Performance Selection Data
|
|
- Baldric Lambert
- 5 years ago
- Views:
Transcription
1 Series "NP" & "RG" AIRFLO Burners Page 5505 Performance Selection Data Operation in shaded area requires special considerations Optimum Design Area Operation in shaded area requires special considerations Optimum Design Area 9/03
2 Page 5506 Series "NP" & "RG" AIRFLO Burners Performance Selection Data (cont'd.) Optimum Design Area Airstream velocity across and through your burner's mixing plates must be kept uniform and within desired limits by use of a silhouette profile plate through which the burner fires. A 6" (minimum) profile plate should be installed surrounding the interior duct walls at the leading edge of your burners mixing plates. Optimum design ranges for the various burner types are shown in the above graphs. Velocities (SFPM) are measured with a velometer directly in the duct at the plane of the profile plate and leading edge of burner mixing plates. To determine profile opening areas, add burner displacement areas (Ft 2 /section) from Table 1 for your complete burner assembly to "Net Free Area" of your duct: "Net Free Area" of Duct (Ft 2 ) = Fan Volume (SCFM) Velocity (SFPM) Net Free Area (Ft 2 ) + Burner Displacement (Ft 2 ) = Profile Area (Ft 2 ) Various duct size/profile area relationships may give slightly different field site data than is shown in Table 2. Velocities should always be confirmed and established by use of a velometer on actual field site installation. Table 1: Velocity Factors Table 1: Burner Section Displacement 2 ( ft /section) Inlet Feed Limitations: NP-I NP-II NP-III RG-IV 1-1/4" end 4' 4' ' inlet flange KBtu/hr 1-1/2" back 5' 5' ' inlets* KBtu/hr *Note: For 36 back inlet sections, not more than 6" off any one leg Pilot Capacities: Nominally rated at 25,000 Btu/hr with natural gas differential pressures of 4-6" w.c. Desired velocity across burner at profile plate opening (SFPM) Appoximate velocity pressure reading at profile plate ("wc) NP RG 6" Straight " Straight " Straight " Straight " Back Inlet " Back Inlet " x 6" Tee " x 6" Elbow
3 Series "NP" AIRFLO Burners Page 5507 Approximate Envelope Dimensions (Nominal, in Inches) Burner Sections (All burners shown are available in NP-I, II or III versions. Use one of these numbers (I, II or III) in place of asterisk (*) in burner designation when ordering.) NP- * -6 6" Straight or 6"P Pilot NP- * -12 or NP- * -12B 12" Straight or 12B Back Inlet NP- * " Straight NP- * " Straight NP- * -L 6" X 6" Elbow NP- * -T 12" X 6" Tee NP- * -36B 36B Back Inlet Typical End View 4/95
4 Page 5508 Series "NP" AIRFLO Burners Pilots, End Closures, and End Inlet Flange Sets NOTE: All open ends of burner assembly must be closed off with one of these end closures or pilots. One-piece cast end closures should not be used if temperature rise exceeds 300 F. Plain End Closure Sets End Inlet & Pilot Flange Sets NP-EC (1 pc) End Closure Set Pilot End Plate Sets NP-EP (2 pc) End Plate Set NPF- 1-1/4" -FR-SI (1 pc) Pilot Set w/si NPF- 1-1/4"- EP (2 pc) End Inlet Flange Set NPF- 1-1/4"- FR-SI (2 pc) Pilot Set w/si NP-Pak Pilot Set w/si NP-Pak Pilot Set w/adj. Orifice/SI Common Dimensions (Nominal, in Inches) Typical End View NP-Pak Pilot Set w/orifice/cock/tube/ SI NP-EC-SI-3/4"UV (1 pc) Pilot Set w/ SI NP-EC-SI-1/2"-FR (1 pc) End Closure Set w/si Pilot Assembly Section NP-6P Pilot Section w/built-in Pilot includes end plate pilot w/si onto its own special 6" Series NP AIRFLO Burner assembly PIpe threads on this page conform to NPT (ANSI Standard B2.1) Legend: 1-1/8" test connection 2-1/4" pilot gas connection 3-14mm spark ignitor connection 4-1/2" or 3/4" UV/FR connection bushed to 1/4" for FR 5 - Alternate 1/4" angled FR location 6-1/8" pilot gas connection 7-1-1/4" NPT gas inlet
5 Series "RG" AIRFLO Burners Page 5509 Burner Sections Approximate Envelope Dimensions (Nominal, in Inches) RG-IV-6 6" Straight or 6"P Pilot RG-IV-12 or RG-IV-12B 12" Straight or 12B Back Inlet RG-IV-18 18" Straight RG-IV-24 24" Straight RG-IV-L 6" X 6" Elbow RG-IV-T 12" X 6" Tee RG-IV-36B 36B Back Inlet Typical End View 5/88
