TECHNICAL MANUAL UNIT, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS

Transcription

1 TECHNICAL MANUAL UNIT, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS TAMPER, BACKFILL: GASOLINE ENGINE DRIVEN, HAND-OPERATED, RAM-TYPE MODEL VR11C (NSN ) MODEL VR11 (NSN ) This manual supersedes, dated 14 June 1985; and, this manual and TM supersede TM &P, dated 30 January 1981, and all changes. Approved for public release; distribution is unlimited. HEADQUARTERS, DEPARTMENT OF THE ARMY 20 APRIL 1993

2 TECHNICAL MANUAL * HEADQUARTERS DEPARTMENT OF THE ARMY Washington D.C, 20 April 1993 UNIT, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS TAMPER, BACKFILL: GASOLINE ENGINE DRIVEN, HAND-OPERATED, RAM-TYPE MODEL VR11C (NSN ) MODEL VR11 (NSN ) Current as of 22 January 1993 REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form , located in the back of this manual, direct to: Commander, U.S. Army Tank-Automotive Command, ATTN: AMSTA-MB, Warren, MI A reply will be furnished to you. Approved for public release; distribution is unlimited. TABLE OF CONTENTS Page SECTION I. INTRODUCTION REPAIR PARTS LIST Illus Fig GROUP 01 GROUP 03 ENGINE ENGINE ASSEMBLY ENGINE ASSEMBLY CRANKCASE, BLOCK, CYLINDER HEAD CRANKCASE, BLOCK, CYLINDER HEAD CRANKSHAFT CRANKSHAFT PISTONS AND CONNECTING RODS PISTONS AND CONNECTING RODS ENGINE STARTING SYSTEMS ENGINE STARTING SYSTEM FUEL SYSTEM CARBURETOR, FUEL INJECTOR CARBURETOR *This manual supersedes, dated 14 June 1985; and, this manual and TM supersede TM &P, dated 30 January 1981, and all changes. Approved for public release; distribution is unlimited.

3 TABLE OF CONTENTS (Con t) Illus Page Fig AIR CLEANER AIR CLEANER (VR11C) AIR CLEANER (VR11) TANKS, LINES, FITTINGS, HEADERS TANKS, LINES, FITTINGS ACCELERATOR, THROTTLE, OR CHOKE CONTROLS THROTTLE CONTROL (VR11C) THROTTLE CONTROL (VR11) GROUP 04 EXHAUST SYSTEM MUFFLER AND PIPES MUFFLER GROUP 06 ELECTRICAL SYSTEM IGNITION COMPONENTS IGNITION COMPONENTS GROUP 07 TRANSMISSION TRANSMISSION ASSEMBLY TRANSMISSION ASSEMBLY TRANSMISSION CLUTCH AND CLUTCH CONTROLS TRANSMISSION CLUTCH AND CLUTCH CONTROLS REDUCTION OR TRANSFER GEARS, SHAFTS, AND BEARINGS 16-1 TRANSFER GEARS, SHAFTS, AND BEARINGS GROUP 15 FRAME. TOWING ATTACHMENTS, DRAWBARS, AND ARTICULATION SYSTEMS FRAME ASSEMBLY FRAME ASSEMBLY (VR11C) FRAME ASSEMBLY (VR11) GROUP 22 BODY, CHASSIS, AND HULL ACCESSORY ITEMS ACCESSORY ITEMS ACCESSORY ITEMS (VR11C) DATA PLATES AND INSTRUCTION HOLDERS DATA PLATE AND DECALS GROUP 74 CRANES, SHOVELS, AND EARTHMOVING EQUIPMENT COMPONENTS DRIVE MECHANISM LOWER UNIT DRIVE MECHANISM (VR11C) LOWER UNIT DRIVE MECHANISM (VR11) SHOE DRIVE MECHANISM GROUP 94 REPAIR KITS REPAIR KITS... KITS-1 REPAIR KITS... KITS-1 ii

4 TABLE OF CONTENTS (Con t) Page Illus Fig GROUP 95 GENERAL USE STANDARDIZED PARTS BULK MATERIEL... BULK-1 BULK MATERIEL... BULK-1 I. GROUP 26 SPECIAL TOOLS TOOLS AND TEST EQUIPMENT SPECIAL TOOLS SPECIAL TOOLS SECTION IV. CROSS-REFERENCE INDEXES NATIONAL STOCK NUMBER INDEX... I-1 PART NUMBER INDEX... I-4 FIGURE AND ITEM NUMBER INDEX... I-10 iii(iv Blank)

5 UNIT, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS SECTION I. INTRODUCTION 1. Scope. This RPSTL lists and authorizes spares and repair parts; special tools; special test, measurement, and diagnostic equipment (TMDE); and other special support equipment required for performance of Unit, Direct Support, and General Support Maintenance of the Back fill Tamper. It authorizes the requisitioning, issue, and disposition of spares, repair parts and special tools as indicated by the source, maintenance and recoverability (SMR) codes. 2. General. In addition to Section I. Introduction, this Repair Parts and, Special Tools List is divided into the following sections: a. Section II. Repair Parts List. A list of spares and repair parts authorized by this RPSTL for use in the performance of maintenance. The list also includes parts which must be removed for replacement of the authorized parts. Parts lists are composed of functional groups In ascending alphanumeric sequence, with the parts in each group listed in ascending figure and item number sequence. Bulk materials are listed In item name sequence. Repair kits are listed separately in their own functional group within Section II. Repair parts for reparable special tools are also Listed in the section. Items listed are shown on the associated illustration(s)/figure(s). b. Section III. Special Tools List. A list of special tools, special TMDE, and other special support equipment authorized by this RPSTL (as indicated by Basis of Issue (BOI) information in DESCRIPTION AND USABLE ON CODE column) for the performance of maintenance. c. Section IV Cross-reference Indexes. A list, in National Item Identification Number (NIIN) sequence, of all National stock numbered items appearing in the listing, followed by a list in alphanumeric sequence of all part numbers appearing in the listings. National stock numbers and part numbers are cross-referenced to each illustration/figure and item number appearance. The figure and item number index lists figure and item numbers in alphanumeric sequence and crossreferences NSN, CAGE, and part numbers. 3. Explanation of Columns (Sections II and III). a. ITEM NO. (Column (1)). Indicates the number used to identify items called out in the illustration. b. SMR CODE (Column (2)). The Source, Maintenance, and Recoverability (SMR) code is a 5position code containing supply/requisitioning information, maintenance category authorization criteria, and disposition instructions, as shown in the following breakout: 1st two positions 3d position Source Code XXxxx How you get an item. Maintenance Code xxxxx 4th position Who can install, replace Who can do complete or use the item repair* on the item. Recoverability Code xxxxx 5th position Who determine disposition action on an unserviceable item. *Complete Repair: Maintenance capacity, capability, and authority to perform all corrective maintenance tasks of the "Repair" function in a use/user environment in order to restore serviceability to a failed item. (1) Source Code. The source code tells you how to get an item needed for maintenance, repair, or overhaul of an end item/equipment. Explanations of source codes follows: 1

6 Code PA PB PC** PD PE PF PG KD KF KB Application/Explanation Stocked items; use the applicable NSN to request/requisition items with these source codes. They are authorized to the category indicated by the code entered in the 3d position of the SMR code. ** Items coded PC are subject to deterioration. Items with these codes are not to be requested/requisitioned individually. They are part of a kit which is authorized to the maintenance category indicated in the 3d position of the SMR code. The complete kit must be requisitioned and applied. MO-(Made at UMI/ AVUM Level) MF-(Made at DSI AVUM Level) MH-(Made at GS Level) ML-(Made at Specialized Repair Activity (SRA)) MD-(Made at Depot) AO-(Assembled by UM/ AVUM Level) AF-(Assembled by DS/AVIM Level) AH-(Assembled by GS Category) AL-(Assembled by SRA) AD-(Assembled by Depot) XA - XB - Items with these codes are not to be requested/requisitioned individually. They must be made from bulk material which is identified by the part number in the DESCRIPTION AND USABLE ON CODE (UOC) column and listed in the Bulk Material group of the repair parts list in this RPSTL. If the item is authorized to you by the 3d position code of the SMR code, but the source code indicates it is made at a higher level, order the item from the higher level of maintenance. Items with these codes are not to be requested/requisitioned items with these codes are not to be requested/requisitioned individually. The parts that make up the assembled item must be requisitioned or fabricated and assembled at the level of maintenance indicted by the source code. If the 3d position code of the SMR code authorizes you to replace the item, but the source code indicates the item is assembled at a higher level, order the item from the higher level of maintenance. Do not requisition an "XA"-coded item. Order its next higher assembly. (Also refer to the NOTE following.) If an "XB" item is not available from salvage, order it using the CAGE and part number given. XC - XD - Installation drawing, diagram, instruction sheet, field service drawing, that is identified by the manufacturer s part number. Item is not stocked. Order an "XD"-coded item through normal supply channels using the CAGE and part number given, if no NSN is available. NOTE: Cannibalization or controlled exchange, when authorized, may be used as a source of supply for items with the above source codes, except for those source coded "XA" or those aircraft support items restricted by requirements of AR (2) Maintenance Code. Maintenance codes tell you the level(s) of maintenance authorized to USE and REPAIR support items. The maintenance codes are entered in the third and fourth positions of the SMR code as follows: (a) The maintenance code entered in the third position tells you the lowest maintenance level authorized to remove, replace, and use an item. The maintenance code entered in the third position will indicate authorization to one of the following levels of maintenance. Code C - Application/Explanation Crew or operator maintenance done within unit maintenance or aviation unit maintenance. O - Unit maintenance or aviation unit category can remove, replace, and use the item. F - Direct support or aviation intermediate level can remove, replace, and use the item. H - General support level can remove, replace, and use the item. L - Specialized repair activity can remove, replace, and use the item. D - Depot level can remove, replace, and use the item. (b) The maintenance code entered in the fourth position tells whether or not the item is to be repaired and identifies the lowest maintenance level with the capability to do complete repair (i.e., perform all authorized repair functions). (NOTE: Some limited repair may be done on the item at a lower level of maintenance, if authorized by the Maintenance Allocation Chart (MAC) and SMR codes.) This position will contain one of the following maintenance codes: Code O - F - Application/Explanation Unit maintenance or aviation unit is the lowest level that can do complete repair of the item Direct support or aviation intermediate is the lowest level than can do complete repair of the item. 2

