INSTALLATION INSTRUCTIONS
|
|
- Isabel Johns
- 5 years ago
- Views:
Transcription
1 INFINITI GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION:. APPLICATION: Hood Protector Chrome Nissan Armada (004) Nissan Titan (004) 3. PART NUMBER: 4. KIT CONTENTS: Item No. ) ) 3) 4) 5) 6) 7) 8) 9) 0) ) ) 3) 4) Qty Description Hood protector Center clip Inner wing clips Outer wing clips Small screws Self tapping screw Washers Round screw plugs Alcohol wipe Abrasive resistant tape Rubber gasket washers Clear plastic washers Chrome snap-caps Extrusion 5. TOOLS REQUIRED: Clean Rag # Phillips Screwdriver Allen / Hex Key Non Permanent Pen or Pencil 6. INSTALLATION PRECAUTIONS / NOTES: ) Clean hood protector with mild soap and water us ing a soft cloth or chamois. ) Caution: Never use ammoni a based cleaners or solvents. 3) Failure to ensure that the clip rests on the abrasi ve resistant tape may result in permanent paint damage. 4) Before securing t he hood protector, en sure that the part is centralized with hood. 5) Do not over tighten screws. of 5 Fit - HG88 /0/09
2 7. INSTALLATION PROCEDURE 3. Thoroughly clean the front of the hood and raise the hood, as show n in figure. Figure. Cleaning hood areas 3 4. Note the two holes in the underside of the hood, as shown. Clean the hood lip above thes e holes with the alcohol wipe provided and wipe with a dry clean cloth, as shown in figure. Figure. 3. Adhere the abrasive resist ant tape to the hood lip as per figure 3; half on the underside and half on the top of the hood. ABRASIVE RESISTANT TAPE INNER WING CLIP HOLES Figure 3. Abrasive resistant tape installation ABRASIVE RESISTANT TAPE ROUND SCREW PLUG SELF TAPPING SCREW Figure 4. 3 INNER WING CLIP SQUARE HOLE 4. Note the inner wing cl ips with the square hole. Insert these clips over the tape on the hood lip aligning the square hole in the clip with the round hole in the hood. Insert the round screw plug over the clip and in to the round hole in the hood and secure with the self tapping screw provided. Ensure the square boss on the screw plug sits in the square hole in the clip. NOTE : Failure to ensure that the clip rests on the abrasive resistant tape may result in permanent paint damage. of 5 Fit - HG88 /0/09
3 INNER WING CLIPS 5. Remove the backing from the rubber gasket and attach the gasket to the face of each inner wing clip. Figure Install the hood protector, aligning the appropriate slots in the hood protector with the holes in the inner wing clips. Note the underside hood area that corresponds to the center slots in the hood protector. Mark the center of these slots onto the underside of the hood with a pencil, as shown in figure 6. Remove the hood protector. Figure 6. Mark the center clip positions 3 7. Clean the hood lip at the marked locations with the alcohol wipe provided and wipe with a dry clean cloth. Adhere the abrasive resistant tapes to the hood lip as per figure 7; half on the underside and half on the top of the hood. Figure 7. Abrasive resistant tape installation ALIGN SLOT IN HOOD PROTECTOR WITH THREADED HOLE IN THE CLIP INNER WING CLIPS 8. Install the hood protec tor onto the hood and align the slots in the hood pr otector with the threaded holes in the inner wing clip s, as shown in figure 8. Temporarily secure the hood protector with the screws and washers provided. THREADED HOLE Figure 8. 3 of 5 Fit - HG88 /0/09
4 ALIGN THREADED HOLE IN CLIP WITH SLOT IN HOOD PROTECTOR 9. Refit the hood protector. Temporarily secure the hood protector to the inner wing clips with the screws and washers provided. Do not tighten at this stage. Align the slots in the hood protector with the holes in the center metal clips. It may be necessary to slide the center clips into alignment. See figure 9. Figure Secure the hood protector to the center metal clips with the screws and washers provided, as shown in figure 0. Align hood protector centrally, then tighten the inner wing clip screws, and finally the center metal clip screws. NOTE: DO NOT OVER TIGHTEN SCREWS. Figure 0. Securing Hood Protector 3. At the outer wing clip locations, clean the areas with alcohol wipe provided and wipe with a dry clean cloth. Adhere the abrasive re sistant tape to the hood lip as per figure ; half on the underside and half on the top of the hood. Figure. WING CLIP. Lift the hood protecto r and slide the outer wing clips over the hood edge at the noted outer wing clip positions, as shown in figure. NOTE : Failure to ensure that the clip rests on the abrasive resistant tape may result in permanent paint damage. LIFT THE HOOD PROTECTOR WINGS Figure. 4 of 5 Fit - HG88 /0/09
