PRODUCT INFORMATION. Electro Hydraulik Actuator High Pressure PA Low Pressure PANDA
|
|
- Aldous Evans
- 5 years ago
- Views:
Transcription
1 PRODUCT INFORMATION Electro Hydraulik Actuator High Pressure PA Low Pressure PANDA
2 Product description We developed a new generation of electro hydraulic valve actuators to offer an alternative product to electric and pneumatic actuators. Our actuators are compact, reliable, simple to install and operate and we can offer a competitive priceperformance ratio. We offer on/off, as well as modulating actuators. Fail safe function is available for any type. Usually, the control of our actuators are taken over by the process control. The actuator only need power supply in a range from 24VDC to 400VAC. For spring return actuators, a solenoid valve keeps the actuator in position. For double acting actuators, we supply reversible hydraulic pumps and motors. The simply design allows us to keep prices very low. All actuators are available with complete control cabinet and modulating software. The major advantage of hydraulic drive engineering are a very good efficiency factor and a high power density. Very high output power can be realized with little input power. The reason are the direct connection between pump and hydraulic cylinder. Due to the fact of permanent oil wetting of most wear parts, the actuators run nearly free of wear out. For operation in case of power failure, a hydraulic system offers easy ways to store the energy for emergency cases. Spring return actuators or the usage of pressure accumulator are available. We are oriented towards norms and directives as: ATEX 94/9/EG Non electrical devices in EX areas DIN EN Directive 2006/42/EG Safety for machinery EN ISO 10 Safety for hydraulic systems EN ISO 4413 Functional safety DIN EN Quality management according to ISO 9001: 2008 KTC Systemtechnik GmbH Adlerhorst Hamburg
3 Product Selection PartTurnAktuator low pressure Type: PANDA PANDA Control O M Open/Close EX ATEX Certified Modulating S2 SIL 2 certified EB Limit Switch Box PM Potentiometer OB On Board Control box (On/Off or Modulating) Torque Nm 102/77 69/44 E15 152/118 94/60 E20 245/ /98 E50 371/ / /509 Double Acting Torque Nm Open/Close 0 /90 Close (Spring) 90 /0 E10 E40 Special Version Open (hydr.) 0 /90 E30 Single Acting Spring Return D10 46 D15 93 D D D D D D D /126 Combination available Connection D D L L DS DS 157/98 399/269 D L DS E60 846/ /379 E / /510 E / /865 D E / /1309 D Range E / /1754 D E / /2207 D E / /4068 D Other torque available on request adjustable
4 Technical Data PartTurnAktuator low pressure Type: PANDA Motor Voltage: 400 V 50/60Hz / 230V 50Hz Power consumption: 180W bis 250W Solenoid Valve: 24VDC / 230V 50Hz On Board pressure pmax.: 8,0bar Speed: adjustable by throttle Medium: Hydraulic oil HLP, filtered min. 10µm Ambient Temp.: 20 C...50 C Harzadous Areas: Zone 1 and 2 Valve Connections D Dimensions (mm) A B Standard C Oil (L) Flange ISO 5211 Connection SW x depht D ,3 F05/F07 DS 14x16 D ,6 F05/F07 DS 14x18 E10/D /332 0,6 F05/F07 DS 17x19 E15/D /350 1,5 F07/F10 DS 17x24 E ,5 F07/F10 DS 22*30 E ,5 F07/F10 DS 22x34 Other Dimensions available on request Modulating Actuators may differ from above. L DS
5 Product Selection PartTurnAktuator high pressure Type: PA PA Special Version EX Exproof S2 SIL 2proof Control EB Limit Switch Box O Open/Close PM Potentiometer OB M Modulating On Board Control Box (ON/OFF or Modulating) Combination available Connection D D L L DS DS Single Acting Spring Return Torque Nm Open (hydr.) 0 /90 Close (Feder) 90 /0 See Page 6 E30 222/ /65 E40 451/ /256 E50 896/ /517 E60 0/ /1081 Further Torque available Double Acting Torque Nm Open/Close 0 /90 D D D Range adjustable D D
6 Technical Data PartturnAktuator high pressure Type: PA Motor Voltage: 400 V 50/60Hz / 230V 50Hz Power consumption: 180W bis 250W Solenoid Valve: 24VDC / 230V 50Hz On Board pressure pmax.: 180bar Speed: adjustable by throttle Medium: Hydraulic oil HLP, filtered min. 10µm Ambient Temp.: 20 C...50 C Harzadous Areas: Zone 1 and 2 Connection D Dimension (mm) A B Standard C Oil (L) Flange ISO 5211 Connection SW x depth E ,3 F10 DS 14x20 E ,3 F12 DS 22x35 E ,3 F12 DS 27x40 E ,0 F14 DS 36x40 Torque up to Nm available on request L DS
