MULTI-STAGES NFPA STYLE MOUNT

Transcription

1 ULTI-STGES NFP STYLE OUNT ore size from 1½" to 10" Stroke up to 12" High Flow Design 250 PSI IR, Two-Year Warranty N.F.P. Style ount HEY DUTY - HIGH FLOW 3 SERIES ULTI-STGES IR YLINDERS

2 3 ULTISTGE YLINDERS - Design features Solid luminum Head & ap achined from solid aluminum bar stock (6061 T6) and black anodized for corrosion resistance. (lso available in Stainless Steel ). Piston achined from solid aluminum bar stock (6061-T6). Offers long bearing support. Hard nodized ID luminum Tube (60 Rc) Provides superior wear resistance, and lower friction coefficient for maximum seal life. (lso available in Stainless Steel.) Piston Seal Lip-type low friction urethane piston seals are pressure energized and wear compensating for low friction an long life (temperature: -50 to 200 F) (iton also vailable up to 400 F) (all seals can be used in a non lube application) O-ring Tube End Seals Nitrile O-ring design is pressure compensated and reusable. Rod lips seal + wiper Our New Design with a real rod u-cup is completely self compensating for zero leakage at all pressures (all seals can be used in a non lube application) The New Wiper Wipes dirt out for less maintenance and longer life of the cylinder. (Urethane) (temperature: -50 to 200 F) Piston Wear Ring Nylon material is design for low friction, and to ensure maximum wear in the cylinder in side load application. Eliminates metal-to-metal contact. Rod Gland ronze gland is externally removable without cylinder disassembly for easy maintenance. Designed to provide maximum rod bearing. (lso available in cetal) Piston Rod High Strength steel. NITRORURIZING treatment on the rod gives better corrosion-resistant properties (out performs 12-micron (.0005 in.) chromium electroplating by ratio up to 20:1.), improved wear resistance, better lubrication retention, dent resistance without induction hardening (60Rc), environmentally Friendly, no surface pitting, flaking, or hydrogen embrittlement. The finish created by the process is a lustrous black.(vailable in stainless steel) Tie rods orrosion resistant (Nitro carburizing), stress proof steel maintains uniform compression on tube end seals. (vailable in Stainless steel) id Plate High Flow id plate with 2 orifice (vent/vaccum) ade of 6061-T6 luminum and lack anodized, design for resistance, and Flow in mind ( available with 2 or 3 port for external vent/vaccum or muffler). Upper Rod High Strength steel. NITRORURIZING treatment on the rod. High Flow design. umper Incorporated bumper in piston to ensure long life and noise free, design for long life, those bumper are incorporated into the piston with enough space to expand without damaging the seal E J L K D G I F H - 2 -

3 3 YLINDERS - Dimensions 2 STGES EE N.P. T. * DD TP KK FELE THRED DEPTH K J UU / EXHUST L2 + (2 x STROKE) G L E SQ Z2 + (2 x STROKE) 3 STGES EE N.P. T. * DD TP KK FELE THRED DEPTH K J UU / EXHUST L3 + (3 x STROKE) G L E SQ Z3 + (3 x STROKE) 4 STGES EE N.P. T. * DD TP KK FELE THRED DEPTH K J UU / EXHUST L4 + (4 x STROKE) G L E SQ Z4 + (4 X STROKE) ORE L E DD EE G J KK 1 1/2 3/4 1 1/8 1,43 3/8 2 1/4"-28 3/8 1 1/2 1 7/16"-20 5/8 5/8 2 3/4 1 1/8 1,84 3/8 2 1/2 5/16"-24 3/8 1 1/2 1 7/16"-20 5/8 5/8 2 1/2 3/4 1 1/8 2,19 3/8 3 5/16"-24 3/8 1 1/2 1 7/16"-20 5/8 5/8 3 1/4 1 1/8 1 1/2 2,78 1/2 3 3/4 3/8"-24 1/2 1 3/4 1 1/4 3/4" / /8 1 1/2 3,32 1/2 4 1/2 3/8"-24 1/2 1 3/4 1 1/4 3/4" / /8 1 1/2 4,12 1/2 5 1/2 1/2"-20 1/2 1 3/4 1 1/4 3/4" / /8 2 4,88 5/8 6 1/2 1/2"-20 3/ /2 1" / /8 2 6,44 5/8 8 1/2 5/8"-18 3/ /2 1" /8 1 2 STGES 3 STGES 4 STGES ORE L2 Z2 L3 Z3 L4 Z4 1 1/2 5 3/8 6 3/8 7 1/8 8 1/8 8 7/8 9 7/ /8 6 3/8 7 1/8 8 1/8 8 7/8 9 7/8 2 1/2 5 5/8 6 5/8 7 1/2 8 1/2 9 3/8 10 3/8 3 1/4 6 1/4 7 5/8 8 1/4 9 5/8 10 1/4 11 5/ /4 7 5/8 8 1/4 9 5/8 10 1/4 11 5/ /4 8 1/ /8 11 1/4 12 5/ /2 9 1/ /8 12 1/2 14 1/ /4 9 3/8 10 3/ /8-3 -

