Lithium-Ion Multi Head Tool

Transcription

1 Lithium-Ion Multi Head Tool 12V Instruction Manual 3 Year Replacement Warranty MTC-0123 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. To view the full range visit:

2 Specifications - model no. MTC-0123 Multi Head Tool Input Power: Charge time: No load speed: Batteries: Weight: 12V 3-5 hours 0-15,000/min 2 x 12V, 3Ah Lithium-Ion Batteries 0.65kg Multi Function Head No Load Speed: 0-15,000/min Oscilating Angle: 45 Weight: 0.25kg Right Angle Drill Head No Load Speed: 0-400/min Chuck: 10mm Keyless Weight: 0.65kg Wrench Ratchet Head No Load Speed: 0-200/min Drive: 6.35mm ( 1 / 4 ) Max Torque: 14Nm Weight: 0.40kg Multi Cutter Head No Load Speed: 0-400/min Weight: 0.55kg

3 KNOW your Product Head attachment lock 12V Li-ion battery 3. Battery release button 4. Forward/ reverse selector 5. Variable speed trigger 6. LED light 7. Charging adaptor 8. Charging jack 9. Charging cradle Multi Function Head 10. Accessory drive spindle Multi Function Head Accessories 1 Hook & loop sanding pad 1 Straight saw blade 13. Scraper blade 14. Sanding paper 15. Accessory fixing washer 16. Locking bolt 17. Hex key Right Angle Drill Head mm Keyless chuck 19. 3mm Drill bit 20. 4mm Drill bit 2 5mm Drill bit 2 Double-ended screwdriver bit 23. S2 square bit Wrench Ratchet Head mm ( 1 /4 ) Square drive 25. Ratchet forward/reverse selector 26. 8mm Socket mm Socket Multi Cutter Head 28. Cutter guide 29. Blade guard

4 TABLE OF CONTENTS SPECIFICATIONS... Page 2 KNOW YOUR PRODUCT... Page 3 INTRODUCTION. Page 5 ELECTRICAL SAFETY. Page 5 GENERAL POWER TOOL SAFETY WARNINGS Page 6 BATTERY & CHARGER SAFETY WARNINGS... Page 8 LITHIUM BATTERY & CHARGER SAFETY FEATURES.. Page 10 ADDITIONAL SAFETY WARNINGS FOR MULTI HEAD TOOLS... Page 11 CHARGING THE BATTERY... Page 12 PREPARATION & SETUP... Page 13 MULTI HEAD TOOL OPERATION... Page 16 MAINTENANCE.. Page 21 SPARE PARTS.... Page 21 DESCRIPTION OF SYMBOLS.. Page 22 PACK CONTENTS. Page 22 WARRANTY.. Page 23

5 INTRODUCTION Congratulations on purchasing an Ozito 12V Multi Head Tool. We aim to provide quality tools at an affordable price. We hope you will enjoy using this tool for many years. Your Multi Head Tool MTC-0123 has been designed for general purpose drilling, screwdriving, cutting, sanding and chiseling around the home and is intended for DIY use only. electrical safety WARNING! When using mains-powered equipment, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage. Read and understand the manual prior to operating this tool. Save these instructions and other documents supplied with this tool for future reference. This tool is double insulated in accordance with AS/NZS ; therefore no earth wire is required. If the supply cord is damaged, it must be replaced by a qualified electrician or a power tool repairer in order to avoid a hazard. Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool. Using an Extension Lead Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock. It is recommended that the extension lead is a maximum of 25m in length. Do not use multiple extension leads

6 general Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term power tool in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

7 general Power Tool Safety Warnings f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dustrelated hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. b) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

8 BATTERY & CHARGER Safety Warnings THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY CHARGER. WARNING! If the battery pack case is cracked or damaged, do not insert it into charger. There is a danger of electric shock or electrocution. WARNING! Do not allow any liquid to get inside charger. Electric shock may result. To facilitate cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer. Before using the charger read all instructions and cautionary markings on the charger, battery pack and the product using the battery pack. This charger is not intended for any uses other than charging rechargeable batteries. Any other use may result in risk of fire, electric shock or electrocution. Do not place any object on top of the charger or place the charger on a soft surface that may result in excessive internal heat. Place the charger in a position away from any heat source. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in the risk of fire, electric shock or electrocution. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Have it checked by an electrician or power tool repairer. Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire. To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning. Removing the battery pack will not reduce this risk. Never attempt to connect 2 chargers together. DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed 40ºC (such as inside sheds or metal buildings in summer). The charger is designed to operate on standard household electrical power (240 volts). Do not attempt to use it on any other voltage! The battery pack is not fully charged out of the carton. First read the safety instructions and then follow the charging notes and procedures.

