INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Ultra Short-Throw Projector Wall Mount Model: UNIU NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA USA USA and Canada Phone: Fax: Other Locations Phone: (001) Fax: (001) EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) Fax: +44 (0)

2 UNIU Table of Contents Weight Capacity 2 Warning Statements 2 Installation Tools 3 Parts List 3 Features 4 Determining the Installation Height 5 Wood Stud Installation 6 Attaching the Projector Arm 7 Throw Distance Calculation 8 Attaching the Projector Mount 9 Adjustable Mounting Bracket Installation 12 Utilizing the Storage Feature 13 Cable Management 14 Technical Specifications 15 Warranty 16 Disclaimer 16 Weight Capacity Maximum projector weight: Warning Statements 50 lb. THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE (5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THEN THE WALL STRUCTURE MUST BE REINFORCED. PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN- DERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS. SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY. At least two qualified people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the projector. If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is recommended. Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in wall. Cutting/drilling into an electrical line may cause serious injury. Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water damage to the mounting surface. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact Contact Premier Mounts with any questions (800) techsupport@mounts.com Page 2 Visit the Premier Mounts website at Installation Instructions

3 Installation Tools The following tools may be required depending upon your particular installation. They are not included. UNIU Phillips Screwdriver ¼ Drill Bit Electronic Stud Finder Level ½ Socket and Socket Wrench Drill Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) UNIU Hardware Wall Plate (Qty 1) Arm Assembly (Qty 1) End Cover (Qty 1) Adjustable Mounting Assembly - Pre-Assembled (Qty 1) Internal Slide Plate (Qty 1) Back Plate Covers (Qty 2) M4 x 10mm Security Screws for FTP Install (Qty 4) M6 x 12mm Security Screws for PDS Install (Qty 2) M5 x 8mm Security Screws (Qty 7) M6 x 16mm Security Screws (Qty 2) 5 16 x 3 Lag Bolts (Qty 4) M5 Allen Wrench (Qty 1) ¼ Nylon Spacer (Qty 2) Square Washers (Qty 4) Installation Instructions Visit the Premier Mounts website at Page 3

4 UNIU Features Premier Mounts universal ultra short-throw projector arm (UNIU) is one of the most flexible and installer-friendly shortthrow arms on the market. It allows throw distance adjustments from 6.5 to 18. To make installatins even easier, an array of mounting points at the top and bottom of the GearBox allows you to mount the UNIU off-center from the whiteboard/screen, if needed. The UNIU mounts to a single stud or dual studs at 16, 18 or 24 spacing, and are designed for use with the Fine-Tune Projector (FTP), PDS and SpiroLock projector mounts. Flexible Mounting Options Mounts to dual wood studs (16, 18 or 24 spacing) Cable Routing Discreetly manage signal and power cables through the arm and into the GearBox UNIU Universal Projector Capability Attach an FTP, PDS or SpiroLock universal projector mount to fit most short-throw projectors on the market. A/V Equipment Security Patent-pending GearBox for PC, Mac mini or control modules is secured with Lock-It security hardware Page 4 Visit the Premier Mounts website at Installation Instructions

5 Determining the Installation Height UNIU The UNIU is designed for use with the Fine-Tune Projector (FTP), PDS or SpiroLock projector mounts. In order to determine the installation height and throw distance, their projector mounting bracket must be mounted to the projector. Please refer to the projector mount installation instructions prior to performing the following steps. Refer to the projector s user s manual to determine the offset of the projector lens to the top of the screen/whiteboard (B). Projector Bracket Projector Lens Measure distance from center of lens to the top of the projector mounting bracket (C). Add the distance from the ground to the top of the screen (A). Add the projector manufacturers recommended offset from the projector manual (B), then add the measurement from Step 1 (C). Lastly, add 2.5 if you are using a PDS mount, 2.8 if SpiroLock or 3.8 if FTP. (Example: A + B + C or 2.8 or 3.8 =?) Mark +2.5"/+2.8"/+3.8" Top of Screen A - Legend Distance from ground to the top of the screen/whiteboard (viewable area). B - Manufacturers recommended offset measurement. This measurement will be listed in the Users Manual. C - Center of the lens to the top of the projector bracket. Add 2.5 (PDS), 2.8 (SpiroLock ) or 3.8 (FTP) to the calculated total. Ground This total distance will be the location for the bottom rail on the wall plate. Installation Instructions Visit the Premier Mounts website at Page 5

