PASSPORT Mortise Lock. Installation Instructions A8032G 04/16

Transcription

1 P1 PASSPORT 1000 Mortise Lock Installation Instructions A8032G 04/16 Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

2

3 Table of Contents Warning...3 General Description...4 Hardware Specifications...4 Electronic Specifications...4 Installation Wiring...5 Parts Breakdown...9 Installation Instructions...10 Operational Check ! Warning FCC Industry Canada: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l interférence canadienne causant des règlements d équipement. L opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l interférence nocive, et (2) ce dispositif doit accepter n importe quelle interférence reçue, y compris l interférence qui peut causer l opération peu désirée. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d un type et d un gain maximal (ou inférieur) approuvé pour l émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l intention des autres utilisateurs, il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l intensité nécessaire à l établissement d une communication satisfaisante. Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings. To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components: Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches and mounting plates especially when mounting electronic components such as readers and controllers onto the door Leave components (reader and controller) protected in their respective anti-static bags until ready for installation. Do not touch pins, leads or solder connections on the circuit boards WIRE A8032G

4 2 General Description An ANSI/BHMA Grade 1 lock utilizing Power over Ethernet (PoE) technology, the Passport 1000 P1 provides a cost-effective, future-proof solution for campuses. Featuring multiclass SE Technology from HID Global, it provides simultaneous support for multiple credentials and offers an easy migration path to higher security credentials and mobile access. Recognized for its contribution to sustainable buildings, the P1 re-uses existing IEEE 802.3af PoE infrastructure, streamlines the installation process, reduces costs and components, and minimizes power consumption. 3 4 Hardware Specifications Complete locksets with controller ADA Compliant Easily retrofits existing Passport 1000 door preps (mortise locks) Latch 1/2" standard 3/4" throw fire-rated double doors (optional) (41- prefix) Deadlocking latch Inside lever retracts latch Electronic Specifications ANSI/BHMA A Listed Grade 1 Compliant Outside lever is unlocked through access control credentials only Outside lever controlled by any combination of keypad, magnetic swipe, contactless reader or mechanical cylinder May be used for indoor and outdoor applications NOTE: A weather-protective gasket is required for outdoor applications. HID multiclass SE technology offers support for the following credentials: 2.4 GHz credential compatibility: Secure Identity Object (SIO) on Mobile IDs (Bluetooth Smart) MHz credential compatibility: iclass iclass SE (SIO-enabled) iclass Seos SIO on MIFARE Classic SIO on MIFARE DESfire EV1 MIFARE Classic DESfire EV1 NFC-enabled mobile phones 125 khz credential compatibilty: HID Prox Magnetic Stripe 2,400 users per lock; 10,000 event audit trail Multiple time zone and holiday access scheduling First-In unlock configuration, based on specified time schedule Uses existing Magstripe keycards (track 2) Magnetic Stripe Card Coercivity: HiCo (4000 Oersted) or LoCo (300 Oersted) Power Requirements: 55VDC, 90mA PoE Class 1 Device, as defined by IEEE 802.3af, requires less than 3.84 watts over structured cabling UL Listed* - UL 294 Indoor Use CUL Listed - S319: Class 1 UL 294 Access Control Ratings: Destructive Attack Level 1 Line Security Level 1 Endurance Level 4 Standby Power Level 1 *UL testing was conducted on product powered by UL Listed model 9001GR/AC injector; manufactured by Microsemi Corp WIRE A8032G

5 5 Installation Wiring Overview SARGENT Passport Series PoE P1 Typical Application Supplied by Others Network Cable Network Switch (802.3af) Surface Mount RJ45 LMT: Lock Management Tool A. PoE frame harness assembly B. PoE data hinge from McKinney (patent pending) C. PoE door harness* from McKinney D. Passport Series v.p1 PoE Lock A B C D * Door width determines length WIRE A8032G 5

