Seattle (564) Bungalow & Tree of Life Face
|
|
- Briana Mills
- 5 years ago
- Views:
Transcription
1 Compatibility: 564 SS Gas Fireplace 564 Electric Fireplace Packing List: Used on Both Fireplaces Doors Used on 564 SS Gas Fireplaces Only Used on 564 E Electric Fireplaces Only Hinge Pins Hinge Brackets 8-32 Nuts Heat Shield Wood Screws Hinge Pin Shims Avalon Emblem Magnets Included with Tree of Life #10 Handles 8-32 x 1/2 Screws Washers Included with Bungalow Handles Optional Door Screens 8-32 x 1/2 Screws Upper and Lower Grills Glass Frame Cover #8 x 3/8 Sheet Metal Screws Hinge Brackets Anchor Anchor Bracket Cove Cover The center deflectors must be in place when using this face to prevent the facing above the fireplace from becoming too hot. If this face is replacing a Grill ( ), make sure to replace the center deflectors. Page 1 of 12 6/2/09 Travis Industries, Inc.
2 Installation Details 564 SS 27-1/2 SIDE OF FIREPLACE 32-3/8 NOTE: If using facing over 1/2 thick, the doors will not fully open. 1 3/4 Page 2 of 12 6/2/09 Travis Industries, Inc.
3 Optional Door Screen Inserts Bungalow Only OPTION A - Basket Weave (installed in the doors). Place the doors in an upright position. Attach the handle (2) to the door with the included screws (3). Slide the hinge pins (4) into place. OPTION B Mesh Door Screen (shipped separately with this kit). Place the doors (1) face down on a suitable work surface). Remove the nuts (7) holding the upper (5) and lower (6) inserts in place. Remove the inserts and install the mesh screens. Note: the screens have a sheet-metal frame spot-welded to them - make sure the sheet-metal faces outward this protects the screen and covers the sharp edges. Secure the screens with the nuts removed earlier. Do not over-tighten Place the doors in an upright position. Attach the handle (2) to the door with the included screws (3). Slide the hinge pins (4) into place Page 3 of 12 6/2/09 Travis Industries, Inc.
4 Installation 564 SS 1 Remove the glass frame from the fireplace (see the owner's manual for details). 2 Install the hinge brackets onto the fireplace following the directions below. Remove and discard the nuts and bushings attached to the stud plates near the firebox (HINT: To prevent the stud plates from falling out, we recommend removing one nut and bushing and installing a nut before removing the second nut and bushing.). Discard the nuts and bushings. Attach the nuts included with this kit. Do not secure the nuts all the way - leave a 1/8 gap between the nut and the stud plate. 1/8 Slide the hinge brackets into place - the slots on the bracket slide over the press studs on the fireplace. Use a wrench to securely tighten the lower nut to prevent the hinge bracket from bending while the doors are in place. 11/32" Open End Wrench Secure the hinge brackets to the fireplace with the included screws. Repeat these steps for the opposite side. Hand-tighten these nuts on the stud plates. NOTE: The hinge brackets have a notch on the lower inside edge - this helps determine the left bracket from the right bracket. Page 4 of 12 6/2/09 Travis Industries, Inc.
5 3 Install the glass frame cover following the directions below. Place the cover over the top of the door frame. Push these tabs inwards to lock the cover in place. 4 Attach the glass frame to the fireplace. Page 5 of 12 6/2/09 Travis Industries, Inc.
6 5 Install the upper and lower grills (mesh screens) following the directions below. NOTE: The upper and lower grills are different. The lower grill has end-stops on either side. Upper Grill Installation Hold the grill at an angle and insert the lower slot over the bushing on the hinge bracket (both sides). You may need press on the grill to get the tab over the bushing (this prevents the grill from accidentally falling off). Swing the grill upwards to engage the upper slot. You will need to lift the grill slightly to get it over the bushing. Once in place the grill is held in place by gravity. Lower Grill Installation Place the Avalon label onto this plate before shutting the grill. Hold the grill at an angle and insert the lower slot over the bushing on the hinge bracket (both sides). You may need to press on the grill to get the tab over the bushing (this prevents the grill from accidentally falling off). Bend the end-stop tab over on both sides. This allows the grill to swing forward without disengaging. Swing the grill upwards to engage the upper slot. You will need to lift the grill slightly to get it over the bushing. Once in place the grill is held in place by gravity. Page 6 of 12 6/2/09 Travis Industries, Inc.