6 UNIU Wood Stud Installation Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION. Step 1 Use an electronic stud finder (not supplied) to locate the center of the stud that is in the wall. Wood Stud Stud finder Step 2 Use a pencil to mark the first mounting point, just above your height mark (from page 5). Mounting Point Mark Height Mark (from page 5) Step 3 Use the level to make sure the wall plate is level from side to side. Place the wall plate over the first mounting point mark and use a pencil to mark the rest of the mounting points. Four (4) mounting points must be used. Two (2) upper mounting points and two (2) lower mounting points. Wood Stud Marking Wall Plate Step 4 Once the mounting points have been marked, use a ¼ drill bit and portable drill to drill the pilot holes. Drill Marking Page 6 Visit the Premier Mounts website at Installation Instructions

7 Step 5 After the pilot holes have been drilled, use four (4) 5 16 x 3 lag bolts and four (4) square washers to mount the wall plate to the wooden studs. Use a ½ socket and socket wrench to finish this step. Lag Bolt and Square Washer UNIU Socket Wall Plate Step 6 Insert and gently tap the upper and lower back plate covers into place. Back Plate Covers Proceed to the Attaching the Projector Arm section. Attaching the Projector Arm Step 1 Locate the mounting hook cutout on the top of the wall plate. Tilt the arm slightly and gently insert the mounting hooks into the mounting hook cutouts. Slowly lower and let the projector arm rest against the wall plate. If using the storage feature of the product, it may be easier to route any wiring at this time (please see Page 14). MAKE SURE THE PROJECTOR ARM IS FULLY SEATED BEFORE RELEASING THE UNIT. Mounting Hook Cutout Mounting Hooks Wall Plate Projector Arm Installation Instructions Visit the Premier Mounts website at Page 7

8 UNIU Step 2 Locate the two (2) lock mounting points on the projector arm. These two points will be aligned with the lock mounting points on the wall plate. Using a security wrench, insert and tighten two (2) M5 x 8mm security head screws. Lock Mounting Point Do NOT overtighten these screws. M5 x 8mm Security Head Screw Security Wrench Throw Distance Calculation Please review your projector mount s user manual before attaching the upper mounting bracket. The correct throw distance (the distance from the projector to the screen) must be determined prior to mounting the projector. Refer to the projector s user s manual to determine the distance from the lens to the front of the screen (X). Measure the distance from the front of the lens to the center of the projector (Y). Measure the distance from the wall to the face of the whiteboard/screen (Z). Add all measurements (X + Y + Z) to determine projector placement on the arm assembly. This measurement will determine where the center of the mount bracket will be located on the arm assembly. Please make note of this measurement. The UNIU can be also used as a wall-mounted standard projector mount as well as a short throw projector mount. Align the projector facing the opposite direction from the wall plate to project the image across the room. Please take into account the projectors throw capabilities prior to mounting in the projector opposite direction. Calculations X = Manufacturers recommended throw distance Z = Distance from wall to face of whiteboard/screen Front Lens Throw Distance = (X + Y + Z) Rear Lens Throw Distance = (X - Y + Z) Front Lens Rear Lens Continue to the Attaching the Projector Mount section. Page 8 Visit the Premier Mounts website at Installation Instructions

9 Attaching the Projector Mount What kind of projector mount are you attaching to the adjustable mounting assembly? UNIU If it is a Fine-Tune Projector (FTP) mount, continue to the Installing an FTP Mount section below. A A If it is a SpiroLock mount, proceed to the Installing an SpiroLock Mount below. B If it is a PDS mount, proceed to the Installing a PDS Mount section on page 10. A A Attach the projector mount to the mounting assembly before attaching the projector itself. Installing an FTP Mount Detach the upper half of the mounting assembly from the lower half. Following the A mounting-hole pattern (Figure 1), use four (4) M4 x 10mm security screws to attach the FTP projector mount to the lower half of the mounting assembly (Figure 2). Do not overtighten. Use the four mounting holes on the collar of the FTP base. Re-attach both components of the mounting assembly. Refer to the FTP user manual for instructions on attaching the projector to the mount. Bottom view of the adjustable mounting assembly Figure 1 M4 x 10mm security screw Proceed to the Adjustable Mounting Bracket Installation section on page 12. Installing a SpiroLock Mount Detach the upper half of the mounting assembly from the lower half. Following the B mounting-hole pattern (Figure 1), use one (1) M8 x 16mm flathead security screw to attach the SpiroLock spindle to the lower half of the mounting assembly (Figure 3). Do not overtighten. The M8 x 16mm flathead security screw is included with the SpiroLock. Re-attach both components of the mounting assembly. Refer to the SpiroLock user manual for instructions on attaching the projector to the mount. Figure 2 M8 x 16mm flathead security screw Proceed to the Adjustable Mounting Bracket Installation section on page 12. Figure 3 Installation Instructions Visit the Premier Mounts website at Page 9