7 Schematic Diagram PartTurnAktuator low pressure Type: PANDA PartTurnAktuator high pressure Type: PA PANDAMD..90 Double Acting PANDAOE..90_EBOB Single Acting Open/Close PANDAOD..90 Double Acting NARMUR Platte mit NG6 Ventilanschluß NARMUR Platte Typ PA: 160bar 180bar Typ PA: 160bar 180bar Conrol Box optional Control Signal OPEN:M=1/V=1 Feddback Signal Open: M=0/V=1 ControlSignal OPEN: M=0/V=0 Feedback Signal Close: M=0/V=0 INPUT: Open/Close 24VDC / 230VAC OUTPUT: Open/Close 24VDC / 230VAC 230V 50/60Hz 1phs 400V 50/60 Hz 3phs PANDA: Watt PA: Watt Simplified Schematic Diagram Typ PA: 160bar 180bar
8 Company Profile Company: KTC Systemtechnik GmbH Adlerhorst Hamburg Phone.: info@ktcsystemtechnik.de Founding: 2010 Products: Actuators for industrial Valves Electro hydraulic, linear (LA), 1/4turn (PA / PANDA), single / double acting Hydraulic Systems Complete hydraulic systems with control cabinets hardware and software Hydraulik cylinder Service: PLCProgramming Machine automation Machine repair Process optimization Process automation
Valve automation partner
Valve automation partner for actuation safety KTC-Systemtechnik your quality ex proof electro hydraulic valve automation compact actuators quarter turn or linear hydraulic station with actuators development
More information5/2 and 5/3 Way Valves
Caracteristics to VDI 9 Pressures quoted as gauge pressure Characteristics Symbol Unit Description General Features Ceramic Spool Valve Mounting On base plate, Tube connection Base plate Port size G1/
More information3/2 Way Valve G1/8. Data Sheet No E. Characteristics Symbol Unit Description General Features Spool valve.
AP64E00DX00X Characteristics to VDI 90 Pressures quoted as gauge pressure Characteristics Symbol Unit Description General Features Spool valve Mounting screws M Tube connection Thread Port size ; 7.4 deep
More informationE Range of Electro - Hydraulic Linear and Rotary Actuators. Technical Specification.
E Range of Electro - Hydraulic Linear and Rotary Actuators Technical Specification www.advanced-actuators.com Basic Design Concept Please note this brochure is purely an overview of our product range.
More informationPNEUMATIC ACTUATORS. Linear acting
PNEUMATIC ACTUATORS We supply pneumatic double-acting or single-acting with spring return. The actuators are mainly quarterturn actuators for butterflyvalves and ball valves or multiturn for gate valves
More informationCustomized ELECTRO-HYDRAULIC CONTROL SYSTEM
Customized ELECTRO-HYDRAULIC CONTROL SYSTEM ELECTRO-HYDRAULIC CONTROL SYSTEM 2 Since the founding of Automation Technology (ATI) more than 20 years ago, we have been recognized for innovation and dependability
More informationPressure Switches. Pressure switches, pneumatic. Pressure switches, electronic
Contents Description Page Pressure switches, pneumatic, with plug 50 Pressure switches, pneumatic, with flat pins 51 Pressure switches, pneumatic 52 55 with internal thread with flange connection Pressure
More informationSELF-CONTAINED ELECTRO-HYDRAUIC CONTROL SYSTEMS
SELF-CONTAINED ELECTRO-HYDRAUIC CONTROL SYSTEMS COMPANY For over 30 years Paladon Systems has been supplying valve actuators and control systems on a global basis. Since its inception in 1981, Paladon
More informationActuated Valves. Product Information
Actuated Valves Product Information HQ4 & HQ6 HQ Electric Actuator for Albion Ball & Butterfly Valves Small, light and compact design High Output torque Alloy Gearing Multi Voltage Options Standard Specification
More informationDirectional Control Valve Series D1VW
Characteristics The NG6 directional control valve series D1VW provides high functional limits up to 8 l/min in combination with a very low, energy-saving pressure drop. A wide variety of spool options
More informationshort name: 3WL.IG* technical product sheet created :57 1/6 3-way ball valve F/F PN 63 with pneumatic actuator hard anodized aluminum
with pneumatic actuator hard anodized aluminum technical product sheet short name: 3WL.IG* 3-way ball valve F/F PN 63 E-Box MV Port Modell G Kugel Bauart RE06 RE06 1 1 1/ 1/ 3/" 1 1/ 1 1/ 3/" 1 1/ 1 1/
More informationQuarter turn actuators Index
Index General information page Introduction 227 Product information Pneumatic actuators page Double acting and spring return 228 page Index 231 ECON Compact 232 EL-series 234 ELQ-series 236 Hydraulic actuators
More informationProduct data sheet. Series 210, DN (2½ - 6 ) Ordering No PE
