Pressure Sensors. Section C. Pneumatic. Parker Hannifin Corporation Pneumatic Division Richland, Michigan

Transcription

1 Secti Parker Hannifin orporati Divisi

2 Notes trol ompents Parker Hannifin orporati Divisi

3 Index trol ompents MPS- MPS- MVS-0 MPS-3 MPS-3 Stainless Steel MPS-3 MPS-4 MPS-5 MPS-6 MPS-7 MPS-8 MPS-9 Pressure Range Output Type Maximum Hysteresis Media IP Output Mode Rating Adjustment Output Setting Display Page Number 0 to 45 PSI Air, Variable, () NPN / PNP 0 to -30inHG N-orrosive 65 3 to Trim Pot 4-7 With Analog 0 to 4 PSI Gas 0% F.S. 0 to -30 inhg -4.7 to 7.5 PSI 0 to -30 inhg -4.7 to 7.5 PSI 0 to 45 PSI 0 to -30inHG () NPN / PNP 0 to 4 PSI Analog Opti -4.7 to 7.5 PSI 0 to 45 PSI 0 to -30inHG -4.7 to 7.5 PSI Air, () NPN / PNP N-orrosive 65 Gas Air, () NPN / PNP N-orrosive 40 Gas Air, N-orrosive 65 Gas Variable, Push LED Display 00%F.S. Butt (Red) Variable, Push LED Display 00%F.S. Butt (Red) Variable, Push LED Display 00%F.S. Butt (Red) Fluid, () NPN / PNP N-orrosive Variable, Push LED Display Analog Opti 65 to 36L or 00%F.S. Butt (Red) 630 SUS 0 to 45 PSI Air, 0 to -30inHG () NPN / PNP N-orrosive to 7.5 PSI Analog Opti Gas -8 to 8 inho () NPN / PNP 0 to -9.8 inhg Analog Opti Air, N-orrosive 40 Gas Fluid, 0 to 45 PSI N-orrosive Analog 0 to -30inHG to 36L or 630 SUS Variable, Push LED Display 00%F.S. Butt (Red / Green) Variable, Push LED Display 00%F.S. Butt (Red) to 45 PSI () NPN / PNP Air, 0 to -30inHG N-orrosive 40 Trim Pot 5-56 or () Analog 0 to 4.7 PSI Gas Remote Panel: Use with MPS-5,6,8 0 to -30inHG () NPN / PNP -4.7 to 7.5 PSI or () Analog 0 to -30inHG () NPN / PNP -4.7 to 7.5 PSI with Analog 7: () NPN/PNP Analog Opti 40 74: (4) NPN/PNP Air, N-orrosive 40 Gas Air, N-orrosive 65 Gas Variable, Push LED Display 00% F.S. Butt (Red) Fixed, < % F.S Trim Pot Variable, Push LED Display 00% F.S. Butt (Red) SPSD -4.7 PSI to 50 PSI 0 to 000 PSI ( or ) PNP N- Variable, Push LED Display 0 to 3000 PSI Analog Opti orrosive 67 00% F.S. Butt (Red) to 5000 PSI to 36L SUS 0 to 9000 PSI Accessories 8-83 Technical Informati Programming Symbols Legend 87 Glossary Parker Hannifin orporati Divisi

4 Features MPS- Model Number Output Pressure Range MPS-PN-N NPN 0 to 45 PSI MPS-PN-P PNP 0 to 45 PSI MPS-VN-N NPN 0 to -30 inhg MPS-VN-P PNP 0 to -30 inhg MPS-VE-N NPN 0 to -30 inhg MPS-VE-P PNP 0 to -30 inhg MPS-PE-N NPN 0 to 45 PSI MPS-PE-P PNP 0 to 45 PSI MPS- Basic Features Pressure Ranges: Positive Pressure...0 to 45 PSI Vacuum Pressure... 0 to -30 inhg Low Pressure...0 to 4.7 PSI Sensor Outputs Normally Open NPN or PNP Open ollector Transistor Output; 30VD, 5mA Analog to 5 VD Switch Output Adjusted with Potentiometer 3-Turn Trimmer Switch Hysteresis Adjusted with Potentiometer 3/4 Turn Trimmer Output Respse Time Less Than.5 Millisecds E Marked Air and N-orrosive Gases Output Modes The MPS- Series Sensor has two outputs, e open NPN or PNP switch output and e analog output. The Hysteresis Range (h) ctrols the output signal below the Switch Point (H). The Pressure Output Signal is a 3 turn trimmer that sets the switch point of the output. The hysteresis adjustment is a 3/4 turn trimmer to ctrol the output signal 3 to 0% below the pressure output signal. The Analog Output is a to 5 VD signal calibrated to the pressure scale of the sensor. Switch Output 0 h off H -30 in Hg Analog Output Output (Volts) 5 Analog Output off 0 0 Max. Rating Pressure 4 Parker Hannifin orporati Divisi

5 Ordering Informati, Specificatis MPS- Basic Model Number Index Bold Items Are Stocked MPS - V N - P Pressure Range V 0 to -30 inhg L 0 to 4.7 PSI P 0 to 45 PSI Port Size N /8" NPT / M5F R /8" BSPT / M5F G /8" BSPP / M5F E Flange / M5F ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector M8 4-Pin MPS-LN-P MPS-VE-P Specificatis Mounting Bracket for MPS-VE Included. Media Air and N-orrosive Gases Pressure Port N: /8" NPT, R: /8" BSPT, G: /8" BSPP, E: Flange Mount with M5 Female Proof Pressure V: 7.5 PSI, L: 7.5 PSI, P: 7.5 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti 4-Pin, M8 nector with Built-in LED Power Supply 0.8 to 30 VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Analog Output to 5 VD ±0.04, Accuracy Linear 0.5% F.S. Switch Output N.O., Switch Output Mode with Hysteresis Adjustment Output ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor 30VA, 80mA Switch Output Setting H 3-Turn Trimmer Hysteresis Setting h 3/4-Turn Trimmer (3 to 0% of Switch Output Setting) Respse Time <.5ms Repeatability ±% F.S. Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP65 or IP40, E Marked, EM Rating: EN550 lass B, EN5008- urrent sumpti < 0mA Spike Protecti 400 VP, µs Dielectric Strength 000VA, min. Insulati Resistance > 00M ohms at 500VD Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 00 G, XYZ Material Housing: Polycarbate, Pressure Port: Zinc Die-cast Mass.06 oz. (30g) 5 Parker Hannifin orporati Divisi

6 Technical Informati Output Setting Switch Output Setting The Switch Point of the output signal is adjusted with a 3-turn potentiometer trimmer (S). To set the switch point pressure, rotate the trimmer clockwise to raise the switch pressure and rotate the trimmer counter clockwise to lower the switch pressure. MPS- Basic! autis The MPS- Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Potentiometer for the Switch Point Pressure and Hysteresis Range is sensitive. Excessive force or exceeding the limits of the trimmers may cause damage. S H Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Hysteresis Setting The Hysteresis setting is a 3/4 - turn potentiometer trimmer with a range of 3% to 0% below the switch point (S). Rotate the Hysteresis trimmer (H) clockwise to increase the Hysteresis range and rotate the trimmer counter clockwise to lower the Hysteresis range (h). A separate pressure gauge is necessary to accurately adjust these values. For best results, set the switch point (H) of the output signal before adjusting the hysteresis range. For fine tuning the hysteresis range, re-adjust the switch point (S) of the output signal. Installati Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting base. To achieve IP65 rating, cnect the o-ring and barb to a normal envirment with a mm I. D. tube and install screw as shown. S H O-Ring Barb oupling S H -INLUDED- Screw Sensor Pin Out Pin # Brown: 4VD White: Analog to 5VD Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Lead Wiring Brown V+ White Analog to 5 VD Blue 0V Black NPN / PNP Output Internal ircuit H 4 H 4 S 3 S 3 NPN (Sinking) PNP (Sourcing) 6 Parker Hannifin orporati Divisi

7 Dimensis MPS- Basic Dimensis N, R, G /8" Male M8, 4-Pin M5Fx5 LED M8 S H M3Fx4 Places.83 (,) G/8M.3 (8).77 (45).35 (9).6 (5,7) E, Flange Mount M8, 4-Pin.75 (9).39 (0) M3Fx5 4 Places M5Fx5.5.3 (3) (8).06 (,5).35 (9) M4F Places.73 (44).35 (9) LED M8 S H.6 (5,7) M3Fx4 Places (,) (4,7) AMPS-E Flange Bracket for VE Type (Included with E Opti).63 (6). (3).3 (8).75 (9).03 (,8).73 (44).30 (33).8 (30).7 (4.5) Dia. 4 Places.9 (7,4).3 (3,).8 (7,) Accessories ables B-M8-4P-M, Female to Open Lead.96 (5) Dia (9,7) Dia.6 (3) B-M8-4P-5M, Female to Open Lead.96 (5) Dia (9,7) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead (9,7) Dia Female Interface 4-Pin, M (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 3 able Pin olor Brown White 3 Blue 4 Black 7 Parker Hannifin orporati Divisi

8 Features MPS- Model Number Output Pressure Range MPS-VN-N NPN 0 to -30 inhg MPS-VN-P PNP 0 to -30 inhg MPS-RN-N NPN -4.7 to 7 PSI MPS-RN-P PNP -4.7 to 7 PSI MPS- Versatile Features Pressure Ranges: Vacuum Pressure... 0 to -30 inhg ompound Pressure to 7.5 PSI Sensor Outputs: NPN or PNP Open ollector Transistor Output, 30VD, 5mA Switch Point and High-low Programming 4 Selectable Units of Measure (mmhg, -bar, -kpa, inhg) (kgf/cm, PSI, bar, kpa) Automatic Teach Mode Auto Surveillance for Peak Pressure Mitoring Output Respse Time Less Than.0 Millisecds E Marked Air and N-orrosive Gases Error Message Output Modes The MPS- Series Sensor has two independent NPN or PNP open collector output signals. The Switch Output Mode has a switch point programmed by the user at a specified pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. Switch Output 0 h off off H -30 in Hg Window omparator Output 0 off A b off -30 in. Hg off 8 Parker Hannifin orporati Divisi

9 Ordering Informati, Specificatis MPS- Versatile Model Number Index Bold Items Are Stocked MPS - V N - P Pressure Range V 0 to -30 inhg R -4.7 PSI to 7 PSI Port Size N /8" NPT R /8" BSPT G /8" BSPP M5 M5 Female Ejector ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector M8 4-Pin G Grommet Din Rail Blank Without R* With * M5 Port Size Only MPS-VN-P MPS-RM5-NGR Specificatis Pressure Range Vacuum (V) ompound (R) bar: 0.00 bar: 0.0 Units of Measure kpa: 0. kpa: Display Resoluti mmhg: kgf/cm : 0.0 inhg: 0. PSI: 0. Media Air and N-orrosive Gases Pressure Port N: /8" NPT, R: /8" BSPT, G: /8" BSPP, M5: M5 Female Proof Pressure V: 7.5 PSI, R: 6.0 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector, G: m Grommet Open Lead Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Display 3-Digit, 7-Segment LED Display Refresh 0. to 3.0 sec. (Factory set at 0.) Output ircuit NPN (Sinking) or PNP (Sourcing) Output, Open ollector Transistor 30VD, 5mA Switch Output Output Signals, NPN or PNP, Normally Open or losed, LED Indicator Output Modes Hysteresis or Window omparator Respse Time < ms, with Programmable Increments 3, 8, 04ms Repeatability ± 0.% F.S. Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP65 or IP40, E Marked, EM-EN550 lass B, EN Insulati Resistance > 00M ohms at 500VD Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Housing: Polycarbate, Pressure Port: Zinc Die-cast Mass.58 oz. (45g) 9 Parker Hannifin orporati Divisi

10 Technical Informati MPS- Versatile Sensor Pin Out Lead Wiring Pin # Brown: 4VD White: NPN / PNP Open ollector Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Brown V+ White NPN / PNP Output Blue 0V Black NPN / PNP Output Internal ircuit NPN PNP NPN Sinking PNP Sourcing autis! Installati The MPS- Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install as shown using the metal mounting base. To achieve IP65 rating, cnect the o-ring and barb as shown to a normal envirment with a mm I. D. tube. Error Messages Ambient Air Inlet Port Barb O-Ring oupling INLUDED Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er System Error (Internal) tact Factory Er Auto Teach Mode Error Restart Functi E Over current of Output Load current exceeds E Over current of Output maximum 5mA. FFF Applied pressure exceeds Apply pressures within FF pressure range the rating of the sensor 0 Parker Hannifin orporati Divisi