10 UNIU Attaching the Projector Mount (cont d) Installing a PDS Mount How will you attach the PDS mount? If you are using the adjustable mounting assembly, continue to the Attaching the PDS to the Adjustable Mounting Assembly section below. C If you are using only the upper mounting plate for an even lower profile, proceed to the Attaching the PDS to the Upper Mounting Plate section on page 11. C Attaching the PDS to the Adjustable Mounting Assembly Detach the upper half of the mounting assembly from the lower half. Following the C mounting-hole pattern (Figure 1), use two (2) M6 x 12mm security head screws to attach the PDS base box to the lower half of the mounting assembly (Figure 2). You must insert the screws from the bottom of the PDS base box. Detach the base box from the mount, if needed. Re-attach both components of the mounting assembly. Refer to the PDS user manual for instructions on attaching the projector to the mount. Do NOT overtighten these screws. Proceed. to the Adjustable Mounting Bracket Installation section on page 12. Bottom view of the adjustable mounting assembly Figure 1 M6 x 12mm security screw Figure 2 Page 10 Visit the Premier Mounts website at Installation Instructions

11 Attaching the PDS to the Upper Mounting Plate Projector dimensions differ between manufacturers. If the projector hangs too low from the UNIU, the adjustable mounting bracket may be removed. This will allow you to attach the base box directly to the upper mounting bracket for an even lower profile installation. UNIU Detach the upper half of the mounting assembly from the lower half. Use two (2) M6 x 12mm security head screws to attach the PDS base box to the upper mounting plate (Figure 2). You must insert the screws from the bottom of the PDS base box. Detach the base box from the mount, if needed. Refer to the PDS user manual for instructions on attaching the projector to the mount. Do NOT overtighten these screws. Proceed to the Adjustable Mounting Bracket Installation section on page 12. M6 x 12mm security screw Figure 2 Installation Instructions Visit the Premier Mounts website at Page 11

12 UNIU Adjustable Mounting Bracket Installation If you are using the PDS and upper mounting plate assembly, you can still follow the instructions below to attach it to the projector arm. Projector Arm Insert the internal slide plate into the projector arm. Determine which adjustment slot best matches your throw distance calculation (see page 8). Raise the adjustable mounting bracket into position. Align the mounting holes of the upper mounting plate with the mounting holes of the inner slide plate. Two (2 - one per screw) ¼ nylon washers must be placed between the adjustable mounting bracket and the projector arm (see inset to the right). ± ± Secure and finger-tighten two (2) M6 x 16mm security head screws. ² ² If needed, determine the Throw Distance again. ³ ³ Once the correct throw distance has been determined, use the security wrench (supplied) to tighten the mounting screws. Projector mount not shown. Adjustment Slot Inner Slide Plate Upper Mounting Plate Adjustable Mounting Bracket Calculated Throw Distance ¼ Nylon Washer M6 x 16mm Security Screw If the adjustable mounting bracket needs to be adjusted, the four (4) M6 x 12mm security screws may be loosened so that the bracket can be moved ±2. Once the desired height has been achieved, re-tighten the hardware. Do NOT overtighten these screws. Security Wrench Continue to the Utilizing the Storage Feature section. Projector mount not shown. Page 12 Visit the Premier Mounts website at Installation Instructions

13 Utilizing the Storage Feature The storage feature may be used to store electronic components. There is an accessible door on each side of the storage enclosure. It may be securely held shut with the use of four (4) M5 x 8mm security head screws. It may be easiest to pre-wire all cables down the arm (or extension) at this time. Open the storage door that is located on the side of the wall plate. Place the electronic components inside the storage enclosure. Make all electronic connections at this time. Close the storage door and secure using two (2; 1 upper and 1 lower) M5 x 8mm security head screws. Tighten using a security wrench. Repeat this process for the other side as well. Proceed to the Cable Management section. Electronic Components Door UNIU Security Wrench M5 x 8mm Security Screw Installation Instructions Visit the Premier Mounts website at Page 13

14 UNIU Cable Management The cable access holes are located at the end of the short throw mount and on the wall plate. Route the cables through one end of the UNIU and out the other end. Attach the end cover with an M5 x 8mm security head screw. You may direct the cables out the end of the UNIU. The end cover has a perforated tab to allow cables to pass out the end. Pliers must be used to bend the perforated tab. If the cables will not fit, the end cover may be removed by loosening and extracting the M5 x 8mm security screw. UNIU Electronic Components Electronic Components Cables Cable Opening Projector Hook-Ups UNIU M5 x 8 Security Screw End Cover Extension Bracket Perforated Tab Page 14 Visit the Premier Mounts website at Installation Instructions