Series 210, DN 63 160 (2½ - 6 ) Ordering No. 210..-PE06-000. Manual actuator with hand lever Advantages Three sizes available: DN 63, 100, 160 with ISO-F flanges All vacuum parts made of stainless steel
More information2/2-way Diaphragm Valve with stainless steel design, weld end or clamp connection, DN 8-25
2/2-way Diaphragm Valve with stainless steel design, weld end or clamp connection, DN 8-25 Type 2103 can be combined with Hermetical separation of fl uids from the operating mechanism by diaphragm Zero
More informationQ u a r t e r T u r n E l e c t r i c A c t u a t o r s
Quarter Turn Electric Actuators A101/04 2 Q uarter-turn actuators are used to operate ball, plug or butterfly valves, dampers, vents and any equipment with quarter-turn or part turn travel. BERNARD has
More informationDirect mounting NAMUR solenoid valves for process valve actuators New Revolutionary Design- Worldwide Patents Pending
Direct mounting NAMUR solenoid valves for process valve actuators New Revolutionary Design- Worldwide Patents Pending The V-Solenoid II Standard Series ATEX EX Series Intrinsically Safe Series ExProof
More informationTechnical Data Sheet
Technical Data Sheet Type 52 2/2-way solenoid valve NC - Valve normally closed (as standard) NO - Valve normally open (as option) Direct operated piston design valve. No differential pressure is necessary
More informationPositioners Converters Limit Switches Position Transmitters Solenoid Valves Accessories. Selection and Application
Positioners Converters Limit Switches Position Transmitters Solenoid Valves Accessories Selection and Application Associated s T 8355 EN ff. Edition January 2010 Information Sheet T 8350 EN Positioners,
More informationRemote Process Actuation Control System AirLINE - Siemens ET 200S
Remote Process Actuation Control System AirLINE - Siemens ET 200S Type 8644 can be combined with... Fully compatible with Siemens ET 200S Combination of Fieldbus, pilot valves and I/O modules High flexibility
More informationAngle Seated Valves. ecoflo-as. Angle Seated Valves
Angle Seated Valves ecofloas Angle Seated Valves AngleSeat Valves PNEUMATIC AND ELECTRIC VALVES PN / PN / PN / ANSI 0 / ANSI 00 series pneumatic and electric valves are designed as onoff or reglation valves
More informationPEL power supplies. 24 Vdc 18 Vdc 12 Vdc SWITCHED MODE POWER SUPPLIES/ PEL SERIES
power supplies Our powerful miniature units ensure optimum power supply for miniature controllers. Versions with a 12, 18 and 24 V output voltage are available, enabling them to be used in a whole range
More information2/2-way Globe Valve for media up to +180 C, DN
2/2-way Globe Valve for media up to +180 C, DN 10-100 Compact globe valve version Flange, threaded and welded ports as standard Stainless steel 316L valve body Available with flow direction below and above
More informationRemote Process Actuation Control System AirLINE - Rockwell 1734 Point I/O System
Remote Process Actuation Control System AirLINE - Rockwell 1734 Type 8644 can be combined with... Fully compatible with Rockwell 1734 Point I/O System Combination of Fieldbus, pilot valves and I/O modules
More informationAS-I
Digital Positioner 8049 Compact digital positioner for pneumatic control valves. Positioner can be integrated into valve actuator (no external moving parts for stroke feedback) Wide range of strokes 3-8
More informationProportional directional valves type DHZO-AES and DKZOR-AES direct operated, without position transducer, ISO 4401 size 06 and 10
www.atos.com Table F60-8/E Proportional directional valves type DHZO-AES and DKZOR-AES direct operated, without position transducer, ISO 440 size 06 and 0 AES execution included in this table is available
More informationCOMPACT ACTUATORS COMPACT PNEUMATIC & HYDRAULIC ACTUATORS
COMPACT ACTUATORS COMPACT PNEUMATIC & HYDRAULIC ACTUATORS A WORLD OF EXPERIENCE Biffi is a leading manufacturer of valve automation solutions with 60 years experience and a global presence, offering a
More informationPneumatic-Motors Accessories catalog DMO - PMW pneumatic gearwheel motors and spur gear motors
Pneumatic-Motors Accessories catalog DMO - PMW pneumatic gearwheel motors and spur gear motors Dok.-Nr. M1-009 UK Contents accessories catalog Page 2 Designation... page Contents... 02 Ball valve PN 25...
More informationVersions. Version with K VS Version with K VS 2.0. Fig. 1: Type 3967 Solenoid Valve
Type 367 Solenoid Valve Application Solenoid valve for controlling pneumatic linear actuators with NAMUR rib according to IEC 60534 or pneumatic rotary actuators with NAMUR interface according to VDI/VDE
More informationProportional pressure reducing valves type DHRZO and DHRZA standard and ex-proof version, direct operated, ISO 4401 size 06
www.atos.com Table TF040-2/E Proportional pressure reducing valves type DHRZO and DHRZA standard and ex-proof version, direct operated, ISO 4401 size 06 A B DHRZO-A-012/25 A B DHRZA-A-010/25 DHRZ* are
More informationBALL VALVE - 10 SERIES Electric actuator - El-O-Matic
DN B C D BALL VALVE - 10 SERIES Electric actuator - El-O-Matic E L DIMENSIONS: (mm) DN Ø L B C EL D E Kg 10 3/8" 36 33 73 55 298 95 7,8 15 1/2" 36 33 73 55 298 95 7,8 20 3/4" 39 36 76 55 301 95 8,3 25
More informationVALVITALIA VALVE OPERATORS
A Long Experience in Energy Equipment and one Goal: The Customer s satisfaction. VALVITALIA VALVE OPERATORS 1 VALVITALIA AUTOMATION DIVISION PROFILE Valvitalia Automation Division manufactures all type
More information3/2-Way Motor Control Valve 7382 DN 15 up to DN 50
3/2-Way Motor Control Valve 7382 15 up to 50 Fast and high resolution motorvalve for control and switching of neutral through to highly aggressive media in process engineering, chemical industries and
More informationELECTRO-HYDRAULIC ACTUATION SYSTEMS
ELECTRO-HYDRAULIC ACTUATION SYSTEMS ELECTRO HYDRAULIC ACTUATION SYSTEMS COMBINING TECHNOLOGIES OF ELECTRIC AND HYDRAULIC ACTUATORS Biffi Electro-Hydraulic actuators combine the simplicity and lower infrastructure
More informationElectronic Limit Switch Type
Electronic Limit Switch Type 3738-20 with optional solenoid valve for on/off rotary actuators Application Electronic limit switch for on/off applications to indicate the end position of rotary actuators.