6 Installation Wiring (Continued) Supplied by CI B-Splice Crimp Connector Certified Integrator (CI) supplies and terminates the B-Splice connector and the male RJ45 connector from harness to end user provided facility cable Patch Cable Patch Panel to PoE Switch To building or electrical ground Supplied by End User PoE Switch PoE Switch is Terminated to Earth Ground Ceiling RJ45-M RJ45-F Jack Cable: CAT 5e or higher 24 AWG Patch Panel Frame-Side Harness Assembly (15' length) Cable: CAT 5e or higher 24 AWG 100ohm Molex-M A Molex-F Molex-F Molex-M B Cable: CAT 5e, 26 AWG stranded, 100ohm C Ground Ring Terminal Secured to Lock Mounting Plate Wiring to TIA/568-B Standard RJ45-M D PoE Lock Notes: Approved Software Connectors go on only one way. They cannot be placed in an incorrect position. Do not force and do not offset connectors Be sure they are completely seated (flush) PoE power source cannot be connected to a receptacle controlled by a switch WIRE A8032G

7 Installation Wiring (Continued) A Frame Harness Installation Supplied by CI B-Splice Crimp Connector Components and wire harness supplied by McKinney. Suggested installation: Cut end / ceiling-side PoE harness: TIA/EIA 568-B Standard Wiring PIN Wire Pair Number 1 pin 8 8 pin 1 1 White/Orange 2 Ceiling RJ45-M 2 Orange 2 3 White/Green 3 4 Blue 1 5 White/Blue 1 B 24AWG Stranded Drain Wire for Earth Ground in 15' Frame Harness Frame-Side Harness Assembly (15' length) Cable drain wire concealed in shrink tubing Cable: CAT 5e or higher 24 AWG 100ohm Molex-M PoE Data Hinge Frame 4-pin M 6-pin M 4-pin F 6-pin F Do not confuse pair numbers with pin numbers. A pair number is used for reference only (eg: 10BaseT Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack. Hinge side of PoE harness: 1. Feed cut end of harness into hole on hinge-side through single access hole. 2. Push one connector back through the hole and feed into the other access hole. Each of the hinge-side harness connectors should end up threaded through a different access hole and matched to the same size pin connector from the door harness: 4-pin male molex connector 6-pin male molex connector with ground wire PoE Hinge 4-pin F 6-pin F Hinge-side harness connectors: 4-pin female molex connector 6 Green 3 7 White/Brown 4 8 Brown 4 6-pin female molex connector with ground wire Lock-side harness connectors: 4-pin female molex connector 6-pin female molex connector with ground wire WIRE A8032G 7

8 C PoE Door Harness Order of installation may vary. Refer to appropriate sections for instructions. Hinge-side harness connectors: 4-pin male Molex connector 6-pin male Molex connector with ground wire Lock-side harness connectors: Ring terminal Male RJ45 connector (crimped after cable is fed through door) Notes: Connectors go on only one way. They cannot be plugged to incorrect position. Do not force and do not offset connectors. Be sure they are completely seated (flush). PoE Lock 4-pin F 4-pin F 4-pin M RJ45-M 6-pin F 6-pin F 6-pin M Cable: CAT 5e, 26 AWG stranded, 100ohm D PoE Lock Order of installation may vary. Refer to appropriate sections for instructions. 1. Prop door open. 2. Using the ring terminal, carefully route the assembly through the door channel to the lock. Inside of Door PoE Harness (Cat 5e) WIRE A8032G

9 6 Parts Breakdown P1 PoE Lock with Magnetic Card Swipe With or Without Keypad ITEM No. PART No. DESCRIPTION [finish] Outside Escutcheon Assembly, mag stripe [finish] Outside Escutcheon Assembly, mag stripe and Keypad (shown) [finish] Outside Escutcheon Assembly, Mag Swipe, Keypad, and HID 125 khz Prox [finish] Outside Escutcheon Assembly, iclass, keypad, mag stripe, Prox, smart card (MIFARE, DESFIRE) [finish] Outside Escutcheon Assembly, iclass, mag stripe, Prox, smart card (MIFARE, DESFIRE) [finish] Outside Escutcheon Assembly, FeliCa, keypad, mag stripe, Prox [finish] Outside Escutcheon Assembly, FeliCa, mag stripe, Prox [finish]* Outside Escutcheon Assembly, Standard Reader and Keypad [finish]* Outside Escutcheon Assembly, Standard Reader [finish]* Outside Escutcheon Assembly, Felica Reader and Keypad [finish]* Outside Escutcheon Assembly, Felica Reader Mounting Plate Assembly PoE Controller Assembly [finish] Inside Escutcheon Assembly with Privacy Button Door Position Switch Kit *Bluetooth Smart option WIRE A8032G 9

