Expedition Front Bumper Instructions
|
|
- Gertrude Underwood
- 5 years ago
- Views:
Transcription
1 Expedition Front Bumper Instructions QTY 3D PN. FCS PART NUMBER DESCRIPTION A 8 E X D B 635-AAPLN FRONT BUMPER REPLACEMENT HARDWARE SUPPLIED 10 SELF TAPING SCREWS -10 for Front Bumper PLASTIC CLIPS NOTE: IF VEHICLE IS EQUIPPED WITH FACTORY INSTALLED RUNNING BOARDS NON-POWER OR POWER RUNNING BOARDS YOU HAVE THE OPTION OF REMOVING THEM AND INSTALLING THE 3DCARBON SIDE SKIRTS. IF YOU CHOOSE TO NOT REMOVE YOUR RUNNING BOARDS, PLEASE SKIP THE SIDE SKIRT SECTION OF THESE INSTRUCTIONS. TOOLS & MATERIALS REQUIRED - Philips Edge Screw Driver - Phillips Screw Tip - 90 Degree Angle Screw Gun (if possible) - Clean Wiping Cloths - Air or Electric Drill Motor 1/8 Drill Bit - Lacquer Thinner - Grease Pencil - Grinder For Exhaust Extension installation only CAUTION!!!! IF A HEATED SPRAY BOOTH IS USED FOR BAKING THE PRIMER OR PAINT, DO NOT BAKE OR CURE GREATER THAN 120 F DEGREES FARENHEIT. THE PARTS CAN BE DISTORTED AND PERMANENTLY DAMAGED.
2 PREPPING THE KIT PRIOR TO PAINT The first step is to inspect the parts to make sure you have the correct parts. Refer to the part numbers on the back of the parts to confirm the Year Make Model. Parts that are prepped and painted cannot be returned or exchanged. Using lacquer thinner and a clean cloth clean the tape flange surface on the back of each part where the double sided tape will be applied. Using 1 masking tape, apply the tape 1/8 below the top edge of the part. This will protect the tape flange from getting contaminated during the prepping and painting process. Refer to Prepping and Painting Instructions for Step by Step procedures. APPLYING THE 3M TAPE TO THE KIT After the kit has been prepped and painted, the double face tape should be applied to the parts. The tape is not preinstalled on parts prior to shipping because the tape can be contaminated during the sanding/ priming and painting process. The first step is to clean the tape flange on the back of the parts where the tape will be applied. Make sure the complete tape flange is clean and free of all primer and paint. Using lacquer thinner on a clean rag, thoroughly clean the tape flanges on all parts of the kit. Using the adhesion promoter bottle with felt tip supplied, apply it to the tape flanges be careful not press too hard causing too much to be applied. The adhesion promoter will leave a thin clear polymer primer film that will increase the bonding strength of the double face tape. IMAGE #1 The tape should be applied 1/8 down from the top edge of the part so that it cannot be seen after the kit is installed. The tape should be applied to the flange of each part. Press the tape firmly to the surface to insure good adhesion of the double faced tape. (See Images #1-2) IMAGE #2 Repeat the cleaning and adhesion promoter steps on all parts of the kit.