4 3 - Rod Thread Dimensions & multi stage force STNDRD Rod end style THD OPTIONL KK THD KK THD DEEP STYLE #1 LRGE LE THRED STYLE #2S (STUDDED) For 1.5 to 5 ore STYLE #4 FELE THRED D ROSS FLTS KK THD FF THD NOTE: STYLE #4 FURNISHED S STNDRD UNLESS OTHERWISE SPEIFIED. #1 #1F #2 & #4 ROD DI. D FF KK 5/8 3/4 3/8 1/2 5/8 1/2-20 5/8-18 7/ /8 1/2 7/8 7/8 7/ / /8 1 5/8 5/8 1 3/ / / /4 2 3/4 1 1/2 1 1/8 1 1/ / / /8 7/8 1 3/4 1 1/8 1 3/ /2-12 STYLE #2 SLL LE THRED (On 6 ore and over) STYLE #1F FULL DI LE THRED This grid is to show How much force you can get by using our 3 ultistage cylinder. ll the forces are calculated with a pressure of 100 ps.i. ultistage cylinders can be use in push (extend) or Pull (retract) or oth, Stock stroke is 1, 2, 3, 4, 6, but can be ordered up to 12 stroke FORE (in pounds at 100 psi) 2 STGES 3 STGES 4 STGES ORE Extend Retract Extend Retract Extend Retract 1 1/ / / ore Stage than 4 can be ordered ask your sales representative for a special quote. 10 bore also available on special request

5 3 YLINDERS - ounting Dimensions E5 - HED RETNGULR OUNT UF TF J UU / EXHUST G F (4) R E6 - P RETNGULR OUNT TF UF R F (4) J UU / EXHUST G F1 - HED FLNGE OUNT W UF TF UU / EXHUST F F (4) R ORE R TF UF F E F G J W 1 1/2 1,43 2 3/4 2 3/8 5/16 1 1/8 3/8 2 3/8 1 1/2 1 5/8 5/8 2 1,84 3 3/8 4 1/8 3/8 1 1/8 3/8 2 1/2 3/8 1 1/2 1 5/8 5/8 2 1/2 2,19 3 7/8 4 5/8 3/8 1 1/8 3/8 3 3/8 1 1/2 1 5/8 5/8 3 1/4 2, /16 5 1/2 7/16 1 1/2 1/2 3 3/4 5/8 1 3/4 1 1/4 7/8 7/8 4 3,32 5 7/16 6 1/4 7/16 1 1/2 1/2 4 1/2 5/8 1 3/4 1 1/4 7/8 7/8 5 4,12 6 5/8 7 5/8 7/16 1 1/2 1/2 5 1/2 5/8 1 3/4 1 1/4 7/8 7/8 6 4,88 7 5/8 8 5/8 9/16 2 5/8 6 1/2 3/ /

