Table of Contents. Equity

Transcription

1 Table of Contents Introduction finishes 3 fabrics 4 General information Layout Comparison 8 Worksurfaces, tables, peninsula, and transition tops 9 Panels, Connections, Power and Accessories Generation 1 fabric panel 12 Generation 2 Insert Panel 14 Generation 1 16 Generation 3 32 Personal Flat Bi-Fold Door 49 Add-on Screens 50 Stack-On Panels 51 Stack-On Insert Panel 52 Stack-On Fabric Panel 56 Stack-on Posts 60 Currents 61 How to order electrical systems 63 Technical data 64 Ceiling infeeds 66 E Series electrical 70 O Series electrical 75 O Series electrical components 77 Electrical/Communication accessories 78 DataWay 79 DataTrak 81 Panel accessories 83 Worksurfaces and Tables Worksurface loading/support 85 General information 86 EW1 Worksurfaces 90 EW2 Worksurfaces 94 EW3 Worksurfaces 98 Worksurface, blended double corner, curved cluster, corner round 102 Worksurfaces, D, P Worksurface, half round 105 Cascade Edge Worksurfaces Tables 116 Counter caps, straight 118 Counter caps, corner 119 Veneer Worksurface 120 Veneer tables 122 Veneer counter caps, straight 124 Veneer counter caps, corner 125 Worksurface supports and accessories 126 Freestanding General information 128 Preconfigured 129 Overdesk shelf and cabinet (painted/fabric) 131 Preconfigured, D unit, P/9 unit, 132 Freestanding support components 134 Pedestals and Files Floorstanding pedestals 136 Mobile, suspended and double-width pedestals 137 Pedestal accessories 139 Copyright 2007 Knoll, Inc. All rights reserved. All prices effective 2/15/ PLEQ0507

2 Cabinets and Shelves Corner shelves 140 shelves and overhead cabinets 141 shelf, EDP 143 shelves and overhead cabinet 144 Upmount overhead cabinets and shelf 146 Veneer overhead cabinets 148 Veneer and upmount overhead cabinets 150 overhead cabinet back 151 suspended lateral files 153 Tackboard for panels 154 T5 Task Light 155 Chicago Raceway Panels and Related Electrical Components General Information 156 Generation 1 Fabric panel - Chicago raceway 157 Generation 2 Insert panel - Chicago raceway 159 Generation 1 Steel panel - Chicago raceway 161 Generation 3 Fabric panel - Chicago raceway 162 Generation 3 Insert panel - Chicago raceway 164 Generation 3 Steel panel - Chicago raceway 166 Generation 1 ceiling infeed modules- Chicago raceway 168 Generation 3 ceiling infeed modules- Chicago raceway 169 Base infeed module 170 Alpha-Numeric Index 171 KnollKey Lock Program 183 Key-alike policy to match locks 184 General Ordering Information 185 2

3 finishes Core finishes Laminates 111 Jet Black 114 Folkstone Grey (was LA) 117 Soft Grey (was M42) 118 Bright White 119 Pumice (was LF) 121 Micro Grey 122 Brushed Sand 123 Brushed Grey 124 Medium Cherry 125 Natural Maple 126 Natural Cherry 127 Walnut 128 Fog 129 Micro Sand Worksurface Edge 111 Jet Black 113 Dark Grey (was Y3) 114 Folkstone Grey (was LA) 115 Medium Grey (was Y2) 117 Soft Grey (was E) 118 Bright White 119 Pumice (was LF) 124 Medium Cherry 125 Natural Maple 126 Natural Cherry 127 Walnut 128 Fog Knoll Color Program Painted Trim EP3 Panels all other painted components P1 Finishes 111 Jet Black 112 Brown 113 Dark Grey (was Y3) 114 Folkstone Grey (was LA) 115 Med. Grey (was Y2) 116 Sandstone 117 Soft Grey (was E) Legacy finishes Note: Specify Legacy finishes to match existing product only. Legacy finishes are not available for new customers. Note: EP1 and EP2 panels and components are only available in P1 or P3 LEGACY paint trim unless otherwise noted. Legacy Laminates for worksurfaces, cabinet fronts and door panels MC CM M5 MP58 M95 M1 MP70 e CP276 PA M96 SD M89 B M80 WM ES7 MR6 Caramel Maple Clear Maple Dark Neutral Deep Mahogany Grey Granite Light Grey Light Oak Markerboard Pearwood Rose Granite Sand Med. Grey (Slate) Snow Taupe Warm Cherry White Essence Winter Grey Matrix Legacy Worksurface Edge 2mm edgeband and 1 ergonomic edge D Dark Neutral B Snow R Taupe 115 Medium Grey (was Y2) 113 Dark Grey (was Y3) SD Sand 2mm edge only MC Caramel Maple CM Clear Maple WM Warm Cherry MT Metal Legacy finishes (cont.) Legacy Painted Trim EP1, EP2 Panels for painted parts, accessories, panel trim, cabinet trim and pedestals unless otherwise noted. P1 Finishes D Dark Neutral R Taupe 113 Dark Grey (was Y3) 115 Med. Grey (was Y2) 117 Soft Grey (was E) P2 Finishes (not available on generation1 panels and panel components) H Beige Metallic W Light Tan Metallic P3 Finishes 613 Silver (was 3) Insert Options for insert panels, stack-on panels and add-on screens. Plexiglass CL Clear IC Ice SM Smoked TR Translucent Perforated Steel See painted trim colors. Polycarbonate PC Clear Lumasite (stack-on panels and add-on screens only) LF Frost Techgrain Veneer for worksurfaces and cabinet fronts. e 9 American Cherry (was V09) e 16 Deep Mahogany (was V96) e 4 Maple (was V04) e 7 Medium Brown Mahogany (was V07) e T Natural (was V0T) P2 Finishes 611 Beige Mist Metallic 612 Medium Metallic Grey Note: Laminates and other finishes may vary in color due to different dye lots. Slight variations are normal. P3 Finishes 118 Bright White 613 Silver (was 3) 3

4 fabrics e = Extended Leadtime Note: All 72 wide fabric covered cabinets with single door, tackboards and privacy screens require that the textile is railroaded (turned 90 degrees) for application. This must be considered when applying a patterned textile. Fabrics Grade 10 Bailey II W359-1 Belmont Silver W359-2 Sherman Pewter W359-3 Vernon Green W359-4 Waldo Blue W359-5 Colby Blue W359-6 Lincoln W359-7 Acadia W359-8 Aroostook W359-9 Allagash Mist Broadcloth W288-1 Pumice W288-2 Taupe W288-3 Medium Beige W288-4 Camel W288-5 Sand W288-6 Silver W288-7 Mineral W288-8 Grey Foundation e W351-1 Natural e W351-2 Greige W351-3 Corn Silk e W351-4 Fog e W351-5 Biscuit e W351-6 Zephyr W351-7 Willow e W351-8 Sandstone e W351-9 Camel e W Orange Wood e W Leaf W Sea W Slate e W Plum e W Ebony W Pearl Growth Spurt W692-1 Birch W692-2 Lotus W692-3 Kernel W692-4 Barley W692-5 Alfalfa W692-6 Aloe W692-7 Grain W692-8 Flaxen W692-9 Quarry W Blue Corn Newbury W812-1 Sand W812-2 Ash W812-3 Light Charcoal W812-4 Teal W812-5 Light Pine W812-7 Light Wine e W812-8 Melange W812-9 Malachite Grade 10, continued Solid Crepe e W257-1 Dove e W257-2 Trench e W257-3 Bark e W257-4 Tea Green e W257-5 China Blue e W257-6 Blue Pine e W257-7 Skipper e W257-8 Gun Metal Symbolic Detail W693-1 Rainy W693-2 Atmosphere W693-3 Eucalyptus W693-4 Lightning Bug W693-5 Ginseng Root W693-6 Whispering Willow W693-7 Moonbeam W693-8 Ebony and Ivory Tailor Made W133-1 Tusk W133-2 Muslin W133-3 Flight W133-4 Birch W133-5 Flax Seed W133-6 Sage W133-7 Tumbleweed W133-8 Clay W133-9 Twig W Mahogany W Magenta W Knoll Red W Persimmon W Citronella W Carribean W Deep Sea Taurus e T300 T302 T303 T307 T308 Natural Smoke Stone Sky Mist Versatility e W432-1 Chalk W432-2 Marble W432-3 Chino e W432-4 Buttercup W432-5 Cappuccino e W432-6 Sage W432-7 Dove e W432-8 Graphite W432-9 Sky e W Haricot Vert e W Iris Grade 15 Belgrade e W256-1 e W256-2 e W256-3 e W256-4 Dear-isle Dover grey Bluehill Liberty Marche e W321-5 Taupe e W321-7 Light Grey e W True Blue e W Burgundy Regency/Fairfield B021 Pearl B081 Medium grey B191 Light neutral B701 Blue neutral B781 Medium blue W Sand beige e W Natural e W Amethyst e W Blueberry e W Wedgewood e B111 Charcoal e B211 Medium neutral e B632 Mauve e B711 Ice e B752 Light blue e B761 Buff e B771 Quarry e B811 Ultramarine e B821 Dark blue Visage W320-2 Oatmeal W320-5 Pewter W320-6 Slate e W320-4 Light grey e W320-8 Mauve e W Cadet blue Grade 20 Banyan e W443-1 e W443-2 e W443-3 e W443-4 e W443-5 e W443-6 e W443-7 e W443-8 e W443-9 Birch Dogwood Maple Yew Bamboo Cedar White Oak Ash Mulberry Bauhaus Block e W296-1 Oyster e W296-2 Pumice e W296-3 Parchment e W296-4 Cinnamon e W296-5 Maize e W296-6 Desert e W296-7 Celadon e W296-8 Sage e W Eucalyptus e W Emerald e W Indigo e W Slate e W Granite e W Sesame Boardwalk e W911-1 Straw e W911-2 Siam e W911-3 Pebble e W911-4 Azure Clarity e W281-1 Almond Blond e W281-2 Natural e W281-3 Croissant W281-4 Raffia Basket W281-5 Almost Aqua W281-6 Moonstone e W281-7 Violet Echo e W281-8 Tourmaline W281-9 Black Tie e W Cabernet e W True Teal 4

5 fabrics e = Extended Leadtime Note: All 72 wide fabric covered cabinets with single door, tackboards and privacy screens require that the textile is railroaded (turned 90 degrees) for application. This must be considered when applying a patterned textile. Fabrics Grade 20, continued Criss Cross e W305-1 Pearl e W305-2 Parchment e W305-3 Taupe e W305-4 Aluminum e W305-5 Eucalyptus e W305-7 Platinum e W305-8 Granite e W305-9 Obsidian Devon W809-1 Granite e W809-2 Sand W809-3 Opal W809-4 Light Grey W809-5 Pewter W809-6 Steel W809-7 Cadet Blue W809-8 Malachite W809-9 Wisteria e W Adobe Frequency e W340-1 Alabaster e W340-2 Dove Grey e W340-3 Solar e W340-4 Spring Green e W340-5 Cornflower e W340-6 Eucalyptus Labyrinth e W352-2 Sand e W352-3 Pebble Grade 20, continued Melbourne e W228-8 Charcoal e W Wheat e W Clay e W Oatmeal Outback W229-5 Ocean W229-8 Lilac W Aloe W Blush Playa e W422-3 e W422-5 e W422-6 Keylime Pebble Coral Reflect e W884-1 Ice e W884-2 Titanium e W884-3 Sterling e W884-4 Steel e W884-5 Ecru e W884-6 Brass e W884-7 Solar e W884-8 Peridot e W884-9 Ember e W Target e W Lapis e W Concord e W Sharkskin Grade 20, continued Walkabout W Grey e W Ivory W Sage Weave Three W298-3 Alabaster W Bayshore W Griege W Pumice e W298-1 Cellophane e W298-2 Talc e W298-4 Tea e W298-5 Bone e W298-6 Camel e W298-7 Santa Fe e W298-8 Copper e W298-9 Chiffon e W Celedon e W Sage e W Garden e W Salt air e W Pewter e W Lilac e W Amethyst e W Obsidian Grade 30 Basket draft e W249-1 Aluminum e W249-2 Silver e W249-3 Luster white e W249-4 Moon e W249-5 Opalescent e W249-6 Gold e W249-7 Topaz e W249-8 Pewter e W249-9 Mineral e W Lead e W Petrol e W Purpline e W Pool e W Herb e W Reef Elan e W444-1 e W444-2 e W444-3 e W444-4 e W444-5 e W444-6 e W444-7 e W444-8 Milkweed Arctic Ginger Marigold Mango Pear Turquoise Spirit Litchfield e W808-1 e W808-3 e W808-4 e W808-6 Oyster Khaki Ice Teal 5

6 fabrics e = Extended Leadtime Note: All 72 wide fabric covered cabinets with single door, tackboards and privacy screens require that the textile is railroaded (turned 90 degrees) for application. This must be considered when applying a patterned textile. Fabrics Grade 30, continued Flow e W565-1 Whitewash e W565-2 Fossil e W565-3 Celery e W565-4 Strawflower e W565-5 Amber e W565-6 Bamboo e W565-7 Pebble e W565-8 Woodsage Harmony e W232-1 Champagne e W232-2 Pearl e W232-3 Amber e W232-4 Flint e W232-5 Ivy e W232-6 Graphite Promenade e W913-1 Frost e W913-2 Bisque e W913-3 Sisal e W913-4 Quarry Walls of rain e W923-1 Oatmeal Grade 35 Saxony plus S801 Sand S809 Soft blue S812 Opal S813 Slate S815 Light teal e S805 Clay e S806 Burgundy e S808 Saphire e S816 Mist e S726 Teal e S819 Cornflower e S823 Silver grey Grade 40 Analogy e K614-1 e K614-2 e K614-3 e K614-4 e K614-5 e K614-6 e K614-7 e K614-8 Pearl Glacier Fossil Jute Golden Pearl Grey Shadow Lead Box step e W325-1 Pearl e W325-2 Mallow e W325-3 Parchment e W325-4 Lichen e W325-5 Maple e W325-6 Cork e W325-7 Celedon e W325-8 Thistle e W325-9 Amber e W Cornflower e W Sapphire e W Laurel e W Currant Eurythimic e W268-1 Alabaster e W268-2 Feather grass e W268-3 Reed e W268-4 Almond e W268-5 Phantom e W268-6 Antelope e W268-7 Metaline e W268-8 Graphite Foil Rap e W535-1 White Light e W535-2 Mercury e W535-3 Platinum Blonde e W535-4 Silver e W535-5 Patina e W535-6 Bronze e W535-7 Gold Leaf e W535-8 Verdigris e W535-9 Steel Blue Freefall e W922-1 Natural Grade 40, continued Hard Rock e W Alabaster e W Marble e W Moonstone e W Quartz e W Ochre e W Patina e W Tiger Eye e W Lapis Heavy Metal e W539-1 Titanium e W539-2 Pewter e W539-3 Golden Nugget e W539-4 Oxide e W539-5 Ore e W539-6 Brass Rubbing e W539-7 Armor Metaphor e K612-1 Zinc e K612-2 Canvas e K612-3 Oyster e K612-4 Drizzle e K612-5 Bamboo e K612-6 Ochre e K612-7 Cinnamon e K612-8 Iron e K612-9 Optical White Palladium e W Talc e W Abalone e W Calcite e W Bronze e W Olivine e W Titanium e W Flint e W Hematite Sennit e W337-1 e W337-2 e W337-4 e W337-5 e W337-6 Sierra e R13 e R14 e R17 e R18 e R19 e R21 Oatmeal Sand Olivine Hyacinth Azure Sky Mica Blackberry Steel Beige Marine Grade 40, continued Spinoff Nuance e W319-1 Honey e W319-2 Greige e W319-3 Onyx e W319-4 Autumn e W319-5 Copper e W319-8 Cranberry e W Wineberry e W Parchment e W Beige Grade 45 Casual Elegance e W920-1 Neutral Dristi e K872-1 Shadow e K872-2 Snowcap e K872-3 Sea Salt e K872-4 Alfalfa e K872-5 Chamomile e K872-6 Lemon twist e K872-7 Cumin e K872-8 Lemongrass e K872-9 Sky e K Tibetan red e K Delphinium e K Carob e K Anise COM (Customer s Own Material) COM can be applied to Dividends products on a select basis. Please consult your Knoll Customer Service Representative for details on the COM approval process and testing requirements. Pricing for COM fabrics is at Grade 10. Note: Always contact your Customer Service Representative prior to sending any COM (including pre-approved KnollTextiles) to the manufacturing facility. 6

7 General information Fabric Panels incorporate a mineral wool core construction. Fabric panels are acoustical and fully tackable. The base raceway is nominally 5 high. Insert Panels are constructed with a tapered aluminum frame that is mitered in the corners. Insert panels may be ordered with a variety of standard insert options or as an open frame for complete accessibility through the panel. Steel Panels and end panels have a honeycomb core construction wrapped with trim colored steel skins. They are neither tackable nor acoustical. Access Panels allow for air flow or utility access below worksurface height while providing a fabric privacy screen above the worksurface. Stack-On Panels connect on the top of any standard panel to provide additional privacy or new aesthetic options and are also load bearing. Door Panels are available with laminate skins mounted to a trim colored, painted frame and natural aluminum threshold. The 42 and 48 wide doors provide a minimum opening clearance of 32 and are ADA compliant. Post Connectors are 1 1/2 diameter and required at every panel connection and panel end (except when postless end assembly is used). Posts are painted to match the selected trim finish and include an adjustable glide on the bottom for leveling. Fabric, Insert, Steel and Access panels all accept electrical components. panels distribute power through the office and directly to the individual work station through field-installed modular, electrical wiring components in the base of the panels. The panel base is factory prepared to accept a terminal block in a centered location where two 20-amp receptacles can be installed; one on each side of a panel, arranged back-to-back. An auxiliary side mount duplex receptacle is also available and plugs directly into the side of the terminal block connector end when a second duplex receptacle is required. The panel base is capable of supporting up to 102 Category 5,.20 cables (40 at 40 fill rate) without electric and 36 Category 5,.20 cables (14 at 40 fill rate) in an electrified panel. The panel base cover provides openings for receptacles and/or communication outlets, which can be covered when not in use. All panel bases provide a cable management segment to facilitate lay-in of workstation cables and cords. Width dimension of all panels is centerline to centerline of adjacent post connectors. Panel thickness is 1 1/2. Panel thick- ness at the base covers is 2. For any code compliance testing data, please contact your Customer Service Representative. See Finishes and Fabrics pages for appropriate finish options. Environmental Impact takes great pride in providing one of the most environmentally friendly furniture systems available on the market today. The laminate furniture system is manufactured with greater than 40 percent recycled material. A portion of the composite wood products used in the manufacture of the system are derived from Forest Stewardship Council (FSC)- certified forests. None of the glues or adhesives used in producing the product contain volatile organic compounds. Clean technology powder coating is used on the metal components as well as the pedestals and overhead cabinets. Low mercury, high-efficiency lighting is used in all lights. The steel and plastic materials used to construct can be recycled after the product s life. The system is also designed to be cleaned with low environmental impact materials. The clean technology used to manufacture the system results in negligible off-gassing from the product. is a Greenguard-registered product, awaiting certification. LEED Credits The sustainable design of the system can help customers achieve the following Commercial Interiors LEED credits: Credit 4.1 and 4.2 Recycled Content: The standard furniture system has a recycled content greater than 40 percent. Credit 7.0 Certified Wood: The wood materials used to construct the system can be chain of custody certified from FSC-certified forests. Credit 4.5 Low Emitting Materials, Furniture and Furnishings: The standard system has been tested and is Greenguard-registered, awaiting certification. The sustainable design of the system can help customers achieve the following New Construction LEED credit: Credit 4.1 Recycled Content: The system has a post-industrial recycled content greater than 40 percent, which can help obtain an Innovation credit in this category. Credit 7.0 Certified Wood: The wood materials used to construct the system can be chain of custody certified from FSC-certified forests. The sustainable design of the system can help customers achieve the following Existing Building Leed credits: Prerequisite 1 Waste Management: Low mercury lighting is supplied in all lights. Credit 4.0 Recycled Content: has a post-industrial recycled content of more than 40 percent, which can help obtain an Innovation credit in this category. Credit 5.0 Green Housekeeping: The system is designed to be cleaned with low-impact environmental cleaning fluids. Credit 7.0 Certified Wood: The wood materials used to construct the system can be chain of custody certified from FSC-certified forests. 7

8 120 Layout Comparison The 120-degree planning model provides comparable or greater square footage per workstation than typical cubicle layouts (comparisons are illustrated on this page). At the same time, 120 allows for a more natural space, creating a more comfortable place to work. Maintaining a consistent 48 module promotes improved asset management and a reduction of reconfiguration costs. Townhouse Sq. Feet = panels each 6 x6 Sq. Feet = 36 6 panels Big House Sq. Feet = panels 8 x8 Sq. Feet = 64 7 panels Apartment Sq. Feet = panels 4 x6 Sq. Feet = 24 4 panels Full House Sq. Feet = panels 6 x7 Sq. Feet = 42 7 panels 8 Open House stations Sq. Feet= panels Open House Sq. Feet = panels 6 x6 Sq. Feet = 36 6 panels 8 station cluster Each station 6 x6 Sq. Feet = panels 8

9 Worksurfaces, tables, peninsula, and transition tops These worksurfaces are designed specifically for 120. The (L/R) suffix at the end of a pattern number indicates a defined pedestal location. If the worksurface has no defined pedestal location, the (L/R) represents the curved side of the top. All tops and tables are available with 2mm edge band or a 1 ergonomic edge. Worksurface: W3 This worksurface, combined with the T3 Transition top, works best with the apartment layout. This application allows for stations on both sides of the spine, and is ideal for high density layouts. Available in extended versions for placement directly next to another worksurface. Worksurface: W6 (L/R) In the big house, full house or open house, this worksurface allows for a pedestal on one side (determined by the L/R). Applications for this top include a call center with the open house, technical applications with the full house, and managerial layouts with the big house. left right Worksurface: W4 This top works well in the open house, full house, and big house layouts for call center, professional, and managerial applications. Worksurface: W7 (L/R) Used in conjunction with a T4 transition top, the W7 worksurface provides a great teaming space when the townhouse layout is used. The open house layout incorporates the T2 transition top for professional or technical stations with shared space for conferencing. Available in extended versions for placement directly next to another worksurface. left right Worksurface: W5 (L/R) With transition top T5 and this worksurface, teaming is made easy using the townhouse or open house layout. The shared space allows for call center, professional, or technical applications. Worksurface: W11 / W1118 (L/R) This top is a spacious option for a technical station in the open house layout. Adding a T2 transition top provides additional teaming space. The W11 surface also fits nicely in a private managerial office or a full house professional application. left right left right 9

10 Worksurfaces, tables, peninsula, and transition tops Worksurface: W12 / W1218 (L/R) This top, with the T5/T518 transition top provides a technical office with shared conferencing space in the open house layout. The 18 return allows ample space in the supervisory application of the full house. Transition Tops Transition tops require columns (not included) for support. Flat brackets (not included) are required to attach transition tops to adjacent worksurfaces. left right Transition top: T2 Transition top: T218 Worksurface: W13 / W1318 (L/R) This surface provides a teaming space with the T2/T218 transition in the open house layout. The W13/W1318 creates generous worksurface space in the full house as well as the management layout of the big house. Transition top: T3 left right Transition top: T4 Transition top: T5 Transition top: T worksurfaces use cantilevers as their main form of support. A cantilever must be used at each post location to support worksurfaces properly. A pedestal may be used for support, where applicable, in conjunction with cantilevers. Standard 120 worksurface height is approximately 28, worksurfaces and other components are designed to be complemented with standard height Calibre pedestals. Standard and height Calibre pedestals may also be used. Worksurface height will be approximately 29 with these components. 10

11 Worksurfaces, tables, peninsula, and transition tops Peninsula Tops Table Tops Table top: DT54 Diamond Table Peninsula top: P1 Table top: MT38 Small Mushroom Table Peninsula top: P2 right hand Table top: MT44 Large Mushroom Table Peninsula top: P2 left hand Table top: TT41 Small Triangle Table Table top: TT50 Large Triangle Table Peninsula tops provide additional workspace in a big house layout. Peninsula tops are freestanding and supported by table legs, columns or a combination of both. Table tops are suppported with table legs (ordered separately). Table legs are available in sets of 3 or 4 legs and come with either casters or glides. Mushroom and diamond tables require 4 legs each. Triangle tables require 3 legs. Table legs 11

12 Generation 1 fabric panel 28 thru 48 high description w h pattern no Fabric panel 28 high EP1FA1228R $440. $453. $476. $485. $497. $506. $515. $528. n/a $ EP1FA1828R n/a EP1FA2428R n/a EP1FA3028R n/a EP1FA3628R n/a EP1FA4228R n/a EP1FA4828R n/a EP1FA6028R n/a 50. add for P2 add for P3 40 high EP1FA1240R n/a EP1FA1840R n/a EP1FA2440R n/a EP1FA3040R n/a EP1FA3640R n/a EP1FA4240R n/a EP1FA4840R n/a EP1FA6040R n/a high EP1FA1248R n/a EP1FA1848R n/a EP1FA2448R n/a EP1FA3048R n/a EP1FA3648R n/a EP1FA4248R n/a EP1FA4848R n/a EP1FA6048R n/a 50. Example: EP1FA3648R, W3513, 117 EP1FA Fabric panel 36 Width 48 Height R Raceway W351-3 Foundation, Corn Silk 117 Soft grey trim Specify fabric and trim color. Post assemblies or connection elements must be ordered seperately. Note: Power duplexes cannot be installed on 12 W panels. Side mount receptacles available in 24 W panels and wider while using E series power. Electrical components must be ordered separately. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Note: P2 trim colors are not available on EP1 panels and panel components. 12 Panel is fabric covered. If two different fabrics are used on one panel, price will reflect cost of the more expensive panel fabric. NOTE: EP1 & EP2 Panels and components are available in legacy colors only.