3 INSTALLING THE FRONT AIR DAM HARDWARE SUPPLIED 10 SELF TAPING SCREWS PLASTIC CLIPS IMAGE #3 Step 1) Locate and remove all factory clips. There are (12) black plastic clips located on the plastic cover. (See Images #3-4) IMAGE #4 Step 2) After removing the clips, remove the plastic cover. Locate and remove the (4) T30 screws that secure the factory grille to the vehicle. (See Images #5-6) IMAGE #5 Step 3) Locate and remove the black plastic clip on the sides of the factory grille. (See Image #7) IMAGE #6 IMAGE #7
4 Step 4) Locate and remove the (2) 10mm bolts that secure the front bumper to the fender. (See Image #8) IMAGE #8 Step 5) Locate and remove the (2) 7mm screws that secure the front bumper to the inner fender well. (See Images #9-10) IMAGE #9 Step 6) Locate and unplug and unbolt the factory fog lights from the factory front bumper. DO NOT DISCARD These will be re-installed on the new 3dCarbon bumper. IMAGE #10 Step 7) Locate the (2) factory brackets that secure the bottom of the bumper to the reinforcement and remove the clip. (See Image #11) IMAGE #11 Step 8) Remove the bumper from the vehicle and place it on a clean, soft working surface. Step 9) Remove the black impact absorber from the bumper. Do not discard. This will be re-installed on the new 3dCarbon front bumper. (See Image #12) IMAGE #12
5 Step 10) Remove the factory front grille. Locate and remove the metal clips that secures the front grille to the factory bumper. Do not discard these clips. They will be re-installed on the new 3dCarbon front bumper. (See Images #13-14) IMAGE #13 Step 11) Locate the (2) brackets on either end of the bumper and remove by drilling out the existing pop rivet. DO NOT DISCARD These will be reinstalled on the new 3dCarbon bumper. (See Image #15) IMAGE #14 IMAGE #15 Step 12) Locate and remove the fender flare extensions on the factory bumper. DO NOT DISCARD These will be re-installed on the new 3dCarbon bumper (See Image #16) IMAGE #16 Step 13) Take the impact absorber removed in Step 9 and place it in the new 3dCarbon front bumper. Secure it to the bumper using the clips supplied. (See Images #17-18) IMAGE #17
6 IMAGE #18 Step 14) Install the aluminum mesh grille. Place aluminum mesh grille on the new 3Carbon grille bumper (See Image #19). Note: The grille fits between the bumper and the black impact absorber. (See Image #20) IMAGE #19 IMAGE #20 Step 15) Secure the aluminum mesh grille to the bumper using the supplied coarse plastic screws and washers. (See Images #21-22). IMAGE #21 IMAGE #22 Step 16) Place the bumper right side up and place the clips through the bumper and into the plastic impact absorber. When placing the plastic clips through the bumper, be sure to align the mesh and the plastic absorber so that the pre-drilled holes line up.(see Image #23 & 24) IMAGE #23
7 IMAGE #24 Step 17) Correct installation of the mesh grille is shown below. (See Image #25 & 26) IMAGE #25 IMAGE #26 Step 18) Install the factory fog lights onto the 3dCarbon bumper. (See Image #27) IMAGE #27 Step 19) Re-install the upper grille onto the new 3dCarbon bumper by sliding it in through the tabs on the lower grille. (See Images #28) After the grille has been properly installed, re-install the locking clips removed in step 10 onto the locking tabs in the same location as previously removed. (See Image #29) IMAGE #28 IMAGE #29
8 Step 20) Reinstall the fender end brackets previously removed in step 11. Secure these to the new 3dCarbon bumper with the supplied pop rivet and washer as seen in image #30 & 31. IMAGE #30 IMAGE #31 Step 21) Reinstall the factory fender flare extensions previously removed in step 12. First, place the fender flare onto the 3dCarbon bumper and check the fit and align the flare.(see Image #32). Once properly aligned, place the plastic washers onto the mounting points and secure using the factory nuts. (See Image #33-34) Do not over tighten because this may cause them to strip. IMAGE #32 IMAGE #33 IMAGE #34
9 Step 22) Once the fender flare extensions are installed, use the supplied ¾ washer and slide it in between the fender flare and the bumper as seen in image #35. Proper installation is shown in image #36. IMAGE #35 IMAGE #36 Step 23) Locate the bumper reinforcement ends on the vehicle. Using the supplied trim-lock rubber, install the rubber on the ends of the reinforcement. (See Images #37-38) IMAGE #37 IMAGE #38 Step 24) Re-install the 3dCarbon bumper back onto the vehicle as previously removed. Check to ensure that all clips removed in the original factory bumper removal are properly re-installed. Step 25) Locate the factory bolt and place the supplied bracket onto the underside of the bumper. Tighten the bracket but be sure not to over tighten as it may distort the bracket. (See Image #39) IMAGE #39 Step 26) Install the supplied clips on the bottom of the bumper. Push the clips through the bumper and into the brackets. (See Image #40). IMAGE #40 3DCARBON BODY KITS CAR BODY KITS
Rev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION
Rev. 04-10 QTY 3D PART NO. DESCRIPTION 1 691609 FRONT BUMPER REPLACEMENT 1 691610 RIGHT SIDE SKIRT 1 691611 LEFT SIDE SKIRT 1 691612 REAR LOWER SKIRT 4 3M 94 3M ADHESION PROMOTER 16 #8 X ¾ SELF DRILLING
More informationQTY 3D PN. FCS PART NUMBER DESCRIPTION
QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691544 A8FOC-17B635-APL FOCUS FRONT AIR DAM 1 691549 A8FOC-17E957-APL FOCUS REAR LOWER 1 691548 A8FOC-10154-APL FOCUS RIGHT SIDE SKIRT 1 691547 A8FOC-10155-APL
More informationQTY 3D PN. FCS PART NUMBER DESCRIPTION
Rev.05-08 QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691224 A6ZEP-17B635-AAPLN MKZ FRONT AIR DAM 1 691202 A6ZEP-5410154-AAPLN MKZ SIDE SKIRT RH 1 691203 A6ZEP-5410155-AAPLN MKZ SIDE SKIRT LH 1 691225 A6ZEP-17E957-AAPLN
More informationQTY 3D PART NO. DESCRIPTION
QTY 3D PART NO. DESCRIPTION 1 691032 V6 FRONT AIR DAM 1 691023 SIDE SKIRT RIGHT 1 691024 SIDE SKIRT LEFT 1 691566 V6 DUAL EXHAUST REAR LOWER SKIRT- 8 3M 94 3M ADHESION PROMOTER 24 #8 X ¾ SELF DRILLING
More informationREV READ BEFORE INSTALLATION OF KIT:
REV. 05-08 QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691509 A7EDG-7820049-AAPLN EDGE BODY KIT- V6 B PCS & EXH TIPS 1 691256 A 7 E D G - 7 8 20049-BAPLN EDGE BODY KIT- V6 8PCS & EXH TIPS W/HITCH 1 691501
More informationDouble-check to ensure that all of the parts are included in your shipment. Please immediately contact 3dCarbon if you are missing any part.
5 Pc. Kit Includes QTY 3D PN. DESCRIPTION 1 691815 CRUZE FRONT AIR DAM POLYURETHANE PRE-PRIMERED 1 691816 CRUZE SIDE SKIRT RH POLYURETHANE PRE-PRIMERED 1 691819 CRUZE SIDE SKIRT LH POLYURETHANE PRE-PRIMERED
More informationQTY 3D PART NO. FORD SERVICE PN DESCRIPTION VAA6Z A FIESTA 5 DOOR (4) PC. KIT
Rev. 08-4 - 2010 QTY 3D PART NO. FORD SERVICE PN DESCRIPTION 1 691620 VAA6Z-5820049-A 2011- FIESTA 5 DOOR (4) PC. KIT HARDWARE SUPPLIED 12 #8 X ¾ SELF DRILLING SCREWS 220 / 18.5 3M VHB DOUBLE FACE TAPE
More informationBolt-On/Rugged Fender Flares Nissan Titan (04-15) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY FUEL DOOR CLIP 1 Bolt Kit Included QTY ALCOHOL TOWELETTE 4 M4 SCREW 1 ALLEN KEY BOLT 42 CLIP.9MM 2 ABRASIVE RESISTANT
More informationPART #137 & # DODGE DAKOTA HOODS
Rev. 11/03 PART #137 & #138 97-04 DODGE DAKOTA HOODS Prefit Before Painting! STEP 1: Adjust hood until proper alignment with matching panels is achieved. STEP 2: Adjust primary latch until it fits into
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. FENDER FLARES P/N 08P21-S3V-200 2003 MDX BII 24553 Issue Date SEP 2002 PARTS LIST Right rear fender flare Left front fender flare Right
More informationBolt-On/Rugged Fender Flares Dodge Ram 1500/2500/3500 (09-12) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29.0ft ALCOHOL TOWELETTE 4 ALLEN KEY BOLT 42 NUT 42 Ensure
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08P21-STX-200 2008 MDX BII 37680 Issue Date AUG 2007 PARTS LIST Left bracket A Left front fender flare Left bracket B Left front bumper
