GLM SERIES CONTROL Users Manual Rev:

Size: px
Start display at page:

Download "GLM SERIES CONTROL Users Manual Rev:"

Transcription

1 GLM SERIES CONTROL Users Manual Rev: Connecting Power Page 2 Motor Terminal Wiring Diagrams Page 3 Getting Started / Setup Page 4 1. Obstruction Detection Devices Page 4 2. Checking Power and Direction Page 4 3. Limit switch connection Setting Page 5 4. Operation Page 7 5. Controller Page 8 Main Control Board (MCB) Layout Page 9 Expansion Board Page 10 Expansion Board Layout Page 12 DIP Switch Settings Page 13 Troubleshooting Page 14 Maintenance Page 15 Warranty / Guarantee Page 16 INTRODUCTION Congratulations on your purchase of the GLM SERIES unit. This component is specifically designed to suit our Mechanical Limit Industrial Grifco Operators. Its intended purpose is to provide the functions of the Maestro Main Control Board, (MCB) and its accessories. Supplied with your GLM SERIES control is a Maestro Receiver Card (MRC), Expansion Board (EB), a reflective PE Beam (PB008) and a Grifco Transmitter (GT4). D-M-ACG/019 1

2 CONNECTING POWER Precautions- The GLM Series Control must: - be connected via a device that is capable of being locked for maintenance - be connected via a suitable circuit breaker that disconnects all live conductors - have a handle of supply easily accessible and in the vicinity of the motor - be connected in accordance with the wiring rules of the country in which it is installed - not have control enclosures left open for extended periods (excess dust will void warranty) The GLM Series Control is available in both single and three phase models. The Control model can be identified by the label located on the MCB contactors or mains fuses cover. Carefully match the requirements of the motor to the correct configuration shown below. 2

3 MOTOR TERMINAL WIRING DIAGRAMS MODELS: Three Phase 3 Wire MODELS: Single Phase 4 Wire MODELS: Single Phase 3 Wire 3

4 DISCONNECT MAINS POWER TO THE SYSTEM BEFORE REMOVING COVERS. MAKE SURE THAT PEOPLE WHO INSTALL, MAINTAIN OR OPERATE THE DOOR FOLLOW THESE INSTRUCTIONS. IT IS ADVISED THAT THE INSTRUCTIONS BE KEPT IN A SAFE PLACE SO THAT YOU CAN REFER TO THEM QUICKLY WHEN YOU NEED TO. GETTING STARTED / SETUP 1. OBSTRUCTION DETECTION DEVICES Devices such as PE beams and Safety Bump Edges allow safe automatic closing of the door and can be wired directly into the MCB via an appropriate cable entry. The devices are wired into the obstruction inputs located next to the behaviour dip switches on the MCB shown below. PE SUP (or AUX OUT): Supply power for PE beam (24VAC, max *150mA) PE SW: Switch input from PE (Normally closed) BUMP: Bumper edge input (Normally open or resistor type) PE Beams (Part No. PB008) and Terminal Blocks (Part No. TB210) are all available from your local industrial door dealer or Grifco. *Important warning: Additional devices must not draw current from the MCB 24 volt circuit exceeding 150mA. Excessive load from connected devices will cause malfunction of the Maestro operator. This generally allows for up to 2 x photo beams (Grifco supplied). For additional loads, use a separately mounted power supply. Note: Turn the key to the MAN position. Ensure DIP switches 1 & 2 are ON, on the MCB. AUTO mode must not be used until installation is complete! 2. CHECKING POWER AND DOOR DIRECTION After the unit powers up check that the POWER ON indicator on the controller is lit. If the LIMIT ERROR indicator (orange) is lit the limit switch connection is incorrect (refer page 5). Extreme care must be taken when moving the door for the first time. The door should be positioned mid way between the top and bottom stops. If the direction is correct skip forward to the next step. If the direction of doors movement is opposite of what is shown on the control box, refer to Changing Door Direction on the next page. 4

5 CORRECT INCORRECT Changing Door Direction (if required) 1. Turn off power to unit. 2. Refer to page 3 (for Motor wire colour & wiring arrangement). You will need to switch over the X and Z Motor Terminals. 3. Return power and carefully assess the doors direction. The direction of the doors movement will now be reversed. EXTREME CARE SHOULD BE TAKEN BY SERVICE PERSONNEL. MOTOR CAN START WITHOUT WARNING IN AUTO MODE. THE ONLY WAY TO ENSURE THE MAESTRO OPERATOR WILL NOT START WITHOUT WARNING IS BY SWITCHING OFF MAINS POWER. 3. LIMIT SWITCH CONNECTION AND LIMIT SETTING CONNECTION YELLOW Using the cable and 90º quick connects provided, connect the cable from the limit switches (diagram above); to the limit socket (refer page 6): Note: The Black wire is not connected 5

6 LIMIT SETTING PROCEDURE WARNING: Limits are extremely sensitive; a small cam movement may correspond to a large amount of shutter travel. -ISOLATE MAINS BEFORE SETTING LIMITS -AVOID CRAMMING WIRES INTO LIMIT ENCLOSURE AS IT MAY AFFECT CAM MOVEMENT Follow the steps below: - Manually position the door in the centre of the opening. - Position one cam to depress a switch and the other so that it is well clear of the switch. (Note which switch it is that you have depressed.) - For controls with up and down functions: ~Supply power and activate control in the upward direction. ~If the shutter travels up then the limit switch noted above is the bottom limit. ~If the shutter doesn't move it is the top limit. - For single button controls: ~Supply power and push the button. ~If the shutter moves up, the switch noted above is the bottom limit. ~If it moves down then it is the top limit. -Isolate power and adjust the limit cams to depress the switches when the shutter reaches its open and closed positions. -Test the cam positioning and adjust if necessary. MOISTURE AND WATER CAN DESTROY THE CONTROL BOARDS. MAKE SURE UNDER ALL CIRCUMSTANCES THAT WATER, MOISTURE OR STORAGE MOISTURE CANNOT PENETRATE ANY OF THE CONTROL BOARDS. THE SAME APPLYS FOR OPENINGS AND CABLE ENTRIES. 6

