Contents. List of spare parts in increasing order 24. Alphabetic list of spare parts 26

Transcription

1 Contents Troubleshooting The Indigo doesn't move or suck up any litter Wall Climbing Robot Tilts Backward Robot emerging above the water line Bad Adhesion to Pool Bottom No Movement - Suction ok Filtration Ineffective 7 Assembly / Disassembly Tools Required Brushes Your robot is fitted with foam pads Your robot is fitted with rubber brushes Rotor Handle Bumper Motor Unit Protective Screen Track Plate on Traction Side (side opposite cable) Removal of the Track Plate Track Drive Roller - Transmission Belt - Track Track Plate Belt Tension Jacks Belt Settings Fitting the Traction Track Plate (side opposite cable) Cable Side Track Plate Removing the Cable-Side Track Plate Track Guide Roller Track Track Plate Plate Assembly (cable side) on the Housing Motor Unit Removing the Motor Unit Replacing the Motor Unit 14 Technical Diagrams General Diagram Motor unit - W1287A and W1655A Control unit - W1664A 18 Control unit - W1207A Motor housing cover - W0684B and W0684C Housing - W1286A Flexible lead kit - W1313A Trolley - W1534A Geared traction motor - W1166A Packing box bag of accessories - W1116A Filter holder - W1201A Pump motor - W1290A 23 List of spare parts in increasing order 24 Alphabetic list of spare parts 26 3

2 Dear Sirs, Thank you for the confidence you have shown in BARACUDA technology for automatic pool cleaning. It is thanks to pool professionals that we have become the European and world leader in the field of hydraulic appliances. This is why we wish to be in even closer contact with you, the better to respond to your needs and offer you a constantly improving technical and sales service. The Indigobook is the technical guide distributed only to pool industry professionals selling INDIGO TM robots by ZODIAC. It supplements the information given to the user in the technical instructions provided with the appliance. This information will enable you to give valuable advice to your INDIGO TM owning customers. It will also help you adjust the robot effectively to suit the configuration of every pool for optimum performance. The design of ZODIAC appliances has always been oriented to simplicity and reliability. Please do not hesitate to contact our technical service or to get in touch with our usual sales contact for further information. The ZODIAC POOL CARE EUROPE technical and sales team The ZODIAC product INDIGO TM is made by ZODIAC POOL CARE EUROPE S.A.S.U. 4

3 1 Troubleshooting 1.1. The Indigo doesn't move or suck up any litter You've switched on and tried to start Indigo but it doesn't do anything. POSSIBLE CAUSES The red indicator light doesn't come on when you start a cycle (Turbo or Perfect) The red light comes on but the robot won't start CHECKS AND CORRECTIVE ACTION Plug in another electrical appliance to check the plug Check the robot cable is properly connected to the control unit 1.2. Wall Climbing Indigo goes forwards and backwards without any problems but has difficulty climbing the walls or can't climb them at all. POSSIBLE CAUSES The filter bag is clogged with litter, scale or flocculents There are microscopic algae on the sides of the pool The belts have become slack The belts and tracks are slipping (fatty bodies present) CHECKS AND CORRECTIVE ACTION Empty and clean the filter bag with clear water. Use soap if necessary Check the quality of the water and apply any necessary treatment; lower the ph slightly (remove the unit from the water prior to shock chlorination) If necessary, clean the sides with a hand broom Tighten or replace the belts (never add grease or silicone) Clean the tracks, belts and pulleys by means of an adequate product 1.3. Robot Tilts Backward The robot tilts backwards at the foot of the sidewall. POSSIBLE CAUSES The rotor is broken or obstructed by foreign bodies The robot's suction system is malfunctioning CHECKS AND CORRECTIVE ACTION Remove any hairs, pieces of cloth or foreign bodies obstructing the rotor or replace the rotor if it is broken Bring the robot up to just below the water level and check for backflow at the turbine screen outlet. If the pump isn't working, ask your supplier for the necessary after-sales service 5

4 1.4. Robot emerging above the water line The robot is emerging above the waterline and is sucking in air. The robot is too light because there's air in it POSSIBLE CAUSES The water level is too high, which forces the robot to come into contact with the edging The lining is furred or the ph of the water is low CHECKS AND CORRECTIVE ACTION Turn the robot over to expel the air from the filter bag and press the foam pads Lower the water level Adjust the ph and clean the waterline 1.5. Bad Adhesion to Pool Bottom The robot doesn't stay properly on the bottom of the pool, and even wants to pull away from the bottom. The robot is too light because there's air in it POSSIBLE CAUSES The rotor is broken or obstructed by foreign bodies The robot's suction system is malfunctioning CHECKS AND CORRECTIVE ACTION Turn the robot over to expel the air from the filter bag and press the foam pads Add more ballast Remove any hairs, pieces of cloth or foreign bodies obstructing the rotor or replace the rotor if it is broken Bring the robot up to just below the water level and check for backflow at the turbine screen outlet. If the pump isn't working, remove the motor unit and ask your supplier for the necessary after-sales service No Movement - Suction ok The Indigo won't go forwards or backwards, but the suction system is working properly (backflow at turbine outlet). The belts are slack POSSIBLE CAUSES The beta pin has come out of its housing and fallen into the motor unit protective screen or into the robot The belts and tracks are slipping (fatty bodies present) The traction motor is malfunctioning CHECKS AND CORRECTIVE ACTION Tighten the belts or replace them Change and refit the pin Clean the tracks, belts and pulleys by means of an adequate product Ask your supplier for the necessary after-sales service. 6