More informationRack & Pinion Pneumatic Actuators SPRING RETURN DOUBLE ACTING
Rack & Pinion Pneumatic Actuators SPRING RETURN DOUBLE ACTING Proven quality since 1892 Econosto, part of the ERIKS group, has been offering a wide variety of engineered products since 1892. By focusing
More informationChapter 6: Check Valves
Contents Chapter : Check Valves Series Description Size Mounting Page Parker Standard DIN / ISO 1/8 1/4 3/8 1/2 3/4 1 0 10 1 25 32 Subplate Screw-in Slip-in Shuttle valves SSR -2 Check valves, direct operated
More information2/2-way Angle-Seat Valve for medium up to +180 C, threaded port connection, DN 15-65
2/2-way Angle-Seat Valve for medium up to +180 C, threaded port connection, DN 15-65 Type 2000 can be combined with High flow rate Long life cycle NC and NO universal s with modular universal accessory
More informationRUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a bi-directional wafer valve equipped with two metallic coved rubber sleeves designed for use in the handling of abrasive slurries, mainly in industries
More informationChapter 11: Valves and Actuators with the NAMUR-interface
Right of authorship: the content of the training (wording, drawings, pictures) are owned by the author. Any utilization except for individual use is allowed only after permission of the author. Valves
More informationMagnetic Field Sensor for pneumatic cylinders BIM-UNT-AY1X/S1139
ATEX category II 1 G, Ex Zone 0 ATEX category II 1 D, Ex Zone 20 For T-groove cylinders without mounting accessories Optional accessories for mounting on other cylindrical housings. One-hand mounting possible
More informationContents. FieldQ. FieldQ. Product data sheet Rev. 0 October FieldQ Valve Actuator 2. FieldQ Actuator Torque 4
1.601.00 Rev. 0 Contents Valve Actuator General Overview... Actuator Torque 4 Double Acting Actuators.. - Nm...4 Spring Return Actuators... - Nm...5 Spring Return Actuators... - lbf.in...6 Valve Actuator
More informationmass flowmeter for compressed air
mass flowmeter for compressed air VARIOMASS ECO pressure and temperature compensated easy and cost effective installation of the sensor no pressure loss caused by the sensor no moving parts, i.e. maintenance
More informationChapter 6: Check Valves
Contents Chapter : Check Valves Series Description Size Mounting Page Parker Standard DIN / ISO 1/8 1/4 3/8 1/2 3/4 1 0 10 1 25 32 Subplate Screw-in Slip-in SSR RK / RB CS SPZBE SPV / SPZ C4V CPS C4V D4S
More informationAngle Seat Control Valve 7020
Angle Seat Control Valve 72 DN 8 up to DN 8 PN 4 Pneumatically operated control valves for neutral through to highly aggressive media. Integrated positioner Compact design All parts contacting the fluid
More informationSBA Accumulator Safety Blocks
Overview Introduction For working pressures up to 350 Bar (5075 PSI) IN THIS SECTION Overview 85 Technical Data 87 Models & Dimensions SBA10 89 SBA20 90 SBA32 91 SBAT3L 92 SBAT3P 93 Adapters 94 Ordering
More informationFIELDBUS ELECTRONICS 580 Electronics (Series : M7 to 1/2 (G or NPT) or with push-in fittings Ø4 to 10 mm)
FIELDBUS ELECTRONICS 580 Electronics (Series - : M7 to 1/2 (G or NPT) or with push-in fittings Ø4 to 10 mm) 580 Fieldbus - Electronics Made Easy! Innovative Graphic Display is used for easy commissioning,
More informationHigh Flow Valve Actuation Range. NAMUR Valves G1/4" & G1/2" Piped Valves G1/4" & G1/2" Banjo Valves G1/8" & G1/4"
31-37 High flow NAMUR valves G1/ and G1/ aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding High Flow Valve Actuation
More informationV200 Positioner. V200 P Pneumatic Positioner. V200 E Electropneumatic Positioner. Housing Material: Cast aluminium with polyester coating
V200 Positioner Housing Material: Cast aluminium with polyester coating Indicator Options: Flat pointed indicator or raised indicator (red/green or yellow/black) One housing for pneumatic or electropneumatic
More informationRack & Pinion Pneumatic Actuators Spring return - Double acting
Rack & Pinion Pneumatic Actuators Spring return - Double acting Rack & Pinion pneumatic actuators The Econ Rack & Pinion pneumatic actuators are designed for use in quarter-turn applications and are ideal
More informationHigh Pressure Filter Pi 4230
High Pressure Filter 4230 Nominal pressure 315 bar (4570 psi), nominal size 160 to 400 according DIN 24550 1. Features High performance filters for modern hydraulic systems Modular system Compact design
More informationVALVCON ADC-SERIES ELECTRIC ACTUATOR WITH OPTIONAL BATTERY BACK-UP POWER
VALVCON ADC-SERIES ELECTRIC ACTUATOR WITH OPTIONAL BATTERY BACK-UP POWER Metso is a leading designer and provider of Valvcon compact, reliable, electronically controlled electric actuators for valves and
More informationSeries 26d Ball Valve
Stainless Steel Series 26d Ball Valve Application Tight-closing ball valve made of stainless steel for corrosive media, especially to meet high process requirements in chemical plants: Nominal sizes DN
More information3/2-way and 2 x 3/2-way Solenoid Valve for pneumatics
654 3/-way and x 3/-way Solenoid Valve for pneumatics Compact design Single and manifold mounting Low power consumption Fast response times Space saving ( x 3/-way version) Type 654 can be combined with...