11 Dimensis MPS- Versatile Dimensis N, R, G, /8" Male M8, 4-Pin M5Fx.8.73 (44) M3Fx4 Vent Port.49 (,5).98 (5).55 (4). (5,7) G/8M.3 (8).3 (59).35 (9).63 (6) DIN Rail M5 Female Grommet.40 (6).5 (3,8) M5Fx.8 M3Fx4 Vent Port.49 (,5).98 (5).55 (4). (5,7) (0).69 (88).63 (6) Ejector.73 (44) M3Fx4 Vent Port.49 (,5). (3).98 (5).55 (4). (5,7).4 (3,5).3 (59).35 (9).63 (6) Parker Hannifin orporati Divisi

12 Programming Features MPS- Versatile See page 87 for Symbol Explanati Hold Press x 3 Press x Output Mode Output Set Open Hysteresis or or losed Selecting Window Units of Measure omparator Easy Mode Activati Press 4x Output Mode Hysteresis or Window omparator 4 Press x 5 Press 3x 6 Press 5x Output Setting Output Setting Automatic Teach Mode Hysteresis Hysteresis & Auto Surveillance Mode Mode Vacuum ycle Window omparator Mode Low Window omparator Mode Low Release ycle High High 7 Press 6x 8 Press 7x 9 Press 8x Display Refresh Display Peak Value Settings / Output Bottom Value or Respse Time Their Difference Interval Special Display Features 0 Hold Press Lock Unlock Hold Press Press x Press x Peak Value Bottom Value Press for 3 Secds Zero Reset Parker Hannifin orporati Divisi

13 Accessories MPS- Versatile Accessories ables B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia.6 (3) (9,7) Dia Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M.96 (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 4 3 able Pin olor Brown White 3 Blue 4 Black MPS-AK4 Din Rail.53 (3).69 (88) (0) 3 Parker Hannifin orporati Divisi

14 Features MVS-0 The MVS-0 is a winning combinati with the M, VR-, and VK vacuum generators. The MVS-0 automatically provides an output signal for the blow-off functi without the need of an additial output from the PL. Begin the vacuum cycle with an input signal from the PL to the 0 sensor. The 0 sensor has e output NPN or PNP for vacuum cfirmati and a ctrol output that interfaces directly with the blow-off release pilot valve. With programmable time ctrol features and a special chip driver, the sensor automatically activates the blow-off release when the P L I N Basic PL System O U T Vacuum Pilot Blow-Off Pilot MVS-0 Genius Features Pressure Range: ompound Pressure to 7.5 PSI Time trolled Sensor Intelligent Simple 4-wire System Eliminate I/O for Release Valve Functis with One Rung of ode Automatic Timer (0-9.9 sec.) Functi by Sensor trol Driver for Vacuum Generating and Release Valves Peak Value Preventative Maintenance firmati Respse Time Less Than Millisecds E Marked NPN or PNP vacuum signal from the PL is disctinued. This eliminates, THE PREVIOUSLY REQUIRED, PL output to activate the blow-off release This new technology eliminates PL output requirements by 50% and reduces installati to a simple 4 wire system by wiring the sensor ly. There are 3 modes of operati for various applicatis. The output respse time of the sensor is less than.5 msec. Peak limit preventi maintenance feature is automatically recorded internally. PL System with 0 Sensor P L I N O U T -+ Sensor Output Sensor Output -+ Sensor Vacuum Part Present Output ( V ) ( V ) ( B ) Output Modes Switch Output The MVS-0 Series Sensor has e independent NPN or PNP open collector output signal. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (H). 0 h H -30 in Hg off off 4 Parker Hannifin orporati Divisi

15 Ordering Informati, Specificatis MVS-0 Genius Model Number Index Bold Items Are Stocked MVS P Output ircuit N NPN Sinking Output P PNP Sourcing Output able nector 4-Pin M8 nector Input ircuit Blank NPN Sinking Input P PNP Sourcing Input Note: Output ircuit provides vacuum and blow-off cfirmati signal (Input Signal to PL). Input ircuit ctrols vacuum solenoid valve (Output Signal from PL). Specificatis Pressure Range ompound (R) bar: 0.0 Units of Measure kpa: Display Resoluti kgf/cm : 0.0 PSI: 0. Media N-Lubricated Air and N-orrosive Gases Proof Pressure 6.0 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Display 3-Digit, 7-Segment LED Display Frequency 5Hz ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor Digital Output Individually Selectable N.O. or N.., max 5mA, 30V, with Overcurrent Protecti Mode OP, OP, OP3 Hysteresis: 0 to 00% of Switch Point Respse Time < ms Repeatability ± 0.3% F.S. Thermal Error ±0.% F.S. in Temperature Range: 3 to F (0 to 50 ) General Protecti IP40, E Marked, EM-EN550 lass B, EN5008- urrent sumpti < 45mA, < 5mA When Utilizing Screen Saver Opti Spike Protecti 350 Vp,, µs Dielectric Strength 000 VA min. Insulati Resistance > 00M ohms at 500VD Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Body: Polycarbate Mass.7 oz. (45g) 5 Parker Hannifin orporati Divisi

16 Technical Informati MVS-0 Genius Wiring Diagram M8 Pin # Brown: 4VD White: Input; NPN (0VD) / PNP (4VD) 3 Blue: 0VD 4 Black: Output; NPN / PNP Open ollector Output 0 Pin # Red: Vacuum Solenoid Valve + V Black: Gnd 3 Red: Blow-Off Solenoid Valve + V 4 Black: Gnd Sensor Male Pin Out Internal ircuit Main ircuit (Brown) +V (D 0.8 to 30V) (Brown) +V (D 0.8 to 30V) (White) (White) Sucti/Break ommand Input Sucti/Break ommand Input Digital IN Max. Digital IN 5mA + (Black) OUT (Black) OUT Max. 5mA - Load (Blue) OV (Blue) OV (Red) (Black) 3 (Red) 4 (Black) Vacuum Solenoid Valve Break Solenoid Valve Load or TR nector for cnecti of solenoid valve necti is finished when vum is installed Main ircuit (Red) (Black) 3 (Red) 4 (Black) Vacuum Solenoid Valve Break Solenoid Valve + - or TR nector for cnecti of solenoid valve necti is finished when vum is installed NPN Sinking PNP Sourcing autis! Installati The MVS-0 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er System Error (Internal) tact Factory E Over current of Output Load current exceeds FFF Applied pressure exceeds Apply pressures within FF pressure range the rating of the sensor 6 Parker Hannifin orporati Divisi

17 Dimensis MVS-0 Genius Dimensis M8, 4-Pin.35 (9).73 (44).50 (.7).63 (6).98 (5). (3).4 (3.5).9 (55.5).35 (9).0 (5).63 (6).59 (5).98 (5) 7 Parker Hannifin orporati Divisi

18 Programming Features MVS-0 Genius Operating Modes Descripti of operati modes and terms page 0. Mode: OP "Air servati / Timer Mode: OP "Vacuum Timer Opti" PSI ON (H-d) Blow-Off OFF (h-d) PSI ON (H-d) Blow-Off OFF (h-d) inhg OFF (h-v) ON (H-v) Vacuum (P-v) Peak Value inhg OFF (h-v) ON (H-v) Vacuum (P-v) Peak Value Input Signal Blow-Off Solenoid Vacuum Solenoid ut ON OFF ON OFF T ON OFF T dt T BT Input Signal Blow-Off Solenoid Vacuum Solenoid ut ON OFF ON OFF ON OFF T T dt BT Sensor Output ON OFF T: Vacuum Timer T: Blow-Off Delay Timer BT: Blow-Off Timer Sensor Output ON OFF T: Vacuum Timer T: Blow-Off Delay Timer BT: Blow-Off Timer Timer Mode OP Air servati / Vacuum Valve Timer This Vacuum valve ctrol with the use of timing features cserves air csumpti via the vacuum generator nreturn check valve and sensor hysteresis functi. Vacuum time (t) can be used to ctrol the vacuum valve for a specific length of time ( sec.) after output vacuum level is reached. The vacuum timing functi (t) will remove the signal from the sensor to the vacuum valve allowing the generator check valve system to cserve air csumpti and vacuum. The vacuum valve will re-open for the same length of time (t) when the pressure level drops to the hysteresis setting (h-v). The operati will ctinue until the input signal is stopped. Optial delay timer between vacuum / blow-off (t) and blow-off (bt) timer is available. After selecting OP, set bt, t, and t values by using arrow UP and DOWN keys. To bypass any of these timing functi operatis, simply enter 0.00 secds and the sensor will automatically proceed to the next functi. Timer Mode OP Vacuum Valve Timer This mode is ideal for use with ONVUM generators without check valves. Vacuum timer (t) can be used to ctrol the vacuum for a specific length of time ( sec.) after output is reached. Optial delay timer between vacuum / blow-off (t) and blow-off (bt) timer is available. After selecting OP, set bt, t, and t values by using arrow UP and DOWN keys. To bypass any of these timing functi operatis, simply enter 0.00 secds and the sensor will automatically proceed to the next functi. Note: Output ircuit provides vacuum and blow-off cfirmati signal (Input Signal to PL). Input ircuit ctrols vacuum solenoid valve (Output Signal from PL). 8 Parker Hannifin orporati Divisi

19 Programming Features MVS-0 Genius Operating Modes Descripti of operati modes and terms page 0. Mode: OP3 "Signal trolled Vacuum" PSI inhg H-V / H-d: Switchpoints h-v / h-d: Switchpoints P-V: Peak Value ON (H-d) Blow-Off OFF (h-d) OFF (h-v) ON (H-v) Vacuum (P-v) Peak Value Additial Sensor Features (Available in All Operating Modes) Screen Saver Functi This reduces current csumpti by 0mA and will activate after 0 secds. Peak Value Level (P-v) The sensor records this value for preventative maintenace issues. If this value is not reached the sensor will display an error message (ALP) indicating leaks or wear in the system. Vacuum Level Respse Time (ut) The sensor records the time (sec) to reach Output and will display an error message (ALu) indicating Output has not been reached within the acceptable time (sec) set by the user. Blow-off Time (dt) The sensor records the time (sec) to complete blow-off cycle and will display an error message (ALd) indicating (dt) has not reacting within the acceptable time (sec) set by the user. ut dt Input Signal Blow-Off Solenoid Vacuum Solenoid Sensor Output ON OFF ON OFF ON OFF ON OFF T BT T: Blow-Off Delay Timer BT: Blow-Off Timer Timer Mode OP3 Signal trolled Vacuum The vacuum timer opti (t) is omitted and the PL ctrols the input signal time for the vacuum operati. The delay timer between vacuum / blow-off (t) and the blow-off (bt) timers are still available. After selecting OP3, set bt and t values by using arrow UP and DOWN keys. To bypass any of these timing functi operatis, simply enter 0.00 secds and the sensor will automatically proceed to the next functi. Note: Output ircuit provides vacuum and blow-off cfirmati signal (Input Signal to PL). Input ircuit ctrols vacuum solenoid valve (Output Signal from PL). 9 Parker Hannifin orporati Divisi

20 Programming Features MVS-0 Genius Press x Operating Mode Operating Mode Operating Mode 3 3 Switch Output Outmode Open or losed 4 Screen Saver Peak Vacuum Level Vacuum Level Respse Time Blow-off Time Programming Symbols Legend Operati : Air servati / Timer Operati : Vacuum Timer Opti Operati 3: Signal trolled Vacuum Blow-Off Timer trolled Vacuum Signal with Timer Blow-Off Activati Timer Switch Output Value (H-v) Switch Output Hysteresis Value (h-v) Blow-off Output Value (H-d) Blow-off Output Hysteresis Value (h-d) Error Message - Peak Vacuum Level Error Message - Blow-off Time Output Vacuum Valve (Leave NO) Blow-off Release Valve (Leave NO) Screen Saver Functi Peak Vacuum Level Recorder (P-v) Vacuum Respse Time Recorder Blow-Off Time Recorder Normally Open Normally losed Low or High Signal to Vacuum Valve Error Message - Vacuum Respse Time 0 Parker Hannifin orporati Divisi

21 Accessories MVS-0 Genius Accessories M8 ables for Sensor B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia.6 (3) (9,7) Dia Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M.96 (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 4 3 able Pin olor Brown White 3 Blue 4 Black MVS-0 ables (nects Sensor to Vacuum & Blow-off Release Pilot Valves) For VK VK-D0G Vacuum Blow-off Valve Vacuum Valve 6" (5 mm) 9" (9 mm) For VR VR-0G Vacuum Valve Vacuum Blow-off Valve For M M-0G Vacuum Blow-off Valve Vacuum Valve Black Blue Parker Hannifin orporati Divisi

22 Features MPS-3 MPS-3 Versatile Panel Mount Features Pressure Ranges: Positive Pressure... 0 to 45 PSI Vacuum Pressure...0 to -30 inhg Low Pressure... 0 to 4.7 PSI ompound to 7.5 PSI Sensor Outputs: NPN or PNP Open ollector Transistor Output, 30VD, 5mA Optial Analog, to 5 VD Switch Point and High-low Programming 4 Selectable Units of Measure (mmhg, -bar, -kpa, inhg) (kgf/cm, PSI, bar, kpa) Automatic Teach Mode Model Number Output Pressure Range MPS-P3N-NG NPN 0 to 45 PSI MPS-P3N-PG PNP 0 to 45 PSI MPS-V3N-NG NPN 0 to -30 inhg MPS-V3N-PG PNP 0 to -30 inhg MPS-P3N-N NPN 0 to 45 PSI MPS-P3N-P PNP 0 to 45 PSI MPS-V3N-N NPN 0 to -30 inhg MPS-V3N-P PNP 0 to -30 inhg Auto Surveillance for Peak Pressure Mitoring Output Respse Time Less Than.0 Millisecds E Marked Air and N-orrosive Gases Error Message Output Modes The MPS-3 Series Sensor has two independent NPN or PNP open collector output signals. An analog output is optial. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. The optial Analog Output Signal is calibrated to the pressure scale of the sensor. Switch Output 0 h off off H -30 in Hg Window omparator Output 0 off A b off -30 in. Hg off Parker Hannifin orporati Divisi

23 Ordering Informati, Specificatis MPS-3 Versatile Panel Mount Model Number Index Bold Items Are Stocked MPS - V 3 N - P Pressure Range V 0 to -30 inhg L 0 to 4.7 PSI P 0 to 45 PSI R -4.7 PSI to 7 PSI Port Size N /8" NPSF R /8" BSPT G /8" BSPP ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector 4-Pin, M8 G Grommet XSH 4-Pin M Analog Output Blank Without A to 5VD MPS-V3N-P MPS-V3N-PG MPS-P3N-PXSH Mounting Bracket MPS-AK Included with Sensors. Specificatis Pressure Range Vacuum (V) Positive (P) ompound (R) Low (L) bar: 0.00 bar: 0.0 bar: 0.0 bar: 0.00 Units of Measure kpa: 0. MPa: 0.00 kpa: kpa: 0. Display Resoluti mmhg: kgf/cm : 0.0 kgf/cm : 0.0 kgf/cm : 0.00 inhg: 0. PSI: PSI: 0. PSI: 0. Media Air and N-orrosive Gases Pressure Port N: /8" NPSF, R: /8" Female BSPT, G: /8" BSPP Female Proof Pressure V: 45 PSI, P: 90 PSI, R: 7 PSI, L: 45 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector, G: Grommet Open Lead, XSH: M, 4-Pin Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Display 3-Digit, 7-Segment LED Display Refresh. to 3.0 sec. (Factory set at 0.) Output ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor, 30VD, 5mA Switch Outputs Output Signals, NPN or PNP, Normally Open or losed, LED Indicator Linear Output Optial Analog Output to 5VD Output Modes Hysteresis or Window omparator Output Respse Time < ms with Programmable Increment 3, 8, 04ms (XSH-3, 56, 5ms) Repeatability ± 0.% F.S. Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP65 or IP 40, E Marked, EM-EN550 lass B, EN urrent sumpti < 55mA Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Housing: Polycarbate, Pressure Port: Zinc Die-cast Mass.58 oz. (45g) 3 Parker Hannifin orporati Divisi

24 Technical Informati MPS-3 Versatile Panel Mount Sensor Pin Out Pin # Brown: 4VD White: NPN / PNP Open ollector Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Sensor Pin Out with Analog Output Pin # Brown: 4VD White: Analog to 5VD 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Lead Wiring Brown V+ White NPN / PNP Output Blue 0V Black NPN / PNP Output Lead Wiring Brown V+ White Analog to 5 VD Blue 0V Black NPN / PNP Output Internal ircuit for Open ollector and Analog Output Wiring Main ircuit D Tr Tr ZD ZD K ZD3 (Brown) +V Max. 5mA (Black) Out Load Load (White) Out Max. 5mA (White) Analog D Opti to 5V (Blue) OV + D 0.8V 30V Main ircuit Tr Tr ZD K D ZD ZD3 (Brown) +V (Black) Out (White) Out + D (White) Analog 0.8V 30V Opti D Load to 5V Max. Max. Load 5mA (Blue) OV 5mA NPN PNP autis! Installati The MPS-3 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install as shown using the metal mounting bracket. To achieve IP65 rating, cnect the o-ring and barb as shown to a normal envirment with a mm I. D. tube. Pipe Plug Ambient Air Inlet Port Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Barb O-Ring oupling INLUDED Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er System Error (Internal) tact Factory Er Auto Teach Mode Error Restart Functi E Over current of Output Load current exceeds E Over current of Output maximum 5mA. FFF Applied pressure exceeds Apply pressures within FF pressure range the rating of the sensor 4 Parker Hannifin orporati Divisi

25 Dimensis MPS-3 Versatile Panel Mount Dimensis N, R, G /8" Female.8 (30).8 (30).06 (7).8 (4,5).33 (8,5) (0).5 (3).8 (30).8 (30) (0).6 (4) Grommet Lead.6 (6,7).6 (4) M8 4-Pin nector.46 (,) N /8 NPT R /8 BSPT G /8 BSPP M3 Venting Port 3 (85,6) M 4-Pin nector MPS-AK Mounting Brackets (Included).55 (4).8 (7).98 (5).3 (5,5).55 (4).06 (7) (0).0 (8) (0).69 (43) (0).8 (30) (0).37 (35).77 Dia (4,5).87 ().4 (6).3 (5,5).77 Dia (4,5).5 (3).5 (3) 5 Parker Hannifin orporati Divisi

26 Programming Features MPS-3 Versatile Panel Mount See page 87 for Symbol Explanati Hold Press x 3 Press x Output Mode Output Set Open Hysteresis or or losed Selecting Window Units of Measure omparator Easy Mode Activati Press 4x Output Mode Hysteresis or Window omparator 4 Press x 5 Press 3x 6 Output Output Switch Point Switch Point Setting Setting Press 5x Automatic Teach Mode & Auto Surveillance Hysteresis Mode Hysteresis Mode Vacuum ycle Window omparator Mode Low Window omparator Mode Low Release ycle High High 7 Press 6x 8 Press 7x 9 Press 8x Display Refresh Display Peak Value Settings / Output Bottom Value or Respse Time Their Difference Interval Special Display Features 0 Hold Press x Hold Press x Press x Press x Press for 3 Secds Zero Reset Lock Unlock Peak Value Bottom Value 6 Parker Hannifin orporati Divisi

27 Accessories MPS-3 Versatile Panel Mount Accessories ables B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia.6 (3) (9,7) Dia Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M.96 (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 4 3 able Pin olor Brown White 3 Blue 4 Black MPS-AH7 Panel Mounting Bracket.7 (43,8).57 (40).57 (40).3 (33,4) Knockout.4 (36) (+0.5, -0.).4 (36) (+0.5, -0.) 7 Parker Hannifin orporati Divisi

28 Features MPS-3 Stainless Steel Model Number Output Pressure Range MPS-P3S5-N NPN 0 to 45 PSI MPS-P3S5-P PNP 0 to 45 PSI MPS-V3F5-NA NPN & Analog 0 to -30 inhg MPS-V3F5-PA PNP & Analog 0 to -30 inhg MPS-P3S5-NA NPN & Analog 0 to 45 PSI MPS-P3S5-PA PNP & Analog 0 to 45 PSI MPS-3 Stainless Steel Features Fluids N-orrosive to Stainless Steel SUS 36L or SUS 630 Air Ammia Brake Fluids Helium Hydraulic Fluids Fres Lubricating Oils Nitrogen Water Pressure Ranges: Positive Pressure... 0 to 45 PSI Vacuum Pressure... 0 to -30 inhg ompound to 7.5 PSI Sensor Outputs: NPN or PNP Open ollector Transistor Outputs, 30VD, 5mA Optial Analog Output, to 5 VD Switch Point and High-low Programming 4 Selectable Units of Measure (mmhg, -bar, -kpa, inhg) (kgf/cm, PSI, bar, kpa) Automatic Teach Mode Auto Surveillance for Peak Pressure Mitoring Output Respse Time Less Than.0 Millisecds E Marked Error Message Output Modes The MPS-3 Stainless Steel Series Sensor has two independent NPN or PNP open collector output signals. An analog output is optial. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. The optial Analog Output Signal is calibrated to the pressure scale of the sensor. Switch Output 0 h off off H -30 in Hg Window omparator Output 0 off A b off -30 in. Hg off 8 Parker Hannifin orporati Divisi

29 Ordering Informati, Specificatis MPS-3 Stainless Steel Model Number Index Bold Items Are Stocked MPS - P3S 5 - P Pressure Range V3F 0 to -30 inhg P3S 0 to 45 PSI R3F -4.7 PSI to 7 PSI Port Size 5 M5F 36SS V V Type 36SS ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector 4-Pin, M8 G Grommet Analog Output Blank Without A to 5VD MPS-P3S5-P MPS-P3S5-NGA MPS-P3SV-NGA Mounting Bracket MPS-AK Included with Sensors. Specificatis Pressure Range Vacuum (V3F) Positive (P3S) ompound (R3F) bar: 0.00 bar: 0.0 bar: 0.0 Units of Measure kpa: 0. MPa: 0.00 kpa: Display Resoluti mmhg: kgf/cm : 0.0 kgf/cm : 0.0 inhg: 0. PSI: PSI: 0. Media Fluids, N-orrosive to 36L or 630 SUS Pressure Port 5: M5F, V: Semi-ductor Type nector Proof Pressure V3F: 45 PSI, P35: 90 PSI, R3F: 7.5 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector, G: Grommet Open Lead Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Display 3-Digit, 7-Segment LED Display Refresh. to 3.0 sec. (Factory set at 0.) Output ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor; 30VD, 5mA Switch Outputs Output Signals, NPN or PNP, Normally Open or losed, LED Indicator Linear Output Optial Analog Output to 5VD Output Modes Hysteresis or Window omparator Output Respse Time < ms with Programmable Increment 3, 8, 04ms Repeatability ± 0.% F.S. Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP 65 or IP 40, E Marked, EM-EN550 lass B, EN urrent sumpti < 55mA Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Housing: Polycarbate, Wetted Parts: P: 36L or V,R: 630 SUS (Diaphragm) Mass 4.4 oz. (0g) 9 Parker Hannifin orporati Divisi

30 Technical Informati MPS-3 Stainless Steel Sensor Pin Out Pin # Brown: 4VD White: NPN / PNP Open ollector Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Sensor Pin-Out with Analog Output Pin # Brown: 4VD White: Analog to 5VD Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Lead Wiring Lead Wiring Brown V+ White NPN / PNP Output Blue 0V Black NPN / PNP Output Brown V+ White Analog to 5 VD Blue 0V Black NPN / PNP Output Internal ircuit for Open ollector and Analog Output Wiring Main ircuit D Tr Tr ZD ZD K ZD3 (Brown) +V Max. 5mA (Black) Out Load Load (White) Out Max. 5mA (White) Analog D Opti to 5V (Blue) OV + D 0.8V 30V Main ircuit Tr Tr ZD K D ZD ZD3 (Brown) +V (Black) Out (White) Out + D (White) Analog 0.8V 30V Opti D Load to 5V Max. Max. Load 5mA (Blue) OV 5mA NPN PNP autis! Depending the system fluid and design, it may be The MPS-3 Stainless Steel Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. necessary to protect the diaphragm against pressure spikes by installing a flow restricti upstream from the sensor. Installati Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting base. To achieve IP65 rating, cnect the o-ring and barb to a normal envirment with a mm I. D. tube. Error Messages Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er System Error (Internal) tact Factory Er Auto Teach Mode Error Restart Functi E Over current of Output Load current exceeds E Over current of Output maximum 5mA. FFF Applied pressure exceeds Apply pressures within FF pressure range the rating of the sensor 30 Parker Hannifin orporati Divisi

31 Dimensis MPS-3 Stainless Steel Dimensis M5 Back & Bottom Ports.8 (30).75 (44,5).39 (0) M3 4 Places (0).8 (30) (0).6 (4) M8 V necti Grommet or M8, 4-Pin 4-Pin nector.46 (,) Grommet Lead M5.6 (6,7).75 (44,5) 3.50 (88,9).39 (0) M3 4 Places (0) M3 Venting Port (0).6 (6,7) MPS-AK Mounting Brackets (Included).55 (4).8 (7).98 (5).3 (5,5).55 (4).06 (7) (0).0 (8) (0).69 (43) (0).8 (30) (0).37 (35).77 Dia (4,5).87 ().4 (6).3 (5,5).77 Dia (4,5).5 (3).5 (3) 3 Parker Hannifin orporati Divisi

32 Programming Features MPS-3 Stainless Steel See page 87 for Symbol Explanati Hold Press x 3 Press x Output Mode Output Set Open Hysteresis or or losed Selecting Window Units of Measure omparator Easy Mode Activati Press 4x Output Mode Hysteresis or Window omparator 4 Press x 5 Press 3x 6 Output Output Switch Point Switch Point Setting Setting Press 5x Automatic Teach Mode & Auto Surveillance Hysteresis Mode Hysteresis Mode Vacuum ycle Window omparator Mode Low Window omparator Mode Low Release ycle High High 7 Press 6x 8 Press 7x 9 Press 8x Display Refresh Display Peak Value Settings / Output Bottom Value or Respse Time Their Difference Interval Special Display Features 0 Hold Press x Hold Press x Press x Press x Press for 3 Secds Zero Reset Lock Unlock Peak Value Bottom Value 3 Parker Hannifin orporati Divisi

33 Accessories MPS-3 Stainless Steel Accessories ables B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia.6 (3) (9,7) Dia Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M.96 (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 4 3 able Pin olor Brown White 3 Blue 4 Black MPS-AH Panel Mounting Bracket.7 (43,8).57 (40).57 (40).3 (33,4) Knockout.4 (36) (+0.5, -0.).4 (36) (+0.5, -0.) 33 Parker Hannifin orporati Divisi

34 Features MPS-3 Red Green Display Model Number Output Pressure Range MPS-P3N-NG NPN 0 to 45 PSI MPS-P3N-PG PNP 0 to 45 PSI MPS-V3N-NG NPN 0 to -30 inhg MPS-V3N-PG PNP 0 to -30 inhg MPS-P3N-I 4 to 0mA 0 to 45 PSI MPS-P3N-N NPN 0 to 45 PSI MPS-P3N-P PNP 0 to 45 PSI MPS-V3N-N NPN 0 to -30 inhg MPS-V3N-P PNP 0 to -30 inhg MPS-3 -olor Panel Mount Features Pressure Ranges: Positive Pressure... 0 to 45 PSI Vacuum Pressure...0 to -30 inhg ompound to 7.5 PSI Sensor Output: NPN or PNP Open ollector Transistor Output, 30VD, 5mA Optial Analog Output, 4 to 0mA Switch Point and High-low Programming 4 Selectable Units of Measure (mmhg, -bar, -kpa, inhg) (kgf/cm, PSI, bar, kpa) Programmable Display olors Output Respse Time Less Than.0 Millisecds E Marked Air and N-orrosive Gases Error Message Output Modes The MPS-3 Series Sensor has e independent NPN or PNP open collector output signal. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. Switch Output 0 h off off H -30 in Hg Window omparator Output 0 off A b off -30 in. Hg off 34 Parker Hannifin orporati Divisi

35 Ordering Informati, Specificatis MPS-3 -olor Panel Mount Model Number Index Bold Items Are Stocked MPS - V 3 N - P Pressure Range V 0 to -30 inhg P 0 to 45 PSI R -4.7 PSI to 7 PSI Port Size N /8" NPSF R /8" BSPT G /8" BSPP Output ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector 4-Pin, M8 G Grommet Analog Output Blank Without I 4 to 0mA urrent MPS-V3N-PG Mounting Bracket MPS-AK Included with Sensors. MPS-V3N-P Specificatis Pressure Range Vacuum (V) Positive (P) ompound (R) bar: 0.00 bar: 0.0 bar: 0.0 Units of Measure kpa: 0. MPa: 0.00 kpa: Display Resoluti mmhg: kgf/cm : 0.0 kgf/cm : 0.0 inhg: 0. PSI: PSI: 0. Media Air and N-orrosive Gases Pressure Port N: /8" NPSF, R: /8" BSPT, G: /8" BSPP Proof Pressure V: 45 PSI, P: 7.5 PSI, R: 45 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector, G: Grommet Open Lead Power Supply 0.8 to 6.4VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Display 3-Digit, 7-Segment LED Display Refresh. to 3.0 sec. (Factory set at 0.) Output ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor, 30VD, 5mA Switch Output Output Signal, NPN or PNP, Normally Open or losed, LED Indicator Output Modes Hysteresis or Window omparator Output Respse Time < ms, 3, 56, 5ms Programmable (Factory set ms) Repeatability ± 0.% F.S. Output urrent: 4 to 0mA Analog urrent Linearity: ±0.5% F.S. or less Output Output Maximum Load Impedance: 300Ω with power supply voltage of V; 600Ω with power supply voltage of V; Minimum Load Impedance: 50Ω Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP40, E Marked, EM-EN550 lass B, EN urrent sumpti < 70mA Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Housing: Polycarbate, Pressure Port: Zinc Die-cast Mass.7 oz. (45g) 35 Parker Hannifin orporati Divisi

36 (Revised 0/3/04) Technical Informati MPS-3 -olor Panel Mount Sensor Pin Out Pin # Brown: 4VD White: Not Used 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Sensor Pin Out with Analog Output Pin # Brown: 4VD White: 4 to 0mA 3 Blue: 0VD 4 Black: NPN / PNP Open 3 4 Lead Wiring Brown V+ Black NPN / PNP Output Blue 0V Lead Wiring Brown V+ White 4 to 0 ma Blue 0V Black NPN / PNP Output Internal ircuit for Open ollector and Analog Output Wiring Main ircuit D Tr Tr ZD ZD K ZD3 (Brown) +V Max. 5mA (White) Analog Load (Black) Out Max. 5mA (Blue) OV + D 0.8V 30V Main ircuit Tr Tr ZD K D ZD ZD3 (Brown) +V (White) Analog (Black) Out Max. Load (Blue) OV 5mA + D 0.8V 30V NPN PNP autis! Installati The MPS-3 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install as shown using the metal mounting bracket. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er System Error (Internal) tact Factory E Over current of Output Load current exceeds FFF Applied pressure exceeds Apply pressures within FF pressure range the rating of the sensor 36 Parker Hannifin orporati Divisi

37 Dimensis MPS-3 -olor Panel Mount Dimensis N, R, G /8" Female.8 (30).06 (7).8 (4,5).33 (8,5) (0).5 (3).8 (30) (0) Grommet Lead.6 (6,7).6 (4) M8 4-Pin nector.46 (,) N /8 NPT R /8 BSPT G /8 BSPP M3 Venting Port MPS-AK Mounting Brackets (Included).55 (4).8 (7).98 (5).3 (5,5).55 (4).06 (7) (0).0 (8) (0).69 (43) (0).8 (30) (0).37 (35).77 Dia (4,5).87 ().4 (6).3 (5,5).77 Dia (4,5).5 (3).5 (3) 37 Parker Hannifin orporati Divisi

38 Programming Features MPS-3 -olor Panel Mount See page 87 for Symbol Explanati Press for 3 Secds Begin Programming Operating Output Mode Output Normally Open or losed Select Units of Measure Or Press x to Proceed Or Press x to Proceed Or Press x to Proceed Wait 3 Secds Wait 3 Secds Wait 3 Secds Display Refresh Output Respse Selecti Display olor hoices Red and / or Green, Energy Save Or Press x to Proceed Or Press x to Proceed Or Press x to Return Wait 3 Secds Wait 3 Secds Wait 3 Secds Output On Off Red Green Green Red Green Red Red Green Press x 3 Press x Switch Output Setting and Low Setting Hysteresis Setting and High Setting 4 Hold Press x Hold Press x Will Display for Secd Hysteresis Mode Will Display for Secd Hysteresis Mode Lock Unlock Window omparator Mode Window omparator Mode 5 Zero Reset Low High Wait 5 Secds Wait 5 Secds Press for3 Sec. 38 Parker Hannifin orporati Divisi

39 Accessories MPS-3 -olor Panel Mount Accessories ables B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia.6 (3) (9,7) Dia Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M.96 (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 4 3 able Pin olor Brown White 3 Blue 4 Black MPS-AH7 Panel Mounting Bracket.7 (43,8).57 (40).57 (40).3 (33,4) Knockout.4 (36) (+0.5, -0.).4 (36) (+0.5, -0.) 39 Parker Hannifin orporati Divisi

40 Features / omm Part Numbers MPS-4 Differential MPS-4 Sensitive Features Pressure Ranges: Positive Pressure to 8 inh O Vacuum Pressure... 0 to -9.8 inhg Sensor Outputs: NPN or PNP Open ollector Transistor Output, 30VD, 5mA Optial Analog Output, to 5 VD Switch Point and High-low Programming Selectable Units of Measure Output Respse Time Less Than.5 Millisecds E Marked Air and N-orrosive Gases Model Number Output Pressure Range MPS-D4M5-N NPN -8 to +8 inh O MPS-D4M5-P PNP -8 to +8 inh O Dual Ports for Reference Pressure Output Modes The MPS-4 Differential Pressure Sensor mitors pressure in applicatis where small changes in pressure are critical. The MPS-4 has two independent NPN or PNP open collector output signals. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (H) settings which are programmed the sensor by the user. The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. The optial Analog Output Signal is calibrated to the pressure scale of the sensor. Switch Output 0 h off off H -30 in Hg Window omparator Output 0 off A b off -30 in. Hg off 40 Parker Hannifin orporati Divisi

41 Ordering Informati, Specificatis Differential MPS-4 Sensitive Model Number Index Bold Items Are Stocked MPS - D 4 M5 - P - Pressure Range D -8 inh O to 8 inh 0 V 0 to -9.8 inhg Port M5 M5 Port Output ircuit N NPN Sinking P PNP Sourcing Electrical nector 4-Pin, M8 G Grommet Optial Output Blank Without A Analog ( to 5VD) Mounting Bracket MPS-AK Included with Sensors. MPS-D4M5-P Specificatis Media Air and N-orrosive Gases Pressure Port M5 Female ( qty.) Proof Pressure V: 9 PSI, D: 3.9 Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti G: Grommet Lead, : 4-Pin, M8 nector Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Display 3-Digit, 7-Segment LED Resoluti & Units of Measure kpa: 0.0, mmh O:, inh O: 0., inhg: 0. Display Refresh. to 3.0 sec. (Factory set at 0.) Output ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor, 30VD, 5mA Switch Outputs Output Signals, Normally Open or losed, LED Indicator Linear Output Optial Analog Output -5VD, ± 0.% Linear Accuracy 0.5% F.S. Output Modes Hysteresis or Window omparator Output Respse Time D: <.5ms Repeatability D: < ± 0.5% F.S. Thermal Error Max. ±3% F.S. in Temperature Range: 3 to F (0 to 50 ) General Protecti IP40, E Marked, EM Rating: EN550 lass B, EN5008- urrent sumpti < 45mA Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Housing: Polycarbate, Pressure Port: Anodized Aluminum Mass.6 oz. (45g) 4 Parker Hannifin orporati Divisi

42 Technical Informati Differential MPS-4 Sensitive Sensor Pin Out Pin # Brown: 4VD White: NPN / PNP Open ollector Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Sensor Pin-Out with Analog Output Pin # Brown: 4VD White: Analog to 5VD Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Lead Wiring Lead Wiring Brown V+ Brown V+ White NPN / PNP Output White Analog to 5 VD Blue 0V Blue 0V Black NPN / PNP Output Black NPN / PNP Output Internal ircuit for Open ollector and Analog Output Wiring Main ircuit D Tr Tr ZD ZD K ZD3 (Brown) +V Max. 5mA (Black) Out Load Load (White) Out Max. 5mA (White) Analog D Opti to 5V (Blue) OV + D 0.8V 30V Main ircuit Tr Tr ZD K D ZD ZD3 (Brown) +V (Black) Out (White) Out + D (White) Analog 0.8V 30V Opti D Load to 5V Max. Max. Load 5mA (Blue) OV 5mA NPN PNP autis! Installati The MPS-4 Differential Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting bracket. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er System Error (Internal) tact Factory E Over current of Output Load current exceeds E Over current of Output maximum 5mA. FFF Applied pressure exceeds Apply pressures with FF pressure range the rating of the sensor 4 Parker Hannifin orporati Divisi

43 Dimensis Differential MPS-4 Sensitive Dimensis M5 Female.8 (30).8 (30).39 (0).75 (44,5).96 (4,5).39 (0) (0).33 (8,5).8 (30).8 (30) (0).47 () A M5-6,5.6 (4) M8.46 (,) M3 4 Places B M5-6,5 4-Pin nector Grommet Lead MPS-AK Mounting Brackets (Included).55 (4).8 (7).98 (5).3 (5,5).55 (4).06 (7) (0).0 (8) (0).69 (43) (0).8 (30) (0).37 (35).77 Dia (4,5).87 ().4 (6).3 (5,5).77 Dia (4,5).5 (3).5 (3) 43 Parker Hannifin orporati Divisi

44 Programming Features Differential MPS-4 Sensitive See page 87 for Symbol Explanati Hold Press x 3 Press 4x Press x Output Mode Output Set Open Hysteresis or or losed Selecting Window omparator Units of Measure Output Mode Hysteresis or Window omparator 4 Press x 5 Press 3x 6 Press 5x Output Output Switch Point Switch Point Setting Setting Hysteresis Mode Hysteresis Mode Port Reference Selecti A Port B Port Window omparator Mode Low Window omparator Mode Low 9 Hold Press x Hold Press x High High Lock Unlock 7 Press 6x 8 Press 7x Display Refresh Settings / Output Respse Time Interval Display Peak Value Bottom Value or Their Difference 0 Press x Press x Peak Value Bottom Value Hold for 3 Secds Zero Reset 44 Parker Hannifin orporati Divisi

45 Accessories Differential MPS-4 Sensitive Accessories ables B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia.6 (3) (9,7) Dia Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M.96 (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 4 3 able Pin olor Brown White 3 Blue 4 Black MPS-AH Panel Mounting Bracket.7 (43,8).57 (40).57 (40).3 (33,4) Knockout.4 (36) (+0.5, -0.).4 (36) (+0.5, -0.) 45 Parker Hannifin orporati Divisi

46 Features / omm Part Numbers MPS-5 Stainless Pressure Transducer MPS-5 Stainless Steel Features Pressure Ranges: Positive Pressure... 0 to 45 PSI Vacuum Pressure...0 to -30 inhg Sensor Output: to 5 VD Analog Output Output (Volts) Max. Rating Pressure Model Number Output Pressure Range MPS-P5N-A Analog 0 to 45 PSI MPS-P5N-AG Analog 0 to 45 PSI MPS-P5N-AGE Analog 0 to 45 PSI MPS-V5FN-A Analog 0 to -30 inhg MPS-V5FN-AG Analog 0 to -30 inhg MPS-V5FN-AGE Analog 0 to -30 inhg 36L SUS Diaphragm (Positive) 630 SUS Diaphragm (Vacuum) ompatible with MPS-7 Display for Remote Sensing E Marked The MPS-5 Series Transducer is cstructed of 36L or 630 SUS with Analog output capabilities. The sensor can be used as a stand ale unit or in combinati with the MPS-7 Sensor Display. The analog output is to 5VD (± 0.04) with accuracy linear 0.5% F.S. 46 Parker Hannifin orporati Divisi

47 Ordering Informati, Specificatis Pressure Transducer MPS-5 Stainless Steel Model Number Index Bold Items Are Stocked MPS - V5F N - A G Pressure Range V5F 0 to -30 inhg P5 0 to 45 PSI R N Port Size /4" BSPT Male, M5F /4" NPT Male, M5F Output ircuit A Analog to 5VD Electrical nector 4-Pin, M8 G Grommet GE m Grommet lip n.* *Use with MPS-7 Series Display MPS-V5FN-A MPS-V5FN-AG MPS-V5FN-AGE Specificatis Media Liquids and Gases N-orrosive to 36SS Pressure Port R: /4" Male BSPT, N: /4" Male NPT with M5 Female Proof Pressure V: 45 PSI, P: 90 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector, G: Grommet Open Lead, GE: lip Type for use with MPS-7 Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Linear Output Analog Output to 5VD Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP65, E Marked, EM Rating: EN550 lass B, EN5008- urrent sumpti < 0mA Spike Protecti 400 VP, µs Dielectric Strength 000VA, min. Insulati Resistance > 00M ohms at 500VD Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Housing: 303SUS, Wetted Parts: P5: 36L SUS, V5F: 630 SUS (Diaphragm) Mass 3.88 oz. (0g) 47 Parker Hannifin orporati Divisi

48 Technical Informati Pressure Transducer MPS-5 Stainless Steel Sensor Pin Out Pin # Brown: 4VD Black: Analog -5VD 3 Blue: 0VD 4 Not Used 3 4 Lead Wiring Brown V+ White Output Blue 0V Black Not Used Internal ircuit (Brown) +V Main ircuit (Black) Analog to 5V Output + D - 0.8V to 30V (Blue) OV Analog! autis The MPS-5 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Depending the system fluid and design, it may be necessary to protect the diaphragm against pressure spikes by installing a flow restricti upstream from the sensor. Installati Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting base. To achieve IP65 rating, cnect the o-ring and barb to a normal envirment with a mm I. D. tube. Ambient Air Inlet Port Barb O-Ring oupling INLUDED 48 Parker Hannifin orporati Divisi

49 Dimensis Pressure Transducer MPS-5 Stainless Steel Dimensis N, R /4" Male Grommet.06 (7).59 (5).59 (40,5).06 (7) Dia. M5 x,0 N, R /4" Male Grommet lip nector /4" NPT (BSPT).0 (5,).06 (7).59 (5).59 (40,5).06 (7) Dia. Shield nector (AMP) Housing (AMP) 78-5 M5 x,0 /4" NPT (BSPT).0 (5,) N, R /4" Male 4-Pin, M8 nector.06 (7).59 (5).59 (40,5) M8.06 (7) Dia. M5 x,0 /4" NPT (BSPT).46 (,) 49 Parker Hannifin orporati Divisi

50 Accessories Pressure Transducer MPS-5 Stainless Steel Accessories ables B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3).96 (5) Dia.6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia 6.40 ft (5m).87 () (9,7) Dia.75.4 (9) (0,7) (9,7) Dia B-M8-4P-E, M8 Female Female Interface 4-Pin, M8.96 (5) Dia Housing (AMP) 78-5 Shield Male Interface 4-Pin, M8 Male Interface 4-Pin, M nector (AMP) (7) able Pin olor Brown White 3 Blue 4 Black 50 Parker Hannifin orporati Divisi

51 Notes Pressure Transducer MPS-5 Stainless Steel 5 Parker Hannifin orporati Divisi

52 Features MPS-6 Model Number Output Pressure Range MPS-P6N-N NPN 0 to 45 PSI MPS-P6N-P PNP 0 to 45 PSI MPS-P6N-AG Analog 0 to 45 PSI MPS-P6N-AGE Analog 0 to 45 PSI MPS-V6N-N NPN 0 to -30 inhg MPS-V6N-P PNP 0 to -30 inhg MPS-V6N-AG Analog 0 to -30 inhg MPS-V6N-AGE Analog 0 to -30 inhg MPS-6 ompact Features Pressure Ranges: Positive Pressure...0 to 45 PSI Vacuum Pressure... 0 to -30 inhg Sensor Outputs: Open and losed NPN or PNP Open ollector Transistor Output, 30VD, 5mA Analog Output, to 5 VD Switch Point /3 Trimmer Fixed Hysteresis % Output Respse Time Less Than Millisecd Analog Output Type ompatible with MPS-7 Display E Marked Air and N-orrosive Gases Output Modes The MPS-6 Series Sensor is compact and lightweight with NPN or PNP open cnector switch output or analog output capabilities. The sensor can be used as a stand ale unit or in combinati with the MPS-7 series display. The MPS-6 Switch Output unit provides e open and closed output for the same switch point. The MPS-6 Analog Output unit provides analog output to 5VD. Analog output is required for use with the MPS-7 display. Switch Output S Fixed % off off Output (Volts) 0-30 in Hg Analog Output Max. Rating Pressure 5 Parker Hannifin orporati Divisi

53 Ordering Informati, Specificatis MPS-6 ompact Model Number Index Bold Items Are Stocked MPS - V 6 N - P Pressure Range V 0 to -30 inhg P 0 to 45 PSIG Port Size N /8" NPT & M5 Female R /8" BSPT & M5 Female G /8" BSPP & M5 Female T 6mm Tube Stud Ejector Output ircuit N NPN Output P PNPOutput A Analog ( to 5VD) Electrical nector 4-Pin, M8 G Grommet GE m Grommet lip n.* * Use with MPS-7 Series Display, Analog Output Only. MPS-P6N-A MPS-P6N-AG MPS-V6T-PG MPS-P6N-AGE Specificatis Media Air and N-orrosives Gases Pressure Port N: /8" NPT Male, R: /8" BSPT Male, G: /8" BSPP Male, T: 6mm Tube Stud Proof Pressure V: 7.5 PSI, P: 7.5 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector G: Grommet Lead GE: lip Type for use with MPS-7 Display Power Supply 0.8 to 30 VD, Ripple Vp-p 0% max., Reverse Voltage Protecti Switch Output Output Signal Open and losed, NPN or PNP, 30VD, 5mA Linear Output Analog Output to 5 VD Switch Point Setting /3 Turn Trimmer Hysteresis Setting < % of F.S. Output Respse Time <ms Repeatability <0.% F.S. Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP40, E Marked, EN550 lass B, EN5008- urrent sumpti < 0mA Spike Protecti 400 VP, µs, Surge Protecti Dielectric Strength 000VA, min. Insulati Resistance > 00M ohm at 500VD Vibrati Resistance 0 to 55Hz, 0.75mm Amplitude, XYZ, hrs. Shock Resistance 00 G, XYZ Material Housing: Polycarbate, Pressure Port: Zinc Die-cast Mass T Port: 0.5 oz. (7g), N, R, G Port: 0.88 oz. (5g) 53 Parker Hannifin orporati Divisi

54 Technical Informati MPS-6 ompact Sensor Pin Out Pin # Brown: 4VD White: NPN / PNP Open ollector Output 3 Blue: 0VD 4 Black: NPN / PNP Open ollector Output 3 4 Sensor Pin Out with Analog Output Pin # Brown: 4VD White: LED In 5VD 3 Blue: 0VD 4 Black: Analog to 5VD 3 4 Internal ircuit D (Brown) +V Main ircuit Tr Tr ZD (Black) Out (N.O.) LOAD Max. 5mA ZD (White) Out (N..) LOAD Max. 5mA (Blue) OV + D 0.8V to 30V NPN Open ollector (Brown) +V D (Brown) +V Main ircuit LED (White) Input for LED lighting (5VD) (Black) Analog 5V Output (Blue) OV + D - 0.8V to 30V Main ircuit Tr Tr ZD (Black) Out (N.O.) LOAD Max. 5mA ZD (White) Out (N..) LOAD Max. 5mA (Blue) OV + D 0.8V to 30V Analog PNP Open ollector! autis! Installati The MPS-6 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Trimmer Adjustment Rotate the potentiometer trimmer to increase or decrease pressure switch point output. Excessive force or exceeding the limits of the trimmers may cause damage. Switch Point Trimmer + 54 Parker Hannifin orporati Divisi