7 4. OPERATION ENSURE all previous steps have been followed before proceeding with this part of the installation. The door should be moving up and down between the limits that have been set and the PE beam should be operational. If this is not the case return to the previous steps and correct the doors behaviour. NOTE: In manual (MAN) mode the door will only travel whilst the UP or DOWN buttons are being held. Given that the Expansion Board is utilised, Jumper 2 (JP2) on the Expansion Board must be fitted at all times. Once limits have been set and the Operator is working correctly in the manual mode it is time to test the AUTO functionality; AUTO MODE: When the key switch is turned to the AUTO position the door will travel upwards and downwards with only a single press of a valid auto input (i.e. any input wired directly into the expansion board or remotes). The door will stop at the set limits or when the STOP button is pressed. Note: This mode is only used in conjunction with an Obstruction Detection Device such as a PE beam or a Safety Bump Edge. Failure to do so may result in damage to property or injury to persons. Refer page 6. Setting Door Behaviour To set the Door Behaviour modes, adjust the DIP switches on the corner of the MCB (refer page 9 No. 4). The different combinations of DIP switches will suit different behaviours and obstruction detection devices installed. Desired Behaviour Latch Up Latch Down PE beam Installed Safety Bump Edge Installed DIP 1 DIP 2 DIP 3 DIP 4 Y N ON ON OFF OFF N Y OFF ON **OFF OFF Y Y ON ON **OFF OFF ** If using a 8k2 resistor type Safety Bump Edge, then set DIP 3 to ON AND 2 OFF Manual Operation The hand chain provided allows manual operation of the door at all times in which the motor is not in use. Use of the hand chain during powered operation of the door may result in damage to equipment or injury to the user. Ensure power is shut off before using manual chain. 7

8 5. CONTROLLER The Maestro Controller Panel is the user interface for the Operator. It consists of four buttons for control and setup, as well as three indicators to display the operator status. 1) UP - Moves the door upwards 2) DOWN - Moves the door downwards 3) STOP - Stops the door 4) SET - Used to clear error 5) POWER ON - Shows when the unit is mains powered 6) STATUS - Shows the status of the unit (refer page 14) 7) LIMIT ERROR When lit indicates no connection or incorrect wiring of limits (refer page 5) The Keyswitch Panel (pictured right) consists of, a dedicated AUTO, OFF, and dedicated MAN positon. OFF: When in OFF the Operator is completely inoperative. AUTO: AUTO is only selected when the door is in normal operations, where the user does not want to allow use of the UP and DOWN buttons on the Controller. The only button to function on the Controller will be STOP. MAN: MAN position only allows the use of the UP, STOP, DOWN and SET buttons on the Controller. This mode would be used when setting limits and while performing any routine maintenance on the door. AFTER THE INSTALLATION A FINAL TEST OF THE FULL FUNCTION OF THE SYSTEM AND WHERE PRESENT THE FULL FUNCTION OF THE SAFETY DEVICES MUST BE DONE. 8

9 MAIN CONTROL BOARD (MCB) The MCB is the heart of the Maestro. The diagram below provides an overview of the major components and access points. 9

10 EXPANSION BOARD The Expansion Board plays a major role in the construction of the GLM Series control. It allows for a vast range of functionality for many door automation applications, however it is typically aimed at satisfying car park requirements. Some of the automatic features include: Dedicated AUTO & dedicated MANUAL modes Auto close with user settable delay (0 to 300 seconds) Variable obstruction behaviour settings Trigger input with variable door action sequences Connection to industry standard 6 pin radio receiver cards Independent variable radio card response actions 4 status relays to allow connection to external devices Emergency Services open and close inputs CONNECTIONS Obstruction Detection Devices (Photo Beams & Safety Bump Strips etc) The Expansion Board requires that at least one obstruction detection device is connected to the MCB to operate correctly. Door Activation Inputs (Key Switches, Card Readers, Push Buttons etc) One of the most common inputs for a car park door operator is that which activates the door to open. This is generally connected to external / internal key switches, card readers, push button and the like to allow users to activate the door. If remote control is the only source of activation, these inputs will not be required. (For connection details refer page 12-J1). External Trigger Input An external trigger can be installed to give more control over the operator. Once installed the trigger can be used to open/close the door, go straight to third limit if set, hold open or delay close. By default the trigger is 24VDC input, however by fitting the contact jumper next to the terminals (Page 12-H4) you will switch to voltage free input. The behaviour of the trigger is set via the on board DIP switches. Refer to Trigger Input Behaviour on page 13. Status Relays Four status relays located on the expansion board allow external devices, such as lights, sirens and solenoids to be activated in various ways. Relays 1 and 2 are set to activate when door is OPEN and CLOSED respectively. Relays 3 and 4 can be configured via dipswitches (refer page 13). Each relay has a common, normally open, and normally closed connection. 6 Pin Receivers / Antenna Located on the expansion board is a 6 pinned header to suit industry standard 6 pin receiver cards (page 12-A7). Other style radio cards can be plugged in directly via the 3 position EXTERN RADIO terminals (page 12-A10). An ANTENNA can be wired to the adjacent terminals (page 12-A5). Emergency Input Controls These inputs are used in case of an emergency. They will open or close the door in all operating modes except OFF, overriding all other inputs. If an obstruction is detected during an emergency close, the operator will attempt to re-close after the obstruction is removed, regardless of the Door Close Retry settings. The connection points for the emergency inputs can be found on page 12-I3. 10

11 Typical Car Park Application (ref below for definition) SETTINGS For typical car park installations, all DIP switches are to be OFF. Jumper 2 (refer page 12-J6) must always be ON. In Auto the door is generally operated by a push button, card reader or remote control to activate the door in an opening sequence. The door will then automatically close after a user settable time. The obstruction detection input will command the door to open to the fully open position and resume closing after the obstruction has cleared. The Auto Close timer will not be restarted unless another open input is received. The Auto close timer is a dial type pot located in the corner of the Expansion Board where the DIP switches are also found (refer page 12-J11). By default it is set up at a range of 5 30 seconds (clockwise to increase). Range can be increased to 5 minutes by fitting Jumper 1 (refer page 12-J6). STATUS LEDS (refer page 12 E5) LED Description Colour Display Status Possible Solution Close Red Solid ON = Closed Flashing = Closing Open Green Solid ON = Open Flashing = Opening Error Yellow Solid ON = EB failed Power OFF&ON if still error, replace EB Check ribbon connection or replace Communications Orange Solid ON = EB to MCB comms error EB 24vdc b/up power 1 flash = detected 2 flash = Incompatible limits Reset limits 3 flash = No limits Set Set Limits Not an error, waiting for mains to resume Check DIPSWITCHES 2 and 3 on MCB 4 flash = MCB latch setting error 5 flash = EB ignored by MCB Check MCB for errors 11

12 LAYOUT The diagram below show the various inputs, outputs and components found on the Expansion Board. Throughout this manual, alpha-numeric references may be made to certain areas. Simply follow the grid locations to see the area being referred to. *CLOSED STATUS 12