5 1.7. Filtration Ineffective The filtration system is not working properly or the rotor is throwing up litter. POSSIBLE CAUSES The filter bag is clogged with litter, scale or flocculents The rotor is broken or obstructed by foreign bodies The filter bag has come unstitched and may even be torn The filter bag has not been properly fitted: the base is incorrectly positioned A foreign body (small stone, branch, leaf, etc.) is stuck in the suction holes in the filter holder The black flap valves are deformed or missing CHECKS AND CORRECTIVE ACTION Empty the filter bag and clean it with clear water and, if necessary, soap Remove any hairs, pieces of cloth or foreign bodies obstructing the rotor or replace the rotor if it is broken Change the filter bag Reposition the filter bag elastic or replace the bag if the elastic has become too slack Clear the filter bag inlet Replace the black flap valves 7

6 2 Assembly / Disassembly 2.1. Tools Required > No-bounce mallet > Cordless drill/screwdriver > Flat-nose pliers > Wrench Ø 19 (packing gland) > Automatic stripping pliers > Ogival head oblique cutting pliers > Lever-operated grease pump > Set of screwdrivers for slotted-head screws > Set of screwdrivers for cross-recessed screws 2.2. Brushes Your robot is equipped with foam pads We recommend that you change the pads at the end of each season. It is essential to change them if their surface becomes smooth or worn. > Turn the robot upside down. > Separate the pads to reveal the pad clips, lift them up (with a lever of necessary, then take them out. Be careful not to separate them too widely. Photo 1. Photo 1 Photo 2 > Remove the worn pads and fit new ones, smooth side inside. > Replace the clips. Photo 2. > Tighten the pads around the clips. 8

7 Your robot is equipped with SEBS rubber pads The pads include wear indicators. To get the best performance out of the cleaner, replace the pads as soon as one of the wear indicators is reached (even if the pad wear is uneven). Photo 3. To do this, proceed as follows: > Turn the robot upside down. > Remove the tabs from the slots in the first pad. > Remove the worn pad. > To position the new pad, thread the part without blades around the pad-holder. Photo 4. > Thread each tab into its slot and pull them gently through to the other side of the slot. Photo 5. > Cut the tabs with scissors to even them up with the other blades. Photo 6. > Follow the same steps for the second pad. Photo 3 Photo 4 Photo 5 Photo Rotor a) Disconnect the rotor from the control unit. b) Holding the flow guide remove the four 2.9 X 9.5 (W0351A) self-tapping screws. c) Remove the rotor (using a screwdriver as a lever). d) Remove the flow guide to clear access to the rotor. e) Refit the rotor. f) Refit the flow guide and the four screws (make sure the rotor isn't touching the flow guide). 9

8 Handle The handle can be removed from the housing to avoid scratches if you need to take out the track plates. To remove the handle, unscrew the two M5X35 and the spreaders. Photo 7. a c 2.5. Bumper The bumper needs to be removed before removing the plates. a) Position a large flat-bladed screwdriver between the bumper and the housing, using the brush holder as a lever. b) Repeat this step in the opposite corner. c) Remove the 2 halves assembled (1 front, 1 lateral) Motor Unit Protective Screen a c a) Free the filter holder. b) Remove the two 3.5 X 13 self-tapping screws. c) Remove the moor unit protective screen and then the ballast weights (The robot comes with a single ballast weight on the cable side) Track Plate on Traction Side (side opposite cable) When you remove the traction-side plate you can change the following parts: > The track, > The track guide roller, > The brush holders, > The track plate, > The drive roller, > The belts, > The S and C shaped belt tension jack Removal of the Track Plate Before removing the plates you have to remove the bumpers, the handle and motor unit protective screen. You can then start to remove the plate. a) Remove the self-tapping screw at the top of the plates. b) Turn the robot upside down. Then use flat-nose pliers to remove the Beta pin from the traction motor axle. c) Remove the track opposite the plate. a b c 10

9 d) Remove the three 3.9 X 25 self-tapping screws and the washers. e) Carefully free the plate and the brush holders. d e You can now access all the traction components: Track Take out the old track and fit the new one Drive Roller - Transmission Belt - Track You have to take out all the moving parts of the plate in order to change any one of them. Assembly: a) Undo the belt tension jacks and turn them to face the bottom of the plate. b) Put the track on the plate. c) Place the drive roller on the plate and place a belt in each groove. The location of the belt is given by the S or C belt tension jack. d) Place the brush holder in the plate housing. Place the belt in the appropriate groove in the brush holder such that it is opposite the brass roller of a tension jack. e) Place the other brush holder in its housing. Make sure you place the belt in the right groove without disturbing the first brush holder. b c d With the robot fully assembled, adjust the belt tension jack (see 2.7.6) Track Plate Remove all the parts of the plate. a) Put the belt tension jack on the plate shaft. The screw must be tight on the plate side. b) Place the track roller in the plate shaft. c) To fit the moving parts, follow the procedure described in the previous paragraph Belt Tension Jacks Remove the belt tension jack and fit a new one in its place. Adjust the fit in the centreline of the belt and also the tension Belt Settings To check belt tensions are correct, pres them in A or B: the deformation [E] should be equal to ± 5 mm and should offer resistance to traction. If not, readjust the tension: 11