7 6 Hold the doors at a 90 angle to the fireplace and install onto the hinge brackets (see the illustration below). Swing the doors closed - NOTE: the left door closes behind the right door. Hold each door at a 90 angle to the backing plate and hang in place. USING THE HINGE SHIMS (washers): Eight shims are included with the doors to provide proper door alignment. If the doors drag on the hearth, place one or two shims between the door and face hinge. ADJUSTING THE HINGES: The hinges may be adjusted by bending the tabs to the left or right. This allows the doors to be aligned left or right, top to bottom. NOTE: place a rag over the hinge posts before grasping the hinge posts with pliers to prevent scratching. NOTE FOR INSTALLATIONS WITH THICK FACINGS (e.g.: BRICK, ROCK): The hinge pins can be slid into place after the doors are aligned over the hinge brackets. This eliminates the need to "drop" the doors into place. Page 7 of 12 6/2/09 Travis Industries, Inc.
8 7 Magnets are shipped attached to one of the doors. Position the magnets on the back side of both doors as shown below. The magnets have felt attached to one side make sure the felt side contacts the fireplace (this keeps the magnets adhered to the door, not the fireplace). Attach the handles as shown below. NOTE: The magnets are shipped attached to the doors. These powerful magnets may require pliers to properly position. Take care with the magnets to prevent damage and keep them away from children. Attach the door handles as shown to the left. The tree of life handles require a washer and screw, the bungalow requires two screws. Place the magnets in these locations (with the felt facing up). These magnets attach to the doors and help keep the doors shut when in use. Page 8 of 12 6/2/09 Travis Industries, Inc.
9 Installation 564 Electric 1 Install the upper heat shield onto the 564 E fireplace. Remove and discard the stock upper heat shield. Place the upper heat shield included with this kit on top of the fireplace (note position) and secure with the same screws. 2 Install the hinge brackets following the directions below. a Remove the right side bracket from the fireplace (right side only - these brackets hold the glass in place). b Use the screws removed in step a to secure the hinge brackets to the fireplace. c Repeat steps a and b for the left side bracket. NOTE: This tab must be on the bottom side of the bracket (this distinguishes the left from the right side). NOTE: There are two tabs on each side of the fireplace that need to be bent to accept the new brackets. Use a screwdriver to bend them out. Page 9 of 12 6/2/09 Travis Industries, Inc.
10 3 Pull the fireplace out of the mantel (or enclosure) and attach the anchor and anchor bracket following the directions below. a Remove the two screws on the back of the fireplace. Attach the anchor bracket to the back of the fireplace with the longer side of the bracket on top. b IF USING THE 564 E MANTEL Center the back edge of the anchor with the back edge of the hearth. Secure with the included wood screws. IF USING A BUILT IN INSTALLATION Mark a line 12 back from the enclosure opening (include the drywall, tile or other wall covering). Center the back edge of the anchor along this line and secure with the included wood screws. Slide the fireplace into place to verify the anchor and anchor bracket c work correctly. The anchor bracket should engage the anchor, preventing the fireplace from tilting forward when in place. Page 10 of 12 6/2/09 Travis Industries, Inc.
11 4 Pull the electric fireplace out of the mantel (or built-in location). Attach the cove cover and doors following the directions below. Slide the fireplace back into place, making sure the anchor engages the bracket, preventing the fireplace from tilting forward when the doors are opened. a Hang the 564 E cove cover over the glass - this keeps light from exiting the grill opening along the top of the face. c Place the Avalon label on this cover. b Hold each door at a 90 angle to the backing plate and hang in place. USING THE HINGE SHIMS (washers): Eight shims are included with the doors to provide proper door alignment. If the doors drag on the hearth, place one or two shims between the door and face hinge. ADJUSTING THE HINGES: The hinges may be adjusted by bending the tabs to the left or right. This allows the doors to be aligned left or right, top to bottom. NOTE: place a rag over the hinge posts before grasping the hinge posts with pliers to prevent scratching. 5 Magnets are shipped attached to one of the doors. Position the magnets on the back side of both doors as shown below. The magnets have felt attached to one side make sure the felt side contacts the fireplace (this keeps the magnets adhered to the door, not the fireplace). Attach the handles as shown below. Page 11 of 12 6/2/09 Travis Industries, Inc.
