Sequence of Operation. Installation. Commissioning. Testing and replacement of dampers and actuators. Troubleshooting. Maintenance
|
|
- John Blankenship
- 5 years ago
- Views:
Transcription
1 0 Helgesen Drive, Madison, WI (0) -, (00) -, Fax: (0) - support@renewaire.com Supplemental Instructions for Optional Isolation Dampers for HEX Indoor Models Purpose of this Manual: To instruct how to install isolation dampers for the HEX indoor models. Danger of Electrical Shock when installing dampers on an installed unit. LWYS DISONNET POWER SOURE EFORE INSTLLING! More than one disconnect switch may be required. Installation Dampers are not factory installed but are factory wired. Dampers for this model are designed for installation indoors. Dampers for this model are designed to be installed at the Exhaust ir and Fresh ir locations (See air stream location stickers on side of unit). Remove damper assembly from carton. The motorized actuator is pre-installed and needs no adjusting. Slide damper assembly onto the factory installed round duct collars on the unit at the location(s) described above. NOTE: Position actuator for easy access. Secure damper assembly in appropriate manner. ontinue ducting the unit as described in the Installation and Operation Manual that came with the unit. NOTE: When insulating the duct around damper provide access to the damper actuators, which are located on the outside of the duct, so they can be serviced or inspected in the future. The damper actuators come wired with the appropriate low voltage wire plug. Remove black plastic plug from the side of the unit and the mating low voltage wire plug is located behind this plug. Simply plug the wire connector from the end of the actuator into the wire plug in the unit. NOTE: There is a proper orientation of these plugs in order for them to be correctly mated. lose inspection of the wiring connectors will reveal a notch in the actuator plug and a tab in the unit plug that need to line up for proper connection. Use conduit, strain relief etc. as required by code to secure damper wiring. Sequence of Operation t start-up: Once plugged in, when the ERV unit receives an external call for ventilation, the blowers should not turn on immediately. The isolation dampers are opening inside the duct. It will take less then 0 second for the dampers to open, at which point a low-voltage end switch in the actuator closes. The end switch calls on motor starter to turn on the blower motor. t shut-down: When the ERV no longer calls for ventilation, the isolation dampers will begin closing. Once the dampers are approx. % from closure (-0seconds), the end switches open, and the motors will stop. UTION: lowers may still be spinning. NOTE: Isolation dampers are shut down and in the closed position when the unit is not operating. NOTE: Isolation dampers return to the closed position if power to the unit is interrupted. ommissioning heck all dampers and insure they open and close properly and without binding. pply power to motorized dampers to ensure the actuator opens and closes the damper as designed. NOTE: heck for unobstructed operation. NOTE: For indoor units, the dampers are located inside the ductwork attached to the unit. Therefore, check damper operation after installing the first lengths of ductwork that cover the damper, but before completing the ductwork and making it inaccessible. Testing and replacement of dampers and actuators If dampers fail to open at the signal for ventilation, disconnect power to the unit. To determine if the actuator is defective, disconnect the v power source. onnect the actuator directly to a known v power source with an appropriate cable. If the damper operates correctly, the problem is in the internal wiring connections. Model HEX: if only one motor starter is provided, the damper end switches are connected in series and both actuators need to be checked. Troubleshooting ctuator: Refer to supplied Installation Instructions from manufacturer. Damper: Low air flow: Unit damper(s) not fully open, check for unobstructed operation. lear any obstruction; re-tighten the actuator U-clamp; or replace damper actuator. Dampers open, but blowers don t run: check end switch closure. Maintenance Damper bearing are a nylon material and do not need lubrication. Electrical Schematics See separate Supplemental Wiring Schematics Manual. Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