10 a) Undo the 2 locking screws. b) Press on the tension jack to readjust belt tension. c) Hold the tension jack down and retighten the screws.! Important! The two tension jacks are set separately and should be set strictly one after the other Fitting the Traction Track Plate (side opposite cable) All the parts should be placed on the track plate before assembly on the robot. The unit should be turned upside down. a) Start by placing the top of the plate (facing the handle). b) Push the plate against the housing and insert the drive roller on to the motor shaft. c) Hold the track plate against the housing and insert the brush holder pindle into the opposite plate; then insert the other brush holder. d) Turn one of the brush holders to align the hole in the drive roller with the hole in the motor shaft (use a small screwdriver to align the holes). e) Place the Beta pin. f) Insert the 3.9 X 25 screws with their washers. g) Place the track on the brush holders. h) Turn the unit over and insert the screw on the top of the plate. a b c e f Fit the handle (lowest float on the cable side), the motor unit protective screen and the bumpers to complete the assembly of the cleaner. 12

11 2.8. Cable Side Track Plate When you remove the plate, you can change the following parts: > The track, > The track guide rollers, > The track plate Removing the Cable-Side Track Plate Before removing the track plate, remove the bumper and the motor protective screen. You can now start to start removing the track plate. a) Remove the self-tapping screw in the top of the track plate. b) Remove the track. c) Remove the three 3.9 X 25 self-tapping screws and their washers. d) Carefully free the track plate, making sure the brush holders are on the traction-side track plate. a b c You can now access numerous parts that you may need replacing: Track Guide Roller Track Replace the old part with a new one and place the complete plate on the housing.! Make sure you fit the roller in the right direction Track Plate Remove all the parts of the old plate. The carefully take out the brass spindle with pliers, making sure you don't make any scratches. With a small hammer, fit the new brass spindle to the new plate. Fit all the moving parts to the plate. Assemble the complete plate on the housing Plate Assembly (cable side) on the Housing All the parts can be assembled on the track plate. You will need to turn the unit over. a) Start by placing the top of the plate (handle side). Then fit the track plate on to the housing. b) Fit the 3.9 X 25 self-tapping screw and its washer. c) Place the brush holder spindle into the track plate, and then the other one. d) Insert the other two 3.9 X 25 screws and their washers. e) Fit the track on to the brush holders. f) Turn the unit over and insert the screw belonging to the top of the plate. a c e 13

12 Fit the handle (lowest float on the cable side), the motor unit protective screen and the bumpers to complete the assembly of the robot Motor Unit To remove the motor unit you will need to take out the bumpers, the handle, the motor unit protective screen, the plate opposite the cable and then the plate on the cable side. a! Remarque! Do not open the motor unit during the guarantee period Removing the Motor Unit a) Remove the cable clamp (press and pull). b) Turn the robot upside down and remove the four 5 x 12 screws. c) Carefully take out the motor unit with its cable. d) Cut the cable as close as possible to the stuffing box. b c d Replacing the Motor Unit The motor units are supplied with a set of parts including a stuffing box, a seal, terminals and two screws. a) Cut the floating sheath to 90 mm and strip the cable back to 45 mm. b) Pass the cable through the housing and fit the stuffing box on to the cable. c) Strip each wire to reveal 5 mm. d) Crimp the 4 terminals with a pair of crimping pliers. b c d 14

13 e f g e) Make a spot tin solder on each crimped terminal. f) Place the O-ring on the cover. g) Connect the wires to the cover (the colours are shown on the cover). h) Connect the robot and do a performance test. i) Fill the cover connection with grease (ref. W0265A). j) Position the stuffing box on the cover. The cable should be able to move freely in the stuffing box. k) Insert the two 4.2 x 13 screws. l) Use a 19 mm spanner to tighten the stuffing box until the seal is flush with the top of the cover. m) Refit the rotor on to the pump motor shaft. n) Insert the motor unit into its housing. Take the excess cable to the outside of the housing. o) Secure the motor unit to its housing with the four 5 x 12 screws. Make sure the rotor is properly centred in the flow guide and not rubbing. p) Refit the cable clamp to the housing. i j k l To complete the assembly, first fit the cable-side track plate (see 2.8.4) then the plate on side opposite the cable (see 2.7.7). Fit the handle (lowest float on the cable side), the motor unit protective screen and the bumpers. 15