5 3. Secure the hood protector to outer wing clips with the screws and clear plastic washers provided. Apply the chrome snap cap, as shown in figure 3. NOTE: DO NOT OVER TIGHTEN SCREWS. To Remove: Reverse the above procedure. Figure 3. Securing Hood Protector 5mm Figure 4. Attaching Extrusion 5mm 4. Clean the top section of the grille with the alcohol wipe provided. Wipe away any residue with a clean dry cloth. Peel approx. of tape liner from one end of the extrusion and adhere the extrusion 5mm in from the end of the grille, and 5mm out from the rear edge of the grille, as shown. Maintaining this 5mm distance, follow the shape of the grille and gradually remove the tape liner while adhering the extrusion to the grille. NOTE: DO NOT STRETCH THE EXTRUSION. Do not use power tools to install this product. The use of power tools during installation may void the product warranty. Do not slam hood. Clean Hood Protector with a mild detergent and water solution. Do not use abrasive cleaners. 5 of 5 Fit - HG88 /0/09
INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION:. APPLICATION: 3. PART NUMBER: Hood Protector 004 Nissan Armada 004 Nissan Titan 999D X000 4. KIT CONTENTS: Item No. ) ) 3) 4) ) 6) 7) 8) 9) 0) ) Qty
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder T99D5 9PJ0A KIT CONTENTS: Item Qty. A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood
More informationBolt-On/Rugged Fender Flares Nissan Titan (04-15) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY FUEL DOOR CLIP 1 Bolt Kit Included QTY ALCOHOL TOWELETTE 4 M4 SCREW 1 ALLEN KEY BOLT 42 CLIP.9MM 2 ABRASIVE RESISTANT
More informationBolt-On/Rugged Fender Flares Dodge Ram 1500/2500/3500 (09-12) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29.0ft ALCOHOL TOWELETTE 4 ALLEN KEY BOLT 42 NUT 42 Ensure
More informationInstallation Instructions Bolt-On Fender Flares Ford F150 (09-12) Part #17394
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29.5ft ALCOHOL TOWELETTE 4 BLACK HEX BOLT 42 RETAINING CLIP.9mm
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: Moonroof Wind Deflector Nissan Altima PART NUMBER: 999D UZ000 KIT CONTENTS: Item Qty. Description Service Part Number A B C D E F G H 1
More information2011 Honda Accord Coupe Fine Mesh Grille
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED 2011 Honda Accord Coupe Fine Mesh Grille Replacement Upper / Lower Overlay Part #: Complete #1124-0102-11 / Black Ice
More informationVOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano. Upper and Lower Overlay Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano Upper and Lower Overlay Mesh Grilles Upper Chrome Mesh Part #1318-010U-15 / Lower Chrome Mesh Part #1318-010L-15
More information3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS VEHICLE DESCRIPTION: NISSAN NAVARA D0 DUAL CAB 3 Pce Tonneau Cover with OEM Sports Bar 3 Pce Tonneau Cover with EGR Sports Bar PLACE THESE INSTRUCTIONS
More informationRev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION
Rev. 04-10 QTY 3D PART NO. DESCRIPTION 1 691609 FRONT BUMPER REPLACEMENT 1 691610 RIGHT SIDE SKIRT 1 691611 LEFT SIDE SKIRT 1 691612 REAR LOWER SKIRT 4 3M 94 3M ADHESION PROMOTER 16 #8 X ¾ SELF DRILLING
More informationINSTALLATION INSTRUCTIONS Accessory S P/N 08R04-SWA-100 Application 2010 CR-V Publications No. AII 42599 Issue Date AUG 2009 NOTE: Visors may not be legal in all states. Please check the laws of your state
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory MOON P/N 08R01-SZA-101 Application 2014 PILOT Publications No. AII 50258 Issue Date AUG 2013 PARTS LIST TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 10 mm Combination
