2-Color Display Digital Pressure Switch

Size: px

Start display at page:

Download "2-Color Display Digital Pressure Switch"

Tracy Jones
5 years ago
Views:

-Color Display Digital Pressure Switch (F)/(H) Series Stainless diaphragm Oil-free (Single-layer diaphragm structure) Sensor unit: Stainless steel 630 Fitting parts: Stainless steel 304 The sensor

1 -Color Display Digital Pressure Switch (F)/(H) Series Stainless diaphragm Oil-free (Single-layer diaphragm structure) Sensor unit: Stainless steel 630 Fitting parts: Stainless steel 304 The sensor unit and fitting parts are also applicable to stainless steel 36L. RoHS IP65 compliant ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 PS IS3 IS ISE35 PSE IS ISG ZSM -color display See abnormal values at a glance. Choice of piping directions Rear ported Bottom ported 3-step setting 3 Push djust to the set-value by the or button. Push Completion of setting Rated range 0.0 to 0.0 kpa and 0.00 to.00 MPa available as standard 89

Leakage x 0-0 Pa m 3 /s <Face seal and compression fitting> x 0-5 Pa m 3 /s <Threaded type (R, Rc, NPT, G)> Welded structure for sensor units and fitting parts Select from a face seal or compression

2 Leakage x 0-0 Pa m 3 /s <Face seal and compression fitting> x 0-5 Pa m 3 /s <Threaded type (R, Rc, NPT, G)> Welded structure for sensor units and fitting parts Select from a face seal or compression fitting. Face seal Compression Confirmation of the atmospheric of a load lock chamber pplicable Fluid Examples Water Hydraulic fluid (JIS-K3) Silicon oil (JIS-K3) Lubricant (JIS-K630) Fluorocarbon Suction verification of work pieces containing moisture Confirmation of supply of cleaning lines rgon Carbon dioxide ir-containing drainage Nitrogen pplications Confirmation of working of hydraulic cylinder Confirmation of after lubricator unit Restrictor installed fitting type (-X50) Made to Order switch that has a restrictor installed in the fitting is available to prevent the sensor from being damaged by water hammer or inertia of the fluid. Series Variations F H 0.0 to 0.0 kpa 00.0 to 00.0 kpa 0.00 to.000 MPa 0.00 to.00 MPa MPa MPa Rated range 00 kpa 0-0kPa 0 00 kpa 0 0. MPa ( 00 kpa) 0 0. MPa ( 00 kpa) 90 Withstand Minimum unit setting Repeatability 500 kpa MPa 4 MPa 0. kpa 0.00 MPa ±0.%F.S. ±digit

-color display (LCD) Can select from 4 indicator patterns of color combinations. ON OFF 3 4 Red Green Red Green Green Red Red Green Output display It lights when or outputs.

3 -color display (LCD) Can select from 4 indicator patterns of color combinations. ON OFF 3 4 Red Green Red Green Green Red Red Green Output display It lights when or outputs. Convex rubber button Convex button is adopted and provides IP65 rating. Improved maneuverability and operability. m (Standard) 3 m (Made to Order) Secret code setting This ensures that only authorized persons can operate the switch when the key is locked. Input an arbitrary 3-digit value. The set-value can be confirmed even when the key is locked. Power-saving mode Turning off the display can save power consumption. (Power consumption: reduced by up to 8%) Lead wire length Rc/8 (female threaded) is newly added. R/4 (M5 x 0.8 female threaded) NPT/4 (M5 x 0.8 female threaded) G/4 (M5 x 0.8 female threaded) Rc/8 NPN open collector output PNP open collector output NPN open collector outputs PNP open collector outputs URJ/4 (Face seal fitting) TSJ/4 (Compression fitting) nalog current output is newly added. dvantageous when it is wired for a long distance. It is resistant against noise. NPN open collector outputs nalog voltage output/uto-shift switching PNP open collector outputs nalog voltage output/uto-shift switching NPN open collector outputs nalog current output/uto-shift switching PNP open collector outputs nalog current output/uto-shift switching Resolution switching function It prevents minor variation of the indicated value. Output Piping /000 /00 (Only the indicated value changes without changing precision.) MPa/kPa switching function The indication unit for vacuum, compound and positive can be integrated into either MPa or kpa. ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 PS IS3 IS ISE35 PSE IS ISG ZSM The numerical value disappears and the decimal points blink. Front protection cover Panel mount Suitable for side-by-side mounting Space-saving Reduced panel fitting labor 40 Bracket mount Bracket Only one opening Bracket 9