14 3 Technical Diagrams 3.1. General Diagram N Description Ref: Qty 1 HANDLE CAP DIA 6MM W0002A 1 2 MOTOR SHAFT PULLEY W0010A 1 3 PIN W0011A 1 4 TRACK GUIDE PULLEY LONG W0013A 4 5 TRANSMISSION BELT W0014A 2 6 M4 WASHER A2 W0017A 6 7 BRUSH ROLLER W0018A 2 8 BELT TENSIONER FORM S W0037A 1 9 BELT TENSIONER FORM C W0038A 1 10 MOTOR PROTECTION GRID W0044A 1 11 SCREW VT TCL POZI 3,5X13 W0090A 2 12 FILTER BLOCKING SYSTEM W0095A 2 13 TRACK GUIDE PULLEY SHORT W0121A 1 14 FIXING CLIP F.FOAM BRUSH W0139A SCREW VT TCL POZI 3,9X25 W0164A 6 16 SCREW VT TFC POZI 2,9X9,5 W0351A 4 17 SCREW VT TCL POZI 3.5X19 W0375A 2 18 WHITE PROPELLER DIA 64SWR W0435A 1 19 FOAM BRUSH BLACK PPI60 W0727A 2 20 WASHER M5 A2 W1096A 2 N Description Ref: Qty 21 ACCES. BAG MOTOR HOUSING LOCKI W1116A 1 22 AXLE PULLEY TRACK W1125A 1 23 FILTER BAG AF2 W1186A 1 24 COMPLETE FILTER SUPPORT W1201A 1 25 FRONT BUMPER GREEN W1208A 2 26 SIDE BUMPER GREEN W1209A 2 27 FLANGE STICKER W1214A 2 28 CABLE STRAIN RELIEF CLIP W1215A 1 29 HANDLE SPACER W1216A 2 30 INDIGO HANDLE ASSEMBLY W1219A 1 31 FLOW OUTLET W1220A 2 32 TRACK FLANGE W1221A 2 33 BLUE TRACK W1222A 2 34 FLOATING CABLE 18M ASSEMBLY W1226A 1 35 INDIGO HOUSING ASSEMBLY W1286A 1 36 SCREW VM TCL POZI 5X30 W1412A 2 37 STAINLESS STEEL WEIGHT W1521A 2 38 MOTOR BLOC 2008 W1655A 1 39 BLUE BRUSHES W1536A 2 16

15 3.2. Motor unit W1287B (V27-A) 2004 W1655A (V28-C) 2008 N Description Ref: Qty 1 JOINT 225X3 MOTOR HOUS.CO W0071A 1 2 ANTI-MOISTURE BAG W0072A 2 3 NUT P SIDE PLATE RUNN/ROT W0126A 1 4 JOINT 19X2 SIDE PLATE MOT W0127A 1 5 JOINT 18,4X2,7 SIDE PLMOT W0128A 3 6 NUT K SIDE PLATE PUMP MOT W0129B 1 7 BRASS NUT M4 W0325A 4 8 BRASS RING M4 W0326A 8 9 RING M3 A2 W0331A NUT INDESS M3 A2 W0541A SCREW VM TCL POZI 3X20 A2 W0542A SET MOTORBLOC COVER W0684B 1 13 ACCES. BAG MOTOR HOUSING LOCKI W1116A MOTOR HOUSING ABS W1124A 1 15 DRIVEN MOTOR ASSEMBLY W1166A 1 16 INBOARD CARD W1193A 1 17 PUMP MOTOR W1290A 1 18 RED WIRE L=235 0,75 MT2003 W1302A 1 19 BLUE WIRE L=235 0,75 MT2003 W1303A 1 20 PLASTIC WEIGHT W1524B 1 21 PLOT ADHESIVE W1592A 4 N Description Ref: Qty 1 JOINT 225X3 MOTOR HOUS.CO W0071A 1 2 ANTI-MOISTURE BAG W0072A 2 3 NUT P SIDE PLATE RUNN/ROT W0126A 1 4 JOINT 19X2 SIDE PLATE MOT W0127A 1 5 JOINT 18,4X2,7 SIDE PLMOT W0128A 3 6 NUT K SIDE PLATE PUMP MOT W0129B 1 7 BRASS NUT M4 W0325A 4 8 BRASS RING M4 W0326A 8 9 RING M3 A2 W0331A NUT INDESS M3 A2 W0541A SCREW VM TCL POZI 3X20 A2 W0542A MOTOR HOUSING ABS W1124A 1 13 DRIVEN MOTOR ASSEMBLY W1166A 1 14 RED WIRE L=235 0,75 MT2003 W1302A 1 15 BLUE WIRE L=235 0,75 MT2003 W1303A 1 16 PLASTIC WEIGHT W1524B 1 17 INBOARD CARD W1557B 1 18 PLOT ADHESIVE W1592A 4 19 PUMP MOTOR SINTECH W1651A 1 20 SET MOTORBLOC COVER W0684C 1 21 ACCES. BAG MOTOR HOUSING LOCKI W1116A 1 17