13 Generation 1 fabric panel 53 thru 80 description type w h pattern no Fabric panel 53 high EP1FA1253R $486. $499. $524. $535. $548. $558. $568. $583. n/a $ EP1FA1853R n/a EP1FA2453R n/a EP1FA3053R n/a EP1FA3653R n/a EP1FA4253R n/a EP1FA4853R n/a EP1FA6053R n/a 50. add for P2 add for P3 Panels, Connections, Power and Accessories 60 high EP1FA1260R n/a EP1FA1860R n/a EP1FA2460R n/a EP1FA3060R n/a EP1FA3660R n/a EP1FA4260R n/a EP1FA4860R n/a EP1FA6060R ,011. 1,029. 1,056. n/a high EP1FA1265R n/a EP1FA1865R n/a EP1FA2465R n/a EP1FA3065R n/a EP1FA3665R n/a EP1FA4265R n/a EP1FA4865R n/a EP1FA6065R ,018. 1,045. 1,063. 1,082. 1,110. n/a high EP1FA1280R n/a EP1FA1880R n/a EP1FA2480R n/a EP1FA3080R n/a EP1FA3680R n/a EP1FA4280R ,002. n/a EP1FA4880R ,000. 1,028. 1,046. 1,064. 1,091. n/a EP1FA6080R 1,061. 1,092. 1,145. 1,167. 1,199. 1,220. 1,242. 1,273. n/a 50. Example: EP1FA2460R, W3513, 117 EP1FA Fabric panel 24 Width 60 Height W351-3 Foundation,Corn Silk 117 Soft grey trim Specify fabric and trim color. Post assemblies or connection elements must be ordered seperately. Note: Power duplexes cannot be installed on 12 W panels. Side mount receptacles available in 24 W panels and wider while using E series power. Electrical components must be ordered separately. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Note: P2 trim colors are not available on EP1 panels and panel components. 13 Panel is fabric covered. If two different fabrics are used on one panel, price will reflect cost of the more expensive panel fabric. NOTE: EP1 & EP2 Panels and components are available in legacy colors only.

14 Generation 2 Insert Panel (compatible with generation 1 panel components only) description type w d h pattern no. open frame OF plexiglas PG* perforated steel PS marker board MB polycarbonate PY* add for P2 finishes add for P3 finishes Insert panel 28 high EP2( )1228R $469. $630. $593. $593. $547. n/a $ EP2( )1828R n/a EP2( )2428R n/a EP2( )3028R n/a EP2( )3628R n/a EP2( )4228R n/a EP2( )4828R n/a EP2( )6028R n/a high EP2( )1240R n/a EP2( )1840R n/a EP2( )2440R n/a EP2( )3040R n/a EP2( )3640R n/a EP2( )4240R n/a EP2( )4840R n/a EP2( )6040R ,098. 1,006. 1, n/a high EP2( )1248R n/a EP2( )1848R n/a EP2( )2448R n/a EP2( )3048R n/a EP2( )3648R n/a EP2( )4248R , n/a EP2( )4848R , n/a EP2( )6048R ,226. 1,098. 1,098. 1,047. n/a high EP2( )1253R n/a EP2( )1853R n/a EP2( )2453R n/a EP2( )3053R n/a EP2( )3653R ,073. 1, n/a EP2( )4253R ,108. 1,108. 1, n/a EP2( )4853R ,123. 1,133. 1, n/a EP2( )6053R ,247. 1,164. 1,164. 1,062. n/a 50. * All Colors Example: EP2PY3648R, PC, 613 EP2PY Polycarbonate Insert Panel 36 Width 48 Height R Raceway PC Polycarbonate Clear 61 Silver trim Specify insert type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Topcaps and base raceway covers are included with panels. Posts and post connectors must be ordered separately. NOTE: P2 trim colors are not available on EP2 panels or panel components. Generation 2 insert panels incorporate the generation 3 mitered panel frame with generation 1 topcaps and base raceway covers and will only work with generation 1 panels and panel components. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 14

15 Generation 2 Insert Panel (compatible with generation 1 panel components only) description type w d h pattern no. open frame OF plexiglas PG* perforated steel PS marker board MB polycarbonate PY* add for P2 finishes add for P3 finishes Insert panel 60 high EP2( )1260R $528. $759. $700. $700. $651. n/a $ EP2( )1860R n/a EP2( )2460R n/a EP2( )3060R , n/a EP2( )3660R ,035. 1,141. 1, n/a EP2( )4260R ,130. 1,177. 1, n/a EP2( )4860R ,222. 1,202. 1, n/a EP2( )6060R ,370. 1,245. 1,245. 1,165. n/a 50. Panels, Connections, Power and Accessories 65 high EP2( )1265R n/a EP2( )1865R n/a EP2( )2465R n/a EP2( )3065R , n/a EP2( )3665R ,046. 1,191. 1, n/a EP2( )4265R ,141. 1,228. 1, n/a EP2( )4865R ,397. 1,397. 1, n/a EP2( )6065R ,423. 1,414. 1,414. 1,175. n/a high EP2( )1280R n/a EP2( )1880R n/a EP2( )2480R ,060. 1,046. 1, n/a EP2( )3080R ,228. 1,076. 1, n/a EP2( )3680R ,334. 1,316. 1, n/a EP2( )4280R ,538. 1,346. 1,346. 1,094. n/a EP2( )4880R ,552. 1,491. 1,491. 1,109. n/a EP2( )6080R ,767. 1,540. 1,540. 1,332. n/a 50. * All Colors Example: EP2PY3648R, PC, 613 EP2PY Polycarbonate Insert Panel 36 Width 48 Height R Raceway PC Polycarbonate Clear 61 Silver trim Specify insert type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Topcaps and base raceway covers are included with panels. Posts and post connectors must be ordered separately. NOTE: P2 trim colors are not available on EP2 panels or panel components. Generation 2 insert panels incorporate the generation 3 mitered panel frame with generation 1 topcaps and base raceway covers and will only work with generation 1 panels and panel components. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 15

16 Generation 1 Steel panels description type w h pattern no. list price Steel panel 28 high EP1SP2428Re $411. n/a $ EP1SP3028Re 444. n/a EP1SP3628Re 476. n/a EP1SP4228Re 505. n/a EP1SP4828Re 538. n/a 100. add for P2 add for P3 40 high EP1SP1240Re 349. n/a EP1SP1840Re 386. n/a EP1SP2440Re 411. n/a EP1SP3040Re 444. n/a EP1SP3640Re 476. n/a EP1SP4240Re 505. n/a EP1SP4840Re 538. n/a high EP1SP1248Re 359. n/a EP1SP1848Re 397. n/a EP1SP2448Re 437. n/a EP1SP3048Re 471. n/a EP1SP3648Re 506. n/a EP1SP4248Re 547. n/a EP1SP4848Re 584. n/a high EP1SP1260Re 375. n/a EP1SP1860Re 423. n/a EP1SP2460Re 468. n/a EP1SP3060Re 515. n/a EP1SP3660Re 563. n/a EP1SP4260Re 609. n/a EP1SP4860Re 655. n/a high EP1SP1265Re 381. n/a EP1SP1865Re 433. n/a EP1SP2465Re 484. n/a EP1SP3065Re 535. n/a EP1SP3665Re 583. n/a 100. Example: EP1SP2428R, 117, 117, 117 EP1SP Generation 1 Steel Panel 24 Width 28 Height R Raceway 117 Finish side Finish side Soft grey trim Specify surface and trim color. NOTE: P2 trim colors are not available on EP1 panels or panel components. Electrical components must be ordered separately. Topcaps and base raceway covers are included with panel. Posts and post connectors must be ordered separately. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 16

17 Generation 1 Steel panels description type w h pattern no. list price Steel panel 65 high EP1SP4265Re $634. n/a $ EP1SP4865Re 685. n/a 100. add for P2 add for P3 Panels, Connections, Power and Accessories 80 high EP1SP1280Re 393. n/a EP1SP1880Re 458. n/a EP1SP2480Re 523. n/a EP1SP3080Re 583. n/a EP1SP3680Re 646. n/a EP1SP4280Re 708. n/a EP1SP4880Re 773. n/a 100. Example: EP1SP2428R, 117, 117, 117 EP1SP Generation 1 Steel Panel 24 Width 28 Height R Raceway 117 Finish side Finish side Soft grey trim Specify surface and trim color. NOTE: P2 trim colors are not available on EP1 panels or panel components. Electrical components must be ordered separately. Topcaps and base raceway covers are included with panel. Posts and post connectors must be ordered separately. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 17

18 Generation 1 Door Panels and shrouds description type w d h pattern no. list price 36 Door panel LH laminate door EP1DL36L $1,426. n/a $50. RH laminate door EP1DL36R 1,426. n/a 50. add for P2 add for P3 42 ADA door panel LH laminate door EP1DL42L 1,670. n/a 50. RH laminate door EP1DL42R 1,670. n/a 50. Example: EP1DL42L, 117, 117, 117, 117 EP1DL Steel door panel 42 Width L Left handed 117 Soft Grey Front finish 117 Soft Grey Back finish 117 Soft Grey edgeband 117 Soft Grey trim Specify one surface and/or trim color, as appropriate. The direction the door pivots away from you determines the hand. Post and post connectors must be ordered separately. The door frame requires perpendicular support on the hinged side when the door is in an open position. 18 Two doors may not be placed back to back while sharing a single post connection. Doors in this application will not be properly supported and therefore no shroud exists to cover a back-to-back base opening. All 42 and 48 wide doors provide a minimum opening clearance of 32 and are compliant with the Americans with Disabilities Act. The 36 door opening is less than 32 and is not ADA compliant. All doors come with locking lever handset. Handset is ADA compliant. An adaptor cup is included to connect the door to adjoining panels. Door shrouds give a finished look to door frames. NOTE: EP1 & EP2 Panels and components are available in legacy colors only.

19 Generation 1 Door Panels and shrouds description type w d h pattern no. list price 48 ADA door panel LH laminate door EP1DL48L $2,287. n/a $50. RH laminate door EP1DL48R 2,287. n/a 50. add for P2 add for P3 Panels, Connections, Power and Accessories Door shrouds LH corner door shroud EP1SDOL 11. n/a 0. LH straight door shroud EP1SDSL 11. n/a 0. RH corner door shroud EP1SDOR 11. n/a 0. RH straight door shroud EP1SDSR 11. n/a 0. Door master key Master key EP1DMK 20. n/a n/a Example: EP1DL42L, 117, 117, 117, 117 EP1DL Steel door panel 42 Width L Left handed 117 Soft Grey Front finish 117 Soft Grey Back finish 117 Soft Grey edgeband 117 Soft Grey trim Specify one surface and/or trim color, as appropriate. The direction the door pivots away from you determines the hand. Post and post connectors must be ordered separately. The door frame requires perpendicular support on the hinged side when the door is in an open position. 19 Two doors may not be placed back to back while sharing a single post connection. Doors in this application will not be properly supported and therefore no shroud exists to cover a back-to-back base opening. All 42 and 48 wide doors provide a minimum opening clearance of 32 and are compliant with the Americans with Disabilities Act. The 36 door opening is less than 32 and is not ADA compliant. All doors come with locking lever handset. Handset is ADA compliant. An adaptor cup is included to connect the door to adjoining panels. Door shrouds give a finished look to door frames. NOTE: EP1 & EP2 Panels and components are available in legacy colors only.

20 Generation 1 wall starter and wall mount channel description w d h * actual height pattern no. P1 P2 P3 Panel wall starter 1 1 /2 1 / EP1PWS28 $30. n/a $ /2 1 / EP1PWS n/a /2 1 / EP1PWS n/a /2 1 / EP1PWS n/a /2 1 / EP1PWS n/a /2 1 / EP1PWS n/a /2 1 / EP1PWS n/a 45. Wall mount channel 2 7 /8 3 / EP1WMC n/a /8 3 / EP1WMC n/a /8 3 / EP1WMC n/a /8 3 / EP1WMC n/a /8 3 / EP1WMC n/a /8 3 / EP1WMC n/a /8 3 / EP1WMC n/a /8 3 / EP1WMC n/a 185. * - actual height Example: EP1PWS60, 117 EP1PWS Panel wall starter 60 Height 117 Soft Grey trim Specify trim color. NOTE: Knoll, Inc. assumes no responsibility for wall construction or performance of fasteners used. Wall starter: Used to start a run of panels by fastening to an existing wall and attaching a connector assembly to it. Creates 11 /4 space from face of wall to centerline of post. Constructed of steel. The wall starter includes panel top and bottom hooks and modified post connector. Fasteners not included to attach to wall. Post and shrouds must be ordered separately. Wall mount channel: Allows hanging of all components and accessories on reinforced building walls. Painted extruded aluminum with a plastic inset which snaps in place, covering mounting screws. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 20

21 Generation 1 end panel and access panel description type application w h pattern no. list price grade End Panel Fabric 28 high 16 3 /4 28 EP1EPF28R $248. $255. $267. $272. $280. $285. $290. $297. n/a $ high 16 3 /4 40 EP1EPF40R n/a high 16 3 /4 48 EP1EPF48R n/a high 16 3 /4 53 EP1EPF53R n/a high 16 3 /4 60 EP1EPF60R n/a high 16 3 /4 65 EP1EPF65R n/a high 16 3 /4 80 EP1EPF80R n/a 50. add for P2 add for P3 Panels, Connections, Power and Accessories Steel 28 high 16 3 /4 28 EP1EPS28Re 180. n/a high 16 3 /4 40 EP1EPS40Re 180. n/a high 16 3 /4 48 EP1EPS48Re 189. n/a high 16 3 /4 53 EP1EPS53Re 197. n/a high 16 3 /4 60 EP1EPS60Re 205. n/a high 16 3 /4 65 EP1EPS65Re 210. n/a high 16 3 /4 80 EP1EPS80Re 265. n/a 50. Access Panel 40 high EP1BA2440Re ,015. 1,033. 1,050. 1,077. n/a EP1BA3040Re 1,031. 1,062. 1,113. 1,134. 1,165. 1,186. 1,206. 1,238. n/a EP1BA3640Re 1,031. 1,062. 1,113. 1,134. 1,165. 1,186. 1,206. 1,238. n/a EP1BA4840Re 1,300. 1,340. 1,404. 1,430. 1,468. 1,494. 1,520. 1,560. n/a high EP1BA2448Re ,019. 1,046. 1,064. 1,084. 1,111. n/a EP1BA3048Re 1,063. 1,094. 1,148. 1,169. 1,201. 1,222. 1,244. 1,276. n/a EP1BA3648Re 1,063. 1,094. 1,148. 1,169. 1,201. 1,222. 1,244. 1,276. n/a EP1BA4848Re 1,342. 1,381. 1,449. 1,476. 1,515. 1,542. 1,569. 1,610. n/a high EP1BA2453Re ,032. 1,050. 1,080. 1,098. 1,117. 1,146. n/a EP1BA3053Re 1,094. 1,127. 1,182. 1,204. 1,238. 1,259. 1,280. 1,314. n/a EP1BA3653Re 1,094. 1,127. 1,182. 1,204. 1,238. 1,259. 1,280. 1,314. n/a EP1BA4853Re 1,383. 1,425. 1,493. 1,522. 1,563. 1,591. 1,618. 1,660. n/a high EP1BA2460Re 1,016. 1,046. 1,097. 1,117. 1,147. 1,168. 1,189. 1,219. n/a EP1BA3060Re 1,163. 1,197. 1,255. 1,279. 1,315. 1,336. 1,360. 1,396. n/a EP1BA3660Re 1,163. 1,197. 1,255. 1,279. 1,315. 1,336. 1,360. 1,396. n/a EP1BA4860Re 1,470. 1,514. 1,588. 1,617. 1,661. 1,691. 1,720. 1,764. n/a 50. Example: EP1EPF60R, W812-9, 613 EP1 Generation 1 EPF End Panel, Fabric 60 Height R Raceway W812-9 Newbury-Malchite fabric 613 Silver trim Specify fabric when applicable and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. When ordering two different fabrics for the end panel, specify the left side first, then the right side. Hand is determined by facing the finished end of the panel. Topcaps and base raceway covers are included with panel. Posts and post connectors must be ordered separately. NOTE: P2 trim colors are not available on EP1 or EP2 panels and panel components. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. End panels have an integral glide on the finished end for leveling. End panel raceway is solid: electrical or cable management is not possible. Access panel incorporates a fabric privacy screen from the top of the panel to 25 above floor level. The bottom of the panel is left open for air flow utility access. 21

22 Generation 1 end panel and access panel description type application w h pattern no. list price grade Access Panel 65 high EP1BA2465Re $1,016. $1,046. $1,097. $1,117. $1,147. $1,168. $1,189. $1,219. n/a $ EP1BA3065Re 1,090. 1,123. 1,178. 1,199. 1,232. 1,253. 1,275. 1,308. n/a EP1BA3665Re 1,163. 1,197. 1,255. 1,279. 1,315. 1,336. 1,360. 1,396. n/a EP1BA4865Re 1,470. 1,514. 1,588. 1,617. 1,661. 1,691. 1,720. 1,764. n/a 50. add for P2 add for P3 80 high EP1BA2480Re 1,686. 1,737. 1,821. 1,855. 1,905. 1,940. 1,973. 2,024. n/a EP1BA3680Re 1,914. 1,971. 2,066. 2,105. 2,162. 2,200. 2,239. 2,296. n/a EP1BA4880Re 2,507. 2,583. 2,707. 2,758. 2,833. 2,884. 2,933. 3,009. n/a 50. Example: EP1EPF60R, W812-9, 613 EP1 Generation 1 EPF End Panel, Fabric 60 Height R Raceway W812-9 Newbury-Malchite fabric 613 Silver trim Specify fabric when applicable and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. When ordering two different fabrics for the end panel, specify the left side first, then the right side. Hand is determined by facing the finished end of the panel. Topcaps and base raceway covers are included with panel. Posts and post connectors must be ordered separately. NOTE: P2 trim colors are not available on EP1 or EP2 panels and panel components. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. End panels have an integral glide on the finished end for leveling. End panel raceway is solid: electrical or cable management is not possible. Access panel incorporates a fabric privacy screen from the top of the panel to 25 above floor level. The bottom of the panel is left open for air flow utility access. 22

23 Generation 1 single height post assemblies straight, corner and end description w d h pattern no. P1 P2 P3 Straight 28 EP1P28S $100. n/a $ EP1P40S 101. n/a EP1P48S 102. n/a EP1P53S 104. n/a EP1P60S 105. n/a EP1P65S 106. n/a EP1P80S 108. n/a 119. Panels, Connections, Power and Accessories Corner (90 ) 28 EP1P28L 96. n/a EP1P40L 97. n/a EP1P48L 98. n/a EP1P53L 100. n/a EP1P60L 101. n/a EP1P65L 102. n/a EP1P80L 105. n/a 115. End 28 EP1P28E 106. n/a EP1P40E 107. n/a EP1P48E 108. n/a EP1P53E 109. n/a EP1P60E 110. n/a EP1P65E 111. n/a EP1P80E 113. n/a 126. Example: EP1P48S, 117 EP1P Post 48 Height S Straight assembly 117 Soft Grey trim Specify trim color. Specify fabric color (if post covers are specified). Used to connect panels of the same height. Kit includes single height post, post plug, post connector and base raceway shroud(s) appropriate for the geometry specified. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. Fabric Post Covers are included (with appropriate post cap and base shroud) by adding a K suffix to the catalog number: -Straight assembly add $70., includes two straight fabric post covers. To specify two different fabrics, not both fabrics. -Corner, end, and 3-way T add $35., includes one corner, end or straight fabric post cover. -3-way Y and 4-way X do not have post cover kits. Bottom levelers on post allow for up to 1 1 /2 vertical adjustment. 23

24 Generation 1 single height post assemblies three and four way description w d h pattern no. P1 P2 P3 Three way ( T ) 28 EP1P28T $96. n/a $ EP1P40T 97. n/a EP1P48T 98. n/a EP1P53T 100. n/a EP1P60T 101. n/a EP1P65T 102. n/a EP1P80T 105. n/a 115. Three way ( Y ) 28 EP1P28Y 121. n/a EP1P40Y 123. n/a EP1P48Y 124. n/a EP1P53Y 125. n/a EP1P60Y 126. n/a EP1P65Y 128. n/a EP1P80Y 130. n/a 140. Four way ( X ) 28 EP1P28X 84. n/a EP1P40X 85. n/a EP1P48X 86. n/a EP1P53X 87. n/a EP1P60X 88. n/a EP1P65X 89. n/a EP1P80X 92. n/a 101. Secification Information Example: EP1P80T, 117 EP1P Post 80 Height T T assembly 117 Soft Grey trim Specify trim color. Specify fabric color (if post covers are specified). Used to connect panels of the same height. Kit includes single height post, post plug, post connector and base raceway shroud(s) appropriate for the geometry specified. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. Fabric Post Covers are included (with appropriate post cap and base shroud) by adding a K suffix to the catalog number: -Straight assembly add $70., includes two straight fabric post covers. To specify two different fabrics, not both fabrics. -Corner, end, and 3-way T add $35., includes one corner, end or straight fabric post cover. -3-way Y and 4-way X do not have post cover kits. Bottom levelers on post allow for up to 1 1 /2 vertical adjustment. 24

