2014 Gasket Catalogue REGISTERED QMS. ISD

Transcription

1 2014 ISO 9001 REGISTERED QMS G A S K E T FA B R I C AT O R S A S S O C I AT I O N ISD

2 Table of Contents Introduction 3 Manufacturing 4 LaserQC 4 Materials 5 Composite Materials Chemical Compatibility 14 Equipment 15 Custom Gaskets 16 Pipe Flange Gaskets 17 Ring Joint Gaskets 22 Spiral Wound Gaskets 27 Kammprofile 34 Isolation Kits 35 Studs & Nuts 36 Bolt Protectors 42 Thread Protectors 43 Braided Packing 44 Joint Sealant 47 Redline Gauge Glass 48 Additional Products 50 Mud Plug Kits 50 Screw Packing 50 Fibre Glass Rope 50 Boiler Gaskets 51 Piper Rollers 51 PTFE Tape 51 Tank Stripping 52 Chime Lap Gaskets 52 Fillet Strip 52 Service 53 Field Service 53 After-Hours 53 Gasket Kits 53 Hi-Tech Seals 54 Rubber & Plastic Machining 55 Custom Cast Urethane 56 Hi-Tech Seals Components 58 2

3 Manufacturing Introduction to Hi-Tech Gaskets Hi-Tech Gaskets was founded in 2012 as a subsidiary of Hi-Tech Seals. We are guided by the same founding principles of quality, inventory and service. Since our establishment, we have invested substantially into equipment that provides a key service advantage. ISO 9001 Registered QMS At Hi-Tech Gaskets, we are committed to our Quality Management System (QMS). The four main goals of our policy include: Hi-Tech Gaskets shall distribute and/or manufacture a quality product that will meet our customers requirements and expectations Hi-Tech Gaskets shall strive to continually improve the effectiveness of the Quality Management System Hi-Tech Gaskets Quality Policy shall be communicated and understood at all levels of the organization Hi-Tech Gaskets Quality Policy and Quality Objectives will be reviewed for effectiveness and accuracy during the Annual Management Review ISO 9001 REGISTERED QMS 3

4 Manufacturing LaserQC Hi-Tech Gaskets employs a Virtek LaserQC 1200 machine. The LaserQC assists in reverse engineering, quality inspection/control and statistical process control. 2D Reverse Engineering The LaserQC 1200 aids in the reverse engineering of existing parts or templates. This process starts with the scanning of existing parts or templates to capture their complete profile. The data is stored as a CAD data file. From this file our drafting department can manipulate the scanned data to remove flaws and optimize the tolerances for production. Our drafting team can then export the file directly to our flashcutter or waterjet for rapid gasket production. Quality Inspection / Control The LaserQC is also utilized to complete manufacturing inspections. It captures over 500 data points a second, while maintaining a tolerance within ± 0.05mm (0.002 ). The system then compares your production drawing to your final product. The scanned profile is displayed in a color-coded outline, which is used to indicate what, if any, of the profile scanned is out of tolerance. Statistical Process Control Inspection data from the LaserQC 1200 is saved and can be used to generate reports for traceability and statistical analysis meeting quality requirements. This information can also be used internally to make production improvements to ensure quality products and reduced lead times. 4

5 Manufacturing Materials Hi-Tech Gaskets stocks a large inventory of rubber, plastic, composite and metal materials. Our inventory is available for both fabrication and direct for sale. Sheet material can be cut to our customer s desired length. Rubber and Plastic Sheet Red Rubber (SBR), Neoprene, Silicone, White Nitrile, Nitrile, Highly Saturated Nitrile, Cork/Nitrile, Fluorocarbon, EPDM, Neo-Nylon, PTFE, expanded PTFE, UHMW-PE, Vegetable fibre/plant fibre, Gum Rubber Thickness: 1/64, 1/32, 1/16, 1/8, 3/16, 1/4 Sheet Size: 5 x 66 Composite Non-Asbestos BA-U, BA-50, BA-CF, BACF-4000 Thickness: 1/64, 1/32, 1/16, 1/8 Sheet Size: 3 x 3, 5 x 5, 5 x 15 Composite Flexible Graphite Grafilit SF, Grafilit SL, Grafilit SP Thickness: 1/64, 1/32, 1/16, 1/8 Sheet Size: 5 x 5 Metal Mild Steel, Stainless Steel 304, Stainless Steel 316L, Aluminum, Copper Thickness: 1/32, 1/16, 1/8, 1/4, 1/2, 3/4, 1, 1-1/4, 1-1/2, 1-3/4, 2 Sheet Size: 4 x 8, 5 x 10 5

6 Manufacturing Materials Elastomer Materials - Commercial Grade - Industrial Grade Ethylene-Propylene (EPDM) Technical Data ASTM General Properties & Applications: Excellent resistance to heat, ozone, sunlight, water and steam Good flexibility at low temperatures Hardness (Shore A) D Tensile Strength (psi) D min. Elongation (%) D min. Compression Set D395B 70 C 50% max. Temperature -40 C to 121 C -40 F to 250 F Fluorocarbon Technical Data ASTM General Properties & Applications: Excellent resistance to heat, oil and chemicals Not suitable for steam or hot water over 100 C Hardness (Shore A) D Tensile Strength (psi) D Elongation (%) D Temperature -18 C to 204 C 0 F to 399 F Highly Saturated Nitrile General Properties & Applications: Improved temperature range over standard Nitrile Good mechanical properties Used in many oilfield and chemical industry applications Technical Data ISO Hardness (Shore A) ISO Tensile Strength (psi) ISO min. Elongation (%) ISO min. Temperature -45 C to 160 C -49 F to 320 F Neoprene Technical Data ASTM General Properties & Applications: Good resistance to weather, ozone, natural aging, alkalis and acids Moderate oil and gas resistance Hardness (Shore A) D Tensile Strength (psi) D min. Elongation (%) D min. Temperature -29 C to 88 C -20 F to 190 F 6

7 Manufacturing Materials Elastomer Materials - Commercial Grade - Industrial Grade Neoprene Technical Data ASTM General Properties & Applications: Improved tensile strength and elongation over the 60 durometer commercial grade Neoprene Hardness (Shore A) D Tensile Strength (psi) D min. Elongation (%) D min. Compression Set D395B 100 C 80% max. Temperature -29 C to 88 C -20 F to 190 F Neo-Nylon Technical Data ASTM General Properties & Applications: Neoprene material with a woven nylon cloth insert. Maintains the properties of Neoprene, but with added puncture resistance, stability and tear strength Hardness (Shore A) D Tensile Strength (psi) D Elongation (%) D Temperature -20 C to 77 C -4 F to 170 F Nitrile General Properties & Applications: Strong resistance to petroleum based hydraulic fluids Poor resistance to ozone and sunlight Good for applications where oil resistance is a concern Technical Data ASTM Hardness (Shore A) D Tensile Strength (psi) D min. Elongation (%) D min. Compression Set D395B C 40% max. Temperature -34 C to 88 C -30 F to 190 F 7

8 Manufacturing Materials Elastomer Materials - Commercial Grade - Industrial Grade Red Rubber (SBR) General Properties & Applications: Economical non-critical applications Poor resistance to ozone and sunlight, oil, gasoline and hydrocarbon solvents Low pressure applications Technical Data ASTM Hardness (Shore A) D Tensile Strength (psi) D min. Elongation (%) D min. Temperature -29 C to 82 C -20 F to 180 F Red Rubber (SBR) - Fabric Surface General Properties & Applications: Economical non-critical applications Poor resistance to ozone and sunlight, oil, gasoline and hydrocarbon solvents Improved pressure resistance over homogeneous red rubber Technical Data ASTM Hardness (Shore A) D Tensile Strength (psi) D min. Elongation (%) D min. Compression Set D395B 70 C 50% max. Temperature -29 C to 82 C -20 F to 180 F Silicone General Properties & Applications: Good heat and low temperature resistance Good weather and ozone resistance Technical Data ASTM Hardness (Shore A) D Tensile Strength (psi) D min. Elongation (%) D min. Temperature -54 C to 200 C -65 F to 392 F Approvals: FDA grade 8

9 Manufacturing Materials Thermoplastic Materials PTFE General Properties & Applications: Composed of 100% virgin PTFE Near universal chemical resistance Technical Data ASTM Hardness (Shore D) 60 Tensile Strength (psi) D min. Elongation (%) D min. Compression Strength (psi) D min. Temperature Max. Continuous 260 C / 500 F Expanded PTFE General Properties & Applications: Composed of 100% virgin PTFE Near universal chemical resistance Withstands higher compressive loads than standard PTFE sheet Technical Data ASTM Compressibility F36 68% Recovery F36 12% Temperature Limit -268 C to 316 C -450 F to 600 F Pressure Limit 207 bar / 3000 psi Approvals: FDA USDA UHMW-PE General Properties & Applications: No moisture absorption Self-lubricating Chemical, corrosion and wear resistance Technical Data ASTM Hardness (Shore D) D Tensile Strength (psi) D Elongation (%) D Compressive Strength (psi) D Temperature -250 C to 80 C -418 F to 176 F Approvals: FDA USDA 3-A Dairy 9

10 Manufacturing Materials Metal Materials With the use of our waterjet, we are able to cut various types of metal components from 1/64 shims up to 2 thick plate. Metal Identification Hi-Tech Gasket has a Bruker S1 Sorter (XRF spectrometer) capable of instantly identifying the alloy composition of a metal component. The XRF spectrometer device can be utilized for both inspection and identification purposes. Once a metal composition is identified we can recommend a replacement gasket. Identification is key for flange and gasket design, as your gasket material must be composed of a material more willing to deform under load, to prevent damage of your flange. Stainless Steel 304 Stainless Steel 316L General Properties & Applications: General Properties & Applications: Minimum 18% Chromium, 8% Nickel Most widely used grade of stainless steel Good corrosion resistance 16-18% Chromium, 10-14% Nickel Higher atmospheric resistance than SS304 Higher creep strength at elevated temperatures Improved corrosion resistance Additional Materials: Upon request, Hi-Tech Gaskets can produce parts in mild steel 1016, 1020, 1025; aluminum 6061; aluminum bronze; brass; bronze; and alloy steel 4140, and

