Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Transcription

1 is your source for quality new and certified-used/pre-owned equipment FAST SIPPING AND DELIVER TENS OF TOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS UNDREDS OF MANUFACTURERS SUPPORTED LEASING/MONTL RENTALS ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center SM InstraView REMOTE INSPECTION Remotely inspect equipment before purchasing with our interactive website at Contact us (888) 88-SOURCE E BU USED EQUIPMENT Sell your excess, underutilized, and idle used equipment e also offer credit for buy-backs and trade-ins /ebuyequipment LOOKING FOR MORE INFORMATION? Visit us on the web at for more information on price quotations, drivers, technical specifications, manuals, and documentation

2 Rasmi Electronics Footprint and Book type RFI Filters for Omron Inverters and Servo Drives RFI Filters for October 1st G3EV Series Page 3 3G3JV Series Page 4 3G3MV Series Page 5 3G3FV Series Page 6 3G3RV and 3G3PV 200V Series Page 7 3G3RV and 3G3PV 400V Series Page 8 R88D U and Series Page 9 PFO Cable Chokes Page 10 Installation Recommendations Page ALL PRICES ARE EX-ORKS RASMI ELECTRONICS, UK. ALL ABOVE GOODS ARE EX-STOCK DESPATC MAXIMUM SEVEN DAS FROM RECEIPT OF ORDER. rev /01 (1) (888) 88-SOURCE

3 Requirements Recent European legislation on EMC imposes limits on RF emissions from electrical equipment. The PFI and FIU ranges of power line filters have been specifically developed for use with Omron motor drives, enabling systems incorporating them to meet the European RFI emissions standards for domestic or industrial use. For drives up to 15k, the filters are of a footprint design. These are installed between the drive and the panel, keeping the panel area required to a minimum. For larger drives the filter is mounted separately, alongside. European Standards The European Standard for EMC of Adjustable Speed Electrical Power Drive Systems, EN , requires all drives using below 25A per phase to meet domestic emissions limits (EN55011 Class B). Systems using more than 25A per phase should meet industrial emission limits (EN55011 Class A). Ranges Covered Inverters 200V single phase 200V three phase 400V three phase filter 3G3EV 0.1 to 1.5k - footprint 0.7 to 1.5k - footprint 3G3JV 0.1 to 1.5k - footprint 0.1 to 4.0k - footprint 0.2 to 4.0k - footprint 3G3MV 0.1 to 4.0k - footprint 0.1 to 7.5k - footprint 0.2 to 7.5k - footprint 3G3FV 0.4 to 15k - footprint 18.5 to 300k - standard 3G3RV 0.4 to 18.5k - footprint 0.4 to 18.5k - footprint 22 to 45k - book 22 to 90k - book AC Servo Drives 200V single phase 200V three phase 400V three phase filter R88D U 30 to footprint 1.0 to 5.0k - footprint R88D 30 to footprint 0.5 to 3.0k - footprint Construction All filters carry the mark in accordance with the Low Voltage Directive. Self-healing X and capacitors approved to VDE, SEMKO, UL. Components encapsulated with UL 94-V0 flammability class resin in larger filters. Input and output connections by shrouded terminals (up to 15k), stud bolts or bus bars. Earthing by stud bolt or bus bar directly to the casing. Earth Leakage Nuisance tripping of earth leakage breakers is a common problem associated with EMC filters. The circuits used in the Omron drive filter ranges feature very low leakage currents to avoid this problem. Typical earth leakages are- Single phase filter 3.5mA 3 phase filter up to 15k 28mA 3 phase filter k mA These are "worst case" currents, that may occur when a supply phase is disconnected or momentarily during switch-on. The nominal earth leakage current during normal operation is less than 1mA. Operating Conditions Ambient operating temperature range of -10 C to +40 C. Temperature rise of no more than 50 C at the rated current. 150% overload permissible for up to 60 seconds. PFO Chokes The PFO output chokes can be used in conjunction with the filters to improve EMC performance. They are especially effective where radiated emissions from long drive to motor cables are a problem. Use of Filters with 200V Three Phase Inverters These filter ranges may also be used with 200V three phase inverters, but care should be taken in the filter selection. The equivalent 200V model of an inverter will require approximately twice the current of the 400V model. For example, the 3G3FV PFI 4012E filter is suitable for the 3G3FV A2015 drive but not the 3G3FV A2037, even though the latter will fit. Running a filter on under-voltage is perfectly acceptable, but running at over-current for any extended period is not advisable. Technical Information For more technical data, a separate data sheet is available for each filter model. This gives detailed dimensions, circuit diagram and electrical ratings. (2) (888) 88-SOURCE