9 BATTERY & CHARGER Safety Warnings The longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 18-24ºC. Do not charge the battery pack in an air temperature below 10ºC or above 40ºC. This is important and will prevent damage to the battery pack. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery can explode in a fire. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, immediately discontinue use and do not recharge. During charging, the battery must be placed in a well ventilated area

10 lithium battery and charger safety features Over Charging Protection This feature ensures that the battery is never overcharged. When the battery has reached it s full charge capacity the charger will shut off protecting the internal components of the battery from being damaged. Over Discharge Protection An internal component of the battery pack is an over discharge protector. This feature will stop the battery from discharging beyond the recommended lowest safety voltage. Over Heat Protection The battery has an internal thermister cut off sensor which will cease the charging cycle if the battery becomes hot during the charging process. This thermister sensor will also stop the battery from operating should the battery become too hot during the operation of the tool. This can happen when the tool is overloaded or being used for extended periods of time. Up to 30min in cooling time may be required depending on ambient temperature and the operation being performed. Over Current Protection Should the battery be overloaded and the maximum current draw be exceeded the battery will temporarily stop working to protect the internal components. The battery will resume normal operation once the excessive current draw has returned to a normal level. This may take a few seconds. Short Circuit Protection If the battery pack was to short circuit the short circuit protector would immediately stop the battery pack from operating. This will prevent further internal components of the battery or the tools becoming damaged. 10

11 Additional Safety WarningS for Multi Head ToolS This tool is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the applicance by a person responsible for their safety. Recommendations for the use of a residual current device with a rated residual current of 30mA or less. Do not use the Multi Head Tool in wet or damp conditions. Always keep the work area free of tripping hazards. When using the Multi Head Tool always ensure you are wearing protective safety equipment including safety glasses/goggles, ear muffs, dust mask and other protective clothing including gloves and apron. Always check the work piece before operation and remove any obstructions such as nails, staples, screws, string, rags, cloths and other debris. Always use clamps or a vice to hold down and secure the work piece. Before drilling ensure there is a suitable gap below the work piece to prevent the drill bit from touching any obstacles. Before drilling holes or screwing into walls ensure that you are not breaking into any electricity, gas or water supply line, etc. Never change the direction of the chuck rotation while the tool is still running. Ensure the chuck has come to a complete stop before changing the rotation of the drill. Do not lay the tool down unless the tool is switched off and the chuck has come to a complete stop. Keep hands and other body parts well away from the work area whilst the tool is in use. Keep hand well away from the under side of the work piece during use. Do not use your hand to remove any dust, chips or other waste while the tool is in use. Do not touch the drill bit after operation. The bit can be HOT to touch and may cause burn injuries. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock. 11

12 CHARGING the BATTERY The multi head tool has been shipped in a low charge condition. Charging is required prior to use. Initial Charging Ensure that the charging cradle (9) is on a flat surface. Insert the charging jack (8) into the charging cradle (9). Plug the charging adaptor (7) into a power outlet. Insert the battery (2) into the charging cradle (9) (Fig. 1). The recess of the battery terminals will have a firm connection. Upon proper contact the red and green light will illuminate on the charging cradle (9). To obtain optimum battery performance and life, charge the batteries for 5-7 hours and use the tool until it runs down. Repeat this charge and discharge process approximately 4-5 times. Note: If the light on the charging cradle (9) fails to come on: Check the charging adaptor (7) is securely plugged into the wall outlet and is switched on. Check the charging jack (8) is securely connected to the charging cradle (9) socket. Check the battery (2) is firmly seated onto the charging cradle (9). Fig. 1 Normal Charging When the unit is on charge the red and green light will be on display. Charging starts automatically. The battery (2) will take 3-5 hours to charge. When the battery (2) is fully charged, the red light will go out, and only the green light will be on display. Remove the battery (2) from the charger after 5 hours. Important Charging Notes The charging adaptor (7) and battery (2) may become warm to touch while charging. This is normal, and does not indicate a problem. Use the charger at normal room temperature whenever possible. To prevent overheating, do not cover the charger and do not charge the battery (2) in direct sunlight or near heat sources. 12