15 Technical Specifications All measurements are in inches(mm). UNIU MAX DIST. MIN DIST Installation Instructions Visit the Premier Mounts website at Page 15

16 UNIU Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor costs. What is Not Covered; Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, PROJEC- TORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS. PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS IS NOT RESPON- SIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM- AGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem, the purchaser s name, address, and telephone number. General inquiries can be addressed to Premier Mounts Customer Service at Warranty claims will not be accepted over the phone or by fax. Premier Mounts Attn: Warranty Claim 3130 East Miraloma Ave. Anaheim, CA How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Disclaimer Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Premier Mounts makes no representation of warranty, expressed or implied, regarding the information contained herein. Premier Mounts assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Page 16 Visit the Premier Mounts website at Installation Instructions

17 CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS PDS-PLUS Versatile Projector Mount Model: PDS-PLUS/PDS-PLUS-W NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA USA USA and Canada Phone: Fax: Other Locations Phone: (001) Fax: (001) EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) Fax: +44 (0) G

18 Contents Contact Premier Mounts with any questions: (800) PDS-PLUS/PDS-PLUS-W Weight Limit... 2 Warning Statements... 2 Installation Tools... 3 Parts List... 3 Features... 4 Introduction... 5 Optional Mounting Configurations... 5 Installing the PDS-PLUS/PDS-PLUS-W... 6 Ceiling Installation - Pipe... 6 Ceiling Installation - Wood Stud... 6 Ceiling Installation - Solid Surface... 8 Attaching the PDS-PLUS/PDS-PLUS-W to the Projector... 8 Attaching the Projector Plate... 9 Selecting the Mounting Hardware... 9 Multiple Mounting Point Installation... 9 Single Mounting Point Installation Attaching the PDS-PLUS/PDS-PLUS-W Base Base Box Adjustment Securing the PDS-PLUS/PDS-PLUS-W Projector Mount Technical Specifications Warranty Disclaimer Weight Limit Maximum Projector Weight: 75 lbs. Warning Statements THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING STRUCTURE MUST BE REINFORCED. PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED, AS OUTLINED IN THESE INSTALLATION INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY, OR EVEN DEATH. SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY. PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS. At least two qualified people should perform the assembly procedure. Personal injury and/or property damage can result from dropping or mishandling the projector. If mounting to wall studs or ceiling studs, make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs. Use of an edge-to-edge stud finder is recommended. Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in wall. Cutting or drilling into an electrical line may cause serious personal injury. Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a water or gas line may cause severe property damage or personal injury. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious personal injury. Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact. Page 2 Visit the Premier Mounts website at Installation Instructions

19 2 PDS-PLUS/PDS-PLUS-W Installation Tools The following tools may be required depending upon your particular installation. They are not included. M3 Security Allen Wrench (Supplied) Power Drill Pencil Protective Eyewear Phillips Tip Screwdriver M5 Security Allen Wrench (Supplied) Masonry Drill Bit Ladder ⅛ Wood Drill Bit 1 Tape Measure Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) PDS-PLUS/PDS-PLUS-W Mount Hardware Base Box (Qty 1) Projector Bracket (Qty 1) Mounting Leg - Long (Qty 4) Mounting Leg - Short (Qty 2) #14 x 2 Wood Screw (Qty 2) Nylon Spacer (Qty 2) ¼ Flat Washer (Qty 2) Escutcheon Ring (Qty 1) External Tooth Washer (Qty 4) Phillips Head (Qty 1) M6 x 8mm Set Screw Security Head (Qty 1) Phillips Head (Qty 6) Standard Hardware M6 x 12mm Screw w/integrated Washer Security Head (Qty 12) Barrel Cap (Qty 6) M3 Flat Washer (Qty 10) ¼-20 x 5 /16 Screw (Qty 1) M2.5 x 10mm Screw (Qty 4) M2.5 x 12mm Screw (Qty 4) M3 x 16mm Screw (Qty 4) M4 x 12mm Screw (Qty 4) M5 x 12mm Screw (Qty 4) M6 x 12mm Screw (Qty 4) Lock-It Security Hardware M3 Flat Washer (Qty 10) ¼-20 x 5 /16 Screw (Qty 1) M2.5 x 10mm Screw (Qty 4) M2.5 x 12mm Screw (Qty 4) M3 x 16mm Screw (Qty 4) M4 x 12mm Screw (Qty 4) M5 x 12mm Screw (Qty 4) M6 x 12mm Screw (Qty 8) Installation Instructions Visit the Premier Mounts website at Page 3