11 Manufacturing Materials Composite Materials Non-Asbestos BA-U - Aramide Fibres, Nitrile General Properties & Applications: Good chemical, mechanical & thermal properties General purpose material Approvals: DIN-DVGW (DIN 3535/6) SVGW (DIN 3535/6) SVGW (W/TPW) HTB (DVGW VP 401) DVGW KTW DVGW W270 WQc/WRAS BAM (Oxygen) Germanischer Lloyd CRS- Croatian Register of Shipping BS 7531 Grade Y TA-Luft (VDI 2440) Technical Data Compressibility ASTM F36/J 8% Recovery ASTM F36/J 55% Tensile Strength DIN MPa Stress Resistance DIN h, 300 C, 50 MPa 22 MPa 16h, 175 C, 50 MPa 28 MPa Thickness Increase ASTM F 146 ASTM Fuel B, 5h, 23 C 5% Oil IRM 903, 5h, 150 C 5% Specific Leakage Rate DIN 3535/ mg/(s m) Max Operating Conditions Peak Temp 350 C / 662 F Continuous Temp. 250 C / 482 F With Steam Temp. 200 C / 392 F Pressure 100 bar / 1450 psi BA-50 - Aramide Fibres, Nitrile General Properties & Applications: Good chemical resistance Suitable for higher loading Gas, food, chemical industry Approvals: DIN-DVGW (DIN 3535/6) SVGW (DIN 3535/6) SVGW (W/TPW) DVGW KTW WQc/WRAS Germanischer Lloyd CRS- Croatian Register of Shipping TA-Luft (VDI 2440) Technical Data Compressibility ASTM F36/J 8% Recovery ASTM F36/J 45% Tensile Strength DIN MPa Stress Resistance DIN h, 300 C, 50 MPa 20 MPa 16h, 175 C, 50 MPa 25 MPa Thickness Increase ASTM F 146 ASTM Fuel B, 5h, 23 C 10% Oil IRM 903, 5h, 150 C 10% Specific Leakage Rate DIN 3535/ mg/(s m) Max Operating Conditions Peak Temp 280 C / 536 F Continuous Temp. 220 C / 428 F With Steam Temp. 180 C / 356 F Pressure 80 bar / 1160 psi 11

12 Manufacturing Materials Composite Materials BA-CF - Carbon Fibres, Nitrile General Properties & Applications: Excellent resistance to steam Chemical and petrochemical industry Approvals: DIN-DVGW (DIN 3535/6) SVGW (DIN 3535/6) HTB (DVGW VP 401) DVGW KTW BAM (Oxygen) CRS- Croatian Register of Shipping BS 7531 Grade Y BS 7531 Grade X Technical Data placeholders Compressibility ASTM F36/J 9% Recovery ASTM F36/J 55% Tensile Strength DIN MPa Stress Resistance DIN h, 300 C, 50 MPa 25 MPa 16h, 175 C, 50 MPa 30 MPa Thickness Increase ASTM F 146 Oil IRM 903, 5h, 150 C 7% Specific Leakage Rate DIN 3535/ mg/(s m) Max Operating Conditions Peak Temp 400 C / 752 F Continuous Temp. 300 C / 572 F With Steam Temp. 280 C / 536 F Pressure 100 bar / 1450 psi BACF Carbon Fibres, Nitrile General Properties & Applications: Environmentally friendly gasket material with enhanced resistance to steam & strong alkaline media Chemical, pulp & paper industry; saturated steam distribution Approvals: DIN-DVGW (DIN 3535/6) HTB (DVGW VP 401) TARC/MRPRA TA Luft (VDI 2440) BS 7531 Grade X Technical Data Density DIN g/cm 3 Compressibility ASTM F36/J 6-11% Recovery ASTM F36/J >55% Tensile Strength DIN MPa Stress Resistance DIN h, 300 C, 50 MPA 30 MPa 16h, 175 C, 50 MPA 35 MPa Thickness Increase ASTM F 146 ASTM Fuel B, 5h, 20 C 5% Oil IRM 903, 5h, 150 C 5% Specific Leakage Rate DIN 3535/ mg/(s m) Compression Modulus DIN At Room Temp: KSW % At Elevated Temp: WRW/200 C % Recovery R DIN mm Max Operating Conditions Peak Temp. 440 C / 824 F Continuous Temp. 350 C / 662 F With Steam Temp. 280 C / 536 F Pressure 120 bar / 1740 psi 12

13 Manufacturing Materials Composite Materials Flexible Graphite Grafilit SF Grafilit SL Grafilit SP General Properties & Applications: General Properties & Applications: General Properties & Applications: Flexible graphite without insert Ideal for the food industry and when in contact with drinking water Laminated with flat stainless-steel insertion (AISI 316; 0.05 mm) Suitable for wide range of applications where higher operating pressures are present (i.e. gas supply) Mechanically bonded to a tonged stainless-steel insertion (AISI 316; 0.1 mm) Used in chemical & petroleum ind., at high surface loads or high operating pressures Approvals: Approvals: Approvals: DIN-DVGW (DIN 3535/6) HTB (DVGW VP 401) DVGW KTW BAM Germanischer Lloyd DIN-DVGW (DIN 3535/6) HTB (DVGW VP 401) DVGW KTW BAM Technical Data DIN-DVGW (DIN 3535/6) HTB (DVGW VP 401) DVGW KTW BAM Germanischer Lloyd Fire safe API 607 SF SL SP DIN g/cm3 1.0 g/cm3 1.0 g/cm3 Compressibility Recovery ASTM F36 ASTM F36 45% 13% 45% 13% 35% 17% Stress Resistance (16h, 300 C) DIN N/mm2 49 N/mm2 49 N/mm2 Density Compression Modulus At Room Temp.: At Elevated Temp.: At Elevated Temp.: 38% 41% 32% 0.9% 1.1% 1.2% 5.0% 4.5% 4.5% 4.5% 4.0% 4.0% DIN mm mm mm DIN 3535/6 DIN FSA NMG FSA NMG C / 842 F 2500 C / 4532 F -200 C / -328 F 80 bar / 1160 psi <0.02 mg/(s m) <1% <50 ppm <50 ppm 450 C / 842 F 700 C / 1292 F -200 C / -328 F 100 bar / 1450 psi <0.05 mg/(s m) <1% <50 ppm <50 ppm 450 C / 842 F 700 C / 1292 F -200 C / -328 F 200 bar / 2900 psi <0.05 mg/(s m) <1% <50 ppm <50 ppm WSW/300 C Percentage Creep Relaxation At Room Temp.: DIN KSW DIN KRW WRW/300 C Recovery R Max Operating Conditions Continuous Max. Temp. Air or oxidizing atmosphere Reducing or inert atmosphere Continuous use min. Temp. Continuous use max. Pressure Permeability to Nitrogen (40 bar, RT) Ash Content Chloride Content Fluoride Content 13

14 Manufacturing Composite Materials Chemical Compatibility R - Recommended, C- Consult a Sales Representative, N- Not Recommended, NA - No Available Data BA-u BA-50 BA-CF BACF-4000 Grafilit Acetamide R R R R R Acetic Acid 10% R R R R NA Acetic Acid 100% R R R R R Acetic Ester C C C C R Acetone C C C C R Acetylene R R R R R Adipic Acid R R R R R Air R R R R R Alum R R R R R Aluminum Acetate R R R R R Aluminum Chlorate R R R R N Aluminum Chloride R R R R N Ammonia R C R R R Ammonium Bicaronate R R R R R Ammonium Chloride R R R R R Ammonium Hydroxide R C R R R Amyl Acetate C C C C R Aniline N N N N R Asphalt R R R R R Barium Chloride R R R R R Benzene C C C C R Benzoic Acid R R R R R Boric Acid R R R R R Blast Furnance Gas NA NA NA NA R Borax R R R R R Butane R R R R R Butyl Alcohol R R R R R Butyric Acid R R R R R Calcium Chloride R R R R R Calcium Hydroxide R R R R R Carbon Disulphide N N N N R Carbon Dioxide R R R R R Chloroform C C C C R Chlorine, Dry C N C C C Chlorine, Wet C N C C C Chromic Acid N N N N N Citric Acid R R R R R Copper Acetate R R R R R Creosote N N N N R Cresol C C C C R Cyclohexanol R R R R R Cyclohexanone C N C C R Decalin R R R R R Dibenzyl Ether N N N N R Dimethyl Formamide N N N N R Dowtherm C C C C R Ethane R R R R R Ethyl Acetate C C C C R Ethyl Alcohol R R R R R Ethyl Chloride C C C C R Ethylene R R R R R Ethylene Glycol R C R R R Formic Acid 10% R R R R NA Formic Acid 85% R C R R NA BA-u BA-50 BA-CF BACF-4000 Grafilit Formic Acid NA NA NA NA R Formaldehyde R R R R R Freon 12 R R R R R Freon 22 C C C C R Fuel Oil R R R R R Gasoline R R R R R Glycerin R R R R R Heptane R R R R R Hydraulic Oil (Mineral) R R R R R Hydraulic Oil (Phosphate Esther Type) C C C C R Hydraulic Oil (Glycol Base) R R R R R Hydrazine R R R R R Hydrochloric Acid 20% C N C C C Hydrochloric Acid 36% N N N N NA Hydrofluoric Acid 10% N N N N NA Hydrofluoric Acid 40% N N N N N Hydrogen R R R R R Isobutane R R R R R Isoctane R R R R NA Isopropyl Alcohol R R R R R Kerosene R R R R R Lead Acetate R R R R R Lead Arsenate R R R R R Magnesium Sulphate R R R R R Malic Acid R R R R R Methane R R R R R Methanol R R R R R Methyl Chloride C C C C R Methylene Dichloride N N N N R Methyl Ethyl Ketone C C C C R Milk R R R R R Mineral Oil Type ASTM No.1 R R R R R Naphtha R R R R R Nitric Acid 20% N N C C C Nitric Acid 40% N N N N C Nitric Acid 96% N N N N N Nitrobenzene N N N N R Nitrogen R R R R R Octane R R R R R Oleic Acid R R R R R Oleum N N N N N Oxalic Acid C C C C R Oxygen R R R R R Palmitic Acid R R R R R Pentane R R R R R Percholoethylene C C C C R Phenol N N N N R Phosphoric Acid C C C C C Potassium Acetate R R R R R Potassium Bicarbonate R R R R R Potassium Carbonate R R R R R Potassium Chloride R R R R R Potassium Dichromate R R R R N BA-u BA-50 BA-CF BACF-4000 Grafilit Potassium Hydroxide C C R R C Potassium Iodide R R R R R Potassium Nitrate R R R R C Potassium Permanganate R R R R R Propane R R R R R Pyridine N N N N C R 134a R R R R NA Salicylic Acid R R R R R Silicone Oil R R R R R Soap R R R R R Sodium Aluminate R R R R R Sodium Bicarbonate R R R R R Sodium Bisuphite R R R R R Sodium Carbonate R R R R R Sodium Chloride R R R R R Sodium Cyanide R R R R R Sodium Hydroxide C C R R C Sodium Sulphate R R R R R Sodium Sulphide R R R R R Starch R R R R R Steam R R R R R Stearic Acid R R R R R Sugar R R R R R Sulphuric Acid 20% N N C C C Sulphuric Acid 96% N N N N N Tar R R R R R Tartaric Acid R R R R R Toluene R R R R R Transformer Oil R R R R R Trichlorethylene C C C C R Water R R R R R White Spirit R R R R R Xylene C C R C R 14

