
Split System Air Conditioner N2A3, 3-Phase DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU TION, and NOTE are used to identify levels of hazard seriousness. The signal word DANGER
More informationDouble Pole Circuit Breaker Kit for Non-Regenerative MinPak Plus DC Drives
Double Pole Circuit Breaker Kit for Non-Regenerative MinPak Plus DC Drives Model Numbers 14C210, 14C211, 14C212, and 14C213 Instruction Manual D2-3385! ATTENTION: Only qualified electrical personnel familiar
More informationSINAMICS G130. Motor reactors. Operating Instructions 05/2010 SINAMICS
SINAMICS G130 Operating Instructions 05/2010 SINAMICS s Safety information 1 General 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions
More informationSYST0101ZP Ion Damper Control Installation and Start---Up Instructions
SYST0101ZP Ion Control Installation and Start---Up Instructions A97040I NOTE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS Improper installation, adjustment,
More informationINSTALLATION & OPERATION MANUAL. Fan Powered Terminals VAV TERMINALS. Redefine your comfort zone.
INSTALLATION & OPERATION MANUAL Fan Powered Terminals VAV TERMINALS IOM FAN POWERED TERMINALS Receiving Inspection After unpacking the terminal, check it for shipping damage. If any shipping damage is
More informationInstallation Instructions
GEMINI SELECT 38APS025-065, 38APD025-130 Air-Cooled Condensing Units with PURON Refrigerant (R-410A) 50/60 Hz Installation Instructions CONTENTS Page SAFETY CONSIDERATIONS...................... 1 INSTALLATION................................
More informationSM-1700 Secondary Shunt Trip Coil Assembly. Powered by Safety
SM-1700 Secondary Shunt Trip Coil Assembly Powered by Safety SM-1700 Secondary Shunt Trip Coil Assembly SM-1700 Contact Information Powell Electrical Systems, Inc. www.powellind.com info@powellind.com
More informationpoollux Power plx-pw60 & plx-pw100
poollux Power plx-pw60 & plx-pw100 ETL LISTED Conforms to UL STD 379; Certifi.ed.to.CSA.STD.C22.2.#218.1 5005508 Installation Instructions Read all instructions before attempting to perform installation
More informationTECHNICAL SUPPORT MANUAL Split System Air Conditioner (C,H,T)4A3
Split System Air Conditioner (C,H,T)4A3 DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU TION, and NOTE are used to identify levels of hazard seriousness. The signal word DANGER
More information3. Please ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
FLUORESCENT EMERGENCY BALLAST WARNING: When using this lighting device, safety precautions should be followed at all times. CAUTION: Verify that all replacement lamp types marked on the installed luminaire
More informationFlorham Park, NJ USA Call (ASCO) for sales or service
Operator s Manual 7000 Series ATS Automatic Transfer Switches D design, 30 through 230 A DANGER is used in this manual to warn of a hazard situation which, if not avoided, will result in death or serious
More informationInstallation and Start Up Instructions
SYSTXCC4ZC01 Infinityr Control Installation and Start Up Instructions A97040 NOTE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS Improper installation, adjustment,
More informationMODELS DSH/KSH/DSV/KSV R-410A LOW-AMBIENT KIT
MODELS DSH/KSH/DSV/KSV R-410A LOW-AMBIENT KIT Supersedes Form145.10-IOM1 (810) Form 145.10-IOM1 (910) LOW-AMBIENT KIT MODELS DSH/KSH/DSV/KSV R-410A AIR CONDITIONING UNITS INSTALLATION INSTRUCTIONS IMPORTANT!
More informationTECHNICAL SUPPORT MANUAL WT A Coils for Replacement Service EXA, EPA
WT A Coils for Replacement Service EXA, EPA DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU- TION, and NOTE are used to identify levels of hazard seriousness. The signal word DANGER
More informationInstallation, Start-Up and Service Instructions
Installation, Start-Up and Service Instructions 48AJ,AK,AW,AY020-060 with Reciprocating Compressor 48EJ,EK,EW,EY024-068 Single Package Rooftop Units Electric Cooling/Gas Heating CONTENTS Page SAFETY CONSIDERATIONS......................
More informationPF Guard Power Factor Capacitor Bank Installation, Operation, and Maintenance Manual
PF Guard Power Factor Capacitor Bank Installation, Operation, and Maintenance Manual No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
More informationTECHNICAL SUPPORT MANUAL Split System Air Conditioner N2A3
Split System Air Conditioner N2A3 DANGER, WARNING, CAUTION, and NOTE The signal words DANGER, WARNING, CAU- TION, and NOTE are used to identify levels of hazard seriousness. The signal word DANGER is only
More informationACCESSORY KIT INSTALLATION INSTRUCTIONS
ACCESSORY KIT INSTALLATION INSTRUCTIONS ELECTRIC HEAT ACCESSORY MODELS THROUGH 55 AND HH5 & 55 NOTE: These heater accessories may be installed before or after the unit has been set on a curb or slab. Table
More informationTest Cabinet (Inspection Box) Instructions. for Testing Accessories on Manually and Electrically Operated EntelliGuard G Low Voltage Circuit Breakers
DEH41480 Test Cabinet (Inspection Box) for Testing Accessories on Manually and Electrically Operated EntelliGuard G Low Voltage Circuit Breakers Instructions 1 Table of Contents Section 1. Introduction
More informationHigh Velocity Series Air Curtains
INSTALLATION & OPERATING INSTRUCTIONS & PARTS MANUAL FOR ALL 208-230/480 VOLT 3 PHASE. MOTOR MODELS High Velocity Series Air Curtains READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR
More informationMatrix APAX. 380V-415V 50Hz TECHNICAL REFERENCE MANUAL
Matrix APAX 380V-415V 50Hz TECHNICAL REFERENCE MANUAL WARNING High Voltage! Only a qualified electrician can carry out the electrical installation of this filter. Quick Reference ❶ Performance Data Pages
More informationUser s Manual. ACS550-CC Packaged Drive with Bypass Supplement for ACS550-01/U1 Drives User s Manual
User s Manual ACS550-CC Packaged Drive with Bypass Supplement for ACS550-01/U1 Drives User s Manual ii ACS550-CC Packaged Drive with Bypass ACS550 Drive Manuals GENERAL MANUALS ACS550-01/U1 Drives User's
More informationEnvironmental Series Air Curtains
INSTALLATION & OPERATING INSTRUCTIONS & PARTS MANUAL FOR ALL 120 and 230 VOLT 1/4, 1/2 AND 3/4 H.P. MOTOR MODELS Environmental Series Air Curtains READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,
More information