12 NOTE: The magnets are shipped attached to the doors. These powerful magnets may require pliers to properly position. Take care with the magnets to prevent damage and keep them away from children. Attach the door handles as shown to the left. The tree of life handles require a washer and screw, the bungalow requires two screws. Place the magnets in these locations (with the felt facing up). These magnets attach to the doors and help keep the doors shut when in use. Page 12 of 12 6/2/09 Travis Industries, Inc.
Used on 564 SS Gas Fireplaces Only. #8 x 3/8 Sheet Metal Screws. Upper and. Lower Grills. Heat Shield
Compatibility: 564 SS GS 564 DF GS 564 HO GS 564 Electric Fireplace Packing List: Used on Both Fireplaces Doors Used on 564 SS Gas Fireplaces Only Mounting Brackets #8 x 3/8 Sheet Metal Screws Used on
More information564 Shadowbox Face (w Screen) Instructions
Packing List Compatibility Face Bottom Shield (2) Face Brackets (8) Screws (#8 x 3/8 Phillips) (5) Screws (#8 x 5/8 hex head) Drill Template 11/64 Drill Bit Items Used with Optional Switch Box (see note
More informationDVL / 33 DVI Shadowbox Face Installation Instructions (SKUs Black: ; Bronze: )
Packing List Shadowbox Face Hinge Bracket Stud Plate (2) 10-24 Nuts, (3) 8-32 Nuts NOTE: Older versions used (5) 10-24 Nuts (1) 10-24 Type F Screw Switch Bracket LED Switch Bracket LED Mounting Plate Compatibility
More informationDVS / 31 DVI Shadowbox Face Installation Instructions (sku black: bronze: )
Packing List Shadowbox Face (3) 8-32 Nuts (10) 10-24 Type F Screws Face Bracket Hinge Bracket Latch Bracket Switch Bracket (used on 31 DVI only) LED Switch Bracket LED Mounting Plate Compatibility DVS
More informationMake sure all wiring is inserted into the cavity between the insert and the fireplace. Failure to do this may cause the wiring to become damaged.
Installation Notes Large Flush Wood Hybrid-Fyre Insert: (96400539, 96400539A) Before installing, make sure to install the one-piece panel, and disconnect the power cords making sure the Molex connector
More informationDVS Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Attach the Surround Panels (if applicable)... 6 Assemble the Face... 7 Attach the
More informationJ&M Mustang Rear Adjustable Lower Control Arms Installation Guide (99-04)
J&M Mustang Rear Adjustable Lower Control Arms Installation Guide (99-04) 1. Required Tools: 1.1. 3/8 ratchet 1.2. 1/2 ratchet 1.3. 18mm deep socket 1.4. 18mm standard socket (optional) 1.5. 19mm open
More information1080 CF Valve Replacement Instructions
Overview This kit includes the newer American Flame gas control valve designed specifically for the 1080 CF gas fireplace. If you have a 1080 CF fireplace, and you are uncertain as to whether this kit
More informationRollstar Shade Installation Instructions
Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the
More information(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers
PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers
More informationDVL Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Assemble the Face... 6 Attach the Surround Panels (if applicable) and Face... 10 Hang
More information2004 Ford Expedition
DISC BRAKE PADS Removal (Front) WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationFan, DVI Insert 31 and 33 DVI Installation Instructions (sku )
Packing List Fan, DVI Insert 31 and 33 DVI Left and Right Blower Assembly (with grommets and bushings) (2) Blower Mounting Nuts Wiring Harness Rheostat Snap Disc Rheostat Nut and Knob Nylon Rheostat Spacer
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2
INSTALLATION INSTRUCTIONS 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2 PARTS LIST: 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting
More informationX.L. BAND W/ SPRING ASSIST INSTRUCTION MANUAL
PARTS LIST X.L. BAND W/ SPRING ASSIST INSTRUCTION MANUAL (2) Bands (1) Handle assembly (2) Side hinge assemblies (1) Left rear hinge assembly (1) Right rear hinge assembly (2) front spring s (2) rear spring
More information20964/B 20964/B 2014 TOYOTA TUNDRA TUNDRA. Billet Grille. Fig 1. Fig 2
Billet Grille TOOLS REQUIRED: PARTS LIST: Socket Set (6) U-Nuts Flat/Phillips Screw Drivers (8) #10 Screws Pliers (2) #8 Screws ¾ (2) 2 Flange Bracket (1) Top Plate Overlay Bracket - driver (1) Top Plate
More informationUSER'S MANUAL and INSTALLATION GUIDE
AM Inlet Series 8" and 2" baffle AM0896GS AM296GS USER'S MANUAL and INSTALLATION GUIDE TABLE OF CONTENTS Section Page...Requirements for Installation...2 2...Unpacking the AirManager... 3-5...Exploded
