Studio Makeup Station International 30-inch Model International 36-inch Model

Transcription

1 International Installation and Owner s Manual Studio Makeup Station International 30-inch Model International 36-inch Model 5-light 30-inch Studio Makeup Station CONTENTS 8-light 30-inch Studio Makeup Station Important User Information General Manufacturer Installation Intended Use Electrical Rating Warranty Safety Installation General Maintenance User Instructions Description Lighting Electric Receptacle Mirror Counter Storage Shelf Tackboard (36-inch Model Only) Accessories Required Tools Fasteners and Parts List Parts List Fasteners light 36-inch Studio Makeup Station 9-light 36-inch Studio Makeup Station Installation Before Starting the Assembly Lighting Layout the Space Install the Mounting Bracket Install the First Makeup Station Install Additional Makeup Stations Complete the Installation Attach the Mirror Attach the Counter Electrical Installation Connect the Electrical Source Wiring Diagram 30-inch Model Wiring Diagram 36-inch Model Maintenance Broken Mirror Replacement Lighting Cleaning Replacement Parts Makeup Station Main Assembly Makeup Station Additional Parts Note: Note: Note: Note: Please read and understand the Studio Makeup Station Installation and Owner s Manual before assembly or installation. If you need additional information about your Studio Makeup Station, contact the Wenger Corporation using the information below. Two people must work together for some assembly steps. Because wall construction varies, wall anchors are not supplied with the Studio Makeup Station. Wenger Corporation 2005 Printed in USA 10/05 Part #187A Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota Questions? Call...USA:

2 IMPORTANT USER INFORMATION GENERAL Copyright 2005 by Wenger Corporation All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser's personal use. Printed and bound in the United States of America. The information in this manual is subject to change without notice and does not represent a commitment on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may appear in this manual. In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this manual. The information in this document is not intended to cover all possible conditions and situations that might occur. The end user must exercise caution and common sense when assembling or installing Wenger Corporation products. If any questions or problems arise, call Wenger Corporation at MANUFACTURER The Studio Makeup Station is manufactured by: Wenger Corporation 555 Park Drive Owatonna, MN INSTALLATION The Wenger Studio Makeup Station installation must comply with local regulations and codes. All personnel (including all temporary workers) installing the Wenger Studio Makeup Station must read and understand this entire manual. Personnel installing the Wenger Studio Makeup Station must comply with the warnings and cautions in the Safety Section. Always refer to the Electrical Installation information when connecting the Studio Makeup Station to a power source. INTENDED USE The Wenger Studio Makeup Station is intended for indoor use in normal ambient temperature and humidity conditions it must not be exposed to outside weather conditions. The Wenger Studio Makeup Station is intended to be permanently installed only as described in this manual. NOTE: If you decide to contact Wenger Corporation about your Studio Makeup Station, you may need to find the date of manufacture which is engraved on the steel frame below the Counter. 2

3 IMPORTANT USER INFORMATION CONTINUED ELECTRICAL RATING The Studio Makeup Station outlet ratings are: Standard Lamp Load Outlet Rating W01 German Standard 5-light: 1.25 Ampere 6-light: 1.5 Ampere 8-light: 2.0 Ampere 9-light: 2.25 Ampere 16 Ampere (Max) 250 VAC W02 Japan Standard 5-light: 2.5 Ampere 6-light: 3.0 Ampere 8-light: 4.0 Ampere 9-light: 4.5 Ampere 15 Ampere (Max) 125 VAC W03 British Standard 5-light: 1.25 Ampere 6-light: 1.5 Ampere 8-light: 2.0 Ampere 9-light: 2.25 Ampere 13 Ampere (Max) 250 VAC W04 Chinese Standard 5-light: 1.25 Ampere 6-light: 1.5 Ampere 8-light: 2.0 Ampere 9-light: 2.25 Ampere 10 Ampere (Max) 250 VAC W05 French Standard (Socket) German Standard (Plug) 5-light: 1.25 Ampere 6-light: 1.5 Ampere 8-light: 2.0 Ampere 9-light: 2.25 Ampere 16 Ampere (Max) 250 VAC W06 Australian Standard New Zealand Standard 5-light: 1.25 Ampere 6-light: 1.5 Ampere 8-light: 2.0 Ampere 9-light: 2.25 Ampere 10 Ampere (Max) 250 VAC W07 Swiss Standard 5-light: 1.25 Ampere 6-light: 1.5 Ampere 8-light: 2.0 Ampere 9-light: 2.25 Ampere 10 Ampere (Max) 250 VAC 3

4 WARRANTY The Studio Makeup Station is guaranteed free of defects in materials and workmanship for five full years. Our guarantee assures you of either a full refund or repair or replacement of the defective materials or workmanship without charge, at the discretion of our Customer Service Department. Just call a Customer Service Representative at or fax and state the reason you are dissatisfied. If a product return is necessary, your representative will issue a return authorization. This is your sole remedy for breach of this warranty. Should you have a question or problem with any Wenger product, don t hesitate to call, even if the product is past warranty. It s important to us that all our customers be satisfied. This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including the warranties of merchantability and fitness for a particular purpose, as well as all liability for incidental, consequential, special, and indirect damage. Wenger liability for direct damages shall be limited to the amount you paid for the product involved. Wenger reserves the right to make product changes without obligation to incorporate such changes into products previously sold. Some countries do not allow the exclusion or limitation of damages or warranties, so the above may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from one legal authority to another legal authority. 4