10 Parts Breakdown (Continued) 5 4 3* Tools Required: #2 Phillips screwdriver Flat head T20 Torx driver Security allen wrench ITEM PART No. DESCRIPTION 1 See catalog #41 Cylinder (1-1/8" Minimum Length) 2 Consult Factory Cylinder Rosette 3 P [finish]* Lock body with deadbolt & with cylinder P [finish]* P [finish]* P [finish]* Lock body with deadbolt without cylinder Lock body without deadbolt with cylinder Lock body without deadbolt without cylinder KB Thumb turn for Deadbolt Functions Only 5 See catalog Inside Lever Handle 6 See catalog Outside Lever Assembly Trim Pack Standard Levers (shown) Trim Pack Deco Levers & 7900 all lever styles 8 See catalog Mortise Rose Spindle Spring 10 Consult factory Mortise screw pack - specify finish (includes: wood and metal lock body screws, faceplate screws, and strike screws) Outside Front Plate (Electrical, Latchbolt & Guardbolt) Outside Front Plate (Electrical, Deadbolt, Latchbolt and Guardbolt) *Bluetooth Smart option WIRE A8032G

11 7 Installation Instructions 1 Door Preparation A. Verify Hand and Bevel of Door Left Hand Hinges Left. Open Inward. LH Left Hand Reverse Bevel Hinges Left. Open Outward LHRB Right Hand Hinges Right. Open Inward. RH Right Hand Reverse Bevel Hinges Right. Open Outward. RHRB B. Verify Product Label C. Door Preparation Field prep template: A8064 for wood and metal doors Door manufacturers template: 4651 Through Bolt Holes Raceway for PoE Controller Cutout Cylinder Hole Lever Handle Holes Outside of Door Mortise Pocket Inside of Door Through Bolt Holes Inside Mounting Plate Mounting Holes Raceway for PoE Controller Cutout Thumb Turn Location (Deadbolt Functions Only) Lever Handle Holes WIRE A8032G 11

12 2 Prepare Lock Body 1. Reverse Lock Hand Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A): a. Position lock body with red surface of locking piece visible. b. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body. c. Rotate the locking piece 180 until RED surface is on opposite side. Note: Red indicates locked side (outside). Locking Guide Slot: Red color indicates locked side. Fig. 2A Push In Right Hand Lock Shown 2. Reverse Latch Hand Beveled surface of latch must face strike (Fig. 2B). The deadlatch is self adjusting. To change hand of latchbolt: a. Insert screwdriver into spade (triangular)- shaped slot. b. Rotate screwdriver 90º to push latch out until back of latch clears lock front; then rotate latch 180º. Latch will then re-enter lock body. Note: Latch cannot be unscrewed. Triangular Slot Fig. 2B Latchbolt WIRE A8032G

13 3 Install Lock Body Note: Do not pull the lock into the pocket using the harness alone. Ensure that the wire harness is not pinched between the lock and the mortise pocket. 1. Feed the wire harness into the mortise pocket and through inside preparation hole as depicted in Figure Carefully push the lock body into the pocket while lightly applying tension to the wire harness. 3. Insert (2) #12-24 screws into the lock body (Fig.4) and partially tighten* with a screw driver. *Do not fully tighten until cylinder and levers are installed and properly aligned. Inside of Door Ground Wire Cat 5e cable from hinge (2) #12-24 screws Wire Harness Fig WIRE A8032G 13