7 H - L - D - Z - B - General support is the lowest level that can do complete repair of the item. Specialized repair activity is the lowest level that can do complete repair of the item. Depot is the lowest level that can do complete repair of the item. Non reparable. No repair is authorized. No repair is authorized. (No parts or special tools are authorized for the maintenance of a "B"-coded item.) However, the item may be reconditioned by adjusting, lubricating, etc., at the user level. (3) Recoverability Code. Recoverability codes are assigned to items to indicate the disposition action on unserviceable items. The recoverability code is entered in the fifth position of the SMR code as follows: Code Application/Explanation Z- Non reparable item. When unserviceable, condemn and dispose of the item at the level of maintenance shown in the 3d position of the SMR code. O- Reparable item. When uneconomically reparable, condemn and dispose of the item at unit maintenance or aviation unit level. F- Reparable item. When uneconomically reparable, condemn and dispose of the item at the direct support or aviation intermediate level. H- Reparable item. When uneconomically reparable, condemn and dispose of the item at the general support level. D- Reparable item. When beyond lower level repair capability, return to depot. Condemnation and disposal of item not authorized below depot level. L- Reparable item. Condemnation and disposal of item not authorized below specialized repair activity (SRA). A - Item requires special handling or condemnation procedures because of specific reasons (e.g., precious metal content, high dollar value, critical material, or hazardous material). Refer to appropriate manuals/directives for specific instructions. c. CAGEC (Column (3)). The Commercial and Government Entity (CAGE) Code (C) is a 5-digit alphanumeric code which is used to identify the manufacturer, distributor, or Government agency, etc., that supplies the item. d. PART NUMBER (Column (4)). Indicates the primary number used by the manufacturer (individual, company, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications standards, and inspection requirements to identify an item or range of items. NOTE: When you use an NSN to requisition an item, the item you receive may have a different part number from the part ordered. e. DESCRIPTION AND USABLE ON CODE (UOC) (Column (5)). This column includes the following information: (1) The Federal item name and, when required, a minimum description to identify the item. (2) Physical security classification. Not Applicable. (3) Items that are included in kits and sets are listed below the name of the kit or set on Figure KIT. (4) Spare/repair parts that make up an assembled item are listed immediately following the assembled item line entry. (5) Part numbers for bulk materials are referenced in this column in the line item entry for the item to be manufactured/fabricated. (6) When the item is not used with all serial numbers of the same model, the effective serial numbers are shown on the last line(s) of the description (before UOC). (7) The usable on code, when applicable (see paragraph 5, Special Information). (8) In the Special Tools List section, the basis of issue (BOI) appears as the last line(s) in the entry for each special tool, special TMDE, and other special support equipment. When density of equipment supported exceeds density spread indicated in the basis of issue, the total authorization is increased proportionately. (9) The statement "END OF FIGURE" appears just below the last item description in Column 5 for a given figure in both Section II and Section III. f. QTY (Column (6)). The QTY (quantity per figure column) indicates the quantity of the item used in the breakout shown on the illustration/figure, which is prepared for a functional group, sub functional group, or an assembly. A "V" appearing in this column in lieu of a quantity indicates that the quantity is variable and the quantity may vary from application to application. 4. Explanation of Columns (Section IV). a. NATIONAL STOCK NUMBER (NSN) INDEX. (1) STOCK NUMBER column. This column lists the NSN by National Item Identification Number (NIIN) 3

8 sequence. The NIIN consists of the last nine NSN digits of the NSN (i.e., ).When NIIN using this column to locate an item, ignore the first 4 digits of the NSN. However, the complete NSN should be used when ordering items by stock number. (2) FIG. column. This column lists the number of the figure where the item is identified/located. The figures are in numerical order in Section II and Section III. (3) ITEM column. The item number identifies the item associated with the figure listed in the adjacent FIG. column. This item is also identified by the NSN listed on the same line. b. PART NUMBER INDEX. Part numbers in this index are listed by part number in ascending alphanumeric sequence (i.e., vertical arrangement of letter and number combination which places the first letter or digit of each group in order A through Z, followed by the numbers 0 through 9 and each following letter or digit in like order). (1) CAGEC column. The Commercial and Government Entity (CAGE) Code (C) is a 5-digit alphanumeric code used to identify the manufacturer, distributor, or Government agency, etc., that supplies the item. (2) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications standards, and inspection requirements to identify an item or range of items. (3) STOCK NUMBER column. This column lists the NSN for the associated part number and manufacturer identified in the PART NUMBER and CAGE columns to the left. (4) FIG. column. This column lists the number of the figure where the item is identified/located in Sections II and III. (5) ITEM column. The Item number is that number assigned to the item as it appears in the figure referenced in the adjacent figure number column. c. FIGURE AND ITEM NUMBER INDEX. (1) FIG. column. This column lists the number of the figure where the item is identified/located in Sections II and Ill. (2) ITEM column. The item number is that number assigned to the item as it appears in the figure referenced in the adjacent figure number column. (3) STOCK NUMBER column. This column lists the NSN for the item. (4) CAGEC column. The Commercial and Government Entity (CAGE) Code (C) is a 5-digit alphanumeric code used to identify the manufacturer, distributor, or Government agency, etc., that supplies the item. (5) PART NUMBER column. Indicates the primary number used by the manufacturer (individual, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications standards and inspection requirements to identify an item or range of items. 5. Special Information. a. USABLE ON CODE. The usable on code appears in the lower left corner of the Description column heading. Usable on codes are shown as "UOC: in the Description column (justified left) on the first line following applicable item description/nomenclature. Uncoded items are applicable to all models. Identification of the usable on codes used in the RPSTL are: Code Used On T77 VR11 VRC VR11C b. FABRICATION INSTRUCTIONS. Bulk materials required to manufacture items are listed in the Bulk Material Functional Group of this RPSTL. Part numbers for bulk materials are also referenced in the Description column of the line item entry for the item to be manufactured/fabricated. Detailed fabrication instructions for items source coded to be manufactured or fabricated are found in TM c. ASSEMBLY INSTRUCTIONS. Detailed assembly instructions for items source coded to be assembled from component spare/repair parts are found in TM Items that make up the assembly are listed immediately following the assembly item entry or reference is made to an applicable figure. d. KITS. Line item entries for repair parts kits appear in group 9401 in Section II. e. INDEX NUMBERS. Items which have the word BULK in the figure column will have an index number shown in the item number column. This index number is a cross-reference between the National Stock Number/Part Number Index and the bulk material list in Section II. f. ASSOCIATED PUBLICATIONS. The publications listed below pertain to the Back fill Tamper and its components: Publication TM Short Title Backfill Tamper, VR11 and VR11C 4