More informationFRONT SEAT TRACK MOTOR. Removal
1 of 19 FRONT SEAT TRACK MOTOR Removal WARNING: - Always wear safety glasses when repairing a supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk
More informationCetra Assembly Instructions
99877 Revision F- Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 0 Kimball International, Inc. T 800.8.88 F 8.8.800
More informationZ-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly
Checking and Replacing the AC Motor To remove and replace the AC Motor you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Removing the AC Motor 1. Ready the machine by
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA / SEQUOIA PART # &
(W) INSTALLATION INSTRUCTIONS PART # 501894 & 501895 PARTS LIST: 1 Grille Guard 4 3/8" Flat Washers 1 Driver/Left Frame 2 3/8" Nylon Lock Nuts 1 Passenger/Right Frame 4 12mm Plastic Washers 1 Driver/Left
More informationMaintenance Information
Form 04584058 Edition 1 November 2004 Air Impactool 2141P and 2141PSP Maintenance Information Save These Instructions Disassembly General Instructions 1. Do not disassemble the tool any further than necessary
More informationFabric Studio Custom Roll Shades Installation Instructions
Fabric Studio Custom Roll Shades Installation Instructions Cassette System Battery Motor Lifting System Inside or Outside Mount Thank you for purchasing your new roll shade. It has been custom-made from
More informationSHOP PRO FXP 95 UPGRADE KIT (REGULATED)
1. Make sure the Shop Pro FXP is disconnected from the 120VAC power source. 4. Loosen the five ¼" headed bolts slightly until the motor cover slides to the left and remove the cover. 2. Remove the vent
More informationCoupler Mounted Bracket
Coupler Mounted Bracket INSTRUCTION MANUAL & GUIDELINES CMBA & CMBA M Issued October 2015 Please discard previous CMBA installation instructions CMB INSTRUCTIONS & GUIDELINES TABLE OF CONTENTS CMB Installation
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067
INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left
More informationDVM36/42 SERIES LOG SET/BURNER MODULES INSTALLATION INSTRUCTIONS
DVM36/42 SERIES LOG SET/BURNER MODULES INSTALLATION INSTRUCTIONS For Use With (V)TC36 Series, (V)VC36/42 Series, (V)KC36/42 Series or DVC Series Fireplaces This log set/burner module must be installed
More informationGMC Yukon
Torch Series LED Grille TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationAssembly & Installation Instructions
TM P R O D U C T S Assembly & Installation Instructions FOR 28 SERIES SNOWPLOW PIVOT ASSEMBLY AND FLOAT LIMITER 99103000 FOR SERIAL NUMBERS 28D100000 TO 28D100770 97100552A 1. THINK SAFETY, ALWAYS WEAR
More informationINSTALLATION GUIDE CRF150R Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659
More informationInstallation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119
Installation Guide 2008 - Current Ford F-250 & Ford F-350 Super Duty Product Code: 109 & 119 September 1, 2012 Tools Needed Components Included 3/8" Drill P2 Tip #2 Philips Screwdriver 1/2" Drill Bit Hinged
More informationFIFTH WHEELS TROUBLESHOOTING AND REBUILD PROCEDURES. XA-71 Series Fifth Wheel Top Plates. XA-71-DA 2 SAE Kingpin (Rebuild Kit RK-65014)
GO THE DISTANCE. FIFTH WHEELS TROUBLESHOOTING AND REBUILD PROCEDURES XA-71 Series Fifth Wheel Top Plates XA-71-DA 2 SAE Kingpin (Rebuild Kit RK-65014) XA-71-DA-03705 2 SAE Kingpin for FW2570-7103 SERIES
More informationDODGE RAM 2500/3500 (4WD) *HEMI ENGINE ONLY* (INCLUDING MEGA CAB) (EXCLUDING POWER WAGON) 3 BODY LIFT INSTALLATION INSTRUCTIONS KIT# 60223
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net DODGE RAM 2500/3500 (4WD) *HEMI ENGINE ONLY* (INCLUDING MEGA CAB) (EXCLUDING POWER WAGON) 3 BODY LIFT INSTALLATION INSTRUCTIONS 2010-2012
More informationService Manual Mozart Fireplace
Service Manual Mozart Fireplace Model Numbers: CFP3913 REV PCN DATE 00 11637 Sep 23, 09 Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 1-888-346-7539 www.dimplex.com In
More information2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill
More informationRekluse Motor Sports. The z-start Clutch CRF 250R. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS112 CRF 250R
Rekluse Motor Sports The z-start Clutch CRF 250R Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS112 CRF 250R 191-212 Manual Revision: 091205 Rekluse Motor Sports, Inc.