15 Manufacturing Equipment Flashcutter Hi-Tech Gaskets flashcutter is capable of utilizing CAD renderings to quickly produce gaskets in rubber, plastic and composite materials. The flashcutter s surface area can accommodate material up to 5 x 10 (1550 mm x 3050 mm). Gaskets are cut through a rapid vertical reciprocating motion. The cutting motion produces a cleaner finished part, avoiding compression marks found on die-cut gaskets. The flashcutter s vacuum surface holds the sheet material in place preventing the movement of parts during production. This enables the flashcutter to maintain exceptional tolerances during production. Waterjet The Omax waterjet further expands our manufacturing capabilities. The waterjet cuts the standard composite and rubber materials, but also allows us to manufacture metal gaskets up to 2 thick. The waterjet working surface area is 60 x 135. Gaskets that require a larger work surface area can be produced in a dovetail style. Die Cut Hi-Tech Gaskets utilizes both a clicker press and roller press to produce die cut gaskets. Dies are manufactured locally and stored in house. Die Cut - Round Gaskets - up to 48 Die Cut - Oblong Gaskets -up to 33 x 66 Hand Cut For cost effective small runs, Hi-Tech Gasket produces hand cut gaskets. Dimensional capabilities include: Hand Cut - Round Gaskets - up to 36 Hand Cut - Oblong Rubber Gaskets - up to 48 x virtually endless Hand Cut - Oblong Non-asbestos Gaskets - Up to 60 x

16 Custom Gaskets Custom Gaskets Custom gaskets can be manufactured based on a sample or from metal dimensions. If you are providing a sample, our team can rapidly plot the dimensions of your gasket on our LaserQC. Our drafting team will adjust the dimensions to remove flaws, then send the CAD file to our production team. From there, we will select the best material from our extensive inventory of sheet stock. Gaskets can be manufactured in as little as 24 hours, upon request. Rush charges may apply. Request a quote: Hi-Tech Gaskets at info@hitechgaskets.com By phone at Hi-Tech Gaskets: At any of our Hi-Tech Seals locations If you are providing dimensions, complete the appropriate Custom Gasket Measurement Sheet found on our website at or. Custom Gasket Measurement Sheet: Manway, D-Style, Firetube Once completed, the sheet can then be faxed or ed to a Hi-Tech representative. Fax: info@hitechgaskets.com 16

17 Pipe Flange Gaskets Raise Faced Gasket (RFG) Full Face Gasket (FFG) Product Description: Hi-Tech Gaskets utilizes an extensive inventory of sheet material to rapidly manufacture gaskets for ASME B16.21 pipe flanges and flange fittings. Sizes are available for class 150#, 300#, 400#, 600#, 900#, 1500# and 2500#. If you have a custom size pipe flange gasket, Hi-Tech Gaskets can manufacture replacement gaskets from a sample or metal dimensions. Part Number: - Nominal Size RFG - Raised Faced Gasket FFG - Full Face Gasket # Class Material Thickness Example: RFG RR raised faced gasket - 4 nom., 900#, red rubber - 1/8 thick - 4-1/2 I.D., 8-1/8 O.D. 17

18 Pipe Flange Gaskets Standard 150# forged Steel Pipe Flange Gasket Dimensions Raised Face Gasket Full Face Gasket Nominal Size OD ID OD ID No. Bolts Hole Diameter B.C.D. 1/2 1-7/8 27/32 3-1/2 27/32 4 5/8 2-3/8 3/4 2-1/4 1-1/16 3-7/8 1-1/16 4 5/8 2-3/ /8 1-5/16 4-1/4 1-5/16 4 5/8 3-1/8 1-1/ /32 4-5/8 1-21/32 4 5/8 3-1/2 1-1/2 3-3/8 1-29/ /32 4 5/8 3-7/ /8 2-3/ /8 4 3/4 4-3/4 2-1/2 4-7/8 2-7/ /8 4 3/4 5-1/ /8 3-1/2 7-1/2 3-1/2 4 3/ /2 6-3/ / / /8 4-1/ /2 8 3/4 7-1/ /4 5-9/ /16 8 7/8 8-1/ /4 6-5/ /8 8 7/8 9-1/ /8 13-1/2 8-5/8 8 7/8 11-3/ /8 10-3/ / / /8 12-3/ / / /8 18-3/ / / /8 21-1/ / /4 22-3/ / / / / /8 29-1/2 Standard 300# forged Steel Pipe Flange Gasket Dimensions Raised Face Gasket Full Face Gasket Nominal Size OD ID OD ID No. Bolts Hole Diameter B.C.D. 1/2 2-1/8 27/32 3-3/4 27/32 4 5/8 2-5/8 3/4 2-5/8 1-1/16 4-5/8 1-1/16 4 3/4 3-1/ /8 1-5/16 4-7/8 1-5/16 4 3/4 3-1/2 1-1/4 3-1/4 1-21/32 5-1/4 1-21/32 4 3/4 3-7/8 1-1/2 3-3/4 1-29/32 6-1/8 1-29/32 4 7/8 4-1/ /8 2-3/8 6-1/2 2-3/8 8 3/ /2 5-1/8 2-7/8 7-1/2 2-7/8 8 7/8 5-7/ /8 3-1/2 8-1/4 3-1/2 8 7/8 6-5/8 3-1/2 6-1/ /8 7-1/ /8 4-1/ /2 8 7/8 7-7/ /2 5-9/ /16 8 7/8 9-1/ /8 6-5/8 12-1/2 6-5/8 12 7/8 10-5/ /8 8-5/ / /4 10-3/4 17-1/2 10-3/ /8 15-1/ /8 12-3/4 20-1/2 12-3/ /4 17-3/ / /4 20-1/ / / /8 22-1/ / /8 24-3/ / / / / /8 32 B.C.D. - Bolt Circle Diameter 18

19 Pipe Flange Gaskets Standard 400# Pipe Flange Gasket Dimensions Raised Face Gasket Full Face Gasket Nominal Size OD ID OD ID No. Bolts Hole Diameter B.C.D. 1/2 2-1/8 27/32 3-3/4 27/32 4 5/8 2-5/8 3/4 2-5/8 1-1/16 4-5/8 1-1/16 4 3/4 3-1/ /8 1-5/16 4-7/8 1-5/16 4 3/4 3-1/2 1-1/4 3-1/4 1-21/32 5-1/4 1-21/32 4 3/4 3-7/8 1-1/2 3-3/4 1-29/32 6-1/8 1-29/32 4 7/8 4-1/ /8 2-3/8 6-1/2 2-3/8 8 3/ /2 5-1/8 2-7/8 7-1/2 2-7/8 8 7/8 5-7/ /8 3-1/2 8-1/4 3-1/2 8 7/8 6-5/8 3-1/2 6-3/ / / / / /8 5-9/ / / /4 6-5/8 12-1/2 6-5/ / / / / /8 10-3/4 17-1/2 10-3/ /4 15-1/ /2 12-3/4 20-1/2 12-3/ /8 17-3/ /8 20-1/ / / /2 22-1/ / /2 24-3/ / / / / /8 32 Standard 600# Pipe Flange Gasket Dimensions Raised Face Gasket Full Face Gasket Nominal Size OD ID OD ID No. Bolts Hole Diameter B.C.D. 1/2 2-1/8 27/32 3-3/4 27/32 4 5/8 2-5/8 3/4 2-5/8 1-1/32 4-5/8 1-1/16 4 3/4 3-1/ /8 1-5/16 4-7/8 1-5/16 4 3/4 3-1/2 1-1/4 3-1/4 1-21/32 5-1/4 1-21/32 4 3/4 3-7/8 1-1/2 3-3/4 1-29/32 6-1/8 1-29/32 4 7/8 4-1/ /8 2-3/8 6-1/2 2-3/8 8 3/ /2 5-1/8 2-7/8 7-1/2 2-7/8 8 7/8 5-7/ /8 3-1/2 8-1/4 3-1/2 8 7/8 6-5/8 3-1/2 6-3/ / /8 4-1/2 10-3/4 4-1/ / /2 5-9/ / /8 10-1/ /2 6-5/ / /8 11-1/ /8 8-5/8 16-1/2 8-5/ /4 13-3/ /4 10-3/ / / / / /8 19-1/ / / /2 20-3/ / /8 23-3/ / / /4 25-3/ / /4 28-1/ / B.C.D. - Bolt Circle Diameter 19