More information2015 Chevrolet Silverado HD E-Power & Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Chevrolet Silverado HD E-Power & Fine Mesh Grilles Upper Black Mesh Part #1415-010U-15EP / Upper Chrome Mesh Part #1415-010U-15EPC
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationCurrent Range Rover Sport STRUT Collection Installation Manual
2014 - Current Range Rover Sport STRUT Collection Installation Manual 1 1. Removing Main Grille and Lower Fascia 1.1 Run a line of low tack masking tape across the front of the bumper below the grille
More informationFORD - F TOOLS CHECK LIST INSTALLATION MANUAL READ CAREFULLY BEFORE INSTALLATION FLOOR LINERS SET F ALL TYPE OF CABS
FORD - F-250 2017 FLOOR LINERS SET F-250 2017 PART # : 1140NNTJFO23A12 LH ALL TYPE OF CABS RH NOT DESIGNED OR RECOMMENDED FOR MODELS EQUIPPED WITH VINYL FLOORING TOOLS ONLY SUPER CREW CAB PART # : 1140DNTUFO23A13
More information2011 Honda Accord Coupe Fine Mesh Grille
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! Copyright 2010 by E&G Classics, Inc. All right reserved. The reproduction or uti li za tion of this work in any form or any elec tron
More informationGENUINE MUD FLAP (FRONT)
GENUINE MUD FLAP (FRONT) INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, be sure to thoroughly read these instructions. Please
More informationWheel Arch Trim Set. Installation Manual. This section covers installation of the wheel arch trim set.
Wheel Arch Trim Set FORESTER Wheel Arch Trim Set EN PART # E20SSG000 This section covers installation of the wheel arch trim set. Installation Manual Note: Before performing installation, be sure to read
More informationTonneau Cover Fitting Instructions Ford PX Ranger XL Dual Cab With HeadBoard June Current
Tonneau Cover Fitting Instructions Ford PX Ranger XL Dual Cab With HeadBoard June 2013 - Current Part Number: 10129 Package includes 1 x Tonneau Cover 1 x Warranty Card 2 x Bar Bracket (300474) 23 x 4
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27955 SIDE 2005 CIVIC SI Issue Date AUG 2004 PARTS LIST Left side under spoiler Right side under spoiler 6 Plates 8 Clips Template INSTALLATION
More information3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS
3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS TC00d / Vehicle Description: NISSAN NAVARA D0 DUAL CAB 3-PIECE TONNEAU COVER PARTS LIST NO. PART NAME QTY. NO. PART NAME QTY. NO. PART NAME QTY.
More informationNIS NAV AM (MY15 >) - Aluminium Tonneau Cover ATC0051 (silver) ATC0052 (Black) Installation Time: Approx. 60 Minutes WARNING!
Installation Time: Approx. 60 Minutes WARNING! When in the closed position, Aluminium Tonneau Cover must be latched and tailgate must be closed. Failure to do so could result in unexpected opening of the
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Front Protector Kit APPLICATION: G Sedan Sports PART NUMBER: K6010-1NH** (XX Designates color) KIT CONTENTS: Item Qty. Description Part
More informationGround Effects, P/N: (V6), (V8)
, P/N: 92248596 (V6), 92248560 (V8) 3. Open trunk and remove 3 scrivets per side. Retain. Remove LH and RH tail lamp access cover. Retain. Refer to Figure 1. NOTE: Installation is made easier with the
More informationINSTALLATION INSTRUCTIONS: INDIAN SCOUT HI-OUTPUT GRENADES PART# 18554/18654
INSTALLATION INSTRUCTIONS: INDIAN SCOUT HI-OUTPUT GRENADES PART# 18554/18654 Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your Vance & Hines exhaust is designed
More informationIMPORTANT INFORMATION:
Notes to the Technician: E&G is proud to present this package to you and reminds you that for technical in for ma - tion, contact the technical department at 40-38-4900. Do not at tempt in stal la tion
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More information3PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger/Mazda BT-50 (without bedliner)
3PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger/Mazda BT-50 (without bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.
