PSR 960 PSR 1200 PSR 1440
|
|
- Johnathan Phelps
- 5 years ago
- Views:
Transcription
1 Buch Seite 1 Montag, 18. November :07 08 Operating Instructions PSR 960 PSR 1200 PSR 1440 English
2 Buch Seite 2 Montag, 18. November : PSR 960 PSR 1200 PSR A B
3 Buch Seite 1 Montag, 18. November :07 08 Tool Specifications Battery-Powered Screwdriver PSR 960 PSR 1200 PSR 1440 Part number Idling speed [rpm] Torque, max. [Nm] max. drilling Ø Steel [mm] Soft wood [mm] Hard wood [mm] Screw diameter, max. [mm] Drill spindle threads 3/8" 3/8" 3/8" Weight with battery, approx. [kg] Battery NiCd NiCd NiCd Temperature monitor NTC NTC NTC Rated voltage [V=] Weight [kg] Please observe the order number of your machine. The trade names of the individual machines may vary. Operating Controls 1 Torque setting ring 2 Keyless chuck 3 Rotational direction switch 4 On/Off switch 5 Battery 6 Battery unlocking button 7 Screwdriver attachment (bit) 8 Universal bit holder Not all the illustrated or described accessories are included as standard delivery. Intended Use The machine is intended for the screwing in and loosening of screws and for drilling in wood, metal, ceramics and plastic. Noise/Vibration Information Measured values determined according to EN The A-weighted sound pressure level of the tool is less than 70 db (A). The noise level when working can exceed 85 db (A). Wear ear protection! The typical hand-arm vibration is below 2.5 m/s 2. For Your Safety Working safely with this machine is possible only when the operating and safety information is read completely and the instructions contained therein are strictly followed. In addition, the general safety notes in the safety notes section must be observed. Wear safety glasses. If you have long hair, wear a protective hairnet. Work only with close-fitting clothes. Before each use, check the machine and battery. If damage is detected, do not use the machine. Have repairs performed only by a qualified technician. Never open the machine yourself. Before any work on the machine itself (e. g. maintenance, tool change, etc.) as well as when transporting and storing it, always set the rotational direction switch to the middle position. Otherwise an injury may occur when unintentionally pressing the On/Off switch. Before using, make sure the battery fits securely inside the machine. Do not load the machine so heavily that it comes to a standstill. Always hold the machine securely because strong reaction moments can occur as a result of the driving-in process TMS English - 1
4 Buch Seite 2 Montag, 18. November :07 08 Secure the workpiece. Clamping devices or a vise will hold the workpiece in place better than the hand. Never allow children to use the machine. Bosch can only guarantee a flawless functioning of the machine if the original accessories intended for it are used. Battery and Battery Charger The enclosed operating instructions for the battery charger must be read carefully! Allow heated batteries to cool before charging. Protect the battery from heat and fire: Explosion risk! Do not place the battery on radiators or expose it to strong sun rays for a long time period; temperatures over 50 C cause damage. Do not open the battery and protect from impact. Store in a dry and frost-free place. Do not dump the battery into the household waste, fire or water. Before Use Battery Charging A battery that is new or has not been used for a longer period does not develop its full capacity until after approximately 5 charging/discharging cycles. To remove the battery 5, press the unlocking buttons 6 and pull out the battery downwards. Do not exert any force. The battery is equipped with an NTC temperature monitor which allows charging only within a temperature range of 0 C to 45 C. This will prolong the useful life of the battery. A significantly reduced working period after charging indicates a used up battery that must be replaced. Observe the indications regarding environmental protection. Changing the Tool Open the chuck until the tool can be inserted. Then, insert the tool. Hold the rear sleeve tight and firmly tighten the front sleeve by hand, until the locking action ( click ) is no longer heard. The drill chuck is locked automatically. The locking is released again when the front collar is turned in the opposite direction to remove the tool. Screwdriving (see figures A + B ) Clamp the bit 7 directly into the drill chuck. We recommend using the universal bit holder 8 for quick changes. Initial Operation Inserting the Battery Set the rotational direction switch 3 to the center position = lock-off and allow the charged battery 5 to engage into the handle. Switching On and Off To start the unit, press the On/Off switch 4. The machine runs with variable speed between 0 and maximum depending on the pressure applied to the On/Off switch 4. Light pressure results in a low rotational speed, thus allowing smooth, controlled starts. Do not load the machine so heavily that it comes to a standstill. To switch off the unit, release the On/Off switch 4. Run-On Brake When the On/Off switch 4 is released, the chuck brakes to a stop, thus preventing the run-on of the tool. For screwdriving work, wait until the screw is screwed in flush with the material and then release the On/Off switch 4. By doing so, the head of the screw does not penetrate into the material TMS English - 2