16 3.3. Control unit W1664A (V4-B) N Description Ref: Qty 1 SCREW VT TFC 2,9X9,5 A2 W0115A 4 2 RING M3 A2 W0331A 2 3 NUT INDESS M3 A2 W0541A 2 4 ADHESIVE DO NOT ALLOW W0694A 1 5 SCREW VP TCL POZI 4X12 A2 W1025A 2 6 SCREW VP TCL POZI 2.2X6.5 A2 W1027A 2 7 BASE FOOT W1140A 4 8 SCREW VP TCL POZI 4x16 A2 W1158A 4 9 HOUSING E. BOX 2010 W1235B 1 10 COVER BOX 2010 W1236C 1 11 HANDLE E. BOX 2004 W1237A 1 12 SCREW VT TCL POZI 3.5X10 A2 W1238A 4 13 SCREW VM TCL POZI 3X16 A2 W1241A 2 14 E.BOX SOCKET CAP W1263A 1 15 D7 FASTENER W1289A 1 16 CORD ASSEMBLY W1313A 1 17 E-BOX GASKET W1476A 1 18 POWER SUPPLY CARD W1556A 1 19 KEYBOARD CARD W1558C 1 20 KEYBOARD W1559B 1 21 WIRE SET KEYB/POWER W1614B 1 22 WIRE SET KEYB/SOCKET W1615B 1 18

17 Control unit - W1207A (V1.1) 3.4. Motor housing cover W0684B (V1.0) W0684C (V77-A) N Description Ref: Qty 1 JOINT 5,7 X 1,9 SCREW MHCOV W0105A 1 2 SCREW VMTRL POELIER 5 X 16 W0106A 1 N Description Ref: Qty 1 MOTOR COVER W0070C 1 2 JOINT 5,7X1,9 SCREW MHCOV W0106A 1 3 SCREW VMTRL POELIER 5X16 W0105A 1 4 HACKLE 5 X 9,5 W1233A 1 19

18 3.5. Housing - W1286A (V1.0) 3.6. Flexible lead kit - W1313A (V2.0) N Description Ref: Qty 1 MAINS LEAD H05RNF 2G1 W1239A 1 2 PACKING BOX 2004 W1240A 1 3 CRIMPED LUG 1/4 W1307A 2 4 PACKING BOX GLAND NUT W1260A 1 5 INSULATOR W1308A 2 20

19 3.7. Trolley - W1534A (V1.0) N Description Ref: Qty 1 SHAKE-PROOF NUT M6 A2 W0329A 4 2 SHAKE-PROOF NUT M8 ACZ W0330A 2 3 WASHER M 8 ACZ W0334A 4 4 SCREW: VP TCL POZI 5 X 16 A2 W1026A 2 5 TROLLEY TUBE SPACER SW2 W1144A 2 6 FLAT CLAMP W1256A 2 7 WEDGE, CRT BLUE W1267A 2 8 TROLLEY WHEEL 2004 W1271B 2 9 SCREW: VM THPF 8 X 90 A2 W1275A 2 10 NUT CAP M8, BLACK W1288A 4 11 BRASS SPACER 35.5 W1291A 2 12 SCREW: VP TORX 6 X 25 W1526A 2 13 CONTROL BOX SUPPORT 2007, GREEN W1527A 1 14 CABLE HOLDER, GREEN US W1528A 2 15 SCREW: VM TORX 6 X 45 A2 W1529A 4 16 TORQUE SPANNER W1530A 1 17 CABLE SUPPORT SIDE PLATE, GREEN W1531A 1 18 CONTROL BOX SUPPORT ADHESIVE 2007 W1532A 1 19 HANDLE ENDPIECE 2007 W1621A 2 21

20 3.8. Geared traction motor - W1166A (V2.0) N Description Ref: Qty 1 SIDE PLATE DRIVING MOTOR W1155A 1 2 SEALING RING 0.8 MM W0080A 1 3 WASHER PLAST. W1099A 1 4 SCREW VM TFC POZI 4 X 10 A2 W0138A Packing box bag of accessories - W1116A (V1.0) N Description Ref: Qty 1 SCREW: VT TCL POZI 4.2 X 13 A2 W0025A 2 2 CABLE-EYE CUTOUT W0116A 4 3 SEAL 29.3 X 3.6 CHAP PE W0122A 1 4 MOTOR UNIT - ASSEMBLY PE NM W0343B 1 5 SCREW: VP POZI 5 X 12 A2 W0360A 4 22

21 3.10. Filter holder - W1201A (V1.0) * NOT INCLUDED IN THE W1201A ASSEMBLY Pump motor - W1290A (V2.0) N Description Ref: Qty 1 SIDE PLATE J PUMP MOTOR W0112B 1 2 SEALING RING 0.8 MM W0080A 2 3 SCREW VM TFC POZI 5 X 10 A2 W0137A 2 23

