General Specifications

Transcription

1 Standard Size Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 125V AC or 250V AC or 30V C Logic Level (gold): 0.4VA 28V AC/C maximum (Applicable Range 0.1mA ~ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold Insulation Resistance: 200 megohms 500V C ielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit Electrical Life: 100,000 operations minimum Nominal Operating Force: 4.41N Contact Timing: Nonshorting (break-before-make) Travel: Pretravel.059 (1.5mm); Overtravel.059 (1.5mm); Total Travel.118 (3.0mm) Materials & Finishes Housing: Snap-in Frame: Movable Contact: Stationary Contacts: Base: Switch Terminals: Lamp Terminals: Environmental ata Operating Temperature Range: Humidity: Vibration: Shock: Sealing: Installation Cap Installation Force: Quick Connect Force: Soldering Time & Temperature: Standards & Certifications Flammability Standards: UL: CSA: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Silver alloy or copper with gold plating Silver alloy or copper with gold plating Liquid crystal polymer (UL94V-0) Phosphor bronze with silver or gold plating Brass with silver plating 25 C through +50 C ( 13 F through +122 F) for Illuminated 25 C through +70 C ( 13 F through +158 F) for Nonilluminated Note: used with a polyvinyl chloride splash cover, the lowest limit is 0 C (32 F) 90 ~ 95% humidity for C (104 F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Not available for snap-in; see next section for panel seal. 3.92N maximum downward force on cap 52.95N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. UL94V-0 housing & base File No. E Recognized only when ordered with marking on switch. Add /U or /CUL before first dash in part number to order UL recognized switch. All models recognized at 125V or 250V AC or 28V AC/C maximum. File No _0_000 - Certified only when ordered with marking on switch. Add /C before first dash in part number to order CSA certified switch. All models certified at 125V or 250V AC or 28V AC/C maximum. 46

2 Standard Size Pushbuttons Series LB istinctive Characteristics Carefully designed light diffusion and filtering system produces bright, full surface illumination with front panel relamping. Spot illumination available in single and bicolor LEs. Choice of super bright LEs in white, green, and blue in addition to standard or bright red, amber, and green LEs. Stainless steel clips provide secure mounting with a wide range of panel thicknesses. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Snap-action contact mechanism gives long electrical life and sensitivity of actuation. Combination solder lug and.110 quick connect terminals are epoxy sealed to prevent entry of flux, dust, and other contaminants. Panel sealed model meets IP65 of IEC60529 specifications (similar to NEMA 4 & 13). Compact switch design minimizes behind panel depth. Matching indicators available. Actual Size Snap-in Mount Panel Seal Page 46 Page 57 47

3 Standard Size Snap-in Pushbuttons LB Poles 1 SPT 2 PT 1 5 S K W01 Circuits 5 () ( ) = Momentary 6 Alternate Action with Latchdown IMPORTANT: S C R Shapes Switches are supplied without UL, culus and CSA marking unless specified. UL, culus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, and ordering instructions are noted on the General Specifications page. Red, 12-volt, Bright LE with Resistor SPT -() Circuit Silver Contacts Rated 125/250V AC; Solder Lug/Quick Connect Terminals K G W01 G01 ESCRIPTI FOR TYPICAL ORERING EXAMPLE LB15SKW01-5C12- Housing Black Gray Clear Cap with Red iffuser Shape Black Housing TYPICAL SWITCH Contacts & Terminals Silver Contacts Rated 125/250V AC Solder Lug/Quick Connect Terminals Gold Contacts Rated 28V AC/C Solder Lug/Quick Connect Terminals 48