9 6. How to Locate Repair Parts. a. When National Stock Number or Part Number is Not Known: (1) First. Using the table of contents, determine the assembly group or subassembly group to which the item belongs. This is necessary since figures are prepared for assembly groups and subassembly groups, and listings are divided into the same groups. (2) Second. Find the figure covering the assembly group or subassembly group to which the item belongs. (3) Third. Identify the item on the figure and use the Figure and Item Number Index to find the NSN. b. When National Stock Number or Part Number is Known: (1) First. Using the National Stock Number or Part Number Index, find the pertinent National Stock Number or Part Number. The NSN index is in National Item Identification Number (NIIN) sequence (see paragraph 4.a.(1)). The part numbers in the Part Number index are listed in ascending alphanumeric sequence (see paragraph 4.b). Both indexes crossreference you to the illustration/figure and item number of the item you are looking for. (2) Second. Turn to the figure and item number, verify that the item is the one you re looking for, then locate the item number in the repair parts list for the figure. 7. Abbreviations. For standard abbreviations see MIL-STD-12D, Military Standard Abbreviations for Use on Drawings, Specifications, Standards, and in Technical Documents. Abbreviations Explanation NIIN...National Item Identification Number (consist of the last 9 digits of the NSN) RPSTL... Repair Parts and Special Tools List 5

10 FIGURE 1. ENGINE ASSEMBLY.

11 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 01 ENGINE GROUP 0100 ENGINE ASSEMBLY FIG. 1 ENGINE ASSEMBLY 1 PAFZZ GASKET PAFZZ MS BOLT1MACHINE PFFZZ ADAPTER, ENGINE PAFZZ GASKET PBFFF ENGINE GASOLINE MODEL PAFZZ MS SCREW, CAPIHEXAGON H PAFZZ MS WASHER LOCK PAFZZ M WASHER LOCK PAFZZ MS SCREW CAP, HEXAGON H XDFZZ BRACKETIENGINE... 2 END OF FIGURE 1-1

12 FIGURE 2. CRANKCASE, BLOCK, CYLINDER HEAD.

13 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 0101 CRANKCASE, BLOCK CYLINDER HEAD FIG. 2 CRANK CASE BLOCLK CYLINDER HEAD 1 PFFZZ A CYLINDER,ENGINE1GAS PFFZZ SEAL PAFZZ SCREW;MACHINE KFFZZ GASKET, BEARING CAGE PART OF KIT P/N PFFZZ A SUPPORT; CRANKSHAFT PFFZZ BEARING;TROLLER ;NEED PFFZZ STUD; PLAIN PFFZZ SEAL PAFZZ SCREW, ASSEMBLED WAS KFFZZ GASKET, REED PLATE PART OF KIT P/N PFFZZ A PLATE ASSEMBLY; REED PFFZZ SCREW; ASSEMBLED WAS PFFZZ STOP, REED ENG.EXHAU PFFZZ REED, ENGINE EXHAUST PFFZZ STUD PAFZZ NUT; PLAIN;HEXAGON PAFZZ SCREW, ASSEMBLED WAS... 4 END OF FIGURE 2-1

14 FIGURE 3. CRANKSHAFT.

15 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 0102 CRANKSHAFT FIG. 3 CRANKSHAFT 1 PFFZZ A CRANKSHAFT; ENGINE PFFZZ RING;RETAINING PFFZZ BEARING; BALL;ANNULA PFFZZ RING; RETAINING... 1 END OF FIGURE 3-1

16 FIGURE 4. PISTONS AND CONNECTING RODS.

17 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 0104 PISTONS AND CONNECTING RODS FIG. 4 PISTONS AND CONNECTING RODS 1 PFFZZ RING;RETAINING PFFZZ PIN, PISTON PFFZZ A RING SET;PISTON PFFZZ PISTON, INTERNAL COM PFFZZ A ROLLER AND CAGE SET, PFFZZ A CONNECTING ROD;PIST PFFZZ SCREW; CAP SOCKET;HE... 2 END OF FIGURE 4-1

18 FIGURE 5. ENGINE STARTING SYSTEM.

19 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 0107 ENGINE STARTING SYSTEM FIG. 5 ENGINE STARTING SYSTEM 1 PFOZZ K PARTS KIT, HAND ENGI CVRSN KIT... 1 STARTER... 2 PFOZZ CUP, STARTER PAOZZ WASHERILOCK PBOOO STARTER;ENGINE, HAND PFOZZ SCREEN, ENGINE START PFOZZ SCREW, DOG RETAINER PFOZZ RETAINER;DOG PFOZZ SPRINGIHELICAL, COMP PFOZZ DOG, SET, STARTER PFOZZ SPRING PFOZZ A HANDLE, STARTER, ROPE PFOZZ PULLY, STARTER XDOZZ SPRING, SPIRAL TORSI PFOZZ COVER, HAND STARTER PFOZZ ROPE PAOZZ MS NUT;PLAIN, HEXAGON PAOZZ SCREW;ASSEMBLED WAS... 4 END OF FIGURE 5-1