5 Buch Seite 3 Montag, 18. November :07 08 Changing the Rotational Direction Operate the rotational direction switch 3 only at a standstill. The rotational direction switch 3 changes the directional rotation of the machine. However, this is not possible if the On/Off a b switch 4 is being pressed. Right Rotation ( a ) Turn the rotational direction switch through to the left stop (normal operation: drilling, driving in screws, etc). Left Rotation ( b ) Press the rotational direction switch to the right as far as it will go (loosening or unscrewing of screws and nuts). Setting the Torque Carry out a practical test to determine with which one of the 5 settings of the torque setting ring 1 the screws are driven flush into the material. Low setting, e. g., small screws, soft 1 materials. High setting, e. g., large screws, hard 5 materials. With the correct setting, the clutch disengages as soon as the screw is driven flush into the material or the set torque is reached. Select a higher setting when driving out screws, or set to the Drilling symbol. The correct setting is to be determined by practical testing. Drilling Set the torque setting ring 1 to the Drilling symbol. Replacing the Chuck For machines without a drill spindle locking facility, the chuck must be changed by an authorized customer service facility for Bosch power tools. The chuck must be tightened with a starting torque of approx Nm. Tips It is advisable to drill a pilot hole first before attempting to screw in large, long screws into hard materials. Maintenance and Cleaning Before any work on the machine itself, remove the battery. For safe and proper working, always keep the machine and the ventilation slots clean. Should the machine fail in spite of careful manufacturing and testing, its repair should be carried out by a Bosch power tools authorized service agent. For all correspondence and spare parts orders, always include the 10-digit part number of the machine! Environmental Protection Recycle raw materials instead of disposing them as waste The machine, its accessories and packaging materials should be sorted for environmentallyfriendly recycling. These instructions are printed on chlorine-free recycled paper. The plastic components are labeled for categorized recycling. Nickel-cadmium-battery: If your product is equipped with a nickel-cadmium-battery, the battery must be collected, recycled or disposed of in an environmentally-friendly way. Defective or worn-out batteries must be recycled according to the 91/157/EEC guideline TMS English - 3
6 Buch Seite 4 Montag, 18. November :07 08 Service In case of a claim, repair or purchase of replacement parts or in case of queries or other problems please contact your local dealer or Bosch representative. People s Republic of China Shanghai C. Melchers Ltd. 13/Fl, East Ocean Centre 588 Yan an Road (East) Shanghai (0)21 / Fax (0)21 / Guangzhou C. Melchers Ltd. Room 1108, T.P. Plaza 9/109 Liu Hua Road Guangzhou (0)20 / Fax (0)21 / Beijing C. Melchers Ltd. Beijing Representatives Room Beijing Tower No. 10 Chang an Avenue (East) Beijing (0)10 / Fax (0)10 / Hongkong C. Melchers Ltd Shun Tak Centre, West-Tower 200 Connaught Road, Central Hongkong / Fax / Subject to change General Safety Rules WARNING! Read all instructions. Failure to follow the instructions listed below may result in electric shock, fire and/or serious injury. The term power tool as used in all of the warnings listed below refers to your mains operated (corded) power tool and to battery operated (cordless) power tool. SAVE THESE INSTRUCTIONS. 1) Work area a) Keep the work area clean and well lit. Cluttered and dark areas can lead to accidents. b) Do not operate power tools in explosion-risk areas where there are flammable liquids, gases or dust. Power tools create sparks, which may ignite dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock. b) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts of tools. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for the appropriate power tool will reduce the risk of personal injuries. c) Avoid accidental starting. Ensure the switch is in the OFF position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can get caught by moving parts. g) If dust extraction and collection devices can be mounted, make sure that they are connected and properly used. Use of these devices can reduce dust-related hazards TMS English - 4
7 Buch Seite 5 Montag, 18. November : ) Proper care and use of power tools a) Do not force the power tool. Use the correct power tool for your job. The correct power tool will do the job better and safer at the rate for which it was designed. b) Never use a power tool whose switch is defective. Any power tool whose switch cannot be turned off and on is dangerous and must be repaired. c) Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the machine. Power tools are dangerous in the hands of inexperienced users. e) Properly maintain power tools. Check for the smooth and perfect functioning of moving parts, breakage of parts and any other damaging condition that may affect their operation. If damaged, have the power tool repaired before use. Poorly maintained power tools cause many accidents. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and therefore easier to control. g) Use the power tool, its accessories and tool bits etc., in accordance with these instructions and in the manner intended for that particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Battery tool use and care a) Ensure the switch is in the OFF position before inserting the battery pack. Inserting the battery pack into power tools that have the switch on could lead to accidents. b) Recharge only with a charger recommended by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. c) Use power tools only with those battery packs specifically designated for them. Use of any other battery packs may create a risk of injury and fire. d) When not using the battery pack, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. e) Improper use may cause liquid to be ejected from the battery; avoid contact with it. If contact accidentally occurs, flush with water. If liquid reaches the eyes, seek medical help as well. Liquid ejected from the battery may cause skin irritation or burns. 6) Service a) Have your power tool serviced by a qualified technician who uses only original replacement parts. This will ensure that the safety of the power tool is maintained TMS English - 5
8 Buch Seite 1 Montag, 18. November :07 08 PSR 960 PSR 1200 PSR [ ] [ ] [ ] [ ] [ ] [ ] /8 3/8 3/8 [ ] 1,3 1,4 1,5 NiCd NiCd NiCd NTC NTC NTC [ =] 9, ,4 [ ] 0,4 0,5 0, (Bit) 8 EN db (A) 85 db (A) 2,5 m/s 2 Bosch TMS
9 Buch Seite 2 Montag, 18. November : NTC A B a b a b TMS
10 Buch Seite 3 Montag, 18. November : Bosch Bosch 10 Nickel-Cadmium- Nickel-Cadmium- 91/ / / boschinfo@melchers.com.tw TMS
11 Buch Seite 4 Montag, 18. November : ) a) b) c) 2) a) b) c) d) e) 3) a) b) c) d) e) f) g) 4) a) b) c) d) e) f) g) 5) a) b) c) d) e) 6) a) TMS
12 Buch Seite 2 Montag, 18. November : AL 300 SV * 0,8 x 5,5 mm * PH Nr * PZ Nr * T * SW 3 mm *
13 Buch Seite 1 Montag, 18. November :07 08 Chlor Robert Bosch GmbH Geschäftsbereich Elektrowerkzeuge Leinfelden-Echterdingen (02.11) O / 16 Printed in Malaysia - Imprimé en Malaisie
RMT1201. ORIGINAL INSTRUCTIONS Cordless Multi-Tool
RMT1201 ORIGINAL INSTRUCTIONS Cordless Multi-Tool Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. Safety GENERAL
More informationoriginal instructions 18V Torch RFP1801
original instructions 18V Torch RFP1801 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. Safety GENERAL POWER
More information4V LITHIUM-ION SCREWDRIVER OWNER S OPERATING MANUAL
CSD-4107BG 4V LITHIUM-ION SCREWDRIVER OWNER S OPERATING MANUAL Your screwdriver has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When
More informationSAFETY AND OPERATING MANUAL. Lithium-Ion cordless hammer drill WX372 WX372.1 WX372.9
SAFETY AND OPERATING MANUAL 2 Original Instructions General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
More information18V CORDLESS DRILL DRIVER CDT16180
18V CORDLESS DRILL DRIVER CDT16180 LX400 SAFETY INSTRUCTIONS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or
More informationInstruction Manual. CORDLESS DRILL 18V Li-ion WITH IMPACT FUNCTION. Model SROM 1172
Instruction Manual CORDLESS DRILL 18V Li-ion WITH IMPACT FUNCTION Model SROM 1172 Our tool range has you covered for DIY. Whatever the job, make light work of it with MAKO tools. Product Features: 1. Keyless
More informationRPS1215 ORIGINAL INSTRUCTIONS. Cordless Pruner
RPS5 ORIGINAL INSTRUCTIONS Cordless Pruner Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.
More informationeclipse Instruction Manual 4.0V Li-Ion Screwdriver Part #:
eclipse Instruction Manual 4.0V Li-Ion Screwdriver Part #: 902-588 Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com Test Equipment Depot - 800.517.8431-99
More informationTOOLPRO 18V 2 Speed Drill Driver
TOOLPRO 18V 2 Speed Drill Driver Instruction Manual CDT218G.1 After Sales Support FREE CALL 1300 889 028 EMAIL:salesau@positecgroup.com Important - Please read these instructions fully before operating
More informationCordless Driver Drill
INSTRUCTION MANUAL Cordless Driver Drill MT064 MT065 003947 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model MT064 MT065 Steel 0 mm 3 mm Capacities Wood 25 mm 28 mm Wood
More informationOPERATOR'S MANUAL. Cat. No. C12 PC. To reduce the risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL Cat. No. C12 PC M12 Cordless Copper Tubing Cutter To reduce the risk of injury, user must read and understand operator's manual. General POWER TOOL SAFETY WARNINGS WARNING Read all safety
More informationInstruction Manual CORDLESS DRILL & DRIVER 18V. Model SROM 1170
Instruction Manual CORDLESS DRILL & DRIVER 18V Model SROM 1170 Product Features: Dear Valued Customer, Thank you for purchasing this Samson Power Tool. We are dedicated to providing quality Samson Power
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 7 6 2 5 4 2 3 A1 A2 1 2 A3 B A3 B C1 C2 3 C3 D 1. FORWARD/ REVERSE ROTATION CONTROL 2. SOFT GRIP HANDLE 3. BATTERY PACK RELEASE BUTTON 4. BATTERY PACK*
More informationSAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 2 3 4 9 8 5 6 7 A1 A2 1 2 1 3 2 A3 B1 3 2 1 B2 C1 2 3 1 C2 C3 C2 C3 D F E 1. KEYLESS CHUCK 2. TORQUE ADJUSTMENT RING 3. TWO-SPEED GEAR CONTROL 4. FORWARD/REVERSE
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill 607D 637D 6337D 6347D 0089 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 607D 637D 6337D 6347D
More informationSSW 18 LTX 600 SSW 18 LTX 400 BL
SSW 18 LTX 600 SSW 18 LTX 400 BL en Operating Instructions 5 fr Mode d'emploi 9 es Instrucciones de manejo 13 www.metabo.com SSW 18 LTX 400 BL 1 SSW 18 LTX 600 1 2 3 2 3 4 5 7 4 7 6 6 9 8 9 8 10 2 11.