2 HEXINH /" Overall /" 0 /" Maximum Door Extension lternate ontrol Wiring Inlet /" dia. lternate Power Wiring Inlet /" dia /" ase /" 0 /" Minimum Service rea (Doors can be taken off hinges.) TOP VIEW /" /" Ø " TYP ontrol Wiring Inlet /" dia Damper Wiring Inlet /" dia /" ase Door-interlocked Disconnect Switch Pressure Ports, () /" Overall 0 /" /" /" /" ase O R O R /" /" /" Overall LEFT VIEW Power Wiring Inlet /" dia Damper Wiring Inlet /" dia /" FRONT VIEW RIGHT VIEW HEXINV 0 /" Overall /" /" 0 /" Minimum Service rea (Doors can be taken off hinges.) /" 0 /" Ø " TYP Pressure Ports () TOP VIEW /" ase 0 /" Maximum Door Extension /" Overall /" Overall 0 /" /" R /" ase R O O 0 /" /" " ontrol Wiring Inlet /" Dia. LEFT VIEW Damper Power Wiring Wiring Inlet Inlet /" Dia. /" Dia. /" FRONT VIEW Damper Wiring Inlet /" Dia. /" /" Door-Interlocked Disconnect Switch " Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
3 Non-I Wiring Schematics SHEMTI 0 - HEXIN Models, Single-phase or Three-phase Supply, Dampers SHEMTI - HEXIN Models, Single-phase or Three-phase Supply, Damper Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
4 Non-I Wiring Schematics SHEMTI - HEXIN Models, Single-phase or Three-phase Supply, Damper Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
5 I Wiring Schematics SHEMTI - HEXIN Models, Single-phase or Three-phase Supply, Independent lower ontrol, Dampers SHEMTI - HEXIN Models, Single-phase or Three-phase Supply, Independent lower ontrol, Damper Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
6 I Wiring Schematics SHEMTI - HEXIN Models, Single-phase or Three-phase Supply, Independent lower ontrol, Damper Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
7 EM Wiring Schematics SHEMTI - HEXIN EM Models, Dampers -PHSE POWER SUPPLY - 0 Hz SEE UNIT RTING LEL FOR VOLTGE, M ND MOPD. UNIT DISONNET L T L T L T FUSES (opt.) KEY: "" = Fresh Outside ir lower "" = Exhaust ir lower GND TORY WIRING HIGH-VOLTGE TORY WIRING V FIELD WIRING HIGH-VOLTGE FIELD WIRING V V (/R) () FIELD-INSTLLED SPST SWITHES all for UNIT Operation. all for SPEED TRNSFORMER with ircuit reaker Factory-installed 0K Potentiometer terminals, & set SPEED terminals, & set SPEED T (O/) Factory-installed 0K Potentiometer terminals, & set SPEED T terminals, & set SPEED SEE INSTLLTION ND OPERTION MNUL FOR DDITIONL ONTROL ONNETION INFORMTION S S S S DMPER () DMPER () SHEMTI - HEXIN EM Models, Damper -PHSE POWER SUPPLY - 0 Hz SEE UNIT RTING LEL FOR VOLTGE, M ND MOPD. UNIT DISONNET L T L T L T FUSES (opt.) KEY: "" = Fresh Outside ir lower "" = Exhaust ir lower GND TORY WIRING HIGH-VOLTGE TORY WIRING V FIELD WIRING HIGH-VOLTGE FIELD WIRING V () FIELD-INSTLLED SPST SWITHES all for UNIT Operation. all for SPEED (/R) TRNSFORMER with ircuit reaker V Factory-installed 0K Potentiometer terminals, & set SPEED terminals, & set SPEED T (O/) Factory-installed 0K Potentiometer terminals, & set SPEED T terminals, & set SPEED SEE INSTLLTION ND OPERTION MNUL FOR DDITIONL ONTROL ONNETION INFORMTION S S DMPER () RELY () LEL PN _000 Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
8 EM Wiring Schematics SHEMTI - HEXIN EM Models, Damper -PHSE POWER SUPPLY - 0 Hz SEE UNIT RTING LEL FOR VOLTGE, M ND MOPD. UNIT DISONNET L T L T L T FUSES (opt.) KEY: "" = Fresh Outside ir lower "" = Exhaust ir lower GND TORY WIRING HIGH-VOLTGE TORY WIRING V FIELD WIRING HIGH-VOLTGE FIELD WIRING V () FIELD-INSTLLED SPST SWITHES all for UNIT Operation. all for SPEED (/R) TRNSFORMER with ircuit reaker V Factory-installed 0K Potentiometer terminals, & set SPEED terminals, & set SPEED T (O/) Factory-installed 0K Potentiometer terminals, & set SPEED T terminals, & set SPEED SEE INSTLLTION ND OPERTION MNUL FOR DDITIONL ONTROL ONNETION INFORMTION RELY () S S DMPER () Isolation Dampers HEXIN Due to continuing product development, specifications are subject to change without notice. 0 Renewire LL 0_000 IsolationDampersHEXIN_Mar.indd Revised 0/0 Page
INSTALLATION AND OPERATION MANUAL
0 Helgesen Drive, Madison, WI 78 (608) -99, (800) 67-99, Fax: (608) -8 support@renewaire.com www.renewaire.com INSTALLATION AND OPETION MANUAL HEXINV NOTE: Disconnect Switch and V Transformer Standard
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR
INSTALLATION, OPERATION & MAINTENANE MANUAL ENERGY REOVERY VENTILATOR HE1XIN MODEL: HE1XINV MODEL: HE1XINH WWW.RENEWAIRE.OM ERV HE1XIN TABLE OF ONTENTS HE1XIN info... 2-5 Installation... 6-13 Start-up...14-15
More informationInstallation, Operation & Maintenance Manual ENERGY RECOVERY VENTILATOR HE1.5XIN
Installation, Operation & Maintenance Manual ENERGY REOVERY VENTILATOR HE1.5XIN Model: HE1.5XINH Shown renewaire.com ERV HE1.5XIN TABLE OF ONTENTS HE1.5XIN info... 2-5 Installation... 6-15 Start-up...16-17
More informationINSTALLATION AND OPERATION MANUAL