5 SAFETY Throughout this manual you will find WARNINGS and CAUTIONS which are defined as follows. WARNING means that failure to follow the instruction may result in serious injury or death. CAUTION means that failure to follow the instruction may result in injury or damage to property. Read and understand the following Safety Instructions before installing or using the Studio Makeup Station. Failure to observe these instructions can result in damage to property, serious injury or death! INSTALLATION! WARNING Do not connect the Makeup Station to an electrical source until the installation is complete and the mirror and counter are in place.! WARNING The Makeup Station must be permanently connected to a grounded wiring system.! WARNING Branch circuits must always be designed by an electrical engineer and comply with local electrical regulations and user requirements. Make sure that anyone Installing the Studio Makeup Station has read and understands this manual. The 36-inch Studio Makeup Station weighs about 80 lbs (37 kg) and the 30-inch Studio Makeup Station weighs about 72 lbs (33 kg) when completely assembled. Serious injury or damage to the Station can happen if only one person attempts to move or lift the Station. Two people must always work together when lifting or moving the Studio Makeup Station. Always wear safety glasses and safety shoes when installing the Makeup Station or when replacing any broken glass. Never lift the assembled Makeup Station by grasping the wire cages or the Shelf. Damage to the wire cages can occur. Always lift or move the Station by grasping the steel frame or the mirror surround. 5

6 SAFETY CONTINUED GENERAL! WARNING Never pour, spray or splash liquids onto the lighting or onto the Mirror Surround.! WARNING Never insert any object into the lampholders other than the recommended bulbs. Always observe and comply with the Warnings and Cautions posted on the system equipment. Always use the Makeup Station only for its intended purpose as described in these instructions. Always use only 60 watt or smaller incandescent bulbs or 15 watt swirl fluorescent bulbs. Never hang anything near the light bulbs or from the light bulb cages. Never plug appliances into the Makeup Station electrical outlets that will exceed the current capacity of the circuit. Never leave appliances plugged into the Makeup Station operating and unattended. Never sit or stand on the Makeup Station counter. MAINTENANCE Never place items heavier than 75 lbs (35 kg) onto the Makeup Station Counter. Never place items heavier than 25 lbs (12 kg) onto the Makeup Station Shelf. Always provide adult supervision when children use the Makeup Station.! WARNING Do not alter the electrical circuits without the expressed permission of Wenger Corporation.! WARNING Replace any malfunctioning electrical components only with components with the same specification. Replace any broken light bulbs immediately. Always turn the light switch off before changing bulbs. Always disconnect power to the Makeup Station before cleaning. Replace the Mirror immediately if it is cracked or broken. 6

7 USER INSTRUCTIONS DESCRIPTION The Studio Makeup Station is intended to provide the necessary elements to apply makeup or create special visual effects. It has the following features. 1. Lighting that is bright and untainted in color. 2. An electrical outlet for makeup appliances. 3. A large mirror. 4. A storage shelf that also is a light diffuser. 5. A counter with ample elbow room and a light-diffusing surface. 6. A tackboard (36-inch Models only) for makeup design renderings, schedules, etc. Shelf Lights Tackboard Electrical Outlet Mirror 9-light Studio Makeup Station Counter The Studio Makeup Station can be installed as a single unit or in a row of two or more Stations. Each Station, whether a single unit or a row, has the features outlined above. The Makeup Station on the right is always a 9- light or 8-light Station. All others in a row are 6-light or 5-light Stations. 6-light or 5-light Studio Makeup Station 9-light or 8-light Studio Makeup Station 7

8 USER INSTRUCTIONS CONTINUED LIGHTING Light bulbs are not supplied with the Studio Makeup Station. The end user should choose the light bulb that is best suited for the Makeup Station use. For accurate color rendering, Wenger Corporation recommends either of the following. GE Reveal 60 watt or GE Reveal 40 watt incandescent bulbs or equivalent. Full-spectrum, 15-watt, swirl fluorescent bulbs. Always use only 60 watt or smaller incandescent bulbs or 15 watt swirl fluorescent bulbs. Never hang anything near the light bulbs or from the light bulb cages. NOTE: Studio Makeup Stations manufactured for 125 VAC power sources (W02 - Japan Standard) require bulbs with E26 bases. Stations with 250 VAC power sources require bulbs with E27 bases. Configurations Each 5-light Studio Makeup Station has five lights, three on the left and two on the top. The Light Switch on the lower left of the Mirror turns the lights on and off. Each 8-light Studio Makeup Station has eight lights, three on the right, two on the top and three on the left side. The Light Switch on the lower left of the Mirror turns the lights on and off. Each 6-light Studio Makeup Station has six lights, three on the left and three on the top. The Light Switch on the lower left of the Mirror turns the lights on and off. Each 9-light Studio Makeup Station has nine lights, three on the right, three on the top and three on the left side. The Light Switch on the lower left of the Mirror turns the lights on and off. NOTE: When a 9-light Station and a 6-light Station are adjacent to each other, they share the 9-light Station left column of lights. Electrical Outlet and Light Switch 5-light 30-inch Studio Makeup Station 8-light 30-inch Studio Makeup Station 6-light 36-inch Studio Makeup Station 9-light 36-inch Studio Makeup Station 8