25 Generation 1 dual height posts description w d h pattern no. P1 P2 P3 Dual height post 28 /40 EP1DP2840 $104. n/a $ /48 EP1DP n/a /53 EP1DP n/a /60 EP1DP n/a /65 EP1DP n/a /80 EP1DP n/a /48 EP1DP n/a /53 EP1DP n/a /60 EP1DP n/a /65 EP1DP n/a /80 EP1DP n/a /53 EP1DP n/a /60 EP1DP n/a /65 EP1DP n/a /80 EP1DP n/a /60 EP1DP n/a /65 EP1DP n/a /80 EP1DP n/a /65 EP1DP n/a /80 EP1DP n/a /80 EP1DP n/a 144. Panels, Connections, Power and Accessories Example: EP1DP4860, 613 EP1DP Dual height post 48 Height one 60 Height two 613 Silver Specify trim color. Dual height posts are used where panels of two different heights intersect. Bottom levelers on posts allow for up to 11 /2 vertical adjustment. Due to the variety of combinations possible, connector caps, shrouds and post covers must all be ordered separately. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 25

26 Generation 1 triple height posts description w d h pattern no. P1 P2 P3 Triple height post 28 /40 /48 EP1TP $131. n/a $ /40 /53 EP1TP n/a /40 /60 EP1TP n/a /40 /65 EP1TP n/a /40 /80 EP1TP n/a /48 /53 EP1TP n/a /48 /60 EP1TP n/a /48 /65 EP1TP n/a /48 /80 EP1TP n/a /53 /60 EP1TP n/a /53 /65 EP1TP n/a /53 /80 EP1TP n/a /60 /65 EP1TP n/a /60 /80 EP1TP n/a /65 /80 EP1TP n/a /48 /53 EP1TP n/a /48 /60 EP1TP n/a /48 /65 EP1TP n/a /48 /80 EP1TP n/a /53 /60 EP1TP n/a /53 /65 EP1TP n/a /53 /80 EP1TP n/a /60 /65 EP1TP n/a /60 /80 EP1TP n/a /65 /80 EP1TP n/a /53 /60 EP1TP n/a /53 /65 EP1TP n/a /53 /80 EP1TP n/a /60 /65 EP1TP n/a /60 /80 EP1TP n/a /65 /80 EP1TP n/a /60 /65 EP1TP n/a /60 /80 EP1TP n/a /65 /80 EP1TP n/a /65 /80 EP1TP n/a 170. Example: EP1TP406080, 113 EP1TP Triple height post 40 Height one 60 Height two 80 Height three 113 Dary Grey trim Specify trim color. Triple height posts are used where 3 or 4 panels of three different heights intersect. Bottom levelers on posts allow for up to 11 /2 vertical adjustment. Due to the variety of combinations possible, connector caps, shrouds and post covers must all be ordered separately. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 26

27 Generation 1 single height posts description w d h pattern no. P1 P2 P3 Single height post 28 EP1P28 $48. n/a $ EP1P n/a EP1P n/a EP1P n/a EP1P n/a EP1P n/a EP1P n/a 60. Panels, Connections, Power and Accessories Example: EP1P48, 117 EP1P Post 48 Height 117 Soft Grey trim Specify trim color. Post connectors and shrouds must be order separately. Bottom leveler on posts allow for up to 11 /2 of vertical adjustment. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 27

28 Generation 1 post connectors and shrouds description type pattern no. P1 P2 P3 Post connectors End with post EP1PCEP $24. $25. $26. End with post (for post covers) EP1PCEPK Four-way X EP1PCX Multi-height filler EP1PCMF Post plug (pkg. of 25) EP1PLUG Straight EP1PCS Three-way T EP1PCT Three-way Y 120 EP1PCY Trim filler EP1PCTF Two-way L EP1PCL Two-way L (for post covers) EP1PCLK Two-way adjustable angle EP1PCA Raceway shroud End with post EP1SEP 34. n/a 38. End with post (for post covers) EP1SEPK 34. n/a 38. Inside 120 EP1SI n/a 16. Outside L EP1SL 24. n/a 26. Outside L (for post covers) EP1SLK 24. n/a 26. Outside 120 EP1SO n/a 21. Outside 135 EP1SO n/a 21. Straight EP1SS 18. n/a 20. Example: EP1SEP EP1S Post shroud EP End with post Specify post connector and shroud trim color. Specify one multi height filler (EP1PCMF) for each low panel in a multi height connection. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. Exception: EP1 posts connectors only are available in all colors as they may need to be specified when ordering stack-on panels with an EP3 profile. 28 Post connectors stabilize panel to panel connections. Post connectors have painted finish and a quick mount design. Mounting screws are included. Conical connector screw is included with post. One Post Plug (OPPC) is included with every connector cap ordered. If additional post plugs are required a bag of 25 may be purchased separately. The EP1PCTF is a trim filler piece that is to be used when no other post part can be used in a given panel layout. This piece butts against EP1PCS and EP1PCT, when installed as an addition. Shrouds provide a finished raceway cover at posts. Two-way L connections do not require an inside shroud.

29 Generation 1 post covers - straight description type application w d h pattern no. grade Straight post cover Fabric 28 EP1FPC28S $40. $42. $44. $45. $46. $47. $47. $ EP1FPC40S EP1FPC48S EP1FPC53S EP1FPC60S EP1FPC65S EP1FPC80S Panels, Connections, Power and Accessories Multi height post cover Fabric 28/65 37 EP1FPCM37S /80 52 EP1FPCM52S /53 13 EP1FPCM13S /60 20 EP1FPCM20S /65 25 EP1FPCM25S /80 40 EP1FPCM40S /49 8 EP1FPCM8S /60 12 EP1FPCM12S /65 17 EP1FPCM17S /80 32 EP1FPCM32S /60 7 EP1FPCM7S /80 27 EP1FPCM27S /65 5 EP1FPCM5S /80 15 EP1FPCM15S Example: EP1FPC60S, W809-1 EP1FPC Post cover, fabric 60 Height S Straight W809-1 Devon Granite fabric Specify fabric color. Note: When using post covers be sure to specify post connectors and shrouds designated for post cover configurations. Straight covers are of fabric covered steel construction and are used to cover posts between straight panel runs. 29

30 Generation 1 post covers - outside 90 and end description type w d h pattern no. grade Outside 90 post cover Fabric 28 EP1FPC28L $42. $43. $45. $46. $47. $48. $48. $ EP1FPC40L EP1FPC48L EP1FPC53L EP1FPC60L EP1FPC65L EP1FPC80L End post cover Fabric 28 EP1FPC28EP EP1FPC40EP EP1FPC48EP EP1FPC53EP EP1FPC60EP EP1FPC65EP EP1FPC80EP Example: EP1FPC60L, W281-9 EP1FPC Post cover, fabric 60 Height L Two-way L W281-9 Clarity Black Tie fabric Specify fabric color. Note: When using post covers be sure to specify post connectors and shrouds designated for post cover configurations. Two-way L and end covers are of fabric covered steel construction and are used to cover posts on an end of panel run or for the outside of a two-way connection. 30

31 Generation 1 panel extender kit description type w d h pattern no. P1 P2 P3 Raceway panel extender kit 36 wide EP1PE3640R $237. n/a $ EP1PE3648R 264. n/a EP1PE3653R 285. n/a EP1PE3660R 304. n/a EP1PE3665R 321. n/a EP1PE3680R 371. n/a 52. Panels, Connections, Power and Accessories 48 wide EP1PE4840R 246. n/a EP1PE4848R 274. n/a EP1PE4853R 293. n/a EP1PE4860R 315. n/a EP1PE4865R 330. n/a EP1PE4880R 382. n/a wide EP1PE6040R 260. n/a EP1PE6048R 285. n/a EP1PE6053R 305. n/a EP1PE6060R 326. n/a EP1PE6065R 341. n/a EP1PE6080R 393. n/a 52. Example: EP1PE6065R, 117 EP1PE Raceway panel extender kit 60 Width in inches 65 Height R Raceway 117 Soft Grey trim Specify trim color. Jumpers to carry power through panel are ordered separately. With panel extender kits, add 3 to jumper length for each panel extender kit used. A kit designed to be field mounted onto panels to extend the width of the panel by 3 ( 11 /2 on each side). This adaption of the panel(s) will allow clearance when positioning existing freestanding equipment, i.e., files and desks, between side panels. 31 Kit contains two aluminum side extrusions, an extended top cap, extended baseboard covers, an extended communication boot, installation hardware and instructions. NOTE: EP1 & EP2 Panels and components are available in legacy colors only.

32 Generation 3 Fabric panel 29 thru 54 high description type w h pattern no. grade Fabric panel 29 high EP3FA1229(K/N) $440. $453. $476. $485. $497. $506. $515. $528. $25. $ EP3FA1829(K/N) EP3FA2429(K/N) EP3FA3029(K/N) EP3FA3629(K/N) EP3FA4229(K/N) EP3FA4829(K/N) EP3FA6029(K/N) add for P2 add for P3 41 high EP3FA1241(K/N) EP3FA1841(K/N) EP3FA2441(K/N) EP3FA3041(K/N) EP3FA3641(K/N) EP3FA4241(K/N) EP3FA4841(K/N) EP3FA6041(K/N) high EP3FA1249(K/N) EP3FA1849(K/N) EP3FA2449(K/N) EP3FA3049(K/N) EP3FA3649(K/N) EP3FA4249(K/N) EP3FA4849(K/N) EP3FA6049(K/N) high EP3FA1254(K/N) EP3FA1854(K/N) EP3FA2454(K/N) EP3FA3054(K/N) EP3FA3654(K/N) EP3FA4254(K/N) EP3FA4854(K/N) EP3FA6054(K/N) Specification Informantion Example: EP3FA3649N, S812, 117 EP3FA Fabric panel 36 Width 49 Height N No Knockouts S812 Saxony Plus Opal fabric 117 Soft Grey trim Specify fabric and trim color. Note: Power duplexes cannot be installed on 12 W panels. Side mount receptacles available in 24 W panels and wider while using E series power. Electrical components must be ordered separately. Specify K on the end of the pattern number for raceway covers with knockout N for raceway covers without Knockouts. Panel is fabric covered. If two different fabrics are used on one panel, price will reflect cost of the more expensive panel fabric. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components. 32

33 Generation 3 Fabric panel 61 thru 81 high description type w h pattern no. grade Fabric panel 61 high EP3FA1261(K/N) $498. $514. $539. $548. $564. $573. $583. $598. $25. $ EP3FA1861(K/N) EP3FA2461(K/N) EP3FA3061(K/N) EP3FA3661(K/N) EP3FA4261(K/N) EP3FA4861(K/N) EP3FA6061(K/N) ,011. 1,029. 1, add for P2 add for P3 Panels, Connections, Power and Accessories 64 high EP3FA1264(K/N) EP3FA1864(K/N) EP3FA2464(K/N) EP3FA3064(K/N) EP3FA3664(K/N) EP3FA4264(K/N) EP3FA4864(K/N) EP3FA6064(K/N) high EP3FA1281(K/N) EP3FA1881(K/N) EP3FA2481(K/N) EP3FA3081(K/N) EP3FA3681(K/N) EP3FA4281(K/N) , EP3FA4881(K/N) ,000. 1,028. 1,046. 1,064. 1, EP3FA6081(K/N) 1,061. 1,092. 1,145. 1,167. 1,199. 1,220. 1,242. 1, Example: EP3FA2461K, W351-3, 117 EP3FA Fabric panel 24 Width 61 Height K Knockouts W351-3 Foundation, Cornsilk 117 Soft Grey trim Specify fabric and trim color. Post assemblies or connection elements must be ordered separately. Note: Power duplexes cannot be installed on 12 W panels. Side mount receptacles available in 24 W panels and wider while using E series power. Specify K on the end of pattern number for raceway covers with knockout N for raceway covers without knockouts. Electrical components must be ordered separately. 33 Panel is fabric covered. If two different fabrics are used on one panel, price will reflect cost of the more expensive panel fabric. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components.

34 Generation 3 Insert panel description type w d h pattern number open frame OF plexiglas PG* perforated steel PS marker board MB polycarbonate PY* add for P2 finishes add for P3 finishes Insert panel 29 high EP3( )1229(K/N) $469. $630. $593. $593. $547. $25. $ EP3( )1829(K/N) EP3( )2429(K/N) EP3( )3029(K/N) EP3( )3629(K/N) EP3( )4229(K/N) EP3( )4829(K/N) EP3( )6029(K/N) high EP3( )1241(K/N) EP3( )1841(K/N) EP3( )2441(K/N) EP3( )3041(K/N) EP3( )3641(K/N) EP3( )4241(K/N) EP3( )4841(K/N) EP3( )6041(K/N) ,098. 1,006. 1, high EP3( )1249(K/N) EP3( )1849(K/N) EP3( )2449(K/N) EP3( )3049(K/N) EP3( )3649(K/N) EP3( )4249(K/N) , EP3( )4849(K/N) , EP3( )6049(K/N) ,226. 1,098. 1,098. 1, high EP3( )1254(K/N) EP3( )1854(K/N) EP3( )2454(K/N) EP3( )3054(K/N) EP3( )3654(K/N) ,073. 1, EP3( )4254(K/N) ,108. 1,108. 1, EP3( )4854(K/N) ,123. 1,132. 1, EP3( )6054(K/N) ,247. 1,164. 1,164. 1, high EP3( )1261(K/N) EP3( )1861(K/N) EP3( )2461(K/N) EP3( )3061(K/N) , * All Colors Example: EP3PY3649K, PC, 613 EP3PY Polycarbonate Insert Panel 36 Width 49 Height K Knockouts PC Polycarbonate Clear 613 Silver trim Specify insert type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Topcaps and base raceway covers are included with panels. Posts and post connectors must be ordered separately. 34

35 Generation 3 Insert panel description type w d h pattern number open frame OF plexiglas PG* perforated steel PS marker board MB polycarbonate PY* add for P2 finishes add for P3 finishes Insert panel 61 high EP3( )3661(K/N) $568. $1,035. $1,141. $1,141. $950. $25. $ EP3( )4261(K/N) ,130. 1,177. 1, EP3( )4861(K/N) ,222. 1,202. 1, EP3( )6061(K/N) ,370. 1,245. 1,245. 1, Panels, Connections, Power and Accessories 64 high EP3( )1264(K/N) EP3( )1864(K/N) EP3( )2464(K/N) EP3( )3064(K/N) , EP3( )3664(K/N) ,046. 1,040. 1, EP3( )4264(K/N) ,141. 1,121. 1, EP3( )4864(K/N) ,397. 1,182. 1, EP3( )6064(K/N) ,423. 1,414. 1,414. 1, high EP3( )1281(K/N) EP3( )1881(K/N) EP3( )2481(K/N) ,060. 1,046. 1, EP3( )3081(K/N) ,228. 1,076. 1, EP3( )3681(K/N) ,334. 1,316. 1, EP3( )4281(K/N) ,538. 1,346. 1,346. 1, EP3( )4881(K/N) ,552. 1,491. 1,491. 1, EP3( )6081(K/N) ,767. 1,540. 1,540. 1, * All Colors Example: EP3PY3649K, PC, 613 EP3PY Polycarbonate Insert Panel 36 Width 49 Height K Knockouts PC Polycarbonate Clear 613 Silver trim Specify insert type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Topcaps and base raceway covers are included with panels. Posts and post connectors must be ordered separately. 35

36 Generation 3 Door Panels and shrouds description type w d h pattern no. list price 36 Door panel LH laminate door EP3DL36L $1,426. $25. $50. RH laminate door EP3DL36R 1, add for P2 add for P3 42 ADA door panel LH laminate door EP3DL42L 1, RH laminate door EP3DL42R 1, Example: EP3DL42L, 117, 117, 117, 117 EP3DL Steel door panel 42 Width L Left handed 117 Soft Grey front finish 117 Soft Grey back finish 117 Soft Grey edgeband 117 Soft Grey trim Specify one surface and/or trim color, as appropriate. The direction the door pivots away from you determines the hand. Post and post connectors must be ordered separately. The door frame requires perpendicular support on the hinged side when the door is in an open position. 36 Two doors may not be placed back to back while sharing a single post connection. Doors in this application will not be properly supported and therefore no shroud exists to cover a back-to-back base opening. All 42 and 48 wide doors provide a minimum opening clearance of 32 and are compliant with the Americans with Disabilities Act. The 36 door opening is less than 32 and is not ADA compliant. All doors come with locking lever handset. Handset is ADA compliant. An adaptor cup is included to connect the door to adjoining panels. Door shrouds give a finished look to door frames.

37 Generation 3 Door Panels and shrouds description type w d h pattern no. list price 48 ADA door panel LH laminate door EP3DL48L $2,287. $25. $50. RH laminate door EP3DL48R 2, add for P2 add for P3 Panels, Connections, Power and Accessories Door shrouds LH corner door shroud EP3SDOL LH straight door shroud EP3SDSL RH corner door shroud EP3SDOR RH straight door shroud EP3SDSR Door master key Master key EP1DMK 20. n/a n/a Example: EP3DL42L, 117, 117, 117, 117 EP3DL Steel door panel 42 Width L Left handed 117 Soft Grey front finish 117 Soft Grey back finish 117 Soft Grey edgeband 117 Soft Grey trim Specify one surface and/or trim color, as appropriate. The direction the door pivots away from you determines the hand. Post and post connectors must be ordered separately. The door frame requires perpendicular support on the hinged side when the door is in an open position. 37 Two doors may not be placed back to back while sharing a single post connection. Doors in this application will not be properly supported and therefore no shroud exists to cover a back-to-back base opening. All 42 and 48 wide doors provide a minimum opening clearance of 32 and are compliant with the Americans with Disabilities Act. The 36 door opening is less than 32 and is not ADA compliant. All doors come with locking lever handset. Handset is ADA compliant. An adaptor cup is included to connect the door to adjoining panels. Door shrouds give a finished look to door frames.

38 Generation 3 Wall starter and wall mount channel description w d h actual height pattern no. P1 P2 P3 Panel wall starter 1 1 /2 1 / EP3PWS29 $30. $31. $ /2 1 / EP3PWS /2 1 / EP3PWS /2 1 / EP3PWS /2 1 / EP3PWS /2 1 / EP3PWS /2 1 / EP3PWS Wall mount channel 2 7 /8 3 / EP3WMC /8 3 / EP3WMC /8 3 / EP3WMC /8 3 / EP3WMC /8 3 / EP3WMC /8 3 / EP3WMC /8 3 / EP3WMC /8 3 / EP3WMC Example: EP3PWS61, 117 EP3PWS Panel wall starter Height 117 Soft Grey trim Specify trim color Note: Knoll, Inc. assumes no responsibility for wall construction of performance of fasteners used. Wall starter: Used to start a run of panels by fastening to an existing wall and attaching a connector assembly to it. Creates 1 1 /4 space from face to wall to centerline of post. Constructed of steel. The wall starter includes panel top and bottom hook and modified post connector. Fasteners not included to attach to wall. Post and shrouds must be ordered separately. Wall mount channel: Allows hanging of all components and accessories on reinforced building walls. Painted extruded aluminum with a plastic inset which snaps in place, covering mounting screws. 38

39 Generation 3 Single-height post assemblies straight, 2 way L, 2 way 120 and 3 way T description w d h pattern no. P1 P2 P3 Straight 29 EP3P29S $100. $105. $ EP3P41S EP3P49S EP3P54S EP3P61S EP3P64S EP3P81S Panels, Connections, Power and Accessories 2 way L 29 EP3P29L EP3P41L EP3P49L EP3P54L EP3P61L EP3P64L EP3P81L Example: EP3P64S, 117 EP3P Generation 3 post 64 Height S Straight assembly 117 Soft Grey trim Specify trim color Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Used to connect panels of the same height. Assembly includes single height post, post connector, post connector plug and base raceway shroud appropriate for the configuration specified. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components. 39

40 Generation 3 Single-height post assemblies straight, 2 way L, 2 way 120 and 3 way T description w d h pattern no. P1 P2 P3 2-way EP3P29120 $100. $105. $ EP3P EP3P EP3P EP3P EP3P EP3P way T 29 EP3P29T EP3P41T EP3P49T EP3P54T EP3P61T EP3P64T EP3P81T Example: EP3P64S, 117 EP3P Generation 3 post 64 Height S Straight assembly 117 Soft Grey trim Specify trim color Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Used to connect panels of the same height. Assembly includes single height post, post connector, post connector plug and base raceway shroud appropriate for the configuration specified. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components. 40

41 Generation 3 Single-height post assemblies 3 way 120, 4 way X, end with post and postless end kit description w d h pattern no. P1 P2 P3 3-Way EP3P29Y $121. $128. $ EP3P41Y EP3P49Y EP3P54Y EP3P61Y EP3P64Y EP3P81Y Panels, Connections, Power and Accessories 4-way X 29 EP3P29X EP3P41X EP3P49X EP3P54X EP3P61X EP3P64X EP3P81X Example: EP3P64X, 117 EP3P Generation 3 post 64 Height X 4-way X assembly 117 Soft Grey trim Specify trim color Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Used to connect panels of the same height. Assembly includes single height post, post connector, post connector plug and base raceway shroud appropriate for the configuration specified. Postless end kit should not be used on panels that are places perpendicular to a worksurface of the same depth as the front of the worksurface will extend beyond the panel end. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components. 41

42 Generation 3 Single-height post assemblies 3 way 120, 4 way X, end with post and postless end kit description w d h pattern no. P1 P2 P3 End with post 29 EP3P29E $106. $111. $ EP3P41E EP3P49E EP3P54E EP3P61E EP3P64E EP3P81E Postless End Kit 29 EP3ETK EP3ETK EP3ETK EP3ETK EP3ETK EP3ETK EP3ETK Example: EP3P64X, 117 EP3P Generation 3 post 64 Height X 4-way X assembly 117 Soft Grey trim Specify trim color Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Used to connect panels of the same height. Assembly includes single height post, post connector, post connector plug and base raceway shroud appropriate for the configuration specified. Postless end kit should not be used on panels that are places perpendicular to a worksurface of the same depth as the front of the worksurface will extend beyond the panel end. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components. 42

43 Generation 3 Dual height posts description w d h pattern no. P1 P2 P3 Dual height post 29 /41 EP3DP2941 $104. $109. $ /49 EP3DP /54 EP3DP /61 EP3DP /64 EP3DP /81 EP3DP /49 EP3DP /54 EP3DP /61 EP3DP /64 EP3DP /81 EP3DP /54 EP3DP /61 EP3DP /64 EP3DP /81 EP3DP /61 EP3DP /64 EP3DP /81 EP3DP /64 EP3DP /81 EP3DP /81 EP3DP Panels, Connections, Power and Accessories Example: EP3DP4964, 117 EP3DP Dual height post /64 Height 117 Soft Grey trim Specify trim color 43 Dual height posts are used where panels of two different heights intersect. Bottom leveler on post allows for up to 1 1 /2 of vertical adjustment. Due to the variety of combinations possible, post connectors and shrouds must be ordered separately. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components.

44 Generation 3 Triple height posts description w d h pattern no. P1 P2 P3 Triple height post 29 /41 /49 EP3TP $131. $137. $ /41 /54 EP3TP /41 /61 EP3TP /41 /64 EP3TP /41 /81 EP3TP /49 /54 EP3TP /49 /61 EP3TP /49 /64 EP3TP /49 /81 EP3TP /54 /61 EP3TP /54 /64 EP3TP /54 /81 EP3TP /61 /64 EP3TP /61 /81 EP3TP /64 /81 EP3TP /49 /54 EP3TP /49 /61 EP3TP /49 /64 EP3TP /49 /81 EP3TP /54 /61 EP3TP /54 /64 EP3TP /54 /81 EP3TP /61 /64 EP3TP /61 /81 EP3TP /64 /81 EP3TP /54 /61 EP3TP /54 /64 EP3TP /54 /81 EP3TP /61 /64 EP3TP /61 /81 EP3TP /64 /81 EP3TP /61 /64 EP3TP /61 /81 EP3TP /64 /81 EP3TP /64 /81 EP3TP Example: EP3TP496481, 113 EP3TP Triple height post /64/81 Heights 113 Dark Grey trim Specify trim color 44 Triple height posts are used where 3 or 4 panels of three different heights intersect. Bottom leveler on post allows for up to 1 1 /2 of vertical adjustment. Due to the variety of combinations possible, post connectors and shrouds must be ordered separately. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components.