20 Features PDS-PLUS/PDS-PLUS-W Congratulations on the purchase of your new Premier Mounts PDS-PLUS/PDS-PLUS-W Versatile Projector Mount. The PDS-PLUS works together with our exciting new PDS Base Box. The PDS-PLUS/PDS-PLUS-W has multiple mounting configurations to fit a variety of projectors. The PDS-PLUS/PDS-PLUS-W is truly the most VERSATILE projector mount on the market today. Adjustable Leveling Barrels You can quickly level the mounting legs without any specialized tools Direct Mounting Slots Enable mount to be fastened directly to structural surface Low Profile At less than 2, the PDS Series is one of the lowest profile mounts on the market Lock-It Security Hardware Protect your projector by installing specialized hardware at critical mounting points Mounting Slots Allows you to choose from a variety of mounting options and projector mounting point configurations Mounting Legs Combined with the numerous projector plate mounting slots, the mounting legs allow for near infinite mount configurations Security Leveling Barrel Allows the user to easily secure the mount with a padlock or a steel-cable locking system (PCB-CSL1). The locks (sold separately) would make it nearly impossible for anyone to remove the projector from the mount. Page 4 Visit the Premier Mounts website at Installation Instructions

21 PDS-PLUS/PDS-PLUS-W Introduction Your PDS-PLUS/PDS-PLUS-W mount may be secured to either a single ceiling stud or a solid surface ceiling, such as concrete. Please read these installation instructions once thoroughly before attempting to install your Premier Mounts product. Please take a minute to familiarize yourself with the contents of the package and make sure you have all the parts and tools you need to safely complete the installation. In addition, some steps of this installation may require two people to prevent personal injury and/or damage to your projector. Please observe all warnings in the following installation procedure and utilize proper safety equipment at all times. Optional Mounting Configurations This section contains different configurations, if applicable, that the PDS-PLUS/PDS-PLUS-W can be used with. The CLS adapter will be used in conjunction with the PP-FCTA and PP-FCMA. Please refer to the installation instructions that come packaged with the following products. PP-FCTA PP-FCMA Standard 1-½ NPT AST-2446 APP-2446 AST-1321 APP-1321 Installation Instructions Visit the Premier Mounts website at Page 5

22 Installing the PDS-PLUS/PDS-PLUS-W Ceiling Installation - Pipe Step 1 After the pipe has been properly secured to the ceiling structure, thread the base box to the lower portion of the pipe. PDS-PLUS/PDS-PLUS-W Unpack the PDS-PLUS/PDS-PLUS-W Mount and familiarize yourself with the components. Please take time before you install the PDS-PLUS/PDS-PLUS-W to determine the location of where the PDS-PLUS/PDS-PLUS-W will be mounted. Step 2 Secure the base box to the pipe with the M6 x 8mm set screw and tighten it down using the M3 Security Allen wrench (supplied). M3 Security Allen Wrench Proceed to the Ceiling Installation - Wood Stud section. Ceiling Installation - Wood Stud Step 1 Use a stud finder to locate a ceiling stud closest to your desired installation location. Identify the center of the ceiling stud. Use a pencil to mark the location of the ceiling stud center. The PDS-PLUS/PDS-PLUS-W may be attached to 1-1/2 standard threaded pipe (NPT), to one of Premier Mount s optional ceiling adapters, or to a single wood stud. If using an optional adapter, please refer to the installation instructions that come with adapters. To prevent the stud from splintering, use a 1/8 wood drill bit to drill pilot holes. Stud Center Page 6 Visit the Premier Mounts website at Installation Instructions

23 PDS-PLUS/PDS-PLUS-W Step 1 Separate the Upper Bridge from the Base Box by removing the six (6) M6 x 12mm Phillips head screws (three on each side). M6 x 8mm Set Screw or Security Set Screw Upper Bridge Step 2 Use the appropriate slot openings for single wood stud mounting, depending on your ceiling configuration. The adjustable channel slots on the upper bridge plate will allow you to fine tune the final orientation of the projector. Secure the Upper Bridge to the center of the stud on the ceiling structure at this time using two (2) #14 x 2 wood screws (supplied). Wood Stud Ceiling Surface Mounting Slot Upper Bridge #14 x 2 Wood Screw Step 3 Attach the base box to the upper bridge and secure with the six (6) M6 x 12mm Phillips Head screws (above). DO NOT OVERTIGHTEN THESE SCREWS AT THIS TIME. M6 x 12mm Screw Installation Instructions Visit the Premier Mounts website at Page 7