6 Page 5510 Series "RG" AIRFLO Burners Pilots, End Closures, and End Inlet Flange Sets NOTE: All "open" ends of burner assembly must be closed off with one of these end closures or pilots. One piece cast end closures should not be used if temperature rise exceeds 300ºF. Plain End Closure Sets End Inlet & Pilot Flange Sets RG-EP (2 pc) End Plate Set RGF- 1-1/4" -FR-SI (1 pc) Pilot Set w/si RGF- 1-1/4"- EP (2 pc) End Inlet Flange Set RGF- 1-1/4"- FR-SI (2 pc) Pilot Set w/si Pilot End Plate Sets Pilot Assembly Section RG-6P Pilot Section w/built-in Pilot includes end plate pilot w/si and a special 6" Series RG AIRFLO Burner assembly RG-Pak Pilot Set w/ RG-Pak Pilot Set w/ SI Adj. Orifice/SI RG-Pak Pilot Set w/orifice/cock/tube/si Common Dimensions (Nominal, in Inches) Typical End View Legend: 1-1/8" test connection 2-1/4" pilot gas connection 3-14mm spark ignitor connection 4-1/2" UV/FR conn. bushed to 1/4" for FR 5 - Alternate 1/4" angled FR location 6-1/8" pilot gas connection 7-1-1/4" NPT gas inlet Pipe threads on this page conform to NPT (ANSI Standard B2.1)
7 "NP" & "RG" AIRFLO Burners Page 5511 Accessories / Replacement Items Dimensions, Nominal in Inches 14mm Spark Ignitor Profile Plate Bracket Provides support for profile within closed burner loop. 1/4" dia. Flame Rod (1/4" NPT) Adjustable Orifice Support Bracket Division Plate Provides isolation of burner feed where desirable. Normally used in pairs as shown here. Mount to burner assembly at any joint. External Mounting Assembly Frequently used to provide easy accessibility to spark ignitor and flame supervision components. External Mounting Plate Used with typical pilot Opening Required Includes Mounting Plate with two (2) feed-through insulators for internal mounting of Spark Ignitor and Flame Rod. 5/88
8 Page 5512 Notes "NP" & "RG" AIRFLO Burners
Design and Application Details
LO-NOX Line Burners Page 5803 Design and Application Details Total heat release and LO-NOX Burner footage are normally selected from the tables given in the Series HG Mixing Tube section of the Maxon catalog
More informationPilot Capacities/Specifications
s Page 9505 Capacities/Specifications Maxon offers a wide range of gas pilots to meet the specific needs of each of its burner product lines. In most cases, the appropriate burner catalog section will
More informationAssembly Numbers. Approximate net ship weight (in pounds) shown in parentheses
Page 5700-A/P-1 Burner Sections Back Inlet Feed Sections (each requires inlet flange from Page 5700-A/P-2) C OMBUSTIFUME Line Burners Material Specifications > w/#310 SS mixing plates w/ Hastelloy X mixing
More informationCapacities and Operating Data
CROSSFIRE Line Burner Page 5603 Capacities and Operating Data Performance Data Lineal heat release at high fire Minimum lineal heat release Btu/hr/f t 1,000,000 1,250,000 1,500,000 1,750,000 2,000,000
More informationAssembly Numbers Style A, B & C LINOFLAME Burners
Premix-type Line Burners Page 00-A/P-1 Style A, B & C LINOFLAME Burners S tyle A, B & C LINOFLAME Burners with cast iron ignition rails L INOFLAME Burner Section Description straight section (Code) S tyle
More informationDesign and Application Details
Model 400 OVENPAK -II Gas Page 2153 Design and Application Details OVENPAK -II s are nozzle-mixing gas burners for many industrial direct-fired applications where clean combustion and high turndown are
More informationEclipse RatioAir Burners
Parameter Maximum Input, BTU/hr (kw) 1, Minimum Input, BTU/hr (kw) Lower inputs may be achieved. Contact factory. Main Gas Inlet Pressure, "w.c. (mbar) 3 Fuel pressure at ratio regulator inlet. High Fire
More informationAPX Nozzle-mix line burner
Duct urners - PX urners 1 E-i-03/16 PX Nozzle-mix line burner Nozzle-mixing line burner for use with low pressure natural gas, propane and butane Eliminates leakage with its single-piece, aluminum extrusion
More informationDesign and Application Details
Model 400 OVENPAK Gas Page 2105 Design and Application Details OVENPAK s are nozzle-mixing gas burners for many industrial direct-fired applications where clean combustion and high turndown are required.
More informationDesign and Application Details
Model 400 OVENPAK Gas Page 2153 Design and Application Details OVENPAK s are nozzle-mixing gas burners for many industrial direct-fired applications where clean combustion and high turndown are required.
