V

Transcription

1 4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT R set by hand or by optional RCU (Remote Control Unit) X 65 R2 X 65 4-Port Antenna / 65 / /17.5dBi 0 8 /0 8 T Type No V01 Lowbands R1; R2 Frequency range MHz Polarization +45, , , 45 Average gain dbi Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar db > 27 > 27 > 27 Cross polar ratio Maindirection 0 Sector ±60 db Tracking, Avg. db 1.0 Squint ±2.5 Vertical Pattern: Half-power beam width Electrical tilt 0 8, continuously adjustable Sidelobe suppression for first sidelobe above main beam avg. T db Impedance Ω 50 VSWR < 1.5 Isolation, between ports db > 30 Intermodulation IM3 dbc < 150 (2 x 43 dbm carrier) Max. power per input W 400 (at 50 C ambient temperature) Mechanical specifications /a Subject to alteration. Input Connector position Adjustment mechanism 4 x 7-16 female Rearside 2x, Position bottom continuously adjustable Wind load (at Rated N lbf Frontal: Wind Speed: 150 km/h) Maximal: Max. wind velocity km/h mph Height/width/depth mm inches Category of mounting hardware Weight kg lb Packing size mm inches Scope of supply / 576 / / 22.7 / 3.9 H (Heavy) 24 / 26 (clamps incl.) 52.9 / 57.3 (clamps incl.) 2500 x 600 x x 23.6 x 5.9 Panel and 2 units of clamps for mm inches diameter V01 Page 1 of 2

2 Accessories General Information Accessories (order separately if required) Type No. Description Remarks mm inches Weight approx. kg lb Units per antenna clamp Mast diameter: clamp Mast diameter: downtilt kit Downtilt angle: Accessories (included in the scope of supply) clamp Mast diameter: Material: Grounding: Reflector screen: Weather-proof aluminum. Fiberglass radome: The grey fiberglass radomes of these antennas are very stable and extraordinarily stiff. They are resistant to ultraviolet radiation and can also be painted to match their surroundings. All screws and nuts: Stainless steel. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. Detail see below Correlation Table Frequency range Array Connector MHz R1 1 2 MHz R2 3 4 R1 R2 Layout of interface: Detail /a Subject to alteration. Page 2 of V01

3 Mounting Hardware Clamp Included in the Scope of Supply Suitable for mast diameter Antenna mast distance Material of clamp and screws Weight (mm) [inches] (mm) [inches] (kg) [lb] [ ] [ ] Hot-dip galvanized steel / stainless steel 1.1 [2.43] 152 [5.98] 100 [3.94] 72 [2.83] [ ] 40 [1.57] 35 [1.38] 64 [2.52] 125 [4.92] /c Subject to alteration. 40 [1.57] [ ] M10 M A = 25 Nm M8 M A = 20 Nm [ ] Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares. All dimensions in mm and [inches] Page 1 of 1

4 General Instructions for Adjustment Mechanism Description of the adjustment mechanism (protective cap removed): ➀ Twist protection. ➁ Downtilt spindle with integrated scale. ➀ Thread for fixing the pro tective cap or the RCU (Remote Control Unit). ➁ Gearwheel for RCU power drive. To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: 0 max. 0 max. Remove the protective cap and the twist protection completely. Set downtilt angle by rotating the gearwheel. Screw on the twist protection and the protective cap again. Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment: /a Subject to alteration. For a description of RCU installation please refer to the respective data sheet. Page 1 of 2

5 General Instructions for Feederline and RCU Installation for Antennas Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width. Description of bottom end cap (exemplary picture): Adjustment mechanism (protective cap removed) Ventilation hole Spindle with tilting scale 7-16 female (long neck) Colour coding: Correlation of each RF input to: the corresponding adjustment mechanism the frequency range the polarization Installation of the feederline connector and RCU (optional): In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation! Kathrein installation set: Type No Set has to be ordered separately! Set consists of three spanners of divers width 27, 32 and 41 mm 1.1, 1.3 and 1.6 inches 1/2 square actuation according to DIN 3120 Form C Carefully place the connector and fix the nut using a torque-wrench (according to the manufacturers guidelines). After feederline installation, the optional remote control units (RCUs) can be mounted All dimensions in mm inches These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm 1.6 inches /a Subject to alteration. Tighten nuts within a torque range of Nm depending on connector manufacturers specifications, respectively the RCU nut with a torque range of Nm. Page 2 of 2