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill 670D 680D 6390D R 0056 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 670D 680D 6390D Steel
More informationCordless Driver Drill
INSTRUCTION MANUAL Cordless Driver Drill FD0 008796 ENGLISH (Original instructions) SPECIFICATIONS Model FD0 Steel 0 mm (3/8") Capacities Wood 2 mm (3/6") Wood screw 5. mm x 63 mm (7/32" X 2-/2") Machine
More informationR18DDBL ORIGINAL INSTRUCTIONS. 18V Brushless Drill Driver
R18DDBL ORIGINAL INSTRUCTIONS 18V Brushless Drill Driver Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 2 3 4 8 9 5 7 6 A1 A2 1 2 1 3 2 A3 B1 A3 B1 3 2 1 B2 C1 2 3 1 C2 C3 D E1 1-18 D E1 E2 E3 F 1-18 6 1. CHUCK 2. TORQUE ADJUSTMENT RING 3. TWO-SPEED GEAR
More informationPT-1441 Cordless Drill Driver 14.4V User s Manual
PT-1441 Cordless Drill Driver 14.4V User s Manual 1 st Edition, 2009 2009 Copy Right by Prokit s Industrial Co., Ltd. Please read this handbook carefully before using the tool General Safety Rules WARNING
More informationTOOLPRO 18V Li-Ion Brushless Impact wrench
TOOLPRO 18V Li-Ion Brushless Impact wrench Instruction Manual CIW180HB.9 After Sales Support FREE CALL 1300 889 028 EMAIL:salesau@positecgroup.com Important - Please read these instructions fully before
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 2 3 4 9 5 8 7 6 A2 A1 1 2 B1 A3 3 2 1 C1 B2 2 3 1 C2 C3 C2 C3 D E F G -- -- -- = 1. CHUCK 2. TORQUE ADJUSTMENT RING 3. TWO-SPEED GEAR CONTROL 4. FORWARD/REVERSE
More information1200W CaR PoliSheR en RS4900
1200W Car Polisher RS4900 RS4900 8 1 2 7 3 4 5 6 A B flat nozzle C D E F 1200W Car Polisher RS4900 G H flat nozzle I J K L 4 1200W Car Polisher COMPONT LIST 1 2 3 4 5 6 7 Variable speed control Switch
More informationINSTRUCTION MANUAL. Cordless Angle Drill XAD01
INSTRUCTION MANUAL Cordless Angle Drill XAD0 0474 ENGLISH (Original instructions) SPECIFICATIONS Model XAD0 Capacities Steel 0 mm (3/8") Wood 25 mm (") No load speed (RPM) 0 -,800 /min Overall length 34
More informationSFC 18 A SFC 22 A English
SFC 18 A SFC 22 A English en 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a is a prerequisite for safe, trouble-free
More information18V CORDLESS DRILL MODEL NO: CON18LiC
18V CORDLESS DRILL MODEL NO: CON18LiC PART NO: 6479531 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0817 - ISS 2 INTRODUCTION Thank you for purchasing this CLARKE Cordless Drill. Before
More informationInstruction Manual 4.0V Li-Ion Screwdriver. Part #: ECLIPSE ENTERPRISES, INC Chula Road, Amelia Court House, VA 23002, U.S.