More informationInfiniti Q50* Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! Copyright 2015 by E&G Corporation, LLC. All right reserved. The reproduction or uti li za tion of this work in any form or any elec
More informationVolkswagen New Beetle Body - Exterior 50 Body - Front (Page GR-50)
50 Body - Front (Page GR-50) Body, front Front end, Assembly overview Front fender, assembly overview Lock carrier, removing and installing Lock carrier, service position Noise insulation, assembly overview
More informationLANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS
LANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS Black with aluminum plate -MZ531356EX Black standard -MZ531357EX
More informationInstallation Guide for EcoBrite EndLite LED Light Fixtures
Installation Guide for EcoBrite EndLite LED Light Fixtures BEFORE YOU BEGIN INSTALLATION Read these instructions carefully. Failure to follow these instructions will invalidate the warranty on this product.
More informationWARNING. When installed in accordance with these instructions, the front protection bar does not affect operation of the SRS airbag.
Part Number: 343870 F/Kit 17557 Product Deluxe Combination Winch and Non Winch Bull Bar Description: Suited to Nissan XTERRA 05ON USA Only vehicle/s: WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG;
More information2015 Infiniti QX80 - all models
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! Copyright 2014 by E&G Corporation, LLC., All right reserved. The reproduction or uti li za tion of this work in any form or any elec
More informationWARNING TAKE NOTE OF THE FOLLOWING: THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING ONLY THE HARDWARE SUPPLIED.
ARB WINCH/NONWINCH BUMPER TO SUIT TOYOTA HJ100 IFS PRODUCT No. 3913140 5100050 Top Tube Kit 5100160 Buffer Kit With hole (required when fitting Top Tube) 5100170 Buffer Kit With no hole Fitting Kit No.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S 1998 CIVIC 2/3/4-DOOR All 18767 Issue Date SEP 1997 PARTS LIST Fog Light Kit: P/N 08V31-S01-100 Right fog light (marked R ) Fuse label
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory MOON P/N 08R01-T2A-100 Application 2014 ACCORD 2 AND 4-DOOR Publications No. AII 49981 Issue Date AUG 2013 PARTS LIST Moonroof visor 2 Front brackets 2 Side brackets
More informationQTY 3D PART NO. FORD SERVICE PN DESCRIPTION VAA6Z A FIESTA 5 DOOR (4) PC. KIT
Rev. 08-4 - 2010 QTY 3D PART NO. FORD SERVICE PN DESCRIPTION 1 691620 VAA6Z-5820049-A 2011- FIESTA 5 DOOR (4) PC. KIT HARDWARE SUPPLIED 12 #8 X ¾ SELF DRILLING SCREWS 220 / 18.5 3M VHB DOUBLE FACE TAPE
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationD40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws
HINGE # 1017 2 x Support Plate 1018 8 x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws 2 x Lid mount gas strut bracket 1041 2 x Self tap strut mount 1040 1 x Central Lock bracket 1510
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Item Qty. A B C D E F G H 1 Bedliner Under Rail Bedliner Titan Crew Cab/King Cab/Single Cab 999T1 W3700, 999T1
More informationInstallation Guide Roll Stand Kit for Philips MP20/30 Monitor
Installation Guide Roll Stand Kit for Philips MP20/30 Monitor The purpose of this guide is to: 1. Describe attachment of Post to Base (page 2). 2. Describe attachment of the Utility Basket to the Roll
More informationKawasaki Motors Corp.,U.S.A. Irvine, CA
Kawasaki Motors Corp.,U.S.A. Irvine, CA 9271-2016 Accessory Part Installation Instructions For Model VN900 Classic Windshield Kit: Part No. 99994-005 Please read these instructions carefully and thoroughly
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger (with bedliner)
PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger (with bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SIDE UNDER S Application 2013 CIVIC 2-DOOR Publications No. AII 13069 Issue Date NOV 2012 PARTS LIST 4 Flare nuts Left spoiler 2 Washer-nuts Right spoiler 2 Screws 2
More information2015 Nissan Murano. Upper and Lower Overlay Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! Copyright 2015 by E&G Corporation, LLC. All right reserved. The reproduction or uti li za tion of this work in any form or any elec
More information(2012 Production Onwards) INTEGRATED SIDE STEP INSTALLATION INSTRUCTION. 60 Minutes
NISSAN DUALIS (2012 Production Onwards) INTEGRATED SIDE STEP INSTALLATION INSTRUCTION Accessory Part No. STEP0004 60 Minutes Approx Product Weight: 15kg/33 lb IMPORTANT - PLEASE READ INSTRUCTIONS BEFORE
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2014-15 Toyota Tundra Mesh Grille Upper Insert - Fits ALL model Tundras with chrome or painted factory grille surround Black Mesh Part
More informationINSTALLATION & OWNER S MANUAL
Rev. K, p. 1 of 11 INSTALLATION & OWNER S MANUAL POLARIS FREEDOM CAB INSTALLATION INSTRUCTIONS FOR THE POLARIS RANGER (p/n 2876196-067) IMPORTANT: THIS ACCESSORY WEIGHS 340 POUNDS. PLEASE ADJUST THE VEHICLE
More informationVolkswagen New Beetle Body - Exterior 53 Body - Rear (Page GR-53)
53 Body - Rear (Page GR-53) Body, rear Rear end, assembly overview Rear fender, assembly overview Transparent foil protection for rear fenders Body, rear (Page 53-1) Rear end, assembly overview Note: The
More informationARB WINCH/NON WINCH BUMPER TO SUIT MITSUBISHI PAJERO NM FLARED. EXCLUDING EXCEED MODEL WARNING
ARB WINCH/NON WINCH BUMPER TO SUIT MITSUBISHI PAJERO NM FLARED. EXCLUDING EXCEED MODEL PRODUCT No. 3934020 Sahara Bar 3034020 Sahara Bumper FITTING KIT No. 6171383, 6171762, 6171363 WARNING FOR VEHICLES
More informationExpedition Front Bumper Instructions
Expedition Front Bumper Instructions QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691256 A 8 E X D - 1 7 B 635-AAPLN FRONT BUMPER REPLACEMENT HARDWARE SUPPLIED 10 SELF TAPING SCREWS -10 for Front Bumper PLASTIC
More informationInstallation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket and 10lbs/4.
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS IMPORTANT
For use in cleaning painted metal, glass and other vehicle surfaces. For external use only. Dispose of properly after use. IMPREGNATED WITH 70% ISOPROPLY ALCOHOL TC0d PC TONNEAU COVER INSTALLATION INSTRUCTIONS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 44389 2011 CIVIC S 4- Issue Date AUG 2010 PARTS LIST Left front door visor TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 42449 2010 CIVIC S 4- Issue Date AUG 2009 PARTS LIST Left front door visor TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel
More informationParts List DAKAR PRO Brackets Part # Chevrolet Silverado /4WD
Installation Instructions BR5 Front Bumper Replacement Part Number 24128T Ram 1500 2/4WD (Not compatible with ParkSense, Sport, Express and Rebel Models) Parts List DAKAR PRO Brackets Part # 524765 2014
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For 2007 Toyota Tundra Kit 76380 (Black) and 76381 (Stainless) Your safety, and the safety of others, is very important. To help you make informed
More informationInstallation Guide. Xprezzon Roll Stand
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Xprezzon Roll Stand The purpose of this guide is to describe assembly of the Roll Stand and
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. 1 of 18 INSTALLATION & OWNER S MANUAL KUBOTA RTV 400 CAB (Not for use on RTV 500) These instructions are for installation of the complete cab as well as the modular components. DESCRIPTION:
More informationDouble-check to ensure that all of the parts are included in your shipment. Please immediately contact 3dCarbon if you are missing any part.