20 Pipe Flange Gaskets Standard 900# Pipe Flange Gasket Dimensions Raised Face Gasket Full Face Gasket Nominal Size OD ID OD ID No. Bolts Hole Diameter B.C.D. 1/2 2-1/2 27/32 4-3/4 27/32 4 7/8 3-1/4 3/4 2-3/4 1-1/16 5-1/8 1-1/16 4 7/8 3-1/ /8 1-5/16 5-7/8 1-5/ /4 3-1/2 1-21/32 6-1/4 1-21/ /8 1-1/2 3-7/8 1-29/ / /8 4-7/ /8 2-3/8 8-1/2 2-3/ /2 2-1/2 6-1/2 2-7/8 9-5/8 2-7/ /8 7-1/ /8 3-1/2 9-1/2 3-1/ /2 3-1/ /8 4-1/2 11-1/2 4-1/ /4 9-1/ /4 5-9/ /4 5-9/ / /8 6-5/ / /4 12-1/ /8 8-5/8 18-1/2 8-5/ /2 15-1/ /8 10-3/4 21-1/2 10-3/ /2 18-1/ /8 12-3/ / / / / / / / /4 24-1/ / / / /8 29-1/ /8 35-1/2 Standard 1500# Pipe Flange Gasket Dimensions Raised Face Gasket Full Face Gasket Nominal Size OD ID OD ID No. Bolts Hole Diameter B.C.D. 1/2 2-1/2 27/32 4-3/4 27/32 4 7/8 3-1/4 3/4 2-3/4 1-1/16 5-1/8 1-1/16 4 7/8 3-1/ /8 1-5/16 5-7/8 1-5/ /4 3-1/2 1-21/32 6-1/4 1-21/ /8 1-1/2 3-7/8 1-29/ / /8 4-7/ /8 2-3/8 8-1/2 2-3/ /2 2-1/2 6-1/2 2-7/8 9-5/8 2-7/ /8 7-1/ /8 3-1/2 10-1/2 3-1/ / / /8 4-1/2 12-1/4 4-1/ /8 9-1/ / /4 5-9/ /8 11-1/ /8 6-5/8 15-1/2 6-5/ /2 12-1/ /8 8-5/ / /4 15-1/ /8 10-3/ / /2 12-3/4 26-1/2 12-3/ /8 22-1/ / / / / / /8 27-3/ / /8 30-1/ / / /8 32-3/ / /8 39 B.C.D. - Bolt Circle Diameter 20

21 Pipe Flange Gaskets Standard 2500# Pipe Flange Gasket Dimensions Raised Face Gasket Full Face Gasket Nominal Size OD ID OD ID No. Bolts Hole Diameter B.C.D. 1/2 2-3/4 27/32 5-1/4 27/32 4 7/8 3-1/2 3/ /16 5-1/2 1-1/16 4 7/8 3-3/ /8 1-5/16 6-1/4 1-5/ /4 1-1/4 4-1/4 1-21/32 7-1/4 1-21/ /8 1-1/2 4-5/8 1-29/ / /4 5-3/ /4 2-3/8 9-1/4 2-3/ /8 6-3/4 2-1/2 6-5/8 2-7/8 10-1/2 2-7/ /4 7-3/ /4 3-1/ / / / /4 4-1/ / /8 10-3/ / /2 5-9/ /8 12-3/ /2 6-5/ / /8 14-1/ /4 8-5/8 21-3/4 8-5/ /8 17-1/ /4 10-3/4 26-1/2 10-3/ /8 21-1/ /8 12-3/ / /8 24-3/ B.C.D. - Bolt Circle Diameter 21

22 Ring Joint Gaskets Materials: Temperature Stainless Steel C to 460 C Stainless Steel C to 420 C Low Carbon Steel -100 C to 500 C Soft Iron -100 C to 500 C * Stainless steel 316 and 304 can exceed continuous operating temperatures (Up to 760C), however this may result in inter-granular corrosion. Please consult a Hi-Tech Gaskets' representative. R Oval R Octagonal RX BX Polyurethane Test Gasket Rubber Coated Test Gasket Product Description: Hi-Tech Gaskets stocks ring joint gaskets in R oval, R octagonal, RX, and BX styles. Dimensions for ring joint gaskets are in accordance to ASTM B16.20, API 6A and ASME B16.5/B In addition, Hi-Tech Gaskets supplies valve test gaskets in polyurethane styles and rubber coated styles. Part Numbers: RTJ - Style Dash No. Materials: If R-Style: Stainless Steel 316 OCT - Octagonal Stainless Steel 304 OVAL - Oval S - Low Carbon Steel D - Soft Iron Example: RTJ - R OVAL - ring type joint gasket - R oval profile, size 20, stainless steel

23 Ring Joint Gaskets R Series R series ring type joint gaskets are available in oval and octagonal designs. The oval design can be used in older round bottom gland designs, while both can be used in a flat bottom design. R Series are available up to 5,000 PSI. R Oval R Octagonal Pipe Size Dash No. at Class Rating /2 - R11 - R11 R12 R12 R13 3/4 - R13 - R13 R14 R14 R16 1 R15 R16 - R16 R16 R16 R18 1-1/4 R17 R18 - R18 R18 R18 R21 1-1/2 R19 R/RX20 - R/RX20 R/RX20 R/RX20 R/RX23 2 R22 R/RX23 - R/RX23 R/RX24 R/RX24 R/RX26 2-1/2 R/RX25 R/RX26 - R/RX26 R/RX27 R/RX27 R28 3 R29 R/RX31 - R/RX31 R/RX31 R/RX35 R32 3-1/2 R33 R34 - R R36 R/RX37 R/RX37 R/RX37 R/RX37 R/RX39 R38 5 R40 R/RX41 R/RX41 R/RX41 R/RX41 R/RX44 R42 6 R43 R/RX45 R/RX45 R/RX45 R/RX45 R/RX46 R/RX47 8 R48 R/RX49 R/RX49 R/RX49 R/RX49 R/RX50 R51 10 R52 R/RX53 R/RX53 R/RX53 R/RX53 R/RX54 R55 12 R56 R/RX57 R/RX57 R/RX57 R/RX57 R58 R60 14 R59 R61 R61 R61 R62 R/RX63-16 R64 R/RX65 R/RX65 R/RX65 R/RX66 R67-18 R68 R/RX69 R/RX69 R/RX69 R/RX70 R71-20 R72 R/RX73 R/RX73 R/RX73 R/RX74 R75-24 R76 R77 R77 R77 R78 R79-23

24 Ring Joint Gaskets RX Series RX series are interchangeable with R series octagonal gaskets designed for API 6B flanges. RX out perform R series in situations that have higher pressures with more intense vibrations. RX gaskets are available up to 5,000 PSI. RX Model R and RX (For flanges in accordance with API spec 6A, model 6B) Ring Number at Class Rating Pipe Size /6 R/RX23 R/RX24 R/RX24 2-9/16 R/RX26 R/RX27 R/RX27 3-1/8 R/RX31 R/RX31 R/RX35 4-1/16 R/RX37 R/RX37 R/RX39 5-1/8 R/RX41 R/RX41 R/RX44 7-1/16 R/RX45 R/RX45 R/RX46 9 R/RX49 R/RX49 R/RX50 11 R/RX53 R/RX53 R/RX /8 R/RX57 R/RX /4 R/RX65 R/RX /4 - R/RX /4 R/RX Model R or RX (For flanges in accordance with ASME B16.47 series A (MSS-SP44)) Ring Number at Class Rating Pipe Size R93 R R94 R R95 R R96 R R97 R R98 R105 24

25 Ring Joint Gaskets BX Series BX series ring joint gaskets feature a pressure relief vent and are designed for API 6BX flanges reaching pressures up to 20,000 PSI. BX Model BX Ring Number at Pressure Rating (PSI) Pipe Size / BX150 BX / BX151 BX151 BX / BX152 BX152 BX / BX153 BX153 BX / BX154 BX154 BX / BX155 BX155 BX / BX169 BX / BX156 BX156 BX BX157 BX157 BX BX158 BX158 BX /8 - - BX160 BX159 BX159 BX /4 - - BX162 BX /4 - - BX163 BX164 BX /4 - - BX165 BX /4 BX167 BX BX303 BX

26 Ring Joint Gaskets Polyurethane Test Gaskets Product Description: Hi-Tech Seals manufactures polyurethane ring joint gaskets for application testing. The polyurethane ring joint gaskets are an effective and non-damaging method for testing gland the before use. The uniquely shaped profile energizes the seal in the groove under pressure, replicating a stainless steel R or BX ring joint gasket. Hi-Tech Seals polyurethane test gaskets last up to 100 test runs at 15,000 PSI. Rubber Coated Test Gaskets Rubber coated ring joint test gaskets are used to test flanges before service. The rubber coating avoids potentially damaging metal-to-metal contact. Rubber coated test gaskets are an economical option over the polyurethane test gaskets. With proper handling, rubber coated test gaskets can be used in several tests. 26

27 Spiral Wound Gaskets Winding Materials: Max. Temp. Range Stainless Steel C Stainless Steel 316L 760 C Filler Materials: Graphite 523 C PTFE 260 C Guide Ring Materials: Carbon Steel 538 C Inner Ring Materials: Stainless Steel C Stainless Steel C Winding Winding w/ Inner Ring Winding w/ Centering Ring Winding w/ Inner & Centering Ring Product Description: Spiral wound gaskets are designed for ASME B16.20 and ANSI B16.5 flanges. Spiral wound gaskets are available for classes 150 to Custom filler, winding strip, guide ring and inner ring materials are available upon request. Part Numbers: SWG - Nom. Pipe Size Class Rating Winding Material Internal Ring Material* Centering Ring Material* Filler Material Example: SWG G C I - spiral wound gasket - 26 nominal pipe, 150#, stainless steel 316 winding material, graphite filler, carbon steel centering ring, stainless steel 316 inner ring * If there is no internal ring or if there is no centering ring then the respective materials will not be listed. 27

28 Spiral Wound Gaskets Selecting Your Spiral Wound Gasket Applications Service: Raised Face Flat Face Male & Female Tongue & Groove Flat Face to Recessed General Duty Winding w/ Centering Ring Winding w/ Centering Ring Winding Winding Winding High Pressure High Temperature Fluctuating Pressures SWG w/ PTFE Fillers Winding w/ Inner & Centering Ring Winding w/ Inner & Centering Ring Winding w/ Inner Ring Winding w/ Inner Ring Winding w/ Inner Ring Colour Coding Centering rings are painted in accordance to ASME B The solid colour on the centering ring indicates the metallic winding material. The stripped colour indicates the non-metallic filler used between the metal winding. PTFE Ceramic Flexible Graphite Phyllosilicate Non-Metallic Filler 304 SS 316L SS 317L SS 347 SS 321 SS Monel Inconel Nickel Incoloy Titanium Alloy 20 Carbon Steel Hastelloy B Hastelloy C Phos. Bronze Winding Material 28