0 Helgesen Drive, Madison, WI 78 (608) -99, (800) 67-99, Fax: (608) -8 support@renewaire.com www.renewaire.com INSTALLATION AND OPETION MANUAL HEXINV RISK OF FIRE, ELETRI SHOK, OR INJURY. OBSERVE ALL ODES
More informationINSTALLATION AND OPERATION MANUAL HE4XRT RISK OF FIRE, ELECTRIC SHOCK, OR INJURY. OBSERVE ALL CODES AND THE FOLLOWING:
0 Helgesen Drive, Madison, WI 78 (608) -99, (800) 67-99, Fax: (608) -8 support@renewaire.com www.renewaire.com INSTALLATION AND OPETION MANUAL HEXRT RISK OF FIRE, ELETRI SHOK, OR INJURY. OBSERVE ALL ODES
More informationBOOK 4 ELECTRICAL RD2XRT INSTALLATION AND OPERATION MANUAL. Table of Contents ABOUT BOOK 4:
0 Helgesen Drive, Madison, WI, 0.., 00.., Fax: 0.. support@renewaire.com www.renewaire.com RDXRT INSTALLATION AND OPERATION MANUAL BOOK ELETRIAL ABOUT BOOK : This book covers the basic electrical installation
More informationINSTALLATION AND OPERATION MANUAL
0 Helgesen Drive, Madison, WI 78 (608) -99, (800) 67-99, Fax: (608) -8 support@renewaire.com www.renewaire.com INSTALLATION AND OPETION MANUAL HEXRT RISK OF FIRE, ELETRI SHOK, OR INJURY. OBSERVE ALL ODES
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR
INSTALLATION, OPERATION & MAINTENANE MANUAL ENERGY REOVERY VENTILATOR HE1.5XIN MODEL: HE1.5XINH SHOWN RENEWAIRE.OM ERV HE1.5XIN HE1.5XIN INFO TABLE OF ONTENTS HE1.5XIN info... 2-5 Installation... 6-15
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL BYPASS ECONOMIZER OPTION
INSTALLATION, OPETION & MAINTENANCE MANUAL Bypass Economizer Option for: HE1XIN, HE1.5XIN, HE2XIN, HE3XIN, HE4XIN, HE6XIN, HE8XIN WWW.RENEWAIRE.COM IMPORTANT SAFETY INFORMATION WARNING Arc flash and electric
More informationThe newest addition to RenewAire s broad line of Energy Recovery Ventilators.
INTRODUCING HE 1.5X The newest addition to RenewAire s broad line of Energy Recovery Ventilators. The perfect size for the largest number of ventilation applications in the industry: 375-1,400 CFM Advanced
More informationINSTALLATION AND OPERATION MANUAL
S&P USA: Tel (800) 96-770, Fax (800) 96-779, www.solerpalau-usa.com anada: Tel (866) 7-0, Fax (866) 8-6, www.solerpalaucanada.com Mexico: Tel () 900, Fax () 9, www.soler-palau.com.mx INSTALLATION AND OPERATION
More informationF-Series General Specifications
arling F-Series General Specifications F-Series breakers are available up to 700, and are also available with a 25 millivolt metering shunt construction. This optional construction provides a safe method
More informationMake-Before-Break design available in both V- and T-blade switch types. ATTRIBUTES
OEM Equipment Four-Position Sectionalizing Loadbreak Switches GENERL The ooper Power Systems fourposition sectionalizing loadbreak switch is designed for use in transformer (mineral) oil, R-Temp or Envirotemp
More informationSupplemental Manual occupancy sensor MC-C MC-W. TABLE OF CONTENTS Product info... 2 Installation Operation renewaire.
Supplemental Manual occupancy sensor M- M-W M- eiling Mount M-W Wall Mount TABLE OF ONTENTS Product info... Installation... -6 Operation... 7 renewaire.com OUPANY SENSOR Product Info SPEIFIATION Model
More informationInstallation, Operation & Maintenance Manual ENERGY RECOVERY VENTILATOR HE1.5XRT
Installation, Operation & Maintenance Manual ENERGY REOVERY VENTILATOR Model: www.renewaire.com TABLE OF ONTENTS info... 2-5 Installation... 6-17 Start-up...18-19 Maintenance...20-21 ABOUT RENEWAIRE For
More informationINSTALLATION AND OPERATION MANUAL
Soler & Palau USA: Tel (800) 961-7370, Fax (800) 961-7379, www.solerpalau-usa.com anada: Tel (866) 733-0233, Fax (866) 358-5346, www.solerpalaucanada.com Mexico: Tel 52 (222) 2 233 900, Fax 52 (222) 223
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR
INSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR HE2XIN MODEL: HE2XINH MODEL: HE2XINV RENEWAIRE.COM ERV HE2XIN HE2XIN INFO TABLE OF CONTENTS HE2XIN info... 2-6 Installation... 7-
More informationINSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST. For Use with Bard CH Series 3, 4, & 5 Ton Wall Mount Heat Pumps
INSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST MODEL CHCRV-5 For Use with Bard CH Series 3, 4, & 5 Ton Wall Mount Heat Pumps Bard Manufacturing Company, Inc. Bryan, Ohio 43506 Since
More informationLE MODELS: SHIPPING, RIGGING, LIFTING, ASSEMBLY MANUAL
4510 Helgesen Drive, Madison, WI 53718 (608) 221-4499, (800) 627-4499, Fax: (608) 221-2824 LE MODELS: SHIPPING, RIGGING, LIFTING, ASSEMBLY MANUAL This manual provides an overview of shipping, rigging,
More informationGE Industrial Solutions. Limitamp * AR. Arc Resistant Medium Voltage Motor Control. Installation Guide