45 Generation 3 Single height post description w d h pattern no. P1 P2 P3 Single height post 29 EP3P29 $48. $50. $ EP3P EP3P EP3P EP3P EP3P EP3P Panels, Connections, Power and Accessories Example: EP3P49, 117 EP3P Post 49 Height 117 Soft Grey trim Specify trim color Post connectors and shrouds must be ordered separately. 45 Bottom leveler on post allows for up to 1 1 /2 of vertical adjustment. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components.

46 Generation 3 post connectors, and shrouds description type pattern no. P1 P2 P3 Post connectors 2-way 120 EP3PC120 $22. $23. $24. 2-way, L EP3PCL way, L (for post covers) EP3PCLK way Y 120 EP3PCY way, T EP3PCT way, X EP3PCX end with post EP3PCEP end with post (for post covers) EP3PCEPK multi-height filler EP3PCMF straight connector EP3PCS Shrouds shroud, end w/post EP3SEP shroud, inside 120 EP3SI shroud, outside L EP3SL shroud, outside 120 EP3SO shroud, straight EP3SS Example: EP3PCL, 613 EP3 Generation 3 PC Post connector L 2-way L 613 Silver trim Specify trim color. Specify one multi-height post connector (EP3PCMF) for each low panel in a multi-height connection. Generation 3 panels are not compatible with Generation 1 or Generation 2 panels or panel components. 46

47 Generation 3 post covers - straight description type application w d h pattern no. grade Straight post cover Fabric 29 EP3FPC29S $40. $42. $44. $45. $46. $47. $47. $ EP3FPC41S EP3FPC49S EP3FPC54S EP3FPC61S EP3FPC81S Panels, Connections, Power and Accessories Multi height post cover Fabric 29/64 35 EP3FPCM35S /81 52 EP3FPCM52S /49 8 EP3FPCM8S /54 13 EP3FPCM13S /61 20 EP3FPCM20S /64 23 EP3FPCM23S /81 40 EP3FPCM40S /61 12 EP3FPCM12S /64 15 EP3FPCM15S /81 32 EP3FPCM32S /61 7 EP3FPCM7S /81 27 EP3FPCM27S /64 3 EP3FPCM3S /81 15 EP3FPCM15S Example: EP3FPC61S, W809-1 EP3FPC Post cover, fabric 61 Height S Straight W809-1 Devon Granite fabric Specify fabric color. Note: When using post covers be sure to specify post connectors and shrouds designated for post cover configurations. Straight covers are of fabric covered steel construction and are used to cover posts between straight panel runs. 47

48 Generation 3 post covers - outside 90 and end description type w d h pattern no. grade Outside 90 post cover Fabric 29 EP3FPC29L $42. $43. $45. $46. $47. $48. $48. $ EP3FPC41L EP3FPC49L EP3FPC54L EP3FPC61L EP3FPC81L End post cover Fabric 29 EP3FPC29EP EP3FPC41EP EP3FPC49EP EP3FPC54EP EP3FPC61EP EP3FPC81EP Example: EP3FPC61L, W281-9 EP3FPC Post cover, fabric 61 Height L Two-way L W281-9 Clarity Black Tie fabric Specify fabric color. Note: When using post covers be sure to specify post connectors and shrouds designated for post cover configurations. Two-way L and end covers are of fabric covered steel construction and are used to cover posts on an end of panel run or for the outside of a two-way connection. 48

49 Personal Flat Bi-Fold Door description type w d h pattern number Personal flat bi-fold door plexiglas PG* perforated steel PS marker board MB polycarbonate PY* lumasite LU add for P2 finishes add for P3 finishes 49 high EP4BD( )3649P(R/L) $1,965. $2,232. $2,232. $2,219. $2,303. $25. $ high EP4BD( )4249P(R/L) 2,159. 2,350. 2,350. 2,261. 2, high EP4BD( )4849P(R/L) 2,539. 2,472. 2,472. 2,307. 2, high EP4BD( )6049P(R/L) 2,568. 2,591. 2,591. 2,572. 2, high EP4BD( )3661P(R/L) 2,012. 2,270. 2,270. 2,288. 2, high EP4BD( )4261P(R/L) 2,212. 2,389. 2,389. 2,332. 2, high EP4BD( )4861P(R/L) 2,600. 2,513. 2,513. 2,378. 2, high EP4BD( )6061P(R/L) 2,631. 2,633. 2,633. 2,652. 2, high EP4BD( )3664P(R/L) 2,036. 2,297. 2,298. 2,315. 2, high EP4BD( )4264P(R/L) 2,239. 2,418. 2,418. 2,360. 2, high EP4BD( )4864P(R/L) 2,632. 2,534. 2,534. 2,415. 2, high EP4BD( )6064P(R/L) 2,662. 2,666. 2,666. 2,684. 2, high EP4BD( )3681P(R/L) 2,085. 2,352. 2,354. 2,372. 2, high EP4BD( )4281P(R/L) 2,293. 2,478. 2,477. 2,417. 2, high EP4BD( )4881P(R/L) 2,697. 2,596. 2,596. 2,473. 2, high EP4BD( )6081P(R/L) 2,727. 2,730. 2,730. 2,751. 2, Panels, Connections, Power and Accessories * All Colors Example: EP4BDPY3649PR, PC, 613 EP4BD Flat Bi-fold Door PY Polycarbonate 36 Width 49 Height P Personal door R Right Handed PC Clear Polycarbonate 613 Silver Paint Specify insert type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Bi-fold door connects to the end of an panel utilizing a postless end kit (ordered separately). Door section contains insert selction placed inside an extruded aluminum frame. Mid panel section is a solid steel component that is painted to match the trim finish. The channel section is screwed into the end of an panel with a postless end kit (ordered separately) using the included hardware. Please consult Custom Product Development if you wish to attach the door to other systems or a wall. When opened, the door folds flat against the panel it is attached to. Door may fold to either the inside or outside of a panel depending on the hand specified. 49

50 Add-on Screens description type w h pattern no. P1 P2 P3 Add-on screens polycarbonate EP3AOPY1215 $364. $381. $ EP3AOPY EP3AOPY EP3AOPY EP3AOPY EP3AOPY EP3AOPY EP3AOPY perforated steel EP3AOPS EP3AOPS EP3AOPS EP3AOPS EP3AOPS EP3AOPS EP3AOPS EP3AOPS plexiglass EP3AOPG EP3AOPG EP3AOPG EP3AOPG EP3AOPG EP3AOPG EP3AOPG EP3AOPG lumasite EP3AOLU EP3AOLU EP3AOLU EP3AOLU EP3AOLU EP3AOLU EP3AOLU EP3AOLU Example: EP3AOPY4815, PC, 117 EP3 panel AO Add-on PY Polycarbonate insert 4815 Width/Height PC Clear Polycarbonate 117 Soft Grey trim Specify insert color, if applicable and trim color. Add-on screens work with Generation one, two or three panels. Add-on screens mount on the slotted standard with (2) die cast stanchion brackets that are included. All attachment hardware is included. Two add-on screens may not be mounted next to each other on the inside corner of a 90 connection. 50

51 Components stack-on panels provide the flexibility to increase the overall of height of any standard panel. The stack-on panel is available in all standard widths and a variety of heights in both slotted and slotless versions. Stack-on panels with slots provide the capability to hang standard components such as shelves and overheads as long as the weight load does not exceed 3lbs. Per lineal inc. Stack-on panels without slots do not allow for hanging components, but do provide a cleaner aesthetic when specifying window applications. Up to two (2) stack-on panels may be stacked on top of a standard panel as long as the total height above the base panels is no taller than 40 and neither individual stack-on panel is taller than 20. Stack-on panel width must match the width of the panel it is stacking on. Stack-on panel connectors must be used between adjacent stack-on panels. Stack-On Panels Stacking on to EP1/EP2 Panels Specifying stack-on panels and connections is very similar to specifying a standard run of panels. Specify the appropriate stack-on panel based on the height required and the width of the panel it will be stacked on. Order a stack-on post to join adjacent stack-on panels as well as one for either end of the run. If you are connecting a stack-on panel to an existing hi/lo connection there is no need to order an additional stack-on post. Simply tie into the existing hi/lo post with the appropriate post connection hardware. The final step is to specify the appropriate post connectors (straight, corner, etc.) as dictated by the configuration on top of the stack-on panel. Note: Please make sure post connectors are ordered based on the configuration of the stack-on panels not the base panels as they may be different at the end of the run. Stacking On To EP3 Panels Stacking on top of an EP3 panel is quite different from that of an EP1 or EP2 panel as the topcap and post connector profiles are different. Note: Some stack-on configurations may not be possible when used in conjunction with EP3 panels and connectors. Verify that all components correspond with the appropriate generation topcap and/or post connector/ Follow the instructions listed previously for stacking on to an EP1/EP2 until you get to the final step. When ordering post connectors for stack-on panels it is important to remember that stack-on panels will only stack on top of EP1 post connectors to follow the configuration of the base panels and use EP3 connectors for the configuration of the stack-on panels. Note: It is easiest to order EP3 panels and post assemblies for the base panels before ordering the stack-on panels as the post connectors and top caps can simply be transferred to the top of the stack-on panels in most configurations. Panels, Connections, Power and Accessories Stack-on Post Connectors There are two types of stack-on post connectors; Standard - for use without post covers and extended - for use with post covers. Both provide a stable connection to the lower panel through the use of a double threaded screw. This screw is attached to the base post which then allows the stack-on post to screw to the top of the base post. Standard Extended 51

52 Stack-On Insert Panel with slots description w d h pattern no. plexiglas (ALL COLORS) PG perforated steel PS / Lumasite LU polycarbonate (ALL COLORS) PY add for P2 finishes add for P3 finishes 12 high EP2S( )1212 $486. $451. $422. $15. $ EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) high EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) high EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) high EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) Example: EP2SPS3615, 613 EP2S Stack-on panel PS Perforated Steel 36 Width 15 Height 613 Silver trim Specify insert type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. NOTE: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. 52 Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on posts and connectors must be ordered separately.

53 Stack-On Insert Panel with slots description w d h pattern no. plexiglas (ALL COLORS) PG perforated steel PS / Lumasite LU polycarbonate (ALL COLORS) PY add for P2 finishes add for P3 finishes 20 high EP2S( )1220 $551. $513. $479. $15. $ EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) EP2S( ) Panels, Connections, Power and Accessories Example: EP2SPS3615, 613 EP2S Stack-on panel PS Perforated Steel 36 Width 15 Height 613 Silver trim Specify insert type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. NOTE: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. 53 Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on posts and connectors must be ordered separately.

54 Stack-On Insert Panel without slots description w d h pattern no. plexiglas (ALL COLORS) PG perforated steel PS / Lumasite LU polycarbonate (ALL COLORS) PY add for P2 finishes add for P3 finishes 12 high EP2S( )1212N $486. $451. $422. $15. $ EP2S( )1812N EP2S( )2412N EP2S( )3012N EP2S( )3612N EP2S( )4212N EP2S( )4812N EP2S( )6012N high EP2S( )1213N EP2S( )1813N EP2S( )2413N EP2S( )3013N EP2S( )3613N EP2S( )4213N EP2S( )4813N EP2S( )6013N high EP2S( )1215N EP2S( )1815N EP2S( )2415N EP2S( )3015N EP2S( )3615N EP2S( )4215N EP2S( )4815N EP2S( )6015N high EP2S( )1217N EP2S( )1817N EP2S( )2417N EP2S( )3017N EP2S( )3617N EP2S( )4217N EP2S( )4817N EP2S( )6017N Example: EP2SPS3615N, 613 EP2S Stack-on panel PS Perforated Steel 36 Width 15 Height N No Slots 613 Silver trim Specify inserty type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. NOTE: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. 54 Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on panels without slots do not allow for hanging components. Stack-on posts and connectors must be ordered separately.

55 Stack-On Insert Panel without slots description w d h pattern no. plexiglas (ALL COLORS) PG perforated steel PS / Lumasite LU polycarbonate (ALL COLORS) PY add for P2 finishes add for P3 finishes 20 high EP2S( )1220N $551. $513. $479. $15. $ EP2S( )1820N EP2S( )2420N EP2S( )3020N EP2S( )3620N EP2S( )4220N EP2S( )4820N EP2S( )6020N Panels, Connections, Power and Accessories 25 high EP2S( )1225N EP2S( )1825N EP2S( )2425N EP2S( )3025N EP2S( )3625N EP2S( )4225N EP2S( )4825N EP2S( )6025N high EP2S( )1232N EP2S( )1832N EP2S( )2432N EP2S( )3032N EP2S( )3632N EP2S( )4232N EP2S( )4832N EP2S( )6032N high EP2S( )1237N EP2S( )1837N EP2S( )2437N EP2S( )3037N EP2S( )3637N EP2S( )4237N EP2S( )4837N EP2S( )6037N Example: EP2SPS3615N, 613 EP2S Stack-on panel PS Perforated Steel 36 Width 15 Height N No Slots 613 Silver trim Specify inserty type, insert color and trim color. Pricing listed above is for P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. NOTE: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. 55 Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on panels without slots do not allow for hanging components. Stack-on posts and connectors must be ordered separately.

56 Stack-On Fabric Panel with slots description w d h pattern no. grade add for P2 finishes add for P3 finishes 12 high EP1SF1212 $355. $366. $383. $390. $401. $408. $415. $426. $15. $ EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF high EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF high EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF high EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF Example: EP1SF3615, W565-3, 613 EP1SF Fabric stack-on panel 36 Width 15 Height W565-3 Flow-Celery Fabric 613 Silver trim Specify fabric and trim color. Pricing listed above is P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Note: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on posts and connectors must be ordered separately. 56

57 Stack-On Fabric Panel with slots description w d h pattern no. grade add for P2 finishes add for P3 finishes 20 high EP1SF1220 $379. $390. $409. $416. $428. $436. $443. $454. $15. $ EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF EP1SF Panels, Connections, Power and Accessories Example: EP1SF3615, W565-3, 613 EP1SF Fabric stack-on panel 36 Width 15 Height W565-3 Flow-Celery Fabric 613 Silver trim Specify fabric and trim color. Pricing listed above is P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Note: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on posts and connectors must be ordered separately. 57

58 Stack-On Fabric Panel without slots description w d h pattern no add for P2 finishes add for P3 finishes 12 high EP1SF1212N $355. $366. $383. $390. $401. $408. $415. $426. $15. $ EP1SF1812N EP1SF2412N EP1SF3012N EP1SF3612N EP1SF4212N EP1SF4812N EP1SF6012N high EP1SF1213N EP1SF1813N EP1SF2413N EP1SF3013N EP1SF3613N EP1SF4213N EP1SF4813N EP1SF6013N high EP1SF1215N EP1SF1815N EP1SF2415N EP1SF3015N EP1SF3615N EP1SF4215N EP1SF4815N EP1SF6015N high EP1SF1217N EP1SF1817N EP1SF2417N EP1SF3017N EP1SF3617N EP1SF4217N EP1SF4817N EP1SF6017N Example: EP1SF3615N, W565-3, 613 EP1SF Fabric stack-on panel 36 Width 15 Height N No slots W565-3 Flow-Celery Fabric 613 Silver trim Specify fabric and trim color. Pricing listed above is P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Note: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on panels without slots do not allow for hanging components. Stack-on posts and connectors must be ordered separately. 58

59 Stack-On Fabric Panel without slots description w d h pattern no add for P2 finishes add for P3 finishes 20 high EP1SF1220N $379. $390. $409. $416. $428. $436. $443. $454. $15. $ EP1SF1820N EP1SF2420N EP1SF3020N EP1SF3620N EP1SF4220N EP1SF4820N EP1SF6020N Panels, Connections, Power and Accessories 25 high EP1SF1225N EP1SF1825N EP1SF2425N EP1SF3025N EP1SF3625N EP1SF4225N EP1SF4825N EP1SF6025N high EP1SF1232N EP1SF1832N EP1SF2432N EP1SF3032N EP1SF3632N EP1SF4232N EP1SF4832N EP1SF6032N high EP1SF1237N EP1SF1837N EP1SF2437N EP1SF3037N EP1SF3637N EP1SF4237N EP1SF4837N EP1SF6037N Example: EP1SF3615N, W565-3, 613 EP1SF Fabric stack-on panel 36 Width 15 Height N No slots W565-3 Flow-Celery Fabric 613 Silver trim Specify fabric and trim color. Pricing listed above is P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Note: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. Stack-on panels will work on all generation panels by following the instructions listed at the beginning of this section. Stack-on panels without slots do not allow for hanging components. Stack-on posts and connectors must be ordered separately. 59

60 Stack-on Posts description w d h pattern no. P1 P2 P3 Standard 12 EP1SPC12 $85. $89. $ EP1SPC EP1SPC EP1SPC EP1SPC EP1SPC EP1SPC EP1SPC Extended for use with post covers 12 EP1SPC12E EP1SPC13E EP1SPC15E EP1SPC17E EP1SPC20E EP1SPC25E EP1SPC32E EP1SPC37E Example: EP1SPC25, 613 EP1SPC Stack-on post 25 Height 613 Silver trim Specify fabric and trim color. Pricing listed above is P1 trim colors. Add the appropriate upcharge if using P2 or P3 trim colors. Note: P2 trim colors should only be specified when using stack-on panels on top of EP3 panels. Post connectors must be ordered separately. 60 Stack-onpost must be used between adjacent stack-on panels. Standard stack-on post bottom uses a conical shaped bolt that connects it to the full height post directly beneath it. Post connectors for the top of the stack-on post must be ordered separately to match the geometry of the stack-on panels. Dual/Triple height posts can be used to transition between a full height panel and a lower height panel with a stack-on panel above (eg:80 h panel adjacent to a 60 h panel with a 20 h stack-on panel). Dual/Triple height posts allow a full height post cover to span the stack-on connection. Extended stack-on post bottom uses a double-threaded round connecter to attach to the full-height post directly beneath it. Multi-height post connectors (EP1PCMF) must be used on either side of this connector to provide a smooth transition for full-height post covers. Standard post connectors are used along the top of the stack-on panels.

61 Currents Service wall accessories panel starters, end starters and trim kits for Generation 1 and generation 2 panels and components description nominal height pattern no. list price panel starters 40 AA1EPS40 * 48 AA1EPS48 * 53 AA1EPS53 * 60 AA1EPS60 * 65 AA1EPS65 * Panels, Connections, Power and Accessories end starters 40 AX1E40 * 48 AX1E48 * 53 AX1E53 * 60 AX1E60 * 65 AX1E65 * end trim kits 39 H wall AX1EET39(T,R,L) * 48 H wall AX1EET48(T,R,L) * 64 H wall AX1EET64(T,R,L) * Crown end cap APT ( ) * Gap filler 40 /64 AX1EGF24 * 48 /64 AX1EGF16 * 53 /64 AX1EGF11 * 60 /64 AX1EGF4 * Example: AX1EET64T, 613 AX1 Accessory EET end trim 64 Panel trim T T both sides 613 Silver trim Specify legacy paint finish for end and panel starters, trim kits and crown end cap: Note: For more specific application information, please refer to pages of the 1999 Planning Guide.Additional finishes are available for crown end caps. *For pricing and discounting refer to the Currents price list. Leadtimes will be consistent with Currents published lead-times. 61 panel starters attach perpendicular panels to Currents wall structural base covers. panel starter includes clamp bracket and adapter. Both end and panel starters include top clip for added stiffness. No connector post is required for either starter. end starter supports perpendicular panel run on the centerline of the end of the wall. Perpendicular panels should be at the same height or higher than the service wall. The end trim kit encloses and flushes out the end of the Currents service wall with attached, end started panels. Specify trim kit suffix T for panels on both sides, L or R for attached panels only on left or right side of end of the Currents wall (as seen from outside of T end). Also specify crown end cap for all end conditions. Gap fillers fill the gap when attaching a lower height panel at the end of a 64 H Currents service wall.

62 Currents Service wall accessories panel starters, end starters and trim kits for Generation 3 panels and components description nominal height pattern no. list price panel starters 41 AA3EPS41 * 41 AA3EPS54 * 49 AA3EPS49 * 61 AA3EPS61 * 64 AA3EPS64 * end starters 41 AX3E41 * 49 AX3E49 * 54 AX3E54 * 61 AX3E61 * 64 AX3E64 * end trim kits 39 H wall AX1EET39(T,R,L) * 48 H wall AX1EET48(T,R,L) * 64 H wall AX1EET64(T,R,L) * Crown end cap APT ( ) * Gap filler 41 /64 AX1EGF24 * 49 /64 AX1EGF16 * 53 /64 AX1EGF11 * 61 /64 AX1EGF4 * Example: AX1EET64T, 613 AX1 Accessory EET end trim 64 Panel trim T T both sides 613 Silver trim Note: For more specific application information, please refer to pages of the 1999 Planning Guide.Additional finishes are available for crown end caps. *For pricing and discounting refer to the Currents price list. Leadtimes will be consistent with Currents published lead-times. 62 panel starters attach perpendicular panels to Currents wall structural base covers. panel starter includes clamp bracket and adapter. Both end and panel starters include top clip for added stiffness. No connector post is required for either starter. end starter supports perpendicular panel run on the centerline of the end of the wall. Perpendicular panels should be at the same height or higher than the service wall. The end trim kit encloses and flushes out the end of the Currents service wall with attached, end started panels. Specify trim kit suffix T for panels on both sides, L or R for attached panels only on left or right side of end of the Currents wall (as seen from outside of T end). Also specify crown end cap for all end conditions. Gap fillers fill the gap when attaching a lower height panel at the end of a 64 H Currents service wall.