9 USER INSTRUCTIONS CONTINUED LIGHTING CONTINUED Refer to the illustration below describing the light switch function. This column of light is common to both Stations and is controlled by the Station to the right. If this Station is used, it is necessary to turn on the lights for this Station and the Station immediately to the right. ELECTRIC RECEPTACLE An electrical receptacle is located on the lower left of the Mirror on each Makeup Station. Additional appliances can plug into this receptacle.! WARNING Never pour, spray or splash liquids onto the lighting or onto the Mirror Surround. Never plug a device with faulty wiring into the Makeup Station electrical outlets. Never plug appliances into the Makeup Station electrical outlets that will exceed the current capacity of the circuit. Rocker Switch Typical Receptacle (W06 - Australian/New Zealand Standard Receptacle is shown) 9

10 USER INSTRUCTIONS CONTINUED MIRROR The Studio Makeup Station Mirror is shatter-resistant and shatter-controlled. It is not unbreakable. Never strike the mirror. Never han le broken mirror with bare hands. Use Caution when replacing a broken mirror. NOTE: Refer to page 28 for instructions regarding replacing a broken mirror or call Wenger Corporation Customer Service. COUNTER The Counter surface is matte white for light diffusion and is mar and stain resistant. The surface can withstand the operating temperatures typical of the dressing room environment. Refer to the Maintenance Section on page 27 regarding cleaning the Counter surface. The Counter will support loads up to 75 lbs (34 kg). Never sit or stand on the Makeup Station counter. Never place items heavier than 75 lbs (35 kg) onto the Makeup Station Counter. Never place items or materials directly on the Counter surface tht could scratch, burn or cause damage to the surface. STORAGE SHELF The Shelf is suitable for storage of wigs, hats, makeup kits, etc. The Shelf surface is matte white for light diffusion and is mar and stain resistant. The surface can withstand the operating temperatures typical of the dressing room environment. The Shelf will support loads up to 25 lbs (12 kg). Refer to the Maintenance Section on page 27 regarding cleaning the Shelf surface. Never place items heavier than 25 lbs (12 kg) onto the Makeup Station Shelf. Never place items or materials directly on the Counter surface tht could scratch, burn or cause damage to the surface. Always use only 60 watt or smaller incandescent bulbs or 15 watt swirl fluorescent bulbs. 10

11 USER INSTRUCTIONS CONTINUED TACKBOARD (36-INCH MODEL ONLY) The Tackboard is shipped separately with each the 36-inch Model Studio Makeup Station. The Tackboard may be applied to the Mirror surface on either side, top or bottom. Wenger Corporation recommends installation at the side of the Mirror. To install the Tackboard, do as follows. 1. Remove the Tackboard from its package. Do not remove the protective backing from the mounting tape at this time. 2. Decide where the Tackboard will be mounted. 3. Remove the protective backing from the mounting tape. 4. Carefully position the Tackboard on the Mirror surface and press firmly. Don t let the exposed tape touch the Mirror until the Tackboard is in the desired position. Do not pound on the Tackboard. Breakage of the mirror can occur. Tackboard shown on the right side of the Mirror. ACCESSORIES The following accessories are only available for the 36-inch Model Studio Makeup Station. Storage Cubby an open Cubby attaches below the Counter on the right hand side. The storage volume is 8-inches wide, 7-inches high, and 15-inches deep (20.3 cm x 17.7 cm x 38.1 cm). Drawer Unit a closed drawer (not equipped with a lock) attaches below the Counter on the right hand side. It has drawer glides for smooth operation and a storage volume similar to the Storage Cubby described above. Contact Wenger Corporation for specific dimensions, installation procedures and pricing information. REQUIRED TOOLS Tools required for installation are a cordless drill, a phillips screwdriver or a phillips insert bit, a 3/8" hex nut driver, a 9/16" open end wrench, a box level, an electronic scanner to locate wall studs, a tape rule, pencil, and bits and drivers for wall anchor hardware (supplied by end user). Phillips Insert Bit 9/16-inch Open End Wrench 3/8-inch Hex Nut Driver Insert Phillips Screwdriver Cordless Drill Box Level Tape Rule Electronic Scanner Lead Pencil 11

12 FASTENERS AND PARTS LIST The Makeup Station is shipped with all components in a single box, the main assembly, a corrugated sleeve containing the Mirror, a hardware bag, the Counter under the main assembly, the Tackboard Assembly (36-inch Model only) in a corrugated sleeve, and the Wall Mounting Bracket. FASTENERS 3/4" 3/4" (1) Self-drill Screw, 1/4-14x3/4" (2) Hex Flange Nut, 3/8-16 (3) Phillips Head Sheet Metal Screw, 10x3/4" PARTS LIST Item Qty. Description Item Qty. Description 1 2* Self-drill Screw, 1/4-14x3/4-inch 6 2 Bottom Frame Clips 2 4* Hex Flange Nut, 3/ Wall Mounting Bracket 3 4* Phillips Head Sheet Metal Screw, 10x3/4-inch 8 1 Counter 4 1* Owner s and Installation Manual (including Wiring Diagram) 9 1** Tackboard Assembly 5 1 Studio Makeup Station Assembly 10 1 Hardware Bag * Contained in Hardware Bag ** 36-inch Model Only NOTE: 9-light Studio Makeup Station Assembly is shown. 12