Instruction Manual 4.0V Li-Ion Screwdriver Part #: 902-588 ECLIPSE ENTERPRISES, INC. 13302 Chula Road, Amelia Court House, VA 23002, U.S.A 2 3 Intended use Your ECLIPSE ENTERPRISES, INC. 902-588 screwdriver
More information18V CORDLESS COMBI DRILL MODEL NO: CON18NI
CON18NI.fm Page 1 Tuesday, August 21, 2012 11:53 AM 18V CORDLESS COMBI DRILL MODEL NO: CON18NI PART NO: 6485067 OPERATION & MAINTENANCE INSTRUCTIONS LS0812 CON18NI.fm Page 2 Tuesday, August 21, 2012 11:53
More informationSAFETY AND OPERATING MANUAL. Cordless Hedge Trimmer WG259E WG259E.5 WG259E.9
SAFETY AND OPERATING MANUAL 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire
More information24V CORDLESS HAMMER DRILL
24V CORDLESS HAMMER DRILL CDI224MN ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
More informationELECTRIC ENGRAVER 15W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS WHAT S IN THE BOX. ozito.com.au. Electric Engraver
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
More informationSAFETY AND OPERATING MANUAL. Cordless rotary hammer WX382 WX382.1 WX382.2 WX382.3 WX382.4
SAFETY AND OPERATING MANUAL Original instructions 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
More informationC O R D L E S S I M PA C T D R I V E R W I T H 1 2 V LI- I O N B AT T E RY OWNER S MANUAL
C O R D L E S S I M PA C T D R I V E R W I T H 1 2 V LI- I O N B AT T E RY OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow
More informationSBC12 H Operating instructions Mode d emploi Manual de instrucciones
*254901* 254901 SBC12 H Operating instructions Mode d emploi Manual de instrucciones Safety Precautions Read all Instructions GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS WARNING! Read and understand
More informationW6VB3 W8VB2. Handling instructions
Screw Driver Model W 6VM W 6V4 W 6VA4 W 6VB3 W 8VB2 Handling instructions W6VM W6V4 W6VA4 W6VB3 W8VB2 Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to
More information4-VOLT LITHIUM-ION AUTO-LOAD SCREWDRIVER w/led WORKLIGHT
SKU 241-1394 4-VOLT LITHIUM-ION AUTO-LOAD SCREWDRIVER w/led WORKLIGHT Operation Manual WARNING! Please read this manual before using this product. Failure to do so can result in serious injury. SAVE THIS
More informationRD V RECIPRO/PRUNING SAW
RD2865 RD2865 7 1 6 2 3 5 4 8 9 RD2865 1 A B C 2 7 1 2 D E F1 F2 COMPONT LIST 1 2 3 4 5 6 7 8 9 TOOL-FREE BLADE CLAMP LEVER LOCK-OFF BUTTON HANDLE BATTERY PACK * BATTERY PACK RELEASE LATCH ON/OFF SWITCH
More informationWHAT S IN THE BOX METAL CUTTING SHEARS. Metal Cutting Shears 500W INSTRUCTION MANUAL SPECIFICATIONS. Hex Key. Max. Thickness: ozito.com.
WHAT S IN THE BOX METAL CUTTING SHEARS 500W INSTRUCTION MANUAL SPECIFICATIONS Motor: No load speed: Max. Thickness: Tool weight: 500W 0 1,600 rpm 1.2mm 2.2kg Metal Cutting Shears Hex Key ozito.com.au MCS-5000
More informationSFC 14 A SFC 22 A English
SFC 14 A SFC 22 A English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling
More informationCordless Impact Wrench
ENGLISH INSTRUCTION MANUAL Cordless Impact Wrench BTW0 00534 WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH SPECIFICATIONS Capacities
More informationWR 22SE WR 25SE WR25SE. Handling instructions
WR 22SE WR 25SE WR25SE Handling instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric
More informationCordless Driver Drill
INSTRUCTION MANUAL Cordless Driver Drill XFD0 0360 ENGLISH (Original instructions) SPECIFICATIONS Model XFD0 Steel 3 mm (/") Capacities Wood 38 mm (-/") Wood screw 0 mm x 89 mm (3/8" X 3-/") Machine screw
More informationSAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS LITHIUM-ION BRUSHLESS DRILL DRIVER LITHIUM-ION BRUSHLESS HAMMER DRILL WU175 WU175.1 WU309 1 2 3 4 10 5 9 8 6 7 12 11 100% A1 A2 0% 1 2 A3 A4 B1 B2 2 C1
More information기술데이터. 밧데리형태 NiCd 전압 VDC 18 용량 Ah 2.4 중량 kg 1. 충전기 D9116 본선전압 VAC 230 밧데리형태 NiCd/NiMH 평균충전시간 분 60/70 중량 kg 0.4 기술및제품개발담당이사홀스트그로스만다음은본설명서에사용되고있는기호입니다 :
DEWALT DC212 DC213 충전로타리해머드릴 DC212/DC213* EC- 적합성선언 C E DC212/DC213 상기 DEWALT 사의전동공구제품들은 98/37/EEC, 89/336/EEC, 73/23/EEC, 86/188/EEC, EN60745, EN55014-2, EN55014, EN50260, EN60335, EN61000-3-2 와 EN61000-3
More informationCordless Rechargeable Saw Instructions for Use
Technical data Voltage: DC 10.8V Weight: 1.25Kg Stroke rate: 0-2100/min Stroke: 15mm Cutting capacity: max diameter in wood 80mm / in soft metal 7mm Charging time: Between 5.0-5.5 Hours Battery: 1.3Ah
More informationHDE 500-A22. English. Printed: Doc-Nr: PUB / / 000 / 03
HDE 500-A22 English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and
More information12V CORDLESS DRILL DRIVER. Model HY2150. User Manual
12V CORDLESS DRILL DRIVER Model HY2150 User Manual CONTENTS Section Description Page N o /N o s 1. OWNER S MANUAL & SAFETY INSTRUCTIONS 3 2. GENERAL SAFETY 3 5 3. BATTERY PACK 5 6 4. CHARGING 6 5. INSERTING/REMOVING
More informationCordless Line Trimmer
RLT6X RLT6B ORIGINAL INSTRUCTIONS Cordless Line Trimmer Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating this machine. Subject to technical
More informationCordless Driver Drill
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Driver Drill DF02D Read before use. SPECIFICATIONS Model: DF02D Drilling capacities Steel 5 mm Wood 6 mm Fastening capacities Wood screw ø3.8