20 FIGURE 6. CARBURETOR.

21 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 03 FUEL SYSTEM GROUP 0301 CARBURETOR, FUEL INJECTOR CARBURETOR, FUEL INJECTOR FIG. 6 CARBURETOR 1 PBOZZ K CARBURETOR;FLOAT PFFZZ CHOKE SHAFT AND LEV PFFZZ BUSHING, SLEEVE; CHOKE PAFZZ CLIP, SPRING TENSION PAFZZ WASHER, LOCK PAFZZ SCREW, MACHINE PFFZZ VALVEICHOKE PAFZZ SCREW;ASSEMBLED WAS PFFZZ BALL, CHOKE FRICTION XOFZZ BALL, CHOKE FRICTION PFFZZ SPRING, TORSION, KFFZZ GASKET, INLET SEAT PART OF KIT P/N... 1 K KFFZZ NEEDLE;INLET PART OF KIT P/N K KFFZZ SPRING, INL TENSION PART OF KIT P/N... 1 K10117 T KFFZZ LEVER, INLET CONTROL PART OF KIT P/N... 1 K XDFZZ LEVER, INLET CONTROL KFFZZ PLUG, BOOY CHANNEL PART OF KIT P/N... 1 K KFFZZ PLUG; WELCH PART OF KIT P/N K KFFZZ SPRING, ADJUST SCREW PART OF KIT P/N... 2 K10101T PFFZZ WASHER, FLAT KFFZZ SCREW, MN ADJUSTMENT PART OF KIT P/N... 1 K KFFZZ WASHER, ADJUST SCREW PART OF KIT P/N... 2 K10009 PART OF KIT P/N K10117OI.,. 21 KFFZZ PACKING, ADJ SCREW PART OF KIT P/N... 2 K10009 PART OF KIT P/N K PFFZZ IDLE ADJUSTOR SCRE W PFFZZ SPRING, EXTENSION PFFZZ SHAFT, LEVER;THROTTL PFFZZ PIN, STRAIGHT, HEADLE XDFZZ PIN;STRAIGHT;HEADLE PFFZZ SCREW;MACHINE XDFZZ SCREW;MACHINE

22 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY 27 PAOZZ GASKET, CARBURETOR KFFZZ SCREW ASSEM WASHER PART OF KIT P/N... 1 K PFFZZ SHUTTER;THROTTLE KFFZZ SCREW, REGULATING PART OF KIT P/N... 1 K KFFZZ SPRING, RGLT SCREW PART OF KIT P/N... 1 K PFFZZ WASHER, FLAT KFFZZ SCREW PART OF KIT P/N K PAFZZ COVER, STRAINER KFFZZ GASKET, COVER PART OF KIT P/N K KFFZZ STRAINER, FUEL PART OF KIT P/N PAFZZ SCREW;MACHINE XDFZZ SCREW;MACHINE PFFZZ BODY, PUMP, CARBURETO KFFZZ DIAPHRAGM, FUEL PUMP PART OF KIT P/N... 1 K , PFFZZ DIAPHRAGM, FUEL PUMP KFFZZ GASKET;FUEL PUMP PART OF KIT P/N... 1 K PFFZZ COVER; DIAPHRAGM KFFZZ DIAPHRAGM PART OF KIT P/N K KFFZZ GASKET, DIAPHRAGM PART OF KIT P/N... 1 K10009, PFOZZ A ARM ASSEMBLY, THROTT PFOZZ NUT;SELF LOCK CAP PFOZZ SCREW, ASSEMBLED WAS... 1 END OF FIGURE 6-2

23 FIGURE 7. AIR CLEANER (VR11C).

24 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 0304 AIR CLEANER FIG. 7 AIR CLEANER (VR11C) 1 PAOZZ MS NUT, PLAIN, WING PFOZZ COVER1ACCESS PAOZZ AFP79 FILTER ELEMENT;INTA PAOZZ MS WASHER, LOCK... 2 UOC: VRC 5 PAOZZ MS SCREW, CAP, SOCKET HE PFOZZ HOSE;PREFORMED PFOZZ CLAMP;HOSE PAOZZ ELBOW;FLANGE PFOZZ GASKET... 1 END OF FIGURE 7-1

25 1 2 THRU 5 FIGURE 8. AIR CLEANER (VR11).

26 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 0304 AIR CLEANER FIG. 8 AIR CLEANER (VR11) 1 PAOZZ CAA-2W/ FILTER, COMPLETE XDOZZ AIR FILTER HOUSING PAOZZ FILTER PIN... 1 UOC: T77 4 XDOZZ FILTER COVER PAOZZ FILTER ELEMENT... 1 END OF FIGURE 8-1

27 FIGURE 9. TANKS, LINES, FITTINGS.

28 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 0306 TANKS, LINES, FITTINGS, HEADERS FIG. 9 TANKS LINES FITTINGS 1 PFOZZ BUMPER, NONMETALLIC PFOZZ BUMPER, NONMETALLIC PFOFF TANK, FUEL, ENGINE XDOZZ T S CLAMP;LOOP PFOZZ CAP, VENTIFUEL STORA PFOZZ CLAMPIHOSE MOOZZ XX HOSE, FUEL MAKE FROM HOSE P/N XDOZZ A FILTER;FLUID PFOZZ CLAMP, HOSE PFOZZ CAP, FILLER OPENING... 1 END OF FIGURE 9-1

29 FIGURE 10. THROTTLE CONTROL (VR11C).

30 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 0312 ACCELERATOR THROTTLE, OR CHOKE CONTROLS FIG. 10 THROTTLE CONTROL (VR11C) 1 PAOZZ MT CLIP,SPRING TENSION PAOZZ MS WASHER, LOCK PFOZZ S CLIP, THROTTLE PFOZZ CONTROL ASSEMBLY, PU PAOZZ MS PIN,COTTER PAOZZ MS NUT, PLAIN, HEXAGON PAOZZ MS WASHER,LOCK... 2 END OF FIGURE 10-1

31 FIGURE 11. THROTTLE CONTROL (VR11) TA705269

32 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 0312 ACCELERATOR, THROTTLE, OR CHOKE CONTROLS FIG. 11 THROTTLE CONTROL (VR11) 1 PAOZZ THROTTLE ASSEMBLY PAOZZ MT CLAMP XDOZZ THROTTLE BRACKET... 1 END OF FIGURE 11-1