55 Dimensis MPS-6 ompact Dimensis N, R, G /8" Male, M5 Female, Grommet (0).63 (6) R/8, G/8, or /8" NPT M (6,3).39 (0) Switch Point Trimmer Output LED Output LED or T6 Tube Stud, Grommet (0).63 (6) 6mm Tube.34 (34,).78 (9.8).39 (0) Switch Point Trimmer Output LED Output LED or Ejector Mount (0).63 (6).4 (3,5). (3).5 (3).39 (0) Switch Point Trimmer Output LED Output LED or N, R, G /8" Male, M5 Female, M8, 4-Pin (0).63 (6) R/8, G/8, or /8" NPT M (6,3) Switch Point Trimmer Output LED.59 (5) Output LED or T6 Tube Stud, M8, 4-Pin (0).63 (6) 6mm Tube.34 (34,).78 (9.8) Switch Point Trimmer Output LED.59 (5) Output LED or Ejector Mount (0).63 (6).4 (3,5). (3).5 (3) Switch Point Trimmer Output LED.59 (5) Output LED or N, R, G Grommet lip nector (0).63 (6) R/8, G/8, or /8" NPT M (6,3) AMP 5-Pin nector 78-5 Output LED T6 Grommet lip nector (0).63 (6) 6mm Tube.34 (34,).78 (9.8) AMP 5-Pin nector 78-5 Output LED Ejector Mount (0).63 (6).4 (3,5). (3).5 (3) AMP 5-Pin nector 78-5 Output LED 55 Parker Hannifin orporati Divisi

56 Accessories MPS-6 ompact Accessories ables B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3).96 (5) Dia.6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia 6.40 ft (5m).87 () (9,7) Dia.75.4 (9) (0,7) (9,7) Dia B-M8-4P-E, M8 Female Female Interface 4-Pin, M8.96 (5) Dia Housing (AMP) 78-5 Shield Male Interface 4-Pin, M8 Male Interface 4-Pin, M nector (AMP) (7) able Pin olor Brown White 3 Blue 4 Black 56 Parker Hannifin orporati Divisi

57 Notes MPS-6 ompact 57 Parker Hannifin orporati Divisi

58 Features MPS-7 Multi- MPS-7 Display Features One Display with Output Programming apability for MPS-5, 6, or 8 Analog Sensors Displays Pressure and verts Analog Signal from Remote Sensor to NPN or PNP Open ollector Transistor Output, 30VD, 5mA ompatible with to 4 Remote Sensors MPS-7 Respse Time Less Than.0 Millisecds Automatic Teach Mode and Auto Surveillance for Peak Pressure Mitoring MPS-74 Respse Time Less Than 5 Millisecds Auto Surveillance for Peak Pressure Mitoring E Marked MPS-7E-PG trol with Remote MPS-P6N-AGE Shown Output Modes The MPS-7 is a central display and ctrol for remote MPS-5, 6, 8 analog sensors. Each remote sensor supplies an analog signal to a specific channel the MPS-7 which is cverted to an open cnector output NPN / PNP. The Switch Output Mode has a switch point programmed by the user at a specified pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. Model Number MPS-7E-N MPS-7E-P MPS-7E-NG MPS-7E-PG MPS-74E-NG MPS-74E-PG Switch Output 0 h off off H -30 in Hg Window omparator Output 0 off A b off -30 in. Hg Output NPN PNP NPN PNP NPN PNP off 58 Parker Hannifin orporati Divisi

59 (Revised 0/3/04) Ordering Informati, Specificatis Multi- MPS-7 Display Model Number Index Bold Items Are Stocked MPS - 7 E - N - Number of Remote Sensors Sensor 4 4 Sensors ircuit N NPN Output Sinking P PNP Output Sourcing Electrical nector * 4-Pin, M8 G Grommet * Available MPS-7 ly. Input / Output Optis Blank Without D* Remote Zero Reset A* Analog Output * Available MPS-7 with Grommet Electrical nector Only. MPS-7E-P Mounting Bracket Included with Sensors. MPS-74E-NG Specificatis Remote Pressure Range Vacuum (V) Positive (P) ompound (R) Low (L) bar: 0.00 bar: 0.0 bar: 0.0 bar: 0.00 Units of Measure kpa: 0. MPa: 0.00 kpa: kpa: 0. Display Resoluti mmhg: kgf/cm : 0.0 kgf/cm : 0.0 kgf/cm : 0.00 inhg: 0. PSI: PSI: 0. PSI: 0. Proof Pressure See Remote Sensor Specificatis Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti G: Grommet Open Lead, : M8 nector Power Supply 0.8 to 30VD, Ripple (P-P) 0% Max., Reverse Voltage Protecti Display MPS-7: 3-Digit, 7-Segment LED, MPS-74: 4-Digit, 7-Segment LED Display Refresh MPS-7: 0. to 3.0 sec. (Factory set at 0.), MPS-74: 0. Fixed ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor, 30VD, 5mA 74 - Switch Output 7 - Switch Outputs Output Signals, NPN or PNP, LED Indicator Linear Output Mode (7 Series) Optial Output - Analog -5VD, ± 0.% Linear Accuracy, 0.5% F.S Respse Time MPS-7 <ms, MPS-74 <5ms Repeatability ± 0.% F.S. Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP40, E Marked urrent sumpti MPS-7 <45mA, MPS-74 <75mA Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Body: Polycarbate Mass MPS-7:.90 oz. (5g), MPS-74:.0 oz. (30g) 59 Parker Hannifin orporati Divisi

60 Technical Informati Multi- MPS-7 Display MPS-7 Open ollector MPS-7 Open ollector with Analog or MPS-74 Open ollector Wiring Reset Input Wiring Pin # Grommet Lead Only Grommet Lead Only Brown: 4VD Brown: 4VD Brown: 4VD Black: NPN / PNP Open ollector Black: NPN / PNP Open ollector Black: NPN / PNP Open ollector 3 Blue: 0VD Blue: 0VD Blue: 0VD 4 White: NPN / PNP Open ollector White: NPN / PNP Open ollector White: NPN / PNP Open ollector Sensor Male Pin Out 3 4 Pink: Analog to 5VD or Reset Pink: NPN / PNP Open ollector Input to 5VD Orange:NPN / PNP Open ollector Brown V+ Blue 0V Black NPN / PNP Open ollector White NPN / PNP Open ollector Pink NPN / PNP Open ollector Orange NPN / PNP Open ollector Internal ircuit Main ircuit Tr Tr ZD K ZD3 D ZD (Brown) +V (Black) Out (White) Out (Pink) Analog Opti D to 5V (Blue) OV Load Max. 5mA Load + D 0.8V to 30V (Brown) +V (Black) Out PNP Open ollector Analog Out D (Brown) +V Main ircuit (White) Out (Pink) Out 3 (74E) (Orange) Out 4 (74E) (Blue) OV Main ircuit Tr Tr ZD ZD (Black) Out (White) Out (Pink) Digital IN Opti (Blue) OV Max. 5mA Max. 5mA Load Or Tr Load + D 0.8V to 30V MPS-7 & MPS-74 NPN / PNP Open ollector PNP Open ollector Reset In autis! Installati The MPS-7 entral Display is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Operatis Dedicate a power supply of 0.8 to 30VD to the MPS-7 Series and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Avoid short-circuiting the MPS-7 Series. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using Panel Mount Bracket or Back Mount Brackets. Error Messages Display Descripti Solutis Err Zero Reset Error Reset Zero PErr Peak Value Error heck Vacuum Source Reset: Press Mode Key Er System Error (Internal) tact Factory E Over current of Output E Over current of Output Load current exceeds E3 Over current of Output 3 (MPS-74) maximum 5mA. E4 Over current of Output 4 (MPS-74) FFF Applied pressure exceeds Apply pressures within FF pressure range the rating of the sensor 60 Parker Hannifin orporati Divisi

61 Dimensis Multi- MPS-7 Display Dimensis MPS-7.8 (30).4 (9) - M3 (0).0 (5).8 (30).65 (6,5) AMP EI 5-Pin nector MPS-AK Mounting Bracket (Included).8 (7).55 (4).98 (5).06 (7) (0).3 (5,5).77 Dia (4,5).55 (4).0 (8) (0).77 Dia (4,5).69 (43) (0).8 (30) (0).37 (35).87 ().4 (6).3 (5,5).5 (3).5 (3) MPS (40).98 (5).4 (0,5) AMP EI 5-Pin nector H H H H (40) 3 4 H H (5) H-4 H Reset IN (5) - M3 - M3 MPS-AK3 Mounting Bracket (Included).3 (5,5).98 (5).8 (30).8 (7).77 Dia (4,5) Dia (3,5).8 (30).3 (5,5).8 (30) (0).8 (30).4 (6) Dia (3,5).77 Dia (4,5).8 (30).0 (6) 79 (0).46 (37).87 ().50 (38).57 (4,6) 6 Parker Hannifin orporati Divisi

62 MPS7 Series Programming Features Multi- MPS-7 Display See page 87 for Symbol Explanati Hold Press x Output Set Open or losed Easy Mode Activati Press x 3 Press 4x Output Mode Hysteresis or Window omparator Output Mode Hysteresis or Window omparator 4 Press x 5 Press 3x 6 Press 5x Output Switch Point Setting Output Switch Point Setting Hysteresis Mode Hysteresis Mode Automatic Teach Mode & Auto Surveillance Vacuum ycle Window omparator Mode Low Window omparator Mode Low Release ycle High High 7 Press 6x 8 Press 7x 9 Press 8x Display Refresh Settings / Output Respse Time Display Peak Value Bottom Value or Their Difference Interval Special Display Features 0 Press 9x Hold Hold Press x Press x 3 Press Select Press x Press x Units of Measure 3 Sec Select Pressure Lock Unlock Peak Value Bottom Value Zero Reset Vacuum Low Pressure Positive Pressure ompound Pressure 6 Parker Hannifin orporati Divisi

63 MPS74 Series Programming Features Multi- MPS-7 Display Hold Press x 3 4 Output Selecti Normally Open / Normally losed Press x 3 4 Select Output Mode Hysteresis or Window omparator Output Setting Peak Surveillance (Repeat Procedure for Each hannel) Hysteresis Mode Window omparator Mode Low High 3 Press x 4 Select Remote Pressure Select Unit of Measure 3 4 Press 3x 3 4 Energy Saving Mode Digital IN Mode (Remote Zero Reset) Vacuum Low Pressure Standard Pressure ompound Pressure 5 Press and Hold 3 Secds 6 Scan Mode Press x to Deactivate Hold Press x Hold Press x Lock Unlock 3 Secd Intervals 63 Parker Hannifin orporati Divisi

64 Accessories Multi- MPS-7 Display Accessories ables (Applicable to MPS-7E Display Units Only) B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3) B-M8-4P-5M-90, Female to Open Lead.96 (5) Dia.6 (3) (9,7) Dia Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M.96 (5) Dia 6.40 ft (5m).87 ().75.4 (9) (0,7) 4 3 able Pin olor Brown White 3 Blue 4 Black Parker Hannifin orporati Divisi

65 Accessories Multi- MPS-7 Display Accessories MPS-AH4 Panel Mounting Bracket for MPS-7.7 (43,8).57 (40).57 (40).3 (33,4) Knockout.4 (36) (+0.5, -0.).4 (36) (+0.5, -0.) MPS-AH5 Panel Mounting Bracket for MPS-74.0 (53.8).97 (50).97 (50) 3 4 Knockout.8 (46) (+0.5, -0.).8 (46) (+0.5, -0.) 65 Parker Hannifin orporati Divisi

