Operation Manual. 12V Single Kit

Size: px

Start display at page:

Download "Operation Manual. 12V Single Kit"

Alberta Butler
5 years ago
Views:

1 Operation Manual 12V Single Kit Part No Rev C

12V Single Fixture 2 Extension, 25ft 1 Car

2 KIT-140X 12V Single Kit, 12VDC Kit Contents: 2 12V Single Ballast xlr V Single Fixture 2 Extension, 25ft 1 Car Adapter xlr 1 Alligator Clip Adapter xlr 1 Splitter xlr 1 Travel Case Dimensions Weight 21 x 7.5 x 17 14lbs (53.5 x 19 x 43cm) (6.3kg) 2

3 Fixture is comprised of 3 parts: 1. Fixture Shell 2. Lamp Harness 3. Black Louver The Louver is held in place with Velcro fasteners. Clips hold the lamp to the fixture. Locking Lamp Connector: Depress both tabs on the lamp connector and apply to lamp pins. Push lamp into the fixture s Lamp Holder Clips. 3

Most applications for the Fixture are in tight locations, where a strip of double sided Velcro or gaffer tape can hold the Fixture in place.

Insert the mount plate into the receptacle holes on the fixture mating plate. Push down on the two push-pins to lock the plate in place.

To Ensure Proper Operation ALWAYS TURN OFF THE BALLAST BEFORE connecting or disconnecting lamps, harnesses or Head Extension Cables.

4 Most applications for the Fixture are in tight locations, where a strip of double sided Velcro or gaffer tape can hold the Fixture in place. For stand mounting, the Fixture is designed to accept a single mount plate, MTP-K1 (sold separately). Stand Mounting Pull back the two push pins on the single mount. Insert the mount plate into the receptacle holes on the fixture mating plate. Push down on the two push-pins to lock the plate in place. Reverse the process to release the plate. The knurled 3/8 pin can be clamped onto a grip head. Warning! To Ensure Proper Operation ALWAYS TURN OFF THE BALLAST BEFORE connecting or disconnecting lamps, harnesses or Head Extension Cables. Maximum distance, 50ft (2 x 25ft cables) Ballast Operation The 12V Single Ballast (BAL-140X) operates remote from the fixture. Connect the 15 single lamp harness to the extension cable or the Ballast. After the lamp is properly installed, the Ballast can be turned on. Avoid operating in temperatures above 125 F (51 C) or below 32 F (0 C). 4

5 Ballast Operation continued. (Note: The dimmer should be full up when striking the lamp. Once the lamp has come up to full temperature, in 3-5 minutes, then dim to the desired light level.) In cold temperatures the Ballast may take longer to ignite the lamp. If it does not ignite within 5 seconds, switch the ballast to OFF, and try again. If lamp does not strike after 2 or 3 attempts, turn Ballast off, check that the harness, lamp or any extension connections are secure and restrike. A B C D A) Lamp Output.. Lamp harness connects the ballast to the lamp. B) Power Switch. Lights up green when power is present. C) TRIM Adjusts the bottom end of the dimming curve. D) DIMMER.. Adjusts the light level of the lamp. 5

6 Turn the DIMMER clockwise for maximum light output. The 12V Single ballast operates lamp lengths of 15, 24, 36 and 48 T12 or T8. The dimming range is different for each lamp length. The TRIM adjustment located under the carrying handle adjusts the dimming range to accommodate the various lamp lengths. The TRIM pot can also be used to make a lamp fade to black or to stop at a predetermined low light setting. To adjust the TRIM pot: Use a slotted screwdriver to turn the TRIM pot. Clockwise adjusts the lamp brighter, counterclockwise darker. 1. Turn Trim and Dimmer to maximum position. 2. With Lamp type selected and Lamp correctly connected turn on power. 3. Turn DIMMER down to lowest setting. 4. Now turn the TRIM pot counter clockwise to set the lowest light level desired. The BAL-140X power connection is made with 4-pin XLR connectors. Align connectors and insert. When using alligator clips correct polarity is necessary in order to operate the ballast. Red Clip is + (Positive) Black clip is (Negative) To operate two ballasts off the alligator battery clip cable (PWC-AX), use the XLR splitter cable (PWC-X42). 6

7 CFX-15V 15 Fixture/12V PWC-CX DC Car Adapter xlr, 6ft X04-25 Single Extension, 25ft PWC-X42 4-pin XLR Splitter BAL-140X 12V Single Ballast xlr, 12vdc KAS-12V 12V Single Travel Case PWC-AX DC Alligator Adapter xlr, 12ft Lamp Harness 4ft HAR ft HAR ft HAR HAR-1501 X04-A16 Single to 4Bank Combiner MTP-K1 Single mount plate with spare push-pins X04-A9 Single to Double Combiner PWS-137X Power Supply 7A, vac/ 12vdc, 4-Pin xlr 7

8 Kino Flo Lamp w/ Harness Dimensions Lamp Type Length Width 15 Med. Bi-Pin ft Med. Bi-Pin ft Med. Bi-Pin ft Med. Bi-Pin Kino Flo Single Fixture Dimensions Barndoor Weight Fixture Style Length Width Depth Width w/lamps 15 Single /12V N/A 1lb 2ft Single lbs 4ft Single lbs 8

9 BAL-140X 12V Single Ballast xlr, 12VDC Input Voltage: 12VDC Output Frequency: 25 khz Amperage: F30/1.9A, F40/2.8A, F75/4.6A Dimming: 100% - 15% Lamp switching: on/off Ballast size: 7 x 6.5 x 2.5 (18 x 16.5 x 6.5cm) Weight: 2.2lb / 1.0kg Environmental: Disposal of Old Electrical & Electronic Equipment. This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. This product is made of recyclable materials and should be disposed of in accordance with local and state regulations. Kino Flo, Inc N. Hollywood Way, Burbank, CA 91505, USA Tel: website: 9

Operation Manual Mega. 4Bank, Double & Single

Operation Manual Mega. 4Bank, Double & Single Operation Manual Mega 4Bank, Double & Single Part No. 3100012 Rev C 04-20-2009 4Bank Double Single Each System consists of: 1 Mega Fixture 1 Mounting Plate 1 Extension Cable 1 Electronic Ballast 2 (2X)