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC2001, RC2001X Applications: Mopar 8-3/4 & 9-3/4 Rear Axles Thank you for choosing Leed Brakes for your automotive product needs. Before
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2004 S2000 AII 26323-31611 Issue Date DEC 2005 PARTS LIST Rear defroster switch Hardtop 3-Pin subharness (If equipped, not used) 4-Pin subharness
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you
More informationRekluse Motor Sports. The z-start Clutch CRF 250X. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS116 CRF 250X
Rekluse Motor Sports The z-start Clutch CRF 250X Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS116 CRF 250X 191-216 Manual Revision: 103105 Rekluse Motor Sports, inc.
More informationELECTRICAL CONNECTORS B.1
ELECTRICAL CONNECTORS B. GENERAL The following table provides a brief description of the connectors found on your motorcycle. Connector numbers are listed in [brackets] in this manual. Table B-. Electrical
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive
More information1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
More information401B/1KDB CoolRite/FreezeRite Installation Manual I003
401B/1KDB CoolRite/FreezeRite Installation Manual 99-16105-I003 Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in
More informationPart Numbers: TTU-BGP14 & TTU-BGB14
Date: 10.14.2015 TOYOTA TUNDRA 2014-17 Billet Grille Part Numbers: TTU-BGP14 & TTU-BGB14 Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 2 Flange Brackets
More informationShort Shifter Installation Instructions Miata 6-Speed manual
Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter
More informationCERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT
PAGE 1 OF 9 CERTAIN 2013-2016 MODEL YEAR FUSION AND 2013-2014 ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT OVERVIEW In some of the affected vehicles, the bushing
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) & (3120/3320/3520/3720) HARD SIDED CAB ENCLOSURE (p/n 1JD3520AS) SOFT SIDED CAB ENCLOSURE
More information2003 Cadillac DeVille DTS
TRIM PANEL REPLACEMENT - SIDE FRONT DOOR Tools Required J 36796 Clip Zip Clip Removal Tool, or J 38778 Door Trim Pad Clip Remover Removal Procedure 1. Position the window fully downward. 2. Ensure the
More informationOne- Touch Installation Instructions
One- Touch Installation Instructions 1 1 Height Adjustable Pivot w/ screws 9 Upper Work Surface 2 Rail Mount Knobs 10 Back Cover 3 Transformer 11 Center Pivot w/ screws 4 Support Legs 12 Left Monitor Arm
More informationTECHNICAL BULLETIN. TP Issued Servicing Rockwell s TB Series Trailer Axles with Unitized Hub Assemblies
TECHNICAL BULLETIN TP-96175 Issued 12-96 Servicing Rockwell s TB Series Trailer Axles with Unitized Hub Assemblies TB Series Trailer Axles Introduction Rockwell s TB series trailer axle features a permanently
More informationTop Down Rollstar Shade Installation Instructions
Top Down Rollstar Shade Installation Instructions Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the dimensions you specified. With proper
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473.3664 F:620.869.9031 Turnoverball Gooseneck Hitch Installation Instructions
More informationINSTALLATION & OWNER S MANUAL
Rev. G, p. 1 of 19 INSTALLATION & OWNER S MANUAL YANMAR Sc SERIES cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC1AS Yanmar p/n: 59A40056727 Optional Hard Rear Panel Curtis p/n: SC100-06A
More informationRekluse Motor Sports, Inc. The z-start Clutch. Husaberg ( )
Rekluse Motor Sports, Inc. The z-start Clutch Husaberg (1989-2003) Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS125 Husaberg 89-03 191-225 Manual Revision: 012805
More informationTransmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
More informationAmtryke Model AM-12 & AM-16
Amtryke Model AM-12 & AM-16 Carton Contents Carefully remove and lay out all parts from the carton so as not to scratch or lose any parts or pieces. The shipping carton should contain the pictured items
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More information354 CHAPTER EIGHT WATER PUMP