13 preparation & set-up Attaching the Battery Caution: Ensure the variable speed trigger (5) is not depressed during insertion or removal of the battery (2). Insert the battery (2) into the battery recess in the multi head tool until it clicks into place (Fig. 2). Note: Do not use excessive force when inserting the battery (2). If the battery (2) does not slide in easily, it is not being inserted correctly. It is also possible that there could be damage to the battery (2), battery terminals and/or the multi head tool. If there is damage, have the complete tool checked by an electrician or power tool repairer. Removing the Battery Depress both battery release buttons (3) and remove the battery (2) from the multi head tool. Attaching the Tool Heads WARNING! Remove battery from the multi head tool before attempting to change accessories. Failure to do so may cause serious personal injury. Each of the heads attaches to the tool body in the same manner. Align the recesses on the tool body with the ridges on the tool head (Fig. 3). Push down until it sits flush on top of the tool body unit. Fig. 2 Fig. 3 Twist the tool head and you will hear a click as it locks into place (Fig. 4). Fig. 4 Note: Do not force the tool head onto the body unit as this may damage the tool. If it does not slide on easily, it has not been aligned properly. 13

14 preparation and set-up Removing the Tool Heads Slide the attachment lock (1) to the unlock position and hold. Twist the tool head and pull it away from the multi tool body. (Fig. 5) Fig. 5 Note: The symbol on the tool body indicates the correct direction to twist the head in order to unlock and remove it. (Fig. 6) Attaching Your Multi Function Head Accessory Fig. 6 WARNING! Remove battery from the multi head tool before attempting to change accessories. Failure to do so may cause serious personal injury Choose the desired angle required for your application. Position the perforated holes on the accessory over the locating pins on the accessory drive spindle (10) of the multi function head. Ensure the accessory is sitting flat against the face of the accessory drive spindle (10) (Fig. 7). Place the accessory fixing washer (15) in alignment with the inner hole of the accessory drive spindle (10). Fig. 7 Note: Ensure the flat side of the accessory fixing washer (15) is facing towards the accessory. 5. Insert the locking bolt (16) through the accessory fixing washer (15) and into the accessory drive spindle (10) of the Multi Function Tool. Hand tighten only. 14

15 preparation and set-up 6. Using the hex key (17), tighten the locking bolt (16) by rotating in an anti-clockwise direction (Fig. 8). Fig. 8 Removing Your Accessory Loosen the locking bolt (16) with the allen key (17) by rotating in a clockwise direction. Remove the locking bolt (16) and the accessory fixing washer (15) from the multi function head. Remove the accessory. Changing Sanding Paper Align the sanding paper (14) to the hook & loop sanding pad (11) and press firmly to hold in place. As this product does not include a dust extraction system, it is not critical that the holes in the sanding paper line up with the holes on the hook & loop sanding pad (11). To remove or change the sanding paper (14) carefully peel it off from one of the triangle ends. Choosing the Correct Sanding Paper Sanding paper is rated according to a number marked on the back. The higher the number, the smaller and finer the grit is on the sanding paper. The lower the number, the larger and more coarse the grit is on the sanding paper. A coarse grit will provide a more aggressive sanding action for quick material removal. Coarse grit (eg.40) is used for removing paint and sanding down rough surfaces. Medium grit (eg.80) is used for sanding down plain timber. Fine grit (eg.120) is used to give a smooth finish to bare wood. Extra fine grit (eg ) is used for polishing or sanding between coats of paint. Note: When using the Multi Function Tool in sanding application, try not to apply excessive pressure when using course grit paper as this can lead to swirl marks on the workpiece. 15