63 E Series electrical systems consist of a 4-circuit and a 6-circuit system. Each circuit in the systems provides a maximum of 20 amps. The four circuit system has eight wires, the six-circuit system has ten wires. Both 8- and 10-wire systems contain two 10-gauge super neutrals and two ground wires so that sensitive electronic equipment may be easily protected from unwanted electrical interference. E Series electrical can be connected to either single phase or three-phase building power supplies. Specification Checklist The following is a general checklist to ensure your order has been specified properly and to expedite entry of your order. It should be reviewed by a qualified electrician to ensure compliance with any local code requirements. How to order electrical systems E Series electrical system 1. Base or ceiling infeed modules. One for each point of connection to the building power supply. Select model desired. Electrical connection to the building power supply must be made by a qualified electrician to ensure proper installation. 2. Select panels. Conduit jumpers are used to pass power to electrified panels. These panels do not have factory-installed power wiring, but modular power components are field-installed. 3. Shrouds must be used for each panel to panel point to complete the baseboard connection. Shrouds are included when post assemblies are ordered. Shrouds can also be ordered separately when building a multiple height connection. 4. Duplex receptacles. Specify the circuit which receptacles are to access: #1, #2, #3 and #4D for 2+2 info eight-wire applications and additionally #5D and #6D for ten wire applications. If connecting to single-phase supply, do not order #2 and #5D receptacles. 5. Select and order appropriate conduit jumpers to pass power between panels. Conduit Jumpers are for regular panel to panel connections or used to pass power through panels from terminal block to terminal block, which can be located up to 12 feet apart. To calculate correct jumper length: a. Add widths of both panels containing terminal blocks. b. Divide by 2. c. Add width of any non-electrified panels in-between. The result is the correct jumper length. Example: 6. Modular Wiring Components. Internal panel wiring is fully modular and is field-installed into the baseboard of panels. When wiring is field-installed the following components must be specified: Terminal blocks. To branch circuits, splice jumpers or locate receptacles. Blocks snap-lock into place and are always located in the center of a panel. Panels have one block location only. Base infeed and Ceiling Infeed Modules are each designed to plug into a terminal block, which must be ordered separately from the infeed. 7. Duplex Receptacles. Always specified separately according to circuit access. 8. Side Mount Receptacles. Available for panels 24 and wider. All standard receptacles fit into side mount position on right side of terminal block connector end. Therefore, no circuit number restriction. Special Considerations In addition to the checklist the following points should be remembered when planning a layout utilizing this electrical distribution system. 1. E Series electrical consists of four or six 20-amp circuits, any of which can be accessed as desired by plugging in a specially numbered receptacle at terminal block locations in panels. 2. Electrified panels can be interspersed between non-electrified panels with the use of extra-length jumpers in which to pass circuitry to the next electrified panel. 3. For isolation, the 2nd ground must be properly and separately grounded to the building by the installing electrician. 4. Certain cities or localities carry special codes limiting the use of certain items within this system. For instance, the City of Chicago requires that each power component be hard-wired at its location and therefore modular power systems are not allowed. products are available which comply with these code requirements. Knoll recommends contacting your local Sales Representative for clarification and possible restrictions. *Because of our continuous product improvements, these specifications are subject to change without notice. Please consult your Knoll Sales Representative for the latest information prior to ordering. Panels, Connections, Power and Accessories = = =78 Order EEIC78-8/10 63

64 Technical data E Series electrical systems To assist the specifier/electrician in specifying E Series electrical the following technical information is available.* Power Supply 8-Wire System The wiring in the panels is to be connected to the Multiple Branch circuit at a convenient spot on the building structure. This arrangement will provide 4 (four), 20-amp, 120-volt, 60-Hertz circuits. Power connections to single phase 120V, 120/240V split phase and three phase 120/208V supply are accommodated. The system components are sized for comparable ampacity throughout, except for receptacles which are rated 15 amp. The black, red, blue and pink hot leads are connected to the points of the V, 3 phase source with the white/black and white/red being a center tap neutral to provide 120V to each of the hot wires. A green ground wire is provided for the primary equipment ground. A second ground wire is provided for circuits that need to be separately grounded. 10-Wire System The ten wire system is almost identical to the eight wire system with the exception of the number of circuits provided. The ten wire system offers the ability to provide six circuits through one power entry. This is accomplished with the addition of two more hot leads. They are colored tan and orange and are paired with the white/red neutral wire. Electrical components are labeled for identification. Electrical Infeed Two different types of infeeds are provided which are specially designed to connect to the two general categories of building distribution: ceiling distribution in raceways ending in junction boxes and floor duct or wall outlets. Base Infeed Module: Modular base-mounted infeed conduits in eight-wire and ten-wire versions are provided for connection to building power supplies housed in underfloor outlet boxes, floor mounted (monuments) or wall outlet boxes. Available unhanded for ease in introducing power from left or right of infeed location. The cover plates of floor monuments, recessed floor boxes or wall boxes are to be punched to receive a half-inch (trade size) knockout hole for installation of the box fitting, which is included on the infeed circuit. The wiring connection is to be made within the box inside the monument or behind the floor or wall flush plate. The 4 1 /2 conduit can be shortened to meet field conditions by cutting the infeed (loose) end. Base Infeed Module plugs into terminal block at the receptacle location. For New York base infeed, see Planning Guide. Ceiling Infeed Module: The straight tubular infeed may be shortened (on its bottom end) if it will not telescope sufficiently into the module to fit field conditions. Ceiling Infeed Module is filled with 8- or 10- wire conduit and plugs into terminal block in adjacent panel. Harness length is 19. Upper tube of module is 79 in length. Raceway Panels with field-installed componentry: 1. An independent cableway with capacity for up to ten 3 /8 dia. communications cables. 2. Multiple Branch Circuit power wiring consisting of eight or ten wire providing four or six separate 20-amp circuits, plus an isolated ground and two 10-gauge neutrals. 3. A terminal block at the center of the panel baseboard for panel-to-panel electrical connection and placement of duplex receptacles. 4. Two locations, one on each side of the center of the panel (back to back), into which duplex 15-amp receptacles can be placed. The raceway covers are provided with removable knockouts. For increased electric demands a second duplex receptacle per panel side can be added to panels 24 and wider. This receptacle plugs directly into the right side terminal block connector ends. Any standard E Series receptacle may be used. 5. End-to-end and face-to-face symmetry for ease in ordering, erecting and installation of power and communications cabling. The faceplates on both sides of the panel are removable without removing receptacles. The system and all standard components are UL-listed. *Because of our continuous product improvements, these specifications are subject to change without notice. Please consult a Knoll Sales Representative for the latest information prior to ordering. 64

65 To assist the specifier/electrician in specifying O Series the following technical information is available.* Power Supply Electrical Infeed Two different types of infeeds are provided which are specially designed to connect to the two general categories of building distribution: ceiling distribution in raceways ending in junction boxes and floor duct or wall outlets. Base Infeed Module: Modular base-mounted infeed conduits are provided for connection to building power supplies housed in underfloor outlet boxes, floor mounted or wall outlet boxes. Available unhanded for ease in introducing power from left or right of infeed location. The cover plates of floor monuments, recessed floor boxes or wall boxes are to be punched to receive a half-inch (trade size) knockout hole for installation of the box fitting, which is included on the infeed circuit. The wiring connection is to be made within the box inside the monument or behind the floor or wall flush plate. The 4 1 /2 conduit can be shortened to meet field conditions by cutting the infeed (loose) end. Base Infeed Module plugs into terminal block. Technical data O Series electrical systems Ceiling Infeed Module: The straight tubular infeed may be shortened (on its bottom end) if it will not telescope sufficiently into the module to fit field conditions. Ceiling Infeed Module is filled with 8- wire conduit and plugs into terminal block in adjacent panel. Raceway Panels with field-installed componentry: 1. An independent cableway with capacity for up to ten 3 /8 dia. communications cables. 2. Multiple Branch Circuit power wiring consisting of eight wire providing four separate 20-amp circuits, plus an isolated ground. 3. A terminal block at the center of the panel baseboard for panel-to-panel electrical connection and placement of duplex receptacles. 4. Two locations, one on each side of the center of the panel (back to back), into which duplex 15-amp receptacles can be placed. The raceway covers are provided with removable knockouts. For increased electric demands a second duplex receptacle per panel side can be added to panels 36 and wider. The Side Mount Receptacle (SMR3) plugs directly into the left side terminal block connector ends and always accesses circuit #3. 5. End-to-end and face-to-face symmetry for ease in ordering, erecting and installation of power and communications cabling. The faceplates on both sides of the panel are removable without removing receptacles. The system and all standard components are UL-listed. *Because of our continuous product improvements, these specifications are subject to change without notice. Please consult a Knoll Sales Representative for the latest information prior to ordering. Panels, Connections, Power and Accessories 65

66 Ceiling infeeds for Generation 1 and Generation 2 panels description type w d h pattern no. P1 P2 P3 Metal/plastic ceiling module (Upper plastic tube length is 79 ) /2 40 EE1CM40P $185. n/a $ /2 48 EE1CM48P 185. n/a /2 53 EE1CM53P 229. n/a /2 60 EE1CM60P 274. n/a /2 65 EE1CM65P 288. n/a /2 80 EE1CM80P 397. n/a 438. Metal/plastic ceiling module (Upper plastic tube length is 120 ) /2 40 EE1CM40PE 237. n/a /2 48 EE1CM48PE 237. n/a /2 53 EE1CM53PE 282. n/a /2 60 EE1CM60PE 327. n/a /2 65 EE1CM65PE 341. n/a /2 80 EE1CM80PE 449. n/a 495. Example: EE1CM60P, 115 EE1 electrical CM Ceiling module 60 Height P Painted/Plastic 115 Medium Grey (Slate) trim For ceiling infeed modules: Specify trim (paint) color. Fabric covered modules not available. Note: E Series and O Series electrical components are not interchangeable. 8-wire components listed work for both 2+2 and 3+1 configurations. To connect a metal ceiling infeed to a corner or straight connection use an adjustable angle connector or an adjustable angle connector with multi-height connector for a three-way connection. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 66 Ceiling infeed modules: Electrical harnesses not included with modules. Modules are hollow to accommodate power and/or data cables from source into systems furniture. With electrical harness installed, infeed holds 35 cables. Cables/conduit are laid into the lower metal body by removal of the front 1-1/2 wide access cover and into the upper plastic extrusion by separating the front edge of the pliable tube. Infeed module is attached to an available post location of the appropriate height. The module connot be used for panel suppoet and there are no hang on capabilities. Includes escutcheon plate. Plate and plastic tube are white to integrate with standard ceiling color. No hang on capabilities. Module cannot be used for panel support. Painted metal module is 120 long metal extrusion with attachment hooks at proper height to attach to appropriate height post. Infeed holds 35 cables with electrial harness installed. Cables/conduit are laid into module by removal of two-piece front 1-1/2 wide vertical access cover which runs the length of the extrusion. Includes escutcheon plate which is white to integrate with ceiling. Tube is trim colored to match system trim. To connect a metal ceiling infeed to a corner or a straight connection you must use an adjustable angle connector or adjustable angle connector with a multi-height post connector.

67 Ceiling infeeds for Generation 1 and Generation 2 panels description type w d h pattern no. P1 P2 P3 Painted metal ceiling module length /2 120 EE1CM40M $421. n/a $ /2 120 EE1CM48M 421. n/a /2 120 EE1CM53M 421. n/a /2 120 EE1CM60M 421. n/a /2 120 EE1CM65M 421. n/a /2 120 EE1CM80M 421. n/a 464. Panels, Connections, Power and Accessories Ceiling infeed harness length E-Series 10-wire EE1CH n/a n/a E-Series 8-wire EE1CH n/a n/a Example: EE1CM60P, 115 EE1 electrical CM Ceiling module 60 Height P Painted/Plastic 115 Medium Grey (Slate) trim For ceiling infeed modules: Specify trim (paint) color. Fabric covered modules not available. Note: E Series and O Series electrical components are not interchangeable. 8-wire components listed work for both 2+2 and 3+1 configurations. To connect a metal ceiling infeed to a corner or straight connection use an adjustable angle connector or an adjustable angle connector with multi-height connector for a three-way connection. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. 67 Ceiling infeed modules: Electrical harnesses not included with modules. Modules are hollow to accommodate power and/or data cables from source into systems furniture. With electrical harness installed, infeed holds 35 cables. Cables/conduit are laid into the lower metal body by removal of the front 1-1/2 wide access cover and into the upper plastic extrusion by separating the front edge of the pliable tube. Infeed module is attached to an available post location of the appropriate height. The module connot be used for panel suppoet and there are no hang on capabilities. Includes escutcheon plate. Plate and plastic tube are white to integrate with standard ceiling color. No hang on capabilities. Module cannot be used for panel support. Painted metal module is 120 long metal extrusion with attachment hooks at proper height to attach to appropriate height post. Infeed holds 35 cables with electrial harness installed. Cables/conduit are laid into module by removal of two-piece front 1-1/2 wide vertical access cover which runs the length of the extrusion. Includes escutcheon plate which is white to integrate with ceiling. Tube is trim colored to match system trim. To connect a metal ceiling infeed to a corner or a straight connection you must use an adjustable angle connector or adjustable angle connector with a multi-height post connector.

68 Ceiling infeeds for Generation 3 panels description type w d h pattern no. P1 P2 P3 Metal/plastic ceiling module (Upper plastic tube length is 79 ) /2 41 EE3CM41P $185. $201. $ /2 49 EE3CM49P /2 54 EE3CM54P /2 61 EE3CM61P /2 64 EE3CM64P /2 81 EE3CM81P Metal/plastic ceiling module (Upper plastic tube length is 120 ) /2 40 EE3CM41PE /2 49 EE3CM49PE /2 54 EE3CM54PE /2 61 EE3CM61PE /2 64 EE3CM64PE /2 81 EE3CM81PE Example: EE3CM61P, 115 EE3 electrical Generation 3 CM Ceiling module 61 Height P Painted/Plastic 115 Medium Grey (Slate) trim For ceiling infeed modules: Specify trim (paint) color. Fabric covered modules not available. Note: E Series and O Series electrical components are not interchangeable. 8-wire components listed work for both 2+2 and 3+1 configurations.to connect a metal ceiling infeed to a corner or straight connection use an adjustable angle connector or an adjustable angle connector with multi-height connector for a three-way connection. 68 Ceiling infeed modules: Electrical harnesses not included with modules. Modules are hollow to accommodate power and/or data cables from source into systems furniture. With electrical harness installed, infeed holds 35 cables. Cables/conduit are laid into the lower metal body by removal of the front 1-1/2 wide access cover and into the upper plastic extrusion by separating the front edge of the pliable tube. Infeed module is attached to an available post location of the appropriate height. The module connot be used for panel suppoet and there are no hang on capabilities. Includes escutcheon plate. Plate and plastic tube are white to integrate with standard ceiling color. No hang on capabilities. Module cannot be used for panel support. Painted metal module is 120 long metal extrusion with attachment hooks at proper height to attach to appropriate height post. Infeed holds 35 cables with electrial harness installed. Cables/conduit are laid into module by removal of two-piece front 1-1/2 wide vertical access cover which runs the length of the extrusion. Includes escutcheon plate which is white to integrate with ceiling. Tube is trim colored to match system trim. To connect a metal ceiling infeed to a corner or a straight connection you must use an adjustable angle connector or adjustable angle connector with a multi-height connector.

69 Ceiling infeeds for Generation 3 panels description type w d h pattern no. P1 P2 P3 Painted metal ceiling module length /2 120 EE3CM41M $421. $441. $ /2 120 EE3CM49M /2 120 EE3CM54M /2 120 EE3CM61M /2 120 EE3CM64M /2 120 EE3CM81M Panels, Connections, Power and Accessories Example: EE3CM61P, 115 EE3 electrical Generation 3 CM Ceiling module 61 Height P Painted/Plastic 115 Medium Grey (Slate) trim For ceiling infeed modules: Specify trim (paint) color. Fabric covered modules not available. Note: E Series and O Series electrical components are not interchangeable. 8-wire components listed work for both 2+2 and 3+1 configurations.to connect a metal ceiling infeed to a corner or straight connection use an adjustable angle connector or an adjustable angle connector with multi-height connector for a three-way connection. 69 Ceiling infeed modules: Electrical harnesses not included with modules. Modules are hollow to accommodate power and/or data cables from source into systems furniture. With electrical harness installed, infeed holds 35 cables. Cables/conduit are laid into the lower metal body by removal of the front 1-1/2 wide access cover and into the upper plastic extrusion by separating the front edge of the pliable tube. Infeed module is attached to an available post location of the appropriate height. The module connot be used for panel suppoet and there are no hang on capabilities. Includes escutcheon plate. Plate and plastic tube are white to integrate with standard ceiling color. No hang on capabilities. Module cannot be used for panel support. Painted metal module is 120 long metal extrusion with attachment hooks at proper height to attach to appropriate height post. Infeed holds 35 cables with electrial harness installed. Cables/conduit are laid into module by removal of two-piece front 1-1/2 wide vertical access cover which runs the length of the extrusion. Includes escutcheon plate which is white to integrate with ceiling. Tube is trim colored to match system trim. To connect a metal ceiling infeed to a corner or a straight connection you must use an adjustable angle connector or adjustable angle connector with a multi-height connector.

70 E Series electrical 8-wire/10-wire base infeed modules description type w d h pattern no. list price Base infeed module - E Series (non-handed) 8-wire 54 EE1BI-8 $ wire 72 EE1BI wire 54 EE1BI wire 72 EE1BI New York base infeeds 10-wire EE1BI-10N wire EE1BI-8N 205. Jumper end base feed E Series 10-wire w/ground, 72 EE1BIJ-10G wire, 72 EE1BIJ wire w/ground, 72 EE1BIJ-8G wire, 72 EE1BIJ Example: EE1BI-10 EE1BI Base infeed wire 8-wire components listed work for both 2+2 and 3+1 configurations. Base infeed modules: An infeed conduit that connects to the wall or floor outlet box of a building s power supply and plugs into a terminal block in panel raceway. Power entry can be from either left or right side of panel. Injection molded cover conceals the baseboard connection and is reversible for either left or right entry. Can be field-cut to proper lengths. Color is black. A terminal block must be ordered separately. Jumper end infeeds: Connects by hardwiring to a building s electrical supply in floor or wall box. Plugs into one set of terminal connections at end of Terminal Block Terminal Block must be located inpanel adjacent to source. Terminal Block is ordered separately. Can be field cut by a certified electricaian to necessary length. Conduit is encased in black plastic sealer. 70

71 E Series electrical 8-wire/10-wire conduit jumper description nominal length actual length pattern no. 8-wire 10-wire Conduit jumper /2 EE1C18-(8 /10) $73. $ /2 EE1C21-(8 /10) /2 EE1C24-(8 /10) /2 EE1C27-(8 /10) /2 EE1C30-(8 /10) /2 EE1C33-(8 /10) /2 EE1C36-(8 /10) /2 EE1C39-(8 /10) /2 EE1C42-(8 /10) /2 EE1C45-(8 /10) /2 EE1C48-(8 /10) /2 EE1C51-(8 /10) /2 EE1C54-(8 /10) /2 EE1C57-(8 /10) /2 EE1C60-(8 /10) /2 EE1C63-(8 /10) /2 EE1C66-(8 /10) /2 EE1C69-(8 /10) /2 EE1C72-(8 /10) /2 EE1C75-(8 /10) /2 EE1C78-(8 /10) /2 EE1C81-(8 /10) /2 EE1C84-(8 /10) /2 EE1C87-(8 /10) /2 EE1C90-(8 /10) /2 EE1C93-(8 /10) /2 EE1C96-(8 /10) /2 EE1C99-(8 /10) /2 EE1C102-(8 /10) /2 EE1C105-(8 /10) /2 EE1C108-(8 /10) /2 EE1C111-(8 /10) /2 EE1C114-(8 /10) /2 EE1C120-(8 /10) /2 EE1C126-(8 /10) /2 EE1C132-(8 /10) /2 EE1C144-(8 /10) Panels, Connections, Power and Accessories Example: EE1C30-8 EE1C Conduit jumper 30 Length 8 8-wire 8-wire components listed work for both 2+2 and 3+1 configurations. Jumpers: Transmit power circuits from one panel mouted terminal block to another. Can carry power through panels where no terminal blocks are installed. The length of the jumper corresponds to the distance between the terminal blocks. To calculate the correct length: 1. Add widths of both panels containing terminal blocks. 2. Divide by two. 3. Add width of any non-electrified panels in-between. The result is the correct jumper length. Example: = = =78 Order EE1C78-8/10 71

72 E Series electrical 8-wire/10-wire components description type actual length pattern no. list 8-wire 10-wire 8-wire wire wire 3+3 Panel-to-panel flat flexible connectors Used only with adjacent panels 11 1 /2 EE1CF18(8/10) $76. $76. $ /2 EE1CF24(8/10) /2 EE1CF30(8/10) Terminal block EE1TB(8/10) KnollNow applicable to 8-wire only Duplex receptacle Circuit #1 EE1R Circuit #2 EE1R Circuit #3 dedicated for 2+2 EE1R3D n/a 28. n/a Circuit #3 for EE1R3 28. n/a 28. Circuit #4 dedicated circuit for 3+1, 2+2 or 3+3 EE1R4D Circuit #5 dedicated circuit for 3+3 EE1R5D n/a n/a 28. Circuit #6 dedicated circuit for 3+3 EE1R6D n/a n/a 28. E Series side mount receptacle bracket package of 10 EE1SMRB Data shield Terminal block shield EE15BR Example: EE1R3 EE1R Duplex receptacle 3 Circuit #3 Receptacles are black only. E Series and O Series electrical components are not interchangeable. 72 Neutral wires are 10 gauge. Side mount receptacles: Plugs directly into the right side of terminal block to provide a second duplex receptacle where required. Any E Series receptacle can be used in panels 24 wide and wider. Side mount receptacle bracket (EE1SMRB10) is needed when using a side mount receptacle. Terminal Block: A modular eight or ten wire block that snaps into the baseboard location in the center of the panel. Used to branch circuits, splice jumpers, or locate duplex receptacles back to back.

73 E Series electrical Dedicated Neutral System conduit jumper description nominal length pattern no. list Base infeed module 54 EE1BI-(N3/N4)e $ EE1BI72-(N3/N4)e 223. Panels, Connections, Power and Accessories Conduit jumper 18 EE1C18-(N3/N4)e EE1C21-(N3/N4)e EE1C24-(N3/N4)e EE1C27-(N3/N4)e EE1C30-(N3/N4)e EE1C33-(N3/N4)e EE1C36-(N3/N4)e EE1C39-(N3/N4)e EE1C42-(N3/N4)e EE1C45-(N3/N4)e EE1C48-(N3/N4)e EE1C51-(N3/N4)e EE1C54-(N3/N4)e EE1C57-(N3/N4)e EE1C60-(N3/N4)e EE1C63-(N3/N4)e EE1C66-(N3/N4)e EE1C69-(N3/N4)e EE1C72-(N3/N4)e EE1C75-(N3/N4)e EE1C78-(N3/N4)e EE1C81-(N3/N4)e EE1C84-(N3/N4)e EE1C87-(N3/N4)e EE1C90-(N3/N4)e EE1C93-(N3/N4)e EE1C96-(N3/N4)e EE1C99-(N3/N4)e EE1C102-(N3/N4)e EE1C105-(N3/N4)e EE1C108-(N3/N4)e EE1C111-(N3/N4)e EE1C114-(N3/N4)e EE1C120-(N3/N4)e 197. Example: EE1C30-N3 EE1C Conduit jumper 30 Length N3 8-wire dedicated neutral 8-wire N3 = 2+1 system (2 hots and 2 neutrals sharing one ground, 1 isolated hot and 1 isolated neutral on an isolated ground) 10-wire N4 = 2+2 system (2 hots and 2 neutrals sharing one ground, 2 hots and 2 neutrals sharing another ground) Jumpers: Transmit power circuits from one panel mouted terminal block to another. Can carry power through panels where no terminal blocks are installed. The length of the jumper corresponds to the distance between the terminal blocks. To calculate the correct length: 1. Add widths of both panels containing terminal blocks. 2. Divide by two. 3. Add width of any non-electrified panels in-between. The result is the correct jumper length. Example: = = =78 Order EE1C78-N3 73

74 E Series electrical Dedicated Neutral System conduit jumper description nominal length pattern no. list Conduit jumper 126 EE1C126-(N3/N4)e $ EE1C132-(N3/N4)e EE1C144-(N3/N4)e 217. Terminal block (N3/N4) EE1TB-(N3/N4)e 48. Duplex receptacle EE1RIIINe 30. EE1RIINe 30. EE1RINe 30. EE1RIVNe 30. Example: EE1C30-N3 EE1C Conduit jumper 30 Length N3 8-wire dedicated neutral 8-wire N3 = 2+1 system (2 hots and 2 neutrals sharing one ground, 1 isolated hot and 1 isolated neutral on an isolated ground) 10-wire N4 = 2+2 system (2 hots and 2 neutrals sharing one ground, 2 hots and 2 neutrals sharing another ground) 74 Jumpers: Transmit power circuits from one panel mouted terminal block to another. Can carry power through panels where no terminal blocks are installed. The length of the jumper corresponds to the distance between the terminal blocks. To calculate the correct length: 1. Add widths of both panels containing terminal blocks. 2. Divide by two. 3. Add width of any non-electrified panels in-between. The result is the correct jumper length. Example: = = =78 Order EE1C78-N3

75 O Series electrical Ceiling infeed/base infeed modules description type w d h pattern no. P1 P2 P3 Raceway ceiling infeed module - O Series 8-wire 4 48 OIM48H-8e $501. n/a $ OIM53H-8e 561. n/a OIM60H-8e 621. n/a OIM65H-8e 643. n/a OIM80H-8e 788. n/a 822. Panels, Connections, Power and Accessories Base infeed module - O Series 8 wire (non-handed) 48 OBIe 218. n/a n/a 72 OBI72e 264. n/a n/a Ceiling infeed harness length O Series 8-wire OEICH-8e 432. n/a n/a Electrical system adapter jumper O Series to E Series adapter jumper EE1AP12-8e 114. n/a n/a Example: OIM60H-8, 117 OIM Raceway ceiling infeed module 60 Height (panel) H Hard wired 8 8-wire electrical 117 Soft grey trim For ceiling infeed module: Specify module trim color. Note: O series and E series electrical components are not interchangeable. O series ceiling infeeds will not work with EP3 panels. 75 Raceway ceiling infeed module: Electrical harness included with O series ceiling infeeds only. Supplies power from building source with hard-wired capabilities. Vertical segment of wiring connects to a building junction box above finished ceiling. Ceiling height above panel cannot be more than 6 feet. Total module height is 79. Length of conduit harness is The rigid infeed tube accommodates the power conduit and ten 3 /8 communications cables which are laid-in by removal of module front access cover. Infeed module can be attached to any available post location perpendicular to the panel run. The module cannot be used for panel support. No hang-on capabilities. Ceiling plate and tube are white to integrate with standard ceilings. Base infeed modules: An infeed conduit that connects to the wall or floor outlet box of a building s power supply and plugs into a terminal block in panel baseboard. Power entry can be from either left or right side of panel. Injection molded cover conceals the baseboard connection and is reversible for either left or right entry. Can be field-cut to proper lengths. Color is black. A terminal block must be ordered separately. Electrical system adaptor jumper: A12 jumper which connects an O series terminal block to an E series jumper.