354 CHAPTER EIGHT 33 Shift handle F : Forward N : Neutral R : Reverse proper alignment of the water tube to the water pump opening during each installation attempt. Make sure the locating pins enter the
More informationMaintenance Information
16584062 Edition 3 December 2013 High Torque Reversible Angle Screwdrivers and Angle Wrenches QA1L High Torque Series Maintenance Information Save These Instructions Product Safety Information WARNING
More informationEngine Removal / Installation Sea-Doo 951DI
Step 1 Battery Removal Step 2 Intake Removal 2.1 (Below) Loosen the two 10mm bolts and slide the intakes out of the brace on the exhaust manifold. Slide the intakes up and out of the hull. 2.3 (Below)
More informationBanks Monster Exhaust System
Banks Monster Exhaust System 2007-2008 Chevy/GMC 1500 Silverado 4.8L, 5.3L, 6.0L V-8 Gas, New Body Style THIS MANUAL IS FOR USE WITH MONSTER EXHAUST SYSTEMS 48344, 48345 Gale Banks Engineering 546 Duggan
More informationHeavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems
Heavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems Instruction Sheet 408-8039 02 JUN 16 Rev G Ram Post Wire Disc Insulation Disc Insulation Crimper Stripper
More informationRemove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
More informationSIT Pilot Assembly Retrofit - # 308 (Replaces R. Shaw Pilot Asbly) (SKU # )
Check Condition of Shipment SIT Assembly Retrofit - # 308 Upon receipt of this kit, check the condition of the packaging. Damage to the package should be noted on the carrier's freight receipt. Any damage
More informationMain Cover and Paper Input Assembly removal
Main Cover and Paper Input Assembly Remove the toner cartridge. Remove memory door (HP LaserJet 5L and 6L). CAUTION Remove the memory door first (HP LaserJet 5L and 6L). The door will break if you remove
More informationInstallation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A
Installation Manual AutoSteer Gleaner Combine AutoGuide 2 Steer Ready Supported Models A66 A76 R66 R76 S67 S77 PN: 602-0312-01-A LEGAL DISCLAIMER Note: Read and follow ALL Instructions in this manual carefully
More informationD-Drive Controller Retrofit Instructions
D-Drive Controller Retrofit Instructions These instructions will outline the procedure for replacing the circuitry within a Movotec D-Drive lift system. The circuit board is located within the black, metallic
More information235/245400, , 28N
Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters
More informationMaintenance Information
Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationInstallation Instructions for. For Use When Converting Model (V)M42(B) Vented Decorative Fireplace. Fold Bi-Fold Door After Releasing
Installation Instructions for PCBM-42 conversion kit Converting from Natural Gas to Propane/LP Gas For Use When Converting Model (V)M42(B) Vented Decorative Fireplace This conversion kit must be installed
More informationWOOD FIRE FLUE KIT AND ACCESSORIES MANUAL
WOOD FIRE FLUE KIT AND ACCESSORIES MANUAL Masport Limited 1-37 Mt Wellington Highway Panmure Auckland 6 Ph: 09 571 1200 Fax: 09 571 5864 www.masport.com 2005 CONTENTS Ordering Information... Page 3 Freestanding
More informationELECRAFT KX3 Application Note
ELECRAFT KX3 Application Note Installing the Speaker Grille Cloth Revision A, July 30, 2012 Copyright 2012, Elecraft, Inc., All Rights Reserved Background Some KX3 owners have reported issues with the
More informationJEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
More informationTO BE USED ONLY BY AUTHORISED PERSONNEL
SERVICE MANUAL for BOSTON (MG 3000 STD) SANTA FE (CALGARY, MG 3000 FLS) & ODESSA (PG 3000) GAS FIRES TO BE USED ONLY BY AUTHORISED PERSONNEL PART No 588402 Issue E Nov. 2001 CONTENTS TROUBLESHOOTING Page
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationShort Shifter Installation Instructions For Miata, 6-speed Manual Transmission
Short Shifter Installation Instructions For 2006-15 Miata, 6-speed Manual Transmission PART# 994-060 Required tools: 10mm deep socket Long extension Ratchet Small flathead screwdriver Phillips-head screwdriver