More informationGAS BURNERS TYPE JR Forced Draft Burners 3450 RPM motor and squirrel cage blower Leakage test, pilot and main gas cocks Gas electric pilot and gas ign
3450 RPM Motor, squirrel cage blower, panel with 2 lights (power and main fuel) and control switch Gas electric pilot and gas ignition transformer Leakage test cock, pilot cock and main gas cock Pilot
More informationEclipse Vortometric Burners Series HI
Version Burner Model Parameter 6V 8V V V V 6V 8V V V 8V 3V 36V Max. Input MM BTU/hr (MW) (.8).5 (3.) 7 (5.0) 3 (6.7) 3 (9.) () (6.) 78 (3) 90 (6) 5 (37) (7) (6) Min. Input MM BTU/hr (MW) (Natural Gas)
More informationStart-up Instructions
RadMax Burners Page 400-S- Start-up Instructions Read complete instructions before proceeding and familiarize yourself with all the system s equipment and components. Verify that all equipment has been
More informationAPX Nozzle-mix line burner
Nozzle-mix line burner TECHNICL CTLOG Nozzle-mixing line burner for use with low pressure natural gas, propane and butane Eliminates leakage with its single-piece, aluminum extrusion body design Cooler
More informationField proven low emissions. State-of-the-art low NOx firing - adjustable for application flexibility
-.9- KINEDIZER LE High capacity low NOx gas burners Field proven low emissions. State-of-the-art low NOx firing - adjustable for application flexibility Lower NOx and less excess air than standard KINEDIZER
More informationLow Temperature Burners - STICKTITE and PILOTPAK Nozzles
Low Temperature Burners - STICKTITE and PILOTPK Nozzles STICKTITE & PILOTPK Flame retention nozzles -.- For open-port firing or open environment firing Provides positive flame retention and stable clean
More informationGEMINI GAS CONTROL PRODUCT INFORMATION
GEMINI GAS CONTROL PRODUCT INFORMATION The Gemini (6G) combination gas control valve is a versatile multifunction control designed to meet the requirements for use with non-piloted intermittent ignition
More informationKINEMAX. Medium velocity gas or oil burners
KINEMAX Medium velocity gas or oil burners High Temperature Burners - KINEMAX -.- Exit velocities up to 00 km/h (8 m/s) to promote workload heat penetration and better furnace temperature uniformity Operate
More informationSpecifications of STICKTITE and PILOTPAK Nozzles
Low Temperature urners - STICKTITE and PILOTPK Nozzles 1-1.1-5 Specifications of STICKTITE and PILOTPK Nozzles This graph indicates the relationship between capacity and applied mixture differential pressure
More informationAPX Nozzle-mix line burner
Nozzle-mix line burner TECHNICL CTLOG Nozzle-mixing line burner for use with low pressure natural gas, propane and butane Eliminates leakage with its single-piece, aluminum extrusion body design Cooler
More informationECLIPSE AIR HEAT BURNERS Series AH, DAH, TAH & CAH
Info 140 11/4/03 ECLIPSE AIR HEAT BURNERS Series AH, DAH, TAH & CAH U.S. Reissue Pat. No. 26,244 Canadian Pat. No. 743,782 AH, Front View Data 140-1 AH, Back View Data 140-1 TAH Data 140-3 DAH, Blower
More informationSpecifications of STICKTITE and PILOTPAK Nozzles
-.-5 Specifications of STICKTITE and PILOTPK Nozzles This graph indicates the relationship between capacity and applied mixture differential pressure for STICKTITE and PILOTPK nozzles when fed with an
More informationFLOW TEK VALVES & CONTROL S INC
FLOW TEK VALVES & CONTROL S INC e-mail:- info@flowagevalves.com PLOT NO-172,173, ROAD NO-4, KATHWADA, G.I.D.C. AHMEDABAD. PHONE NO:- 079-22900219,22900220, MOBILE:-09824539702, 9824080899. an ISO 9001
More informationData /1/07 Eclipse RatioAir Burners Model RA0040
Maximum input, () at neutral chamber conditions 60Hz Packaged Maximum input, () at neutral chamber conditions 50Hz Packaged Minimum input, () Lower inputs may be achieved. Contact factory. Main Gas Inlet
More informationRatioAir Burners. Model RA0750. Data /31/05. Main Specifications - RA0750
Main Specifications - RA0750 PARAMETER Maximum input, Btu/hr (kw) at neutral chamber conditions. (Natural Gas) 60Hz Packaged 50Hz Packaged Minimum input, Btu/hr (kw) Lower inputs may be achieved. Contact
More informationData 330-3 9/15/07 Eclipse ImmersoJet Burners Model 3 IJ Version 2 Main Specifications PARAMETER BLOWER SIZE Blower Type 6" w.c. Packaged (60Hz) 10" w.c. Packaged (60Hz) Remote Blower Maximum Input (Btu/hr)
More informationRatioAir Burners. Model RA1000. Data /31/05. Main Specifications - RA1000
Main Specifications - RA1000 PARAMETER Maximum input, Btu/hr (kw) at neutral chamber conditions. (Natural Gas) 60Hz Packaged Blower 50Hz Packaged Blower Minimum input, Btu/hr (kw) Lower inputs may be achieved.