6 3 YLINDERS - ounting Dimensions S4 - SIDE TPPED OUNT SN2 + (STROKE x 2 STGES) SN3 + (STROKE x 3 STGES) SN4 + (STROKE x 4 STGES) XT NT TP TK DEEP (4) 3 TN E3 - SQURE HED OUNT UU / EXHUST W F (4) R 3 E4 - SQURE P OUNT R 3 F (4) UU / EXHUST ORE SN1 SN2 SN3 NT TK TN F R W 1 1/ /4 7 1/2 1/4-20 3/8 5/ /4 7 1/2 5/ /2 7/8 2 1/2 4 1/4 6 1/8 8 3/8-16 5/8 1 1/4 3 1/4 4 5/8 6 5/8 8 5/8 1/2-13 3/4 1 1/ /8 6 5/8 8 5/8 1/2-13 3/4 2 1/ /8 7 3/8 9 5/8 5/ / /8 8 1/8 10 5/8 3/ /8 3 1/ /8 8 1/2 11 1/8 3/ /8 4 1/2 11/ /8-6 -

7 3 YLINDERS - ounting Dimensions P1 - SHORT LEIS OUNT D dia W W L L learance Radius P1 X2 + (STROKE x 2 STGES) X3 + (STROKE x 3 STGES) X4 + (STROKE x 4 STGES) P2 - LONG LEIS OUNT D dia W W L FL XD2 + (STROKE x 2 STGES) XD3 + (STROKE x 3 STGES) XD4 + (STROKE x 4 STGES) P4 - EYE PIOT OUNT D dia L FL XD2 + (STROKE x 2 STGES) XD3 + (STROKE x 3 STGES) XD4 + (STROKE x 4 STGES) ORE D W FL L 1 1/2 3/4 1/2 1/2 1 1/8 3/4 5/8 2 3/4 1/2 1/2 1 1/8 3/4 5/8 2 1/2 3/4 1/2 1/2 1 1/8 3/4 5/8 3 1/4 1 1/4 3/4 5/8 1 7/8 1 1/4 7/ /4 3/4 5/8 1 7/8 1 1/4 7/ /4 3/4 5/8 1 7/8 1 1/4 7/ /2 1 3/4 2 1/4 1 1/2 1 1/ /4 2 1/4 1 1/2 1 2 STGES 3 STGES 4 STGES ORE X2 XD2 X3 XD3 X4 XD4 1 1/2 7 1/8 7 1/2 8 7/8 9 1/4 10 5/ /8 7 1/2 8 7/8 9 1/4 10 5/ /2 7 3/8 7 3/4 9 1/4 9 5/8 11 1/8 11 1/2 3 1/4 8 7/8 9 1/2 10 7/8 11 1/2 12 7/8 13 1/ /8 9 1/2 10 7/8 11 1/2 12 7/8 13 1/ / /8 12 1/4 13 7/8 14 1/ /8 11 3/8 13 1/8 13 7/8 15 5/8 16 3/ /8 13 1/2 16 1/8-7 -

8 3 YLINDERS - Hall Effect & Reed Switches Reed switches are constructed of two overlapping ferromagnetic reeds which are sealed in a glass tube with the ends aligned and a small gap between them. When an external magnetic force is applied, the reed assumes opposite polarity, the ends of the reeds attract each other and make contact, completing the circuit. Reed switches are not recommended in sensitive areas since they can introduce electrical noise into the circuit due to bounce and vibration from mechanical closing of the reeds. Hall Effect switches are solid state switches with no moving parts. The solid state switches is activated when the silicon chip (Hall) senses a magnetic field. Since there are no moving parts, Hall effect switches can operate in sensitive areas without sending interference or noise into the circuit. How To Order Switch specifications Switch part Number Spec. Reed Switch, Electronic Sensor, Electronic Sensor, O, LED LED, Sourcing LED, Sinking able length Switching oltage D/ 50/60 Hz Switching urrent Switching power Switching Speed 0.5 mp ax mp in. 10 Watts ax. 0.5 ms operate 0.1 ms release 9ft P able 6-24 D 6-24 D 0.5 mp ax. 0.5 mp ax. 12 watts ax. 12 watts ax. 1.5µs operate 0.5µs release 1.5µs operate 0.5µs release oltage Drop 3.5 olts 1.0 olts 1.0 olts Temperature range -20 to 80-4 to 176 F Switch Function SPST Normally Open Normally open PNP output Normally open NPN output Shock up to 30G (11msec.) ibration up to 20G (10-55 Hz) x00 - x xx LSO ILLE 8 QUIK ONNET Wiring Diagrams + SUPPLY 6-24 D - REED SWITH 04 WHT - ~ SUPPLY /D + ~ RN WHT LOD *LOD sourcing *LOD sinking GRN RN ELETRONI SWITH 31 LED, SOURING ELETRONI SWITH 32 LED, SINKING - WHT SUPPLY 6-24 D + RN LOD GRN Series racket code Suffix 2 = 1-1/8, 1½, 2 & 2½ bore = 3¼ & 4 bore = 5, 6 & 8 bore onnections 0-9ft P wire 3-8 mm Quick onnect Type ode 04 - Reed switches 31 - Hall Effect PNP 32 - Hall Effect NPN Switch dimensions " For 1-1/8 to 2½ bore For 2 to 4 bore For 5 to 8 bore - 8 -