24 Ceiling Installation - Solid Surface PDS-PLUS/PDS-PLUS-W The PDS-PLUS/PDS-PLUS-W can be mounted to a ceiling with a minimum 6 thickness. Concrete wedge anchors must be used for concrete installation. It is recommended that ¼ wedge anchors be used. A concrete bit must be used to drill the pilot hole. The concrete wedge anchors and concrete drill bit are commercially available. Begin by placing the upper bridge into position against the ceiling, keeping it level. Next, drill holes using the appropriate concrete bit for your anchor. Insert a concrete anchor into each hole. ± ² ² Remove the nuts and flat washers from the concrete wedge anchors. ³ ³ Once all of the anchors are in place, move the upper bridge back into position. Attach the nut onto the threaded shaft that is protruding from the ceiling. µ µ Do not tighten until all nuts and flat washers are in place. Mark off four holes to be used for securing the mount and place the upper bridge aside. ± If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the ceiling. Proceed to the Attaching the PDS-PLUS/PDS-PLUS-W to the Projector section. Attaching the PDS-PLUS/PDS-PLUS-W to the Projector To truly show the versatility of the PDS-PLUS/PDS-PLUS-W, the following pictures will show a variety of configurations that can be achieved with the PDS-PLUS/PDS-PLUS-W. Your individual application will depend on the purchased projector. Locate the mounting points on the bottom of the projector (see arrows above for sample mounting points). Proceed to the Attaching the Projector Plate section. Page 8 Visit the Premier Mounts website at Installation Instructions

25 PDS-PLUS/PDS-PLUS-W Attaching the Projector Plate Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector. Use a pencil to mark the depth of the threaded insert on the small straw or toothpick. Mark the straw or toothpick 1/8 above the depth of the threaded insert, as shown in Figure 1. Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1/8 allowance mark. ± ± Locate the correct diameter screw for the threaded insert. If the screw you selected is longer than the 1/8 allowance mark on the small straw or toothpick, as shown in Figure 2 and Figure 3, do not use this screw. The screw length must not bypass the mark. ² ² Test each size of the screws provided. The correct screws should thread easily into the mounting point and not pull out when tension is applied. Small Straw or Toothpick Marking the 1/8 Allowance Does your projector have multiple mounting points or a single mounting point? The PDS-PLUS/PDS-PLUS-W comes with the option of using Lock-It Security Screws. To use the security screws, simply replace the M6 x 12mm Phillips Pan head screws with the M6 x 12mm security screws. Once the hardware has been changed, adjust the PDS-PLUS/PDS-PLUS-W and tighten down the M6 x 12mm security screws using the M5 Security Allen wrench (supplied). Small Straw or Toothpick Depth Plus 1/8 Allowance Mark Small Straw or Toothpick Depth Plus 1/8 Allowance Mark If your projector has multiple mounting points, proceed to the Multiple Mounting Point Installation section. If your projector has a single mount point, remove the pre-installed mounting legs on the universal projector plate and skip to the Single Mount Point Installation section. Multiple Mounting Point Installation Step 1 Locate the projector s mounting points. Position an appropriate number of mounting legs on the projector. The four long mounting legs come pre-installed, but you can use three (3) or four (4) long mounting legs and/or short mounting legs, depending on what the projector requires. The number and placement of mounting points on projectors varies between projector manufacturers. Refer to you projector s technical specifications for the number and location of the mounting points on your specific projector. Proceed to the Securing the PDS-PLUS/PDS-PLUS-W Projector Mount section. Installation Instructions Visit the Premier Mounts website at Page 9

26 Step 2 PDS-PLUS/PDS-PLUS-W Only attach to the projector manufacturer s specified mounting points on the projector chasis with a minimum three mounting legs. Please follow all safety instructions specified by the projector manufacturer as well as the safety instructions outlined in this manual. Depending on your application, the long mounting legs and the short mounting legs may be used together. There are multiple configurations that may be used combining the long mounting legs with the short mounting legs. Attach the appropriate number of mounting legs to the projector using the corresponding mounting hardware. Do not tighten the mounting hardware at this time. Step 3 If the mounting legs need to be leveled, rotate the leveling barrels to level the mounting bracket. To raise the mounting legs, rotate the leveling barrel clock-wise. To lower the mounting leg, rotate the leveling barrel counter clock-wise. Raise or lower each of the mounting legs, by rotating the leveling barrels, until all of the mounting legs are at an equal height. Lower the mounting leg by rotating the leveling barrel counter-clockwise. Raise the mounting legs by rotating the leveling barrel clockwise. When the desired position is achieved, tighten the mounting screws to the projector and then tighten the hex head leg screws with the M5 Allen wrench. Mounting Hardware Too Long? The depth of some projector mount points may prevent you from tightening the M2.5 and M3 mounting hardware. You can reduce the length of the M2.5 and M3 mounting hardware by stacking up to a maximum of five (5) M3 flat washers inside the leveling barrel. Avoid stacking too many M3 washers; the mounting hardware must thread into the projector mount point at least four (4) complete turns. Page 10 Visit the Premier Mounts website at Installation Instructions