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 33322-36889 UNDER 2007 TL Issue Date MAY 2007 PARTS LIST Front under spoiler Left bracket (Marked L ) Right bracket (Marked R ) 8 Self-tapping
More informationDODGE RAM WITHOUT FENDER FLARES FRONT MUD GUARD INSTALLATION INSTRUCTIONS
DODGE RAM WITHOUT FENDER FLARES FRONT MUD GUARD INSTALLATION INSTRUCTIONS PART NO: 5817 Please read instructions thoroughly before installation. Tools Required Short Phillips screwdriver Center punch Drill
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2012 MDX Publications No. BII 46618 Issue Date OCT 2011 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket
More informationSALEEN SPEEDLAB ROCKER PANELS KIT
= SALEEN SPEEDLAB ROCKER PANELS KIT INSTALLATION MANUAL: 2005 to 2009 Mustang P/N: 10-8002-C12166C Saleen Performance, Inc. 1225 East Maple Rd. Troy, MI 48083 248-743-4800 www.saleen.com IF YOU ARE NOT
More informationInstallation Instructions Bolt-On Fender Flares Ford F150 (09-12) Part #17394
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29.5ft ALCOHOL TOWELETTE 4 BLACK HEX BOLT 42 RETAINING CLIP.9mm
More informationGround Effects, P/N: (V6), (V8)
, P/N: 92248596 (V6), 92248560 (V8) 3. Open trunk and remove 3 scrivets per side. Retain. Remove LH and RH tail lamp access cover. Retain. Refer to Figure 1. NOTE: Installation is made easier with the
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder T99D5 9PJ0A KIT CONTENTS: Item Qty. A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood
More information2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete E
BILLET GRILLS IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete 5122-1900-11E TOOLS REQUIRED Automotive
More informationITEM PART NO. DESCRIPTION QTY BODY - SNORKEL (SS1410HP) " AIR RAM ASSEMBLY BRACKET - UPPER MOUNTING 1
L; SS1410HP SAFARI ARMAX SNORKEL VOLKSWAGEN AMAROK V6 TDI550 3.0L TDI V6 Engine Parts List 10/04/2018 ITEM PART NO. DESCRIPTION QTY 1 910-133-600 BODY - SNORKEL (SS1410HP) 1 2 000-135-960 4" AIR RAM ASSEMBLY
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. 2009 CIVIC HYBRID All 40191 Issue Date AUG 2008 PARTS LIST Rear under spoiler 2 Step bolts 4 Self-tapping screws TOOLS REQUIRED Phillips
More informationINSTALLATION INSTRUCTIONS Accessory S P/N 08R04-SWA-100 Application 2010 CR-V Publications No. AII 42599 Issue Date AUG 2009 NOTE: Visors may not be legal in all states. Please check the laws of your state
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27955 SIDE 2005 CIVIC SI Issue Date AUG 2004 PARTS LIST Left side under spoiler Right side under spoiler 6 Plates 8 Clips Template INSTALLATION
More informationInstruction No Version Part. No , , , , , , , ,
Instruction No Version Part. No. 30744180 1.2 30794160, 30794013, 30794026, 30794039, 31213192, 30794102, 30794138, 30794151, 30794075 Body kit IMG-256183 Page 1 / 13 Equipment A0000162 A0000163 IMG-239940
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SIDE UNDER S Application 2013 CIVIC 2-DOOR Publications No. AII 13069 Issue Date NOV 2012 PARTS LIST 4 Flare nuts Left spoiler 2 Washer-nuts Right spoiler 2 Screws 2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24081 ACCORD 2-DOOR Issue Date SEP 2002 PARTS LIST INSTALLATION NOTE: Rear under spoiler Be careful not to damage the rear bumper and
More informationINSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008-
INSTRUCTIONS INTERCOOLER UPGRADE BMW E82 135i 2008- Parts Included: - Intercooler - Left and right side pipes with hoses - 3 Silicone Hoses ( 2.5 x 3 ) - 1 Silicone Hose 90degree 2.5 elbow - 8 Hoseclamps
More informationSide Rocker Installation Instructions
Side Rocker Installation Instructions Guidelines + Trial fit all parts prior to painting + Do not use the side rockers as an attachment point for tie downs + Every 3-6 months, make sure all fasteners are
More informationBox Contents. 1.) Bumper 2.) Side Bumper Brackets 3.) Vertical Bumper Plate 4.) Lower Bumper Weldment