33 FIGURE 12. MUFFLER

34 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 04 EXHAUST SYSTEM GROUP 0401 MUFFLER AND PIPES FIG. 12 MUFFLER 1 PAOZZ MS SCREW, CAP, HEXAGON H PAOZZ MS WASHER, LOCK PFOZZ N MUFFLER, EXHAUST KFOZZ GASKET, MUFFLER PART OF KIT P/N END OF FIGURE 12-1

35 FIGURE 13. IGNITION COMPONENTS

36 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 06 ELECTRICAL SYSTEM GROUP 0605 IGNITION COMPONENTS FIG. 13 IGNITION COMPONENTS 1 PFOZZ A HOUSING, ENGINE FAN PFOZZ GROMMET, NONMETALLIC PFOZZ CONNECTOR UNIT PFOZZ LEAD, ELECTRICAL PBOFF PLATE, STATOR KFOZZ SCREW, ASSEM WASHER PAOZZ CAPACITOR, FIXED, PAP PAOZZ CONTACT SET, DISTRIB PFOZZ WIPER, CAM KFFZZ SPRING, WEDGE, COIL KFFFF K12368 COIL ASSEMBLY KFOZZ K750-2 TERMINAL KFOZZ SPRING, BREAKER COV PAFZZ PLATE, STATOR XDOZZ SCREW, BREAKER CLAMP PAOZZ UJ-11G SPARK PLUG PFOZZ CLAMP, LOOP PFFZZ CAM, MAGNETIC PAFZZ SCREW, ASSEMBLED WAS PFOZZ GASKET PFOZZ COVER, BREAKER PFOZZ FLYWHEEL, ENGINE PAOZZ KEY PAOZZ NUT,SELF LOCKING PAOZZ WASHER, LOCK, PFOZZ WASHER1FLAT PFOZZ SWITCH, PUSH... 1 END OF FIGURE 13-1

37 FIGURE 14. TRANSMISSION ASSEMBLY

38 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 07 TRANSMISSION GROUP 0700 TRANSMISSION ASSEMBLY FIG. 14 TRANSMISSION ASSEMBLY 1 AFFFF GEARCASE ASSEMBLY PFFZZ MS PIN, STRAIGHT, HEADLE PFFZZ COVER ASSEMBLYBEAR PFFZZ COVER, GEARCASE PFFZZ RS BEARING, BALL, ANNULA PAFZZ X1E9 BEARING, BALL, ANNULA PFOZZ BRACKET, ANGLE PAOZZ ZA0 SCREW, TAPPING PFFZZ GASKET PFFZZ SPEED COVER, TAMPER PAFZZ ZA0 SCREW, TAPPING PFFZZ GEARCASE PFFZZ GASKET PFFZZ Z00 SCREW, TAPPING END OF FIGURE 14-1

39 FIGURE 15. TRANSMISSION CLUTCH AND CLUTCH CONTROLS

40 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 0703 TRANSMISSION CLUTCH AND CLUTCH CONTROLS FIG. 15 TRANSMISSION CLUTCH AND CLUTCH CONTROLS 1 PAFZZ SHAFT, CLUTCH ASSEMB PAFZZ MS RING, RETAINING, EXT PFFZZ GEAR, SPUR, PINION PAFZZ MS KEY, WOODRUFF PFFZZ SHAFT, CLUTCH PFFZZ RS BEARING, BALL, ANNULA PAFZZ MS21044N7 NUT, SELF-LOCKING, HE PFFZZ SPACER, SLEEVE... 1 UOC: VRC 9 PFFZZ R CLUTCH, POSITIVE PAFZZ MS KEY, WOODRUFF PFFZZ SPACER, SLEEVE... 1 END OF FIGURE 15-1

41 FIGURE 16. TRANSFER GEARS, SHAFTS, AND BEARINGS

42 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 0719 REDUCTION OR TRANSFER GEARS, SHAFTS, AND BEARINGS FIG. 16 TRANSFER GEARS, SHAFTS? AND BEARINGS 1 AFFFF SHAFT ASSEM, INTMD PAFZZ MS RING, RETAINING PFFZZ GEAR, SPUR PAFZZ MS KEY, WOODRUFF PFFZZ SHAFT, SHOULDERED PAFZZ GEAR, SPUR, PINION PAFZZ MS RING, RETAINING PFFZZ RS BEARING, BALL, ANNULA PFFFF CRANKSHAFT, ENGINE PFFZZ BUSHING, SLEEVE... 1 END OF FIGURE 16-1

43 FIGURE 17. FRAME ASSEMBLY (VR11C)

44 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 15 FRAME, TOWING ATTACHMENTS, DRAWBARS, AND ARTICULATION SYSTEMS GROUP 1501 FRAME ASSEMBLY FIG. 17 FRAME ASSEMBLY (VR11C) 1 PFOZZ HANDLE-WELD ASSEMBL PAOZZ MS WASHER, LOCK PAOZZ MS BOLT, MACHINE PFOZZ GUARD, CARBURETOR PFOZZ MOUNT, RESILIENT PAOZZ MS90728 SCREW, CAP, HEXAGON H PAOZZ MS WASHER, LOCK PAOZZ MS WASHER, FLAT... 6 END OF FIGURE 17-1

45 FIGURE 18. FRAME ASSEMBLY (VR11)

46 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 1501 FRAME ASSEMBLY FIG. 18 FRAME ASSEMBLY (VR11) 1 XDOZZ HANDLE PAOZZ STRAP, RETAINING XDOZZ J MOUNT, RESILIENT XDOZZ HANDLE BRACKET... 2 END OF FIGURE 18-1

47 FIGURE 19. ACCESSORY ITEMS (VR11C)

48 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 22 BODY, CHASSIS, AND HULL ACCESSORY ITEMS GROUP 2202 ACCESSORY ITEMS FIG. 19 ACCESSORY ITEMS (VR11C) 1 XBOZZ CASE, CARRYING... 1 END OF FIGURE 19-1

