BELT Rapid Fold up Door

Transcription

1 BELT Rapid Fold up Door Quick Assembling Guidebook Belt Manualopen Basic Safety Edge /indupart /indupart /indupart /company/indupart-ltd

2 Table of Contents Table of contents Page 2 Unpacking Page 3 Exploded view A Page 4 Exploded view B Page 5 Column preassembling and door lifting Page 6 General wirings Page 7 Wiring between control board and terminal board A Page 8 Power supply Page 9 Terminal board on the motor Page 10 Motor safety switch,emergency and opening push buttons Page 11 Curtain assembling part A Page 12 Curtain assembling part B Page 13 Curtain assembling part C Page 14 Limit switch part A Page 15 Limit switch part B Page 16 Limit switch part C Page 17 Safety photocells Page 18 Safety edge Page 19 Flashing light Page 20 Control card Page 21 LED Page 22 Settings Page sales@indupart.co.uk

3 UNPACKING Unpacking 1. Canopy 2. Curtain 3. Columns 4. Motor and motor cover The door BELT is packed in a crate. The crate separately contains : n.2 columns,the wound curtain,the canopy and n.1 cardboard box with the control board and accessories. The canopy unit is composed of the canopy itself,the drive unit,the motor cover. If there is a counterweight,one of the two columns is double : the column itself and the cover sheltering the counterweight running sales@indupart.co.uk 3

4 Exploded EXPLODED View VIEW A 5. Roller 6. Bearing 7. Drive unit bracket 8. Gearbox 9. Gearwheels : limit switch pinions 10. Limit switch chain 11. Limit switch unit bracket 12. Limit switch unit 13. Motor 14. Shaft key 15. Side head plate 16. Fixing plate for belt 17. Lifting belt sales@indupart.co.uk

5 Exploded EXPLODED View VIEW B 6. Bearing 15. Side head plate (opposite motor side) 18. Canopy side cover sales@indupart.co.uk 5

6 Column Preassembling and Door Lifting 1. The upper and lower column base plates are bolted on the same side when delivered. 2. Unbolt one of the two column base plate and put it on the column opposite side. 3. Bolt it on the column opposite side. Put first columns and fix them. Lift and put the canopy and fix it. Check if columns are vertical and the canopy is horizontal by means of a bubble level. Check the two diagonals : they must be equal. Page sales@indupart.co.uk

7 DESCRIPTION TYPE OF CABLE CONNECTIONS G Cable for the power supply to the motor and the brake F Cable for controls and safeties 4 x 1,5 + 2 x 0,5 mm To the control board 12 x 0.5 mm To the control board H Cables for controls Minimum 0,5 mm To controls (options) D Cable for limit switches 3 x 0,5 mm To limit switch unit B Cable for safety photocell (Receiver) C Cable for safety photocell (Transmitter) E Cable for motor safety switch 4 x 0,5 mm To the photocell receiver on motor side 2 x 0,5 mm To the photocell transmitter on the opposite motor side To the motor safety switch General Wiring sales@indupart.co.uk 7

8 Wiring between control board and terminal board A. Cable pulling device. B. Photocell cable (Receiver ). C. Photocell cable (Transmitter TX). D. Limit switch cable. F. Cable for services. G. Motor power supply cable. H. Cables for eventual additional controls such radars and pull cords. E. Motor safety switch cable 1. Limit switches unit. 2. Terminal box on the motor. 3.Threephase motor. 4. Motor safety switch. 5. Motor side column. 6.Opposite motor side column. 7. Gear box sales@indupart.co.uk

9 The power supply is 400 V threephases. The cable to the control board must have the right section. There must be upline a suitable disconnecting switch. Power Supply sales@indupart.co.uk 9

10 Rectifier G1 YELLOW/GREEN G2 RED (From the control board) then WHITE (Just before the rectifier) G3 RED (From the control board) then WHITE (Just before the rectifier) G4 LIGHT BLUE G5 BLACK G6 BROWN M1 RED M2 WHITE M3 BLACK (or BROWN) m1 RED m2 WHITE m3 BLACK (or BROWN) MF1 BLUE MF2 BROWN The CC power supply for the brake is supplied through the rectifier. Terminal box on the motor

11 F7 TWO COLOURED BLUE/RED F8 TWO COLOURED PINK/GREY Connection in series among all NC contacts of the motor safety switch,the main and eventual additional emergency push buttons. Connection in parallel among all NO contacts of the main and eventual additional opening push buttons. Motor Safety Switch, Emergency and Opening Push Buttons

12 BELTS ON THE MOTOR SIDE BELTS ON THE SIDE OPPOSITE TO THE MOTOR WARNING! Before putting the wound curtain between columns,check carefully the position of belts (see above). CURTAIN ASSEMBLING PART A Curtain Assembling Part A sales@indupart.co.uk

13 BELTS ON THE MOTOR SIDE BELTS ON THE SIDE OPPOSITE TO THE MOTOR 1. Steel plate to hang the curtain by means of upper long bolts. Upper long bolts are placed along the upper stiffener. 2. Upper belt fixing plate on the roller. BELTS ON THE MOTOR SIDE 3. Upper belt fixing plate on the roller. BELTS ON THE SIDE OPPOSITE TO THE MOTOR Curtain Assembling Part B sales@indupart.co.uk 13

