Differential Pressure Control Valve

Transcription

1 Datasheet No. : TYL-01 TYL-Series Differential Pressure Control Valve Differential pressure control valve(dpcv) can keep the differential pressure at two sides of load constant,that can improve the stability and accuracy,reduce the noise,and easy to balance and commission. Characteristics Valve body material: Brass Caliber:25~50 Differential pressure setting range:5-30kpa or 25-70Kpa Temperature range:-10~120 The max. working DP: P V 250kPa 1.Pressure hole of low pressure cavity is built-in, reduce an external connecting pipe, which avoids damage during installation. 2.Target differential pressure value can be setted by hand wheel,it is more convenient. Every number on the hand wheel is corresponding to one setted value. Pre-setting function can be realized easily on site. 3.This valve has manual closing function, plug allen wrench into the center of hand wheel, rotate it to open and close the valve. 4.Balancing diaphragm and spring are built-in, it is nice and reliable. 5.External high pressure testing point, there is locking function, one allen wrench can lock external connecting pipe. 1

2 Specification P L is 5-30Kpa P L is 25-70Kpa (mm) Caliber (in.) Type PN Max.permissible temperature ( ) Setting range (Kpa) 25 1" TYL25-2VTC /4" TYL32-2VTC /2" TYL40-2VTC " TYL50-2VTC (mm) Caliber (in.) Type PN Max.permissible temperature ( ) Setting range (Kpa) 25 1" TYL25-2VTC /4" TYL32-2VTC /2" TYL40-2VTC " TYL50-2VTC Operating Instruction Note: = Caliber PN = Pressure class. If PN25 is needed,change C to D in valve type. e.g.tyl25-2vtd-30 Materials: Valve body:brass Hpb59-1, Valve Stem:Stainless Steel, Valve Core:Stainless Steel, Diaphragm:EPDM 1.Connect capillary pipe1, As shown in the installation diagram,one end of capillary pipe connects DPCV,the other end connects with static balancing valve through 3-port testing point2.now the system is in a state of low pressure. 2.Open the plug of air hole3,then open the 3-port measuring points 2. Pour water into pipeline until it exhausts all the air in valve cavity,and lock the air hole plug 3. 3.As shown in the installation diagram,use digital differential pressure meter(see page 5) to measure differential pressure of P 2 and P 3,that is P L. 4.Setting P L, by rotating the hand wheel5. Accurately adjust the data according to data of digital pressure meter. Cut off function: on the top of hand wheel5,close the valve by allen wrench. Testing point4 Remove the cover and then insert the probe into selfsealing testing point. Capillary pipe1 2m capillary pipe is optional if longer one is needed. Attention!Must use matched capillary pipe. 2

3 Installation Note:The DPCV usually be placed in the return pipe and setted with correct water flow direction. Inlet USER Pc Outlet Debugging Instruction 1. Open the 3-port testing point 2. Open the plug of air hole and lock the air hole plug after it exhausts all the air in valve cavity Rotate hand wheel to set the DP 4. Close off function: rotate clockwise to tighten the valve 5 2 Working Range A. Kv min B. Kv nom C. Kv max D. Working Range P L ±25% 3

4 Valve Inherent Flow Selection Caliber Kvs Select the desired P L in the tables. 2.Select the same size of the valve as the pipe. 3.Check that the desired flow is smaller than the specified q max.if not,select the most similar large dimension,or a larger P L. The tables work in the following situation: H 2* P L, the valve will work effectively from 2* P L to 250kpa+ P L. 5~30kPa q min / q nom / q max (m 3 /h) p L (kpa) q min q nom q max q min q nom q max q min q nom q max q min q nom q max ~70kPa q min / q nom / q max (m 3 /h) p L (kpa) q min q nom q max q min q nom q max q min q nom q max q min q nom q max q min q nom q max p L (kpa) 70 Dimension q min q nom q max D L H Weight(kg) / /

5 Accessory Capillary pipe The standard length is 100mm,200mm is optional if longer pipe is needed. L[mm] 100 PIPE PIPE-200 Testing point 41 High voltage end is in red,low voltage end is in blue. Specifications Red CY-001-R G1/4 Blue CY-001-B 3-port testing point with cut-off function Two testing port and cut-off function CY-002 Plug For air hole G D[mm] G1/16 12 TYL-001 G1/8 14 TYF-001 G 1/4 Joint Φ20 use for connecting the pipe and testing point If there is no Static Balancing Valve in front of the DPCV, the testing point could be screwed with the threads end of Joint. Then dig a hole at the pressure-sampling position on pipe and weld the joint onto the pipe. TYF-002 Seal-capping Specifications Red Blue CY-003-R CY-003-B Hand wheel Supplied with the valve Specifications 15~50 65~ ~500 SL-001 SL-002 SL-003 Allen wrench Use for closing the valve Specifications 3mm 5mm 8mm TPS TPS TPS

6 Debugging Instrument Technical Parameters Interface Introuduction TPS is a debugging instrument for measuring and documenting of differential pressure, flow, temperature and power consumption in hydronic systems. It connects to the specialized APP sofeware in an Android phone via bluetooth which could debug faster and more economical. Max. Permissible Pressure DP Measurement Range Pressure Range during Flow measurement (Recommended Value) Medium Temperature Measurement Deviation Battery Capacity Operating Time Charge Time Ambient Temperature Ambient Humidity Charger 1000kPa TPS-200KPA.BOX: 0~200kPa TPS-1000KPA.BOX: 0~1000kPa TPS-200KPA.BOX: 3~200kPa TPS-1000KPA.BOX: 3~1000kPa -20~120 C DP Sensor: 0.25% Flow: DP Deviation+ Valve Deviation Temperature: 1 C 3000mA >20 h 6 h During Operating and Charging:0~40 C During Storage: -20~60 C(Do not leave water in the sensor when there is a risk of freezing) Max. 90%RH Output Voltage: 12.6V DC Output Current: 500mA Hydraulic Balancing Debugging Instrument TPS-200KPA.BOX TPS-1000KPA.BOX TPS KPA.BOX The TPS.app can be installed in Android phone.during the debugging, it could easily figure out the flow value and it is more intuitive than the table lookup and easer to operate! 1Status Bar: The battery status is on the left. Time is in the middle. On the right, it shows the connecting status of device, Bluetooth connection status and device battery status. When the connection works, t h is icon will flicker. 2Title Bar: the software title is in the middle, right is setting button. Its functions include equipment search, help, update and so on. Search: search for Bluetooth devices, paired and so on. Help: provide operating instructions. Update: interconnection state, update software if there is a new version. About: check the version number of the program. 3Display Bar: show current status of DP, Flow and temperature, connection status, current cycles, current KV value and Distortion Ratio. 4Formula Bar: Input basic testing parameters, including valve number, caliber choice, cycles setting, design flow, remark info. and so on. 5Operation Bar: Include calibrate, connect, data storage, view records and generate reports. Calibrate: calibrate the zero drift of the instrument. Connect: connect to the default paired device. Data Storage: store the current measuring value. View records: View the current records in the database. Generate reports: generate xls spreadsheet and store in the SD card. 6Menu Bar: include measure, data, settings and about. Measure: turn to measuring interface Data: view xls spreadsheet management. Settings: set the normal operation information, such as project name, company selection and so on. 6