More informationEclipse RatioAir Burners
Data 115-1 10/1/07 Eclipse RatioAir Burners Main Specifications - RA0 PARAMETER Maximum input, () at neutral chamber conditions 60Hz Packaged Maximum input, () at neutral chamber conditions 50Hz Packaged
More informationSpecifications of OPTIMA SLS Burners
1.1.9-4 Low emperature urners - PIM L pecifications of PIM L urners ypical burner data Fuel: natural gas at 60 F with 1000 tu/ft 3 (st) HH - sg = 0.6 (1) ombustion air: 60 F - 21% 2-50% humidity - sg =
More informationEasily removable slide-out blower design PSC multi-speed permanently lubricated blower motor for low maintenance and optimum efficiency
Gas Furnaces PRODUCT SPECIFICATIONS INSTALLATION OPTIONS A vailable in Upflow/Horizontal and Counterflow models 80% AFUE 44,000 to 32,000 Btuh Input.5 to 5 Tons Add-On Cooling HEAT EXCHANGER A luminized
More informationVALUPAK. Packaged gas burners
VALUPAK Packaged gas burners 1-1.5-1 E - i - 11/14 High turndown. Available in 6 sizes. Capacities: 0.007 MBtu/hr - 4 MBtu/hr. Stable and clean combustion. Suitable for UV scanner and flame rod. Natural
More informationM/MR Modulating Valves TABLE OF CONTENTS DESCRIPTION SPECIFICATIONS. For Atmospheric, Infrared, and Direct Fired Burners
M/MR Modulating Valves design certified For Atmospheric, Infrared, and Direct Fired urners TALE OF CONTENTS Description/Specifications... 1 Introduction... 2 Direct Fired Applications (Negative Pressure)...
More informationPREMIX TUNNEL BURNERS
FOR ENCLOSED GASAIR COMBUSTION MODEL: 01, 0, 06 Revision: 0 BULLETIN 01, 0, 06 EXPLODED VIEW Pyronic Tunnel Burners will burn any standard fuel gas at mixture pressures ranging from 0.1 to 60 W. C. Exclusive,
More informationNorth American Combustion Burners
Combustion North American Combustion Burners 4441 North American Tempest High Velocity Gas Burner Jet action burner offering superior recirculation Slotted tile produces exceptional temperature uniformity
More informationDEXEN INDUSTRIES Inc. GENERAL CATALOG. DEXEN INDUSTRIES Inc.
DEXEN INDUSTRIES Inc. GENERAL CATALOG DEXEN INDUSTRIES Inc. 6003 GAS VALVES 6003-series gas valve is an effective and reliable gas valve for low-btu gas product and application. The product is most commonly
More informationTORCH BURNERS LOW, MEDIUM, AND HI-PRESSURE SERIES DESCRIPTION LOW-PRESSURE SERIES MODEL : T,TA,TB,RTA,RTB ET,ETA,ETB,RETA,RETB 12 ET 12 RETB
TORCH BURNERS LOW, MEDIUM, AND HIPRESSURE SERIES MODEL : T,TA,TB,RTA,RTB ET,ETA,ETB,RETA,RETB Revision: 0 BULLETIN 325, 32, 327 2 ET 2 RETB DESCRIPTION Torches are made up in three series LowPressure,
More informationLVDT/HC PILOT BURNER. External raw gas pilot burner
4-22.4-1 LVDT/HC PILOT URNER External raw gas pilot burner Stable pilot flame in combination with MXON IRFLO LV, HC, DELT-TE and COMUSTIFUME burners Rugged design urns natural gas, propane and LPG Suitable
More informationNorth American Combustion Burners
Combustion North American Combustion Burners 4441 North American Tempest High Velocity Gas Burner Jet action burner offering superior recirculation Slotted tile produces exceptional temperature uniformity
More informationTriOx Triple Air Staged Ultra Low NOx Burner
Triple Air Staged Ultra Low NOx Burner TriOx-1 Edition 09-08 Ultra low NOx emissions of 20 ppm or less Invisiflame mode offers positive UV flame supervision throughout entire operating range for excellent
More informationNorth American 4575 HiRAM
Combustion North American 4575 HiRAM The quality and performance of our Tempest, but bigger. Low NOx burner High Velocity - High Turndown Inputs to 4-25 million Btu/hr Direct Spark or Pilot Lighting Furnace
More informationDELUGE VALVE MODEL: SD-DVA TECHNICAL DATA : VALVE OPERATION TRIM DESCRIPTION DESCRIPTION PRESSURE THREADED OPENING
DELUGE VALVE MODEL: SD-DVA TECHNICAL DATA : NOMINAL SIZE MATERIAL MAXIMUM SERVICE PRESSURE 200, 150, 100, 80 & 50NB Cast Iron 12 Bar (175 PSI) THREADED OPENING MOUNTING FACTORY HYDROSTATIC TEST PRESSURE
More informationSelf-Operating Temperature Regulators
Self-Operating Temperature Regulators Remote Bulb for Heating, Cooling, Mixing and By-Pass Applications Powers # Regulators With Powers # Self-Operating Temperature Regulators, you no longer need external
More informationLVG SERIES. Gas Limiting Orifice Valve. Features. Benefits. Combustion Excellence Since 1888 LVG-1