Installation Manual 2 Box Contents 1 3 2 4 5 6 7 (Images not shown to scale) 1.) Bumper 2.) Side Bumper Brackets 3.) Vertical Bumper Plate 4.) Lower Bumper Weldment 5.) Side Bumper Weldments 6.) Side Strap
More informationIncluded in Hardware Kit. Rear Corners 2-Door. Jeep JK Trail Armor. Set Part #14009 Rev STEP 1 - PRIOR TO INSTALLATION
Jeep JK Trail Armor Set Part #14009 Rev-2 02-23-11 A) B) C) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the trail armor according to these written instructions with the hardware
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Left front trim piece
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationLeft and Right Bar Light L Brackets. Driver/Left Frame Bracket
PARTS LIST: 1 Bumper 14 12mm Nylon Lock Nuts 1 Bull Nose Hoop 2 10mm Double Bolt Plates 1 Winch Tray 4 10-1.5mm x 25mm Hex Bolts 1 Driver/left Frame Mounting Bracket 8 10mm x 30mm x 2.5mm Flat Washers
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. UNDER 2007 CIVIC SI All 33529 Issue Date AUG 2006 PARTS LIST Rear under spoiler Clip Rubber washer 6 Flange bolts 6 Flange nuts TOOLS REQUIRED
More informationAggressive Chin Spoiler CDC#
Note: 2005-2009 Aggressive Chin Spoiler CDC# 110021 Read installation instructions before starting and test fit component before painting. Chin Spoiler is a molded Urethane part. To ensure the quality
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 44686 2011 RL P/N 08R04-SJA-201 Issue Date DEC 2010 PARTS LIST INSTALLATION NOTE: Door visor (front left) These instructions show the
More informationRoush Side Rocker Panel Splitters (10-13 All)
Required tools: Jack stands (2) Floor jack (1 is required but 2 is preferred) Pliers Small Phillips screw driver Drill ¼ Drill bit T15 Torx bit (for some models of vehicle) Hacksaw (for some models of
More informationFront Bumper Refresh Kit (FBR) - Contents WORLD S FIRST TESLA TUNER
Front Bumper Refresh Kit (FBR) - Contents Front Bumper Refresh Chrome V Strip Hardware Kit Hardware Kit Includes: Black Chrome V Strip Clamps (x5) Parking Sensor Brackets (x4) Adhesive (x1) Parking Sensor
More informationINSTALLATION INSTRUCTIONS www.collegehillshonda.com Accessory P/N 08P21-SZA-100 Application 2009 PILOT Publications No. AII 39455 Issue Date MAY 2008 NOTE: The fender trim cannot be installed on vehicles
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More information2011 Honda Accord Coupe Fine Mesh Grille
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED 2011 Honda Accord Coupe Fine Mesh Grille Replacement Upper / Lower Overlay Part #: Complete #1124-0102-11 / Black Ice
More information3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS
3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS TC00d / Vehicle Description: NISSAN NAVARA D0 DUAL CAB 3-PIECE TONNEAU COVER PARTS LIST NO. PART NAME QTY. NO. PART NAME QTY. NO. PART NAME QTY.
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPREMIUM FRONT BUMPER FOR RAM 2500/3500. AEV30239AJ Last Updated: 09/05/17 INSTALLATION GUIDE
PREMIUM FRONT BUMPER FOR RAM 2500/3500 AEV30239AJ Last Updated: 09/05/17 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS THOROUGHLY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 3RD ROW AII 27366 ODYSSEY Issue Date P/N 08R12-SHJ-100 SEP 2004 PARTS LIST Left side rear sunshade Driver s Side 1. Remove the left speaker
More information2010 Mustang V6 Shaker CDC #
- - Incomplete 2010 Mustang V6 Shaker CDC # 1011-7002-01 Component Check List: Quantity/Description Part # Engine Cover Assembly 1011-6000-01 1 Engine Cover w/ Upper Air Tube 0511-2100-01 1 Aluminum Shaker
More informationINSTALLATION INSTRUCTIONS
Hardware: 12M x 40M hex head bolts Qty: 4 12M flat washers Qty: 8 12M lock washers Qty: 4 12M Ny-lock hex nuts Qty: 4 Extension bracket with bolt Qty: 2 8M Ny-lock hex nuts Qty: 2 8M Lock washer Qty: 2
More informationPart No. 8865, 8866, 8885, Rear Fender Flares Stepdown Design Jeep JK, 2/4 Dr.