13 EXPANSION BOARD DIP SWITCH SETTINGS Setting the Expansion Boards behaviour is done by adjusting 16 dipswitches located on it (refer page 12-K8). To adjust the Expansion Boards settings follow the table below. EB setting Dipswitches Setting EB mode source SW1 Factory Set> OFF AUTO with MCB Over-ride ON Use MANUAL-OFF-AUTO Switch Auto Close Disable SW2 Factory Set> OFF Auto Close ENABLED ON Auto Close DISABLED Obstruction Behaviour SW3 SW4 Factory Set> OFF OFF Stop and retract to last upper limit OFF ON Stop and retract while obstruction remains ON OFF Stop with 2 second retract only ON ON Stop Door Close Retry SW5 Factory Set> OFF Door will close after obstruct behaviour concludes ON Door Close Retry DISABLED, only Auto Close will close the door after obstruction behaviour, and time out concludes Vehicle Close SW6 Factory Set> OFF Vehicle Close DISABLED ON Door will close after obstruction clears, whilst open, opening or closing Open Button Behaviour SW7 SW8 Factory Set> OFF OFF Open only, stop and open when closing OFF ON Reverse direction during opening and closing ON OFF Stop then reverse during opening, reverse during closing ON ON Press to Stop, then again to reverse during opening and closing Receiver Behaviour SW9 SW10 Factory Set> OFF OFF Open only, stop and open when closing OFF ON Reverse direction during opening and closing ON OFF Stop then reverse during opening, reverse during closing ON ON Press to Stop, then again to reverse during opening and closing *Trigger Input Behaviour SW11 SW12 Factory Set> OFF OFF Close * Trigger is 24VDC input OFF ON Door will open to third limit ON OFF Door will go to open limit and remain while input remains held ON ON Custom Input via Parameters (Default - delay close as per timer pot) Status Relay 3 Function SW13 SW14 Factory Set> OFF OFF ON when Door Moving OFF ON ON when Door Moving, with 1Hz Oscillation ON OFF ON Door Moving, 1 minute Time Extension ON ON Custom (Default- on during obstruction, stays on for 2 sec after clear) Status Relay 4 Function SW15 SW16 Factory Set> OFF OFF Relay is on when Service Required OFF ON Relay flashes every second when service is required ON OFF Unlock function ON ON Custom Settings (Default On if door has not closed for >5mins) 13

14 TROUBLESHOOTING Status Indicator (Green) Flash / Problem Table for Main Control Board No. flashes/ Problem Solid ON Motor running 1 Running on EB battery 2 Photo beam and/or Bump edge obstruction 3 Bump edge failure (Resistor type only) Meaning Possible causes Possible Solutions PE beam obstructed Bumper edge pressed Bumper edge connection lost 4 MCB error Internal Error Severe close range frequency 5 EB internal error Fatal Error EB disconnected from MCB 6 Maximum starts per hour Operator used above maximum reached rated starts per hour 7 Max run time reached Operator used above maximum rated running time 8 Current Imbalance Phase missing (only applicable to 3 phase operators) Clear obstruction Remove pressure from bump edge Check / repair wiring of resistor type bump edge Power off, and on, or replace MCB Replace EB Return EB to the installation Use operator less frequently Upgrade to a high cycle operator Use operator less frequently Upgrade to a high cycle operator Check mains wiring Check fuses Check motor connections and / or phase current 9 Locked Rotor overload Motor stalled Check for objects causing interference to door operation Check for damage to motor Upgrade to a larger operator 10 Severe Running overload Extreme load on door Check for objects causing interference to door operation Check for damage to motor Upgrade to a larger operator 11 Running overload Excess load Check for objects causing interference to door operation Check for damage to operator Upgrade to a larger operator Reduce size of operator sprocket or increase size of door sprocket Increase overload setting (warranty will be voided) 12 Thermal overload Motor overheating Use operator less frequently Upgrade to a high cycle operator 13 Travel time high Motor fault causing slow speed Check door for mechanical failure Excess load on door 14 Direction error Motor connections altered Bad connection to Limit Socket 15 Under speed Motor running under speed Excess load on door Change door direction and reset limits Carefully spray RJ11 MCB with CRC 2.26 Contact treatment Check door for mechanical failure or motor fault Carefully spray RJ11 MCB with CRC 2.26 Contact treatment Constant flash Due for service Door is due for routine service Contact your local door dealer to arrange service No Lights Displayed Push button not responding Power failure No lights on MCB or Controller *With lights on at MCB Operator does not drive up and / or down Blown fuse Power supply not correctly connected *Bad connection to Controller Bad connection to Controller Faulty Controller cable Controller buttons forced and dislodged from rear of lid Check all fuses Check power supply wiring *Refer below if lights are on at MCB and not on Controller *Check RJ45 plugs are clipped in securely at Controller and MCB *Carefully spray RJ45 Controller & MCB socket with CRC 2.26 contact treatment *Replace Controller cable *Replace Controller Open or Close button not responding but green light comes on Coil failure if green light on whilst holding up or down button and operator does not move in one direction Extreme vibration or impact during transit Replace MCB IMPORTANT NOTE: If a problem is found with an installation, be sure to read the troubleshooting guide thoroughly and if the problem persists call Grifco for technical assistance on or technical@grifco.com.au 14

15 MAINTENANCE The Maestro is equipped with smart logic to indicate when your industrial door will require servicing. When the STATUS indicator constantly flashes quickly, please contact your industrial door dealer to arrange a routine door service. Overload Adjustment and Settings This process is not necessary for typical applications. Varying overload levels from the Factory Set level will void warranty. To view full load current (FLC) overload setting (with limits set) Drive door to closed limit Press and hold STOP and CLOSE for 10 seconds Status LED will light up indicating number of amps To read number of amps, follow the Reading Status Flashes routine described below To view max amps (with limits set) Drive door to closed limit Press and hold CLOSE for 10 seconds After 10 seconds and while still holding CLOSE, press and release the STOP button Status LED will light up indicating maximum amps drawn To read max amps, follow the Reading Status Flashes routine described below To change full load current (FLC) overload setting While holding STOP, press the SET button 3 times The LIMIT ERROR indicator will start flashing signifying limit setting mode Press and hold the STOP button While holding STOP, press either UP or DOWN to increase or decrease the FLC by 0.1A with each press The LIMIT ERROR indicator will flash with every successful increment/decrement The FLC can be modified a maximum of 1.5A per session Once done release the STOP button, then press the STOP button again to exit Reading Status Flashes STATUS indicator will start flashing to signify the value of the least significant digit of the overall number, or in the case of amperage values this will be the value after the decimal point. A solidly lit indicator stands for zero Press set to view the next digit Continue previous step until the STATUS indicator flashes quickly for 1 sec then goes out. This signifies that the entire number has been displayed To reset error (This process indicates there has been a severe problem. Persistent resetting will void warranty and may do damage to the door or operator) Hold the STOP button for 10 seconds While still holding the STOP button, press and release the SET button The STATUS indicator should flash quickly for 1 second. Any errors that were flashing should have stopped. 15