13 INSTALLATION BEFORE STARTING THE ASSEMBLY Before installing the Studio Makeup Station, do the following. 1. Read and understand this installation instruction completely. 2. Open all cartons and make sure each includes a Studio Makeup Station, a hardware bag, the Wall Mounting Bracket, a Tackboard (36-inch Model only), a Mirror (packaged in a corrugated sleeve) and a Counter. NOTE: The Counter and carton containing the Mirror are packaged under the Makeup Station. NOTE: Wall anchors are not supplied because wall constructions vary. Before starting the installation of the Studio Makeup Station, obtain the required wall anchors. 3. Inventory the hardware package and make sure that all required hardware is present. 4. The room where the Makeup Stations will be installed must be permanently wired with a suitable electrical source. a. Each 9-light Station (lighting using 540 watts) or 8-light Station (lighting using 480 watts) can have external appliances plugged into the receptacle that can draw high current loads. Make sure that the electrical supply is capable of supplying sufficient current and has adequate overload protection. b. Always consult local electrical codes before starting the installation. Mirror Surround Do not use the Wire Cages to lift the Makeup Station. Shelf Wire Cage Steel Frame Mirror NOTE: 9-light Studio Makeup Station Assembly is shown.! WARNING Do not connect the Makeup Station to an electrical source until the installation is complete and the mirror and counter are in place.! WARNING A licensed electrician must do the electrical installation.! WARNING The studio electrical source must must be permanently wired and comply with local electrical codes. This must include a switch(s) that can disconnect the Studio Makeup Station outlet(s) and must include a pilot light outside the dressing room door to indicate that the outlet circuitry is energized. Make sure that anyone Installing the Studio Makeup Station has read and understands this manual. Always wear safety glasses and safety shoes when installing the Makeup Station or when replacing any broken glass. The 36-inch Studio Makeup Station weighs about 80 lbs (37 kg) and the 30-inch Studio Makeup Station weighs about 72 lbs (33 kg) when completely assembled. Serious injury or damage to the Station can happen if only one person attempts to move or lift the Station. Two people must always work together when lifting or moving the Studio Makeup Station. Never lift the assembled Makeup Station by grasping the wire cages or the Shelf. Damage to the wire cages can occur. Always lift or move the Station by grasping the steel frame or the mirror surround. 13

14 INSTALLATION CONTINUED LIGHTING Light bulbs are not supplied with the Studio Makeup Station. The end user should choose the light bulb that is best suited for the Makeup Station use. For accurate color rendering, Wenger Corporation recommends either of the following. GE Reveal 60 watt or GE Reveal 40 watt incandescent bulbs or equivalent. Full-spectrum, 15-watt, swirl fluorescent bulbs. Always use only 60 watt or smaller incandescent bulbs or 15 watt swirl fluorescent bulbs. NOTE: Studio Makeup Stations manufactured for 125 VAC power sources (W02 - Japan Standard) require bulbs with E26 bases. Stations with 250 VAC power sources require bulbs with E27 bases. LAYOUT THE SPACE Never hang anything near the light bulbs or from the light bulb cages. NOTE: Refer to the illustration on the opposite page (page 15) which includes equivalent metric dimensions. 1. Before starting the installation, decide where the Studio Makeup Stations will be installed. 3. Draw a vertical line on the wall that will locate the vertical centerline of the left (or right) Station. a. Make sure that the line is vertical to the floor. b. The centerline cannot be closer than 20-1/2-inches (52 cm) on the 36-inch Model or 17-1/2-inches (44.5 cm) on the 30-inch Model from an obstruction on either side (such as a wall, I-beam, cabinet, etc.). c. If more than one Studio Makeup Station is being installed, measure 36-inches (91.5 cm) 30-inches (76.2 cm), depending upon the Model, from the centerline and draw another vertical line for the centerline of the second Station. d. Draw additional centerlines for any additional Stations that will be installed. e. Draw a horizontal line 57-1/2-inches (146 cm) from the floor across the centerlines. Make sure that the line is level. This line locates the top edge of the Mounting Bracket. The 36-inch Model is 23-1/2-inches (59.7 cm) wide and the 30-inch Model is 17-1/2-inches (44.5 cm). NOTE: Placing the top edge of the Mounting Bracket at 57-1/2-inches (146 cm) from the floor will locate the top surface of the Counter at 29-inches (73.7 cm) from the floor and the top of the Shelf at 68-1/2-inches (174 cm) from the floor. If the Counter top surface must be higher or lower, adjust the Mounting Bracket Position by moving it upward or downward. 4. Using an electronic scanner, locate and mark each stud in the wall that will be used for the installation with a vertical line that passes through the horizontal line that locates the top edge of the Mounting Bracket. NOTE: Sometimes the 30-inch Model Mounting Bracket does not cross a wall stud. If the Mounting Bracket cannot be attached to a wall stud, refer to the instructions for wall anchors in the section Install the Mounting Bracket on page