More informationATD V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual
ATD 10525 12V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual KNOW YOUR PRODUCT (DRILL) 1. Keyless chuck 2. Torque adjustment collar 3. Speed selector 4. Forward/reverse selector 5. Battery
More informationWR 16SE. de fr it nl es pt sv da no fi el pl hu cs tr ro sl sk bg sr hr uk ru. Handling instructions
en WR 16SE de fr it nl es pt sv da no fi el pl hu cs tr ro sl sk bg sr hr uk ru Handling instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to
More informationELECTRIC CAR POLISHER
ELECTRIC CAR POLISHER MODEL NO: CP254 PART NO: 6462108 OPERATION & MAINTENANCE INSTRUCTIONS LS0610 INTRODUCTION Thank you for purchasing this CLARKE electric car polisher. Before attempting to use this
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill DDF343 DDF453 009075 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DDF343 DDF453 Steel 0 mm
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill 6095D 002032 WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
More informationPower Paint Scraper 200W CPS-200. To view the full range visit: Instruction Manual 3 Year Replacement Warranty
Power Paint Scraper 200W Instruction Manual 3 Year Replacement Warranty CPS-200 WARNING! Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric
More informationCORDLESS TACKER MODEL NO: CCT48 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0414
CORDLESS TACKER MODEL NO: CCT48 PART NO: 6485070 OPERATION & MAINTENANCE INSTRUCTIONS LS0414 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read
More information3.6V SCREWDRIVER INSTRUCTION MANUAL CSD36F
3.6V SCREWDRIVER INSTRUCTION MANUAL CSD36F ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions
More informationCORDLESS DRILL User Manual EN
CORDLESS DRILL User Manual EN B1 7 1 6 9 11 2 3 5 8 4 B2 B3 5 4 4 B4 1 B5 8 6 Lo Hi 9 3 2 2 B6 B7 7 7 b a 7 B8 10 1 Description of the tool 1 Selection Torque 2 Inverter Switch 3 ON/OFF 4 Battery 5 Pushlock
More information24 Volt - 3/8" Cordless Impact Wrench
24 Volt - 3/8" Cordless Impact Wrench INSTRUCTION MANUAL Item # 3994040 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical equipment such as this, basic safety precautions should always be followed
More informationPower Carver 50W CPC-050. To view the full range visit: Instruction Manual 3 Year Replacement Warranty
Power Carver 50W Instruction Manual 3 Year Replacement Warranty CPC-050 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock,
More informationCat. No. M18 Cordless multi-tool. To reduce The risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL Cat. No. M18 Cordless multi-tool To reduce The risk of injury, user must read and understand operator's manual. 2 General POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and
More informationIn-line Cordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL In-line Cordless Driver Drill DF00D 008706 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DF00D Steel 5 mm Capacities
More informationCordless High Speed Drill
ENGLISH Cordless High Speed Drill MODEL 6503D 00039 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
More informationGTC650L-XE Australia New Zealand
www.blackanddecker.com.au GTC650L-XE Australia New Zealand 2 11 D1 D2 D3 D4 3 ENGLISH (Original instructions) Intended use Your Black & Decker hedgetrimmer has been designed for trimming hedges, shrubs
More informationEVO181B1. English
EVO181B1-TW EVO181B1-KR EVO181B1 English 4 10 16 A B 8 C EVO181B1-KR EVO181B1-TW D 2 E 13 8 9 EVO181B1-KR EVO181B1-TW F 3 ENGLISH (Original instructions) EVO181B1 MULTI TOOL Technical data Multi Tool Voltage
More informationCordless Impact Driver JCB-ID20LIBL
Safety and operating manual Cordless Impact Driver JCB-ID20LIBL ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
More information360 LINE LASER LEVEL. 20m Working Range WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au LLT-3605 WHAT S IN THE BOX
WHAT S IN THE BOX 360 LINE LASER LEVEL 20m Working Range INSTRUCTION MANUAL SPECIFICATIONS Battery: Laser Power: Working Range: Laser Diode: Accuracy: 6V DC (4 x AA Battery) Class 2,
More information19.2V CORDLESS 2-IN-I COMBO KIT OWNER'S MANUAL
19.2V CORDLESS 2-IN-I COMBO KIT OWNER'S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More informationBelt Sander JCB-BS950
Safety and operating manual Belt Sander JCB-BS950 ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions
More informationOWNER S TECHNICAL MANUAL
OWNER S TECHNICAL MANUAL 18V Cordless Grease Gun 450g 670AN3 Description These model guns are designed to dispense petroleum-based greases (up to NLGI 2) for general lubrication applications. A 36-inch
More informationCordless Driver Drill DS 9DVC DS 12DVC
Cordless Driver Drill DS 9DVC DS 12DVC HANDLING INSTRUCTIONS DS 12DVC Read through carefully and understand these instructions before use. 1 2 3 6 5 1 3 2 3 4 12 3 7 1 2 0 8 u 4 1 5 6 2 @ # # $!! 5 0 9
More informationENGLISH (Original instructions) INSTRUCTION MANUAL. Cordless Angle Drill DA330D DA331D. IMPORTANT: Read Before Using.