GE Industrial Solutions Limitamp AR Arc Resistant Medium Voltage Motor ontrol Installation Guide Table of ontents Introduction...3 Opening Medium Voltage oor...3 Medium Voltage oor Latches... Isolation
More informationTECHNICAL GUIDE MODELS: MA MODULAR AIR HANDLERS FOR USE WITH SPLIT SYSTEM COOLING & HEAT PUMP DESCRIPTION FEATURES
TEHNIL GUIDE MODELS: MODULR IR HNDLERS FOR USE WITH SPLIT SYSTEM OOLING & HET PUMP 600-2000 FM BLOWERS 2-5 TON OILS OPTIONL 1 & 3φ ELETRI HETERS ISO 9001 ertified Quality Management System Due to continuous
More informationModel 8144NC Fresh Air Ventilator
Model 8144NC Fresh Air Ventilator Installation and Operating Instructions MOUNTING BRACKETS WIRE ENTRY LOCATION INTEGRAL PRESSURE PORTS (PORT ON INLET SIDE NOT SHOWN) OVAL OUTLET COLLAR FOR 6" DIAMETER
More informationPRO-14 EVO DIRECT FIRE CAPACITOR DISCHARGE IGNITION
PRO-1 EVO IRET FIRE PITOR ISHRGE IGNITION PLESE REPORT NY ERRORS SLES@MWIGNITIONS.OM ONTENTS: 1. Installation notes. Ignition coil information. Mounting dimensions. onnections and specifications 5. Wiring
More informationDTC C1268/68 Transfer "L4" Position Switch Circuit
RKE ONTROL VEHILE STILITY ONTROL SYSTEM 135 DT 1268/68 Transfer "L4" Position Switch ircuit DESRIPTION fter confirming that the transfer is in the L4 position, -TR and downhill assist control will be activated
More informationPro-14 4 CHANNEL CAPACITOR DISCHARGE IGNITION
Pro-14 4 HNNEL PITOR ISHRGE IGNITION pplicable S/No s 34xxxx ONTENTS: 2. Installation notes 6. Ignition coil information 7. onnections and specifications 8. 4 coil direct fire ignition 9. 4 coil waste
More informationDPST-NO None 2 channels Auto-reset Inverse 24 VAC/VDC G9SB-2002-A 4 1 channel or 2
Sfety Rely Unit Ultr Slim Sfety Rely Unit Models of width 17.5 mm vilble with 2 or 3 poles. Models of width 22.5 mm with 3 poles lso vilble. Conforms to EN stndrds. (TÜV pprovl) DIN trck mounting possible.
More informationInstallation, Operation and Maintenance Manual
Document 458295 Automatic Fire Damper Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR
INSTALLATION, OPETION & MAINTENANE MANUAL ENERGY REOVERY VENTILATOR HE1.5XRT MODEL: HE1.5XRT WWW.RENEWAIRE.OM HE1.5XRT HE1.5XRT INFO TABLE OF ONTENTS HE1.5XRT info... 2-7 Installation... 8-19 Start-up...20-21
More informationINSTALLATION INSTRUCTIONS
MiniCOREVentilator ENERGY RECOVERY CORE INSTALLATION INSTRUCTIONS MC500-1ERV JANUARY 10, 2018 SUPERSEDES: NONE INSTALLATION INSTRUCTIONS FOR MINICORE VENTILATOR (MCV) WITH FACTORY INSTALLED OPTIONS USED
More informationPK Installation Instructions for the 2CPS Series Cable Pull Switch Without Broken Cable Detection ISSUE 3. Sensing and Control
ISSUE 3 Installation Instructions for the 2PS Series able Pull Switch Without roken able Detection PK 80169 WRNING IF USED IN PPLITIONS ONERNING HUMN SFETY Only use N direct opening ( positive opening
More informationINSTALLATION AND OPERATION MANUAL
4510 Helgesen Drive, Madison, WI 53718 (608) 221-4499, (800) 627-4499, Fax: (608) 221-2824 support@renewaire.com www.renewaire.com INSTALLATION AND OPERATION MANUAL EV450IN RISK OF FIRE, ELECTRIC SHOCK,
More informationPro-Drag4R 2 Rotor 250mJ S4
Pro-rag4R 2 Rotor 250mJ S4 ELETRIL WIRING & OPERTING INSTRUTIONS pplicable S/No s 89xxxx FILURE TO FOLLOW INSTRUTIONS WILL VOI WRRNTY ONTENTS: 2. Installation notes 6. onnections and specifications 7.
More information7900 SERIES CONTROL BOXES
7900 SERIES CONTROL BOXES CONTROL BOXES Heavy duty, surface mounted control box contains one or two electrically controlled pneumatic circuits. ir filtration, pneumatic regulation, and system timing is
More informationPro-Drag4R 4 CHANNEL (2 ROTOR) 250mJ CAPACITOR DISCHARGE IGNITION
Pro-ragR HNNEL ( ROTOR) 50mJ PITOR ISHRGE IGNITION PLESE REPORT NY OMISSIONS SLES@MWIGNITIONS.OM ONTENTS: 1. Installation notes. Ignition coil information. Mounting dimensions. onnections & Specifications
More informationPro-12 2 CHANNEL CAPACITOR DISCHARGE IGNITION
Pro-12 2 HNNEL PITOR ISHRGE IGNITION pplicable S/No s 36xxxx ONTENTS: 2. Installation notes 6. Ignition coil information 7. onnections and specifications 8. 2 coil waste spark ignition 9. 4 coil waste
More informationINSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST. For Use with Bard 2 2-1/2 Ton Wall Mount T Series Heat Pumps
INSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST MODELS CRVMWH-3 For Use with Bard 2 2-1/2 Ton Wall Mount T Series Heat Pumps Bard Manufacturing Company, Inc. Bryan, Ohio 43506 Since
More informationfor Untempered - Make-Up Air Units
Part # 457646 Installation, Operation, and Maintenance Instructions for Untempered - Make-Up ir Units Table of Contents Installation............................. 2-5 Troubleshooting..........................