15 INSTALLATION CONTINUED LAYOUT THE SPACE CONTINUED * 17-1/2" for 30-inch Model (44.45 cm) ** 30" for 30-inch Model (76.20 cm) Corner 20-1/2" Minimum Distance to a Wall (52.07 cm)* 36"** (91.44 cm) Top Edge of Mounting Bracket Top Surface of Shelf 36"** (91.44 cm) Station Mounting Area 36"** (91.44 cm) Centerline of each Station Top of Shelf 68-1/2" ( cm) 6-light Makeup Station 29" (73.66 cm) 9-light Makeup Station Floor Top Surface of Counter 57-1/2" cm) 36-inch Model Layout Shown 15

16 INSTALLATION CONTINUED INSTALL THE MOUNTING BRACKET 1. Remove the Mounting Bracket from the shipping box. 2. Locate the Hardware Bag and set it aside. 3. Align the Mounting Bracket to the wall with the top edge of the Mounting Bracket on the Horizontal LIne and the centerline of the Mounting Bracket (user must mark the Bracket centerline with chalk) aligned to the Station Centerline on the wall as shown below. 3 Horizontal Line for Top Edge of Mounting Bracket Position of Studs Mounting Bracket Mounting Bracket Centerline Mark the Bracket centerline with caulk on the top surface of the Bracket. 4. For walls with wood stud construction, use the following instructions. For metal stud or masonry wall construction, skip to step 5. a. Hold the Mounting Bracket in place and note the position of the studs. b. If the Mounting Bracket crosses two studs, attach the Bracket with four 1/4x3-inch (6 mm x 8 cm) Hex Head Lag Screws (supplied by end user), two in each stud. c. If the Mounting Bracket crosses one stud, attach the Bracket with two 1/4x3-inch (6 mm x 8 cm) Hex Head Lag Screws (supplied by end user) to the stud and then attach the Bracket to the wall with four heavy duty drywall anchors (consult a local hardware supplier). d. If the Mounting Bracket does not cross any studs, attach the Bracket to the wall with eight heavy duty drywall anchors (consult a local hardware supplier) as shown below. Make sure that the four outside anchors are installed outside the Mounting Bracket Studs. Station Centerline 4b Bracket crosses two studs. Hex Head Lag Screw Mounting Bracket Centerline! WARNING Always wear safety glasses and safety shoes when installing the Studio Makeup Station to avoid serious injury. Position of Studs 4c Bracket crosses one stud. Hex Head Lag Screw Position of Stud Mounting Bracket Centerline 4d Bracket does not cross a stud Mounting Bracket Heavy Duty Drywall Anchors, evenly spaced (supplied by end user). 16

17 INSTALLATION CONTINUED INSTALL THE MOUNTING BRACKET CONTINUED 5. For walls with metal stud construction do as follows. a. Hold the Mounting Bracket in place and note the position of the studs. b. If the Mounting Bracket crosses two studs, attach the Bracket with four 14x2-inch (6 mm x 6 cm) Self-drilling Screws (supplied by end user), two in each stud. c. If the Mounting Bracket crosses one stud, attach the Bracket with two 14x2-inch (6 mm x 6 cm) Self-drilling Screws (supplied by end user) to the stud and then attach four heavy duty drywall anchors (consult a local hardware supplier) to the wall. d. If the Mounting Bracket does not cross any studs, attach the Bracket to the wall with eight heavy duty drywall anchors (consult a local hardware supplier) as shown below. Make sure that the four outside anchors are installed outside the Mounting Bracket Studs. 6. For masonry walls, use at least two 1/4-inch (6 mm) masonry anchors that are appropriate for the wall construction (consult a hardware supplier). 7. Repeat this procedure for all Station Mounting Brackets. NOTE: Install all Mounting Brackets before hanging any Studio Stations. 5b Bracket crosses two studs. Position of Studs 5c Bracket crosses one stud. Position of Studs Self-drilling Screw Mounting Bracket Centerline Self-drilling Screw 5d Bracket does not cross a stud Mounting Bracket Stud Heavy Duty Drywall Anchors, evenly spaced (supplied by end user). 17

18 INSTALLATION CONTINUED INSTALL THE FIRST MAKEUP STATION 1. Remove the four Flange Nuts, 3/8-16, from the hardware bag. 2. Screw (clockwise) a Flange Nut, 3/8-16, onto each each of the two Mounting Bracket Studs with the Flanges facing upward as shown below. Position the Flange Nuts so that the flange of the nut is one-half inch from the top edge of the Mounting Bracket. Mounting Bracket Stud Flange Nut, 3/8-16 Flange facing upward and 1/2-inch (1.3 cm) from the top of the Mounting Bracket. Mounting Bracket Stud Flange Nut, 3/8-16 Mounting Bracket Mounting Bracket 1/2-inch (1.3 cm) NOTE: When installing two or more Makeup Stations, always first install a 6-light or 5-light unit on the left end. Add additional 6-light or 5-light units to the right and finish the row with a 9-light or 8- light unit on the right end. 3. Find the shipping container marked 6-light unit or 5-light unit. a. With two people working together, place the shipping container onto a flat surface near the installation wall. b. Remove the container cover and fold the sides down. The 36-inch Studio Makeup Station weighs about 80 lbs (37 kg) and the 30-inch Studio Makeup Station weighs about 72 lbs (33 kg) when completely assembled. Serious injury or damage to the Station can happen if only one person attempts to move or lift the Station. Two people must always work together when lifting or moving the Studio Makeup Station. Container Cover 6-light or 5-light Makeup Station The Counter and the Mirror Carton are packaged under the Makeup Station. Shipping Container Sides 18