More informationTemposonics. M-Series Analogue / SIL2* Absolute, Non-Contact Position Sensors. Temposonics MH Measuring Length mm
Temposonics Absolute, Non-Contact Position Sensors M-Series / SIL2* Temposonics MH Measuring Length 50-2500 mm Compact Sensor for Mobile Hydraulics Linear, absolute Measurement in Hydraulic Cylinders Non-Contact
More informationMANUFACTORING APPLICATIONS. 90 pivoting angle All versions for Ex Zone I Ambient temperature -60 C to +80 C Initial torque of up to 350,000 Nm
SCHUCK ACTUATORS AND CONTROL SYSTEMS TYPE SST Flexible actuator and control system for 90 travel with Scotch-yoke principle for torques ranges up to 350,000 Nm. 02.2011 EN TK 002 1 WWW.SCHUCK-ACTUATOR.COM
More informationAS-I
Digital Positioner 8049 Compact digital positioner for pneumatic control valves. Positioner can be integrated into valve actuator (no external moving parts for stroke feedback) Wide range of strokes 3-8
More informationV200 Series Positioners
V200 Series Positioners In a single compact and rugged housing The V200 positioner incorporates the flexibility of converting from a pneumatic unit to several versions of an electropneumatic unit, and
More informationChapter 2: Directional Control Valves
Contents Chapter : Directional Control Valves Series Description Direct operated Pilot operated Page DIN / ISO 06 10 16 5 3 10 16 5 3 Seat valves, electrically operated D1SE - Spool valves, electrically
More informationHYDAC (Three-Phase Current) Compact Power Units CO1
HYDAC (Three-Phase Current) Compact Power Units CO1 Up to 250 bar Up to 20 l/min In accordance with EN 60034-1 suitable for: Short-term operation: S2 = 5 min* (average value) Intermittent operation: S3
More informationAirLINE and AirLINE Quick electrical/pneumatic Automation System
AirLINE and AirLINE Quick electrical/pneumatic Automation System Type 8644 can be combined with Fully compatible with Rockwell Combination of Fieldbus, pilot valves and I/O modules higher fl exibility
More information3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics
/2-, 5/2-5/-way Solenoid Valves for process pneumatics Type 658 stard High flow-rate capacity Reduced power consumption Single or manifold mounting stard Type 658/659 can be combined with... Stard-, EEx
More informationPROCESS & AUTOMATED VALVES
Process & utomated Valves HYDC s line of Process and utomated Valves complements our isolation valve knowhow and ability to supply high quality solutions to your valve requirements. 3-1 HV Series Inline
More informationSicher und flexibel die neue Antriebsgeneration actubar
A Module of the Valve-Control System bar-vacotrol -positurn2 Sicher und flexibel die neue Antriebsgeneration actubar Positioner and 3-position control unit for part-turn actuators Objective Function bar-positurn2
More informationElectrical actuator for industrial applications
Stellantriebe Electrical actuator for industrial applications Available in The Allrounder Compact and robust Classic actuator technology With the Nano+ series ARIS offers a new generation of robust actuators
More informationIntelligent Positioner
Intelligent Positioner Construction The GEMÜ 1 µpos is a digital electro-pneumatic positioner for process valve control. Designed for simple, safe and quick use with valves with strokes < mm. The positioner,
More information+GF+ PNEUMATIC ACTUATED BALL VALVE +GF+ PNEUMATIC ACTUATED BALL VALVE +GF+ PNEUMATIC ACTUATED BALL VALVE 3-16
+GF+ PNEUMATIC ACTUATED BALL VALVE Type 21/2 2-way True Union Pneumatically actuated ball valve for aggressive fluids and industrial applications. Based on the new Type 546 ball valve, the Type 21-2 uses
More information2/2- and 3/2-way Ball Valve with pneumatic rotary actuator, plastic body, DN 10-50