More informationVERTICAL MULTISTAGE PUMPS
Record the following information from the motor and pump nameplates for future reference: Model No. Bill of Material No. Model No. Serial No. HP Rated mp Draw Volts/Hz/Ph PVM(X) SRIS VRTIL MULTISTG PUMPS
More informationMODEL SCA Installation and Operation Manual Important:
MODEL SCA Installation and Operation Manual Important: This manual contains specific cautionary statements relative to worker safety. Read this manual thoroughly and follow as directed. It is impossible
More informationXENON POWER SUPPLY 4000 Watt Gladiator IV
XENON POWER SUPPLY 4000 Watt Gladiator IV 220 Volt Equipment Type 62-00049 Rev. February 2003 STRONG INTERNATIONAL a division of Ballantyne of Omaha, Inc. 4350 McKinley Street Omaha, Nebraska 68112 USA
More informationADVANCE PRODUCT SERVICE INFORMATION
DVNE PRODUT SERVE NORMTON SUBJET: Electronic uel Management (EM) System - Update No: 60 Revised DTE: 10/09 MODELS: M40/44/49 This PS is an update and replacement for PS #60 dated 5/09. t includes additional
More informationOperators Manual SUREFIRE II Single Phase PDI - SLR (24VDC, 115VAC & 230VAC) r#2
Operators Manual SUREFIRE II Single Phase PDI - SLR (24VD, 115VA & 230VA) 36412 r#2 ontents Precautions & Symbols...2 Manufacturer s Statement...2 General...2 Features...2 Operation...3-4 Technical Data...5
More informationMODEL SMZ-SW ZONE CONTROL SYSTEM
DuroZone MODEL SMZ-SW ZONE ONTROL SYSTEM DuroZone is a division of orporation PART# 35226 PART# 35227 SMZ-2SW/SMZ-3SW INSTALLATION INSTRUTIONS ongratulations on purchasing a DuroZone SMZ ontrol System.
More informationFSD60, FSD60LP COMBINATION FIRE AND SMOKE DAMPER 1 1 /2 HOUR UL555 RATED, UL555S LEAKAGE CLASS 1
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FX (816) 765-8955 FSD60, FSD60LP COMINTION FIRE ND SMOKE DMPER 1 1 /2 HOUR UL555 RTED, UL555S LEKGE CLSS 1 PPLICTION Ruskin FSD60 Series ultra
More informationMotorized Rotary Actuator Type 3001
Motorized Rotary ctuator Type 00 dvantages/benefits 5 m nominal torque Open/closed with choice of rotation speeds Flange interface ISO 5 IP 65 rating orrosion resistant vailable with manual override Optical
More informationThe IAQ50 Air Damper/Monitor Installation and Maintenance Manual
The IAQ50 Air Damper/Monitor Installation and Maintenance Manual RUSKIN MANUFACTURING 3900 Dr. Greaves Road Kansas City, Missouri 64030-1183 U.S.A. ! WARNING DO NOT TAMPER WITH (REMOVE, REPLACE, RELOCATE
More informationSurepowr Series Sure 150
RCS Acutators Surepowr Series Sure 50 Installation Manual Safety First In the maintenance and operation of mechanical equipment, safety is the basic factor which must be considered at all times. Through
More informationCOOPER POWER SERIES. Sectionalizing switch installation instructions. OEM Equipment MN800002EN. Effective March 2016 Supersedes June 2015
OEM Equipment MN800002EN Effective March 2016 Supersedes June 2015 Sectionalizing switch installation instructions OOPER POWER SERIES DISLIMER OF WRRNTIES ND LIMITTION OF LIILITY The information, recommendations,
More informationCB29M. Multi Position 60 HZ A I R H A N D L E R S. 3 to 5 Tons Optional Electric Heat 5 to 30 kw CB 29 M 41 1 E N G I N E E R I N G D A T A
E N G I N E E R I N G D T I R H N D L E R S CB29M Multi Position 60 HZ Bulletin No. 210478 November 2008 Supersedes July 2007 3 to 5 Tons Optional Electric Heat 5 to 30 kw MODEL NUMBER IDENTIFICTION CB
More informationK*ES120 DESCRIPTION TECHNICAL GUIDE SPLIT-SYSTEM EVAPORATOR BLOWERS 10 NOMINAL TONS EER 8.5 ACCESSORIES FIELD INSTALLED TABLE 1: ARI RATINGS*
TECHNICL GUIDE SPLIT-SYSTEM EVPORTOR LOWERS K*ES120 10 NOMINL TONS EER 8.5 DESCRIPTION These completely assembled dual circuit evaporator blower units include a well-insulated cabinet, a DX cooling coil
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More informationC&K 8060 Series Alternate Action and Momentary Pushbutton Switches
lternate ction and Momentary Switches Specifications CONTCT RTING: Q contact material: 6 MPS @ 120 V C or 28 V DC; 3 MPS @ 250 V C. See page -53 for additional ratings. ELECTRICL LIFE: 50,000 make-and-break
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR
INSTALLATION, OPETION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR HE2XRT MODEL: HE2XRT RENEWAIRE.COM HE2XRT ABOUT RENEWAIRE For over 30 years, RenewAire has been a pioneer in enhancing indoor air quality