4 Standard Size Snap-in Pushbuttons Series LB ORERING EXAMPLE 5C 12 Incandescent Lamp Used with Solid Cap 05 5-volt volt No Code Nonilluminated Incandescent or Neon Used with Insert Cap volt Neon 05 5-volt Incandescent volt Incandescent No Code 5C 5 5F 6B 6F 6G 1C 1 1F CF No Code Bright LE Used with LE Cap Colors Red Amber Green Super Bright LE Used with LE Cap White Green Blue Lamps Nonilluminated No Code Resistor 05 5-volt No Resistor volt volt LE in Spot Illuminated Cap Red Single Color Amber Single Color Green Single Color Red/Green Bicolor Nonilluminated Nonilluminated BJ CJ EJ FJ GJ JE *JF *JG J JF A B C F Cap Types & Colors Solid Cap: Lens/Filter Colors White/Clear Red/Clear Yellow/Clear Green/Clear Blue/Clear Insert Cap: Lens/Filter Colors Clear/White Clear/Red Clear/Yellow Clear/Green Clear/Blue *JF & JG not suitable with neon. LE Cap: Lens/iffuser Colors Clear/White Clear/Red Clear/Amber Clear/Green LE Cap: Lens/iffuser Colors Clear/White Spot Illuminated Cap Colors Black White Red Green Available in and only. Nonilluminated Cap Colors A Black F Green B White G Blue C Red H Gray E Yellow 49

5 Standard Size Snap-in Pushbuttons Pole SP P S Housing Colors Available: W01 G01 Model LB15 *LB16 LB25 *LB26 * in latchdown position for the alternate circuit, cap position is.039 (1.0mm) above the built-in bezel..622 (15.8mm) (16.2) Sq.638 Cutout for 1 switch:.638 x.638 (16.2mm x 16.2mm) Cutout for 1 switch with barriers:.638 x.815 (16.2mm x 20.7mm) Silver Contacts Gold Contacts C SHAPES & PANEL CUTOUTS.854 (21.7mm) K HOUSING CTACT MATERIALS, RATINGS & TERMINALS Power Level 125V AC & 250V AC (1.5) R.059 Logic Level 0.4VA 28V AC/C max. (22.0) ia.866 Panel Thickness for Switches & Barriers:.039 ~.157 (1.0 ~ 4.0mm) Panel Thickness for s & Splash Covers:.039 ~ (1.0 ~ 3.5mm) Black Complete explanation of operating range in Supplement section. AT607 & AT607N T-1 Bi-pin Plunger Position ( ) = Momentary Connected Terminals Throw & Switch/Lamp Schematics Normal own Normal own Notes: Switch is marked with,,, L+, L. Lamp circuit is isolated and requires an external power source. () () AT607 Incandescent 5-volt or 12-volt; AT607N Neon 110-volt POLES & CIRCUITS SPT PT (11.5).453 R G Solder Lug/Quick Connect Voltage V 5V AC 12V AC 110V AC Current I 115mA 60mA 1.5mA Endurance Avg. Hours 10,000 10,000 Ambient Temp. Range C ~ +50 C x.866 (15.8mm x 22.0mm) Epoxy Seal (22.4).882 (2.0).079 (2.8).110 (1.2).047 Thk = (0.5) The electrical specifications shown are determined at a basic temperature of 25 C. Lamp circuit is isolated and requires external power source. * Recommended Resistors for Neon: 33K ohms for 110V AC; 100K ohms for 220V AC (16.2).638 Cutout for 1 switch:.638 x.882 (16.2mm x 22.4mm) Cutout for 1 switch with barriers:.638 x (16.2mm x 26.9mm) Gray Optional PCB adaptors AT711 & AT712 available; illustrated in Optional Accessories immediately following Typical Switch imensions. IANESCENT & NE LAMP COES & SPECIFICATIS 01 * (-) L (-) L 50

6 Standard Size Snap-in Pushbuttons Series LB AT635 LEs are colored in OFF state. AT627 with Resistor AT627 5-volt 4-element with Resistor AT625G Blue AT631B White AT632F Green No Code (+) (-) T Bi-pin T-1 Bi-pin LE COLORS & SPECIFICATIS The electrical specifications shown are determined at a basic temperature of 25 C. LE circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. (+) (-) (+) (-) T-1 Bi-pin No Lamp Color Codes Bright LE without Resistor (+) (-) Red Amber Green Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current I F 20mA 20mA 20mA Forward Voltage V F 1.9V 2.0V 2.1V Maximum Reverse Voltage V RM 5V 5V 5V Current Reduction Rate Above 25 C I F 0.42mA/ C Ambient Temperature Range Color Codes: AT volt 4-element with Resistor Red Amber Green 5C 5 5F Bright LE with Resistor Super Bright Single Element LE No Code 25 ~ +50 C No Resistor Color White Green Blue Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current I F 20mA 20mA 20mA Forward Voltage V F 3.3V 3.3V 3.3V Maximum Reverse Voltage V RM 7V 7V 7V Current Reduction Rate Above 25 C I F 0.40mA/ C 0.40mA/ C 0.40mA/ C Ambient Temperature Range AT volt 4-element with Resistor 6B Resistor Codes Maximum Forward Current I FM Typical Forward Current I F 52mA 26mA 13mA Forward Voltage V F 5V 12V 24V Maximum Reverse Voltage V RM 4V 8V 16V Current Reduction Rate Above 25 C I F 0.50mA/ C Ambient Temperature Range Red Amber Green 5C 5 5F ATTENTI ELECTROSTATIC SENSITIVE EVICES 25 ~ +50 C (+) 6F 25 ~ +50 C 6G (-) 51