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Angle Drill DA330D DA33D 03258 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DA330D DA33D Capacities Steel
More information18V CORDLESS STAPLER/NAILER
18V CORDLESS STAPLER/NAILER MODEL NO: CONSN18LI PART NO: 6487055 OPERATION & MAINTENANCE INSTRUCTIONS LS1213 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product,
More informationINSTRUCTION MANUAL. MODEL No: FLEXC-3PX FLEXC-8PX FLEXC-11PX FLEXC-12PX 10.8V Cordless Shut-off Screwdriver.
a) Torque adjustment cover b) 1/4" F/Hex with quick change chuck c) LED indicator provides simple process information to the operator d) LED light for working in dark area e) Press button for easy Forward/Reverse
More informationQUICK CONNECT SYSTEM 18V POWER UNIT & DRILL ATTACHMENT Australia BDCDMT180 New Zealand
QUICK CONNECT SYSTEM 18V POWER UNIT & DRILL ATTACHMENT www.blackanddecker.com.au BDCDMT180 Australia New Zealand 5 A B C D E 2 (Original instructions) ENGLISH Intended use Your Black & Decker MATRIX multi-purpose
More informationENGLISH (Original instructions) INSTRUCTION MANUAL. Cordless Nibbler BJN160 BJN161. IMPORTANT: Read Before Using.
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Nibbler BJN60 BJN6 07 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model BJN60 BJN6 Steel up to 400 N/mm.6 mm
More informationOPERATOR'S MANUAL M12 FIR38, M12 FIR12 M12 FUEL RATCHETS WARNING. Cat. No.
OPERATOR'S MANUAL Cat. No. M12 FIR38, M12 FIR12 M12 FUEL RATCHETS WARNING To reduce the risk of injury, user must read and understand operator's manual. GENERAL POWER TOOL SAFETY WARNINGS WARNING Read
More information18V Cordless Precision Clutch Shut Off Pistol Screwdriver SPC-P2625Q SPC-P2925Q SPC-P21225Q
18V Cordless Precision Clutch Shut Off Pistol Screwdriver MODEL NO.: SPC-P2325Q SPC-P2625Q SPC-P2925Q SPC-P21225Q 2 (A) (B) (C) (D) (E) (H) (F) (G) (I) (A) 1/4" Hex with quick change chuck. (B) Covered
More informationCordless Impact Driver
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Impact Driver TD0D Read before use. SPECIFICATIONS Model: TD0D Fastening capacities Machine screw 4 mm - 8 mm Standard bolt High tensile bolt
More informationOPERATOR'S MANUAL M12 FID M12 FUEL 1/4" HEX IMPACT DRIVER WARNING. Cat. No.
OPERATOR'S MANUAL Cat. No. M12 FID M12 FUEL 1/4" HEX IMPACT DRIVER WARNING To reduce the risk of injury, user must read and understand operator's manual. GENERAL POWER TOOL SAFETY WARNINGS WARNING Read
More informationFunctional Description and Specifications. Intended Use. Packing List
Functional Description and Specifications Intended Use The Nemo Submersible Hammer Drill is intended to drill tough materials such as cement, brick, blocks, or stone, and can be used underwater, in wet
More informationPSR 18 LI. Robert Bosch GmbH Power Tools Division Leinfelden-Echterdingen Germany X (2011.
OBJ_DOKU-27603-001.fm Page 1 Monday, August 22, 2011 5:27 PM Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-pt.com PSR 18 LI 1 619 X06 940 (2011.08) O / 10 XXX en
More informationOPERATOR'S MANUAL WARNING. Cat. No. M18 FMTIWP12, M18 FMTIWF12 M18 FUEL MID-TORQUE IMPACT WRENCHES
OPERATOR'S MANUAL Cat. No. M18 FMTIWP12, M18 FMTIWF12 M18 FUEL MID-TORQUE IMPACT WRENCHES WARNING To reduce the risk of injury, user must read and understand operator's manual. GENERAL POWER TOOL SAFETY
More informationMULTI PURPOSE SAW 500W INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au WHAT S IN THE BOX MSW Multi-purpose Saw. Blades x 3.