More informationØ5/16" HOLES FOR FASTENING TO CURB
SIDE INTKE SUPPLY UNIT / SIDE INTKE GLVNIZED SUPPLY UNIT OPERTION INSTRUCTIONS ND PRTS MNUL SIS SERIES MODELS: SIS-9, SIS-10, SIS-12, SIS-15, SIS-18, SIS-20 SIG SERIES MODEL: SIG-9, SIG-10, SIG-12, SIG-15
More information! WARNING. Series LPC-2000 General Purpose Liquid Level Controls. Installation & Maintenance Instructions MM-106 (B)
Installation & aintenance Instructions -0 (B) Series LP-000 General Purpose Liquid Level ontrols For use with Series RS or Series S Remote Sensors (sold separately) pplications: For tank, hydronic and
More information8060 Series Alternate Action and Momentary Pushbutton Switches
lternate ction and Momentary Switches Features/Benefits Long travel vailable with LED Long life contact design Epoxy terminal seal compatabile with bottom wash cleaning RoHS compliant models available
More informationPRO-16 6 CHANNEL CAPACITOR DISCHARGE IGNITION
PRO- HNNEL PITOR ISHRGE IGNITION ONTENTS: PLESE REPORT NY OMISSIONS OR ERRORS TO SLES@M.OM. aution. Installation notes, Ignition coil information. Mounting dimensions. onnections and specifications 0.
More informationPro-14R 2 Rotor 115mJ Series 3
Pro-14R 2 Rotor 115mJ Series 3 pplicable S/No s 41xxxx ONTENTS: 2. Installation notes 6. Ignition coil information 7. onnections & Specifications 8. irect fire rotary ignition 9. irect fire reciprocating
More informationGeneral Specifications
Series FB & SB Momentary Pushbuttons General Specifications FB Series Electrical apacity (Resistive Load) Power Level: 500mA @ 125V A for silver Logic Level: 0.4VA max. @ 28V A/D max. for gold (Applicable
More informationULTRA-ZONE FORCED AIR ZONE CONTROLS EWC
INDEX DAMPERS MOTORIZED MODEL RSD ROUND... 7-5 MODEL URD ROUND... 7-5 ND SERIES... 7-6 7-7 STATIC PRESSURE CONTROL MODEL EBD RECTANGULAR... 7-7 MODEL EBD ROUND... 7-7 MODEL PRD... 7-8 MODEL PRD-RD... 7-8
More informationVB-7000 Series. Selection Guide. Applications. Applicable Literature. Selection Guide Contents
V-7000 Series Selection Guide T V-7000 Series 1/2 to 2 Globe Vlves with Fort M400, M800, nd M1500 ctutors pplictions T Fort M400, M800, nd M1500 series liner ctutors mount directly 1 onto 1/2 to 2 V-7xxx
More informationTECHNICAL GUIDE MODELS: MV MODULAR VARIABLE SPEED AIR HANDLERS FOR USE WITH SPLIT SYSTEM COOLING & HEAT PUMP DESCRIPTION FEATURES
TEHNIL GUIDE MODELS: MV MODULR VRIBLE SPEED IR HNDLERS FOR USE WITH SPLIT SYSTEM OOLING & HET PUMP 1200-2000 FM BLOWERS 3-5 TON OILS OPTIONL 1 & 3 ELETRI HETERS Due to continuous product improvement, specifications
More informationINSTALLATION & OPERATION MANUAL. Fan Powered Terminals VAV TERMINALS. Redefine your comfort zone.
INSTALLATION & OPERATION MANUAL Fan Powered Terminals VAV TERMINALS IOM FAN POWERED TERMINALS Receiving Inspection After unpacking the terminal, check it for shipping damage. If any shipping damage is
More informationGREEN REFRIGERANT R-410A
WLL-MOUNT -TON IR CONDITIONERS J7 - Right Side Control Panel J7L - Left Side Control Panel, 9.5 EER Hz Solair Wall-Mount ir Conditioner is a self contained energy efficient system, which is designed to
More informationInstallation and Maintenance. DuctMaster Circular Axial Flow Fans. Contents. Page ... General Description. Introduction
DuctMaster ircular xial Flow Fans Installation and Maintenance Nuire Limited, Western Industrial Estate, aerphilly, Mid Glamorgan, F83 1XH. United Kingdom. Telephone: 01222 885911 Fax: 01222 887033 Email:
More informationPowerUV. PowerUV MAX. PowerUV STD. PowerUV ENT. PowerUV SPC. Electronic Ballasts for Standard, High output (HO) And Amalgan Germicical UV lamps
UV PowerUV STD UV PowerUV MX 50W to 90W High Output & Standard Lamps (800 m & 425m) Dual or Single Lamp Operation Universal & Dedicated Input Voltage Options - Power On LED, Lamp Out Buzzer UV PowerUV
More information6 8 Magnum 40(x) Maintenance Instructions
RE INSTRUTIONS IN FULL EFORE INSTLLTION. QUESTIONS? LL 916-760-4524 M-F 8:00 M 4:30 PM PST t ackflow irect we are committed to making our products as easy to install as possible. We design for most contingencies,
More informationHeadlight Module Conversion Kit
II #0317 pplication: 1984-1987 4 orvette Headlight Module onversion Kit Part Includes 1 - onversion Kit Tools Needed PREUTIONS Do not energize the ontroller until all wiring changes are complete and proper.