Gas Limiting Orifice Valve Features Precision machined valve flow piston Rugged cast iron body Replaceable cartridge assembly for LVG 55-5 Straight through valve design; right angle valve option Pressure
More informationCGi Series 2 Section Assembly
CGi Series 2 Section Assembly 8 0 2 9 9 Current Service Parts CGi Series 2 Section Assembly Part Description Mfr. Mfr. s Part -0-80 End section, left hand, cast #2 Weil-McLain 2-0-82 End section, right
More informationNorth American 4485 Tempest SE
Combustion North American 4485 Tempest SE Medium/High Velocity Gas Burner Low NOx gas burner, durable construction and flexible desgin to fit a variety of applications. NPT or BSP air/gas inlets, adjustable
More information2.0 Burner Operating Parameters and Requirements
ECLIPSE INFORMATION GUIDE Silicon Carbide Radiant Auto-Recupes Info 322 2/99 WARNING Handle silicon carbide tubes carefully. Do not drop them or hammer on them. Although they feature excellent mechanical
More informationF300 Pressure Regulator
F300 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P302 has Internal Relief Valve for Overpressure Protection Ideal for Fix Factor Billing The F300 series pilot operated
More informationINFINITE ENERGY 2-199
3" AIR 3" FLUE RSUB-191 1 1/2" NPT 1" NPT 1 1/2" NPT FRONT VIEW Fuel Type Natural/Propane Gas Boiler FLA.92* Input BTU/hr. 200,000 / 59 kw Min. Gas Pressure Required 3" W.C.** Output BTU/hr. 183,600 /
More information1470 SERIES HOT AIR GAS BURNER
1 SERIES HOT AIR GAS BURNER CAPABILITIES High or low temperature furnace High excess air 800% or more Ratio or tempered flame operation Nominal capacity range 0,000 to 3.5 MM Btu/hour Suitable for light
More informationInfo 110 4/98. RatioMatic Burners. RM Series version through 600 Sizes. 750 through 2000 Sizes
Info 110 4/98 RatioMatic Burners RM Series version 1.01 50 through 600 Sizes 750 through 2000 Sizes For Ratiomatic Serial Numbers 95-5500 and Above Version 1.01 7/97 Contents 1.0 Operating Parameters &
More informationReplacement Parts List. Knight Fire Tube Boilers KHB 055 thru 285 Series 100 & _ _Rev B
Replacement Parts List PARTS & SERVICE DEPARTMENT Nashville, Tennessee 877-554-5544 Fax: 615-882-2918 parts_team@lochinvar.com www.lochinvar.com Knight Fire Tube Boilers KHB 055 thru 285 Series 100 & 101
More informationSpecifications of LVDT/HC-pilot burner. Materials of construction. Duct burners - LVDT/HC-pilot burner. combustion systems for industry
4-22.4-4 Specifications of LVDT/HC-pilot burner Typical burner data 15 C 21 % O 2 combustion air 50 % humidity natural gas with 10.9 kwh/m³(st) HHV - sg = 0.6 [1] Stated pressures are indicative - actual
More informationBULLETIN 456. July 1997 VANEAXIAL FANS. Type W Direct Drive/Belt Driven. Model VW Direct Drive. Model VWBD Belt Driven
BULLETIN 456 July 1997 VANEAXIAL FANS Type W Direct Drive/Belt Driven Model VW Direct Drive Model VWBD Belt Driven Aerovent certifies that the Type W Vaneaxial Fans shown herein are licensed to bear the
More informationF200 Pilot Operated Pressure Regulator
F200 Pilot Operated Pressure Regulator External or Internal Pressure Registration Minimize Sudden Downstream Load Change Ideal for Fix Factor Billing Quick Response Time / High ccuracy The F200 series
More informationForged Fittings. High Technology Valve & Fitting Series
Forged Fittings High Technology Valve & Fitting Series Forged steel socket Welding fittings 6 ~ 13 Forged steel threaded fittings 14 ~ 20 Forged steel outlet fittings 21 ~ 23 Standard threads specifications
More informationJANDY HEATERS A QUICK REFERENCE OF MOST COMMONLY REPLACED PARTS
JANDY HEATERS Heaters H-58 A QUICK REFERENCE OF MOST COMMONLY REPLACED PARTS E-Z FIND CHART MARK V XE XE SERIES I SERIES I MILLIVOLT MILLIVOLT ELECTRONIC MILLIVOLT ELECTRONIC DM, DR EG ES, EC EPG EPS,
More informationPT-M90 Automatic Full-Sequence Modulation Gas Control System
PT-M90 PT-M90 Automatic Full-Sequence Modulation Gas Control System PT-M90 Module System Illustration Pucada.Tech M901-0316 Gas Valve (PT-V1C-with step motor) A Profile Dimension: Length(84mm) * Width(40mm)
More informationF200 Pilot Operated Pressure Regulator
F00 Pilot Operated Pressure Regulator External or Internal Pressure Registration Minimize Sudden ownstream Load Change Ideal for Fix Factor Billing Quick Response Time / High ccuracy The F00 series is