/- and 3/-way Ball Valve with pneumatic rotary actuator, plastic body, DN -50 Radially expandable body Pneumatic actuator in compact model Optical position indicator Control valve acc. to NAMUR Type 5
More informationE J3-Series. Electric quarterturn / partturn actuators. ASC Armaturen GmbH - D Popelau
E J-Series Electric quarterturn / partturn actuators ASC Armaturen GmbH - D 97 Popelau phone.: +49/884/68-0 Fax: +49/884/68- e-mail: info@ascarmaturen.de www.ascarmaturen.de ISO-Interface Optical function
More informationACTUATION SOLUTIONS EXPERIENCE MORE
ACTUATION SOLUTIONS EXPERIENCE MORE Maximize your plant s safety with the most advanced technology Overcome your most demanding automation challenges with our smart and reliable valve automation solutions
More information2/2-way Diaphragm Valve, forged valve body, weld end and clamp connection, DN 8-100
2/2-way Diaphragm Valve, forged valve body, weld end and clamp, DN 8-100 Type 2031 with weld end Type 2031 can be combined with Type 2031 with clamp Hermetical separation of fluids from the operating mechanism
More informationIntegrated Control modules
.60.0 Rev. 0 Page of 9 Integrated Control modules QC, QC2 and QC Features: - Basic actuator functions for: - Spring return applications, or - Double acting applications or, - Double acting Fail in Last
More informationGeneral Specifications DRV DRV-Exm DRV-Exd
direct operated, 3-way pressure reducing valve Q max = 8 l/min pressure range = - 5 bar body stainless steel (optional) Description The proportional pressure reducing valve (3-way function) is used to
More informationRUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a bi-directional wafer valve equipped with two metallic coved rubber sleeves designed for use in the handling of abrasive slurries, mainly in industries
More information3/2-way Solenoid Valve for pneumatics
656 3/-way Solenoid Valve for pneumatics Compact design Single and manifold mounting Low power consumption Rocker pilot in DC Type 656 can be combined with... Fast response times Type 506 Type 510/511
More information2 x 3/2 Way Valves Series S10
x / Way Valves Series S0 G/ and -In Connections OD 6 mm Actuation systems: Pneumatic Electrical pilot actuated Versions: x normally closed x normally open x normally closed and x normally open With external
More informationDigital Positioner 8049
Compact digital positioner for pneumatic control valves. Positioner can be integrated into valve actuator (no external moving parts for stroke feedback) Wide range of strokes 0. to. inches ( 8 mm) No steadystate
More informationActuators & Positioners Pneumatic Actuators Series UP1/2/3/4/5/6
Data Sheet Actuators & Positioners Pneumatic Actuators Series UP1/2/3/4/5/6 Wide Range of Torque Ratings - Six actuator sizes available in ratings from 122 to 6372 Newton meters (90 to 4700 foot-pounds)
More information3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics
/-, 5/- 5/-way Solenoid Valves for process pneumatics Type 658 stard High flow-rate capacity Reduced power consumption Single or manifold mounting stard Type 658/659 can be combined with... Stard-, EEx
More informationElectric Actuator EQ Series
Electric Actuator EQ Series Engineering Creative Solutions for Fluid Systems Since 1901 INTRODUCTION Pratt Industrial designs and provides high quality actuators and services related to valve automation.
More informationOperating Instructions. Angle Seat Control Valve. Type 7020
Operating Instructions Angle Seat Control Valve Type 7020 With: Digital Positioner Type 8048 Electro-pneumatic Positioner Type 8047 Pneumatic Positioner Type 8047 Version: 02/2006 Manual-7020e.doc Art.-No:
More informationPower Conversion Systems 2005/2006. Schaefer the Power to make it happen.