4 Filters for 3G3EV Series Inverters Footprint Type Design- Preleaded for motor cables up to 100m Drive Filter Current L X d price 3G3EV AB001 3G3EV AB002 3G3EV PFI 1010E (N) 10A M G3EV AB004 3G3EV AB007 3G3EV PFI 1015E (N) 10A M G3EV AB015 3G3EV PFI 1020E 20A M G3EV A4007 3G3EV PFI 3006E 6A M G3EV A4015 3G3EV PFI 3008E 8A M Footprint Type Design for motor cables up to 10m Drive Filter Current L X d price 3G3EV AB001 3G3EV AB002 3G3EV PFI 1010E M G3EV AB004 3G3EV AB007 3G3EV PFI 1015E M (3) (888) 88-SOURCE

5 Filters for 3G3JV Series Inverters Footprint Type Design- Preleaded Drive Filter Rated Earth L X d price Current Leakage* (mm) (mm) (euro) 3G3JV AB001 3G3JV AB002 3G3JV PFI 1010E 10A 7.0mA M G3JV AB004 3G3JV AB007 3G3JV PFI 1020E 20A 7.0mA M G3JV AB015 3G3JV A2001 3G3JV A2002 3G3JV PFI 2010E 10A 0.3/26mA M G3JV A2004 3G3JV A2007 3G3JV A2015 3G3JV PFI 2020E 16A 0.3/16mA M G3JV A2022 3G3JV A2040 3G3JV PFI 2030E 26A 0.4/30mA M G3JV A4002 3G3JV PFI 3005E 5A 0.5/29mA M G3JV A4004 3G3JV A4007 3G3JV A4015 3G3JV PFI 3010E 10A 0.5/29mA M G3JV A4022 3G3JV A4030 3G3JV PFI 3020E 15A 0.5/29mA M G3JV A4040 * Earth leakage for three-phase is nominal / maximum (three phases / one phase connected). (4) (888) 88-SOURCE

6 Filters for 3G3MV Series Inverters Footprint Type Design- Preleaded Drive Filter Rated Earth L X d price Current Leakage* (mm) (mm) (euro) 3G3MV AB001 3G3MV AB002 3G3MV PFI 1010E 10A 7.0mA M G3MV AB004 3G3MV AB007 3G3MV PFI 1020E 20A 7.0mA M G3MV AB015 3G3MV AB022 3G3MV PFI 1030E 30A 3.5mA M G3MV AB040 3G3MV PFI 1040E 40A 3.5mA M G3MV A2001 3G3MV A2002 3G3MV PFI 2010E 10A 0.3/26mA M G3MV A2004 3G3MV A2007 3G3MV A2015 3G3MV PFI 2020E 16A 0.3/16mA M G3MV A2022 3G3MV A2040 3G3MV PFI 2030E 26A 0.3/17mA M G3MV A2055 3G3MV PFI 2050E 50A 0.6/57mA M G3MV A2075 3G3MV A4002 3G3MV A4004 3G3MV PFI 3005E 5A 0.5/29mA M G3MV A4007 3G3MV A4015 3G3MV PFI 3010E 10A 0.5/29mA M G3MV A4022 3G3MV A4030 3G3MV PFI 3020E 15A 0.5/29mA M G3MV A4040 3G3MV A4055 3G3MV PFI 3030E 30A 0.7/60mA M G3MV A4075 * Earth leakage for three-phase is nominal / maximum (three phases / one phase connected). (5) (888) 88-SOURCE

7 Filters for 3G3FV Series Inverters Footprint Type Design up to 15k for motor cables up to 100m XL Drive Filter Current L X d price 3G3FV A4004 3G3FV A4007 3G3FV A4015 3G3FV PFI 4012E M G3FV A4022 3G3FV A4037 3G3FV A4055 3G3FV A4075 3G3FV PFI 4025E M G3FV A4110 3G3FV A4150 3G3FV PFI 4040E M Standard Type Design over 15k for motor cables up to 100m LX Drive Filter Current L X d price 3G3FV B4185 3G3FV B4220 3G3FV PFI 4060E M G3FV B4300 3G3FV B4370 3G3FV PFI 4100E M G3FV B4450 3G3FV PFI 4120E M G3FV B4550 3G3FV PFI 4150E M G3FV B4750-E 3G3FV PFI 4180E M G3FV B411K-E 3G3FV PFI 4280E M G3FV B416K-E 3G3FV B418K-E 3G3FV PFI 4450E M G3FV B422K-E 3G3FV PFI 4600E M G3FV B430K-E 3G3FV PFI 4900E M (6) (888) 88-SOURCE