27 PDS-PLUS/PDS-PLUS-W Step 4 Identify the projector s approximate front-to-back center of gravity. Place your hands on each side of the projector and gently lift it an inch from the surface on which it is resting. Carefully adjust your grip on the projector until it seems balanced from front-to-back. Mentally note the apparent center of gravity. Identify the projector s approximate side-to-side center of gravity. Place your hands on the front and back of the projector and gently lift it an inch from the surface on which it is resting. Carefully adjust your grip on the projector until it seems balanced from side-to-side. Mentally note the apparent center of gravity. Place the PDS-PLUS/PDS-PLUS-W Projector Plate (if not already attached) on top of the mounting legs with the center of the plate as close as possible to the projector s center of gravity. Side-to-Side Center of Gravity Front-to-Back Center of Gravity Step 5 Position the legs accordingly for best configuration. You may raise or lower each leg independently by turning the leveling barrels. Secure the legs to the projector plate by screwing M6 x 12mm security screws into the M6 square nut (do not overtighten) on the mounting legs. Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the PDS-PLUS/PDS-PLUS-W Projector Plate. If the M6 square nut is not aligned with any slot, you can use any thin implement, such as a toothpick, to nudge it into alignment. Sliding M6 Square Nut Step 6 Tighten the mounting screws which secure the mounting legs to the projector. Do not overtighten the mounting screws. Installation Instructions Visit the Premier Mounts website at Page 11

28 Step 7 Attach the Projector Plate (if not already attached) to each of the mounting legs by inserting and tightening one (1) M6 x 12mm screw through the Projector Plate into the M6 square nut on each of the mounting legs. PDS-PLUS/PDS-PLUS-W Do not overtighten the M6 x 12mm screws. Insert one (1) Barrel Cap into the end of each leveling barrel (except the security leveling barrel). Proceed to the Attaching the PDS-PLUS/PDS-PLUS-W Base section. Single Mounting Point Installation If your projector has only one mounting point, a ¼-20 x 5/16 screw must be used to attach the mount to the projector. Please refer to the following three steps: Determine where the mounting point is located. Place the projector plate over the mounting point. Insert the ¼-20 x 5 /16 security screw. Do not overtighten the ¼-20 x 5 /16 screw. Proceed to the Attaching the PDS-PLUS/PDS-PLUS-W Base section. Page 12 Visit the Premier Mounts website at Installation Instructions

29 PDS-PLUS/PDS-PLUS-W Attaching the PDS-PLUS/PDS-PLUS-W Base Step 1 Place one (1) nylon washer and one (1) ¼ flat washer over the hinge pin. Insert and tighten one (1) M6 x 12mm screw. Repeat and for the opposite hinge pin. You can use either the standard hardware or Lock- It security hardware. Replace eight (8) M6 x 12mm screws and one (1) M6 x 8mm set screw. Step 2 Raise the projector (with the mounting bracket attached) and hook the projector bracket over the hinge pins. Make sure the bracket is resting on the Base Box before letting go of the projector. Step 3 Insert the four (4) M6 x 12mm tilt adjustment screws, two (2) per side. You can use either the standard hardware or Lock- It security hardware. Tighten all screws. Do not overtighten the mounting screws. Proceed to the Base Box Adjustment section. Installation Instructions Visit the Premier Mounts website at Page 13

30 Base Box Adjustment You can adjust the roll of the projector by loosening the three (3) front and rear M6 x 12mm screws. Do not fully loosen the screws, as the mount may drop. Set the desired roll and then tighten the screws. First tighten the center screws and work your way to the outside screws, making any final adjustments prior to tightening the last two screws. You can adjust the tilt of the projector by loosening the two (2) M6 x 12mm screws on each side of the Base Box. Set the desired tilt and then tighten the screws, making any final adjustments prior to tightening the last two screws. If your projector is not holding the tilt, install the four (4) external tooth washers on the four (4) M6 x 12mm Phillips head screws w/ Integrated Washers. PDS-PLUS/PDS-PLUS-W ± ± Once all adjustments have been made, tighten all hardware. Securing the PDS-PLUS/PDS-PLUS-W Projector Mount Your PDS-PLUS/PDS-PLUS-W Projector Mount includes one (1) Security Leveling Barrel which can provide additional theft deterrence for your projector. Shown below are two examples of how you can use the security leveling barrel to make your projector installation more secure: the PCB-CSL1 Security Cable (sold separately) or padlock (combination or keyed; sold separately). Follow the instructions below to install and secure the security leveling barrel. If you choose to install the security leveling barrel, please follow the instructions outlined below. Determine which leveling barrel will be removed. Remove the mounting screw. Remove the leveling barrel by turning the leveling barrel counter-clockwise. Thread in the security leveling barrel clockwise. ± ± Insert and tighten the mounting screw. ² ² Attach theft deterrent device (PCB-CSL1 or padlock) through the hole that is on the security leveling barrel. PCB-CSL1 Padlock (Combination or Keyed) Page 14 Visit the Premier Mounts website at Installation Instructions