More informationINSTALLATION VARIABLE FREQUENCY DRIVE THREE PHASE ALX SERIES SPUN ALUMINUM EXHAUSTERS
SPUN ALUMINUM EXHAUSTER OPERATION INSTRUCTIONS AND PARTS MANUAL READ AND SAVE THESE INSTRUCTIONS The purpose of this manual is to aid in the proper installation and operation of the blowers. These instructions
More informationINSTALLATION INSTRUCTIONS Low Rise Car Lift
INSTLLTION INSTRUTIONS Low Rise ar Lift TL07 apacity 7000 lbs. (Maximum 1750 lbs. per pad) TL10 apacity 10,000 lbs. (Maximum 2500 lbs. per pad) January 2016. ll rights reserved. O9648 1010905 Rev. J 1/08/2016
More informationXENON POWER SUPPLY Watt
XENON POWER SUPPLY 3000-5000 Watt 220 Volt Equipment Type 62-00016 62-00017 62-00004 (Export) Rev. February 2006 STRONG INTERNATIONAL a division of Ballantyne of Omaha, Inc. 4350 McKinley Street Omaha,
More informationTitle 24 Compliant P2 Lighting Panel
Title 24 ompliant P2 Lighting Panel ustomizable lighting panels to meet various Disaggregation requirements alifornia Title 24 and other Disaggregation Solutions Siemens has designed an easy to install
More informationFD68 BURNERS SELECTION GUIDE & ENGINEERING SPECS
SELECTION GUIDE The following data can be used to fill in the information appropriate for the burner size required: FD68 C A 150 L M BD FORCED DRAFT MODEL 68 FUEL A-OIL ONLY G-GAS ONLY C-GAS/OIL TYPE OF
More informationDTC B1810/53 Short in Driver Side Squib 2nd Step Circuit. DTC B1811/53 Open in Driver Side Squib 2nd Step Circuit
184 SUPPLEMENTL RESTRINT SYSTEM IRG SYSTEM DT 1810/53 Short in Driver Side Squib 2nd Step ircuit DT 1811/53 Open in Driver Side Squib 2nd Step ircuit DT 1812/53 DT 1813/53 Short to GND in Driver Side Squib
More informationGeneral Specifications
Series FB & SB Momentary Pushbuttons General Specifications FB Series Electrical apacity (Resistive Load) Power Level: 500mA @ 125V A for silver Logic Level: 0.4VA max. @ 28V A/D max. for gold (Applicable
More informationTYPICAL SWITCH ORDERING EXAMPLE A2 G 40. Contact Materials & Ratings
MB4 s & ircuits SPDT ON (ON) DPDT ON (ON) ( ) = Momentary E E S S Bushings Smooth with D Flat Threaded with D Flat IMPORTNT: Switches are supplied without UL, culus & S marking unless specified. UL, culus
More informationProduct Data Manual. ERV5000i/e ERV6500i/e ERV8000i/e ERV10000i/e
Product ata Manual ERV5000i/e ERV6500i/e ERV8000i/e ERV10000i/e Table of Contents Physical ata - Nomenclature Options............................................. 3 Effectiveness Performance ata.................................................
More informationGeneral Specifications
Series M eneral Specifications Miniature Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical apacity (Resistive Load)
More informationCALL HEIGHT CARD READER TOP OF MONITOR FRONT SIDE CONCRETE SURFACE TO BE FLAT AND LEVEL IN AREA OF UNIT
R OPTEV 5 EXTERIOR SH DISPENSER 5 HIGH ND mm ( ") SFE L009 LL -800-999-600 HEIGHT DEPTH 65 TOP FUNTION KEY 06 (4 ") 8 ( (4 8 ") 89 (5 4 ") (4 8 ") (5 9 8 ") ( 98 8 ") (8 D E RD REDER REEIPT PRINTER DVNED
More informationFSD36, FSD36LP COMBINATION FIRE AND SMOKE DAMPER
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FX (816) 765-8955 FSD36, FSD36LP COMINTION FIRE ND SMOKE DMPER 1 1 /2 HOUR UL555 RTED, UL555S LEKGE CLSS 2 PPLICTION Ruskin FSD36 Series low leakage
More informationInstallation, Operation, and Maintenance Manual. Automatic Fire Damper
Installation, Operation, and Maintenance Manual Automatic Fire Damper Part # 458295 Designed to close in fire situations. Reset by activating the reset switch. UL Listed Constructed in Accordance with
More informationG7150D, 3-Way, Diverting Flanged Globe Valve
G7150D, 3-ay, Diverting Flanged Globe Valve pplication This valve is typically used in Large ir Handling Units on heating or cooling coils. This valve is suitable for use in a hydronic system with variable
More informationPin & Sleeve. Heavy Duty Industrial Wiring Devices for North American and European Markets
Pin & Sleeve Heavy Duty Industrial Wiring Devices for North merican and European Markets Pin & Sleeve SFETY, PERFORMNE ND DURILITY...IN SNP! Extensive Product Family: - Safe and reliable, portable electrical
More informationBURNISHER ANTI-VIBRATION KIT
56383233 URNISHER NTI-VIRTION KIT Item Ref. No. Qty Description [ ] 56090160 1 Instruction Sheet 1 56001878 1 Scr-Hex 1/4-20 X 1.25 2# DELETED 3# 56109766 2 Screw utton Head 1/4-20 X.63 4 56002155 4 Scr-Hex
More informationINSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST. For Use with Bard C**H Series 2 & 2½ Ton 2-Stage Wall Mount Heat Pumps
INSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST MODEL CHCRV-3 For Use with Bard C**H Series 2 & 2½ Ton 2-Stage Wall Mount Heat Pumps NOTE: CHCRV-3 Models must be installed with TCURB
More informationINSTALLATION INSTRUCTIONS FOR PRO-16B S3 6 CHANNEL CAPACITOR DISCHARGE IGNITION
INSTLLTION INSTRUTIONS FOR PRO-6 S 6 HNNEL PITOR ISHRGE IGNITION PLESE REPORT NY OMISSIONS OR ERRORS TO SLES@MWIGNITIONS.OM ONTENTS:. Installation notes. Ignition coil information. Mounting dimensions.