66 Features MPS-8 Transducer and Sensor MPS-8 Mini Features Pressure Ranges: Vacuum Pressure...0 to -30 inhg ompound to 7.5 PSI Sensor Outputs: NPN / PNP Open ollector Transistor Output, 30VD, 5mA Analog Output, to 5VD Switch Point /3 Trimmer Adjustment Fixed Hysteresis % 0mm Wide ompatible with MPS-7 Display E Marked Air and N-orrosive Gases Model Number Output Pressure Range MPS-V8B-NG NPN 0 to -30 inhg MPS-V8B-PG PNP 0 to -30 inhg MPS-V8U-AG Analog 0 to -30 inhg MPS-V8U-AGE Analog 0 to -30 inhg MPS-R8B-NG NPN -4.7 to 7.5 PSI MPS-R8B-PG PNP -4.7 to 7.5 PSI MPS-R8U-AG Analog -4.7 to 7.5 PSI MPS-R8U-AGE Analog -4.7 to 7.5 PSI Output Mode The MPS-8 Sensor is 0 mm wide with an NPN / PNP open collector switch output or an analog output. The MPS-8 can be used in combinati with the MPS-7 series display or as a stand ale unit. Analog output is required for use with the MPS-7 display. Switch Output S 0-30 in Hg Fixed % off off Analog Output Output (Volts) Max. Rating Pressure 66 Parker Hannifin orporati Divisi

67 Ordering Informati, Specificatis Transducer and Sensor MPS-8 Mini Model Number Index Bold Items Are Stocked MPS - V 8 B - A G Pressure Range V 0 to -30 inhg R** -4.7 PSI to 7.5 PSI **Analog Output ircuit Only A B U T Port Size M5 Through Female M5 Through Female (With Mtg.) M5 Bottom Female M5 Bottom Swivel Male 4mm Tube Stud Output ircuit A Analog (-5VD) N NPN Sinking Output P PNP Sourcing Output nector / able G Grommet GE m Grommet lip n.* * Use with MPS-7 Series Display, Analog Output Only. Specificatis Media Air and N-orrosive Gases Pressure Port M5 Female, M5 Male Swivel, 4mm Tube Stud Proof Pressure V: 7.5 PSI, R: 6 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti G: Grommet Open Lead; GE: lip Type for use with MPS-7 Series Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Switch Output Output, Normally Open, NPN or PNP Open ollector Transistor, 30VD, 5mA Linear Output Analog Output to 5VD Switch Point Setting /3 Trimmer Hysteresis < % of F.S. Fixed Respse Time <ms Repeatability < 0.% F.S. Thermal Error % over ±5 (77 ) Temperature hange (Range 3 to F (0 to 50 ) General Protecti IP40, E Marked, EM rating: EN550 lass B, EN5008- urrent sumpti < 0mA Spike Protecti Vp-p 400v, 0.5ms Surge Protecti Dielectric Strength 000VA, min. Insulati Resistance > 00M ohms at 500VD Vibrati Resistance 0 to 55Hz,.5mm amplitude, XYZ, hrs. Shock Resistance 00 G, XYZ Material Body: Polycarbate; Pressure Port: Anodized Aluminum Mass 0.4 oz. (4g) 67 Parker Hannifin orporati Divisi

68 Technical Informati Transducer and Sensor MPS-8 Mini Open ollector Wiring Analog Wiring Grommet Lead Only Grommet Lead Only Brown: 4VD Brown: 4VD Blue: 0VD Blue: 0VD Black: NPN / PNP Open ollector Black: Analog to 5VD Internal ircuit D (Brown) +V D (Brown) +V Main ircuit Tr ZD (Black) Out LOAD Max. 5mA (Blue) OV + D - 0.8V to 30V Main ircuit Tr ZD (Black) Out (N.O.) LOAD Max. 5mA (Blue) OV + D - 0.8V to 30V NPN Open ollector PNP Open ollector (Brown) +V Main ircuit (Black) Analog to 5V Output + D - 0.8V to 30V (Blue) OV Analog autis! Installati The MPS-8 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting base. 68 Parker Hannifin orporati Divisi

69 Dimensis Transducer and Sensor MPS-8 Mini Dimensis MPS-8A M5 Female, Grommet MPS-8B M5 Female, Grommet.63 (6).39 (0).3 (8) MPS-8 M5 Female, Grommet M5-6 M5-6 (0).9 (4,75).83 ().39 (0).3 (8) M5-6. (3) MPS-8T 4mm Tube Stud.39 (0) (0) M5-6.4 (3,5) Dia. -Places.9 (4,75).63 (6).3 (8).83 ().35 (9).39 (0).6 (4).55 (4) (0).3 (3,) Dia. -Places.9 (4,75).6 Dia. Ø (4) (0).9 (4,75) M (0) MPS-8U M5 Male Swivel, Grommet.4.8 (0,5) (0,9).3 (8).6 (4) M5 (0).9 (4,75) Swivel Joint for Manifold Mount.39 (0).3 (8) Grommet lip nector (Available for All Models) Shield nector (AMP) Housing (AMP) Parker Hannifin orporati Divisi

70 Features MPS-9 Pressure Sensor MPS-9 Thin Features Pressure Ranges: Vacuum Pressure... 0 to -30 inhg ompound to 7.5 PSI Switch Output: NPN or PNP Open ollector, 30VD, 5mA Switch Point Analog Output, to 5VD Switch Point Programming Adjustable Hysteresis Output Respse Time Less Than.5 Millisecds E Marked Air and N-orrosive Gases Model Number Output Pressure Range MPS-V9M-NGA MPS-V9M-PGA MPS-R9M-NGA MPS-R9M-PGA NPN & Analog PNP & Analog NPN & Analog PNP & Analog 0 to -30 inhg 0 to -30 inhg -4.7 PSI to 7.5 PSI -4.7 PSI to 7.5 PSI Output Modes The MPS-9 Sensor with display has e normally open NPN / PNP open collector output and Analog to 5 VD Output. Switch Output 0 The Switch Output Mode has a switch point (H) programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the switch point (H). h off H -30 in Hg Analog Output off 5 Output (Volts) 0 0 Max. Rating Pressure 70 Parker Hannifin orporati Divisi

71 Ordering Informati, Specificatis Pressure Sensor MPS-9 Thin Model Number Index Bold Items Are Stocked MPS - V 9 M - N GA Pressure Range V 0 to -30 inhg R -4.7 PSI to 7.5 PSI Pressure Range M M5 Port Output ircuit N NPN Sinking P PNP Sourcing Specificatis Pressure Range Vacuum ompound bar: 0.00 bar: 0.0 Units of Measure kpa: 0. kpa: Display Resoluti mmhg: kgf/cm : 0.0 inhg: 0. PSI: 0. Media Air and N-orrosive Gases Pressure Port M5F Proof Pressure V: 7.5 PSI, R: 6 PSI Operating Temperature 3 to F (0 to 50 ) Storage Temperature 4 to 40 F (-0 to 60 ) Humidity 35 to 85% RH Electrical necti m Grommet Open Lead Power Supply 0.8 to 30VD, Ripple Vp-p 0% Max., Reverse Voltage Protecti Display 3-Digit, 7-Segment LED Display Refresh 0. sec. Fixed Output ircuit NPN (Sinking) or PNP (Sourcing) Open ollector Transistor, 30VD, 5mA Linear Outputs Analog Output to 5VD Switch Outputs Switch Output, Normally Open, NPN or PNP, LED Indicator Output Mode Hysteresis: 0 to 00% of Switch Point omparative: limits selectable over full range Output Respse Time <.5ms Repeatability ± 0.% F.S. Thermal Error % over ±5 (77 ) Temperature hange: Range 3 to F (0 to 50 ) General Protecti IP65, E Marked, EM Rating: EN550 lass B, EN5008- urrent sumpti < 60mA Vibrati Resistance 0 to 55Hz,.5mm, XYZ, hrs. Shock Resistance 0 G, XYZ Material Body: Polycarbate; Pressure Port: Anodized Aluminum Mass 0.53 oz. (5g) 7 Parker Hannifin orporati Divisi

72 Technical Informati Pressure Sensor MPS-9 Thin Open ollector and Analog Wiring Grommet Lead Only Brown: 4VD Blue: 0VDc Black: NPN / PNP Open ollector White: Analog to 5VD Brown V+ White Analog to 5 VD Blue 0V Black NPN / PNP Output Internal ircuit (Brown) +V (Brown) +V Main ircuit 500 (Black) Out LOAD Max. 5mA (White) Analog to 5VD + D - 0.8V to 30V Main ircuit 500 (Black) Out LOAD Max. 5mA (White) Analog to 5VD + D - 0.8V to 30V (Blue) OV (Blue) OV NPN Open ollector with Analog Opti PNP Open ollector with Analog Opti autis! Installati The MPS-9 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for explosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install as shown using the metal mounting bracket. Operatis Dedicate a power supply of 0.8 to 30VD to the sensor and set the ripple to Vp-p0% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating temperatures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er System Error (Internal) tact Factory E Over current of Output Load current exceeds FFF Applied pressure exceeds Apply pressures with FF pressure range the rating of the sensor 7 Parker Hannifin orporati Divisi

73 Dimensis Pressure Sensor MPS-9 Thin Dimensis M5 Female, Grommet.3 (8).09 (53).39 (0) Pressure Port M5 (0).9 (5).59 (5).35 (9).6 (4).3 (3.) Dia. -Places 73 Parker Hannifin orporati Divisi

74 MPS-9 Programming Features Pressure Sensor MPS-9 Thin See page 87 for Symbol Explanati Press x Switch Output Press for 3 Secds Setting Hysteresis Setting Will Display for Secd Will Display for Secd Wait 5 Secds Wait 5 Secds 3 Lock 4 Press for 3 Secds Zero Reset Unlock 5 Power Supply Off Selecting Units of Measure Press When Powering Up Negative Pressure kpa bar ompound Pressure kpa bar mmhg kfg/cm inchg PSI 74 Parker Hannifin orporati Divisi

75 Notes 75 Parker Hannifin orporati Divisi

76 Features SPSD Pressure Sensor SPSD High Pressure 36 Stainless Steel Features Stainless Steel or eramic Diaphragms UL Listed and E Marked Pressure Ranges -4.7 to 50 PSI 0 to 3000 PSI 0 to 000 PSI 0 to 5000 PSI 0 to 000 PSI 0 to 9000 PSI Sensor Outputs PNP Open ollector Transistor Output, 30 VD, 00mA Optial Additial urrent, 4 to 0mA Programming of Switch Point, High / Low Values, NO / N Selectable Units of Measure PSI, bar, Mpa Output Respse Time Less than 5.0ms Mx Micro nector Error Message Password Lockable Polarity Protected Short ircuit Protected 4 Digit LED Display Swivels 90 o Output Modes The SPSD Sensor has two independent PNP open collector output signals and an optial analog output. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 00% below the Switch Point (SP). The Window omparator Mode provides two Switchpoint Settings (rsp) and (SP) that ctrol the output signals (PNP) between two pressures. This is referred to as the High / Low setting. The optial Analog Output Signal is calibrated to the pressure scale of the sensor. Switch Output 50 PSI SP h off off 0 Window omparator Output 50 PSI off SP rsp off off 76 Parker Hannifin orporati Divisi 0

77 (Revised 9/9/04) Ordering Informati, Specificatis Pressure Sensor SPSD High Pressure 36 Stainless Steel Model Number Index Bold Items Are Stocked SPSD - 050P Pressure Range 0030P -4.7 to 30 PSI 000P -4.7 to 00 PSI 050P -4.7 to 50 PSI 0500P 0 to 500 PSI 000P 0 to 000 PSI 000P 0 to 000 PSI 3000P 0 to 3000 PSI 5000P 0 to 5000 PSI 9000P 0 to 9000 PSI Output 0 PNP without 4-0mA Analog Signal PNP with 4-0mA Analog Signal Pressure Port* 7 7/6-0 UNF (SAE-4) * BSPP Pressure Ports are available. sult Factory for Model Number. Housing Metal Housing, Female Thread Electrical nector 7 4-Pin, M 5* 5-Pin, M * Output, With Analog Signal Specificatis Pressure Range ode 0030P 000P 050P 0500P 000P 000P 3000P 5000P 9000P Measuring Range (PSI) -4.7 to -4.7 to -4.7 to 0 to 0 to 0 to 0 to 0 to 0 to Overload Pressure (PSI) Burst Pressure (PSI) Sensing Element eramic Stainless Steel Stainless Steel.4404 Parts in tact with Media eramic AL 0 3, NBR* Stainless Steel.4404,.454, NBR* *FPDM, EPDM Special Request Switch ycles >00 Milli Output Respse Time < 0ms Power Supply 5 to 30VD, lass Power Supply Electrical necti M x, 4-Pin or 5-Pin Short ircuit Protecti Yes,.4 Amp / Open ollector Output Reverse Polarity Protecti Yes Overload Protecti Yes urrent sumpti < 00mA Output ircuit PNP (Sourcing) Open ollector Transistor Analog Output 0/4 0mA, Programmable, Freely Scaleable Output Functis Hysteresis, Window omparator Switching Voltage -.5vdc Maximum urrent Output A with Open ollector Outputs,.5A per Output Accuracy ± 0.5% F.S. Typ., ± % Max. Repeatability ± 0.5% F.S. Display Accuracy ± 0.5% F.S. Typ., ± Digit Thermal Error Max. ±0.03% F.S. at -4 to 85 F (-0 to 85 ) Material Pressure Die-cast Zinc Z 40: Surface-finishing Display Material Polyester Pressure Port 7/6-0 UNF-B (SAE-4) General Protecti IP 67, EN6059, UL, E Marked, EM-EN5008- lass B, EN Temperature Range of Media -4 to 85 F (-0 to 85 ) Ambiant Temperature Range -4 to 85 F (-0 to 85 ) Storage Temperature -40 to F (-40 to 00 ) Display 4-Digit, 7-Segment LED, Red, 9mm Height Tightening Torque 35Nm Vibrati Resistance 0G, 0 to 500Hz, IE Shock Resistance 50 G, XYZ, ms, IE Mass 0.6 oz. (300g) 77 Parker Hannifin orporati Divisi