76 O Series electrical Conduit jumper 8-wire description nominal L actual L pattern no. 8-wire Conduit jumper /2 OCC15-(8)e $ /2 OCC18-(8)e /2 OCC21-(8)e /2 OCC24-(8)e /2 OCC27-(8)e /2 OCC30-(8)e /2 OCC33-(8)e /2 OCC36-(8)e /2 OCC39-(8)e /2 OCC42-(8)e /2 OCC45-(8)e /2 OCC48-(8)e /2 OCC51-(8)e /2 OCC54-(8)e /2 OCC57-(8)e /2 OCC60-(8)e /2 OCC63-(8)e /2 OCC66-(8)e /2 OCC69-(8)e /2 OCC72-(8)e /2 OCC75-(8)e /2 OCC78-(8)e /2 OCC81-(8)e /2 OCC84-(8)e /2 OCC87-(8)e /2 OCC90-(8)e /2 OCC93-(8)e /2 OCC96-(8)e /2 OCC99-(8)e /2 OCC102-(8)e /2 OCC105-(8)e /2 OCC108-(8)e /2 OCC111-(8)e /2 OCC114-(8)e /2 OCC120-(8)e /2 OCC126-(8)e /2 OCC132-(8)e /2 OCC144-(8)e 238. Example: OCC30-8 OCC Conduit jumper 30 Length 8 Electric (8-wire) Jumpers: Transmit power circuits from one panel mounted terminal block to another. Can carry power through panels where no terminal blocks are installed. The length of the jumper corresponds to the distance between the terminal blocks. To calulate the correct length: 1. Add widths of both panels containing terminal blocks. 2. Divide by two. 3. Add width of any non-electrified panels in-between. The result is the correct jumper length. 76 Example: = = =78 Order OCC78-6/8

77 O Series electrical components 8-wire description type l pattern no. 8-wire Panel-to-panel flat flexible connectors Used only with adjacent 12 panels 8 1 /2 OCF12-(8)e $82. Panels, Connections, Power and Accessories Terminal block OTB-(8)e 55. Duplex receptacle Circuit #1 OR1e 37. Circuit #2 OR2e 37. Circuit #3 OR3e 37. Circuit #4 OR4 37. Circuit #4 dedicated OR4De 47. Side mount duplex receptacle (circuit #3) OSMR3e 63. O Series side mount receptacle bracket package of 10 OSMRB10e 290. O Series terminal block bracket package of 10 OTBK10e 38. Data shield Terminal block shield EE15BR 52. Example: OR3 OR Duplex receptacle 3 Circuit #3 Available in black only. O series and E series electrical components are not interchangeable. Duplex receptacle (OR series): Each of the 8-wire receptacles engage a different combination of three of the circuit legs in the terminal blocks. Receptacles #1, #2, and #3 engage lines 1,2 and 3 respectively plus shared neutral and G1 equipment ground (or common ground). Receptacle #4 engages line 4 and separate N2 neutral plus G1 equipment ground. Receptacle #4D engages line 4 and separate N2 neutral plus the isolated ground. Specify this when a dedicated circuit is installed. Shared neutral wire is 10 gauge. Side mount receptacle (OSMR3): Plugs directly into left side of terminal block to provide a second duplex receptacle where reequired. Always accesses Circuit #3. Can only be used on EP1 panels 36 or wider. Side mount receptacle bracket (OBSMRB): Side mount bracket must be ordered when using an SMR3 receptacle with EP1- Panel. Panel-to-panel flat flexible connector (OCF series): To carry power from one 12 electrified panel to an adjacent 12 electrified panel. Terminal block: A modular eight-wire block that snaps into the baseboard location in the center of the panel. Used to branch circuits, splice jumpers, or locate duplex receptacles back to back. Terminal block bracket is provided when ordering terminal block. OBOTBK is used only with EP1 Panels. 77

78 Electrical/Communication accessories description type w d h pattern no. list price Desktop Power Module, clamp mount 108 cord 3 3 /4 4 1 /2 EE2WSME108 $ cord 3 3 /4 4 1 /2 EE2WSME Desktop Data module, clamp mount 3 3 /4 2 1 /2 5 EE2WSMC 90. Desk top power and communications module, clamp mount 108 cord length EE2WSMED cord length EE2WSMED Raceway accessory Knock-out replacement cover (N, O, V series panel outlets and EP1, EP2 and EP3 electrical) Knock-out replacement cover (N, O, V series panel outlets and EP1, EP2 and EP3 electrical) Package of 10. Knock-out replacement cover - side mount receptacle ( O Series) EE1KC 10. EE1KC OE1SMKC 10. Surge suppressor EE1SS Example: EE1WSME EE1WSM Duplex Monument E Electrical Worksurface modules are available in black only. Specify trim color for raceway accessory only. Electrical center is two-tone Neutral and Brown. Communication module does not include communication faceplates or jacks. Desktop modules: Duplex electrical and communications outlets that attach at any point along the rear of a worksurface. Accommodates surfaces 1 to 1 3 /4 thick. Monument requires no drilling. Clamps to back of worksurface with included bracketry. 78 Knock-out replacement cover: Injection molded plastic piece which snaps into raceway cover of a panel where electrification is no longer required.

79 DataWay Transitions and Channels description type w d h pattern no. P1 P2 P3 Transitions 180 straight 3 1 /2 1 1 /2 2 EC1DWS $9. n/a $10. 3-way 3 1 /2 1 1 /2 2 EC1DWT 9. n/a way 3 1 /2 2 1 /2 2 EC1DWX 9. n/a 10. Corner 3 1 /2 1 1 /2 2 EC1DWL 9. n/a 10. Corner, post, cover 3 1 /2 2 1 /2 2 EC1DWLK 9. n/a 10. End 3 1 /2 1 1 /2 2 EC1DWE 9. n/a 10. End panel 3 1 /2 2 1 /2 2 EC1DWEP 9. n/a 10. End, post cover 3 1 /2 2 1 /2 2 EC1DWEK 9. n/a 10. Multi-height filler 3 1 /2 2 1 /2 2 EC1DWMF 9. n/a 10. Panels, Connections, Power and Accessories Horizontal top channel 9 1 /2 1 1 /2 2 EC1DW n/a /8 2 EC1DWEPTC 44. n/a /2 1 1 /2 2 EC1DW n/a /2 1 1 /2 2 EC1DW n/a /2 1 1 /2 2 EC1DW n/a /2 1 1 /2 2 EC1DW n/a /2 1 1 /2 2 EC1DW n/a /2 1 1 /2 2 EC1DW n/a /2 1 1 /2 2 EC1DW n/a 124. Example: EC1DWS, 117 EC1DW DataWay S Straight transition 117 Soft Grey trim Specify trim color. Note: DataWay is for low voltage communications cabling only. High voltage electrical cables cannot be routed through DataWay. Note: Dataway Components only compatible with EP1/EP2 panels. 79 A family of parts that can be mounted to the top of EP1 or EP2 panels. Will accommodate up to 30 category 5 data/communications cables in the straight run. No fishing of cables is required for installation. Transition pieces: Injection-molded plastic pieces that fill the space between panels and are installed after the cables are laid in. Horizontal channels: A2 high aluminum extrusion which has the same length as the panel top caps and is open on the top. Panel top caps are removed and the DataWay channels mounted to the top of the panel. Cables are laid into the channel and the panel top cap then snaps onto the top of the channel to close it.

80 DataWay Ceiling Infeed and Cable Manager description w d h pattern no. P1 P2 P3 Vertical ceiling rigid infeed panel kit 3 1 /2 1 1 /2 55 EC1DWCI $289. n/a $318. Vertical cable manager 1 1 /2 3 /8 77 EC1DWVCM n/a 55. Example: EC1DWCI, 117 EC1DW DataWay CI Ceiling infeed 117 Soft grey Specify trim color. Ceiling infeed tubes available in white only. Length=79. Note: DataWay components only compatible with EP1/EP2 panels. 80 Vertical ceiling infeed module: Allows for up to 25 category 5 data communications cables to be run from the ceiling into DataWay channels. Attaches over any post. Vertical cable manager: Allows for the routing of 6 category 5 cables vertically along the face of an exposed post. Available in one length and can be field cut for exiting cables at any desired height.

81 DataTrak Transitions and Channels description type w d h pattern no. P1 P2 P3 Transitions 180 straight, no cut-outs 3 1 /2 1 1 /2 5 EC1DTS $11. n/a $ straight, one cut-out 3 1 /2 1 1 /2 5 EC1DTS1C 17. n/a straight, one knockout 3 1 /2 1 1 /2 5 EC1DTS1K 12. n/a straight, two cut-outs 3 1 /2 1 1 /2 5 EC1DTS2C 17. n/a straight, two knockouts 3 1 /2 1 1 /2 5 EC1DTS2K 12. n/a corner round 3 1 /2 2 1 /2 5 EC1DTL 11. n/a 12. End filler /2 5 EC1DTEP 11. n/a 12. End round 3 1 /2 2 1 /2 5 EC1DTE 11. n/a 12. Four-way 3 1 /2 2 1 /2 5 EC1DTX 11. n/a 12. Three-way /2 3 1 /2 5 EC1DTY 11. n/a 12. Three-way, no cut-out 3 1 /2 2 1 /2 5 EC1DTT 11. n/a 12. Three-way, with cut-out 3 1 /2 2 1 /2 5 EC1DTT1C 17. n/a 19. Three-way, with knockout 3 1 /2 2 1 /2 5 EC1DTT1K 12. n/a 15. Two-way /2 3 5 EC1DT n/a 12. Panels, Connections, Power and Accessories Horizontal channel 9 1 /2 1 1 /2 5 EC1DT n/a /2 1 1 /2 5 EC1DT n/a /2 1 1 /2 5 EC1DT n/a /2 1 1 /2 5 EC1DT n/a /2 1 1 /2 5 EC1DT n/a /2 1 1 /2 5 EC1DT n/a /2 1 1 /2 5 EC1DT n/a /2 1 1 /2 5 EC1DT n/a 152. Example: EC1DT48, 117 EC1DT DataTrak 48 Width in inches 117 Soft Grey trim Specify trim color. Note: Datatrak is for low voltage duty/communications cabling only. High voltage electrical cables cannot be routed through DataTrak. Do not use with post covers or on end panels. Note: DataTrak Components only compatible with EP1/EP2 panels. 81 A family of parts that can be mounted to the top of Raceway panels. Will accommodate up to 30 Category 5 data/communications cables in the straight run and 15 Category 5 cables in a 90 configuration. No fishing of cables is required for installation. Transition pieces:injection-molded plastic pieces that fill the space between panels and are installed after the cables are laid in. Cut-out allows interface with a 65 high panel while knockouts provide vertical cable exits. Horizontal channel: A5 high aluminum extrusion which has the same length and thickness as the panel top caps and is open on the top. The 5 height, when added to a 60 panel, allows for even alignment with a 65 panel. Panel top caps are removed adn the DataTrak channels mounted to the top of the panel. Cables are laid into the channel and the panel top cap then snaps onto the top of the channel to close it.

82 DataTrak Ceiling Infeed and Cable Manager description w d h pattern no. P1 P2 P3 Ceiling infeed panel kit /2 55 EC1DTCI24 $255. n/a $ /2 55 EC1DTCI n/a /2 55 EC1DTCI n/a /2 55 EC1DTCI n/a /2 55 EC1DTCI n/a 437. Ceiling infeed module /2 120 ECIDTVCI40e 443. n/a /2 120 ECIDTVCI n/a /2 120 ECIDTVCI53e 443. n/a /2 120 ECIDTVCI n/a /2 120 ECIDTVCI n/a 489. Vertical cable manager 1 1 /2 5 /8 77 EC1DTVCM Example: EC1DTCI48, 117 EC1DT DataTrak CI Ceiling infeed 48 Width 117 Soft grey Specify trim color. The EC1DTVCM80 cannot be used behind worksurfaces or components which span the post. Ceiling infeed tubes available in white only. Note: DataTrak Components only compatible with EP1/EP2 panels. 82 Vertical cable manager: Allows for the routing of three cables vertically along the face of exposed post. Available in one length and can be field cut for exiting cables at any desired height. Ceiling infeed module: Allows for up to 25 Category 5 data/communications cables to be run from the ceiling into DataTrak channels. Attaches to any exposed post. Ceiling infeed panel kit: Fits on top of an existing panel. Allows for 12 Category 5 cables to be fed directly into DataTrak channels.

83 Panel accessories Cable and Wire Managers description type w d h pattern no. P1 P2 P3 Vertical wire manager 1 /2 3 /4 80 EC1VWM80 $20. $21. $22. Panels, Connections, Power and Accessories Example: EC1VWM80, 117 EC1VWM Vertical Wire Manager 80 Length 117 Soft Grey trim Specify trim color. Vertical wire manager: A plastic strip designed to hide a cord running down the edge of the panel. Cut to desired length in field. 83

84 Panel accessories Coat Hook, Coat Hanger and Carpet Grips description type w d h pattern no. P1 P2 P3 EP1 Coat hook 6/carton 1 /2 3 /4 5 EP1CH $81. n/a n/a Coat hanger 17 3 /8 9 1 /4 EP1CHG 10. n/a n/a Carpet gripper 12/pkg. EP1CG n/a n/a EP3 Coat Hook Straight 5/pkg. 1 /8 1 3 /8 2 3 /8 EP3MMCH (B/P) 94. n/a n/a EP3 Coat Hook Postless End 5/pkg. 1 3 /8 1 /8 2 3 /8 EP3MMCHPE (R/L)(B/P) 94. n/a n/a Example: EP1CH, 117 EP1CH Coat hook 117 Soft Grey trim Specify trim color. Coat Hook and Coat Hanger available only in Dark Neutral, Medium Grey, Soft Grey or Taupe. NOTE: EP1 & EP2 Panels and components are available in legacy colors only. Coat hanger: A plastic coat hanger available to hang on coat hook. EP1 Coat hook: Molded plastic hook hangs over EP1 panels to hold coats and hangers. Coat hook must hang over staight post location if being used w/ep3 panels. Carpet gripper:12 per package. EP3 Coat hook: Aluminum coat hook attaches to any exposed vertical slot. There are two versions. The straight version will work on any vertical slot except for those on an inside corner. The postless end version is handed and extends beyond the edge of a panel with a postless end. Hand is determined by which side of the panel the coat hook is installed on while facing the panel. Available in two colors; Black (B) or Matte Aluminum (P). 84

85 Worksurface loading/support System applications information Support must be installed for every four feet of width. As indicated, 5 worksurfaces require three supports; two panels are required to install the center support. The applications shown in the table emphasize the fundamentals of worksurface loading and support. As long as these criteria are met, supports can be interchanged.* Supporting drawer pedestals can replace only one support. Adjacent worksurface-hung drawer units require support on both sides of the drawers. Depth of stretchered worksurfaces must be equal to or less than side panel widths. Stretchered worksurfaces should be used where heavy loading is anticipated. Cantilevers cannot be used as primary support for 36 deep surfaces or 30 deep surfaces wider than 6. The front edge of 30 deep surfaces should not be loaded in excess of 180 pounds. Worksurface Sizes To Be Supported EB1C20(L/R) Cantilever-C Support Options For Worksurfaces EB1SR(S/L) Stretcher Rail-S 24 Deep Supporting Pedestal 30 Deep Supporting Pedestal 2 Wx20 D 200 lbs. 2C 200 lbs. 2S N/A N/A 2 Wx24 D 200 lbs. 2C 200 lbs. 2S +1 Support N/A 30 Wx20 D 200 lbs. 2C 200 lbs. 2S N/A N/A 30 Wx24 D 200 lbs. 2C 200 lbs. 2S +1 Support N/A 30 Wx30 D 200 lbs. 2C 200 lbs. 2S +1 Support 3 Wx20 D 200 lbs. 2C 200 lbs. 2S N/A N/A 3 Wx24 D 200 lbs. 2C 200 lbs. 2S +1 Support N/A 3 Wx30 D 200 lbs. 2C 200 lbs. 2S +1 Support 42 Wx20 D 200 lbs. 2C 200 lbs. 2S N/A N/A 42 Wx24 D 200 lbs. 2C 200 lbs. 2S +1 Support N/A 42 Wx30 D 200 lbs. 2C 200 lbs. 2S +1 Support 4 Wx20 D 216 lbs. 2C 216 lbs. 2S N/A N/A 4 Wx24 D 216 lbs. 2C 216 lbs. 2S +1 Support N/A 4 Wx30 D 216 lbs. 2C 216 lbs. 2S +1 Support 54 Wx20 D 243 lbs. 3C 243 lbs. 2S/1C N/A N/A 54 Wx24 D 243 lbs. 3C 243 lbs. 2S/1C +2 Supports N/A 54 Wx30 D 243 lbs. 3C 243 lbs. 2S/1C +2 Supports 5 Wx20 D 270 lbs. 3C 270 lbs. 2S/1C N/A N/A 5 Wx24 D 270 lbs. 3C 270 lbs. 2S/1C +2 Supports N/A 5 Wx30 D 270 lbs. 3C 270 lbs. 2S/1C +2 Supports 66 Wx20 D 297 lbs. 3C 297 lbs. 2S/1C N/A N/A 66 Wx24 D 297 lbs. 3C 297 lbs. 2S/1C +2 Supports N/A 66 Wx30 D 297 lbs. 3C 297 lbs. 2S/1C +2 Supports 6 Wx20 D 324 lbs. 3C 324 lbs. 2S/1C N/A N/A 6 Wx24 D 324 lbs. 3C 324 lbs. 2S/1C +2 Supports N/A 6 Wx30 D 324 lbs. 3C 324 lbs. 2S/1C +2 Supports 78 Wx20 D 351 lbs. 3C 351 lbs. 2S/1C N/A N/A 78 Wx24 D 351 lbs. 3C 351 lbs. 2S/1C +2 Supports N/A 7 Wx20 D 378 lbs. 3C 378 lbs. 2S/1C N/A N/A 7 Wx24 D 378 lbs. 3C 378 lbs. 2S/1C +2 Supports N/A 7 Wx30 D 378 lbs. 2S/1C +2 Supports 90 Wx20 D 405 lbs. 3C 405 lbs. 2S/1C N/A N/A 90 Wx24 D 405 lbs. 3C 405 lbs. 2S/1C +2 Supports N/A 8 Wx20 D 432 lbs. 3C 432 lbs. 2S/1C N/A N/A 8 Wx24 D 432 lbs. 3C 432 lbs. 2S/1C +2 Supports N/A 8 Wx30 D 432 lbs. 2S/2C +2 Supports 9 Wx20 D 486 lbs. 4C 486 lbs. 2S/2C N/A N/A 9 Wx24 D 486 lbs. 4C 486 lbs. 2S/2C +3 Supports N/A 9 Wx30 D 486 lbs. 2S/2C +3 Supports 10 Wx20 D 540 lbs. 4C 540 lbs. 2S/2C N/A N/A 10 Wx24 D 540 lbs. 4C 540 lbs. 2S/2C +3 Supports N/A 10 Wx30 D 540 lbs. 2S/2C +3 Supports Weights listed are the BIFMA* functional load requirements for panel hung worksurface loading. If loads larger than these listed are anticipated, approval from Knoll, Inc. is required. INSTALLATIONS WHICH VIOLATE THESE REQUIREMENTS WILL NOT BE COVERED BY THE KNOLL, INC. LIMITED WARRANTY. *Business Institutional Furniture Manufacturers Association. Worksurfaces and Tables 85

86 General information General Information 120 degree worksurface Top surface available in standard laminates and wood veneers. For a complete list of color offering consult the Finishes page at the beginning of the price list. Laminate worksurfaces are available in two edge treatments: 2mm thick edgeband and 1 ergonomic front edge with 2mm side and back edges. Veneer surfaces are produced in natural wood patterns using techgrain wood to ensure consistency and then finished to color. Surface edging is of lumber band, finished to color. Due to the nature of wood veneer, a desk pad is recommended for primary writing surfaces. Edge grommets, when specified, are in a rear, centered location and are available in black only for shipments after December 31, Corner worksurfaces provide two edge grommets. EW2 and EW3 provide additional half grommets on either end to provide a full grommet when two tops meet. The half grommet also allows for cord management by itself when it is wrapped by panels and not adjacent to other worksurfaces. Underside of all 24 deep and deeper rectangular worksurfaces is predrilled for mounting of the pedestals and support bracketry. The front edge of 30 deep cantilevered surfaces should not be loaded in excess of 180 pounds. Surface thickness is 1 1 /4. EW1 worksurfaces are designed to provide a 3 /8 cable management gap between the back edge of the worksurface and wall panel. EW2 and EW3 worksurfaces are flush against the supporting panel. D and P tops are actual depth plus 1 1 /2 to cover two posts and may not be panel wrapped. This allows a stretcher rail to support the flat end without being visually obtrusive. Adjacent worksurfaces should be specified so as not to cover a post where a D or P top may be used. Tables bases (columns, hubs, legs and stretchers) are painted or polished chrome. All tables are shipped knocked-down (KD). Some EW1 worksurfaces may be ordered with cantilevers/supporting hardware by adding a C to the end of the pattern number and the appropriate list price upcharge as listed in the application notes. Worksurfaces up to 48 inches wide will include one left hand and one right hand cantilever. Worksurfaces from 48 inches to 96 inches wide will include one right hand cantilever and two left hand cantilevers. Worksurfaces greater than 96 inches wide will include one right hand cantilever and three left hand cantilevers. The additional left hand cantilevers are required for center support on tops greater than 48 inches wide. 36 inch deep worksurfaces are not available with support hardware included. Extended one end and extended both ends tops are not available with support hardware included. Cascade Edge Please Note: Cascade Edge worksurfaces are wrapped with a vinyl sheet that is heated and pressed around an MDF substrate. Vinyl is more susceptible to denting, impact, tearing and marring than conventional high pressure laminate and should be handled with care. Do not drag worksurfaces across any flooring surface. Treat Cascade Edge worksurfaces like veneer worksurfaces for optimum performance under normal conditions. Cascade Edge worksurfaces come with a 5 year warranty that covers defects in workmanship and materials. This warranty does not cover damage occurring during or after installation. 2mm edge depth is actual minus 3 /8 at the back for a cord drop 2mm edge depth is actual, back of worksurface is flush with panel 24mm front edge 2mm back and side, back of worksurface is flush with panel Cascade Edge Seamless eased front edge, depth is actual minus 3 /8 at the back for a cord drop Cascade Edge profile 86

87 This page intentionally left blank

88 General information Woodgrain laminate direction 88

89 General Information 120 degree Worksurfaces Woodgrain laminate direction Worksurfaces and Tables 89

90 EW1 Worksurfaces Rectangular 20 and 24 deep description w d pattern no. 2mm edge woodgrain edge 20 D Rectangular EW12420G $174. $191. $ EW13020G EW13620G EW14220G EW14820G EW15420G EW16020G EW16620G EW17220G EW17820G EW18420G EW19020G EW19620G EW110220G EW110820G EW111420G EW112020G D Rectangular EW12424G EW13024G EW13624G EW14224G EW14824G EW15424G EW16024G EW16624G EW17224G EW17824G EW18424G EW19024G EW19624G EW110224G EW110824G EW111424G EW112024G metal edge Example: EW17220G, 117, 117 EW1 top only 72 Width in inches 20 Depth in inches G w/grommet 117 Soft Grey laminage 117 Soft Grey edge Specify surface and edge color. Note: If an edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page 99. Extended worksurfaces not available with support hardware included. Note: For woodgrain direction see page Pattern numbers listed above are for worksurface only. See page 85 for Worksurface Loading and Support Application Information. For cantilevered worksurfaces, please add a C to the end of the pattern number and add $50 to the list price. Worksurfaces up to 48 inches wide will include one left hand and one right hand cantilever. Worksurfaces greater than 48 inches wide will include two left hand cantilevers and one right hand cantilever. The additional left hand cantilever is required for additional center support on tops spanning a distance greater than 48 inches. A center support must be used with a54 wide or larger worksurface. Note: Extended one end add E and $20. Extended both ends add EE and $40. ( EE not available on 120.) Extended tops are not available with support hardware included.