14 4 Outside Cylinder Installation 1. Slide the spring and the rosette onto the cylinder. 2. Rotate the cylinder into cylinder hole with fingers. 3. Insert key 75% of the way and utilize the key to rotate the cylinder into the rest of the cylinder hole. Note: Do not attempt to tighten all the way. 4. Verify that orientation of cylinder has the SARGENT logo as depicted in Fig. 4A. 5. Hand tighten the cylinder clamp screw with Phillips screwdriver to prevent unscrewing of the cylinder (Fig 4C). 6. Test cylinder function: Key retracts latchbolt and deadbolt (7976 function) Key retracts latchbolt (7978 function) Cylinder not present for 7977 and 7979 functions IMPORTANT: Position cylinder so that the SARGENT logo is positioned correctly. Correct Fig. 4A Incorrect Outside of Door Cylinder Rosette Spring Fig. 4B Fig. 4C Phillips Screwdriver Cylinder Clamp Screw WIRE A8032G

15 5 Assemble Outside Trim 1. With outside lever horizontal, insert the mounting posts through outside of door and lock body. Make certain the lever spindle is properly engaged inside the lock body (Fig 5A). 2. On the inside of the door, insert spindle into square hole of mortise lock (Fig 5B). 3. Slide inside adapter and plate assembly over spindle and secure with (2) 8-32 X 5/8" Phillips oval head and lock washer machine screws. Note: Ensure that position of set screw hole on inside adapter is oriented to match location of hole in inside lever handle. Outside of Door Inside of Door Outside Trim Ground Wire Fig. 5A Detail Outside Trim Spindle Fig. 5A Spindle Fig. 5B Wire Harness (From Lock Body) Set Screw Hole WIRE A8032G 15

16 6 Install Inside Rose and Inside Lever Assembly 1. Place inside rose flush against door surface and rotate first counter-clockwise to seat the threads, then clockwise to securely tighten. 2. Slide lever onto spindle until fully seated. Be sure handle is horizontal and facing the hinge side of the door. Push lever onto spindle so minimum gap is visible. 3. Tighten the set screw securely with a T20 Torx driver. 4. Finish securely tightening (2) #12-24 lock body screws. 5. Before closing the door, test that the lever is functional and ensure smooth operation of the latchbolt. Inside of Door #12-24 screws Spindle Rose Fig. 6 Set Screw Inside Lever 7 Install Thumb Turn 1. Insert thumb turn into preparation hole and engage slot in lock body. 2. Orient mounting plate so screw hole is vertical (aligned with preparation holes). 3. Secure plate with Phillips screw provided (Fig. 7). 4. Test thumb turn for function by retracting and projecting the deadbolt (7976 and 7977 functions only). Thumb Turn Assembly Fig. 7 Inside of Door Phillips screw WIRE A8032G

17 8 Install Gasket (Optional) and Outside Escutcheon Note: Gasket is optional, for non-fire rated doors only. For non-fire rated door applications, a gasket (Part number ) may be used as a weather seal between the escutcheon and the outside door surface. Outside of Door 1. Peel off adhesive backing and attach to outside escutcheon. 2. Insert the mounting posts through holes as shown. 3. Feed reader cable through side opening (Fig. 8). Escutcheon Gasket 9 Mounting Plate Assembly Fig On the inside of the door, position the mounting plate over the indicated holes. 2. Feed reader cable and ground ring terminal through central opening on mounting plate (Fig. 9). 3. Route PoE Harness through alternate opening (to the right of the central opening). 4. Route ground ring terminal from lock body through bottom of mounting plate and attach to bottom right corner using (1) #8-32 x 1-7/8 flat head machine screw. 5. Insert other three #8-32 x 1-7/8 flat head machine screws and tighten, fastening the outside escutcheon to the door (Fig. 9). IMPORTANT: If the following step is skipped, the product will not be UL-compliant: 6. Attach two (2) #8 x 3/8 flat head wood screws for wood doors or (2) #8-32 x 3/8 flat head machine screws for metal doors (Fig. 9). Fig. 9 Ground Lugs PoE Harness WIRE A8032G 17