8 Filters for 3G3RV and 3G3PV 200V Series Inverters Footprint Type Design up to 18.5k Designed to meet EN55011 Class B (domestic environment) with up to 25m motor cable and EN55011 Class A (industrial environment) with up to100m motor cable. line load Drive Filter Current L X d price 3G3RV(PV) A2004-E 3G3RV(PV) A2007-E 3G3RV PFI 3010E M G3RV(PV) A2015-E 3G3RV(PV) A2022-E 3G3RV PFI 3018E M G3RV(PV) A2037-E 3G3RV PFI 2035E M G3RV(PV) A2055-E 3G3RV(PV) A2075-E 3G3RV PFI 2060E M G3RV(PV) A2110-E 3G3RV(PV) A2150-E 3G3RV PFI 2100E M G3RV(PV) A2185-E Book Type Design over 18.5k Designed to meet EN55011 Class A (industrial environment) with up to 100m motor cable. line L X load Drive Filter Current L X d price 3G3RV(PV) B2220-E 3G3RV PFI 2130E M G3RV(PV) B2300-E 3G3RV(PV) B2370-E 3G3RV PFI 2160E M G3RV(PV) B2450-E 3G3RV PFI 2200E M G3RV(PV) B2550-E 3G3RV(PV) B2750-E under development 3G3RV(PV) B2900-E 3G3RV(PV) B211K-E (7) (888) 88-SOURCE

9 Filters for 3G3RV and 3G3PV Series Inverters Footprint Type Design up to 18.5k Designed to meet EN55011 Class B (domestic environment) with up to 25m motor cable and EN55011 Class A (industrial environment) with up to100m motor cable. line load Drive Filter Current L X d price Book Type Design over 18.5k Designed to meet EN55011 Class A (industrial environment) with up to 100m motor cable. 3G3RV(PV) A4004-E 3G3RV(PV) A4007-E 3G3RV PFI 3010E M G3RV(PV) A4015-E 3G3RV(PV) A4022-E 3G3RV(PV) A4037-E 3G3RV PFI 3018E M G3RV(PV) A4055-E 3G3RV(PV) A4075-E 3G3RV PFI 3035E M G3RV(PV) A4110-E 3G3RV(PV) A4150-E 3G3RV PFI 3060E M G3RV(PV) A4185-E line L X load Drive Filter Current L X d price 3G3RV(PV) B4220-E 3G3RV PFI 3070E M G3RV(PV) B4300-E 3G3RV(PV) B4370-E 3G3RV PFI 3100E M G3RV(PV) B4450-E 3G3RV(PV) B4550-E 3G3RV PFI 3130E M G3RV(PV) B4750-E 3G3RV PFI 3170E M G3RV(PV) B4900-E 3G3RV PFI 3200E M G3RV(PV) B411K-E 3G3RV(PV) B413K-E 3G3RV(PV) B416K-E under development 3G3RV(PV) B418K-E 3G3RV(PV) B422K-E 3G3RV(PV) B430K-E (8) (888) 88-SOURCE

10 Filters for R88D U Series Servo Drives Footprint Type Design Drive Filter Current L X d price R88D UA02 R88D UA03 R88D UA04 R88A FIU 105E M R88D UA08 R88D UA12 R88A FIU 110E M R88D UA20 R88A FIU 115E M R88D UT40 R88A FIU 4020E M R88D UT60 R88D UT80 R88A FIU 4040E M R88D UT110 R88D UT120 R88A FIU 4060E M Filters for R88D Series Servo Drives Footprint Type Design fl d Drive Filter Current L X d price up to R88D T02 R88A FI 104E M R88D A04 R88A FI 107E M R88D A08 R88A FI 115E M R88D A15 R88A FI 125E M R88D T05F to R88A FI 4006E M R88D T15F R88D T20F R88A FI 4010E M R88D T30F (9) (888) 88-SOURCE

11 PFO Motor Cable Chokes X Ø m L Output Choke motor D L X m price k (mm) (mm) (mm) (euro) 3G3IV PFO OC/ G3IV PFO OC/ G3IV PFO OC/ G3IV PFO OC/4 > The PFO output chokes can be used in conjunction with the filters to improve EMC performance. They are especially effective where radiated emissions from long drive to motor cables are a problem e.g. corruption of near by control or data cable signals or radio / television interference. The correct fitting of a PFO choke into the motor cable can eliminate these problems. The table above gives approximate motor k ratings for the chokes but the selection is ultimately governed by the type and thickness of motor cable fitted i.e. the motor cable must fit through the PFO choke centre hole. Occasionally EMC problems will occur within an installation when components in the same wiring enclosure affect one another, for example, open control boards may corrupt low level sensor signals. Usually in these cases the fitting of additional chokes into the control and sensor cables will cure the problem - a small amount of experimentation may be required to determine the optimum configuration of these additional chokes. (10) (888) 88-SOURCE

12 Footprint Type EMC Filter Installation Recommendations TO CONFORM TO TE EMC DIRECTIVE, IT IS NECESSAR TAT TESE INSTRUCTIONS BE FOLLOED AS CLOSEL AS POSSIBLE. FOLLO TE USUAL SAFET PROCEDURES EN ORKING IT ELECTRICAL EQUIPMENT. ALL ELECTRICAL CONNECTIONS TO TE FILTER, INVERTER & MOTOR MUST BE MADE B A QUALIFIED ELECTRICAL TECNICIAN. 1) Check the filter rating label to ensure that the current, voltage rating and part number are correct. 2) For best results the filter should be fitted as closely as possible to the incoming mains supply of the wiring enclosure, usually directly after the enclosures circuit breaker or supply switch. 3) The back panel of the wiring cabinet of board should be prepared for the mounting dimensions of the filter. Care should be taken to remove any paint etc. from the mounting holes and face area of the panel to ensure the best possible earthing of the filter. 4) Mount the filter securely. Mount the inverter on top of the filter using the mounting screws provided. 5) Connect the mains supply to the filter terminals marked LINE, connect any earth cables to the earth stud provided. Connect the filter terminals marked LOAD to the mains input of the inverter using short lengths of appropriate gauge cable (Some filter models are preleaded). 6) Connect the motor and fit any PFO chokes required, as close to the inverter as possible. Armoured or screened cable should be used with the 3 phase conductors only threaded twice through the centre of the Ferrite Core. The earth conductor should be securely earthed at both inverter and motor ends. The screen should be connected to the enclosure body via an earthed cable gland. 7) Connect any control cables as instructed in the inverter instruction manual. IT IS IMPORTANT TAT ALL LEAD LENGTS ARE KEPT AS SORT AS POSSIBLE AND TAT INCOMING MAINS AND OUTGOING MOTOR CABLES ARE KEPT ELL SEPARATED. iring Panel Enclosure Supply cable gland Breakers, Switches, Etc PLC, control gear, Etc Inverter Phase conductors only through PFO choke - not earth conductor or screen Screen earthed to metal cable gland Motor Filter Backplate Bonded Earth E Screened Motor Cable (11) (888) 88-SOURCE

13 Standard Type EMC Filter Installation Recommendations TO CONFORM TO TE EMC DIRECTIVE, IT IS NECESSAR TAT TESE INSTRUCTIONS BE FOLLOED AS CLOSEL AS POSSIBLE. FOLLO TE USUAL SAFET PROCEDURES EN ORKING IT ELECTRICAL EQUIPMENT. ALL ELECTRICAL CONNECTIONS TO TE FILTER, INVERTER & MOTOR MUST BE MADE B A QUALIFIED ELECTRICAL TECNICIAN. 1) Check the filter rating label to ensure that the current, voltage rating and part number are correct. 2) For best results the filter should be fitted as closely as possible to the incoming mains supply of the wiring enclosure, usually directly after the enclosures circuit breaker or supply switch. 3) The back panel of the wiring cabinet of board should be prepared for the mounting dimensions of the filter. Care should be taken to remove any paint etc. from the mounting holes and face area of the panel to ensure the best possible earthing of the filter. 4) Mount the filter securely. 5) Connect the mains supply to the filter terminals marked LINE, connect any earth cables to the earth stud provided. Connect the filter terminals marked LOAD to the mains input of the inverter using short lengths of appropriate gauge cable. 6) Connect the motor and fit any PFO chokes required, as close to the inverter as possible. Armoured or screened cable should be used with the 3 phase conductors only threaded twice through the centre of the Ferrite Core. The earth conductor should be securely earthed at both inverter and motor ends. The screen should be connected to the enclosure body via an earthed cable gland. 7) Connect any control cables as instructed in the inverter instruction manual. IT IS IMPORTANT TAT ALL LEAD LENGTS ARE KEPT AS SORT AS POSSIBLE AND TAT INCOMING MAINS AND OUTGOING MOTOR CABLES ARE KEPT ELL SEPARATED. iring Panel Enclosure Supply cable gland Breaker, Isolator, Etc PLC, control gear, Etc Phase conductors only through PFO choke - not earth conductor or screen Screen earthed to metal cable gland Motor L1,L2,L3 Filter E Backplate Bonded Earth Inverter Screened Motor Cable In the interest of product improvement, specifications are subject to change without notice. LEADERS IN FACTOR AUTOMATION (12) (888) 88-SOURCE

14 is your source for quality new and certified-used/pre-owned equipment FAST SIPPING AND DELIVER TENS OF TOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS UNDREDS OF MANUFACTURERS SUPPORTED LEASING/MONTL RENTALS ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center SM InstraView REMOTE INSPECTION Remotely inspect equipment before purchasing with our interactive website at Contact us (888) 88-SOURCE E BU USED EQUIPMENT Sell your excess, underutilized, and idle used equipment e also offer credit for buy-backs and trade-ins /ebuyequipment LOOKING FOR MORE INFORMATION? Visit us on the web at for more information on price quotations, drivers, technical specifications, manuals, and documentation