16 MULTI HEAD TOOL OPERATION Variable Speed Trigger Turn on the multi head tool by depressing the variable speed trigger (5) (Fig. 9). To turn off release the variable speed trigger (5). Note: The speed of the multi head tool can be controlled by changing the pressure applied to the variable speed trigger (5). Changing the Direction of Rotation The direction of rotation can be changed with the forward/ reverse selector (4), located above the variable speed trigger (5). To select the forward position, push the forward/reverse selector (4) hard right. To select the reverse drilling position, push the forward/reverse lever (4) hard left (Fig. 10). Forward Fig. 9 Reverse Fig. 10 Note: The variable speed trigger (5) can be locked off by pushing the forward/reverse selector (4) into the middle of both the forward and reverse positions. Caution: Do not change the direction of rotation while the Multi Head Tool is in operation. Wrench Ratchet Head The wrench ratchet head has been designed for light duty fastening applications. WARNING! Do not attempt to use the multi head tool as a manual wrench. Maximum torque for this attachment is 14Nm. Exceeding this rating may cause damage to the multi head tool. WARNING! Do not attempt to attach sockets larger than 12mm to the wrench ratchet head. Maximum torque for this attachment is 14Nm. Exceeding this rating may cause damage to the multi head tool. Note: The wrench ratchet head has a ratchet forward/reverse selector (25) which overrides the forward/reverse selector (4) located on the body of the multi head tool. The direction of rotation should be set using the ratchet forward/reverse selector (25) only. 16

17 MULTI HEAD TOOL OPERATION Set the desired direction of rotation by rotating the ratchet forward/reverse selector (25) (Fig. 11). Turn on the tool by depressing the variable speed trigger (5). Fig. 11 Multi Cutter Head The multi cutter head has been designed for cutting carpets, plastics or cardboard. WARNING! Keep hands, hair and loose items of clothing clear of the multi cutter head. Failure to do so may cause serious personal injury. Ensure the forward/reverse lever (4) is set to the forward position. Turn on the tool by depressing the variable speed trigger (5) and wait until the motor reaches the desired speed. Move the multi cutter head through the material, running between the blade guard (29) and the cutter guide (28). Caution: Avoid forcing the multi cutter head through the workpiece. Allow the tool to do the work. 17

18 MULTI HEAD TOOL OPERATION Multi Function Head Sanding Note: Refer to the Preparation and Setup section of this manual for selecting the correct sandpaper. Always test on a scrap workpiece before using on your workpiece. Avoid applying excessive force to the tool. Allow the sander to do the work. If sanding corners in hard to reach areas use the tip or triangle edge of the sanding pad. Ensure the hook & loop sanding pad (11) is clear of the workpiece. Turn on the tool by depressing the variable speed trigger (5) and wait until the motor reaches the desired speed. Place the hook & loop sanding pad (11) on your workpiece, ensuring the whole area of the sanding paper (14) is in contact with the workpiece. Note: For best results, the hook & loop sanding pad (11) must be kept flat on the workpiece. Do not tilt the tool and use the edge of the sanding paper (14) or the hook & loop sanding pad (11) may become damaged, causing the sanding paper (14) not to adhere to it correctly. Sawing Caution: Clamp your workpiece securely before commencing your work. Note: Ensure your straight saw blade (12) is not blunt or damaged before use. Ensure the straight saw blade (12) is clear of the workpiece. Turn on the tool by depressing the variable speed trigger (5) and wait until the motor reaches the desired speed. If plunging, use a slight pendulum motion to allow sufficient debris removal. Note: Only use the multi function head for plunge cuts on soft materials such as wood or gypsum plaster boards. Ensure there are no nails or screws in the workpiece before cutting. 18

19 MULTI HEAD TOOL OPERATION Scraping Note: The scraper blade (13) is designed for scraping surfaces and the removal of soft materials (eg. paint, glue). Ensure you only apply light pressure to avoid cutting the surface. Ensure the scraper blade (13) is clear of the workpiece. Turn on the tool by depressing the variable speed trigger and wait until the motor reaches the desired speed. Place the scraper blade (13) on the workpiece, using a slight angle. Note: Allow the tool to do the work and do not apply heavy pressure on the scraper blade (13). Heavy pressure can cut into the surface or overload the multi head tool. Right Angle Drill Head Installing Drill or Driver Bits WARNING! Remove battery from the multi head tool before attempting to change accessories. Failure to do so may cause serious personal injury. WARNING! Do not use the power of the drill to tighten or loosen the chuck jaws. The chuck body could slip and your hand could come in contact with a rotating accessory. This could cause an accident resulting in personal injury. Remove the battery (2) from the multi head tool. Open the keyless chuck (18) to a point where the opening is slightly larger than the drill or driver bit you intend to use. Insert the drill or driver bit into the keyless chuck (18). Ensure the end of the drill or driver bit does not touch the screw inside the keyless chuck (18)(Fig. 12). Close the keyless chuck (18) onto the drill or driver bit. Fig. 12 Caution: The right angle drill head is designed for light duty drilling and screwdriving. To prevent damage to the tool, avoid driving large screws or drilling into hard materials with large drill bits. 19