More informationRoll Bar (MMRB-6.1 to -6.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Roll Bar (MMRB-6.1 to -6.7) NOTE: These instructions cover Roll Bars with
More informationHood. Hood, removing, installing and adjusting. Page 1 of 11
Page 1 of 11 55-1 Hood Hood, removing, installing and adjusting 1 - Hood Removing: - Disconnect hose to windshield washer system and unclip. Second person is needed to support and lift hood during removal
More informationRoller Shades CORD LOOP. Head Rail, Fascia and No Head Rail. Installation & Care Instructions
Roller Shades CORD LOOP Head Rail, Fascia and No Head Rail Installation & Care Instructions 152038 H 5/30/2017 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill, drill bits
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual John Deere Track Supported Models 8295RT 8320RT 8345RT PN: 602-0255-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before
More informationINSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING
INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, 76250 Application: 08-NEWER FORD SUPER DUTY Your safety, and the safety of others, is very important. To help you make informed
More informationDrag Race Roll Bar (MMRB-6, -7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Drag Race Roll Bar (MMRB-6, -7) The Maximum Motorsports 6-point Drag Race
More informationSWITCHES PLUNGER TYPE PRIMARY AND SECONDARY LINE SWITCHES AND OUT-TRUNK SWITCHES REQUIREMENTS AND ADJUSTING PROCEDURES
BELL SYSTEM PRACTICES Plant Series SECTION 030-761-701 Issue 2-0, September 1961 AT&TCo Standard SWITCHES PLUNGER TYPE PRIMARY AND SECONDARY LINE SWITCHES AND OUT-TRUNK SWITCHES REQUIREMENTS AND ADJUSTING
More informationDISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.
308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: Moonroof Wind Deflector Nissan Altima PART NUMBER: 999D UZ000 KIT CONTENTS: Item Qty. Description Service Part Number A B C D E F G H 1
More informationOwner s Manual Read and keep this manual. Patents World Wide
Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2006 All Rights Reserved The following manual is provided to assist
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT Thank you for choosing the Motor Trike GL1500 Rake Kit. We ask that you read the directions before you start and follow them very closely.
More informationINSTALLATION GUIDE. KTM RFS Husaberg Polaris 450/525 Outlaw KTM 450/525 XC ATV Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM RFS 03-07 Husaberg Polaris 450/525 Outlaw KTM 450/525 XC ATV 191-833 Manual Revision: 010615 2002 Rekluse Motor Sports Rekluse Motor Sports,
More informationINSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 061810 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise,
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 15 INSTALLATION & OWNER S MANUAL YANMAR Sc2450 cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC2450AS The contents of this envelope are the property of the owner. Be sure to leave
More informationRekluse Motor Sports. The ProStart Clutch. H-D Sportster (2004 +)
Rekluse Motor Sports The ProStart Clutch H-D Sportster (2004 +) Installation Guide Copyright 2006 Rekluse Motor Sports ProStart Revision 1.000 RMS687 H-D Sportster 195-687 Manual Revision: 111308 Rekluse
More informationLIGHT DUTY ROLL UP DOOR
1-800-225-6729 LIGHT DUTY ROLL UP DOOR CAUTION Use proper lifting equipment and correct lifting procedures to avoid damage or injury. MODEL 150C installation guide A rolling door is a large heavy object
More informationTrim (general) Lower A-pillar trim, removing and installing
Page 1 of 16 70-72 Trim (general) Lower A-pillar trim, removing and installing - To remove, remove A-pillar bolts 4 (2x). Tightening torque: 1.5 Nm (13 in. lb) - Remove door seal -2- in area of A-pillar
More informationMaintenance Information
16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More informationInstallation and Care Instructions
WARDS WARDS REPLACE BATTERIES, REPLACE BATTERIES, WARDS WARDS REPLACE BATTERIES, REPLACE BATTERIES, THANK YOU for purchasing a Hunter Douglas Brilliance PowerRise shade. Your new shade has been custom
More information