29 Spiral Wound Gaskets Winding Pipes Under 24 Sealing Element O.D. Sealing Element I.D. ASME B16.5 & BS 1560 Flanges Nom. Pipe Size Sealing Element Male and Female Large Tongue Groove Small Tongue and Groove Sealing Element Class 2500 Sealing Element Class Sealing Element I.D. O.D. I.D. O.D. I.D. O.D. I.D. O.D. 1/4 1/ / / /8 13/16 1-3/ / /8 3/4 1-5/ /16 1-1/ /16 1-5/ /16 1-5/ / / / / /2 1-7/8 1-1/4 1-7/8 2-1/2 1-5/8 2-1/2 1-7/8 2-1/2 1-7/8 2-1/4 1-1/2 2-1/8 2-7/8 1-7/8 2-7/8 2-1/8 2-7/8 2-1/8 2-1/ /8 3-5/8 2-3/8 3-5/8 2-7/8 3-5/8 2-7/8 3-1/4 2-1/2 3-3/8 4-1/ /8 3-3/8 4-1/8 3-3/8 3-3/ / / / /4 4-5/8 3-1/2 4-3/4 5-1/ /4 5-1/2 4-3/4 5-1/ /16 6-3/16 4-3/4 6-3/16 5-3/16 6-3/16 5-3/ /16 4-1/2 5-11/16 6-3/ /16 6-3/ /16 7-5/16 5-3/4 7-5/16 6-5/16 7-5/16 6-5/ / /2 8-1/2 6-3/4 8-1/2 7-1/2 8-1/2 7-1/ /8 10-5/8 8-3/4 10-5/8 9-3/8 10-5/8 9-3/ /4 12-3/4 10-3/4 12-3/4 11-1/4 12-3/4 11-1/ / / /2 14-1/ /4 16-1/ /4 16-1/4 14-3/4 15-1/ / /2 16-3/4 17-5/ / / /4 20-1/ /4 27-1/ /4 27-1/4 25-1/4 26-1/4 Small Tongue and Groove Flanges: Classes 300 thru 2500 are interchangeable within their specific size category 3/4 size are interchangeable with Large Male & Female and Large Tongue and Groove gaskets within their specific pressure rating 1/2 size are interchangeable within Large Male & Female and Large Tongue and Groove gaskets within their specific pressure rating Male & Female and Large Tongue & Groove Flanges: Class 300, 400, 600 gaskets are interchangeable within their size category Class 900 and 1500 gaskets are interchangeable within their size category 1/4 size in 150 class are interchangeable 29

30 Spiral Wound Gaskets Winding With Centering Ring Pipes Under 24 Centering Ring O.D. Sealing Element O.D. Sealing Element I.D. ASME B16.20 for ASME B16.5 Flanges Nom. Inside Diameter of Sealing Element Outside Diameter of Sealing Element Outer Diameter of Centering Ring Pipe Size , , , /4 1/2 1/2 1/2 1/ /8-1-3/4 1-3/4 1-3/4 1-3/ /2 3/4 3/4 3/4 3/4 3/4 3/4 3/4 1-1/4 1-1/4 1-7/8 2-1/8 2-1/8 2-1/8 2-1/2 2-1/2 2-3/4 3/ /16 1-9/16 2-1/4 2-5/8 2-5/8 2-5/8 2-3/4 2-3/ /4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-7/8 1-7/8 2-5/8 2-7/8 2-7/8 2-7/8 3-1/8 3-1/8 3-3/8 1-1/4 1-7/8 1-7/8 1-7/8 1-7/8 1-9/16 1-9/16 1-9/16 2-3/8 2-3/ /4 3-1/4 3-1/4 3-1/2 3-1/2 4-1/8 1-1/2 2-1/8 2-1/8 2-1/8 2-1/8 1-7/8 1-7/8 1-7/8 2-3/4 2-3/4 3-3/8 3-3/4 3-3/4 3-3/4 3-7/8 3-7/8 4-5/ /4 2-3/4 2-3/4 2-3/4 2-5/16 2-5/16 2-5/16 3-3/8 3-3/8 4-1/8 4-3/8 4-3/8 4-3/8 5-5/8 5-5/8 5-3/4 2-1/2 3-1/4 3-1/4 3-1/4 3-1/4 2-3/4 2-3/4 2-3/4 3-7/8 3-7/8 4-7/8 5-1/8 5-1/8 5-1/8 6-1/2 6-1/2 6-5/ /4 3-5/8 3-5/8 4-3/4 4-3/4 5-3/8 5-7/8 5-7/8 5-7/8 6-5/8 6-7/8 7-3/4 3-1/2 4-1/2 4-1/2 4-1/8 4-1/8 4-1/8 4-1/8-5-1/4 5-1/4 6-3/8 6-1/2 6-3/8 6-3/8 7-1/2 7-3/ /4 4-3/4 4-3/4 4-5/8 4-5/8 5-7/8 5-7/8 6-7/8 7-1/ /8 8-1/8 8-1/4 9-1/4 4-1/2 5-1/2 5-1/2 5-5/16 5-5/16 5-5/16 5-5/16-6-1/2 6-1/ /4 7-5/8 8-1/4 9-3/8 9-1/ /8 6-1/8 5-13/ / /16 5-5/8 5-5/ /4 8-1/2 8-3/8 9-1/2 9-3/ /16 7-3/16 6-7/8 6-7/8 6-7/8 6-3/4 6-3/4 8-1/4 8-1/4 8-3/4 9-7/8 9-3/4 10-1/2 11-3/8 11-1/8 12-1/ /16 9-3/16 8-7/8 8-7/8 8-3/4 8-1/2 8-1/2 10-3/8 10-1/ / /8 14-1/8 13-7/8 15-1/ / / / / /8 10-1/2 10-5/8 12-1/2 12-1/4 13-3/8 14-1/4 14-1/8 15-3/4 17-1/8 17-1/8 18-3/ /8 13-3/8 12-7/8 12-7/8 12-3/4 12-3/4 12-1/2 14-3/4 14-1/2 16-1/8 16-5/8 16-1/ /8 20-1/2 21-5/ /8 14-5/8 14-1/4 14-1/ / /4 17-3/4 19-1/ /8 20-1/2 22-3/ /8 16-5/8 16-1/4 16-1/4 16-1/ / /4 21-1/4 21-1/8 22-1/4 22-5/8 25-1/ / / /2 18-1/2 18-1/4 18-1/4-20-3/4 20-1/2 21-5/8 23-1/2 23-3/8 24-1/8 25-1/8 27-3/ / / /2 20-1/2 20-1/2 20-1/4-22-3/4 22-1/2 23-7/8 25-3/4 25-1/2 26-7/8 27-1/2 29-3/ /4 24-3/4 24-3/4 24-3/4 24-3/4 24-1/ /4 28-1/4 30-1/2 30-1/4 31-1/ /2-30

31 Spiral Wound Gaskets Inner Ring Dimensions Pipes Under 24 Centering Ring O.D. Sealing Element O.D. Sealing Element I.D. Inner Ring I.D. Standard Inside Diameter of Inner Rings Nom. Pipe Size Pressure Class / / / / /

32 Spiral Wound Gaskets Series B Flanges 26 and Over Nom. Pipe Size Class 75 Class 150 Class 300 Sealing Element Centering Inner Sealing Element Centering Inner Sealing Element I.D. O.D. Ring O.D. Ring I.D. I.D. O.D. Ring O.D. Ring I.D. I.D. O.D. Centering Ring O.D / /8 25-3/4 26-1/2 27-1/2 28-9/ /4 26-1/ / /4 29-1/8 29-7/8 27-3/4 28-1/2 29-1/2 30-9/ /4 28-1/ / /4 31-1/8 31-7/8 29-3/4 30-1/2 31-1/2 32-9/ /4 30-1/ / /4 33-1/8 33-7/8 31-3/4 32-1/2 33-1/ / /4 32-1/ /4 35-1/8 35-7/8 33-3/4 34-1/2 35-3/ / /4 34-1/ / /4 37-1/4 38-5/ /4 36-1/2 37-3/4 38-7/8 35-3/4 36-1/ / /4 38-3/8 39-3/4 41-1/8 38-1/4 39-3/4 41-1/4 43-1/ /4 40-1/4 41-7/8 43-1/8 40-1/4 41-3/4 43-1/4 45-1/ /4 43-1/4 44-5/ /4 42-1/2 43-7/8 45-1/8 42-3/4 43-3/4 45-1/4 47-1/ /4 44-1/4 45-7/8 47-1/8 44-1/4 45-3/4 47-1/4 49-1/ /4 46-1/2 48-3/ / /8 47-7/8 49-3/8 51-7/ /8 49-1/2 50-1/2 47-3/4 48-1/ / /2 49-3/4 51-5/8 53-7/ /4 50-1/2 52-3/ / /8 51-7/8 53-3/8 55-7/ /4 52-1/2 54-3/ / /8 53-7/8 55-3/8 57-7/ /8 55-5/8 56-5/8 53-3/4 54-1/ /8 53-3/4 55-1/4 57-1/4 60-1/ /8 58-3/ /8 56-1/4 58-1/ / / / / / / / / / /2 61-3/4 62-7/8 60-7/ / / / / / / /16 Nom. Pipe Size Inner Ring I.D. Class 400 Class 600 Class 900 Sealing Element Centering Inner Sealing Element Centering Inner Sealing Element I.D. O.D. Ring O.D. Ring I.D. I.D. O.D. Ring O.D. Ring I.D. I.D. O.D /4 26-1/4 27-1/2 29-3/8 25-3/8 26-1/8 28-1/8 30-1/8 26-1/4 27-1/4 29-1/2 33 Centering Ring O.D /8 28-1/8 29-1/2 31-1/ /4 29-3/4 32-1/4 28-1/4 29-1/4 31-1/2 35-1/ /8 30-1/8 31-3/4 33-3/4 29-5/8 30-5/8 32-5/8 34-5/8 30-3/4 31-3/4 33-3/4 37-3/ / /8 35-7/8 31-1/4 32-3/4 34-3/4 36-3/ /2 34-1/8 35-7/8 37-7/8 33-1/ /4 35-1/4 36-1/4 38-1/4 42-1/ /8 36-1/ /4 35-1/ /4 36-1/4 37-1/4 39-1/4 44-1/ /2 38-1/4 40-1/4 42-1/4 37-1/ /2 39-3/4 40-3/4 42-3/4 47-1/ /8 40-3/8 42-3/8 44-3/8 39-3/4 41-1/4 43-1/4 45-1/2 41-3/4 43-1/4 45-1/4 49-1/ /8 42-3/8 44-3/8 46-3/ /2 45-1/ /4 45-1/4 47-1/4 51-1/ /2 44-1/2 46-1/2 48-1/2 43-3/4 45-3/4 47-3/ /2 47-1/2 49-1/2 53-7/ /4 45-3/4 47-3/4 49-3/4 52-1/ / / / / / / / / /4 55-1/4 57-1/4 59-3/8 54-1/4 56-1/4 58-1/4 61-1/ /4 57-1/4 59-1/4 61-3/4 56-1/4 58-1/4 60-1/4 63-1/ /4 59-3/4 61-1/4 63-3/ /2 62-1/2 65-1/ /4 61-3/4 63-3/4 66-1/4 60-1/4 62-3/4 64-3/4 68-1/