More informationWall Hoods INSTALLING HOOD CANOPY. Island Hoods
HEIGHT OF HOOD The bottom of the hood to should be 30 (76.2 cm) to 36 (91.4 cm) above the countertop. This would typically result in the bottom of the hood being 66 (167.6 cm) to 72 (182.9 cm) above the
More informationVB-7000 Series 1/2 to 2 Globe Valves
V-7000 Series 1/2 to 2 Globe Valves with MG350V Series SmartX ctuators schneider-electric.com 1 Product Description Schneider Electric MG350V non-spring actuators and V-7000 series two and three-way globe
More informationHeat Exchanger Accessories
TEMPERTURE CONTROL - SERIES 123W May be used directly to control small electric motors etc using SINGLE phase power supply to maximum of 6 amps. lso for low volt (12 or 24) DC power supplies to maximum
More informationSafety Relay Unit. Ordering Information. Ultra Slim Safety Relay
Sfety Rely Unit Ultr Slim Sfety Rely Unit Models of width 17.5 mm (smllest Unit in the world s of Jnury 2001) vilble with 2 or 3 poles. Models of width 22.5 mm with 3 poles lso vilble. EN stndrds (TÜV
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR
INSTALLATION, OPERATION & MAINTENANCE MANUAL ENERGY RECOVERY VENTILATOR MODEL: RENEWAIRE.COM INFO TABLE OF CONTENTS info... 2-4 Installation... 5-13 Start-up & Operation...14-17 Maintenance...18-19 CONFIGURATION
More informationATB Series Integral Throttle Body Actuators
T Series Integral Throttle ody ctuators 1 INTROUTION The T Series integral throttle body electric actuators are designed to control the air or air/fuel mixture to a gas or gaseous-fueled engine. They are
More informationINSPECTION. If error is excessive, replace the speedometer.
US (mph) ODY ELETRIL 4WD 2WD M/T 2WD /T E39 E24J01 INSPETION 1. INSPET SPEEDOMETER ONVEHILE Using a speedometer tester, inspect the speedometer for allowable indication error and check the operation of
More informationTROUBLESHOOTING GUIDE FOR HEAT PUMP BOOSTERS MODELS: HPB11, HPB15, & HPB22
V3 TROUBLESHOOTING GUIDE FOR HEAT PUMP BOOSTERS MODELS: HPB11, HPB15, & HPB22 PREFACE This guide contains instructions for troubleshooting the Steffes Corporation room heating units: Models HPB 11, HPB
More informationMorris Products 53 Carey Road, Queensbury, NY 12804
Catalog Number 790 UPC Number 60986790 Description Low Profile Emergency Lighting allast 500 Lumen T5 & T8 Fixtures Features For both normal and emergency Flourescent lighting. In the event of a Power
More informationVERTICAL MULTISTAGE PUMPS
Record the following information from the motor and pump nameplates for future reference: Model No. Bill of Material No. Model No. Serial No. HP Rated mp Draw Volts/Hz/Ph PVM(X) SRIS VRTIL MULTISTG PUMPS
More informationInstallation, Start-Up and Service Instructions
62MB,MC,MD,ME040-950 Energy Recovery Ventilators Installation, Start-Up and Service Instructions CONTENTS Page SFETY CONSIDERTIONS...1 INTRODUCTION...1 INSTLLTION... 1-58 Step 1 Inspection...1 Step 2 Install
More informationEncore S28/L28/S33/L33/S38/L38. Section II. Parts and Service Manual (79049B)
Encore S8/L8/S/L/S8/L8 Section II Parts and Service Manual (9049B) CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8 - - HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM CAUSE ACTION The machine
More informationEnergy Recovery Ventilator
PEG1610044CE Version:1601 Service Mnul Energy Recovery Ventiltor (North meric Mrket) WRNING This service informtion is designed for experienced repir technicins only nd is not designed for use by the generl
More information42AM. Air heaters. product selection. the best solution for heating large spaces. ensures buildings warm up ultra-fast
product selection the best solution for heating large spaces ensures buildings warm up ultra-fast excellent diffusion via patented JET+ double deflection technology ir heaters 4M Translation of the original
More information