More informationBurner Selection Criteria
UNI-RAD Radiant Tube Burners Page 4803 Burner Selection Criteria Combustion Air View Port/Optic Flame Sensor Mount Gas Inlet 3"- 4" Burner Selection The UNI-RAD Burner can be used with various radiant
More informationMULTIFIRE. High temperature dual fuel burner
MULTIFIRE High temperature dual fuel burner High temperature burners - MULTIFIRE 3-11.3-1 Operates on-ratio or with excess air to meet the specific demands of your combustion process needs Burns most clean,
More informationIHR Series With Standard Oven ITEM NO DESCRIPTION PART # 36" 1 Top Grate Cast Iron 12" X 28" - (Old Style) 1187 N/A *** 12" Top Grate 12 x 13 1/4
1 Top Grate Cast Iron 12" X 28" - (Old Style) 1187 N/A *** 12" Top Grate 12 x 13 1/4 (Front) Open Burner 35334 3 *** 12" Top Grate 12 x 13 1/4 (Rear) Open Burner 35335 3 2 Top Grate Cast Iron 18" X 28"
More informationVALUPAK. Packaged gas burners
VALUPAK Packaged gas burners Low Temperature Burners - VALUPAK 1-1.5-1 High turndown. Available in 6 sizes. Capacities: 2 kw -1124 kw (HHV). Stable and clean combustion. Suitable for UV scanner and flame
More informationTechnical Information
Date of last update: 09-07 Ref: D7.19.1/0806-0907/E Application Engineering Europe ASSEMBLING THE DISCHARGE TEMPERATURE CONTROL VALVE FOR SEMI-HERMETIC R22 LOW TEMPERATURE APPLICATIONS 1 The Discharge
More informationGUH 95 Series TECHNICAL SPECIFICATIONS. FEATURES and BENEFITS
TECHNICAL SPECIFICATIONS GUH 95 Series Two Stage, Variable Speed, Condensing Upflow/Horizontal and Downflow Gas Furnaces Induced Draft - 95.1 AFUE Input 60,000-120,000 Btuh The high efficiency upflow gas
More informationQ SERIES II GAS-FIRED DIRECT VENT CONDENSING HOT WATER BOILER
Models Q90-25 Q90-50 Q90-5 Q90-200 Q90 25-200 SERIES II GAS-FIRED DIRECT VENT CONDENSING HOT WATER BOILER REPAIR PARTS, OPTIONAL KITS Ordering Instructions Order Parts through your nearest supplier. When
More informationULTRA HIGH EFFICIENCY MODELS WITH DIRECT SPARK IGNITION
RESIDENTIAL AND COMMERCIAL GAS REPLACEMENT PARTS LIST ULTRA HIGH EFFICIENCY MODELS WITH DIRECT SPARK IGNITION EFR160T120*(EN,SX) EF(60,100)T(125-300)(E*N)(*X)(A)2 (Serial Number GB13006174 and AFTER) Includes
More informationGAS FURNACES II 80.0% 81.4% A.F.U.E. UPFLOW/ HORIZONTAL GAS FURNACES SILHOUETTE
FORM NO. G22-448 REV. 10 Supersedes Form No. G22-448 Rev. 9 GAS FURNACES UGPH- SERIES Models with Input Rates from 50,000 to 150,000 BTU/HR [15 to 44 kw] (U.S. & Canadian Models) Annual Fuel Utilization
More informationDirect Gas-Fired Make-up Air Heaters
Direct Gas-Fired Make-up Air Heaters SDM-E SERIES OUTDOOR SPECIFICATIONS MANUAL MANUFACTURED BY : BROTHERS LIMITED TABLE OF CONTENTS Summary description of the unit...4 Required burner capacity...6 Dimensions
More informationDELUGE VALVE DATA SHEET
FIRE FIGHTING EQUIPMENT DATA SHEET DELUGE VALVE DATA SHEET JOB NO. : RFQ. NO. : ISSUE : SHEET OF 01 CUSTOMER : ITEM NO. : 02 PROJECT : QUANTITY : 03 LOCATION : SERVICE : FIRE WATER AND / OR FOAM SYSTEM
More informationGAS-FIRED DIRECT VENT CONDENSING HOT WATER BOILER ( MBH) REPAIR PARTS MANUAL. P/N , Rev. 1.2 [02/06]
GAS-FIRED DIRECT VENT CONDENSING HOT WATER BOILER (25-200 MBH) REPAIR PARTS MANUAL P/N 24000523, Rev..2 [02/06] TABLE OF CONTENTS I. Circulator Pumps (Optional)...2 II. Burner Assembly...3 III. Boiler
More informationMP GS/GD. Toll Free Phone, (US & Canada): (800) Toll Free Fax, (US & Canada): (800)
MP GS/GD Toll Free Phone, (US & Canada): (800) 427-6668 Toll Free Fax, (US & Canada): (800) 36-7745 http://www.garland-group.com Page 2 Moisture + MP-GS/GD DESCRIPTION PAGE Deluxe Control Panel 4 Standard
More informationSUMG-100. Burner Package & Components
Burner Package & Components Burner Package & Components U_GO_PL_CONVECTION_SUMG100_1.pdf Burner Package & Components 1A 4521462 Burner Pack - DSI MCO - 60K - Natural Gas 1 [1] 1A CK4521468 Burner Pack
More informationMASTER DIRECT OIL HEATERS. MODEL 35 CED 10 kw Model ILLUSTRATED PARTS BREAKDOWN. Motor and Pump Assembly
MODEL 35 CED 10 kw Model ILLUSTRATED PARTS BREAKDOWN 3 1 2 4 5 11-5 11-1 11-2 6 7 8 11 15 11-4 23 13 41 16 17 11-3 18 1 24 20 33 34 27 3 43 25 31 37 2 30 28 26 42 35 12 32 18-1 18-2 18-18 36 18-4 18-5
More informationGV30 / GV30A SERIES GAS COMBINATION CONTROL SYSTEMS FOR COMMERCIAL COOKING APPLIANCES.
