Weighing Scale IDS-802. User Manual

Transcription

1 Weighing Scale IDS-802 User Manual

2 A. MAIN SPECIFICATION Model: Capacity: Accuracy: Display: IDS-802 Weighing scale 3kgx0.1g,6kgx0.2g,15kgx0.5g,30kgx1g Grade III, n=30,000 Single 6 digits LCD with Blue Backlit 1 x LCD Display is optional Keys: Power supply: Operating temperature/humidity: UNIT,COU/AFF,TAR/CAL AC 220V/50Hz or DC 6V/4Ah 5 C~35 C / 85%RH B. OPERATION 1.PREPARATION Put weighing scale on a flat and stable table, adjust the screw of rubber feet if the table is not flat. Avoid shaking, sunshine and strong EMI (Electromagnetic Interference). 2.POWER ON AND AUTO ZERO SETTING 2.1 Connect power cord to 220V power supply 2.2 Push button [ON/OFF] to turn on the scale, the display window will perform "999999"" ","777777",'666666","555555""444444", "333333", "222222", "111111","000000",and to self checking, then it will enter into weighing mode by displaying "0" or "0.0 ". 2.3 When power on, if loading weight on the scale deviates from the zero

3 point, but still within zero set range, the scale will set zero automatically; if out of range, it is necessary to adjust the zero point or recalibrate or reset. 3.MANUAL ZERO SETTING (automatically) 3.1 In weighing mode, when there is some error when unloaded, press [TAR/CAL] to make the scale to be zero. 3.2 If the displayed value deviates from zero point, but still within zero range, pressing [TAR/CAL]key is available. Otherwise, [TAR/CAL] key is invalid.(in this situation, please recalibrate or reset zero parameters) 3.3 Only when stable sign (on the left corner of display window) shows, zero operation is available. 4.TARE When scale is in weighing status, and displaying positive weight stable, press [TAR/CAL]key, scale will deduct the displayed weight value as tare weight. Then it displays net weight as "0.0". 5.UNIT OPTIONAL When at weighing mode, press [UNIT] to change units between g, kg, oz, lb, t 6.WEIGHING 6.1 Turn on the scale, it displays weighing mode "0.0" 6.2 Put goods on the platter, it will display weight.

4 7.COUNT 7.1 Average Piece Weight Setting Put a container for parts on the platter or not (if not necessary), press [COU/AFF], the scale will display "10" (flashing), then put 10 pcs parts on the container or platter, press [COU/AFF]to confirm, the scale will enter into waiting mode by displaying "------" for a while, then it will display "10" to finish average piece weight setting. Average pieces are available: press [TAR/CAL]to choose average piece from "10,20,50,100,200,500", other process is the same as above. 7.2 COUNT OPERATION Put parts to be counted on the platter, press [COU/AFF], the scale will display piece number Press [COU/AFF] again to exit from counting mode. 8.OVERLOAD ALARM If the loading weight is larger than (1+0.2%) of full capacity, the scale will display " ", meaning overload. Take off the goods immediately to avoid damaging the scale. 8. Power-saving When the weighing mode is stable, the scale will automatically turn off the backlight to enter into auto power-saving status. When the weighing is unstable, the backlight will turn on automatically.

5 C. CALIBRATION Before using the scale, please check the accuracy of the scale. If not accurate, please calibrate the scale with standard calibration weights. 1 Turn on the scale for preheating 10 minutes. 2 Make sure the scale is unloaded and in zero mode, long press [TAR/CAL] to initiate calibration (do not release key-press until "--CAL-- " is displayed). Then the required calibration weight is displayed (ex g means 3kg weight).put the corresponding calibration weights on the pan, the scale will display " " for a while, and then display the value of weight. Then remove the calibration weight, the scale will display " " and then display "0.0" to end calibration. D. ERROR INDICATION Error information Explanation Solution Underline The weight is negative Recalibrate Hyphen Overload Recalibrate Not accurate weighing and cannot calibrate Load cell damaged Change load cell Line and display Battery finishes Recharge battery

6 E. CHAREABLE BATTERY 1.Turning on the AC Power, the scale will charge the battery automatically. 2. Only when you turn off the AC power and push [ON/OFF] key, battery works. 3.When you use battery first time, you should charge the battery for 20 hours in order to prevent low voltage resulted from the self leakage of the battery. 4. If you don't use battery for a long time, you should charge the battery for hours for each two month to prolong using life of battery. 5.The battery is easily exhausted products. And it is not granted free guarantee. F. ATTENTION 1.Preheat the scale before use 2. The total weight of tare weight and goods should not over max capacity. 3.Calibrate the scale if the weighing is not accurate. G. MAINTENANCE 1. To guarantee the scale display clarity and using life, do not place it directly under sunshine or where dust pollution and vibration are serious. 2. It is strictly forbidden to clean the scale with intensive solvents 3. Liquid and conducting parts should not be poured into the scale,

7 otherwise electronic components will be damaged and electric shock is likely to happen. 4. During operation, if trouble occurs, operator must pull off the power supply plug immediately. 5. From invoice date, the scale has one-year free repair period. If any non-artificially obstacle about the scale happens under correct using conditions within this period, the user is allowed to send the product with its guarantee card back to our factory for free repair. The scale should not be taken apart, otherwise free guarantee will be cancelled. 6. The battery and load cell (overload is strongly forbidden) are not within the scope of warranty. 1. Function keys: UNIT, COU/AFF, TAR/CAL 2. Stainless steel platter 3. Push button keys for On, Off 4. Overload and underload protection 5. Auto shut-off to save energy & increase battery life 6. Low-Battery Indication / Over-Load Indication 7. Battery life: 120HRS with backlit off after once charging 8. Non-slip feet for stability 9. ONE YEAR FACTORY WARRANTY