19 INSTALLATION CONTINUED INSTALL THE FIRST MAKEUP STATION CONTINUED 6. With two people working together, tilt the Makeup Station into an upright position. a. Only handle the Makeup Station by grasping the Steel Frame do not lift or handle the Makeup Station by grasping the Light Cages or the Shelf. Note: Always start a row with a 6-light unit or a 5-light unit on the left end. Add additional 6-light or 5- light units to the right and finish the row with a 9-light unit or 8-light unit on the right end. Never lift the assembled Makeup Station by grasping the wire cages or the Shelf. Damage to the wire cages can occur. Always lift or move the Station by grasping the steel frame or the mirror surround. Never lift the Makeup Station by grasping the Makeup Station Shelf Never lift the Makeup Station by grasping the Makeup Station Wire Cages Wire Cage Makeup Station Frame Always lift by grasping the Makeup Station Frame Always install the 6-light Makeup Station first and on the left side. 6-light or 5-light Makeup Station 9-light or 8-light Makeup Station 19

20 INSTALLATION CONTINUED INSTALL THE FIRST MAKEUP STATION CONTINUED 7. Attach the 6-light or 5-light Makeup Station to the left-hand Mounting Bracket as follows. a. With two people working together, grasp the Makeup Station Frame and lift the Station upward. b. Place the Frame onto the Mounting Bracket Studs by engaging the Studs with the Frame Upper Bracket Slots. Allow the Makeup Station to rest on the two Flange Nuts on the Mounting Bracket Studs. c. Screw a Flange Nut with the Flange facing downward onto the top of each Mounting Bracket Stud by hand. Leave the Flange Nut loose for later adjustment. NOTE: If the Mounting Bracket Studs do not align to the Frame Upper Bracket Slots, loosen the screws that attach the Mounting Bracket to the wall. After placing the Frame onto the Mounting Bracket Studs, tighten the screws that attach the Mounting Bracket to the wall.! WARNING Avoid pinching fingers between the Station and the wall or bracket when engaging the mounting bracket studs. Mounting Bracket 6-light or 5-light Makeup Station 7a-b Frame Upper Bracket Mounting Bracket Stud Frame Upper Bracket Slot Flange Nut, 3/8-16 REAR VIEW (FROM WALL) Mounting Bracket FRONT VIEW 7c Flange Nut, 3/8-16 REAR VIEW (FROM WALL) 20

21 INSTALLATION CONTINUED INSTALL THE FIRST MAKEUP STATION CONTINUED 8. Level the Makeup Station as follows. a. Place a Box Level across the two Counter Mounting Brackets. b. To move the left side upward, use a 9/16-inch open end wrench and turn the Left Lower Flange Nut counterclockwise and the Right Lower Flange Nut clockwise. Turning each nut one-half turn will lift the left edge 1/16-inch (1.58 mm). NOTE: Always turn one nut clockwise and one nut counterclockwise the same amount to keep the Makeup Station in the same relative position. This is important when leveling a group of Makeup Stations. c. To lower the left side, turn the Left Lower Flange Nut clockwise and the Right Lower Flange Nut counterclockwise. d. When the Counter Mounting Brackets are level, tighten the two Upper Flange Nuts with a 9/16-inch open end wrench. Upper Flange Nut Left Lower Flange Nut Mounting Bracket Right Lower Flange Nut Counter Mounting Brackets Box Level 21

22 INSTALLATION CONTINUED INSTALL ADDITIONAL MAKEUP STATIONS NOTE: Always start a row with a 6-light or 5-light unit on the left end. Add additional 6-light units to the right and finish the row with a 9-light unit or a 8-light unit on the right end. 1. Find a shipping container with the next required unit. a. With two people working together, place the shipping container onto a flat surface near the installation wall. b. Remove the cover and fold the sides down. 2. Place the Makeup Station onto the Mounting Bracket next to the 9-light or 8-light Makeup Station. 3. Level the Makeup Station making sure that the Counter Mounting Brackets are even and tighten the Upper Flange Nuts. 4. Install any additional Makeup Stations in the same way. COMPLETE THE INSTALLATION 1. Fasten the bottom of the Makeup Station Frame to the wall with Bottom Frame Clips as follows. a. Hold a Bottom Frame Clip against the Frame and mark the lower hole location for the Wall Makeup Station Frame Anchor with a pencil. Bottom Frame Clip Pencil b. Install a medium duty wall anchor (supplied by the end user consult a local hardware supplier) at the mark on the wall. Mark wall anchor location Medium Duty Wall Anchor c. Attach a Bottom Frame Clip to the Frame with a #14 Self-drilling Screw (from the hardware bag) and fasten the Clip to the wall with the wall anchor screw. Bottom Frame Clip #14 Selfdrilling Screw 2. Continue installing the Bottom Frame Clips to all of the Makeup Stations. 22