16 16

installation and users manual for edrive commercial door opener

installation and users manual for edrive commercial door opener installation and users manual for edrive commercial door opener Chamberlain Australia Pty Ltd PO Box 1446, Lane Cove NSW 1595, Australia Phone toll free 1800 638 234 www.chamberlainanz.com Chamberlain

More information

CB CONTROL BOARD INSTRUCTION MANUAL VERSION 1.03 DATE 30/10/2000

CB CONTROL BOARD INSTRUCTION MANUAL VERSION 1.03 DATE 30/10/2000 CB-9 3.02 CONTROL BOARD INSTRUCTION MANUAL VERSION 1.03 DATE 30/10/2000 FIRMWARE VERSION 1.09 Thank you for choosing the CB-9 control system. We encourage you to read and understand this manual prior to

More information

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI II 1400-6 ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI ACSI 1426-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1092, REV. C INSTALLATION For C-UL Listed applications,

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

TRIPS AND FAULT FINDING

TRIPS AND FAULT FINDING WWW.SDS.LTD.UK 0117 9381800 Trips and Fault Finding Chapter 6 6-1 TRIPS AND FAULT FINDING Trips What Happens when a Trip Occurs When a trip occurs, the drive s power stage is immediately disabled causing

More information

Note: Read this manual carefully before installing the operator and place this installation manual in an accessible place near the operator.

Note: Read this manual carefully before installing the operator and place this installation manual in an accessible place near the operator. Installation & Instruction Manual Electronic Control Board (ECB) Note: Read this manual carefully before installing the operator and place this installation manual in an accessible place near the operator.

More information

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery

More information

CALTRAP INSTALLATION AND OPERATIONS MANUAL

CALTRAP INSTALLATION AND OPERATIONS MANUAL INSTALLATION AND OPERATIONS MANUAL NOTE Please read this entire installation and operations manual before energizing the. Safety Considerations: Installing and servicing capacitor equipment can be hazardous.

More information

R & D SPECIALTIES ROTROL I USER'S MANUAL

R & D SPECIALTIES ROTROL I USER'S MANUAL R & D SPECIALTIES ROTROL I USER'S MANUAL TABLE OF CONTENTS INTRODUCTION...2 SPECIFICATIONS...2 CONTROLS AND INDICATORS...3 TIME DELAYS...4 INSTALLATION...5 SYSTEM OPERATION...9 TROUBLESHOOTING...13 OPTIONAL

More information

Setup and Programming Manual

Setup and Programming Manual Microprocessor and Handy Terminal Setup and Programming Manual Versions U04 to U19 for Sliding Door Systems P/N 159000 Rev 7-2-07 The manufacturer, NABCO Entrances, Inc. suggests that this manual be given

More information

User Manual. T6 Tachometer. Online: Telephone: P.O. Box St. Petersburg, Florida 33736

User Manual. T6 Tachometer. Online:   Telephone: P.O. Box St. Petersburg, Florida 33736 User Manual T6 Tachometer Online: www.phareselectronics.com Telephone: 727-623-0894 P.O. Box 67251 St. Petersburg, Florida 33736 Table of Contents Overview... 1 Description... 1 Wiring... 1 T6 Tachometer

More information

Door Control Panel TS 960. instructions. (Design and functions subject to change) /

Door Control Panel TS 960. instructions. (Design and functions subject to change) / Electrical operating Operating instructions Door Control Panel TS 960 GB (Design and functions subject to change) 51171098 / 10.2002 OPERATING INSTRUCTIONS PAGE SAFETY DIRECTIONS...4 FUNCTION OVERVIEW...6

More information

Optimal Series. Automatic Transfer Switch. Installation and User Manual for the OPT2225 Automatic Transfer Switch. Full Version

Optimal Series. Automatic Transfer Switch. Installation and User Manual for the OPT2225 Automatic Transfer Switch. Full Version Optimal Series Automatic Transfer Switch Installation and User Manual for the OPT2225 Automatic Transfer Switch Full Version File: OPT2225 Rev2.5.doc November, 2004 2 Thank You For Purchasing This DynaGen

More information

Installation and Maintenancee Manual

Installation and Maintenancee Manual Installation and Maintenancee Manual Commercial Boom Gate Operator Model: GDS BOOM 4 and 6 A.B.N. 62 059 806 405 Nov 2013 Section No: CONTENTS Page Number: 1 Safety Precautions 3 2 Specifications 4 3 Mechanical

More information

A problem with the motor windings. A phase loss on mains terminals L1, L2, or L3 during run mode. Parameter 2-3 Current Imbalance Delay.

A problem with the motor windings. A phase loss on mains terminals L1, L2, or L3 during run mode. Parameter 2-3 Current Imbalance Delay. 10 Troubleshooting When a protection condition is detected, the VLT Soft Starter MCD 500 writes this condition to the event log and may also trip or issue a warning. The soft starter response depends on

More information

MANUAL TROUBLESHOOTING. ECM Motor. ECM / ECM-DX Series. v100 Issue Date: 08/15/ Price Industries Limited. All rights reserved.

MANUAL TROUBLESHOOTING. ECM Motor. ECM / ECM-DX Series. v100 Issue Date: 08/15/ Price Industries Limited. All rights reserved. MANUAL ECM Motor ECM / ECM-DX Series v100 Issue Date: 08/15/17 2017 Price Industries Limited. All rights reserved. ECM MOTOR TABLE OF CONTENTS ECM Motor Background...1 ECM Motor Power and Control Connectors...2

More information

DC Variable Speed Drive Panel

DC Variable Speed Drive Panel DC Variable Speed Drive Panel Installation, Operation & Maintenance Instruction Manual Bulletin #: CC-IOM-0103-D Manufacturers of Quality Pumps, Controls and Systems ENGINEERED PUMP OPERATIONS 2883 Brighton

More information

2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE

2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause

More information

RE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW

RE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW Page 1 of 6 3-Phase Panel Mount 86 and 105kW Features: Benefits: 0-10Vdc, 0-5Vdc, 4-20mA or manual via potentiometer control input Over temperature protection with auto reset Enclosed panel mounting Efficient

More information

Modulating Furnace Information. Warning on Meter Setting - Read First!