WHAT S IN THE BOX MULTI PURPOSE SAW 500W INSTRUCTION MANUAL SPECIFICATIONS Input: Voltage: No Load Speed: Stroke Length: Blade Fitment: Cutting Capacity: Weight: ozito.com.au 500W 230-240V ~ 50Hz 500-3000
More informationE-DRIV MD-Series DC Torque Control System Calibration Procedure
Revision: 1.1 July 05, 2017 E-DRIV MD-Series DC Torque Control System Calibration Procedure www.mountztorque.com 1080 N 11 th St - San Jose CA 95112-408.292.2214 1 GENERAL SAFETY RULES WARNING! Read and
More informationBENCH GRINDER MODEL NO. OZBG150WA
BENCH GRINDER 150mm MODEL NO. OZBG150WA OPERATING INSTRUCTIONS To view our entire range visit www.ozito.com.au SPECIFICATIONS MODEL NO. OZBG150WA Input Power: 150W Input Voltage: 230V ~ 50Hz No Load Speed:
More information20V Cordless Shrub Shear & Grass Shear P02 P10 P15 WG801 WG801.9
P02 P0 P5 WG80 WG80.9 2 WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth
More informationModel TC-20. Tube Cut-Off Machine. Operator s Manual REV H
Model TC-20 Tube Cut-Off Machine Operator s Manual 90-2333 REV H Scientific Systems, Inc. 349 N. Science Park Road State College, PA 16803 www.ssihplc.com Phone: 800-441-4752 Fax: 814-238-7532 Email: sales@ssihplc.com
More informationCordless Hedge Trimmer Taille-haies sans fil Cortasetos Inalámbrico EN F ES P05 P12 P20 WG255 WG255.1 WG255.9 WG275 WG275.9 WG280 WG280.
Taille-haies sans fil Cortasetos Inalámbrico F ES P05 P12 P20 WG255 WG255.1 WG255.9 WG275 WG275.9 WG280 WG280.9 2 5 3 6 4 7 1 8 9 A B1 1 2 1 3 B2 C C B2 1 2 D1 D2 D3 E 1. BATTERY PACK* 2. REAR HANDLE
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill DF330D 009329 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DF330D Steel 0 mm Capacities Wood
More information20V Lithium-Ion Cordless Combi Drill JCB-CD20LIBL
Safety and operating manual 20V Lithium-Ion Cordless Combi Drill JCB-CD20LIBL ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to
More informationInstructions manual / Position Controller 1. GY-G Series INSTRUCTIONS MANUAL
Instructions manual / Position Controller 1 GY-G Series INSTRUCTIONS MANUAL Instructions manual / GY-G Series 2 IMPORTANT The tool delivered with this manual may been modified for specific needs. In that
More informationCordless Impact Wrench
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Impact Wrench DTW50 DTW5 007450 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DTW50 DTW5 Capacities Standard
More informationENGLISH (Original instructions) INSTRUCTION MANUAL. Cordless Angle Drill DDA340 DDA350. IMPORTANT: Read Before Using.
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Angle Drill DDA340 DDA350 008950 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DDA340 DDA350 Capacities
More informationOPERATOR'S MANUAL M18 HKP M18 6-TON KNOCKOUT TOOL WARNING. Cat. No. To reduce the risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL Cat. No. M18 HKP M18 6-TON KNOCKOUT TOOL WARNING To reduce the risk of injury, user must read and understand operator's manual. GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety
More informationChallenge Xtreme 18V CORDLESS HAMMER DRILL
Challenge Xtreme 18V CORDLESS HAMMER DRILL Assembly Manual-Original Instructions After Sales Support UK/Ireland 0345 640 0800 Web WWW.ARGOS.CO.UK Important - Please read these instructions fully before
More information- Keep children and other people away while operating the rivet tool. Distractions can cause you to lose control of the tool.
PLEASE SPEND 5 MINUTES READING THESE INSTRUCTIONS BEFORE USING YOUR NEW BATTERY RIVET TOOL. TRUST US, IT WILL SAVE YOU TIME AND INCONVENIENCE IN THE LONG RUN. Please read the following safety information
More informationFMC641
3 8 4 7 2 1 6 5 www.stanley.eu FMC641 ENGLISH (Original instructions) 5 6 5 10 A 11 B 13 4 13 3 C1 C2 D 1 2 D 2 (Original instructions) ENGLISH Intended use Your Stanley Fat Max FMC641 impact wrench has
More informationCORDLESS COMBI DRILL JCB-CD18Li
SAFETY AND OPERATING MANUAL CORDLESS COMBI DRILL JCB-CD18Li Original Instructions General Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
More information