23 INSTALLATION CONTINUED ATTACH THE MIRROR 1. Remove the Mirror from the shipping carton and inspect for damage. 2. With two people working together, place the Mirror against the Frame about an inch (2 cm) from the top with Mirror Flange at the bottom. 3. Slide the Mirror upward until the Mirror Flange contacts the Frame and the top clips engage the Frame. 4. With one person holding the Mirror in place, attach the two Pan Head Screws (included with the Mirror in the sleeve) that hold the Mirror to the Frame. Never strike the mirror. Never hanlde the mirror with bare hands. Tighten the Pan Head Screws only enough to be snug. Over tightening will strip the threads in the Frame. Shelf Bottom Surface Slide the Mirror upward until the top clips engage the flange on the Frame. Mirror Pan Head Screw Pan Head Screw ATTACH THE COUNTER 1. Assemble the Counter to the Makeup Station. a. Remove the Counter from the carton and locate the four Pan Head Screws in the Hardware Bag. NOTE: If there is a strap or tape attaching the flexible conduit to the Counter Support Bracket, remove the strap or tape before placing the Counter onto the Counter Support Brackets. b. Place the Counter onto the Counter Support Brackets and slide it into place. c. It may be necessary to lift the curved edge of the Counter slightly upward to fit it into the space in the Frame. d. Attach the Counter to the Counter Support Brackets with the four Pan Head Screws. Tighten the Pan Head Screws only enough to be snug. Over tightening will strip the threads in the Counter. Counter Support Brackets Pan Head Screw Counter Bottom Surface 23

24 ELECTRICAL INSTALLATION CONNECT THE ELECTRICAL SOURCE! WARNING To reduce the risk of burns, fire, electric shock or injury to persons, observe the following: Never connect the electrical source until all of the Makeup Stations are completely assembled with Mirrors and Counters in place. Never connect the Makeup Stations to an inadequate electrical circuit. Always have an electrical engineer design or review the circuits to make sure that they comply with electrical codes and anticipated use. Always have a licensed electrician make any electrical connections. Never modify the wiring inside the Makeup Stations. Never allow anyone to use the Makeup Stations until all electrical work is complete and light bulbs are installed. NOTE: Make sure that the Electrical Receptacle on the lower left side of the Mirror is compatible with the end user s country standard. Notes to the Electrician: 1. Wenger Studio Makeup Stations are supplied with conductor leads inside of 24 to 30 inches (60 cm to 75 cm) of flexible armored conduit. This is connected to a 2 x4 x2 (5 cm x 10 cm x 5 cm) connection box, with a cover. The volume of the supplied connection box is 12.8 in 3 (210 cm 3 ). The boxes are intended for use in dry locations only. 2. On-site electrician(s) or electrical contractors are solely responsible for determining the best method for connecting individual stations to the power source branch circuits. Wenger Corporation recommends the use of dedicated individual circuits and terminal block connections that are housed within the supplied box. The on-site electrician must drill holes into the connection box for wall mounting and for the supply branch circuit conductors. 3. In a typical installation, the boxes are mounted to the wall below the Makeup Station desk. Dedicated source conductors are normally supplied directly through the wall or by means of a cable raceway mounted to the wall(s). If the quantity of Makeup Stations to be connected exceeds the number of available dedicated circuits, a qualified electrician should install a separate and dedicated supply panel or sub panel. 4. Wenger Corporation does not supply terminal blocks for connecting the Studio Makeup Stations to the supply branch circuits. Terminal blocks that are used should conform to EN or EN Wenger recommends the following: Terminal block connectors should accommodate conductors up to 4mm 2 (#12 AWG) Terminal blocks should be rated for a minimum voltage of 250 VAC. Terminals blocks should be rated for a minimum current capacity of 20 amps. 24

25 ELECTRICAL INSTALLATION CONTINUED CONNECT THE ELECTRICAL SOURCE CONTINUED Input 250 Volts Typical (125 Volts Japan Standard) Box for Connection Cover Flexible Metal Conduit Terminal Block (Not Included) See NOTE Below Terminal Block is NOT PROVIDED by Wenger. Minimum Wire Area Capacity: 4 mm 2 (#12 AWG) Minimum Current Capacity: 20 amps Minimum Voltage Capacity: 250 VAC Studio Makeup Station Yellow/Green, 14 AWG Light Blue, 14 AWG Brown, 18 AWG Brown, 14 AWG 250 Volts (125 Volts Japan Standard) 25

26 ELECTRICAL INSTALLATION CONTINUED WIRING DIAGRAM 30-INCH MODEL Surround 60 or 40 Watt E26 or E27 Lampholder Brown, 18 AWG Lt Blue, 18 AWG Brown, 18 AWG Lt Blue, 18 AWG Ground Brown, 18 AWG Lt Blue, 18 AWG Brown, 18 AWG Lt Blue, 18 AWG Green/Yellow, 18 AWG Switch Insert Outlet Insert Note: Right-hand lights are not present on Five-light Models. Lt Blue, 14 AWG Brown, 14 AWG Green/Yellow, 14 AWG Brown, 18 AWG To Supply Branch Circuit Key Lt Blue = N Green/Yellow = Ground Brown = L1 26