GV0 / GV0A SERIES GAS COMBINATION CONTROL SYSTEMS FOR COMMERCIAL COOKING APPLIANCES R www.mertikmaxitrol.com CONTENT GENERAL INFORMATION GV0 AND GV0A STANDARD FEATURES OPTIONAL TEMPERATURE KNOBS AND D-STEMS
More informationIntroduction to Johnson Controls Dampers
Damper and Actuator Product Guide 268.1 Damper Engineering Section Product Bulletin Issue Date 1297 Introduction to Johnson Controls Dampers For over 100 years, Johnson Controls has been the industry leader
More informationFlowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body
Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body VF 599-1 Description Features Application The Flowrite VF 599 series two-way valves are designed to work with either a pneumatic
More informationSpecifications of MAXON VALUPAK burners for 50 Hz operation
1-1.5-7 Specifications of MAXON VALUPAK burners for 50 Hz operation Capacity data in kw Gross heating value = 10.9 kwh/m 3 (st), d = 0.6. All figures are for balanced - 0 mbar - duct pressure VALUPAK size
More informationHigh Pressure 2-way 2 1/2-6 Globe Valves
Overview Datasheet High Pressure 2-way 2 1/2-6 Globe Valves Designed to work with either an electronic actuator with a 3/4-inch (20 mm) or 1-1/2-inch (40 mm) stroke, the two-way globe valves are available
More informationZEPHAIRE G MECHANICAL & SOLID STATE CONTROLS GAS CONVECTION OVENS REPLACEMENT PARTS LIST
ZEPHAIRE G MECHANICAL & SOLID STATE CONTROLS GAS CONVECTION OVENS REPLACEMENT PARTS LIST EFFECTIVE JULY 19, 2005 BLODGETT OVEN COMPANY, 44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: (802)
More informationA.O. SMITH WATER PRODUCTS CO., INC W. 115TH STREET ALSIP, ILLINOIS Phone: Fax: Website:
PSD-3-152/a WIRING/HARNESS & PROBES See page 8 PROPANE GAS TRAIN ASSEMBLY See page 6 COMMERCIAL POWER BURNER BOILER REPLACEMENT PARTS LIST COPPER BOILERS FOR HYDRONIC HEATING & HOT WATER SUPPLY LEGEND
More informationUltra High Efficiency Models With Direct Spark Ignition
RESIDENTIAL AND COMMERCIAL REPLACEMENT PARTS LIST Ultra High Efficiency Models With Direct Spark Ignition EFR160T120*(EN,SX) EF(60,100)T(125-300)(E*N)(*X)(A)2 (Serial Number GB13006174 and AFTER) Includes
More informationACL HIGH EFFICIENCY BURNER ASSEMBLY PATENTED BURNER WARNING
HIGH EFFICIENCY BURNER ASSEMBLY HIGH EFFICIENCY BURNER ASSEMBLY PATENTED BURNER WARNING This manual must be read in its entirety before installation of this burner. Installation must be performed by a
More informationFlowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body
Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body VF 599-1 VF114R1 VF115R1 Description Features Application The Flowrite VF 599 series two-way valves are designed to work with either
More informationTurbo Pressure Blowers
www.americanfan.com Bulletin VP4 Turbo Pressure Blowers Howden Industrial Fan Group American Fan / Joy Fan / Garden City Fan Features Heavy gauge continuously welded housings, reversible and rotatable
More informationBBG Gas Beta Burner. Designed for low pressure air operation. Rugged heavy gauge steel construction
BBG Gas Beta Burner BBG-1 Edition 02-08 BBG shown with pilot ignition and converging tile options. Designed for low pressure air operation Rugged heavy gauge steel construction Alloy or refractory tile
More informationToll Free Phone, (US & Canada): (800) Toll Free Fax, (US & Canada): (800)
Toll Free Phone, (US & Canada): (800) 427-6668 Toll Free Fax, (US & Canada): (800) 361-7745 http://www.garland-group.com MODEL: MCO-GS/GD-10 MU - CE UNITS Oven Manufactured Up To May 29, 2008 DESCRIPTION
More information1466 SERIES COLD AIR GAS/OIL BURNER
CAPABILITIES High or low temperature furnace High excess air 800% or more Ratio or tempered flame operation Nominal capacity range 0,000 to 3.5 MM Btu/hour Suitable for light wall construction FEATURES