14 1. Check the belt fixing on the roller (see the previous page). 2. Move the curtain up and down using contactors T1 or T2. 3.Lift the curtain up. 4. Check the belt winding. Belts must wind on the roller as shown in the right part of the below shown figure. 5. By using long bolts put on the upper stiffener hang the curtain under the appropriate steel plates fixed to the canopy. 6. Close the door. 7. Adjust limit switches Roller 2. Curtain hanging long bolts 3. Curtain 4. Belt 5. Upper stiffener 6. Other stiffeners 6 Curtain Assembling Part C sales@indupart.co.uk

15 D1 YELLOW D2a GREEN (OPEN DOOR) D2 BROWN (CLOSED DOOR) D4 WHITE (PHOTOCELL SWITCHING OFF) F3 YELLOW F4 RED F5 GREEN F6 BROWN B3 YELLOW B4 RED Limit Switch Part A sales@indupart.co.uk 15

16 D2a D2 C1 OPEN DOOR CAM C2 PHOTOCELL SWITCHING OFF CAM C3 CLOSED DOOR CAM 1. Check the cam rotation acting on contactors T1 or T Acting on contactors close the door and adjust the cam C3 (brown cable) 1 2 C3 3.Acting on contactors open the door up to 10 cm above the safety photocell position and adjust the cam C2 (white cable) 1 2 C2 Limit Switch Part B sales@indupart.co.uk

17 4.Open the door up to the clear opening height and adjust the cam C1 (green cable) 1 2 C1 CABLE COLOUR LIMIT SWITCH ADJUSTMENT GREEN CABLE Open door limit switch When the door is open at the clear opening height WHITE CABLE Safety photocell switching off limit switch 100 mm over the safety photocell position BROWN CABLE Closed door limit switch When the door is closed Limit Switch Part C sales@indupart.co.uk 17

18 There are two predrilled holes one per column- in the lower part of the column. Insert the cable through the predrilled hole and fix the photocell. Safety Photocells C1 BLUE C3 BLACK B1 BLUE B2 BLACK B3 YELLOW B4 RED F1 BLUE F2 BLACK F3 YELLOW F4 RED D1 YELLOW D4 WHITE

19 Receiver Transmitter Transmitter Control Transmitter Transmitter Transmitter The safety edge transmitter is already connected to the resistive pressure sensitive strip. The receiver can be installed inside or outside of the control board box. The receiver must be connected to the control cad as above shown by the table by means of a cable 4 x 0.5 mm. Both receiver and transmitter are set before delivery. In case of an eventual set,push the button PROG on the receiver till one beep sounds and LED B1 lights on. Within 5 seconds push the button PROG on the transmitter. Within 8 seconds two beeps on the receiver sounds. Then the LED B1 switches off and the LED B2 switches on. Safety Edge sales@indupart.co.uk 19

20 DIP 7 ON FLASHING LIGHT DIP 7 OFF CONTINUOUS LIGHT Flashing Light sales@indupart.co.uk

21 LED LED 1 0 V AC V AC Power supply to brake V AC Power supply 4 Opening contactor 5 Closing contactor 6 Common contactor 10 Flashing light 230 V AC max 100 W 11 Flashing light 230 V AC max 100 W Blue V AC Power supply output Black V AC Power supply output Yellow 16 Common Red 17 Safety photocell Two coloured pink/grey 18 Stop input 19 Safety edge contact 20 Pedestrian opening input 21 Opening control input (push buttons,remote controls) 22,23,24 Common Green 26 FCA1 Open door limit switch Brown 27 FCC1 Closed door limit switch 28 Opening control input (radar,induction loops) Colours of the prewired service cable are shown on the left Control Card sales@indupart.co.uk 21

22 L6 L7 L1 L2 L3 L4 L5 LED 1 RED Photocell When the light beam between photocells is interrupted LED 1 switches off LED 2 RED Stop When the emergency push button is pushed LED 2 switches off. LED 3 RED Safety edge When the safety edge is pressed LED 3 switches off. LED 4 GREEN Pedestrian opening When the pedestrian opening push button,if pedestrian opening is required,is pushed LED 4 switches on LED 5 GREEN Standard opening When the opening push button is pushed LED 5 switches on. LED 6 RED Closed door limit switch The door is closed when LED 6 is switched off. LED 7 RED Open door limit switch The door is open at clear opening height when LED 7 is switched off. LED 7 LED 6 RED RED If both LED 6 and LED 7 are switched on the door is opening or closing. LED sales@indupart.co.uk

23 OPERATING MODE DIP SWITCH 1 ON DIP SWITCH 2 OFF Operating mode with closing timer. The door opens,stands open and after a certain time automatically closes. The opening push button always opens. If,for instance,the door is closing and the opening push button is pushed the door stops and opens again. DIP SWITCH 1 OFF DIP SWITCH 2 ON Operating mode without closing timer. The door opens and stands open. To close it,it must push the green push button again. The opening push button one time opens and the time after closes. If the door is opening and the opening push button is pushed the door stops. Pushing it again the door closes. DWELL TIME DIP SWITCH 5 ON To adjust the dwell time,i.e. the time when the door stands open before closing automatically (of course the operating mode must be with closing timer). 1. Switch DIP Switch 5 ON. 2. Push the opening push button. 3. The door opens and stands open. 4. Count the seconds you wish as dwell time. 5. Push again the opening push button. 6. The door closes. 7. After 5 seconds switch DIP Switch 5 OFF. Settings sales@indupart.co.uk 23