Part No. 8865, 8866, 8885, 8886 Rear Fender Flares Stepdown Design 2007-12 Jeep JK, 2/4 Dr. PLEASE READ INSTRUCTIONS THOROUGHLY BEFORE PR0CEEDING We have provided complete instructions and specific hardware,
More informationFront aero bumper Lower grille Right air spoiler. Left air spoiler Bolts (15) Self-tapping screws (8)
INSTALLATION INSTRUCTIONS Parts List AERO ACCORD FEB. 2008 Front aero bumper Lower grille Right air spoiler Left air spoiler Bolts (15) Self-tapping screws (8) Nuts (10) Tools and Supplies Required Phillips
More information54531/ FORD FUSION
54531/51531 54531/51531 13-15 FORD FUSION 13-15 FORD FUSION FORD FUSION Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill
More informationRAM Extend-A-Fender Fender Flares Set of 4
RAM Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationXX, TOYOTA, TACOMA FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY
FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY Know safety, no injury. Know injury, no safety. ~Author Unknown If there are any questions, call 1-855-HHTOUGH
More informationINSTALLATION INSTRUCTIONS PARTS LIST. SUPPLIES REQUIRED Isopropyl alcohol Shop towel Masking tape Tape measure. Door visor (front left) INSTALLATION
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 13348 2013 RIDGELINE P/N 08R04-SJC-100 Issue Date SEP 2012 PARTS LIST Door visor (front left) SUPPLIES REQUIRED Isopropyl alcohol Shop
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 3RD ROW P/N 08R12-SHJ-100 2006 ODYSSEY AII 30563-31117 Issue Date OCT 2005 PARTS LIST Left side rear sunshade Driver s Side 1. Remove the
More informationSUBARU FORESTER - SIDE STEP DIESEL VERSION INSTALLATION INSTRUCTIONS
SUU FORESTER - SIDE STEP DIESEL VERSION INSTALLATION INSTRUCTIONS SS00 VEHICLE DESCRIPTION: PART NUMBER: SUU FORESTER SACC00 R 9 L 0 Care Instructions: Clean Side Steps with a mild detergent and water
More informationSS1066HF Jeep JK Wrangler Left Hand Drive CRDI4 2.8Litre-I4 Diesel Engine and EGHV6 3.8Litre V6 Gasoline Engine
SS1066HF Jeep JK Wrangler Left Hand Drive CRDI4 2.8Litre-I4 Diesel Engine and EGHV6 3.8Litre V6 Gasoline Engine Installation Guide Safari SS1066HF Page - 1 of 12 6/10/2009 ITEM PART NO DESCRIPTION QTY
More informationVolkswagen New Beetle Body - Exterior 50 Body - Front (Page GR-50)
50 Body - Front (Page GR-50) Body, front Front end, Assembly overview Front fender, assembly overview Lock carrier, removing and installing Lock carrier, service position Noise insulation, assembly overview
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationGMC Yukon
Torch Series LED Grille TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 41770 2010 RL P/N 08R04-SJA-201 Issue Date JUNE 2009 PARTS LIST INSTALLATION NOTE: Door visor (front left) These instructions show the
More informationSS740HF NISSAN D23 NAVARA (NP300) 2.3Ltr Intercooled Twin Turbo(YS23DDTT Engine) Built: Nissan Motor Co. Thailand
SS740HF NISSAN D23 NAVARA (NP300) 2.3Ltr Intercooled Twin Turbo(YS23DDTT Engine) Built: Nissan Motor Co. Thailand Parts List 21/12/2015 ITEM PART NO. DESCRIPTION QTY 1 435-133-000 BODY - SNORKEL (SS740HF)
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More informationMAXIMA WITH BOSE AUDIO; REAR PARCEL SHELF RATTLE/BUZZ NOISE
Classification: Reference: Date: BT01-030A NTB01-051A October 18, 2001 2000-2001 MAXIMA WITH BOSE AUDIO; REAR PARCEL SHELF RATTLE/BUZZ NOISE ATTENTION: This bulletin Amends the Service Information and
More information11333 INSTALLATION INSTRUCTIONS
11333 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 2011-PRESENT MAKE: MINI COOPER MODEL: COUNTRYMAN STYLE: SEDAN WARNING: NEVER EXCEED YOUR