9 3 YLINDERS - ounting options & NFP accessories NFP levis racket FL DD tap W W L D E sq. RE PRT # D W DD E FL L RE USED ON ORES /2 1/2 3/ ½ 1 1/8 3/4 1/2 1 5/8 1½ - 2-2½" /4 5/8 1/ ½ 1 7/8 1 ¼ 3/ /4 5/ ½ 2 ¼ 1 ½ /8 1 5/ /8 1 3/ ¾ 1 ¼ 7/ ½ 3 1/8 2 ¼ 1 ¾ 2 9/16 3¼ - 4-5" 3 ¼ 6-8" 3 13/ " 4 15/16 10" FL DD NFP Eye racket L E sq. RE D PRT # E-05 E-07 E-10 E-13 D DD E FL L RE USED ON ORES.75 1/2 13/32 2 ½ 1 1/8 3/4 1/2 1 5/8 1½ - 2-2½" /4 17/32 3 ½ 1 7/ /32 4 ½ 2 ¼ /8 21/ ¼ 1 ½ 3/ /8 1-3/8 2 9/16 3 ¼ 3 13/16 3¼ - 4-5" 6-8" 8-10" E ¾ 29/32 6 ½ 3 1/8 2 ¼ 1-3/4 4 15/16 10" NFP rod clevis W W ER D PRT # D E H W ER KK L R /2 1 ½ 1 1/2 1/2 7/ /4 R /4 2 3/8 1 ¼ 5/8 3/4 3/ ¼ E KK H ROSS HEX FLTS R-10 R /8 1 ½ 3/ ½ /8 4 1/ /8 1 1/ /8 OTHER SIZE RE ILLE, SK YOUR DISTRIUTOR OR FTORY. (R-17 KK=1½-12, R-20 KK=1-7/8-12, R-25 KK=2¼-12, ET) NFP rod eye D ER PRT # D ER KK D RE-05 3/4 1 ½ 3/4 1/2 5/8 7/16-20 KK D dia. RE-07 RE-10 RE /8 2 1/16 1 ¼ 3/4 1 5/8 2 13/16 1 ½ / /8 7/8 1 3/16 1 9/16 OTHER SIZE RE ILLE, SK YOUR DISTRIUTOR OR FTORY. (RE-17 KK=1½-12, RE-20 KK=1-7/8-12, RE-25 KK=2¼-12, ET) 3/ /4-12 PIN PRT # D D Snap ring included P-05 P P P P P