27 ELECTRICAL INSTALLATION CONTINUED WIRING DIAGRAM 36-INCH MODEL Surround 60 or 40 Watt E26 or E27 Lampholder Brown, 18 AWG Lt Blue, 18 AWG Brown, 18 AWG Lt Blue, 18 AWG Ground Brown, 18 AWG Lt Blue, 18 AWG Brown, 18 AWG Lt Blue, 18 AWG Green/Yellow, 18 AWG Switch Insert Outlet Insert Note: Right-hand lights are not present on Five-light Models. Lt Blue, 14 AWG Brown, 14 AWG Green/Yellow, 14 AWG Brown, 18 AWG To Supply Branch Circuit Key Lt Blue = N Green/Yellow = Ground Brown = L1 27

28 MAINTENANCE BROKEN MIRROR REPLACEMENT To reduce the risk of damage and injury to persons, observe the following: Wear safety glasses and safety shoes. Dispose of broken mirror in a safe manner. Never handle the mirror with bare hands. Two people must work together to avoid injury or damage to the mirror. Do not remove the Counter. Removing the Counter exposes electrical wires. Never strike the mirror. To replace a damaged Mirror, do the following. 1. Remove the broken mirror as follows. a. With one person (wearing work gloves) holding the Mirror in place and a second person using a short phillips screwdriver, remove the two pan head screws that hold the mirror in place. Set the screws aside. b. Using work gloves, slide the broken mirror downward about one inch and then lift the mirror away from the Station and set it aside. Shelf Bottom Surface Do not remove the Counter. Slide the Mirror downward until the top clips disengage the flange on the Frame. Pan Head Screw Mirror Pan Head Screw 28

29 MAINTENANCE CONTINUED MIRROR REPLACEMENT CONTINUED 2. Install the new Mirror as follows. a. Remove the new Mirror from the shipping carton and inspect for damage. b. With two people working together, place the Mirror against the Frame about an inch (2 cm) from the top with Mirror Flange at the bottom. c. Slide the Mirror upward until the Mirror Flange contacts the Frame and the top clips engage the Frame. d. With one person holding the Mirror in place, attach the two Pan Head Screws (set aside when the broken Mirror was removed from the Frame) that hold the Mirror to the Frame. Tighten the Pan Head Screws only enough to be snug. Over tightening will strip the threads in the Frame. Slide the Mirror upward until the top clips engage the flange on the Frame. Pan Head Screw Shelf Bottom Surface Mirror Do not remove the Counter. Pan Head Screw LIGHTING For accurate color rendering, Wenger recommends either of the following replacement bulbs. GE Reveal 60 watt or GE Reveal 40 watt incandescent bulbs or equivalent. Full-spectrum, 15-watt, swirl fluorescent bulbs. Always use only 60 watt or smaller incandescent bulbs or 15 watt swirl fluorescent bulbs. Never hang anything near the light bulbs or from the light bulb cages. Always turn the light switch off before replacing bulbs. Always wear gloves when removing a broken bulb. NOTE: Studio Makeup Stations manufactured for 125 VAC power sources (W02 - Japan Standard) require bulbs with E26 bases. Stations with 250 VAC power sources require bulbs with E27 bases. CLEANING 1. Use a soft cotton cloth and a mild detergent to clean the Counter and Shelf. 2. Avoid using harsh, abrasive detergents on the Counter and Shelf. Difficult stains can be removed with a non-abrasive bathtub cleaner. 3. Clean the Mirror with a clean soft cotton cloth and a glass cleaner. 4. To clean residue or dust from bulbs, do as follows. a. Turn the lights off and allow the bulbs to cool. b. Carefully remove the bulbs from the sockets. c. Clean the bulbs with a dampened cloth. d. Reinstall the bulbs.! WARNING Never pour, spray or splash liquids onto the lighting or onto the Mirror Surround. 29

30 REPLACEMENT PARTS MAKEUP STATION MAIN ASSEMBLY 11 NOTE: W06 - Australian/New Zealand Standard Receptacle is shown Item Description Item Description 1* Mirror Surround Assembly, Studio 10* Shelf, Studio 2* Mirror Assembly, Studio 11 3/8" Screw-in Connector/ Flex Conduit 3 Side Raceway Cover, Studio 12 Phillips Oval Head Screw, 8-32x3/4" Grade 2, Wedgewood 4 (blank item) 13 Phillips Truss Head Screw, 6-32x1/2" Grade 2, White 5* Top Raceway Cover, Studio 14 Rocker Switch 6 Corner Cover, with logo 15 Lamp Holder, Snap-in 7 Corner Cover, Plain 16 Outlet** 8* Counter, Studio * Specify 9-light, 8-light, 6-light, or 5-light Model 9* Main Frame, Studio **Specify country 30

31 REPLACEMENT PARTS CONTINUED MAKEUP STATION ADDITIONAL PARTS Item Description 1* Wall Mounting Bracket 2 Tackboard Assembly (36-inch Model only) 3 Bottom Frame Clip 4 Self-drill Screw, 1/4-14x3/4" 5 Phillips Head Sheet Metal Screw, #10x3/4" 6 Flange Nut, 3/8-16 * Specify 36-inch or 30-inch Model 31