31 PDS-PLUS/PDS-PLUS-W Technical Specifications All measurements are in inches [millimeters]. Installation Instructions Visit the Premier Mounts website at Page 15

32 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY PDS-PLUS/PDS-PLUS-W What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor costs. What is Not Covered; Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS. PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem, the purchaser s name, address, and telephone number. General inquiries can be addressed to Premier Mounts Customer Service at Warranty claims will not be accepted over the phone or by fax. Premier Mounts Attn: Warranty Claim 3130 East Miraloma Ave. Anaheim, CA How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Disclaimer Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Premier Mounts makes no representation of warranty, expressed or implied, regarding the information contained herein. Premier Mounts assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Premier Mounts 2009 Page 16 Visit the Premier Mounts website at Installation Instructions

33 INSTALLATION INSTRUCTIONS CPA-50 Compact Power Amplifier NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA USA USA and Canada Phone: Fax: Other Locations Phone: (001) Fax: (001) EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) Fax: +44 (0)

34 Contents Warning Statements... 2 Installation Tools... 3 Parts List... 3 Features... 4 Installing the Compact Power Amplifier... 5 Introduction... 5 Wiring... 5 Installing the Power Amp... 7 Setup... 8 Line Gain Control and Volume Setup... 8 Mic Gain Control Setup... 9 Technical Specifications... 9 Notes Warranty...11 Disclaimer...11 CPA-50 Warning Statements Prior to the installation of this product, these installation instructions must be read and completely understood. Keep these installation instructions in an easily accessible location for future reference. Proper installation procedure by a qualified service technician must be followed, as outlined in these installation instructions. Failure to do so could result in property damage, serious personal injury, or even death. Safety measures must be practiced at all times during the assembly of this product. Use proper safety equipment and tools for the assembly procedure to prevent personal injury. Premier Mounts does not warrant against damage caused by the use of any Premier Mounts product for purposes other than those for which it was designed or damage caused by unauthorized attachments or modifications, and is not responsible for any damages, claims, demands, suits, actions or causes of action of whatever kind resulting from, arising out of or in any manner relating to any such use, attachments or modifications. Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in wall. Cutting or drilling into an electrical line may cause serious personal injury. Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a water or gas line may cause severe property damage or personal injury. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious personal injury. Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact. Contact Premier Mounts with any questions: (800) techsupport@mounts.com Page 2 Visit the Premier Mounts website at Installation Instructions

35 CPA-50 Installation Tools The following tools may be required depending upon your particular installation. They are not included. Hand Held Drill Pencil Level Protective Eyewear 18 AWG Wire Stripper Hammer Ladder #1 Flat Blade Screwdriver Tape Measure M5 Security Allen Wrench #1 Phillips Tip Screwdriver Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) Amplifier Hardware Compact Power Amp (Qty 1) AC Adapter (Qty 1) AC Connector (Qty 1) 4-Pin Captive Screw Plug (Qty 1) 3-Pin Captive Screw Plug (Qty 1) Rubber Foot (Qty 4) Installation Instructions Visit the Premier Mounts website at Page 3

36 Features CPA-50 The CPA-50 compact power amplifier is designed to work with the GB-Audio or UNI series of short-throw projector arm mounts. The energy-efficient, 50W amp meets Energy Star Class-D specifications and is perfect for a classroom or meeting room environment. Automatic Standby Standby mode activates if no input signal is detected for 20 minutes. Front View Line Gain Use the Line Gain potentiometer on the front panel to control the gain on the mixed signal. Mic Gain Use the Mic Gain potentiometer on the front panel to control the gain on the mic signal. Mic Input Designed to work with an RF or IR wireless microphone receiver. The mono sound will be evenly mixed into the left and right amp channels. Do not use with wired microphones (dynamic or condenser). Back View External Volume Control Input Mixing The CPA-50 has two line-level stereo inputs on RCA connectors plus one line-level stereo input on a 3.5mm mini-jack and one subline level (30 mv) mono microphone input on a 3.5mm mini-jack. Input switching is not needed. All signals are mixed inside the amp at a 1:1:1 ratio. You can plug in an optional 10k volume pot. The external volume control only adjusts the mixed line-level signals, not the mic signal. Page 4 Visit the Premier Mounts website at Installation Instructions