33 Spiral Wound Gaskets Series A Flanges 22 and Over Nom. Pipe Size Inner Ring I.D. Class 150 Class 300 Class 400 Sealing Element Centering Inner Sealing Element Centering Inner Sealing Element I.D. O.D. Ring O.D. Ring I.D. I.D. O.D. Ring O.D. Ring I.D. I.D. O.D. Centering Ring O.D / /4 24-3/4 27-3/4-22-3/4 24-3/4 27-5/ /4 26-1/2 27-3/4 30-1/2 25-3/ / / /4 28-1/2 29-3/4 32-3/4 27-3/ / / /4 30-1/2 31-3/4 34-3/4 29-3/4 31-1/4 33-1/4 37-1/2 29-3/4 31-1/4 33-1/4 37-1/ /4 32-1/2 33-7/ /4 33-1/2 35-1/2 39-5/ /2 35-1/2 39-1/ /4 34-1/2 35-7/ /4 35-1/2 37-1/2 41-5/ /2 37-1/2 41-1/ /4 36-1/2 38-1/8 41-1/4 35-3/4 37-5/8 39-5/ /8 37-5/8 39-5/ /4 38-1/2 40-1/8 43-3/4 37-1/2 38-1/ /2 37-1/2 38-1/4 40-1/4 42-1/ /4 40-1/2 42-1/8 45-3/4 39-1/2 40-1/4 42-1/8 43-7/8 39-3/8 40-3/8 42-3/8 44-3/ /4 42-1/2 44-1/ /2 42-1/4 44-1/8 45-7/8 41-3/8 42-3/8 44-3/8 46-3/ /4 44-1/2 46-3/8 50-1/4 43-1/2 44-1/2 46-1/ /2 44-1/2 46-1/2 48-1/ /4 46-1/2 48-3/8 52-1/4 45-3/8 46-3/8 48-3/8 50-1/ / /4 48-1/2 50-3/8 54-1/2 47-5/8 48-5/8 50-5/8 52-1/8 47-1/ /4 50-1/2 52-1/2 56-1/ /4 49-1/ / /4 52-1/2 54-1/2 58-3/ /4 51-1/ / /2 54-1/2 56-1/ /4 55-1/4 57-1/4 58-3/4 53-1/4 55-1/4 57-1/4 59-3/ /2 56-1/2 58-1/2 63-1/4 55-1/4 57-1/4 59-1/4 60-3/4 55-1/4 57-1/4 59-1/4 61-3/ /2 58-1/2 60-1/2 65-1/ /2 61-1/2 62-3/4 57-1/4 59-1/4 61-1/4 63-3/ /2 60-1/2 62-1/2 67-1/ /2 63-1/2 64-3/4 59-3/4 61-3/4 63-3/4 66-1/4 Nom. Pipe Size Inner Ring I.D. Class 600 Class 900 Sealing Element Centering Inner Ring Sealing Element I.D. O.D. Ring O.D. I.D. I.D. O.D. Centering Ring O.D /4 24-3/4 28-7/ / / / / / /4 31-1/4 33-1/4 38-1/4 30-1/4 31-1/4 33-1/4 39-3/ /2 35-1/2 40-1/ /2 35-1/2 42-1/ /2 37-1/2 42-1/ /2 37-1/2 44-3/ /8 37-5/8 39-5/8 44-1/2 36-1/4 37-3/4 39-3/4 47-1/ / /2 39-3/4 40-3/4 42-3/4 47-1/ /4 41-1/4 43-1/4 45-1/2 41-3/4 43-1/4 45-1/4 49-1/ /2 45-1/ /4 45-1/4 47-1/2 51-1/ /4 45-3/4 47-3/ /2 47-1/2 49-1/2 53-7/ /4 47-3/4 49-3/4 52-1/ / / / /4 56-1/4 58-1/4 61 1/ /4 58-1/4 60-1/4 63-1/ /2 62-1/2 65-1/ /4 62-3/4 64-3/4 68-1/

34 Kammprofile Metal Core Material* Temperature Stainless Steel 304 Up to 760 C Stainless Steel 316 Up to 760 C Sealing Material Flexible Graphite Up to 510 C PTFE Up to 260 C * Additional materials available upon request. No Guide Ring Integral Guide Ring Loose Fit Guide Ring Product Description: The Kammprofile (camprofile) is designed with a metal core featuring a serrated surface. Flexible graphite or PTFE is bonded to the serrated surface which forms the sealing element. The serrated surface prevents movement of the seal within the flange, while the malleable sealing element conforms to deformations. The Kammprofile features excellent compressibility and recovery characteristics. For more information on Kammprofiles visit. Profile for Flange Flange Type Male / Female Tongue / Groove Flat Face Full Face No Guide Ring Integral Guide Ring Loose Fit Guide Ring 34

35 Isolation Kits Materials Temperature G10 Up to 140 C Viton Fluorocarbon -59 C to 204 C Nitrile -51 C to 116 C PTFE -73 C to 450 C Minlon - C to C Raised Face Trojan Gasket Full Face Trojan Gasket Washer Sleeve-Washer Sleeve Product Description: Isolation kits provide near zero leakage while protecting your flange against corrosion caused by the transfer of electricity. Isolation gaskets are manufactured in accordance to ANSI B16.5 specifications for sizes up to 24. Kits are available with a Trojan high performance gasket, isolating sleeves, washers or sleeve-washer one piece units. Part Numbers: APS - K Pipe Size Class # Kit Gasket Type: E - Raised Face F - Full Face Gasket Style: TRO - Trojan N - Nitrile/Phenolic * - other Gasket Sealing Element: V - Viton T - PTFE Washer: SW - Single Set DW - Double Set SI - Single One-Piece DI - Double One-Piece Example: APS F TRO V SW K - Trojan Isolation Kit - 10,000 nom. pipe size, class 900#, full face gasket, Trojan w/ a Viton sealing element, single washer set and sleeves. 35

36 Studs & Nuts Stud Materials Application A193, Grade B7 Chromium-Molybdenum Sweet A193, Grade B7M Chromium-Molybdenum Sour Nut Materials: A194, Grade 2H Carbon and Alloy Steel Sweet A194, Grade 2HM Carbon and Alloy Steel Sour Studs Heavy Hex Nuts Product Description: Hi-Tech Gaskets offers finished studs and heavy hex nuts in diameters ranging from 1/2 to 3. The B7 grade stud and the 2H grade nut are designed for sweet gas applications; whereas, the B7M grade stud and the 2HM grade nut are designed for sour gas applications. Standard stocked studs and nuts threads comply with UN thread shape and dimensions. Part Numbers: STU - Diameter Threads Per Inch Length Material NUT - Diameter Material Threads Per Inch Example: STU B7M - stud, 3/4 diameter, 10 threads per Inch, 3-1/4 in length, B7M material Example: NUT HM - nut, 3/4 inner diameter, 10 threads per Inch, 2HM material 36

37 Studs & Nuts Studs Length Diameter Part Number Diameter Threads Per Inch Length STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / Part Number Diameter Threads Per Inch Length STU / /4 STU / /2 STU / /4 STU / STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU /8 9 3 STU / /4 STU / /2 STU / /4 STU /8 9 4 STU / /4 STU / /2 STU / /4 STU /8 9 5 STU / /4 STU / /2 STU / /4 STU /

38 Studs & Nuts Studs Part Number Diameter Threads Per Inch Length STU / /4 STU / /2 STU / /4 STU /8 9 7 STU / /4 STU / /2 STU / /4 STU /8 9 8 STU / /4 STU / /2 STU / /4 STU /8 9 9 STU / /4 STU / /2 STU / /4 STU / STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 Part Number Diameter Threads Per Inch Length STU STU /8 8 3 STU / /4 STU / /2 STU / /4 STU /8 8 4 STU / /4 STU / /2 STU / /4 STU /8 8 5 STU / /4 STU / /2 STU / /4 STU /8 8 6 STU / /4 STU / /2 STU / /4 STU /8 8 7 STU / /4 STU / /2 STU / /4 STU /8 8 8 STU / /4 STU / /2 STU / /4 STU /8 8 9 STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU /4 8 3 STU / /4 STU / /2 STU / /4 STU /4 8 4 STU / /4 STU / /2 STU / /4 STU /4 8 5 STU / /4 STU / /2 STU / /4 STU /4 8 6 STU / /4 38

39 Studs & Nuts Studs Part Number Diameter Threads Per Inch Length STU / /2 STU / /4 STU /4 8 7 STU / /4 STU / /2 STU / /4 STU /4 8 8 STU / /4 STU / /2 STU / /4 STU /4 8 9 STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU /8 8 5 STU / /4 STU / /2 STU / /4 STU /8 8 6 STU / /4 STU / /2 STU / /4 STU /8 8 7 STU / /4 STU / /2 STU / /4 STU /8 8 8 STU / /4 STU / /2 STU / /4 STU /8 8 9 STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / Part Number Diameter Threads Per Inch Length STU /2 8 5 STU / /4 STU / /2 STU / /4 STU /2 8 6 STU / /4 STU / /2 STU / /4 STU /2 8 7 STU / /4 STU / /2 STU / /4 STU /2 8 8 STU / /4 STU / /2 STU / /4 STU /2 8 9 STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU /8 8 5 STU / /4 STU / /2 STU / /4 STU /8 8 6 STU / /4 STU / /2 STU / /4 STU /8 8 7 STU / /4 STU / /2 STU / /4 STU /8 8 8 STU / /4 STU / /2 STU / /4 STU /8 8 9 STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 39