49 FIGURE 20. DATA PLATE AND DECALS

50 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 2210 DATA PLATES AND INSTRUCTION HOLDERS FIG. 20 DATA PLATE AND DECALS 1 XDOZZ SN-17C DECAL, OPERATING XDOZZ SN-43A DECAL, WARNING XDOZZ SN-47 DECAL, WARNING XDOZZ SN-46A DECAL, INSTRUCTION XDOZZ SN-85 DECAL, INSTRUCTION XDFZZ SN-9 DECAL, SAFETY XOOZZ SN-69 DECAL, IDENT PAOZZ DECAL, WARNING PAOZZ SCREW, DRIVE RD HD... 2 UOC;T77 10 PAOZZ A PLATE, IDENTIFICATIO... 1 END OF FIGURE 20-1

51 FIGURE 21. LOWER UNIT DRIVE MECHANISM (VR11C)

52 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 74 CRANES, SHOVELS, AND EARTHMOVING EQUIPMENT COMPONENTS GROUP 7474 DRIVE MECHANISM FIG. 21 LOWER UNIT DRIVE MECHANISM (VR11C) 1 AFFFF LOWER UNIT ASSEMBLY PAFZZ PLUG, EXPANSION PIN PFFZZ ROD, PISTON PAFZZ PIN, STRAIGHT, HEADLE PCFZZ PACKING, PREFORMED PAFZZ MS SCREW, CAP, SOCKET HE PAFZZ MS C NUT, SELF-LOCKING, HE PFFZZ GUIDE, TUBE, SHORT PFFZZ BUSHING, SLEEVE PFFZZ HOUSING, LOWER UNIT XDOZZ A INDICATOR, SIGHT PFFZZ SPACER, BRG TO SPR PFFZZ SPRING, HELICAL, COMP PFFZZ SPRING, HELICAL COMP XDFZZ SPACER RING PFFZZ RING, PISTON PFFZZ PISTON, LINEAR, ACTUA PAFZZ NAS1021N17 NUT, SELF-LOCKING, HE PAFZZ SPRING, HELICAL, COMP PFFZZ SPRING, HELICAL, COMP XDFZZ PACKING, PREFORMED PFFZZ PLATE, BASE

53 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY 23 PAFZZ MS SCREW, CAP, SOCKET HE PFFZZ RING, BOOT, DUST SEAL PAFZZ MS SCREW, CAP, SOCKET HE PAFZZ /W BOOT, DUST AND MOIST PFFZZ BUSHING, SLEEVE PFFZZ GUIDE, TUBE PAFZZ MS SCREW, CAP, SOCKET HE PAOZZ MS SCREW, CAP, SOCKET HE... 6 END OF FIGURE 21-2

54 FIGURE 22. LOWER UNIT DRIVE MECHANISM (VR11)

55 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 7474 DRIVE MECHANISM FIG. 22 LOWER UNIT DRIVE MECHANISM (VR11) 1 PFFZZ WASHER, FLAT XDFZZ BOOT RETAINER PFFZZ DISK, SOLID, PLAIN XDFZZ ROD PIN PFFZZ ROD, PISTON LINEAR ACTUATING 1 CYLINDER... 6 PFFZZ PACKING, PREFORMED PFFZZ GUIDE TUBE ASSEMBLY PFFZZ BUSHING, SLEEVE PFFZZ BOOT, DUST XDFZZ SPRING, LOWER UPPER PFFZZ SPRING, HELICAL UPPER, OUTER PFFZZ SLEEVE, BUSHING SPRING HOUSING PFFZZ SPRING, HELICAL HOUSING XDFZZ A OIL SIGHT GAGE XDFZZ RETAINING RING PFFZZ SHOE, TAMPER PFFZZ PLATE, BASE PFFZZ PREFORMED PACKING XDFZZ SPRING, LOWER INNER XDFZZ SPRING, LOWER OUTER XDFZZ NUT PFFZZ PISTON, TAMPER... 1 END OF FIGURE 22-1

56 FIGURE 23. SHOE DRIVE MECHANISM

57 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 7474 DRIVE MECHANISM FIG. 23 SHOE DRIVE MECHANISM 1 PFOZZ SHOE, TAMPER PFOZZ SHOE, TAMPER, 4 INCH,WITH 14 INCH 1 EXTENSION... 3 PFOZZ SHOE, TAMPER, 6 INCH,WITH 14 INCH 1 EXTENSION... END OF FIGURE 23-1

58 (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY GROUP 94 REPAIR KITS GROUP 9401 REPAIR KITS FIG. KITS PFFZZ K10009 GASKET AND PREFORMD... 1 GASKET, COVER ( 1) 8-35 GASKET, DIAPHRAGM ( 1) 8-43 GASKET, FUEL PUMP ( 1) 8-40 PACKING, ADJ SCREW ( 2) 8-21 WASHER, ADJUST SCREW ( 2) 8-20 PFFZZ K10117 PARTS KIT, CARBURETO 1 DIAPHRAGM, FUEL PUMP ( 1) 8-39 DIAPHRAGM ( 1) 8-42 GASKET, COVER ( 1) 8-35 GASKET, DIAPHRAGM ( 1) 8-43 GASKET, INLET SEAT ( 1) 8-11 LEVER, INLET CONTROL ( 1) 8-14 NEEDLE, INLET ( 1) 8-12 PACKING, ADJ SCREW ( 2) 8-21 PLUG, BODY CHANNEL ( 1) 8-15 PLUG, WELCH ( 1) 8-16 SCREW ( 1) 8-33 SCREW ASSEM WASHER ( 1) 8-28 SCREW, MN ADJUSTMENT ( 1) 8-19 SCREW, REGULATING ( 1) 8-30 SPRING, ADJUST SCREW ( 2) 8-17 SPRING, INL TENSION ( 1) 8-13 SPRING, RGLT SCREW ( 1) 8-31 STRAINER, FUEL ( 1) 8-36 WASHER, ADJUST SCREW ( 2) 8-20 XDOZZ GASKET, SET 1 CAPACITOR, FIXED, PAP ( 1) COIL ASSEMBLY ( 1) 15-8 CONTACT SET, DISTRIB ( 1) 15-5 SCREW, ASSEM WASHER ( 1) SCREW, BREAKER CLAMP ( 1) SPRING, BREAKER COV ( 1) SPRING, WEDGE, COIL ( 1) 15-7 TERMINAL ( 1) 15-9 GASKET, BEARING CAGE ( 1) 2-4 GASKET, MUFFLER ( 1) 14-4 GASKET, REED PLATE ( 1) 2-11 GASKET, SET ( 1) 3-10 GASKET, SET ( 1) 3-4 KITS-1 END OF FIGURE