Modulating Furnace Information. Warning on Meter Setting - Read First! Modulating Furnace Information Pressure Transducer Pressure DC Volts 0.00" 0.25 0.20" 0.63 0.25" 0.72 0.30" 0.82 0.35" 0.91 0.40" 1.00 0.45" 1.09 0.50" 1.19 0.55" 1.28 0.60" 1.38 0.65" 1.47 0.70" 1.56

More information

Flight Systems. Replacement for KASSEC DESCRIPTION

Flight Systems.   Replacement for KASSEC DESCRIPTION DESCRIPTION The is a universal generator controller that will start, stop, and provide engine protection for most generators. Universal replacement for both the 90353 and 90354 KASSEC Compatible with most

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

MCD 500 Service Manual. Functional Tests 5 Power Circuit Test 5 Start Performance Test 5 Run Performance Test 6 Trip Messages 6 General Faults 10

MCD 500 Service Manual. Functional Tests 5 Power Circuit Test 5 Start Performance Test 5 Run Performance Test 6 Trip Messages 6 General Faults 10 Contents Contents 1 Warnings 3 2 Troubleshooting 5 Functional Tests 5 Power Circuit Test 5 Start Performance Test 5 Run Performance Test 6 Trip Messages 6 General Faults 10 3 Service Instructions 13 Frame

More information

Valcom Failsafe Unit. 1620ESv2 SERIES. Operation and Maintenance Manual

Valcom Failsafe Unit. 1620ESv2 SERIES. Operation and Maintenance Manual Valcom Failsafe Unit 1620ESv2 SERIES Operation and Maintenance Manual Table of Contents Section Title Page 1. - Introduction.. 2. - Unpacking the Failsafe unit. 3. - Installation 3.1 - Auto / Timed UPS

More information

Gate & Door Controller with LCD and Intelligent Technology

Gate & Door Controller with LCD and Intelligent Technology 2nd Edition Gate & Door Controller with LCD and Intelligent Technology 24Sv1 and 12Sv1 Motor Controllers Setup and Technical information for single motor controller for gates & doors Includes latest Intelligent

More information

TEL: G&C Electronics CC E. T.

TEL: G&C Electronics CC E. T. TEL: +27 21 448 6774 G&C Electronics CC FAX: +27 21 447 7794 E. T. CK 89/31531/23 E-mail : etsystems@icon.co.za Internet: www.et.co.za 15 Nelson Road P.O. Box 34524 Observatory Groote Schuur Cape Town

More information

Application Engineering

Application Engineering Application Engineering February, 2009 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital Compressor

More information

Aftermarket Interface Module

Aftermarket Interface Module An ISO 9001:2008 Registered Company Aftermarket Interface Module (2015-2018 Ford Transit) AIM514-B High Side Solenoid type Coolant Valve Control AIM515-B Motor Reversing type Coolant Valve Control Introduction

More information

HP21 SERVICE SUPPLEMENT UNIT INFORMATION. TSC6 Two-Speed Control

HP21 SERVICE SUPPLEMENT UNIT INFORMATION. TSC6 Two-Speed Control SERVICE UNIT INFORMATION SUPPLEMENT HP21 Corp. 9426 L10 Litho U.S.A. All HP21-4 and -5 units (single and three phase) are equipped with a TSC6 two-speed control. The TSC6 (A14) two-speed control contains

More information

CORESENSE DIAGNOSTICS FOR STREAM REFRIGERATION COMPRESSORS

CORESENSE DIAGNOSTICS FOR STREAM REFRIGERATION COMPRESSORS Date of last update: Apr-15 Ref: D7.8.4/0112-0415/E Application Engineering Europe CORESENSE DIAGNOSTICS FOR STREAM REFRIGERATION COMPRESSORS CoreSense Diagnostics for Stream Refrigeration Compressors...

More information

CONTROL UNIT BIOS2. Manual for installation. Programmable Control board for wings gates.

CONTROL UNIT BIOS2. Manual for installation. Programmable Control board for wings gates. Programmable Control board for wings gates www.remotecontrolgates.co.uk Manual for installation Compatible from firmware version BIOS2BT02 CONTROL UNIT BIOS2 1. Introduzione The control unit BIOS2 is particularly

More information

Observe all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning.

Observe all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning. Introduction OPERATING INSTRUCTIONS: MCD REMOTE OPERATOR Order Codes: 175G94 (for MCD 2) 175G361 + 175G9 (for MCD 5) 175G361 (for MCD 3) 1. Introduction 1.1. Important User Information Observe all necessary

More information

2904 Power Supply Installation Instructions I-EA00041

2904 Power Supply Installation Instructions I-EA00041 FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and

More information

Application Engineering Europe

Application Engineering Europe Date of last update: Feb-12 Ref: D7.8.4/0112-0212/E Application Engineering Europe CORESENSE DIAGNOSTICS FOR STREAM REFRIGERATION COMPRESSORS 1/17 1 Introduction CoreSense is an ingredient brand name for

More information

PF3100 TROUBLESHOOTING SOLUTIONS TO COMMON PROBLEMS. v1.1 Revised Nov 29, 2016

PF3100 TROUBLESHOOTING SOLUTIONS TO COMMON PROBLEMS. v1.1 Revised Nov 29, 2016 PF3100 TROUBLESHOOTING SOLUTIONS TO COMMON PROBLEMS v1.1 Revised Table of Contents 1 Common Alarms and Warnings... 1 2 Common Issues... 6 2.1 Communication problems... 6 2.1.1 Controller communication

More information

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL INSTALLATION INSTRUCTIONS AND OPERATION MANUAL UL325-2010 Compliant Commercial and Industrial Door Operator Logic Control Continuous Duty IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk

More information

OWNER S MANUAL HC1/HC2 INSTRUCTIONS EN FRANÇAIS AU VERSO

OWNER S MANUAL HC1/HC2 INSTRUCTIONS EN FRANÇAIS AU VERSO /MD OWNER S MANUAL HC1/HC2 INSTRUCTIONS EN FRANÇAIS AU VERSO FCC COMPLIANCE This device complies with FCC rules, and is subject to the following conditions: (1) This device may not cause harmful interference.