40 Studs & Nuts Studs Part Number Diameter Threads Per Inch Length STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU /4 8 5 STU / /4 STU / /2 STU / /4 STU /4 8 6 STU / /4 STU / /2 STU / /4 STU /4 8 7 STU / /4 STU / /2 STU / /4 STU /4 8 8 STU / /4 STU / /2 STU / /4 STU /4 8 9 STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU /8 8 5 STU / /4 STU / /2 STU / /4 STU /8 8 6 STU / /4 STU / /2 STU / /4 STU /8 8 7 STU / /4 STU / /2 STU / /4 STU /8 8 8 STU / /4 STU / /2 Part Number Diameter Threads Per Inch Length STU / /4 STU /8 8 9 STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU / /4 STU / /2 STU / /4 STU / STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU STU /4 STU /2 STU /4 STU

41 Studs & Nuts Heavy Hex Nuts Part Number Thread Diameter Threads per Inch NUT /2 13 NUT /8 11 NUT /4 10 NUT /8 9 NUT NUT /8 8 NUT /4 8 NUT /8 8 NUT /2 8 NUT /8 8 NUT /4 8 NUT /8 8 NUT

42 Bolt Protectors Materials Temperature Low Density Polyethylene -70 C to 80 C Locking Cap (SW) Wedge Cap (KSW) Telescopic Cap (TSW) Bolt Cap (BM) Bolt Thread Cap (B) Product Description: Bolt protectors insulate the threading and/or nut from its surrounding environment. The specially formulated low-density polyethylene compound contains volatile corrosion inhibitors (VCI). The VCIs slowly release from the elastomer in the form of vapour, which provides improved corrosion resistance. Protection of the nut and threading will allow for easier dismantlement of the flange for general maintenance. Caps are reusable and will last up to several years. Part Numbers: CAP - Height 1 Height 2 Width Profile Type 42

43 Thread Protectors Material: Temperature Low Density Polyethylene -70 C to 80 C High Density Polyethylene -70 C to 80 C Caps & Plugs (CP) Bolted Flange Protector (BFP) Stud-hole Flange Protector (FC) Stud-hole Flange Protector (FC) Valve-Flange Protector (FP) Product Description: Protector products are excellent for preventing damage to equipment during storage or transport. Additional protector products are available upon request. To view a complete sizing list, visit us online at 43

44 Braided Packing Material information is available on the next page. For assistance selecting the correct braided packing, please contact a Hi-Tech Gaskets' representative. Braided Packing Braided Packing Extractors Product Description: Braided packing is a rope like material which is cut into rings that wrap around the rod. Once installed the compression force generated by tightening of the gland produces radial pressure. Since braided packing expands radially when compressed, the gland tolerances can be more flexible than when using vee packing. Hi-Tech Gaskets distributes braided packing based on weight, measured in pounds. However, Arochem, Kombilon, Univerdit, Carbosteam and Ramilon are distributed in kilograms units. If you would like the estimated feet/pound of specific materials please contact Hi-Tech Gaskets. Braided packing is available in imperial and metric sizes. Part Numbers: PKG - C/S Material Weight: Blank - 1 pound 5LB - 5 pounds 10LB - 10 pounds Example: PKG G 10LB - 10 pound package of material 3000G braided packing - 3/8 C/S 44

45 Braided Packing Material Max. Temp. 300 Description: Aramide filament is impregnated with PTFE and an inert lubricant. 260 C Pump and valve packing, suitable for slurry and abrasive service. 320 Description: Kynol impregnated with PTFE suspensoid. 260 C Pumps and valves. Not suitable for sulfuric acid or strong bases. 344 Description: PTFE fibre impregnated with PTFE suspensoid. 260 C Valve service with extreme chemicals. 344BIL Description: Pure PTFE fibre impregnated with PTFE suspensoid and an inert break in lubricant. 260 C Pump service with extreme chemicals. Not suitable with molten alkalis. 344FDA Description: FDA grade PTFE filament impregnated with PTFE suspensoid. 260 C Valve service with extreme chemicals requiring FDA grade packing. 345 Description: Flax and ramie fibres impregnated with PTFE suspensoid and an inert lubricant. 90 C Marine applications. 895 Description: Uncoated soft annealed copper wire. 540 C Acts as an anti-extrusion ring. 921 Description: Flax and ramie fibres are impregnated with tallow and wax lubricants. 90 C Cold water, brine and marine services. 921G Description: Flax and ramie fibres are impregnated with tallow and the surface is lubricated with graphite. 90 C Heavy duty hydraulic packing used in marine applications involving oil or cold water. 3000G Description: An special acrylic yarn blend impregnated with high temperature lubricant and finished with particulate graphite. Economical, general purpose pump and valve service. 3000T Description: A special acrylic yarn blend impregnated with PTFE suspensoid. An inert lubricant is added for ease of start up. General pump and valve service. 3000TK Description: A special acrylic yarn blend impregnated with PTFE suspensoid. An inert lubricant is added for ease of start up. This braided packing material also has aramide corners. High speed pumps where non-contaminating packing is desired. 3030INA Description: High temperature non-asbestos valve stem and expansion joint packing for moderate services. 650 C Used when experiencing high temperature steam, gases and hydrocarbons Description: Non-staining carbon yarn is impregnated with PTFE. 290 C Non-staining general service pump and valve packing. 4000G Description: Carbon yarn impregnated with a blocking agent and lubricated with high temperature graphite. 400 C General service pump and valve packing for use with solvents, petrochemicals, mild acids and alkalis Description: Pure expanded flexible graphite C Flexible packing providing low friction, excellent heat transfer and chemical resistance. 5000C Description: Pure expanded flexible graphite with corners of carbon yarn C Flexible packing providing extrusion resistance, low friction, excellent heat transfer and chemical resistance. 5000I Description: High density, Inconel reinforced, flexible graphite with collodial graphite coating. 800 C Extreme service valve packing. Meets API 589/607 fire test standards. 230 C 260 C 260 C 45

46 Braided Packing Material Max. Temp. 5000IFE Description: Inconel reinforced expanded graphite and coated with collodial graphite. 315 C Valve service, certified to Fugitive Emissions Standards API 589/ T Description: Flexible graphite yarn impregnated with PTFE and inert lube. 90 C Excellent for valve and pump service. Provides good chemical resistance and heat dissipation properties. 8000LC Description: Industrial grade graphite filament treated with a special graphite coating to eliminate fraying C High shaft speed pump and valve applications. Suitable for extreme heat and aggressive chemicals. 8000G Description: Pure graphite yarn with a blocking agent and graphite lubricant. 650 C High shaft speed pump and valve applications. Suitable for extreme heat and aggressive chemicals. 8000T Description: GFO fibre yarn. 290 C Suitable for acids, alkalis, solvents and steam. 8000TK Description: GFO fibre yarn braided with aramide corners. 260 C Pump packing which provides abrasion and extrusion resistance Description: Anti-friction lead foil is twisted over a soft fibreglass core. High temperature oil and graphite lubricant is added. Boiler feed pumps or used as an end ring in conjunction with other packing where extrusion exists Description: Anti-friction aluminum foil is twisted over a fibreglass core. High temperature oil and graphite lubricant is added. For use in boiler feed pumps, in abrasive solutions and as an anti-extrusion ring Description: Anti-friction lead foil. High temperature oil and graphite lubricant is added. 230 C Boiler feed pumps or used as an end ring in conjunction with other packing where extrusion exists Description: Anti-friction aluminum foil. High temperature oil and graphite lubricant is added. 540 C For use in boiler feed pumps, in abrasive solutions and for use as an anti-extrusion ring. 8100BIL Description: A dense but soft lubricated PTFE/graphite braided packing. 275 C Pump packing which provides anti-extrusion properties. 8200BIL Description: A dense PTFE/graphite braided packing. 275 C Economical multi-purpose packing. Arochem Description: Arochem (6212) is aramide yarn with PTFE. 280 C Plunger pumps. Provides strong chemical resistance. Kombilon Description: Kombilon(6742) is a carbon and PTFE yarn. 280 C Ideal for rotary pumps. Works well in agitators for the paper and chemical industries. Univerdit Description: Univerdit (7000) is a PTFE/graphite compound. 250 C Pump and valve packing. Provides good resistance to gas permeation. Carbosteam Description: Carbosteam (6550) is made of flexible carbon yarns impregnated with graphite. 399 C Suitable for high temperature, high pressure and it is extrusion resistant. Ramilon Description: Ramilon (4586) is PTFE impregnated fibres. 120 C Economical water pump packing. 230 C 540 C 46

47 Joint Sealant Materials Temperature PTFE, Expanded -268 C to 316 C Product Description: Joint sealant is composed of 100% virgin expanded PTFE. Expanded PTFE provides near universal resistance and good compressibility. The joint sealant rope has an adhesive peelable tape on one side, allowing for easy installation. Joint sealant is suitable for FDA applications. Hi-Tech Gaskets distributes joint sealant by the spool. Spool length varies based on the cross-section. C/S Feet/Spool Flange Size 1/8 100, /2 to 3/4 3/16 100, to 1-1/2 1/4 50, 100, to 3-1/2 3/8 25, 50, to 6 1/2 15, 30, to 16 5/8 15, 30, to 20 3/4 15, 30, 50, to , 30, to to up Part Numbers: PKG - TJS C/S Feet Example: PKG - TJS PTFE joint sealant - 1/4 cross-section, 50 foot spool Example: PKG - TJS PTFE joint sealant - 1/4 cross-section, 500 foot spool 47

48 Redline Gauge Glass Redline Gauge Glass Cleaning Brushes Product Description: Redline gauge glass is typically used in low pressure boilers, reservoirs and tank applications. The redline gauge glass features a red stripe and a white stripe. In the presence of a colourless fluid the red and white line magnifies and highlights the fluid level. Pressure ratings vary depending on diameter, thickness and environment. Part Numbers: SGP - X O.D. Length REDLINE - Gauge Glass BRUSH - Cleaning Brush Example: SGP - 12 X 18 REDLINE - redline gauge glass - 1/2" O.D., 18" in length 48