7 Standard Size Snap-in Pushbuttons Lens/Filter Colors Available: BJ CJ EJ FJ GJ Lens/Filter Colors Available: JE JF and JG not suitable with neon lamp. AT476 CAP TYPES & COLOR BINATIS Color Codes: B White C Red Amber E Yellow F Green G Blue J Clear JF JG Lens/iffuser Colors Available: J JF Lens/iffuser Colors Available: J JF AT4176 AT4162 AT477 Solid Cap for Incandescent Lamp & Nonilluminated AT4012 Material: Polycarbonate AT4013 Material: Polycarbonate Insert Cap for Incandescent or Neon Lamp & Nonilluminated (19.0) ia (19.0) ia AT4178 Material: Polycarbonate Cap for Bright LE without Resistor (19.0) ia Material: Polycarbonate Cap for Bright LE with Resistor (19.0) ia AT4164 (5.5 AT4026 AT4027 AT4177 AT4163 Translucent Colored Lens Transparent Clear Filter Lamp AT607 Transparent Clear Lens Translucent Colored Filter Lamp AT607 or 607N Transparent Clear Lens Translucent Colored iffuser Bright LE AT635 Transparent Clear Lens Translucent Colored iffuser Bright LE AT627 52

8 Standard Size Snap-in Pushbuttons Series LB CAP TYPES & COLOR BINATIS Color Codes: A Black B White C Red Amber E Yellow F Green G Blue H Gray J Clear Material: Polycarbonate Clear Lens White iffuser AT4129 (19.0) ia Cap for Super Bright LEs AT4128 Spot Illuminated Cap with LE AT4130 Transparent Clear Lens Translucent White iffuser LEs AT625 AT631 AT632 The electrical specifications shown are determined at a basic temperature of 25 C. LE circuit is isolated and requires an external power source. Single color LEs are colored in OFF state; bicolor LEs are translucent white in OFF state. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. LE factory assembled in Spot Illuminated Caps Not Available Separately Cap Colors Available: A B C F Material: Polycarbonate Cap Colors Available: A B C E F G AT480 Single Color AT4016 ordering spot illuminated cap separately, LE color must be specified. Examples: AT480CA (red LE, black cap); AT4016CFB (red/green bicolored LE, white cap) H Single Color LE with 1 Element Bicolor Red Amber Green Red/Green Maximum Forward Current I FM 25mA 30mA 25mA 30/25mA Typical Forward Current I F 20mA 20mA 20mA 20mA Forward Voltage V F 2.25V 2.1V 2.2V 2.0/2.2V Maximum Reverse Voltage V RM 5V 5V 5V Current Reduction Rate Above 25 C I F 0.33mA/ C 0.40mA/ C 0.33mA/ C 0.43/0.38mA/ C Ambient Temperature Range LE Specifications Bicolor LE with 2 Elements (+) (-) (+) (-) AT484 (4.0).157 (2.0).079 Material: Polycarbonate 1C 1 (19.0) ia (2.0).079 Cap for Nonilluminated AT4017 (19.0) ia 1F 25 ~ +70 C AT4030 CF Cap with Window Factory LE; Not Available Separately Cap No Lamp 53