10 3 YLINDERS - Dimensions EXPLE 3S2-4x10-ES4R1- is a 3 series, 4" bore, 10" stroke, 4 stages in extend Stroke, 1 in retract side lug mount, female rod thread, with umpers ODEL 3 SI ODEL 3O OERSIZE ROD 3 S2-4 x 10 - SE4R1 - #4 - ROD END OPTIONS OUNTING OPTIONS E3 E4 E5 E6 F1 P1 P2 P4 S1 S4 T1 T2 T4 X1 X2 X3 SQURE HED OUNT SQURE P OUNT RET. HED OUNT RET. P OUNT HED RET. FLNGE DETH. SHORT LEIS OUNT DETH. LEIS OUNT DETH. EYE OUNT NGLE OUNT OTTO TP OUNT HED TRUNNION OUNT P TRUNNION OUNT INTEREDITE TRUNNION OUNT OTH TIE RODS EXTENDED P END TIE RODS EXTENDED HED END TIE RODS EXTENDED ORE 1 1/ /2 3 1/ " STROKE STD ask for other strokes ULTI STGES #1 LE, large #1F LE, full dia. #2 LE, small, #2s LE, studded #4 FELE, STD #X SPEIL S Ex Rx Ex : Nb of stage for the Extend stroke (E4, 4 stages extend) Rx : Nb of stage for the retract stroke (R1, 1 stages Retract) Pxx PORT POSITION (1,2,3,4) USHION POS. (1,2,3,4) REx NR H ROD EXTENSION SELS DE OF iton NON-ROTTING (for pick & place appl.) GNETI PISTON UPER OTH ENDS UPER P END UPER HED END To order seal kits add the prefix 3SK to the bore and rod diameter ex: 3SK and for bronze gland kit add the prefix 3GK to the rod diameter ex: 3SK-1375 LINER LIGNENT OUPLERS - hoose from 19 sizes Starcyl s linear alignment couplers extend the bearing and seal life of your cylinders. Our couplers prevent binding and Erratic movement that misalignment causes, which eventually wears down your cylinders. Not only do Starcyl couplers work equally well in push and pull applications, but they allow a greater tolerance between the cylinder centerline and the mating member. 1/16 RDIL FLOT 2 SPHERIL OTION THD F SHNK DI. G ROSS FLT E D E THD Use jam nut to lock coupler to rod when used with full diameter threads. iton are registered trademarks of DuPont Dow Elastomers. H ROSS FLT PRT # D E F G H X PULL T YIELD -250F 1/4-28 7/8 1 1/4 1/4 5/ /16 13/ F 5/ /8 1 1/4 1/4 5/ /4 13/ /8-16 7/8 1 1/4 1/4 5/ /16 13/ F 3/8-24 7/8 1 1/4 1/4 5/ /16 13/ F 7/ /4 2 1/2 3/4 5/8 9/16 1 1/ / /4 2 1/2 3/4 5/8 9/16 1 1/ F 1/ /4 2 1/2 3/4 5/8 9/16 1 1/ F 5/ /4 2 1/2 3/4 5/8 1/2 1 1/ / /4 2 5/16 5/16 1 1/8 31/32 7/8 1 1/ F 3/ /4 2 5/16 5/16 1 1/8 31/32 7/8 1 1/ F 7/ /4 2 5/16 5/16 1 1/8 31/32 7/8 1 1/ F /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ F 1-1/ /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ F 1-3/ /2 2 15/16 1/2 1 5/8 1 3/8 1 1/4 2 1/ F 1-1/ /4 4 3/8 13/16 2 1/4 1 3/4 1 1/ F 1-3/ /4 4 3/8 13/16 2 1/4 1 3/4 1 1/ F 1-7/ /4 5 7/16 11/ /4 1 7/8 3 1/ F /4 5 7/16 11/ /4 1 7/8 3 1/ Part numbers -250F through -1250F in UNF are stock items **4:1 safety factor included **

11 3 YLINDERS - NOTES

12 OTHER PRODUTS: STR3 SERIES - N.F.P.. INTERHNGELE YLINDERS ORE SIZES 1½ - 10 Not Enough Force Don't hange The Design dd Stage! THE ONLY YLINDER UPGRDLE! STR 1 SERIES STR1 - UPGRDLE SPE SER YLINDERS ROUND LINE SPESER YLINDERS FIND US ON THE INTERNET EIL : STRYL@STRYL.O YOUR STRYL DISTRIUTOR: STRYL YLINDER IN. IN US : STRYL ( ) fax: IN N : fax (450) PRINTED IN ND TLOG # 3-DE03