49 Manufacturing O.D. Length N/R - Not Recommended Max. Recommended Working Pressure (PSI) Part Number O.D. Wall Thickness Length Temp. Up to 66 C Temp. Up to 218 C No Corrosion Steam Boiler Service SGP 12X8REDLINE SGP 12X10REDLINE SGP 12X12REDLINE SGP 12X14REDLINE SGP 12X18REDLINE SGP 12X20REDLINE 1/2 5/ SGP 12X24REDLINE +0, -1/32 +/- 1/ SGP 12X30REDLINE N/R SGP 12X36REDLINE N/R SGP 12X48REDLINE N/R SGP 12X60REDLINE N/R SGP 12X72REDLINE N/R SGP 58X8REDLINE SGP 58X10REDLINE SGP 58X12REDLINE SGP 58X14REDLINE SGP 58X16REDLINE SGP 58X18REDLINE /8 3/32 SGP 58X20REDLINE , -1/32 +/- 1/64 SGP 58X24REDLINE SGP 58X30REDLINE N/R SGP 58X36REDLINE N/R SGP 58X48REDLINE N/R SGP 58X60REDLINE N/R SGP 58X72REDLINE N/R SGP 34X8REDLINE SGP 34X10REDLINE SGP 34X12REDLINE SGP 34X14REDLINE SGP 34X16REDLINE SGP 34X18REDLINE SGP 34X20REDLINE 3/4 7/ SGP 34X22REDLINE +0, -1/32 +/- 1/ SGP 34X24REDLINE SGP 34X30REDLINE N/R SGP 34X36REDLINE N/R SGP 34X48REDLINE N/R SGP 34X60REDLINE N/R SGP 34X72REDLINE N/R SGP 78X30REDLINE N/R 7/8 1/8 SGP 78X48REDLINE N/R +0, -1/32 +/- 1/32 SGP 78X72REDLINE N/R SGP 1X24REDLINE N/R 1 1/8 SGP 1X30REDLINE N/R +0, -1/32 +/- 1/32 SGP 1X36REDLINE N/R 49

50 Additional Products Mud Plug Kits Mud plug kits are an all-in-one package used in field or plant shut downs during hot tie-ins. The mud mixture prevents the migration of lazy gas in the pipelines. Once service is complete, the mud can be washed away cleanly and safely Kit Contents: MSDS & Instructions Pail 16 lb of Bentonite 2 x 3.78 litres of washer fluid Mask Gloves Mixing stick Rags Screw Packing Four primary styles: Homogeneous highly saturated nitrile Individual graphoil rings Stacked graphoil rings with tops and bottoms preformed from graphoil rope packing Bonded stack of graphoil rings with tops and bottoms made of stainless steel 316 Fibre Glass Rope Fibre glass rope offers strong characteristics such as resistance to heat and abrasion, while insulating from electricity. Fibre glass rope is available in diameters 1/4 to 2. Applications: pipe wrap, boiler, furnace, oven, gas fireplace, wood/gas/tile stoves, thermal insulation, glass manufacturing, flange gasketing and fireproof safe applications. 50

51 Additional Products Boiler Gaskets Hi-Tech Gasket supplies specialty boiler gaskets in Blue-Max and Black-Max styles. Boiler gaskets are manufactured in oval, obround, rectangular, round, and square shapes. Blue-Max Blue-Max gaskets were developed as a substitute for asbestos gaskets. They are composed of a tacky cloth of glass, synthetic fibres, and brass wire, impregnated with a blue elastomer compound. The product is then coated in a PTFE material. Black-Max The Black-Max gasket is composed of graphite with multiple layers of stainless steel 316 foil inserts. The gasket is fit for service in -240 C to 454 C in oxidizing atmospheres and 650 C in steam service. Pipe Roller Polyurethane is an ideal material for wear and bearing surfaces. Hi-Tech Seals urethane division manufactures custom pipe rollers. PTFE Tape PTFE tape is an ultra-thin material typically used to seal pipe threads. The material provides near universal chemical resistance. 51

52 Additional Products Tank Stripping The neoprene strip material is used to seal between bolted panels on tanks. The strip comes with half inch bolt holes spaced two inches apart from bolt centre. The material is 1-3/4 wide by 75 feet, available in various thicknesses. The most common thickness is 1/8. Chime Lap Gaskets Available in Nitrile and EPDM. Fillet Strip Fillet, also known as Radii gaskets, are sold in strips or cut to length. Gaskets are available in Nitrile and EPDM. 52

53 Service Field Service One of our trained team members will visit the site of tanks, vessels, or facilities to measure and identity components. Service charges are a $65.00/hour measuring fee and a $0.60 / KM millage fee. Once the gaskets are identified our team can manufacture replacement parts and store the information gathered for future use. After Hours Hi-Tech Gaskets has a sales representative available 24 hours a day, 7 days a week to serve you. You can reach our after-hours service by dialing Our after-hours charges are $ per call in, provided we can service you. After-hours machining charges are $ per call in, and an additional $ per hour of labour, with a minimum of one hour labour charge. Hi-Tech Gaskets reserves the right to change pricing without notice. Our regular service hours are 8:00 am to 5:00 pm, Monday-Friday. Gasket Kits Gasket kits can increase the ease of reordering. Hi-Tech Gaskets can prepackage and stock your gaskets, nuts, studs, lubricant, and more! Kits can include your part number, application description, and even your assemble instructions. 53

54 Manufacturing Hi-Tech Seals About Hi-Tech Seals Hi-Tech Gaskets is a subsidiary of Hi-Tech Seals. Hi-Tech Seals was founded in Edmonton, Alberta on October 1st, Hi-Tech Seals has a longstanding commitment to customer service. Our technical sales team works side-by-side with customers to find the best solution for any problem. Customers count on our ability to source quality products at affordable prices and stock them ready for delivery. Hi-Tech Seals has expanded our service geographically, as well as, through the expansion of our manufacturing capabilities. Specialists in Seals & Service ISO 9001 REGISTERED QMS Locations: Hi-Tech Seals has stocking and service facilities located at: Ave. NW T6E 6R5 Ph: Fax: Bay #3, St. SE Calgary, AB T2C 1X8 Ph: Fax: Egesz St. Winnipeg, MB R2R 2V5 Ph: Fax: Kerrisdale Blvd; Unit #8 Newmarket, ON L3Y 8Z9 Ph: Fax: Rue Nobel, Suite #20 Boucherville, QC J4B 5H3 Ph: Fax: Gladstell Street Conroe, TX United States Ph: Fax: Hi-Tech Gaskets main stocking and service location is located at Ave NW, T6E 5K8. Service and supply of gaskets is available through any Hi-Tech Seals location. 54

55 Hi-Tech Seals Plastic & Rubber Machining Rubber & Plastic Machining Since 1999, Hi-Tech Seals has offered in-house rubber & plastic machining services. Machining facilities are located in and Winnipeg, MB. Customers can select from one of our pre-programmed seal profiles, or create a custom seal by providing a sample or drawing. With the help of our experienced machining, sales, drafting and engineering staff, we can quickly design and manufacture new prototype parts in a matter of hours without expensive tooling charges. Capabilities Hi-Tech Seals has several CNC lathes, multiple NC machines, milling and live tooling capabilities at our disposal. Hi-Tech Seals is capable of creating custom parts with profiles ranging from ¼ (6mm) inside diameter and up to as large as 29 (737mm) outside diameter. Materials Hi-Tech Seals stocks rod and tubes of plastic and elastomer materials for production and direct for sale. Plastics: Nylon Acetal Hytrel UHMW PEEK (Virgin, Carbon Filled, & Glass Filled) PTFE Virgin Bronze Filled Carbon Filled Carbon / Graphite Filled Glass Filled Moly / Glass Filled Elastomers: Nitrile Highly Saturated Nitrile Ethylene Propylene Fluorocarbon Aflas Neoprene Polyurethane Profiles Our Computer Aided Manufacturing (CAM) software has over 120 pre-programmed seal profiles. Our team can help you select the correct profile or design a custom sealing component. Hi-Tech Seals offers an in-house drafting service to provide quick turn around. To learn more about Hi-Tech Seals manufacturing process, request a copy of our Rapid Seal brochure or visit us online at 55

56 Manufacturing Hi-Tech Seals Cast Urethane Hi-Tech Seals cast urethane division is centrally located in Winnipeg, Manitoba. Cast urethane parts are utilized as a replacement for previously used plastic, rubber or metal components. This versatile material can allow for lighter, quieter and longer lasting products. Polyurethane s excellent physical characteristics can save you money by increasing wear resistance, providing less downtime and by having less product breakage. Mold Making Our cast urethane division utilizes a 3D printer to create scale models of components. The process allows us to have full control of our mold development and it allow us to reduce expensive tooling charges. 56

57 Hi-Tech Seals Customizing Your Urethane Types of Urethane When creating a customized urethane product we can select from two main types of Polyurethane. The two main types of Polyurethane are Polyethers and Polyesters. Polyesters: Oil and fuel resistance Wear resistance Dynamic properties Polyethers: More flexibility over polyesters Better hydrolysis resistance Durometer We can maintain the urethanes toughness and resilience while producing a polyurethane as soft as 30 Shore A to as hard as 87 D. Shore A Shore D Custom Colours Black, red, yellow, orange, green, blue, white or custom corporate colours. Logo & Part Numbers Hi-Tech Seals can mold your logo and part numbers into your components. Molded identification marks will help you create brand awareness and identify proprietary parts. 57

58 Manufacturing Hi-Tech Seals Full Access Hi-Tech Gasket customers have access to a complete line of components offered by our sister company, Hi-Tech Seals. Hi-Tech Seals has an extensive line of sealing, wear, protector and vibration control components. Products O-Rings O-rings are available in Nitrile, low temperature Nitrile, Highly Saturated Nitrile, Genuine Viton fluorocarbon, PTFE, Aflas, Neoprene, EPDM, Perfluoroelastomer, Silicone and Fluorosilicone. Hydraulic / Pneumatic Seals View our full range of piston and rod seals for hydraulic and pneumatic cylinders in our Seal Catalogue or online at Wear Rings Wear rings are used to keep a piston centered, which allows for even wear and pressure. Common materials include: nylon, filled PTFEs and PEEK. 58

59 Hi-Tech Seals Carbide Tungsten carbide components offer extreme temperature, wear and chemical resistance. All carbide components are custom designed for our clientèle. Ceramics Ceramic components offer excellent thermal stability and wear resistance in corrosive, abrasive and erosive environments. Ceramic is ideal for bearings, bushings, and in valves, pumps and mechanical applications. Protectors Protector products are designed to protect application from impact during storage or transport. Available styles include: friction fit caps & plugs, threaded protectors, flange protectors, sleeve mesh and more. Oilfield Specific For over twenty years, Hi-Tech Seals has been working with customers from exploration to production to produce quality oilfield components. Custom Molding Our team works closely with to connect customers with globally sourced solutions. We source quality parts at affordable prices, and stock them ready for delivery. 59