91 EW1 Worksurfaces Rectangular 30 and 36 deep description w d pattern no. 2mm edge woodgrain edge 30 D Rectangular EW12430G $226. $249. $ EW13030G EW13630G EW14230G EW14830G EW15430G EW16030G EW16630G EW17230G EW17830G EW18430G EW19030G EW19630G EW110230G EW110830G EW111430G EW112030G metal edge Worksurfaces and Tables 36 D Rectangular EW14836G EW15436G EW16036G EW16636G EW17236G EW17836G EW18436G EW19036G EW19636G EW110236G EW110836G EW111436G EW112036G Example: EW17230G, 117, 117 EW1 top only 72 Width in inches 30 Depth in inches G w/grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Any support required must be ordered separately (including floorstanding pedestals, etc.). Note: If an edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page 126. Extended worksurfaces are not available with support hardware included. Note: For woodgrain direction see page 88. Pattern numbers listed above are for worksurface only. See page 126 for Worksurface Loading and Support Application Information.For cantilevered worksurfaces, please add a C to the end of the pattern number and add $50 to the list price. Worksurfaces up to 48 inches wide will include one left hand and one right hand cantilever. Worksurfaces greater than 48 inches wide will include two left hand cantilevers and one right hand cantilever. The additional left hand cantilever is required for additional center support on tops spanning a distance greater than 48 inches. 36 deep top cannot be used with cantilevers. Must be mounted with 36 or longer stretcher rails. Use pedestal or freestanding end panel for intermediate support under 72 or larger worksurfaces (36 depth only). A center support must be used with a54 wide or larger worksurfaces. Note: Extended one end add E and $20. Extened both ends add EE and $40. ( EE not available on 120.) Extended tops and 36 deep tops are not available with support hardware included. 91

92 EW1 Worksurfaces Corner description A B C pattern no. 2mm edge woodgrain edge Corner tops EW1C3620G $413. $454. $ EW1C3624G EW1C3630G EW1C4220G EW1C4224G EW1C4230G EW1C4820G EW1C4824G EW1C4830G Corner top with cutout EW1C4824KG metal edge Curved corner tops EW1CC3624G EW1CC4224G EW1CC4824G EW1CC6024G Corner top with 2 different returns EW1C362430G EW1C363024G EW1C422430G EW1C423024G EW1C482430G EW1C483024G Split corner tops EW1SC3624GC 1,351. 1,486. 1, EW1SC4224GC 1,383. 1,522. 1, EW1SC4230GC 1,408. 1,549. 1, EW1SC4824GC 1,464. 1,611. 1, EW1SC4830GC 1,560. 1,715. 1,871. Applicatin Notes Example: EW1C482430G, 117, 117 EW1 top only C Corner surface 48 Width 24 Left return depth 30 Right return depth G grommets 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Note: If and edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page 126. Note: For woodgrain direction see page 88. When wood grain or brushed laminates are specified on corner worksurfaces, one of three grain direction options must be specified. Insert the desired grain direction option (L,R or D) after the laminate finish code. Please add $25 to the list price for diagonal grain (D) selection. A return panel may not be used next to corner worksurfaces, as they cover both posts for a smooth transition with adjacent rectangular worksurfaces. All supports must be ordered seperately. A panel to worksurface bracket must be ordered to support the back corner of a corner worksurface. Cantilevers are included with split corner worksurfaces. For cantilever worksurfaces, add a C to the end of the pattern number and add $50 to the list price. Cantilever worksurfaces include a left hand and right hand cantilever and a left hand panel to worksurface bracket to support the back corner. 92

93 EW1 Worksurfaces Blended Corner&Peninsula description A B C D pattern no. 2mm edge woodgrain edge Blended corner EW1BS3660S( )G $563. $619. $ EW1BS3672S( )G EW1BS4860S( )G EW1BS4860D( )G EW1BS4866S( )G EW1BS4866D( )G EW1BS4872S( )G EW1BS4872D( )G EW1BS6036S( )G EW1BS6048S( )G EW1BS6048D( )G EW1BS6648S( )G EW1BS6648D( )G EW1BS7236S( )G EW1BS7248S( )G EW1BS7248D( )G EW1BD4860S( )G EW1BD4866S( )G EW1BD4872S( )G EW1BD6048S( )G EW1BD6648S( )G EW1BD7248S( )G metal edge Worksurfaces and Tables Blended peninsula (left handed shown) EW1BP6048S(R/L) EW1BP7248S(R/L) EW1BP7248D(R/L) EW1BP7848S(R/L) EW1BP7848D(R/L) EW1BP8448S(R/L) EW1BP8448D(R/L) Example: EW1BS3672SLG, 117, 117 EW1B Blended worksurface S 24 left depth left width right width S 24 right width L Left side post covered G Grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. All support bracketry must be ordered separately. Note: If and edge grommet is not desired remove the G and deduct $20. Note: For woodgrain direction see page 88. Blended worksurfaces are designed to take the place of two adjacent worksurfaces by blending them into one top. The front of the worksurface is curved to provide a smooth transition to the next attached worksurface. Blended worksurfaces are handed and may or may not cover a post on either or both sides. Hand is determined from the seated position. Option suffixes for Blended corners are as follows: X=No posts covered L=Left side post covered R=Right side post covered B=Both sides posts covered Blended peninsulas are handed and always cover one post. Hand is determined from seated position. Rounded end is 30 deep. Depth options are as follows: S=24 deep D=30 deep Center support must be used for all surfaces which exceed 48 in length. 93

94 EW2 Worksurfaces Rectangular 20 and 24 deep description w d pattern no. 2mm edge woodgrain edge 20 D Rectangular EW22420G $174. $191. $ EW23020G EW23620G EW24220G EW24820G EW25420G EW26020G EW26620G EW27220G EW27820G EW28420G EW29020G EW29620G EW210220G EW210820G EW211420G EW212020G D Rectangular EW22424G EW23024G EW23624G EW24224G EW24824G EW25424G EW26024G EW26624G EW27224G EW27824G EW28424G EW29024G EW29624G EW210224G EW210824G EW211424G EW212024G metal edge Specificaiton Information Example: EW27220G, 117, 117 EW2 top only 72 Width in inches 20 Depth in inches G w/grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Any support required must be ordered separately (including cantilevers, floorstanding pedestals, etc.).note: If an edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page126. Pattern numbers listed above are for worksurface only. All support must be ordered seperately. See page 85 for Worksurface Loading and Support Application Information. A center support must be used with a54 wide or larger worksurface. Note: Extended one end add E and $20. Extended both ends add EE and $40. ( EE not available on 120.) Note: For woodgrain direction see page

95 EW2 Worksurfaces Rectangular 30 and 36 deep description w d pattern no. 2mm edge woodgrain edge 30 D Rectangular EW22430G $226. $249. $ EW23030G EW23630G EW24230G EW24830G EW25430G EW26030G EW26630G EW27230G EW27830G EW28430G EW29030G EW29630G EW210230G EW210830G EW211430G EW212030G metal edge Worksurfaces and Tables 36 D Rectangular EW24836G EW25436G EW26036G EW26636G EW27236G EW27836G EW28436G EW29036G EW29636G EW210236G EW210836G EW211436G EW212036G Example: EW27230G, 117, 117 EW2 top only 72 Width in inches 30 Depth in inches G w/grommets 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Any support required must be ordered separately (including floorstanding pedestals, etc.).note: If an edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page126. Note: For woodgrain direction see page Pattern numbers listed above are for worksurface only. All support hardware must be ordered seperately. See page 85 for Worksurface Loading and Support Application Information. 36 deep top may not be used with cantilevers. Must be mounted with 36 or longer stretcher rails. Use pedestal or freestanding end panel for intermediate support under 72 or larger worksurfaces (36 depth only). A center support must be used with a54 wide or larger worksurface. Note: Extended one end add E and $20. Extended both ends add EE and $40 ( EE not available on 120.)

96 EW2 Worksurfaces Corner description A B C pattern no. 2mm edge woodgrain edge Corner tops EW2C3620G $413. $454. $ EW2C3624G EW2C3630G EW2C4220G EW2C4224G EW2C4230G EW2C4820G EW2C4824G EW2C4830G Curved corner tops EW2CC3624G EW2CC4224G EW2CC4824G EW2CC6024G metal edge Corner top with 2 different returns EW2C362430G EW2C363024G EW2C422430G EW2C423024G EW2C482430G EW2C483024G Split corner tops EW2SC3624GC 1,351. 1,486. 1, EW2SC4224GC 1,383. 1,522. 1, EW2SC4230GC 1,408. 1,549. 1, EW2SC4824GC 1,464. 1,611. 1, EW2SC4830GC 1,560. 1,716. 1,872. Example: EW2C4830G, 117, 117 EW2 top only C Corner worksurface 48 Width 30 Depth G Grommets 117 Soft Grey laminate 117 Soft Grey edge Specify surface, and edge color.note: If and edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page126. Note: For woodgrain direction see page 88. When wood grain or brushed laminates are specified on corner worksurfaces, one of three grain direction options must be specified. Insert the desired grain direction option (L,R or D) after the laminate finish code. Please add $25 to the list price for diagonal grain (D) selection. A return panel may not be used next to corner worksurfaces, as they cover both posts for a smooth transition with adjacent rectangular worksurfaces. All supporting hardware, including a panel to worksurface bracket to support the back corner, must be ordered seperately. Cantilevers are included with split corner worksurfaces only. 96

97 EW2 Worksurfaces Blended Corner&Peninsula description A B C D pattern no. 2mm edge woodgrain edge Blended corner EW2BS3660S( )G $563. $619. $ EW2BS3672S( )G EW2BS4860S( )G EW2BS4860D( )G EW2BS4866S( )G EW2BS4866D( )G EW2BS4872S( )G EW2BS4872D( )G EW2BS6036S( )G EW2BS6048S( )G EW2BS6048D( )G EW2BS6648S( )G EW2BS6648D( )G EW2BS7236S( )G EW2BS7248S( )G EW2BS7248D( )G EW2BD4860S( )G EW2BD4866S( )G EW2BD4872S( )G EW2BD6048S( )G EW2BD6648S( )G EW2BD7248S( )G metal edge Worksurfaces and Tables Blended peninsula (left handed shown) EW2BP6048S(R/L) EW2BP7248S(R/L) EW2BP7248D(R/L) EW2BP7848S(R/L) EW2BP7848D(R/L) EW2BP8448S(R/L) EW2BP8448D(R/L) Example: EW2BS3672SLG, 117, 117 EW2B Blended worksurface S 24 left depth left width right width S 24 right depth L Left side post covered G Grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface edge color. All support bracketry must be ordered separately. Note: If an edge grommet is not desired, remove the G and deduct $20. Note: For woodgrain direction see page Blended worksurfaces are designed to take the place of two adjacent worksurfaces by blending them into one top. The front of the worksurface is curved to provide a smooth transition to the next attached worksurface. Blended worksurfaces are handed and may or may not cover a post on either or both sides. Hand is determined from the seated position. Option suffixes for Blended corners are as follows: X=No posts covered L=Left side post covered R=Right side post covered B=Both sides posts covered Blended peninsulas are handed and always cover one post. Hand is determined from seated position. Rounded end is 30 deep. Blended peninsulas do not come with grommets. Due to this, the worksurface meeting the c side will have a one-half grommet where the return meets the peninsula. Depth options are as follows: S=24 deep D=30 deep Center support must be used for all surfaces which exceed 48 in length.

98 EW3 Worksurfaces Rectangular 20 and 24 deep description w d pattern no. list price 20 D Rectangular EW32420G $ EW33020G EW33620G EW34220G EW34820G EW35420G EW36020G EW36620G EW37220G EW37820G EW38420G EW39020G EW39620G EW310220G EW310820G EW311420G EW312020G D Rectangular EW32424G EW33024G EW33624G EW34224G EW34824G EW35424G EW36024G EW36624G EW37224G EW37824G EW38424G EW39024G EW39624G EW310224G EW310824G EW311424G EW312024G 691. Example: EW37220G, 117, 117 EW3 top only 72 Width in inches 20 Depth in inches G w/grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Any support required must be ordered separately (including floorstanding pedestals, etc.).note: If an edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page126. Pattern numbers listed above are for worksurface only. All support hardware must be ordered seperately. See page 85 for Worksurface Loading and Support Application Information. A center support must be used with a54 wide or larger worksurface. Note: Entended one end add E and $20. Extended both ends add EE and $40. ( EE not available on 120.) Note: For woodgrain direction see page

99 EW3 Worksurfaces Rectangular 30 and 36 deep description w d pattern no. list price 30 D Rectangular EW32430G $ EW33030G EW33630G EW34230G EW34830G EW35430G EW36030G EW36630G EW37230G EW37830G EW38430G EW39030G EW39630G EW310230G EW310830G EW311430G EW312030G 963. Worksurfaces and Tables 36 D Rectangular EW34836G EW35436G EW36036G EW36636G EW37236G EW37836G EW38436G EW39036G EW39636G EW310236G EW310836G EW311436G EW312036G 1,000. Example: EW37230G, 117, 117 EW3 top only 72 Width in inches 30 Depth in inches G w/grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Any support required must be ordered separately (including floorstanding pedestals, etc.).note: If an edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page126. Note: For woodgrain direction see page Pattern numbers listed above are for worksurface only. All support hardware must be ordered seperately. See page 85 for Worksurface Loading and Support Application Information. 36 deep top may not be used with cantilevers. Must be mounted with 36 or longer stretcher rails. Use pedestal or freestanding end panel for intermediate support under 72 or larger worksurfaces (36 depth only). A center support must be used with a54 wide or larger worksurface. Note: Extended one end add E and $20. Extended both ends add EE and $40. ( EE not available on 120.)

100 EW3 Worksurfaces Corner description A B C pattern no. list price Corner tops EW3C3620G $ EW3C3624G EW3C3630G EW3C4220G EW3C4224G EW3C4230G EW3C4820G EW3C4824G EW3C4830G 820. Curved corner tops EW3CC3624G EW3CC4224G EW3CC4824G EW3CC6024G 985. Corner top with 2 different returns EW3C362430G EW3C363024G EW3C422430G EW3C423024G EW3C482430G EW3C483024G 891. Split corner tops EW3SC3624GC 1, EW3SC4224GC 1, EW3SC4230GC 1, EW3SC4824GC 1, EW3SC4830GC 1,619. Example: EW3CC4824G, 117, 117 EW3 top only CC Curved corner 48 Width 24 Depth G Grommets 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color.note: If and edge grommet is not desired remove the G and deduct $20. Worksurface cable baskets may be ordered separately. See page126. Note: For woodgrain direction see page 88. When wood grain or brushed laminates are specified on corner worksurfaces, one of three grain direction options must be specified. Insert the desired grain direction option (L,R or D) after the laminate finish code. Please add $25 to the list price for diagonal grain (D) selection. A return panel may not be used next to corner worksurfaces, as they cover both posts for a smooth transition with adjacent rectangular worksurfaces. All supporting hardware, including a panel to worksurface bracket for the back corner, must be ordered seperately. Cantilevers are included with split corner worksurfaces only. 100

101 EW3 Worksurfaces Blended Corner&Peninsula description A B C D pattern no. list price Blended corners EW3BS3660S( )G $ EW3BS3672S( )G EW3BS4860S( )G EW3BS4860D( )G EW3BS4866S( )G EW3BS4866D( )G EW3BS4872S( )G EW3BS4872D( )G EW3BS6036S( )G EW3BS6048S( )G EW3BS6048D( )G EW3BS6648S( )G EW3BS6648D( )G EW3BS7236S( )G EW3BS7248S( )G EW3BS7248D( )G EW3BD4860S( )G EW3BD4866S( )G EW3BD4872S( )G EW3BD6048S( )G EW3BD6648S( )G EW3BD7248S( )G 908. Worksurfaces and Tables Blended peninsula (left handed shown) EW3BP6048S(R/L) EW3BP7248D(R/L) 899. Example: EW3BS3672SLG, 117, 117 EW3B Blended worksurface S 24 left depth left width right width S 24 right depth L Left side post covered G Grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. All support bracketry must be ordered separately. Note: If an edge grommet is not desired, remove the G and deduct $20. Note: For woodgrain direction see page Blended worksurfaces are designed to take the place of two adjacent worksurfaces by blending them into one top. The front of the worksurface is curved to provide a smooth transition to the next attached worksurface. Blended worksurfaces are handed and may or may not cover a post on either or both sides. Hand is determined from the seated position. Option suffixes for Blended corners are as follows: X=No posts covered L=Left side post covered R=Right side post covered B=Both sides posts covered Blended peninsulas are handed and always cover one post. Hand is determined from seated position. Rounded end is 30 deep. Blended peninsulas do not come with grommets. Due to this, the worksurface meeting the c side will have a one-half grommet where the return meets the peninsula. Depth options are as follows: S=24 deep D=30 deep Center support must be used for all surfaces which exceed 48 in length.

102 Worksurface, blended double corner, curved cluster, corner round EW1, EW2 and EW3 profiles description A B C pattern no. Standard edge woodgrain edge Blended double corner EW1BC9648G $753. $829. $ EW2BC9648G EW3BC9648G 978. n/a n/a metal edge 135 Curved cluster EW G EW G EW G 861. n/a n/a EW G EW G EW G 1,075. n/a n/a EW G ,043. 1, EW G ,043. 1, EW G 1,232. n/a n/a 135 Curved cluster center core 36 EW1135C EW1135C EW1135C Corner-round worksurface 24 EW1CR EW2CR EW3CR n/a n/a 30 EW1CR EW2CR EW3CR n/a n/a Double corner worksurface is designed to take the place of two adjacent corners by combining then into one top. 48 deep sides are designed to cover a post and cannot be panel wrapped. Example: EW1BC9648G, 117, 117 EW1BC Blened double corner 96 Width 48 Depth G Grommet 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Support bracketry must be ordered separately. Note: If an edge grommet is not desired, remove the G and deduct $20. Note: For woodgrain direction see page 88. Corner round worksurface is for use in outside 90-degree configurations only and is used to transition two adjacent worksurfaces. Worksurfaces meeting either side of the corner-round worksurface must be extended on that end to avoid a gap between worksurfaces. Curved cluster worksurface is used in 135-degree planning configurations. 102

103 Worksurfaces, D, P+9 EW1, EW2 and EW3 profiles description type w d pattern no. standard edge woodgrain edge D tops EW1D6030 $364. $401. $ EW2D EW3D n/a n/a EW1D EW2D EW1D EW2D EW1D EW2D EW1D EW2D P+9 tops ( 9 shown) EW1(9/P) EW2(9/P) EW1(9/P) EW2(9/P) EW1(9/P) EW2(9/P) EW1(9/P) EW2(9/P) metal edge Worksurfaces and Tables Example: EW1P7230C, 117, 117, 117 EW1 Gen 1 worksurface P P top 72 Width 30 Depth C Supports included 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Specify hardware color for bases and stretcher rails. Note: P and D worksurfaces cannot be panel wrapped. Column bases and stretcher rails must be ordered separately. See page 104. Note: For woodgrain direction see page 88. Designed for use as primary worksurfaces and for conferencing in small groups. To specify an EW1 D, P or 9 top with support hardware (fixed-height column and stretcher rail) included add a C to the end of the pattern number and add $200 to the list price. 84 wide D, P and 9 worksurfaces include a V support bar mounted on the underside for additional stability. 103

104 Worksurfaces, D, P+9 Column base and stretcher rails description type pattern no. P1 P2 P3 Column Bases Adjustable Height EB1ACOL $264. $280. $291. Support Column (26 to 30 ) Fixed Height Support Column (27 3 /4 ) EB1FCOL Stretcher rails 24,30 and 36 widths EB1SRS ,48 and 60 widths EB1SRL Pkg. of 10 24,30 and 36 widths EB1SRS Pkg. Of 10 42,48 and 60 widths EB1SRL Example: EW1P7230C, 117, 117, 117 EW1 Gen 1 worksurface P P top 72 Width 30 Depth C Supports included 117 Soft Grey laminate 117 Soft Grey edge Specify surface and edge color. Specify hardware color for bases and stretcher rails. Note: P and D worksurfaces cannot be panel wrapped. Column bases and stretcher rails must be ordered separately Designed for use as primary worksurfaces and for conferencing in small groups. To specify an EW1 D, P or 9 top with support hardware (fixed-height column and stretcher rail) included add a C to the end of the pattern number and add $200 to the list price. 84 wide D, P and 9 worksurfaces include a V support bar mounted on the underside for additional stability. 104

105 Worksurface, half round EW1, EW2 and EW3 profiles description w d pattern no. P1 P2 P3 Half round worksurface 48 without notch 30 EW1HR4830 $529. $545. $ with round notch 30 EW1HR4830N with square notch 30 EW1HR4830NK without notch 30 EW2HR with round notch 30 EW2HR4830N with square notch 30 EW2HR4830NK without notch 30 EW3HR with round notch 30 EW3HR4830N with square notch 30 EW3HR4830NK without notch 36 EW1HR with round notch 36 EW1HR6036N with square notch 36 EW1HR6036NK without notch 36 EW2HR with round notch 36 EW2HR6036N with square notch 36 EW2HR6036NK without notch 36 EW3HR with round notch 36 EW3HR6036N with square notch 36 EW3HR6036NK Worksurfaces and Tables Example: EW1HR4830N, 117, 117, 117 EW1HR Half round worksurface 48 Width 30 Depth N Notched for post 117 Soft Grey laminate 117 Soft Grey edge 117 Soft Grey column Specify surface, edge and hardwar trim color. Note: For woodgrain direction see page 88. Half round worksurfaces are designed for use as shared reference areas and for conferencing in small groups. 48 wide half rounds attach to any 48 width of panels. 60 wide half rounds attach to any 60 width of panels. Half rounds without notches attach to panels by means of a stretcher rail and are supported by column bases, available in standard trim colors. Column bases and stretcher rails are supplied. Column is fixed height. Round notch N and square notch NK include splice plates and column; do not require nor include stretcher rail for support. Wood Grain and Metal edge bands: When specifying a top with a wood grain edge band add $25 to the standard list price. When specifying a top with a metal edge band add $50 to the standard list price. 105