5 Pc. Kit Includes QTY 3D PN. DESCRIPTION 1 691815 CRUZE FRONT AIR DAM POLYURETHANE PRE-PRIMERED 1 691816 CRUZE SIDE SKIRT RH POLYURETHANE PRE-PRIMERED 1 691819 CRUZE SIDE SKIRT LH POLYURETHANE PRE-PRIMERED
More informationSUBARU FORESTER - SIDE STEP DIESEL VERSION INSTALLATION INSTRUCTIONS
SUU FORESTER - SIDE STEP DIESEL VERSION INSTALLATION INSTRUCTIONS SS00 VEHICLE DESCRIPTION: PART NUMBER: SUU FORESTER SACC00 R 9 L 0 Care Instructions: Clean Side Steps with a mild detergent and water
More informationRTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1.
RTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1. NOTE: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment
More informationPassenger/Right Support Bracket Driver/Left Support Bracket
PARTS LIST: 1 bumper 24 12mm x 37mm OD x 3mm Flat Washers 1 Driver/left Mounting Bracket 14 12mm Lock Washers 1 Passenger/right Mounting Bracket 14 12mm Hex Nuts 1 Driver/left Lower Support Bracket 2 Plastic
More informationINFINITY MULTA SERIES
ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS
More informationThe M7 Direct Flow Intercooler (DFIC) Installation Guide
The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting
More informationASX / OUTLANDER SPORT SHIFT KNOB MZ525507EX INSTALLATION AND HANDLING INSTRUCTIONS
ASX / OUTLANDER SPORT SHIFT KNOB MZ55507EX INSTALLATION AND HANDLING INSTRUCTIONS Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use the product correctly with proper knowledge
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Illuminated Kick Plate G CONVERTIBLE G6950 JJ500 Item QTY A 1 B 1 C 1 D 11 E 12 F 9 G 1 Description
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2006 CIVIC AII 30895 SIDE 2-DOOR Issue Date SEP 2005 PARTS LIST PARTS LIST Left side sticker Left side under spoiler Right side sticker
More informationCANOPY INSTALLATION INSTRUCTIONS CURVED REAR DOOR Isuzu D-Max 2012 / Holden Colorado RG
CANOPY INSTALLATION INSTRUCTIONS CURVED REAR DOOR Isuzu D-Max 2012 / Holden Colorado RG IF FITTING THIS CANOPY TO RG COLORADO A SEPARATE WIRING PATCH HARNESS IS REQUIRED. ORDER EGR PART NUMBER: RGCOL-PATCH-HARN
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory Application Publications No. 2011 CIVIC AII 44380 S 2-DOOR Issue Date AUG 2010 NOTE: The side under spoilers cannot be installed on a vehicle equipped with splash guards. PARTS LIST
More informationGENUINE MUD FLAP (FRONT)
GENUINE MUD FLAP (FRONT) INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please
More informationInstallation Guide. Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit
Installation Guide Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter. 2. Describe attachment of Mounting
More informationPART NUMBER: MINI Cooper S L4-1.6L SEE * NOTE
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-699 2007-2010 MINI Cooper S L4-1.6L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may
More informationINSTALLATION & OWNER S MANUAL
Page 1 of 16 INSTALLATION & OWNER S MANUAL YAMAHA VIKING CAB KIT WITH HARD DOORS p/n: 1YAMVK fits model years 2014- (fits Yanmar Bull model years 2017-) NOTE: By design, the doors are made to not be removable!