59 I (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 95 GENERAL USE STANDARDIZED PARTS GROUP 9501 BULK MATERIEL FIG. BULK 1 PAOZZ HOSE, NONMETALLIC... V END OF FIGURE BULK-1

60 I FIGURE 24. SPECIAL TOOLS.

61 I (1) (2) (3) (4) (5) (6) ITEM SMR PART NO CODE CAGEC NUMBER DESCRIPTION AND USABLE ON CODES(UOC) QTY GROUP 26 TOOLS AND TEST EQUIPMENT GROUP 2604 SPECIAL TOOLS FIG. 24 SPECIAL TOOLS 1 XDFZZ T BOLT, MACHINE BOI:2 PER LETTERED CO END OF FIGURE 24-1

62 SECTION IV CROSS-REFERENCE INDEXES NATIONAL STOCK NUMBER INDEX STOCK NUMBER FIG. ITEM NO. STOCK NUMBER FIG. ITEM NO BULK I-1

63 SECTION IV CROSS-REFERENCE INDEXES NATIONAL STOCK NUMBER INDEX STOCK NUMBER FIG. ITEM NO. STOCK NUMBER FIG. ITEM NO KITS I-2

64 SECTION IV CROSS-REFERENCE INDEXES NATIONAL STOCK NUMBER INDEX STOCK NUMBER FIG. ITEM NO. STOCK NUMBER FIG. ITEM NO KITS I-3

65 SECTION IV CROSS-REFERENCE INDEXES PART NUMBER INDEX CAGEC PART NUMBER STOCK NUMBER FIG. ITEM A AFP A A A A A A A A A A CAA-2W/ J K KITS K KITS K K K K MS MS MS MS MS MS MS MS MS MS C MS21044N MS MS MS M MS MS MS MS MS MS MS MS MS I-4

66 SECTION IV CROSS-REFERENCE INDEXES PART NUMBER INDEX CAGEC PART NUMBER STOCK NUMBER FIG. ITEM MS MS MS MS MT NAS1021N R SN-17C SN-43A SN-46A SN SN SN SN T S UJ-11G T I-5

67 SECTION IV CROSS-REFERENCE INDEXES PART NUMBER INDEX CAGEC PART NUMBER STOCK NUMBER FIG. ITEM S N A I-6

68 SECTION IV CROSS-REFERENCE INDEXES PART NUMBER INDEX CAGEC PART NUMBER STOCK NUMBER FIG. ITEM Z T I-7

69 SECTION IV CROSS-REFERENCE INDEXES PART NUMBER INDEX CAGEC PART NUMBER STOCK NUMBER FIG. ITEM /W I-8

70 SECTION IV CROSS-REFERENCE INDEXES PART NUMBER INDEX CAGEC PART NUMBER STOCK NUMBER FIG. ITEM KITS A X1E RS RS BULK XX A I-9

71 SECTION IV CROSS-REFERENCE INDEXES FIGURE AND ITEM NUMBER INDEX FIG. ITEM STOCK NUMBER CAGEC PART NUMBER BULK KITS KITS K10117 KITS K MS MS MS MS MS A A A A A A A K I-10

72 SECTION IV CROSS-REFERENCE INDEXES FIGURE AND ITEM NUMBER INDEX FIG. ITEM STOCK NUMBER CAGEC PART NUMBER A MS K I-11

73 SECTION IV CROSS-REFERENCE INDEXES FIGURE AND ITEM NUMBER INDEX FIG. ITEM STOCK NUMBER CAGEC PART NUMBER T A MS AFP MS MS CAA-2W/ T S XX A MT MS S MS MS MS MT MS MS N A I-12

74 SECTION IV CROSS-REFERENCE INDEXES FIGURE AND ITEM NUMBER INDEX FIG. ITEM STOCK NUMBER CAGEC PART NUMBER K K UJ-11G MS RS X1E ZA ZA Z MS MS RS MS21044N R MS MS I-13

75 SECTION IV CROSS-REFERENCE INDEXES FIGURE AND ITEM NUMBER INDEX FIG. ITEM STOCK NUMBER CAGEC PART NUMBER MS MS RS MS MS MS MS MS J SN-17C SN-43A SN SN-46A SN SN SN A MS MS C A NAS1021N I-14

76 SECTION IV CROSS-REFERENCE INDEXES FIGURE AND ITEM NUMBER INDEX FIG. ITEM STOCK NUMBER CAGEC PART NUMBER MS MS /W MS MS A T I-15

77

78

79 THE METRIC SYSTEM AND EQUIVALENTS

80 PIN:

81 This fine document... Was brought to you by me: Liberated Manuals -- free army and government manuals Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap watermarks and other junk on it, and sell it. Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it... They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends? I am setting this document FREE. This document was made by the US Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on. I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines: <A HREF= Military and Government Manuals</A> Sincerely Igor Chudov Chicago Machinery Movers