More information36H Gas Control Product Information
Single Stage 36H Two Stage 36H 36H Gas Control Product Information The 36H combination gas control valve is a versatile multifunction control designed to meet the requirements for use with intermittent
More informationVENTING & COMBUSTION AIR GUIDE
PRE-INSTALLATION APPLICATION GUIDE VENTING & COMBUSTION AIR GUIDE Natural Gas, Propane and Dual Fuel Modulating and Condensing BOILER BODY VENT STARTER SECTION APPLIES TO MODELS: BMK 750 BMK 1000 BMK 1500
More informationINDUSTRIAL MICRODIFFUSION DUAL-FUEL BURNERS
Operations and Maintenance Manual for INDUSTRIAL MICRODIFFUSION DUAL-FUEL BURNERS Models MD-25-OG MD-7500-OG December 2012 Copyright 2012 Periflame, Design Guide 113 Industrial Dual-Fuel Burners, 12/01/2012
More informationG196 Series BASOTROL Redundant Combination Gas Valve with Manual Shutoff Valve
Product Bulletin Issue Date March 13, 2013 G196 Series BASOTROL Redundant Combination Gas Valve with Manual Shutoff Valve The G196 Series valves use the reliable valve body and magnetic operators from
More informationFlowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body
Flowrite VF 599 Series Two-Way Valves 2-1/2 to 6-inch Flanged Iron Body VF 599-1 Description Features Application The Flowrite VF 599 series two-way valves are designed to work with either a pneumatic
More informationKINEMAX MEDIUM VELOCITY GAS OR OIL BURNERS PRODUCT DESCRIPTION TECHNICAL CATALOG
KINEMAX MEDIUM VELOCITY GAS OR OIL BURNERS TECHNICAL CATALOG PRODUCT DESCRIPTION The KINEMAX burner is a nozzle-mixing, medium velocity burner. It provides a stream of hot combustion gases that promote
More information15B SERIES II. Models 15B045FE 15B070FE 15B096FE 15B120FE 15B145FE 15B170FE 15B195FE 15B245FE 15B295FE
Models B0FE B00FE B0FE B0FE BFE B0FE BFE BFE BFE B SERIES II Cast Iron Gas Fired Boilers For Forced Hot Water REPAIR AND REPLACEMENT PARTS Ordering Instructions Order Parts through your nearest supplier.
More informationWafer Silent Check Valves
Applications Liquid Service Metals & Mining Process Industry Water & Waste Water Power Industry Pulp & Paper Chemical Industry Oil & Gas Wafer Silent Check Valves Pressures to 740 PSIG Temperatures to
More informationType 459. Type 459. Available designs. Cap H2. with bushing 19. Lock nut. Bonnet. Outlet flange 2.4 Outlet adaptor 2.1. spacer.
Available designs 40 Cap H2 18 Adjusting screw with bushing 19 Lock nut 9 Bonnet 16 Spring plate 54 Spring 12 Spindle 17 Spring plate 14 Split ring 60 Gasket 8 Guide 57 Pin 61 Ball 7 Disc 2 Outlet body
More information1630 SERIES CYCLOPS TM ULTRA 4 LOW NOX TM HOT AIR BAFFLE BURNER
CAPABILITIES Industry leading low NOx emissions High momentum. luminous flames at all furnace temperatures High release rates with moderate main combustion air pressure Good turndown with flame characteristics
More informationIR 2000 Series Medium Duty Range w/standard Oven ITEM NO DESCRIPTION PART # 24" 36" 48" 60" 72" Griddle Plate Assembly 24"
1 Griddle Plate Assembly 12" 20006 1 1 1 1 1 Griddle Plate Assembly 24" 20007 1 1 1 1 1 Griddle Plate Assembly 36" 20008 1 1 1 1 Griddle Plate Assembly 48" 20009 1 1 1 Griddle Plate Assembly 60" 20010
More informationPARTS MANUAL FOR HEAVY DUTY GAS BROILERS
PARTS MANUAL FOR HEAVY DUTY GAS BROILERS CERAMIC MODELS Model HCB00 HCB HMCB HCB1 HCB SUNGLOW MODELS Model IR1 IR IR MODEL GHCBO0 SHOWN FORM 0907 (10-9) VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY
More informationVibration Isolators (6) Galvanized Wheel. Sealed Ball Bearing. Standard Duct Size Inlet Ring
The Lau FGP Series Blower is perfect for use in ventilating, exhausting, air conditioning, processing and general industrial applications. Cold Rolled Steel: all welded construction with painted enamel
More information