106 Cascade Edge Worksurfaces Rectangular description w d pattern no. Solid Woodgrain 24 D Rectangular ECE1R2424N $171. $ ECE1R3024N ECE1R3624N ECE1R4224N ECE1R4824N ECE1R5424N ECE1R6024N ECE1R6624N ECE1R7224N ECE1R7824N ECE1R8424N ECE1R9024N ECE1R9624N D Rectangular ECE1R2430N ECE1R3030N ECE1R3630N ECE1R4230N ECE1R4830N ECE1R5430N ECE1R6030N ECE1R6630N ECE1R7230N ECE1R7830N ECE1R8430N ECE1R9030N ECE1R9630N Sample ECE1R1212G Example: ECE1R4824N,118 ECE1 Cascade Edge worksurface R Rectangular 48 Width 24 Depth N No grommet 118 Bright White finish Available finishes: Solid: 114 Folkstone Grey 117 Soft Grey 118 Bright White 119 Pumice Woodgrain: 124 Medium Cherry 125 Natural Maple 126 Natural Cherry 127 Walnut Center-Located Edge Grommet. To specify, replace the N suffix from the pattern number with G. Add $20. Note: Extended one end add E with no upcharge. Extended both ends EE is not available on Cascade worksurfaces. Cascade edge profile. Bold line on image represents Cascade Edge detail. All support hardware must be ordered separately. 106

107 Cascade Edge Worksurfaces Blended D description A B C pattern no. Solid Woodgrain Blended D right hand shown ECE1BD6648S(L/R) $695. $ ECE1BD6648D(L/R) ECE1BD7248S(L/R) ECE1BD7248D(L/R) ECE1BD7848S(L/R) ECE1BD7848D(L/R) ECE1BD8448S(L/R) ECE1BD8448D(L/R) ,030. Worksurfaces and Tables Example: ECE1BD7248SL,118 ECE1 Cascade Edge worksurface BD Blended D 72 Width 48 Depth S 24 d return L Extended Left 118 Bright White finish Available finishes: Solid: 114 Folkstone Grey 117 Soft Grey 118 Bright White 119 Pumice Woodgrain: 124 Medium Cherry 125 Natural Maple 126 Natural Cherry 127 Walnut All support hardware must be ordered separately. Cascade edge profile. Bold line on image represents Cascade Edge detail. 107

108 Cascade Edge Worksurfaces Curvilinear corner description A B C pattern no. Solid Woodgrain Curvilinear corner ECE1L3636SSN $430. $ ECE1L4242SSN ECE1L4242SDN ECE1L4242DSN ECE1L4848SSN ECE1L4848SDN ECE1L4848DSN ECE1L4848DDN Example: ECE1L4848SSG,114 ECE1 Cascade Edge worksurface L Curvilinear Corner 48 Width 48 Depth S 24 d, left side S 24 d, right side G Grommet 114 Folkstone Grey finish Available finishes: Solid: 114 Folkstone Grey 117 Soft Grey 118 Bright White 119 Pumice Woodgrain: 124 Medium Cherry 125 Natural Maple 127 Natural Cherry 128 Walnut Note: When wood grain or brushed laminates are specified on Cascade corner worksurfaces with two A sides of equal length, one of three grain direction options must be specified. Insert the desired grain direction option (L,R or D) after the laminate code. Please add $25 to the list price for diagonal grain (D) selection. Center-Located Edge Grommet. To specify, replace the N suffix from the pattern number with G. Add $40. Cascade edge profile. Bold line on image represents Cascade Edge detail. All support hardward must be ordered separately including rear corner support. 108

109 Cascade Edge Worksurfaces Blended L description B C A D pattern no. Solid Woodgrain Blended L ECE1L4260SS( )N $712. $ ECE1L4266SS( )N ECE1L4272SS( )N ECE1L4278SS( )N ECE1L4860SS( )N ECE1L4860DS( )N ECE1L4866SS( )N ECE1L4866SD( )N ECE1L4866DS( )N ECE1L4872SS( )N ECE1L4872SD( )N ECE1L4872DS( )N ECE1L4878SS( )N ECE1L4884SS( )N , ECE1L4860SD( )N ECE1L6042SS( )N ECE1L6048SS( )N ECE1L6048SD( )N ECE1L6048DS( )N ECE1L6642SS( )N ECE1L6648SS( )N ECE1L6648SD( )N ECE1L6648DS( )N ECE1L7242SS( )N ECE1L7248SS( )N ECE1L7248SD( )N ECE1L7248DS( )N ECE1L7842SS( )N ECE1L7848SS( )N ECE1L8448SS( )N ,104. Worksurfaces and Tables Example: ECE1L4872SDXG,114 ECE1 Cascade Edge worksurface L Blended L 48 Width 72 Depth S 24 d, left side D 30 d, right side X No posts covered G Grommet 114 Folkstone Grey finish Available finishes: Solid: 114 Folkstone Grey 117 Soft Grey 118 Bright White 119 Pumice Woodgrain: 124 Medium Cherry 125 Natural Maple 126 Natural Cherry 127 Walnut All support hardware must be ordered separately. Center-Located Edge Grommet. To Specify, replace the N suffix from the pattern number with G. Add $40. L worksurfaces are handed and may or may not cover a post on either or both sides. Hand is determined from the seated position. Option suffixes for blended corners are as follows: X No posts covered L Left side post covered R Right side post covered B Both side post covered Cascade edge profile. Bold line on image represents Cascade Edge detail. 109

110 Cascade Edge Worksurfaces Half round and Corner round description w d pattern no. Solid Woodgrain Half Round ECE1H4818P $371. $ ECE1H4818PC ECE1H4818PE ECE1H6024P ECE1H6024PC ECE1H6024PE LH / RH Corner Round ECE1CR24L/R Notched Corner Round ECE1CR24N Example: ECE1H4818P, 117 ECE1 Cascade Edge worksurface H Half Round 48 Width 18 Depth P Notched for panel 117 Soft grey finish Available finishes: Solid: 114 Folkstone Grey 117 Soft Grey 118 Bright White 119 Pumice Woodgrain: 124 Medium Cherry 125 Natural Maple 126 Natural Cherry 127 Walnut Half Round P= Notched for post PE= Notched for postless end. PC= Notched for post with post cover. Bold line on image represents Cascade Edge detail. Corner Round When utilizing notched corner round, adjacent tops must be extended to cover post at corner round location. Cascade edge profile. All support hardware must be ordered separately. 110

111 Cascade Edge Worksurfaces Wave end and 120 description A B pattern no. Solid Woodgrain Wave End, LH /2 ECE1W363024N $462. $ /2 ECE1W423024N ECE1W483024N / /2 ECE1W723024N Wave End, RH ECE1W362430N ECE1W422430N ECE1W482430N / /2 ECE1W722430N worksurface ECE1W34824G Worksurfaces and Tables Example: ECE1W483024N, 118 ECE1 Cascade edge worksurface W Wave end 48 Width 30 Depth, right side 24 Depth, left side N No grommet 118 Top finish Available finishes: Solid: 114 Folkstone Grey 117 Soft Grey 118 Bright White 119 Pumice Woodgrain: 124 Medium Cherry 125 Natural Maple 126 Natural Cherry 127 Walnut Center-Located Edge Grommet To specify, replace the N suffix from the pattern number with G. Add $ worksurface tops always include grommets. Note: Extended one end add E with no upcharge. Extended both ends EE is not available on Cascade worksurfaces. Cascade edge profile. Bold line on image represents Cascade Edge detail. All support hardware must be ordered separately. 111

112 120 Worksurfaces, transition tops and peninsula tops 2mm edge description top name w return depth d pattern no. list woodgrain edge Worksurface W11L L-18 R EW2W $911. $1,002. $1,092. W11R L-24 R EW2W ,002. 1,092. W1218L L-18 R EW2W ,047. 1,142. W1218R L-24 R EW2W ,047. 1,142. W12L EW2W124824L ,047. 1,142. W12R EW2W124824R ,047. 1,142. W1318L L-18 R EW2W ,002. 1,092. W1318R L-24 R EW2W ,002. 1,092. W13L EW2W134824L ,002. 1,092. W13R EW2W134824R ,002. 1,092. W EW2W W EW2W W5L EW2W54824L W5R EW2W54824R W6L EW2W64824L W6R EW2W64824R W7L EW2W74824L W7R EW2W74824R Transition tops T EW2T T /2 18 EW2T T EW2T T EW2T T EW2T T /2 18 EW2T metal edge Peninsula tops P EW2P P EW2P23836(L/R) Example: EW2W134824L, 118, 118 EW2 120 w/s 2mm edge W13 Worksurface # Side width/return depth L Pedestal on left side 118 Bright White laminate 118 Bright White edge For all tops, specify laminate and edge color. For cantilever, table legs, and column base, specify trim color. Transition and peninsula tops require a column base for support. 120 worksurfaces are not available with woodgrain or brushed laminates unless specified as special product. Refer to the worksurface planning page for worksurface drawings and applications. W7 straight ends are available extended by adding an E to the end of the pattern number and adding $20. W3 top may be extended on either the left or right hand side by adding an EL or ER to the end of the pattern number and adding $20. W3 top may be extended on both ends by adding an EB to the end of the pattern number and adding $40. T2 transition top comes cut to fit against a postless end. If placing against and end with a post, add an N to the end of the pattern number so it is notched for the post. 112

113 120 Worksurfaces, transition tops and peninsula tops 1 ergonomic edge description top name w return depth d pattern no. list price Worksurface W11L L-18 R EW3W $1,094. W11R L-24 R EW3W ,094. W1218L L-18 R EW3W ,117. W1218R L-24 R EW3W ,117. W12L EW3W124824L 1,117. W12R EW3W124824R 1,117. W1318L L-18 R EW3W ,123. W1318R L-24 R EW3W ,123. W13L EW3W134824L 1,094. W13R EW3W134824R 1,094. W EW3W W EW3W W5L EW3W54824L 851. W5R EW3W54824R 851. W6L EW3W64824L 943. W6R EW3W64824R 943. W7L EW3W74824L 957. W7R EW3W74824R 957. Worksurfaces and Tables Transition tops T EW3T T /2 18 EW3T T EW3T T EW3T T EW3T T /2 18 EW3T Peninsula tops P EW3P P EW3P23836(L/R) 491. Example: EW3W134824L, 118, 118 EW3 120 w/s 1 edge W13 Worksurface # Side width/return depth L Pedestal on left side 118 Bright White laminate 118 Bright White edge For all tops, specify laminate and edge color. For cantilever, table legs, and column base, specify trim color. Transition and peninsula tops require a column base for support. 120 worksurfaces are not available with woodgrain or brushed laminates unless specified as special product. 113 Refer to the worksurface planning page for worksurface drawings and applications. W7 straight ends are available extended by adding an E to the end of the pattern number and adding $20. W3 top may be extended on either the left or right hand side by adding an EL or ER to the end of the pattern number and adding $20. W3 top may be extended on both ends by adding an EB to the end of the pattern number and adding $40. T2 transition top comes cut to fit against a postless end. If placing against and end with a post, add an N to the end of the pattern number so it is notched for the post.

114 120 Table tops, worksurface legs and bases description type application w return depth h pattern no. standard edge woodgrain edge Table tops 1 ergonomic edge diamond ET3DT54 $ ergonomic edge large mushroom ET3MT ergonomic edge large triangle ET3TT ergonomic edge small mushroom ET3MT ergonomic edge small triangle ET3TT mm edge diamond ET2DT mm edge large mushroom ET2MT mm edge large triangle ET2TT mm edge small mushroom ET2MT mm edge small triangle ET2TT metal edge P1 P2 P3 Table legs Set of 3 2 legs w/caster 27 ET3LEG3C Set of 3 2 legs w/glides 27 ET3LEG3G Set of 4 2 legs w/casters 27 ET3LEG4C Set of 4 2 legs w/glides 27 ET3LEG4G Column Bases Adjustable Height Support Column (26 to 30 ) EB1ACOL Example: ET2DT54, 118, 118 ET2 120 w/s 2 mm edge DT Diamond top 54 Width 118 Bright White laminage 118 Bright White edge For all tops, specify laminate and edge color. For cantilever, table legs, and column base, specify trim color. Transition and peninsula tops require a column base for support. 120 worksurfaces are not available with woodgrain or brushed laminates unless specified as special product. 114 Refer to the worksurface planning page for worksurface drawings and applications. W7 straight ends are available extended by adding an E to the end of the pattern number and adding $20. W3 top may be extended on either the left or right hand side by adding an EL or ER to the end of the pattern number and adding $20. W3 top may be extended on both ends by adding an EB to the end of the pattern number and adding $40. T2 transition top comes cut to fit against a postless end. If placing against and end with a post, add an N to the end of the pattern number so it is notched for the post.

115 120 Worksurface cantilevers and brackets description top name h pattern no. P1 P2 P3 Cantilevers left hand 60 EB3C18L60 $63. $63. $63. left hand 90 EB3C18L right hand 60 EB3C18R right hand 90 EB3C18R Flat brackets 20 EB1F24 * n/a n/a Worksurfaces and Tables Example: EB3C18L60, 117 EB3C18 Worksurface cantilever L Left hand Soft Grey finish For all tops, specify laminate and edge color. For cantilever, table legs, and column base, specify trim color. Transition and peninsula tops require a column base for support. 115 Refer to the worksurface planning page for worksurface drawings and applications. W7 straight ends are available extended by adding an E to the end of the pattern number and adding $20. W3 top may be extended on either the left or right hand side by adding an EL or ER to the end of the pattern number and adding $20. W3 top may be extended on both ends by adding an EB to the end of the pattern number and adding $40. T2 transition top comes cut to fit against a postless end. If placing against and end with a post, add an N to the end of the pattern number so it is notched for the post.

116 Tables description surface type w d h pattern no. P1 P2 P3 round table Laminate 29 3 / /4 29 ET1RT30 $570. $600. $ / /4 29 ET1RT / /4 29 ET1RT columns - 4 legs 59 3 / /4 29 ET1RT60 1,805. 1,896. 1, legs 47 3 / /4 29 ET1RT48 1,016. 1,067. 1,117. with casters 35 3 / / /8 ET1RT36C square table Laminate ET1ST / /4 29 ET1ST / /4 29 ET1ST / /4 29 ET1ST columns - 4 legs 59 1 / /2 29 ET1ST60 1,718. 1,804. 1, legs 47 3 / /4 29 ET1ST ,013. 1,062. with casters 22 1 / / /8 ET1ST22C rectangular table Laminate 47 3 / /4 29 ET1RCT , / /2 29 ET1RCT3660 1,371. 1,439. 1, / /4 29 ET1RCT3060 1,161. 1,219. 1, / /4 29 ET1RCT3072 1,371. 1,439. 1, / /4 29 ET1RCT3672 1,623. 1,704. 1, / /4 29 ET1RCT4284 2,172. 2,280. 2, columns 95 3 / /4 29 ET1RCT4896 2,801. 2,941. 3,081. Accepts drawers 69 1 / ET1RCT3469 2,061. 2,164. 2,268. Accepts drawers 79 1 / ET1RCT3479 2,061. 2,164. 2,268. Example: ET1RCT3060, 117, 117, 117 ET1RCT Rectangular table 30 Depth 60 Width 117 Soft Grey laminate 117 Soft Grey edge 117 Soft Grey trim Specify surface, trim and hardware trim color. If a polished chrome base is desired, add a P suffix and add $10 to the P1 list price. Tables are only available in EW1 profile. Wood Grain and Metal edge bands: When specifying a top with a wood grain edge band add $25 to the standard list price. When specifying a top with a metal edge band add $50 to the standard list price. Stretchers are used between two or more hubs. Two column tables have one stretcher; four column tables use four stretchers; and six column tables use seven. ET1OT60144 top ships in two sections. Hidden fasteners join sections. 116

117 Tables description surface type w d h pattern no. P1 P2 P3 oval table Laminate 71 3 / /4 29 ET1OT3672 $2,144. $2,251. $2, columns 95 3 / ET1OT4896 3,518. 3,696. 3, columns / ET1OT ,303. 4,517. 4, columns / /4 29 ET1OT ,796. 5,036. 5, columns / /4 29 ET1OT ,263. 6,576. 6,890. Worksurfaces and Tables Example: ET1RCT3060, 117, 117, 117 ET1RCT Rectangular table 30 Depth 60 Width 117 Soft Grey laminate 117 Soft Grey edge 117 Soft Grey trim Specify surface, trim and hardware trim color. If a polished chrome base is desired, add a P suffix and add $10 to the P1 list price. Tables are only available in EW1 profile. Wood Grain and Metal edge bands: When specifying a top with a wood grain edge band add $25 to the standard list price. When specifying a top with a metal edge band add $50 to the standard list price. Stretchers are used between two or more hubs. Two column tables have one stretcher; four column tables use four stretchers; and six column tables use seven. ET1OT60144 top ships in two sections. Hidden fasteners join sections. 117

118 Counter caps, straight Generation 1 and Generation 2 profiles description surface nominal w actual w d h pattern no. P1 P2 P3 counter cap Laminate EW(1/2)1215 $191. $197. $ EW(1/2) EW(1/2) EW(1/2) EW(1/2) EW(1/2) EW(1/2) EW(1/2) EW(1/2) EW(1/2) EW(1/2) EW(1/2) counter cap - extended one end Laminate EW(1/2)1215E EW(1/2)2415E EW(1/2)3015E EW(1/2)3615E EW(1/2)4215E EW(1/2)4815E EW(1/2)6015E EW(1/2)7215E EW(1/2)8415E EW(1/2)9615E EW(1/2)10815E counter cap - extended both ends Laminate EW(1/2)1215EE EW(1/2)2415EE EW(1/2)3015EE EW(1/2)3615EE EW(1/2)4215EE EW(1/2)4815EE EW(1/2)6015EE EW(1/2)7215EE EW(1/2)8415EE EW(1/2)9615EE EW(1/2)10815EE Example: EW16015,117, 117, 117 EW1 Worksurface 60 Width 15 Depth 117 Soft Grey laminate 117 Soft Grey edge 117 Soft Grey cantilever trim Specify surface, trim and cantilever trim color. EW1 Counter caps work with all existing counter caps and are for use on Generation 1 or Generation 2 panels only. Plastic cantilevers are supplied. EW2 counter caps are for use with Genereation 3 panels only. Steel brackets are provided. 118 Counter caps are designed for mounting on top of panels. Straight counter caps overhang both sides of the panel equally. Counter caps fit between posts, appropriate to fit between two taller panels and a duel/triple height connectors. A counter cap extension (E) covers one post. A counter cap extension (EE) covers 2 posts. Steel mounted brackets are supplied. Wood Grain and Metal edge bands: When specifying a top with a wood grain edge band add $25 to the standard list price. When specifying a top with a metal edge band add $50 to the standard list price.

119 Counter caps, corner Generation 1 and Generation 2 profiles description surface w d h pattern no. list price P2 P3 corner counter cap Laminate EW(1/2)CC2415 $268. $279. $ EW(1/2)CC EW(1/2)CC corner counter cap - extended left Laminate EW(1/2)CC2415LHE EW(1/2)CC3015LHE EW(1/2)CC3615LHE corner counter cap - extended right Laminate EW(1/2)CC2415RHE EW(1/2)CC3015RHE EW(1/2)CC3615RHE Worksurfaces and Tables corner counter cap - extended both ends Laminate EW(1/2)CC2415EE EW(1/2)CC3015EE EW(1/2)CC3615EE Example: EW1CC3015, 117, 117, 117 EW1 Worksurface CC Curved corner 30 Width 15 Depth 117 Soft Grey laminate 117 Soft Grey edge 117 Soft Grey cantilever trim Specify surface, trim and cantilever trim color. EW1 counter caps work with all existing counter caps and are for use with Generation 1 or Generation 2 panels. Plastic cantilevers are supplied. EW2 counter caps are for use with Generation 3 panels only. Counter caps are designed for mounting on top of panels. Corner counter caps-(e) extended one end, mount on top of 24,30 or 36 panels at 90 to each other. They are non-handed and screw holes for the mounting brackets must be field-drilled. Steel mounting brackets are supplied. A counter cap extension (E) covers one post. A counter cap extension (EE) covers 2 posts. Wood Grain and Metal edge bands: When specifying a top with a wood grain edge band add $25 to the standard list price. When specifying a top with a metal edge band add $50 to the standard list price. 119

120 Veneer Worksurface straight and corner description dimensions w d pattern no. list price Rectangular EWV2424Ge $ EWV2430Ge EWV3024Ge EWV3030Ge EWV3624Ge EWV3630Ge EWV4224Ge EWV4230Ge EWV4824Ge EWV4830Ge EWV4836Ge EWV5424Ge EWV5430Ge EWV6024Ge EWV6030Ge EWV6036Ge EWV6624Ge EWV6630Ge EWV6636Ge EWV7224Ge EWV7230Ge EWV7236Ge EWV7824Ge EWV7830Ge EWV7836Ge 1, EWV8424Ge EWV8430Ge 1, EWV8436Ge 1,082. Corner With cut out EWVC4824KGe 1, EWVC3624Ge EWVC3630Ge EWVC4224Ge EWVC4230Ge EWVC4824Ge EWVC4830Ge 1,123. Example: EWV2430G, V09,117 EWV Worksurface 24 Width 30 Depth G Grommet V09 American Cherry veneer 117 Soft Grey trim Specify surface and trim color. Extended worksurfaces not available with support hardware included. Note: Veneer corner worksurfaces utilizes a diagonal grain direction. 120 Pattern numbers listed above are for worksurface only. See page 85 for Worksurface Loading and Support Application Information. For cantilevered worksurfaces, please add a C to the end of the pattern number and add $50 to the list price. Worksurfaces up to 48 inches wide will include one left hand and one right hand cantilever. Worksurfaces greater than 48 inches wide will include two left hand cantilevers and one right hand cantilever. The additional left hand cantilever is required for additional center support on tops spanning a distance greater than 48 inches. A center support must be used with a54 wide or larger worksurface.

121 Veneer Worksurface D, P and 9 description surface w d h dia. pattern no. list price Veneer D worksurface Veneer to 30 EWVD6030e $1, to 30 EWVD6036e 1, to 30 EWVD7230e 1, to 30 EWVD7236e 1, to 30 EWVD8436e 1,598. Veneer P/9 worksurface (9 shown) Veneer to EWV(P/9)7236e 1, to EWV(P/9)8436e 1, to EWV(P/9)9636e 1,766. Worksurfaces and Tables Example: EWVD7230C, V09, 117 EWV Worksurface D D top 72 Width 30 Depth C Supports included V09 American Cherry veneer 117 Soft Grey trim Specify surface and trim color. Specify hardware color for bases and stretcher rails. Note: P and D worksurfaces cannot be panel wrapped. Column bases and stretcher rails must be ordered separately. Note: For woodgrain direction see page 88. Designed for use as primary worksurfaces and for conferencing in small groups. To specify an EWV D, P or 9 top with support hardware (fixed-height column and stretcher rail) included add a C to the end of the pattern number and add $200 to the list price. 84 wide D, P and 9 worksurfaces include a V support bar mounted on the underside for additional stability. 121