-Color Display Digital Pressure Switch For General Fluids RoHS / Series For positive For vacuum/ compound Rated range 80 0 to 0 kpa 80F 00 to 00 kpa N P B R T S V Piping specifications R/4 0 (M5

4 -Color Display Digital Pressure Switch For General Fluids RoHS / Series For positive For vacuum/ compound Rated range 80 0 to 0 kpa 80F 00 to 00 kpa N P B R T S V Piping specifications R/4 0 (M5 female threaded) NPT/4 N0 (M5 female threaded) G/4 F0 (M5 female threaded) C0 Rc/8 URJ/4 (Face seal fitting) TSJ/4 B (Compression fitting) Not applicable to piping direction L (Bottom ported). ccording to ISO 8- Made to Order How to Order ISE 80 0 N ZSE 80 0 N Nil L Rated range to MPa 80H 0. to MPa Piping direction Rear ported Bottom ported Not applicable to piping specifications F0(G/4). Output specifications NPN open collector output PNP open collector output NPN open collector outputs PNP open collector outputs NPN open collector outputs nalog voltage output/uto-shift switching PNP open collector outputs nalog voltage output/uto-shift switching NPN open collector outputs nalog current output/uto-shift switching PNP open collector outputs nalog current output/uto-shift switching Symbol Specifications Note ) -X500 Wetted parts: Stainless steel 36L -X50 Lead wire length 3 m -X50 Note ) Restrictor installed fitting -X53 Note 3) M 4-pin pre-wired connector -X555 Note 4) Rated 00 to 300 kpa Note ) Not applicable to the rated range 0. to MPa specification. Refer to page 03 for detail. Note ) Excluding and B piping specifications Note 3) Suitable for output specifications, B only Note 4) Suitable for output specifications R, T only Option Option Piping direction Part no. Rear ported ZS-4- Bracket Rear ported ZS-4-D Bottom ported ZS-35- Panel mount adapter Rear ported ZS-35-C Bottom ported ZS-35-B Panel mount adapter Front protection cover Rear ported ZS-35-F Bottom ported ZS-35-E 9 Table Made to Order Nil B C D M M None With bracket With bracket Note) Rear ported Panel mount adapter ZS-35-C Rear ported Panel mount adapter Front protection cover ZS-35-F Note) Rear ported only Made to Order Refer to Table below. Option Symbol Nil Y K T Unit specifications With unit display Note ) Nil switching function Fixed SI unit Note ) M With unit display switching function Note ) P (Initial value psi) Rear ported Operation Note) manual ZS-4- Calibration Note) certificate Note) Under the New Measurement Law, sales of switches with the unit switching function are not allowed for use in Japan. Note) Unit H : MPa Others : MPa, kpa Option ZS-4-D Bottom ported Bottom ported Bottom ported Note) ll texts in both English and Japanese ZS-35- ZS-35-B ZS-35-E

5 -Color Display Digital Pressure Switch For General Fluids / Series Specifications Refer to pages and for Pressure Switch Precautions. For details about the Specific Product Precautions, refer to the Operation Manual on the SMC website, Click here for details. Model Rated range Pressure display range/set range Withstand Wetted parts material pplicable fluid Port size Power supply voltage Current consumption Switch output Repeatability Hysteresis nalog output uto-shift input Display Display accuracy Indicator light Function Environment Temperature characteristics Lead wire Standards Maximum load current Maximum load voltage Residual voltage Response time Short circuit protection Hysteresis mode Window comparator mode Output voltage Voltage (Rated range) output Linearity Output impedance Output current (Rated range) Current Linearity output impedance Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance Note ) When F0(G/4) is selected. Note ) F0(G/4) is available for rear ported only. (Vacuum ) (Positive ) 0.0 to 0.0 kpa 00.0 to 00.0 kpa 0.00 to.000 MPa 0.00 to.00 MPa 0.0 to. kpa 0.0 to 0.0 kpa 0.05 to.00 MPa 0.05 to.0 MPa 500 kpa MPa 4 MPa Pressure sensor: Stainless steel 630, Fitting: Stainless steel 304 (Gasket: NBR Note ) ) Fluids do not corrode stainless steel 630 and 304 (NBR Note ) ) R/4, NPT/4, G/4 Note ), URJ/4, TSJ/4, Rc/8 Piping direction: Rear/Bottom to 4 VDC ±0%, Ripple (p-p) 0% or less (with power supply polarity protection) 45 m or less NPN output, NPN outputs, PNP output, PNP outputs 80 m 8 V (at NPN output) V or less (with load current of 80 m).5 ms (with anti-chattering function: 0, 00, 500, 000, 000 ms) Yes ±0.% F.S. ± digit to 5 V ±.5% F.S. 4 to 0 m ±.5% F.S. F (Compound ) Variable (0 or above) ±% F.S. pprox. kω.4 to 0 m ±.5% F.S. ±% F.S. Maximum load impedance: 300 Ω (Power supply voltage V) 600 Ω (Power supply voltage 4 V) Minimum load impedance: 50 Ω Non-voltage input (Reed or Solid state), Low level: 0.4 V or less, 5 ms or longer input 3 /-digit, 7-segment, -color LCD (Red/Green) ±% F.S. ± digit (mbient temperature of 5 ±3 C) Lights up when output is turned ON., : Orange nti-chattering, Zero-clear, Keylock function, uto-preset, uto-shift, Display unit switching, Power-saving mode IP65 Operating: 0 to 50 C, Stored: 0 to 60 C (No freezing or condensation) Operating/Stored: 35 to 85% RH (No condensation) 50 VC for minute between terminals and housing MΩ or more (50 VDC measured via megohmmeter) between terminals and housing ±3% F.S. (5 C reference, within operating temperature range) Oilproof heavy-duty vinyl cable, 3 cores (N.P) 4 cores (.B) 5 cores (R.T.S.V) CE, UL/CS (E6656), RoHS H (Positive ) 0.6 to 5 V ±.5% F.S. 0.8 to 5 V ±.5% F.S. 3. to 0 m ±.5% F.S. ø3.5, m Conductor area: 0.5 mm (WG6) Insulator O.D.: 0.95 mm ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 PS IS3 IS ISE35 PSE IS ISG ZSM Piping Specifications Model Port size Weight (Bottom ported) Weight (Rear ported) Leakage 0 R/4 7 g 89 g N0 NPT/4 F0 G/4 C0 Rc/8 URJ/4 B TSJ/4 8 g 4 g 0 g g 90 g 86 g 86 g 9 g 83 g x 0 5 Pa m 3 /s x 0 0 Pa m 3 /s 93

6 / Series Set Pressure Range and Rated Pressure Range Set the within the rated range. The set range is the range of that is possible in setting. The rated range is the range of that satisfies the specifications (accuracy, linearity, etc.) on the switch. lthough it is possible to set a value outside the rated range, the specifications will not be guaranteed even if the value stays within the set range. Switch Pressure range 00 kpa 0 00 kpa MPa MPa For vacuum 0 kpa. kpa 0 0 kpa For compound F 00 kpa 0 kpa 00 kpa 0 kpa For positive H 0. MPa MPa 0.05 MPa. MPa 0. MPa 0.05 MPa MPa. MPa Rated range of switch Set range of switch nalog Output Voltage output nalog output [V] B C Current output nalog output [m] Pressure B C Range For vacuum For compound For positive Pressure Rated range 0.0 to 0.0 kpa 0. kpa B 0 C 0.0 kpa 00.0 to 00.0 kpa 00.0 kpa 00.0 kpa 0.00 to.000 MPa 0.00 MPa MPa 0.00 to.00 MPa 0.00 MPa Note) 0.00 MPa Note) nalog output is 0.8 [V] or 3. [m] at the. 94

7 U U -Color Display Digital Pressure Switch For General Fluids / Series Internal Circuits and Wiring Examples -N NPN ( output) -P PNP ( output) Main circuit Brown DC () Black to 4 VDC Main circuit Brown DC () Black to 4 VDC ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 - NPN ( outputs) Main circuit Brown DC () Black White to 4 VDC -B PNP ( outputs) Main circuit Brown DC () Black White to 4 VDC PS IS3 IS ISE35 PSE IS -R/-S -R: NPN ( outputs) nalog voltage output -S: NPN ( outputs) nalog current output Main circuit Brown DC () Gray nalog output Black White to 4 VDC -R/-S NPN ( outputs) uto-shift input Main circuit Brown DC () Gray uto-shift input Black White to 4 VDC ISG ZSM -T/-V -T: PNP ( outputs) nalog voltage output -V: PNP ( outputs) nalog current output Main circuit Brown DC () Gray nalog output Black White to 4 VDC -T/-V PNP ( outputs) uto-shift input Main circuit Brown DC () Gray uto-shift input Black White to 4 VDC 95

8 / Series Dimensions (For details about lead wires, refer to the product specifications.) ZSE/ISE8-0 N0 F0 C0 B (N0: 50.) M5 x 0.8 thread depth : R/4 N0: NPT/4 x M3 x 0.5 thread depth 4 Width across flats 7 ø tmospheric vent port ø When the switch is used in a place where water and dust splashes may occur, insert a tube into the atmospheric vent port, and route the other end of the tube to a safe place away from water and dust. SMC TU045 (polyurethane, O.D. ø4, I.D. ø.5) suits to the switch. Note) If it is predicted that the, such as the water hammer or surge fluctuates rapidly, refer to the Handling Precautions stated in the Operation Manual at SMC website ( Rc/8 M5 x 0.8 thread depth 5 G/4 -C0: Rc/8 -F0: G/ URJ/4 TSJ/4 96 -: URJ/4 -B: TSJ/4

9 -Color Display Digital Pressure Switch For General Fluids / Series Dimensions (For details about lead wires, refer to the product specifications.) ZSE/ISE8-0L N0L C0L L BL M5 x 0.8 thread depth 5 ø Width across flats 7 tmospheric vent port ø (N0L: 6) 0L: R/4 N0L: NPT/4 When the switch is used in a place where water and dust splashes may occur, insert a tube into the atmospheric vent port, and route the other end of the tube to a safe place away from water and dust. SMC TU045 (polyurethane, O.D. ø4, I.D. ø.5) suits to the switch. Note) If it is predicted that the, such as the water hammer or surge fluctuates rapidly, refer to the Handling Precautions stated in the Operation Manual at SMC website ( 0 0 x M3 x 0.5 thread depth 4 ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 PS IS3 IS ISE PSE IS ISG ZSM Rc/8 URJ/4 TSJ/4 -C0L: Rc/8 -L: URJ/4 -BL: TSJ/4 97

10 / Series Dimensions With bracket (Rear ported) ZS ø With bracket (Rear ported) ZS-4-D 30 View x ø With bracket (Bottom ported) ø

11 -Color Display Digital Pressure Switch For General Fluids / Series Dimensions Panel mount adapter (Rear ported) Panel thickness to 5 mm ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 PS IS3 IS ISE35 PSE 38.6 Panel fitting dimensions IS ISG ZSM 36± x n pcs. 4 x (n pcs. ) 36±0.3 36±0.3 4 x R3 or less 67 or more 4 x R3 or less 99

12 / Series Dimensions Panel mount adapter (Bottom ported) ± x n pcs. 4 x (n pcs. ) 36± Panel thickness to 5 mm 38.6 Panel fitting dimensions 4 x R3 or less 4 x R3 or less 00

13 -Color Display Digital Pressure Switch For General Fluids / Series Function Details The F in ( ) shows the function code number. Refer to the Operation Manual for the details of operation procedures and function codes. Click here for details. uto-shift function (F4) When there are large fluctuations in the supply, the switch may fail to operate correctly. The auto-shift function compensates such supply fluctuations. It measures the at the time of auto-shift signal input and uses it as the reference to correct the set-value on the switch. Set-value correction by auto-shift function (Differential) Pressure Switch output () uto-shift input Supply normal P- (P-3) H- (H-) ON OFF Hi Lo Output specifications: -R/-S NPN ( outputs) uto-shift input Pressure Switch Brown DC() Gray uto-shift input Black to 4VDC White Output specifications: -T/-V PNP ( outputs) uto-shift input Pressure Switch Supply drop Rectified value B Switch output 5 ms or more 0 ms or less response time when autoshift is input. Brown DC() Gray uto-shift input Supply increase Rectified value When the auto-shift is selected, ooo will be displayed for approximately second, and the value at that point will be saved as a rectified value C_5. Based on the saved rectified values, the setvalue Note) of P_, H_, P_, and H_ will likewise be rectified. Note) When an output is reversed, n_, H_, n_, H_ will be rectified. Settable Range for uto-shift Input Set range Settable range Compound 0.0 to 0.0 kpa 0 to 0 kpa Vacuum 0.0 to.0 kpa.0 to.0 kpa Positive 0.05 to.00 MPa.05 to.05 MPa 0.05 to.0 MPa.3 to.3 MPa uto-shift zero The basic function of auto-shift zero is the same as the function for auto-shift. lso, it corrects values on the display, based on a value of 0, when the auto-shift is selected. Black White to 4VDC Rectified value B uto-preset function (F8) uto-preset function, when selected in the initial setting, calculates and stores the set-value from the measured. The optimum set-value is determined automatically by repeating vacuum and break with the target workpiece several times. Suction Verification Indicated value of High Vacuum Max. P- H- n- Min. B tmosphere ±5% R.D. Suction Work Work Released Work Work Work n Formula for Obtaining the Set-Value P_ or P_ P_ (P_) = (-B)/4 n_ (n_) = B (-B)/4 0 pplied Work n H_ or H_ H_(H_)= (-B)/ Indicated value at the time of shipment djustable range of display calibration function Note) When the display calibration function is used, the set value may change ± digit. D Peak/Bottom value indication This function constantly detects and updates the maximum (minimum) value and allows to hold the maximum (minimum) value. When the buttons are simultaneously pressed for second or longer, while holding, the hold value will be reset. E Keylock function Prevents operation errors such as accidentally changing setting values. F Zero-clear function This function clears and resets the zero value on the display of measured. For the switch with analog output, the analog output shifts according to the indication.the indicated value can be adjusted within ±0% F.S. of the when ex-factory. 0 ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 PS IS3 IS ISE35 C Display calibration function (F7) Fine adjustment of the indicated value of the sensor can be PSE made within the range of ±5% of the read value. (The scattering of the indicated value can be eliminated.) IS ISG ZSM

14 / Series Function Details The F in ( ) shows the function code number. Refer to the Operation Manual for the details of operation procedures and function codes. Click here for details. G Error indication function Error name Overcurrent error Residual error pplied error uto-shift error System error Error code H nti-chattering function (F3) large bore cylinder or ejector consumes a large volume of air in operation and may experience a temporary drop in the supply. This function prevents detection of such temporary drops in the supply as an error. <Principle> This function averages values measured during the response time set by the user and then compares the average value with the set point value to output the result on the switch. Pressure Internal data error Internal data error Internal data error Description current of 80 m or more is applied to the switch output (). current of 80 m or more is applied to the switch output (). It is still applied with that is ±0% over the atmospheric and the upper limit of the rated range when it is cleared to zero. fter displaying the error code for second, the switch automatically returns to the measuring mode. Due to individual product differences, the setting range varies ± digits. Supply exceeds the maximum set. Supply is below the minimum set. The value measured at the time of auto-shift input is outside the set range. fter displaying the error code for one second, the switch returns to the measuring mode. vailable response time settings 0 ms, 00 ms, 500 ms, 000 ms, 000 ms Momentary change I Display unit switching function (F0) Display units can be switched with this function. Pressure range For compound For vacuum Model F K Setting of secret code (F0) For positive H kpa MPa kgf/cm bar psi inhg mmhg H: Does not indicate the last digit when the is.000 MPa or higher. J Power-saving mode (F9) The numerical value disappears and the decimal points blink. Power-saving mode can be selected. It shifts to the power-saving mode without button operation for 30 seconds. It is set to the normal mode (Power-saving mode is OFF.) when ex-factory. (Decimal points and operation indicator light (only when the switch output is turned ON.) blink in the power-saving mode.) Input an arbitrary 3-digit value. The set-value can be confirmed when the key is locked. Users can select whether a secret code must be entered to release key lock. t the time of shipment from the factory, it is set such that the secret code is not required. Set-value P- H- t (ms) t (ms) Time <veraging> <veraging> Switch output operation in normal conditions ON OFF Switch output operation when ON anti-chattering function is on. OFF Time Time 0