More information

MODEL 422 Submersible Pump Controller

MODEL 422 Submersible Pump Controller MODEL 422 Submersible Pump Controller Monitors True Motor Power (volts x current x power factor) Detects Motor Overload or Underload Operates on 120 or 240VAC, Single-phase or 3-phase Built-in Trip and

More information

Product Guide: Series III Pump Control Board Set (RoHS)

Product Guide: Series III Pump Control Board Set (RoHS) revised 04/08/10 Description: The Series III Pump Control Board Set provides motor drive and pump control for a wide assortment of pumps from Scientific Systems, Inc. The assembly consists of two circuit

More information

ATOTH-G Series BLDC Motor Controller. User s Manual

ATOTH-G Series BLDC Motor Controller. User s Manual ATOTH-G Series BLDC Motor Controller User s Manual Contents Chapter One Summary...1 Chapter Two Main Features and Specifications.2 2.1 Basic Functions...2 2.2 Features... 5 2.3 Specifications...6 Chapter

More information

User Manual. 1. Introduction

User Manual. 1. Introduction User Manual 1. Introduction The Tactile Loop Controller has been designed to provide specific logic outputs from a patented EzyLoop Systems tactile Surface Mounted Switch Pad intended primarily for pedestrian

More information

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL INSTALLATION INSTRUCTIONS AND OPERATION MANUAL Commercial and Industrial Fire Door Operator Logic Control Restricted Duty Fire Door Operators IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk

More information

Te 803 Electronic Controller. Service, Operation & Technical Information Manual

Te 803 Electronic Controller. Service, Operation & Technical Information Manual Te 803 Electronic Controller Service, Operation & Technical Information Manual WARNING! Technical descriptions and data given in this document are accurate, to the best of our knowledge, but can be subject

More information

3200NT Timer Service Manual

3200NT Timer Service Manual Service Manual Valve Serial Number Valve Position 1-LEAd 2-LAg 3-LAg 4-LAg IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specifications Sheet.....................................................................

More information

Safe & Secure Series Electric Actuator with Internal Battery Back-up Installation, Operation & Maintenance Manual

Safe & Secure Series Electric Actuator with Internal Battery Back-up Installation, Operation & Maintenance Manual Safe & Secure Series Electric Actuator with Internal Battery Back-up Installation, Operation & Maintenance Manual For Use with: SNS4, SNS6, SNS10 & SNS15 Models Additional supplements may be needed for

More information

LV101 DCC Power Station

LV101 DCC Power Station LV101 Power Station 1 Ultra clean DCC Track Power Adjustable DCC Track Voltage Opto-isolation interface for Safety Short and overload protection Designed to meet Proposed NMRA Power Station Interface RP

More information

ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual

ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual Headquarters : No.3, Lane 201, Chien Fu St., Chyan Jenn Dist., Kaohsiung, TAIWAN Tel : + 886-7-8121771 Fax : + 886-7-8121775 URL : http://www.kutai.com.tw

More information

Single or Double 240VAC motor control for domestic and industrial gates and doors.

Single or Double 240VAC motor control for domestic and industrial gates and doors. COBO30 Double 240V Motor Drive Controller Features For 240Volt Motors Auto Closing Open Only Security Closing and Extended Lock Pulse (user selectable) Travel Timer Push Button Input Photo Cell Input Option

More information

OPERATING AND MAINTENANCE MANUAL. Primary Current Injection Test Set. 750ADM-H mk2

OPERATING AND MAINTENANCE MANUAL. Primary Current Injection Test Set. 750ADM-H mk2 OPERATING AND MAINTENANCE MANUAL Product: Type: Primary Current Injection Test Set 750ADM mk2 750ADM-H mk2 DESIGNED AND MANUFACTURED BY: T & R Test Equipment Limited 15-16 Woodbridge Meadows, Guildford,

More information

INSTALLATION GUIDE. FCC ID NOTICE

INSTALLATION GUIDE.  FCC ID NOTICE REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This

More information

CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet

More information

Continuing Education Course #206 Introduction to Designing Machine Control Systems Part 2

Continuing Education Course #206 Introduction to Designing Machine Control Systems Part 2 1 of 5 Continuing Education Course #206 Introduction to Designing Machine Control Systems Part 2 1. Continuing to answer the following questions indicates that you understands that the presented material

More information

Installation & Service Manual

Installation & Service Manual Installation & Service Manual for M² Sync Slideout Control Box #1510000122 CONTENTS Introduction Installation Installation Problems Program Mode Operation Mode Preventative Maintenance Fault Diagnostics

More information

B-RAD Select USER MANUAL TABLE OF CONTENTS

B-RAD Select USER MANUAL TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS... 1 MANUAL REVISION HISTORY... 2 IMPORTANT SAFETY NOTICE... 3 1.0 General Information... 5 1.1 System Components... 5 1.2 Specifications... 5 1.2.1 Torque Ranges...

More information

Application Engineering

Application Engineering Application Engineering March 2011 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital compressor or the

More information

2015 EDITION SUBMERSIBLE MOTORS AIM MANUAL. APPLICATION INSTALLATION MAINTENANCE 60 Hz, Single-Phase and Three-Phase Motors. franklinwater.

2015 EDITION SUBMERSIBLE MOTORS AIM MANUAL. APPLICATION INSTALLATION MAINTENANCE 60 Hz, Single-Phase and Three-Phase Motors. franklinwater. 0 EDITION AIM MANUAL SUBMERSIBLE MORS APPLICATION INSTALLATION 60 Hz, Single-Phase and Three-Phase Motors franklinwater.com All Motors System Troubleshooting Motor Does Not Start A. No power or incorrect

More information

Cat/DCG-6D1I/07-08/03/Ver 1 Page 2/10

Cat/DCG-6D1I/07-08/03/Ver 1 Page 2/10 Cat/DCG-6D1I/07-08/03/Ver 1 Page 2/10 Index 1.1 Introduction 1.2 Salient Feature of the DGC-6D 1.2.1 Protection & Supervision 1.2.2 Measurement & Display 1.2.3 LED Indications 1.2.4 Timer 1.3 Function

More information

MAGNETIC MOTOR STARTERS

MAGNETIC MOTOR STARTERS Chapter 6 MAGNETIC MOTOR STARTERS 1 The basic use for the magnetic contactor is for switching power in resistance heating elements, lighting, magnetic brakes, or heavy industrial solenoids. Contactors

More information

SECEUROGLIDE ROLLER GARAGE DOORS, SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS

SECEUROGLIDE ROLLER GARAGE DOORS, SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS Operating & Maintenance Instructions SECEUROGLIDE ROLLER GARAGE DOORS, July 2007 Issue 4 SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS Page 1. General Instructions 2 2. Operating

More information

SAFE AND SECURE EXTREME R MOTOR OWNER'S MANUAL MODEL PRO-FDG FOR TECHNICAL SUPPORT PLEASE CALL 1-(855) OPERATOR SERIAL#

SAFE AND SECURE EXTREME R MOTOR OWNER'S MANUAL MODEL PRO-FDG FOR TECHNICAL SUPPORT PLEASE CALL 1-(855) OPERATOR SERIAL# SAFE AND SECURE EXTREME R MOTOR OWNER'S MANUAL MODEL PRO-FDG FOR TECHNICAL SUPPORT PLEASE CALL 1-(855) 594-4969 3121B(4) ECN 1288 BY TG 2/6/15 OPERATOR SERIAL# PRO-FDG MOTOR OPERATORS MOTOR OWNER'S MANUAL