18 10 Installation of Connectors CAUTION - Do not touch or allow debris to enter connector contacts. Secure the following connectors to their respective terminals (Fig. 10A): A. Secure the 10-pin lock body assembly connector. IMPORTANT: Do not run wires through bottom hole in plate (Fig. 10A) - it will damage wires and controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 10A). Secure Mounting Plate 1. Tuck excess cable into wire hole on inside of door. 2. Secure the mounting assembly while ensuring proper alignment of outside reader and fully tighten the (2) throughbolts on the inside of the door to secure the reader and plate to the door. B B. Secure the 24-pin card reader connector (Fig. 10A). Reader (24-pin) A C. Crimp* RJ45 to Cat 5e cable from hinge (Fig. 10B). *For more detail, refer to section (5) Installation Wiring, A - Frame Harness Installation. Ground Lugs Board-to-Board Connector Fig. 10A Lock Body (10-pin) TIA/EIA 568-B Standard Wiring 1 pin 8 8 pin 1 PIN Wire Pair Number 1 White/Orange 2 2 Orange 2 3 White/Green 3 4 Blue 1 5 White/Blue 1 6 Green 3 7 White/Brown 4 8 Brown 4 Do not confuse pair numbers with pin numbers. A pair number is used for reference only (e.g.: 10BaseT Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack. Cat 5e cable from hinge Fig. 10B RJ45-M Crimp* to RJ45-M Connector C WIRE A8032G

19 11 Install Inside Module Component Assembly 1. Insert top tabs of controller into slots on mounting plate (Fig. 11A). 2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate. CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller. Fig. 11B Fig. 11A 3. Connect RJ45 male Connector to female RJ45 on controller board (Fig. 11B, C). 4. Remove pull tab from its position beneath the coin cell by pulling on tab in direction of arrows printed on tab (Fig. 11B, C). Fig. 11C Coin Cell Pull Tab WIRE A8032G 19

20 12 Install Inside Escutcheon 1. Position inside escutcheon as shown (Fig. 12). Verify that all wires are positioned within the escutcheon to avoid pinching. 2. Attach escutcheon with (2) #8-32 x 1/2 T-20 Torx pan head screws. 3. Straighten escutcheon and tighten securely. DO NOT OVERTIGHTEN. Inside of Door (2) #8-32 x 1/2 Torx Screws 13 Attach Outside Front Plate Attach front plate with (2) #8-32 X 1/4 flat head screws (Fig. 13). (2) #8-32 x 1/4 Flat Head Screws Fig. 12 Inside of Door Fig WIRE A8032G

21 8 Operational Check IMPORTANT: Be sure to test functions prior to closing door. In all cases, perform the following checks: 1. Ensure that inside lever retracts latch. For units with cylinders, the following checks apply: Insert key into cylinder and rotate: a. There should be no friction against lock case or any other obstructions. If friction or binding occurs, re-adjust cylinder to eliminate issues. b. The key should retract the latch and the key should rotate freely. c. The key should extend and retract the deadbolt. For units without a keypad, add card using LCT software* and test. For units with a keypad, add pin and card using LCT software* and test. 2. LED signaling: After using a valid credential, a green flash followed by three fast amber flashes indicates a low power condition. Check the input voltage. If the input voltage is low, disconnect the lock from the power source and check the power source voltage. If the power source voltage is correct, inspect the lock wiring for a possible short. If the lock loses power, it will flash rapid blue for approximately one minute. Lock will default to programmed fail safe or fail secure. After that, the lock will no longer be functional. 3. When you have completed the tests, close the door, ensuring latchbolt fully extends into strike plate without binding. *Refer to Network and Lock Configuration Tool user manual (WFMN1) for information on how to configure and program locks WIRE A8032G 21

22 Notes WIRE A8032G

23

24 SARGENT Manufacturing 100 Sargent Drive New Haven, CT USA WIRE (9473) HID and iclass are registered trademarks of HID Global Corporation. Founded in the early 1800s, SARGENT is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company s customer base includes commercial construction, institutional, and industrial markets. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. A8032G -04/16