15 / Series Made to Order Please contact SMC for detailed dimensions, specifications and lead times. Made to Order Wetted Parts: Stainless Steel 36L This switch has better corrosion resistance that uses stainless steel 36L for the wetted parts ( sensor and fitting). How to Order (F)/ Piping specifications Output specifications Option Specifications Refer to How to Order on page 9 for standard specifications. X500 Note ) Not applicable to the rated 0. to MPa specifications (H). Note ) restrictor (equivalent to -X50) is installed inside the fitting. (Piping specifications (L) and B(L) are excluded.) Model (F) Withstand 500 kpa.5 MPa pplicable fluid Liquids and gases do not corrode stainless steel 36L Models other than above are the same specifications as standard. 3 Restrictor Installed Fitting restrictor is installed inside the fitting in order to improve endurance of water collision with inertia force in the piping when adsorption is broken. How to Order (F)/ (H) Piping specifications Output specifications Refer to How to Order on page 9 for standard specifications. Option X50 Lead Wire Length 3 m It has a lead wire extended to 3 meters. How to Order (F)/ (H) 4 Piping specifications How to Order Output specifications X53 Refer to How to Order on page 9 for standard specifications. Option X50 M 4-pin Pre-wired Connector (Lead wire length 00 mm) (F)/ (H) Refer to How to Order on page 9 for standard specifications. X53 Piping specifications Option Output specifications : NPN open collector outputs B: PNP open collector outputs ZSE0 ISE0 ZSE30 ISE30 ZSE40 ISE40 ZSE0 ISE0 ISE70 PS IS3 IS ISE35 PSE IS ISG ZSM 00 Connector pin numbers White Brown 3 Blue Black Made to Order -X50 Restrictor Standard Without restrictor Note ) Not applicable for piping specifications (L) and B(L). Note ) Sometimes does not work for suppression of water hammer effect even if this product is used. Take other measures in such a case. M 4-pin connector ø5 4.5 Pin no. 3 4 Pin name DC() () DC( ) () 03

16 / Series Made to Order Please contact SMC for detailed dimensions, specifications and lead times. Made to Order 5 Rated Pressure -00 to 300 kpa Symbol -X555 It has an extended range of F (compound ) to -00 to 300 kpa. How to Order Refer to How to Order on page 9 for standard specifications. F Piping specifications X555 Option Output specifications Note) R: NPN open collector outputs nalog voltage output/uto-shift switching T: PNP open collector outputs nalog voltage output/uto-shift switching Note) The output is applicable to R, T only. Specifications Model F X555 Rated range 00 to 300 kpa Set range Set display resolution nalog output voltage Display accuracy 0 to 330 kpa kpa to 5 V ±3% F.S. Linearity:.5% F.S. ± 3% F.S. ± digit (mbient temperature of 5 ±3 C) Models other than above are the same specifications as standard. Unit switching function Pressure unit Set display resolution Rated range Set range kpa 00 to to 330 P MPa to to GF kgf/cm to to 3.37 br bar to to 3.30 PSi psi to to 47.9 inh inhg to to 97.4 mmh mmhg 750 to to 999 The setting or display over the range of ±999 is not available when mmhg is selected. Settable Range for uto-shift Input 440 to to to to to to to

10 switches simultaneously. The settings of the master sensor (source of copy) can be copied to the slave sensors. Reducing setting labor

10 switches simultaneously. The settings of the master sensor (source of copy) can be copied to the slave sensors. Reducing setting labor 2-Color Display High-Precision Digital Pressure Switch ZSE ISE RoHS ZSE ISE IP65 ZSE40 ISE40 M8 connector type ZSE10 ISE10 ISE70 ZSE80 ISE80 PS ISA3 ISA2 ISE35 Applicable Air, Non-corrosive gas, Non-flammable