78 Technical Informati Pressure Sensor SPSD High Pressure 36 Stainless Steel Internal ircuit M, 4-Pin, PNP Outputs M, 5-Pin, PNP Outputs with 4 to 0mA Analog (Sensor Socket) Brown Black White Blue +Ub (4VD) S S 0V / Gnd (Sensor Socket) Brown Black White Gray Blue +Ub (4VD) S S Analog Out 0V / Gnd 5 M, 4-Pin, PNP Output with 4 to 0mA Analog Brown +Ub (4VD) (Sensor Socket) 4 Black S Note: M, 5-Pin Female able nector will fit both M, 4-Pin and 5-Pin Male Sensor nector. White Analog Out 3 Blue 0V / Gnd 4 3 Installati Mechanical:! AUTION: Install and de-install the SPSD ly when there is no pressure present. Attach the SPSD to the appropriate process cnecti. Installati should be undertaken ly with a mm, across flats spanner. Ensure that the digital display is placed in the best viewing positi by using the rotatial housing adjustment. Turn the SPSD manually to the required positi. Maximum 90. Excessive turning beyd the easily detectable end stop will lead to damage. The housing can be attached: with self-tapping screws into two blind holes at the back of the housing with the mounting plate provided with cable ties Avoid static and dynamic over-pressures which exceed the specified overload pressure. Even when the overload pressure is exceeded ly for a short time the SPSD may be damaged. Parker Sensotrol diagnostic systems are recommended for measuring pressure peaks exactly. If there is a danger of excessively high pressure peaks, it is recommended to: use an SPSD with a higher nominal instrument pressure (analog output can then be correspdingly matched) install a standard throttling device upstream from the SPSD Electrical:! AUTION: The SPSD may be installed ly by a qualified electrician in accordance with the respective natial and internatial regulatis. Protect the SPSD from electomagnetic influences and over-voltages. Optial installati tips which are shown by experience to reduce the influence of interference: Use shorter cables Avoid short distances between cnecting leads and power csuming devices and interference generating electrical and electric equipment Use free running diodes Error Messages Display Att Err Err Err3 Descripti The set value is lower than the other respective parameters. When Enter is activated, the smaller value is matched up. System Error (Internal) Nominal instrument pressure range was exceeded by 0%. Please check system pressure. Nominal instrument pressure range has been exceeded. Error in analog electrics. Please check system pressure. 78 Parker Hannifin orporati Divisi

79 Accessories Pressure Sensor SPSD High Pressure 36 Stainless Steel ables (IP 67 Rated) B-M-4P-M, Female to Open Lead B-M-5P-M, Female to Open Lead.84 Ref. (46.7mm).50 Ref. (38.mm) 5-Pin 4-Pin.57 Dia. Ref. (4.5mm) Mx Ref. (9.7mm) Female Interface 5-Pin, M Female Interface 4-Pin, M Male Interface 5-Pin, M Male Interface 4-Pin, M able Pin olor Brown White 3 Blue 4 Black 5 Gray 3 4 able Pin olor Brown White 3 Blue 4 Black B-M-4P-M-M, Female to Male B-M-5P-M-M, Female to Male.84 (46.7mm).0 (5.3mm) Dia. (4.48mm).57 Dia. (4.48mm) 5-Pin 4-Pin Mx 5-Pin 4-Pin B-M-5P-M (38.8mm) Female Interface 5-Pin Dia. (4.48mm)..98 (3mm) (5mm) able Pin olor Brown White 3 Blue 4 Black 5 Gray Dimensis Switch Output.56 (39.5) Switch Output (Also Error Output).8 (46.3) I II Sensotrol UNIT 3.89 (98.5).89 (73.4).55 (4).98 (5) 7/6-0 UNF-B (SAE-4).06 (6.8).6 (3) 79 Parker Hannifin orporati Divisi

80 Programming Features Pressure Sensor SPSD High Pressure 36 Stainless Steel ( ) or ( ) Password Yes Menu Right Page To Program Outputs and Optis of SPSD, press and hold the (Up Arrow Ic) then press the (ircle Ic) until Pro6 is displayed. Release all butts and follow menu to program outputs and optis. Parameters Shown in Digital Display To program switch outputs in menu S (S = output ) or S (S = output ), press and hold, then press. Pro6 will be displayed for secds. PRS This is dedicated to a password. Entry into the programming mode can be secured ly when the correct figures have been entered Menu for programming the switch outputs: S S = Switch output S S = Switch output (Menu is not active if S is being used as an error output) Switching point (SP): upper limiting value / pressure, at which the switch output changes its status. SP SP = Switch output ; input as pressure value (e.g. 400 bar) SP SP = Switch output ; input as pressure value (e.g. 430 bar) rsp Reverse switching point (rsp): lower limiting value/pressure at which switch output changes its status. rsp rsp = Reverse switching point (rsp) of switch output ; input as pressure value (e.g. 390 bar) rsp = Reverse switching point (rsp) of switch output ; input as pressure value (e.g. 40 bar) The reverse switching point is always smaller than its respective switching point. If the reverse switching point is set higher than the switching point, the reverse switching point will be set automatically 0.5% of the instrument nominal pressure below the switching point. The warning sign Att (attenti) will appear, which can be cleared with Enter. To Review Programed Outputs and Optis of SPSD, press and hold the (ircle Ic) until Pro6 is displayed. Release the (ircle Ic) and follow menu to program opti and status. ct Switch output as nopn = closer nls = opener Func Selecti of switching functis: HySt = Hysteresis functi FEn = Window functi Delay times; input from 0 to 9.99 s. dspi dspi = delay time switching point output drsl drsi = delay time reverse switching point output dsp dsp = delay time switching point output drs drs =delay time reverse switching point output Optis Program (See Next Page) 80 Parker Hannifin orporati Divisi

81 Programming Features & Dimensis Settings for Optis Program op Optis program PA5 Password input 0000 = no password Example password 34 = 34 uni Setting of units: bar = bar NPA= MPa PSi= PSI dis Display: Value which will be shown the digital display in run mode. Act = Actual system pressure Nin = Minimum system pressure; (pressure troughs) NA = Maximum system pressure; (pressure peaks) SPl = Switch point SP = Switch point OFF = off indicati AnA Setting of analog output (see point 4) 0-0 = 0-0 ma 4-0 = 4-0 ma FroN alibrati of starting value (0 or 4 ma) for the analog output. Settable from 0 to nominal instrument pressure. Example for AnA = 4-0: 0000 = at 0 bar the analog output yields 4 ma. The starting value is always smaller than the end value. If the! starting value is set greater than the end value, then the starting value will be automatically set 5% of the nominal instrument pressure below that of the end value. The warning sign Att will appear, which can be cleared with the Enter sign. to alibrati of end value (0mA) for the analog output. Settable from 0 up to nominal instrument pressure. 000 = at 0 bar the analogue output yields 0 ma. Pressure Sensor SPSD High Pressure 36 Stainless Steel 0Set! res Err Zero adjustment: The actual pressure will be stored as a new zero point. For safety reass this is limited to the range ± 5% of the nominal instrument pressure. Applicati example: a system with a ctinuous residual pressure, but which should be displayed as 0 bar. OFF = factory calibrati yes = undertake zeroing adjustment now no = go back to the menu and do not make any new zeroing adjustments. After a zeroing adjustment, a pressure of up to 0 bar can be displayed as 0 a 400 bar SPSD. Before working a system, it must be ensured that there is no pressure in it. learing the minimum and maximum value memory yes = yes, clear memory now no = no, do not clear memory Programming switch output as an error output yes = yes no = no Switch Output can be used optially as an error output to display pressure switch functi errors. As an error output it is normally closed, and in case of errors (Err, Err, Err 3) it is open. At the same time LED II lights up. The display and the output remain active until the error is cleared. SUn Indicati of Software Versi dpp Setting of the decimal point. (The maximum number of decimal points depends the nominal pressure of the SPSD instrument) 0000 = no decimal point = decimal point = decimal points = 3 decimal points End End of programming mode Electrical Test Unit (M, 5-Pin) SSN-450-PSD SPSD Programming Kit SSD-PRG-KIT Optical Interface Device that allows read / write and storing of SPSD cfigurati data. Kit includes optical interface device, electrical test unit with P cable (RS3 cnector) and software. Optical Interface Device SPSD 8 Parker Hannifin orporati Divisi

82 Pressure Sensor ables Accessories Features M8, M Male / Female nector Length: m or 5m over: PV or PUR necti Type: Swivel Straight or Angled IP 67 Swivel nector omm Part Numbers Item nector tacts Length over B-M8-4P-M M8 Female 4 m PV B-M8-4P-5M M8 Female 4 5m PUR B-M8-4P-5M-90 M8 Angled Female 4 5m PUR B-M8-4P-M-M M8 Female to M Male 4 m PV B-M8-4P-M8-M M8 Female to M8 Male 4 m PV B-M8-4P-E M8 Female 4 m PV B-M-4P-M M Female 4 m PV B-M-5P-M M Female 5 m PV B-M-5P-M-90 M Female 5 m PV B-M-4P-M-M M Female to M Male 4 m PV B-M-5P-M-M M Female to M Male 5 m PV B-M8-4P-M, Female to Open Lead B-M8-4P-M-M, M8 Female to M Male (9,7) Dia.47 () Dia.96 (5) Dia.6 (3).09 (53) B-M8-4P-5M, Female to Open Lead B-M8-4P-M8-M, M8 Female to M8 Male (9,7) Dia (9,7) Dia.96 (5) Dia 6.40 ft (5m).6 (3).96 (5) Dia.6 (3) B-M8-4P-5M-90, Female to Open Lead (9,7) Dia.75.4 (9) (0,7) (9,7) Dia B-M8-4P-E, M8 Female Shield.96 (5) Dia Housing (AMP) 78-5 nector (AMP) (7).96 (5) Dia 6.40 ft (5m).87 () Female Interface 4-Pin, M8 Male Interface 4-Pin, M8 Male Interface 4-Pin, M B-M-4P-M, Female to Open Lead B-M-5P-M, Female to Open Lead.84 Ref. (46.7mm).50 Ref. (38.mm) able Pin olor Brown White 3 Blue 4 Black 5-Pin 4-Pin.57 Dia. Ref. (4.5mm) Mx Ref. (9.7mm) Female Interface 5-Pin, M Female Interface 4-Pin, M Male Interface 5-Pin, M Male Interface 4-Pin, M able Pin olor Brown White 3 Blue 4 Black 5 Gray 3 4 able Pin olor Brown White 3 Blue 4 Black.57 Dia. (4.48mm) B-M-4P-M-M, Female to Male B-M-5P-M-M, Female to Male.84 (46.7mm).0 (5.3mm).57 Dia. (4.48mm) B-M-5P-M (38.8mm)..98 (3mm) (5mm) Female Interface 5-Pin able Pin olor Brown White 3 Blue 4 Black 5-Pin 4-Pin Mx 5-Pin 4-Pin.57 Dia. (4.48mm) 5 Gray 8 Parker Hannifin orporati Divisi