22 4 List of spare parts in increasing order Ref: Description W0002A HANDLE CAP DIA 6MM W0010A MOTOR SHAFT PULLEY W0011A PIN W0013A TRACK GUIDE PULLEY LONG W0014A TRANSMISSION BELT W0017A M4 WASHER A2 W0018A BRUSH ROLLER W0019B SHELL ROUND VALVE NM W0025A SCREW VT TCL POZI 4,2X13 W0029B FILTER SUPPORT BAR NM W0031A SCREW VT TCL POZI 2,9X13 W0037A BELT TENSIONER FORM S W0038A BELT TENSIONER FORM C W0044A MOTOR PROTECTION GRID W0046A LEAD WEIGHT W0071A W0072A W0080A JOINT 225X3 MOTOR HOUS.CO ANTI-MOISTURE BAG SEALING RING 0.8 MM W0081A SCREW VT TCL POZI 2,9X16 W0089A PLASTICRINGPROT. JOINT 16x6,5x1,5 W0090A SCREW VT TCL POZI 3,5X13 W0095A FILTER BLOCKING SYSTEM W0096A FILTER PLATE HOOK W0105A SCREW VMTRL POELIER 5X16 W0106A W0112B W0115A W0116A W0121A W0122A W0126A W0127A W0128A W0129B W0137A W0138A W0139A W0144B JOINT 5,7X1,9 SCREW MHCOV SIDE PLATE J PUMP MOTOR SCREW VT TFC 2,9X9,5 A2 CABLE TERMINAL TRACK GUIDE PULLEY SHORT JOINT 29,3X3,6 MOT.HOUS.L NUT P SIDE PLATE RUNN/ROT JOINT 19X2 SIDE PLATE MOT JOINT 18,4X2,7 SIDE PLMOT NUT K SIDE PLATE PUMP MOT SCREW VM TFC POZI 5X10 A2 SCREW VM TFC POZI 4X10 A2 FIXING CLIP F.FOAM BRUSH BLACK PLASTIC SCREW TROLL W0164A SCREW VT TCL POZI 3,9X25 W0169B FILTER SUPPORT VALVE 1E N W0202A WEDGE FOR UPPER PART S W0204A DGE FOR UPPER PART B W0264A SILICONE F.WATERTIGHTNESS W0265A GREASE FOR WATERTIGHTNESS Ref: Description W0325A BRASS NUT M4 W0326A BRASS RING M4 W0329A NUT INDESS M 6 A2 W0330A NUT INDESS M8 A2 W0331A RING M3 A2 W0334A RING M8 ACZ W0343B MOTOR HOUSING LOCKING SYS W0351A SCREW VT TFC POZI 2,9X9,5 W0360A SCREW VP 50 X 12 W0375A SCREW VT TCL POZI 3.5X19 W0435A WHITE PROPELLER DIA 64SWR W0541A NUT INDESS M3 A2 W0542A SCREW VM TCL POZI 3X20 A2 W0677B FILTER SUPPORT FIX.HOOKGR W0684B SET MOTORBLOC COVER W0684C SET MOTORBLOC COVER SWY W0694A ADHESIVE DO NOT ALLOW W0727A FOAM BRUSH BLACK PPI60 W0779A RUBBER BRUSH BLACK W0889A 6 FIXING CLIPS W1025A SCREW VP TCL POZI 4X12 A2 W1026A SCREW VP TCL POZI 5X16 A2 W1027A SCREW VP TCL POZI 2.2X6.5 A2 W1096A WASHER M5 A2 W1099A WASHER PLAST. W1116A ACCES. BAG MOTOR HOUSING LOCKI W1124A 2 MOTOR HOUSING ABS W1125A AXLE PULLEY TRACK W1127A WEIGHT PUMP MOTOR W1140A BASE FOOT W1144A PART TUBE TROLLEY W1155A SIDE PLATE DRIVING MOTOR W1158A SCREW VP TCL POZI 4x16 A2 W1166A DRIVEN MOTOR ASSEMBLY W1173A FOAM INSERT 96X96X50 /360 W1174A FOAM INSERT 96X96X25 /720 W1182A MOTOR BLOCK JIG W1186A FILTER BAG AF2 W1193A INBOARD CARD W1194A CONNECTOR 4 PT MALE W1195A POWER SUPPLY CARD W1197A LEAK TEST FILLING TOOL W1201A COMPLETE FILTER SUPPORT W1203A INDIGO BODY STICKER 24