Power Conversion Systems 2005/2006 Schaefer the Power to make it happen. Company profile workforce experience customer orientation flexibility reliability Schaefer Elektronik, founded in 1969, has grown
More informationDigital Positioner 8049
Compact digital positioner for pneumatic control valves. Positioner can be integrated into valve actuator (no external moving parts for stroke feedback) Wide range of strokes 0. to. inches ( 8 mm) No steadystate
More informationMAQ Series Electric Actuator
Series Electric Actuator Series INTRODUCTION KEYVALVE designs, produces and provides high quality actuators and services related to valve automation. - Our long years experience in automation field enables
More information2/2-way ball valve with electric rotary actuator, ball valve in stainless steel, DN 10-65
2/2-way ball valve with electric rotary actuator, ball valve in stainless steel, 10-65 Suitable for aggressive media High flow rate value -piece Actuator with adjustable limit switches 2-piece Visual position
More informationValve bank type BA to allow combination of various different directional valves with connection hole pattern NG 6 conforming DIN A6
Valve bank type BA to allow combination of various different directional valves with connection hole pattern NG 6 conforming DIN 24 340-A6 Flow Q max = approx. 25 lpm Pressure p max = approx. 400 bar (dependent
More informationAir Operated 3 Way Brass Ball Valve
Type: PA1302 Type: PA1312 Type: PA1322 Pneumatic actuator direct mounted Actuator fitted via mounting kit Actuator fitted via stem extension Pneumatic Actuator features: Rack and pinion construction Hard
More informationAutomation Capabilities
Crane Valves North America Automation Capabilities Summary of Capabilities Automation Crane Valves North America provides a variety of valve automation products, including pneumatic and electric actuators,
More information3/2-way and 2 x 3/2-way Rocker Solenoid Valve for pneumatics
65 /-way and x /-way Rocker Solenoid Valve for pneumatics Type 65 can be combined with... Compact design Single and manifold mounting Low power consumption Rocker pilot in DC Fast response times Space
More informationButterfly valves Plastic and Metal
Butterfly valves Plastic and Metal Product overview and technical data VALVES, MEASUREMENT AND CONTROL SYSTEMS Innovative technology GEMÜ is a leading world-wide manufacturer of high quality valves, measurement
More informationProcess Analyzer. Cold Filter Plugging Point Process Analyzer CFPP-4. Credible Solutions for the Oil and Gas Industry
Process Analyzer Cold Filter Plugging Point Process Analyzer CFPP-4 Credible Solutions for the Oil and Gas Industry Cold Filter Plugging Point Process Analyzer Analyzer CFPP-4 To remain competitive, today
More informationEEX Line Spring-applied single-disc brake for potentially explosion hazardous areas
EEX Line Spring-applied single-disc brake for potentially explosion hazardous areas EEX Line Standard EEX Line (+50 C) / EEX Line (+60 C) EEX Line / IEC Ex EEX Line / U.S. (NEC 500/505) CSA EEX Line Industrial
More informationPilot Operated Proportional DC Valve Series D*1FW / D*1FT
Characteristics The D*1FW / D*1FT pilot-operated proportional DC valves are available in NG10 (CETOP5), NG16 (CETOP7) and NG25 (CETOP8). These valves (D*1FW) are controlled electrically with the external
More informationPOWER TRANSMISSION. Product range
POWER TRANSMISSION Product range Product range Business Unit Power Transmission Since the firm was established in 1911 by Wilhelm Binder, the Power of Magnetism has always been the essential principle
More informationCONTROL VALVE ACCESSORIES CVA : 0611 ELECTRO PNEUMATIC / PNEUMATIC POSITIONER POSITION TRANSMITTER SIL
ELECTRO PNEUMATIC / PNEUMATIC POSITIONER POSITION TRANSMITTER CVA : 0611 SIL Next generation of Positioner design featuring better performance and ease of setup has taken ELECTRO-PNEUMATIC POSITIONER RTX1000
More informationOil & gas, petrochemicals and chemicals
Oil & gas, petrochemicals and chemicals You are looking for a partner who understands your objectives. You require more efficient production facilities. We are your solution for process automation. Your
More informationAir Operated 3 Way Stainless Steel Ball Valve
Available with actuator function: DOUBLE ACTING, SINGLE ACTING (Failsafe), MODULATING (with optional positioner) Type: 2300R Type: 2310R Type: 2320R Pneumatic actuator direct mounted Actuator fitted via
More informationType 2511/12. Type Type 2030 Cable plug. ASI cable plug. Dosing control. General technical data Orifice Type 6518
3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics Type 658 standard standard High flow-rate capacity Reduced power consumption Single or manifold mounting Standard-, EEx m and EEx i versions
More informationPNEUMATIC ACTUATORS RACK AND PINION
The art of power and perfection PNEUMATIC ACTUATORS RACK AND PINION The art of power and perfection ACTREG, established in 1992, is a multinational company specializing in the manufacture and sales of
More informationAPS & APIS ATEX AIRPOWER SWITCH BOXES FEATURES DESCRIPTION
page 1 DESCRIPTION The switch boxes are suitable for rotary actuators and are the industry leader in versatility, quality and approvals gained. Models include APS standard range with a variety of outputs
More informationOptimise your temperature control
Optimise your temperature control Fast response, low pressure drop valves for tighter temperature control 3-Way Temperature Control Valve - Model G Overview Introducing the Model G 3-Way Temperature Control
More information