9 Standard Size Snap-in Pushbuttons (-) (5.08) TYPICAL SWITCH IMENSIS (15.8) Sq.622 Single & ouble Pole LB15SKW01-12-CJ Single pole models do not have terminals 4, 5, & 6. Single & ouble Pole LB16CKW01-12-CJ Single pole models do not have terminals 4, 5, & 6. (17.8).701 (17.8) Sq.701 (19.0) ia (23.7) ia.933 (24.0).945 Single & ouble Pole LB26RGW01-12-CJ Single pole models do not have terminals 4, 5, & 6. (5.08) (1.0).039 (3.2).126 (1.8).071 (1.8).071 (1.0).039 (3.2).126 (1.8).071 (1.0).039 (3.2).126 (1.0) ia Typ.039 (21.5).846 Latchdown Position (21.5).846 Latchdown Position (22.5).886 Latchdown Position OPTIAL ACCESSORIES (0.5) (15.0) (4.0) (0.3) Typ.012 (1.2) x (2.0) Typ.047 x.079 (0.5) Typ (1.2) x (2.0) Typ.047 x.079 (0.5) Typ (1.2) x (2.0) Typ.047 x.079 (0.5) Typ (0.74) Typ L (-) L (-) 4 4 (2.8) Typ.110 (5.08) Typ (2.8) Typ.110 (5.08) Typ L (-) (5.08) Typ (22.0).866 PCB Adaptors AT711 Single Pole Straight PC Terminals AT712 ouble Pole Straight PC Terminals (0.5) (15.0) (4.0) (0.3) Typ.012 L (0.74) Typ.029 Note: Order adaptors separately. L (-) (5.08) (15.8) Sq (15.8) Sq.622 (15.8) Sq.622 (21.7) ia.854 (5.08) Typ (15.8).622 (2.8) Typ.110 (1.0) ia Typ

10 Standard Size Snap-in Pushbuttons Series LB AT497 End (20.0).787 End Position Material: Polyamide AT499 Opens 90 Closes manually Material: Polyamide AT4171 Opens 180 Closes automatically (16.2) Sq.638 AT4171 (20.5).807 (10.5).413 AT498 Center Center Position (4.3) Typ.169 (5.2).205 (15.0).591 (1.19).047 OPTIAL ACCESSORIES (23.5).925 (19.2).756 (1.19).047 (19.2).756 Barriers (21.0).827 (10.0).394 (17.0).669 Cutouts for More Than 1 Switch A =.752 (19.1mm) x Number of Switches (1.3mm) A =.996 (25.3mm) x Number of Switches (1.3mm) (20.0).787 s reduce depth of switch behind panel by (0.5mm). (39.0) Min* (20.4).803 (20.4).803 (N) (N) = Number of switches * Minimum dimension allows opening of cover to 180 Spring Loaded (20.5).807 (10.5).413 (18.4).724 (20.4).803 Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel A (8.0).315 Recommended Panel Thickness:.039 ~.106 (1.0mm ~ 2.7mm) (16.2).638 (14.2) (14.0) Sq.551 (17.9) Sq.705 (17.9).705 (7.1).280 (17.9)

11 Standard Size Snap-in Pushbuttons AT4057 Opens 90 Closes manually Material: Polyamide AT4172 (20.5).807 (16.2).638 AT4172 (10.5).413 (N) = Number of switches AT4002 (21.0) ia.827 (26.6) (7.3).287 (22.4).882 (2.5).098 (26.6) (N) * Minimum dimension allows opening of cover to 180 (21.8) ia.858 (30.0) ia OPTIAL ACCESSORIES s reduce depth of switch behind panel by (0.5mm). Spring Loaded (39.0) Min* AT4001 (20.5).807 (15.0) Sq.591 (10.5).413 (24.6).969 ust Covers (7.3).287 (26.6) Opens 180 Closes automatically Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel Recommended Panel Thickness:.039 ~.106 (1.0mm ~ 2.7mm) Materials: PVC with polyethylene gasket; PVC loses pliability below 0 C (32 F). ust Covers reduce depth of switch behind panel by (0.5mm). (26.0) (2.5).098 (10.0).394 (24.0) Sq.945 (8.0).315 AT4011 (16.5).650 (22.7).894 (24.15).951 (20.4) (30.2) (24.1).949 (14.0).551 (21.0).827 (7.1).280 (17.9).705 (16.5).650 (24.0)