23 Réf. Description W1204A INDIGO PACK W1205A TECHNICAL MANUAL W1205B TECHNICAL MANUAL 08 W1207A ELECTRONIC BOX W1208A FRONT BUMPER GREEN W1209A SIDE BUMPER GREEN W1210A TROLLEY W1212A E.BOX FOAM SEAL W1213A E.BOX STICKER TOP W1214A FLANGE STICKER W1215A CABLE STRAIN RELIEF CLIP W1216A HANDLE SPACER W1218A HANDLE FASTENING PLATE W1219A INDIGO HANDLE ASSEMBLY W1220A FLOW OUTLET W1221A TRACK FLANGE W1222A BLUE TRACK W1226A W1234A FLOATING CABLE 18M ASSEMBLY MOTOR HOUSING LEAD WEIGHT W1235A HOUSING E. BOX 2004 W1235B HOUSING E. BOX 2010 W1236A COVER EBOX 2004 W1236B COVER BOX 2007 W1236C COVER BOX 2010 W1237A HANDLE E. BOX 2004 W1238A SCREW VT TCL POZI 3.5X10 A2 W1239A MAINS LEAD H05RNF 2G1 W1241A SCREW VM TCL POZI 3X16 A2 W1256A SADDLE FOOT W1261A E.BOX CONNECTION SET W1262A E.BOX SOCKET W1263A E.BOX SOCKET CAP W1264A KEYBOARD CARD W1265A E.BOX PACK W1266A SUPPORT E. BOX W1267A CADDY WEDGING PARTS W1271A CADDY WHEEL 2004 W1271B CADDY WHEEL 2008 W1272A CADDY HANDLE W1273A D6.4 FASTENER W1274A SCREW VM THPF 6X80 A2 W1275A SCREW VM THPF DIN 931 M8X90 W1277A WEDGE FOR BRUSHES W1286A INDIGO HOUSING ASSEMBLY Réf. Description W1287B MOTOR BLOC W1288A NUT CAP W1289A D7 FASTENER W1290A PUMP MOTOR W1291A CADDY WHEEL SPACER W1292A DRIVE MOTOR WRENCH W1301A PLASTIC WASHER D4.2 W1302A RED WIRE L=235 0,75 MT2003 W1303A BLUE WIRE L=235 0,75 MT2003 W1307A CRIMPED LUG 1/4 W1308A INSULATOR W1313A CORD ASSEMBLY W1355A M6 NUT CAP W1358A CADDY BOLT FEMALE W1359A CADDY BOLT MALE W1367A MICROPROCESSOR W1412A SCREW VM TCL POZI 5X30 W1415A TIGHTNESS TESTER MOTOR BLOC W1446A COAL DRIVEN MOTOR 2003 W1447A SCREW VM TFC POZI 5X10 W1476A E-BOX GASKET W1521A STAINLESS STEEL WEIGHT W1524B PLASTIC WEIGHT W1526A SCREW TORX 6X25 A2 W1527A E-BOX HOOK W1528A CABLE HOOK W1529A SCREW TORX 6X45 A2 W1530A TORX WRENCH W1531A CABLE HOOK FLANGE W1532A E-BOX FLANGE LABEL W1534A CADDY W1536A BLUE BRUSHES W1556A POWER SUPPLY CARD W1557B INBOARD CARD W1558C KEYBOARD CARD W1559B KEYBOARD W1589A FORK WRENCH W1592A PLOT ADHESIVE W1614B WIRE SET KEYB/POWER W1615B WIRE SET KEYB/SOCKET W1621A TROLLEY HANDLE FOAM W1651A PUMP MOTOR SINTECH W1655A MOTOR BLOC 2008 W1664A E-BOX

24 5 Alphabetic list of spare parts Ref: Description W1124A 2 MOTOR HOUSING ABS W0889A 6 FIXING CLIPS W1116A W0694A W0072A W1125A W1140A W0038A W0037A W0144B W1536A W1222A W1303A W0325A W0326A W0018A W1528A W1531A W1215A W0116A W1534A W1358A W1359A W1272A W1267A ACCES. BAG MOTOR HOUSING LOCKI ADHESIVE DO NOT ALLOW ANTI-MOISTURE BAG AXLE PULLEY TRACK BASE FOOT BELT TENSIONER FORM C BELT TENSIONER FORM S BLACK PLASTIC SCREW TROLL BLUE BRUSHES BLUE TRACK BLUE WIRE L=235 0,75 MT2003 BRASS NUT M4 BRASS RING M4 BRUSH ROLLER CABLE HOOK CABLE HOOK FLANGE CABLE STRAIN RELIEF CLIP CABLE TERMINAL CADDY CADDY BOLT FEMALE CADDY BOLT MALE CADDY HANDLE CADDY WEDGING PARTS W1271A CADDY WHEEL 2004 W1271B CADDY WHEEL 2008 W1291A CADDY WHEEL SPACER W1446A COAL DRIVEN MOTOR 2003 W1201A COMPLETE FILTER SUPPORT W1194A CONNECTOR 4 PT MALE W1313A CORD ASSEMBLY W1236B COVER BOX 2007 W1236C COVER BOX 2010 W1236A COVER EBOX 2004 W1307A CRIMPED LUG 1/4 W1273A D6.4 FASTENER W1289A D7 FASTENER W0204A DGE FOR UPPER PART B W1292A DRIVE MOTOR WRENCH W1166A DRIVEN MOTOR ASSEMBLY W1261A E.BOX CONNECTION SET W1212A E.BOX FOAM SEAL W1265A E.BOX PACK Ref: Description W1262A E.BOX SOCKET W1263A E.BOX SOCKET CAP W1213A E.BOX STICKER TOP W1527A E-BOX HOOK W1664A E-BOX 2008 W1532A E-BOX FLANGE LABEL W1476A E-BOX GASKET W1207A ELECTRONIC BOX W1186A FILTER BAG AF2 W0095A FILTER BLOCKING SYSTEM W0096A FILTER PLATE HOOK W0029B FILTER SUPPORT BAR NM W0677B FILTER SUPPORT FIX.HOOKGR W0169B FILTER SUPPORT VALVE 1E N W0139A FIXING CLIP F.FOAM BRUSH W1214A FLANGE STICKER W1226A FLOATING CABLE 18M ASSEMBLY W1220A FLOW OUTLET W0727A FOAM BRUSH BLACK PPI60 W1174A FOAM INSERT 96X96X25 /720 W1173A FOAM INSERT 96X96X50 /360 W1589A FORK WRENCH W1208A FRONT BUMPER GREEN W0265A GREASE FOR WATERTIGHTNESS W0002A HANDLE CAP DIA 6MM W1237A HANDLE E. BOX 2004 W1218A HANDLE FASTENING PLATE W1216A HANDLE SPACER W1235A HOUSING E. BOX 2004 W1235B HOUSING E. BOX 2010 W1193A INBOARD CARD W1557B INBOARD CARD W1203A INDIGO BODY STICKER W1219A INDIGO HANDLE ASSEMBLY W1286A INDIGO HOUSING ASSEMBLY W1204A INDIGO PACK W1308A INSULATOR W0128A JOINT 18,4X2,7 SIDE PLMOT W0127A JOINT 19X2 SIDE PLATE MOT W0071A JOINT 225X3 MOTOR HOUS.CO W0122A JOINT 29,3X3,6 MOT.HOUS.L W0106A JOINT 5,7X1,9 SCREW MHCOV W1559B KEYBOARD W1264A KEYBOARD CARD 26