More information

INSTALLATION AND INSTRUCTION MANUAL MODELS: PRO-T, PRO-TB

INSTALLATION AND INSTRUCTION MANUAL MODELS: PRO-T, PRO-TB INSTALLATION AND INSTRUCTION MANUAL MODELS: PRO-T, PRO-TB AUG, 2010 2 TABLE OF CONTENTS PAGE: VERIFICATION OF OPERATOR AND HARDWARE 3 SPECIFICATIONS 4 SAFETY INSTRUCTIONS 5 INSTALLATION 6 ELECTRICAL CONNECTIONS

More information

PowerOhm Installation Manual for BM R Series Braking Modules

PowerOhm Installation Manual for BM R Series Braking Modules PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

UL/NEMA Type 1 & Type 12 FRENIC-HVAC Combination VFD

UL/NEMA Type 1 & Type 12 FRENIC-HVAC Combination VFD UL/NEMA Type 1 & Type 12 FRENIC-HVAC Combination VFD Safety Precautions Read this manual thoroughly before proceeding with installation, connections (wiring), or maintenance and inspection. Ensure you

More information

Induction Power Supplies

Induction Power Supplies Induction Power Supplies 7.5kW; 135 400kHz 480V version (Integral Heat Station) User s Guide Model 7.5-135/400-3-480 SMD Control Brds Rev. D 5/08 Table of Contents 1. Specifications and features...3 2.

More information

5220 AUTOMATIC MAINS FAILURE MODULE OPERATING MANUAL

5220 AUTOMATIC MAINS FAILURE MODULE OPERATING MANUAL 5220 AUTOMATIC MAINS FAILURE MODULE OPERATING MANUAL > Section DSE Model 5220 Automatic Mains Failure & Instrumentation System Operators Manual TABLE OF CONTENTS

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

INSTALLATION GUIDE Table of Contents

INSTALLATION GUIDE Table of Contents CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2

More information

Easy Start. 364 (3 ton) Soft Starter 368 (6 ton) Soft Starter. Installation Manual

Easy Start. 364 (3 ton) Soft Starter 368 (6 ton) Soft Starter. Installation Manual Easy Start 364 (3 ton) Soft Starter 368 (6 ton) Soft Starter Installation Manual Micro Air Corporation Phone (609) 259-2636 124 Route 526. www.microair.net Allentown NJ 08501 Fax (609) 259-6601 Retrofit

More information

Burden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM

Burden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM Contents Section Page 1.0 Introduction 1 2.0 Specification 1-4 3.0 Installation 5-8 4.0 Programming 9-10 5.0 Menus 10-12 6.0 Fault Finding/Diagnostics 12-13 7.0 Communication 13 8.0 Setting Up 13-16 1.0

More information

OnCommand Troubleshooting Guide Hayward Industries

OnCommand Troubleshooting Guide Hayward Industries OnCommand Troubleshooting Guide 2010 Hayward Industries Table of Contents Safety Precautions Page 1 Overview Pages 2-5 Software Troubleshooting Page 6 Local Display Pages 7-8 Relays Pages 9-10 Heaters

More information

CB-9 CONTROL BOARD INSTRUCTION MANUAL

CB-9 CONTROL BOARD INSTRUCTION MANUAL CB-9 CONTROL BOARD INSTRUCTION MANUAL AUGUST 95 The CB-9 control board is designed to automate 1 or 2 A.T.A swing gate or sliding gate drive units. This instruction manual gives detailed instructions on

More information

Senior Swing Control Box. Table of Contents

Senior Swing Control Box. Table of Contents *740100* 740100 2800 Overhead Consealed Series 9500 Surface Applied Series Senior Swing Control Box Installation Instructions important These instructions are presented in step-by-step sequence. It is

More information

MD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version

MD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version MD10 Engine Controller Installation and User Manual for the MD10 Engine Controller. Full Version File: MartinMD10rev1.4.doc May 16, 2002 2 READ MANUAL BEFORE INSTALLING UNIT Receipt of shipment and warranty

More information

e-ask electronic Access Security Keyless-entry

e-ask electronic Access Security Keyless-entry e-ask electronic Access Security Keyless-entry Multiplex System Multiplex System Installation & Instructions (UM15 ~ 22272-03) Table of Contents Introduction... 1 Standard e-fob Operation and Features...

More information

AUTOMATIC CONTROL ROLLING DOOR OPENER

AUTOMATIC CONTROL ROLLING DOOR OPENER AUTOMATIC CONTROL ROLLING DOOR OPENER INSTALLATION INSTRUCTION AUTOMATIC OBSTRUCT PHOTOELECTRIC BEAM ROLLING CODE SYSTEM AUTO CLOSE DOOR ANTI-THEFT SYSTEM INSTALLATION INSTRUCTION AND RDO OWNERS MANUAL

More information

J3C-L Nm Smart Electric Valve Actuator Failsafe Function Type: J3C Model: L140-BSR

J3C-L Nm Smart Electric Valve Actuator Failsafe Function Type: J3C Model: L140-BSR Failsafe Function Type: JC Model: L140-BSR Feature rich J+J multi-voltage smart electric actuator with LED status light and function conversion kits. Overview The JC-L140 low voltage electric valve actuator

More information

PowerOhm Installation Manual for BM R Series Braking Modules

PowerOhm Installation Manual for BM R Series Braking Modules PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING

Requirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO

More information

Roll Up Door Operator

Roll Up Door Operator INSTRUCTIONS & OWNERS MANUAL Roll Up Door Operator 2 INDEX Preparation before installation 4. Terms and definitions 5. Pictures & names of parts 6. Mounting the weight bar 7. Installing the operator 7.