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25852 PILOT Issue Date AUG 2003 PARTS LIST INSTALLATION NOTE: Door visor (Front left) These instructions show the left door visors being
More informationDESCRIPTION AND OPERATION
FLIGHT COMPARTMENT 1. DESCRIPTION AND OPERATION The windshield is manufactured of acrylic and is adhesive bonded to the fuselage. Replacement is accomplished by removing the interior trim around the windshield,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08P48-T3L-100 Application 2013 ACCORD 2-DOOR Publications No. AII 13018 Issue Date OCT 2012 PARTS LIST Rear bumper applique Illustration of the Rear Bumper Applique
More informationMustang Shaker
2005-2009 Mustang Shaker CDC #110050 ( 05/ 06) or 0711-7000-01 ( 07/ 09) Component Check List: Quantity/Description Part # CDC Installer 1 - Engine Cover Assembly 114050 1 - Aluminum Shaker Scoop 183020
More information54531/ FORD FUSION
2014-2015 FORD Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill Motor PARTS LIST: (4) #8 u-nuts (2) seal brackets (driver
More informationTESLA MODEL S REFRESH FRONT FASCIA INSTALLATION MANUAL FIGURE 1. Unplugged Performance 3523 Jack Northrop Ave, Hawthorne, CA 90250
INSTALLATION MANUAL TESLA MODEL S PARTS QUANTITY INCLUDES FRONT FASCIA 1 PIECE V-STRIPE PANEL 1 PIECE HARDWARE KIT 1 SET PDC SENSOR HOLDERS 4 / 6 PIECES HOOD RELEASE KIT 1 KIT REFRESH FRONT FASCIA PLEASE
More informationJK8 Body Kit KIT CONTENTS 1 K
JK8 Body Kit KIT CONTENTS A B C 1 K6861352 D E G F H 2 K6861352 I M N J K L O P Q R S 3 K6861352 T U V W X Y CALL OUT PART NUMBER DESCRIPTION QUANTITY A P5156021 HARDTOP 1 B P5155997 BULKHEAD 1 C 1PH98/9TZZAE
More information2015+ Mustang Rear Valance Installation Instructions P/N: (R F953) (R F953BS)
2015+ Mustang Rear Valance Installation Instructions P/N: 421894 (R1315-17F953) 421919 (R1315-17F953BS) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang Rear Valance Kit Installation
More informationUpper Class Grille. Main Grille - # / # Dodge Charger. GRILLE Installation Guide. Parts included (1) Main Grille.
Main Grille - # 51480 / #54480 Parts included (1) Main Grille Polished - Part #51480 OR Black - Part #54480 Hardware included (8) - 3/4 x 5/8 L Brackets (8) - #6-32 Nylon Nuts (8) - 3/16 x 1 x 1/32 Black
More informationMINI COOPER COUNTRYMAN
2/19/2013 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** WARNING: ALL
More informationFlight Compartment. 1. General
CIRRUS AIRPLANE MAINTENANCE MANUAL Flight Compartment CHAPTER 56-10: FLIGHT COMPARTMENT GENERAL 56-10: FLIGHT COMPARTMENT 1. General The windshield is manufactured of acrylic and is adhesive bonded to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 CIVIC 4-DOOR Si Publications No. AII 44423 Issue Date AUG 2010 PARTS LIST Template Front under spoiler TOOLS AND SUPPLIES REQUIRED 4 Self-tapping screws
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. THIRD-ROW P/N 08R12-SHJ-100 2008 ODYSSEY AII 38141 Issue Date OCT 2007 PARTS LIST Left rear sunshade Driver s Side 1. Remove the spare tire
More informationSS1135HF Jeep KJ Cherokee CRDI4 2.8Litre-I4 Diesel Engine
SS1135HF Jeep KJ Cherokee CRDI4 2.8Litre-I4 Diesel Engine Parts List 23/2/2010 ITEM PART NO DESCRIPTION QTY 1 965-133-000 BODY - SNORKEL (SS1130HF) 1 2 000-135-800 3 ½" AIR RAM ASSEMBLY 1 3 965-032-000
More informationJK BFH II Front Bumpers
INSTALLATION INSTRUCTIONS INST-17-16-021_A JK BFH II Front Bumpers IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationTONNEAU COVER INSTALLATION INSTRUCTION. Toyota Hilux 407L