25 Ref: Description W1558C KEYBOARD CARD W0046A LEAD WEIGHT W1197A LEAK TEST FILLING TOOL W0017A M4 WASHER A2 W1355A M6 NUT CAP W1239A MAINS LEAD H05RNF 2G1 W1367A MICROPROCESSOR W1287B MOTOR BLOC W1655A MOTOR BLOC 2008 W1182A MOTOR BLOCK JIG W1234A MOTOR HOUSING LEAD WEIGHT W0343B MOTOR HOUSING LOCKING SYS W0044A MOTOR PROTECTION GRID W0010A MOTOR SHAFT PULLEY W1288A NUT CAP W0329A NUT INDESS M 6 A2 W0541A NUT INDESS M3 A2 W0330A NUT INDESS M8 A2 W0129B NUT K SIDE PLATE PUMP MOT W0126A NUT P SIDE PLATE RUNN/ROT W1144A PART TUBE TROLLEY W0011A PIN W0089A PLASTICRINGPROT. JOINT 16x6,5x1,5 W1301A PLASTIC WASHER D4.2 W1524B PLASTIC WEIGHT W1592A PLOT ADHESIVE W1195A POWER SUPPLY CARD W1556A POWER SUPPLY CARD W1290A PUMP MOTOR W1651A PUMP MOTOR SINTECH W1302A RED WIRE L=235 0,75 MT2003 W0331A RING M3 A2 W0334A RING M8 ACZ W0779A RUBBER BRUSH BLACK W1256A SADDLE FOOT W1526A SCREW TORX 6X25 A2 W1529A SCREW TORX 6X45 A2 W1241A SCREW VM TCL POZI 3X16 A2 W0542A SCREW VM TCL POZI 3X20 A2 W1412A SCREW VM TCL POZI 5X30 W0138A SCREW VM TFC POZI 4X10 A2 W1447A SCREW VM TFC POZI 5X10 W0137A SCREW VM TFC POZI 5X10 A2 W1274A SCREW VM THPF 6X80 A2 Ref: Description W1275A W0105A SCREW VM THPF DIN 931 M8X90 SCREW VMTRL POELIER 5X16 W0360A SCREW VP 50 X 12 W1027A W1025A W1158A W1026A SCREW VP TCL POZI 2.2X6.5 A2 SCREW VP TCL POZI 4X12 A2 SCREW VP TCL POZI 4x16 A2 SCREW VP TCL POZI 5X16 A2 W0031A SCREW VT TCL POZI 2,9X13 W0081A SCREW VT TCL POZI 2,9X16 W0090A SCREW VT TCL POZI 3,5X13 W0164A SCREW VT TCL POZI 3,9X25 W1238A SCREW VT TCL POZI 3.5X10 A2 W0375A SCREW VT TCL POZI 3.5X19 W0025A SCREW VT TCL POZI 4,2X13 W0115A W0351A W0080A W0684B W0684C W0019B W1209A W1155A W0112B W0264A W1521A W1266A W1205A W1205B W1415A W1530A W1221A W0013A W0121A W0014A W1210A W1621A W1096A W1099A W1277A W0202A W1127A W0435A W1614B W1615B SCREW VT TFC 2,9X9,5 A2 SCREW VT TFC POZI 2,9X9,5 SEALING RING 0.8 MM SET MOTORBLOC COVER SET MOTORBLOC COVER SWY SHELL ROUND VALVE NM SIDE BUMPER GREEN SIDE PLATE DRIVING MOTOR SIDE PLATE J PUMP MOTOR SILICONE F.WATERTIGHTNESS STAINLESS STEEL WEIGHT SUPPORT E. BOX TECHNICAL MANUAL TECHNICAL MANUAL TIGHTNESS TESTER MOTOR BLOC TORX WRENCH TRACK FLANGE TRACK GUIDE PULLEY LONG TRACK GUIDE PULLEY SHORT TRANSMISSION BELT TROLLEY TROLLEY HANDLE FOAM WASHER M5 A2 WASHER PLAST. WEDGE FOR BRUSHES WEDGE FOR UPPER PART S WEIGHT PUMP MOTOR WHITE PROPELLER DIA 64SWR WIRE SET KEYB/POWER WIRE SET KEYB/SOCKET 27