20 MULTI HEAD TOOL OPERATION Removing Drill/Driver Bits Remove the battery (2) from the multi head tool. Loosen the keyless chuck (18). 3. Remove the drill or driver bit. Caution: Do not handle drill bits without gloves as drill bits and other accessories are sharp or can be hot after use. This can cause personal injury. General Hints for Drilling in all Materials Always use sharp drill bits. Mark the place where you would like the hole to be drilled. 3. Commence with a slow speed to start the hole. Refer to the section entitled Variable Speed Trigger for directions on how to control the speed of the right angle drill head. 4. Reduce your pressure on the multi head tool when the drill bit is about to break through the material. Metal Drilling Support thin material with a piece of scrap wood. Use a centre punch to mark the position of the hole. 3. If drilling a large hole, use a small drill bit first to establish a pilot hole. Then use the larger sized drill bit as required. 4. Use only HSS (high speed steel) drill bits or those recommended for metal use. 5. When drilling into iron or steel, use a cooling lubricant such as thin oil. With aluminium, use turpentine or paraffin. With brass, copper and cast iron, use no lubricant but withdraw the drill regularly to assist cooling. Wood Drilling Mark the place where you want to drill with a punch or a nail. To avoid splintering on breakthrough, either clamp a piece of scrap wood to the back of your workpiece or continue the hole from the back of the wood when the drill bit first breaks through. LED Lights The multi head tool has 1 LED Light (6) built into the unit which will illuminate dark areas or tight corners. The LED light is located above the variable speed trigger (5). The LED light (6) turns on automatically when you depress the variable speed trigger (5). 20

21 MAINTENANCE When not in use, the multi head tool should be stored in a dry, frost free location, keep out of children s reach. Keep ventilation slots of the multi head tool clean at all times and prevent any debris from entering. If the housing of the multi head tool requires cleaning use a moist cloth only. Do not use solvents. Blow out the ventilation slots with compressed air periodically. Note: Ozito Industries will not be responsible for any damage or injuries caused by repair of the multi head tool by an unauthorised person or by mishandling. SPARE PARTS Limited spare parts can be ordered subject to availability. Please contact your local Bunnings Special Orders Desk to order the required spare parts. Most common spare parts listed below Spare Part Main Body Drill Head Multi Function Head Wrench Ratchet Head Multi Cutter Head part No. SPMTC SPMTC SPMTC SPMTC SPMTC CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice. Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice. 21

22 DESCRIPTION OF SYMBOLS PACK CONTENTS 1 x Multi Head Tool 1 x Multi Function Head 1 x Right Angle Drill Head 1 x Wrench Ratchet Head 1 x Multi Cutter Head 1 x Sanding Pad 3 x Sanding Sheets 1 x Scraper Blade 1 x Straight Saw Blade 1 x Screwdriver Bit 1 x S2 Square Bit 3 x Drill Bits 2 x Sockets 1 x Hex Key 2 x 12V Battery Packs 1 x Charging Adaptor 1 x Charging Cradle 1 x Kit Bag 1 x Instruction Manual 22

23 WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: 3 YEAR REPLACEMENT WARRANTY Your product is guaranteed for a period of 36 months from the original date of purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in accordance with the terms of this warranty. Warranty excludes consumable parts, for example: included accessories. Lithium Ion batteries are covered by a 12 month warranty. WARNING `Australia New Zealand TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE. The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law. Our goods come with guarantees that cannot be excluded at law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Generally you will be responsible for all costs associated with a claim under this warranty, however, where you have suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by contacting our customer service helpline above. The following actions will result in the warranty being void. Professional, Industrial or high frequency use. If the tool has been operated on a supply voltage other than that specified on the tool. If the tool shows signs of damage or defects caused by or resulting from abuse, accidents or alterations. Failure to perform maintenance as set out within the instruction manual. If the tool is disassembled or tampered with in any way. OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175 OW7