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More informationTOYOTA HILUX 2015 ~ CANOPY INSTALLATION INSTRUCTIONS. Important
CP080 CANOPY INSTALLATION INSTRUCTIONS TOYOTA HILUX 05 ~ Installation Time: Approx. 90 Minutes Installation Time: Approx. 00 Minutes (with ute liner) Do not tighten any bolts, screws and nuts that are
More informationINSTALLATION INSTRUCTIONS JEEP WRANGLER PART# 1050 /
INSTALLATION INSTRUCTIONS 2007-12 JEEP WRANGLER PART# 1050 / 1050-2 PARTS LIST: Qty Description Qty Description 1 Aries Grill guard 10 12mm Lock washers 1 Driver/left mounting bracket 10 12mm Hex nuts
More informationPassenger/Right Top Support Bracket. (2) 10mm Nut Plates
PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # /
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 508514/ 508515 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm
More informationPlace these instructions in vehicle s glove box after installation is complete. Clean Tonneau Cover with a mild detergent and water solution.
Place these instructions in vehicle s glove box after installation is complete Installation Time: Approx. 60 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do
More information(2) Top Support Backing Plates. Passenger/Right Top Bracket. (2) Frame Mounting Brackets. (2) 12mm x 35mm Single Bolt Plates
PARTS LIST: 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting Bracket 8 10mm x 27mm OD x 3mm Flat Washers 1 Passenger/Right Mounting Bracket
More information1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and f
STRUT 2015 GMC Denali Collection Installation Manual " 1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and
More informationInstallation Instructions. Ventvisor Deflector
Installation Instructions Important Safety Information Ventvisor Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. CAUTION - Before driving, ensure
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER CHEVY SILVERADO 1500
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 16 12mm Nylon Lock Nuts 1 Driver Mounting Bracket 8 4mm x 10mm Socket Head Screws 1 Passenger Mounting Bracket 4 Sensor Plugs 4 Support
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. DESCRIPTION: APPLICATION: PART NUMBER: Accent light Kit Cube (MY2013+) 999F3 AW000 - Universal Accent Lighting Kit. 4. KIT CONTENTS: Item QTY Description
More informationInstallation Instructions BR20 Rear Bumper Replacement Part # 28178T Toyo ta Tundra 2/4WD
Installation Instructions BR20 Rear Bumper Replacement Part # 28178T 2014-2016 Toyo ta Tundra 2/4WD Excludes Models with B lind Spot Monitoring & Cross Traffic Alert Parts List Item Qty. Part # Description
More informationQ15P. Mitsubishi MQ Triton Dual Cab
Mitsubishi MQ Triton Dual Cab Page 1 of 12 Fitting Instructions Part Number Mitsubishi MQ Triton Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 41770 2010 RL P/N 08R04-SJA-201 Issue Date JUNE 2009 PARTS LIST INSTALLATION NOTE: Door visor (front left) These instructions show the
More informationQTY 3D PART NO. DESCRIPTION
QTY 3D PART NO. DESCRIPTION 1 691032 V6 FRONT AIR DAM 1 691023 SIDE SKIRT RIGHT 1 691024 SIDE SKIRT LEFT 1 691566 V6 DUAL EXHAUST REAR LOWER SKIRT- 8 3M 94 3M ADHESION PROMOTER 24 #8 X ¾ SELF DRILLING
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08R04-TP6-100 Application 2010 ACCORD CROSSTOUR Publications No. AII 41956 Issue Date NOV 2009 PARTS LIST Left front door visor Illustration of the Door Visors
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2014 ODYSSEY Publications No. AII 49550 Issue Date JUNE 2013 PARTS LIST Fog Light Kit P/N 08V31-TK8-100A 16 Wire ties (Some may not be used) Left fog light
More informationLaser BILLET Main Grille
Laser BILLET Main Grille Main grille - #6219420 / #6219421 2016 TOYOTA TACOMA Parts included (1) Billet Grille - Main Polished - Part #6219420 OR Black - Part #6219421 Hardware included (6) #8 0.7 Screws
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationPART A - SPORTS BAR WITH INTEGRATED STOP LAMP INSTALLATION INSTRUCTIONS
PART A - SPORTS BAR WITH INTEGRATED STOP LAMP INSTALLATION INSTRUCTIONS SB000 Vehicle Description: FORD RANGER 0 Part Number: SBAR007 LIST OF PARTS PLEASE KEEP INSTRUCTIONS IN GLOVE BOX FOR FURTHER USE
More informationVOLKSWAGEN AMAROK 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK & PIECE HARD REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place
More information