More information

CONTROL FEATURES AVAILABLE OPTIONS

CONTROL FEATURES AVAILABLE OPTIONS Vari Speed A2000 TABLE OF CONTENTS Control Features Options Application Data Operating Condition s Control Ratings Chart Mounting Dimensions Installation and Wiring Typical Wiring Diagram Schematic (Block

More information

EC200 ELECTRONIC CONTROL SYSTEM

EC200 ELECTRONIC CONTROL SYSTEM 1 INTRODUCING THE EC200 ELECTRONIC CONTROL SYSTEM With the use of new technology and an innovative approach to user interfacing, the EC200 Power Control System provides a complete control solution for

More information

Installation and Maintenance Instructions. World Leader in Modular Torque Limiters. PTM-4 Load Monitor

Installation and Maintenance Instructions. World Leader in Modular Torque Limiters. PTM-4 Load Monitor World Leader in Modular Torque Limiters Installation and Maintenance Instructions PTM-4 Load Monitor 1304 Twin Oaks Street Wichita Falls, Texas 76302 (940) 723-7800 Fax: (940) 723-7888 E-mail: sales@brunelcorp.com

More information

OPERATING INSTRUCTION: DGC-6D/6D1I

OPERATING INSTRUCTION: DGC-6D/6D1I OPERATING INSTRUCTION: DGC-6D/6D1I GCB Auto Man Stop Fail - PROCOM Pvt Ltd MRM PROCOM Plot No. : 20-21, Industrial Estate, Sector - 59, Phase-II, Faridabad (Haryana) Ph.: 0129-4700400(10 Lines) Email:

More information

DLKEK3HN INSTALLATION INSTRUCTIONS

DLKEK3HN INSTALLATION INSTRUCTIONS DLKEK3HN INDEX: INSTALLATION INSTRUCTIONS WIRING INSTRUCTIONS... PG 2-5 LED STATUS INDICATOR... PG 6 VALET/OVERRIDE BUTTON... PG 6 SHOCK SENSOR... PG 7 PROGRAMMABLE JUMPER-PINS... PG 7 PROGRAMMING REMOTE

More information

Sectional And Tilting Door Opener

Sectional And Tilting Door Opener Sectional And Tilting Door Opener Installation Instructions and User Guide FS 600 FS 1000 FS 1200 600N 1000N 1200N FS 600-Speed FS 1000-Speed 600N 1000N S/N WARNING Please read the manual carefully before

More information

INSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC).

INSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC). P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com ALPHA-3v2 Electronic Speed Controller Supplied for

More information

ACC Series Power Conditioner OPERATION & INSTALLATION MANUAL

ACC Series Power Conditioner OPERATION & INSTALLATION MANUAL ACC Series Power Conditioner OPERATION & INSTALLATION MANUAL PHASETEC digital power conditioners are designed to safely operate electrical equipment in the harshest power quality environments. With a wide

More information

TECHNICAL MANUAL. Inverter / Charger Combi. Combi SW 12V 1600VA Réf : PF Combi SW 24V 3800VA Réf : PF NOT_COMBI_SW-00

TECHNICAL MANUAL. Inverter / Charger Combi. Combi SW 12V 1600VA Réf : PF Combi SW 24V 3800VA Réf : PF NOT_COMBI_SW-00 TECHNICAL MANUAL EN Inverter / Charger Combi Combi SW 12V 1600VA Réf : PF.16088 Combi SW 24V 3800VA Réf : PF.16089 SAFETY PRECAUTIONS TO PREVENT ANY RISK OF ELECTRIC SHOCK OR FIRE, READ THIS MANUAL CAREFULLY

More information

ADDENDUM MODEL S3 OPERATORS Models: SL/540/570/580/590 & SW420/470/490

ADDENDUM MODEL S3 OPERATORS Models: SL/540/570/580/590 & SW420/470/490 ADDENDUM MODEL S3 OPERATORS Models: SL/540/570/580/590 & SW420/470/490 This addendum is to be used in conjunction with the owner s manual included with this operator. Refer to this addendum for all programming

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

12 Series Linear Electric Actuator Installation, Operation & Maintenance Manual

12 Series Linear Electric Actuator Installation, Operation & Maintenance Manual 12 Series Linear Electric Actuator Installation, Operation & Maintenance Manual TELEPHONE: +1-859-727-7890 TOLL FREE: +1-800-662-9424 FAX: +1-859-727-4070 E-MAIL: DVOGES@INDELAC.COM MROBINSON@INDELAC.COM

More information

EAGLETRON II REMOTE CONTROL OPERATOR and MAINTENANCE. Remote Control Procedure

EAGLETRON II REMOTE CONTROL OPERATOR and MAINTENANCE. Remote Control Procedure EAGLETRON II REMOTE CONTROL OPERATOR and MAINTENANCE Remote Control Procedure WARNING! DO NOT OPERATE REMOTE CONTROL UNLESS YOU HAVE A CLEAR VIEW OF THE REAR OF THE TRAILER. WARNING! THE OPERATOR IS REQUIRED

More information

DIGITAL BATTERY TORQUE WRENCH (BC-RAD SELECT) USER GUIDE

DIGITAL BATTERY TORQUE WRENCH (BC-RAD SELECT) USER GUIDE DIGITAL BATTERY TORQUE WRENCH (BC-RAD SELECT) USER GUIDE W.CHRISTIE (INDUSTRIAL) LTD CHRISTIE HOUSE, MEADOWBANK ROAD, ROTHERHAM, SOUTH YORKSHIRE, S61 2NF, UK T: +44(0)1709 550088 F: +44(0)1709 550030 E:

More information

USERS MANUAL MCD REMOTE OPERATOR

USERS MANUAL MCD REMOTE OPERATOR USERS MANUAL MCD REMOTE OPERATOR Order Code: 175G9004, 175G3061 Contents Contents Introduction...2 Important User Information...2 General Description...2 Symbols Used in this Manual...2 Installation...3

More information

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

INSTALLATION INSTRUCTIONS AND OPERATION MANUAL INSTALLATION INSTRUCTIONS AND OPERATION MANUAL NEMA 4X UL325-2010 Compliant Commercial and Industrial Door Operator Logic Control Continuous Duty IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the

More information

24V 3A EN54 Ancillary Power Supply

24V 3A EN54 Ancillary Power Supply 24V 3A EN54 Ancillary Power Supply Normal supply - green light on Fault condition - call Engineer Control relay - activated 3A Power Supply C-TEC Manufactured in England by C-Tec EN 54-4 : 1997 INSTALLATION

More information

CAUTION-ELECTRICALLY OPERATED PRODUCT

CAUTION-ELECTRICALLY OPERATED PRODUCT CAUTION-ELECTRICALLY OPERATED PRODUCT NOT RECOMMENDED FOR CHILDREN UNDER 14 YEARS OF AGE. AS WITH ALL ELECTRIC PRODUCTS, PRECAUTIONS SHOULD BE OBSERVED DURING HANDLING AND USE TO PREVENT ELECTRIC SHOCK.

More information

Electronic Products ELECTRONIC MAINTENANCE

Electronic Products ELECTRONIC MAINTENANCE SubDrive2W, 75, 100, 150, 300, MonoDrive, and MonoDrive XT Should an application or system problem occur, built-in diagnostics will protect the system. The FAULT light or digital display on the front of

More information

DLRM DLRM

DLRM DLRM Table of Contents 1. Before You Begin.........................................................Page 1 2. Installation Tips..........................................................Page 2 3. Mounting Components

More information