TONNEAU COVER INSTALLATION INSTRUCTION Toyota Hilux 407L Piece Tonneau Cover Place these instructions in vehicle s glove box after installation is complete Care Instructions: Clean Tonneau Cover with a
More informationGT Mustang Shaker
CD4II3CU CDC Mustang 5.0 Shaker 2011-2014 2011-2014 5.0 GT Mustang Shaker Part #1111-7000-01 Component Check List: Shaker Assembly: Part # 1 - Aluminum Shaker Scoop 183020 1 Upper Air Box 1111-3301-01
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano. Upper and Lower Overlay Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano Upper and Lower Overlay Mesh Grilles Upper Chrome Mesh Part #1318-010U-15 / Lower Chrome Mesh Part #1318-010L-15
More informationInstallation Instructions. Original Bar Grille
Installation Instructions Part Number 84137 I-sheet Rev. A5 Contents Original Bar Grille For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More informationMINI COOPER HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT DESIGNED FOR USE WITH BALL MOUNT # D-19 / 45519
10/8/2012 PAGE 1 of 6 ITEM 1 QTY 8 Parts List PART NUMBER DESCRIPTION 3/8" CONICAL TOOTHED WASHER TOOLS REQUIRED RATCHET TORQUE WRENCH 12" EXTENSION 12mm SOCKET 8mm SOCKET OFFSET SCREWDRIVER FLAT BLADE
More information8. Front Bumper. Front Bumper A: REMOVAL EI FRONT BUMPER FACE. 5) For OUTBACK model, remove the side garnish of the front fender.
8. A: REMOVAL 1. FRONT BUMPER FACE 1) Disconnect the ground cable from the battery. 2) Turn over the front mud guard, and remove the clips connecting the fender and bumper. 5) For OUTBACK model, remove
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: E92 328i & xdrive PARTS LIST
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-9001 Fits: 2007-13 E92 328i & xdrive PARTS LIST (1) Intake Snorkel (1) Flex Tube (1) Brake Scoop Assy (1) Front Grill (1) Filter (1) Hardware Kit (2) Edge
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33173 UNDER 2007 ODYSSEY Issue Date JULY 2006 PART LIST Front under spoiler 5 Stepped bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2014-15 Toyota Tundra Mesh Grille Upper Insert - Fits ALL model Tundras with chrome or painted factory grille surround Black Mesh Part
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal:
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 28603 S 2006 RIDGELINE Issue Date FEB 2005 PARTS LIST Relay Fog Light Kit P/N 08V31-SJC-100 Right fog light 15 Wire ties Left fog light
More information2018+ Mustang Lower Grill and Chin Spoiler Kits Installation Instructions P/N: (R K945) P/N: (R F775)
2018+ Mustang Lower Grill and Chin Spoiler Kits Installation Instructions P/N: 422081 (R1318-17K945) P/N: 422082 (R1318-17F775) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2018+ Mustang Lower
More informationDetroit Speed, Inc. Second Generation Camaro/Firebird Mini-Tub Kit Camaro/Firebird P/N: ,
Detroit Speed, Inc. Second Generation Camaro/Firebird Mini-Tub Kit 1970-1981 Camaro/Firebird P/N: 041222, 041223 The Detroit Speed Second Generation Camaro/Firebird Rear Mini-Tub Kit is designed to accommodate
More informationInstallation Instructions: (Part # SB614802) Dodge Ram 1500/2500/3500 M1 Rear Bumper Kit
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty Rear M1 1 93-9344 Sensor Mounting Plate 4 93-9345 Sensor Hole Cover Plate 4 93-9347 Trailer
More informationInstallation instructions, accessories. Parking assistance, rear
Installation instructions, accessories Instruction No 31330676 Version 1.4 Part. No. 30758088, 9487266, 30786087, 31359215 Parking assistance, rear Volvo Car Corporation Parking assistance, rear- 31330676
More information