SIGRAM FLUE SYSTEMS LTD

Transcription

1 SIGRAM FLUE SYSTEMS LTD TEL: FAX: WEB: FLUE SYSTEMS FOR INDUSTRIAL & COMMERCIAL APPLICATIONS SINCE 1969 PROJECT WORK SITE SURVEY MANUFACTURE INSTALLATION SYSTEM DE SINGLE SKIN

2 Application Technical Data SYSTEM DE Chimney/Flue System/Connecting Flue Installation Method Operating Mode Dry/Wet Pressure Negative/positive pressure Max. Working pressure 200 Pa Operating temperature 450 C negative pressure (EN ) 400 C negative pressure (EN ) 200 C positive pressure Max. temperature allowed 1000 C negative pressure (EN ) (max. 30min.) 400 C negative pressure (EN ) 200 C positive pressure Material AISI 316L/EN Thickness minimal 0.5mm Sealant Elastomer Fuel Type Natural gas/calor gas/propane gas INSTALLATION NOTES SPECIFICALLY FOR CONDENSING APPLICATIONS. On all condensing applications, system must be fitted with a minimum 3 degree slope back towards the appliance/s. (appliance and/or system drain point required at lowest point/s.) Note: A system slope of 3 degrees equates to 5.2CM per linear metre. Systems must be adequately supported, with horizontal run supports not exceeding two metre centres. Applications SYSTEM DE Shaft liner in renovation projects Air inlet & ventilation systems Flue system for condensing heaters and boilers Chimney renovation Applications SYSTEM DE Stress free thermal expansion Can be connected to System DF High quality stainless steel system High temperature silicone sealing ring Universal application Fully welded system with sealing ring Light weight system Check all parts for possible damage. During installation you may have to use our special installing grease. The installation of the chimney starts at the appliance and then progresses upwards to the terminal. The top of each element can be recognised by the profile edge (fig.1). At the bottom of each section (DE 100) an arrow is printed which indicates the direction of flow. Connect two elements by pushing them vertically into each other. For visual reasons it is advisable to place the welding seams at the rear if possible. The sealing ring in the inner wall must remain in its position and must not be damaged during connection of the elements. When the elements are connected then fix the locking band (fig. 2) Then install the next element as instructed above. DIAMETER CROSS SECTIONAL AREA WEIGHT KG/M Diameter mm Cross Section cm² Weight kg/m PAGE 2

3 DE BOILER CONNECTION LENGTH DE 1000MM LENGTH H H DE 500MM LENGTH DE 250MM LENGTH 250MM LENGTH H H DE 150MM LENGTH DE ADJUSTABLE LENGTH H Hmin Hmax PAGE 3

4 DE 15 DEGREE ELBOW SYSTEM DE DE 30 DEGREE ELBOW K M X Y DE 45 DEGREE ELBOW K M X Y DE 87 DEGREE ELBOW K M X Y DE 45 DEGREE TEE K L M X Y DE 87 DEGREE TEE H h X H h X PAGE 4

5 DE DEGREE TEE DE 87 DEGREE REDUCING TEE H h Ø X X DE CONDENSATE COLLECTOR C/W DRAINPOINT DE END CAP WITHOUT DRAIN 3/4 BSP CONNECTION DE PROBE LENGTH AND DRAIN HORIZONTAL DE PROBE LENGTH AND DRAIN VERTICAL Ø /4 BSP CONNECTION 3/4 BSP CONNECTION PAGE 5

6 DE MESH END TOP DE VENTURI END TOP Ø D DE ALL WEATHER COWL CAP DE RAIN CAP A B D H DE STORM COLLAR Ø A D H h FLAT TRIM PLATE A A B PAGE 6

7 DE INCREASER DE EXCENTRIC INCREASER Ø D H DE REDUCER Ø D To be specified on order DE ADAPTOR DOUBLE FEMALE Ø D H DE DRAUGHT STABILIZER DE LOCKING BAND Ø PAGE 7

8 DE FLAT ROOF FLASHING SYSTEM DE DE SLOPE ROOF FLASHING D A SQ DE LEAD FLASHING DEGREE Ø A N/A N/A N/A C N/A N/A N/A C N/A N/A N/A H N/A N/A N/A DE MOUNTING BAND (LIGHT WEIGHT) A N/A N/A N/A C N/A N/A N/A C N/A N/A N/A DE SPLIT RINGS Ø DE WALL BAND ADJUSTABLE X b H PAGE 8

9 DE SWING RING BAND DE WALL SUPPORT BAND (ADJUSTABLE) CEMBV 2 A -200 CEMBV 3 A CEMBV 4 A Ø X DE SUPPORT ARMS C/W FLUE RING DE SUPPORT ARMS C/W FLUE RING A N/A N/A B N/A N/A D N/A N/A A B D DE SUPPORT ARMS C/W FLUE RING DE GUY WIRE BAND A B D PAGE 9

10 TWIN-WALL PRODUCT RANGE ALSO AVAILABLE REFER TO SYSTEM DF CATALOGUE Whilst every effort has been made to provide reliable information and dimension accuracy, Sigram Flue Systems limited do not hold themselves responsible for possible errors of an editorial nature, however caused. Sigram are committed to the concept of continuous quality and improvement, therefore we reserve the right to alter product specification without notice. SIGRAM FLUE SYSTEMS LTD UNIT 8 SHEPLEY INDUSTRIAL ESTATE SOUTH SHEPLEY RD AUDENSHAW MANCHESTER M34 5DW TEL: FAX: sales@sigram.co.uk WEB: