44766 Centre Court (586) Clinton Twp. MI (586) Fax
|
|
- Emerald Porter
- 6 years ago
- Views:
Transcription
1
2 44766 Centre Court (586) Clinton Twp. MI (586) Fax
3 Tool Open End Muti-Grip Klamptite T Monobolt Plastic Split Nail Structural Bulbtite Floor-Tight Closed End GBP703E 3/32"-3/16" 1/8"-3/16" 1/8"-3/16" 3/16" 1/4" - X 1/8"-3/16" GBP713C X - GBP724A /4" X - GBP743C 1/4"-5/16" 1/4" 1/4" 1/4" - - X 1/4" *GBP2480 3/16" 1/4" 1/4" 1/4" 1/4" 1/4" X 1/4" *GBP4801B X 3/8" X X X X 5/16" X Tool Multi-Grip Lockbolt GAGE BILT...committed to solutions Fasteners To Tool Recommendation Chart ********* Tool recommended is the most cost effective solution ********* "-" indicates the tool will install that fastener but is not the most cost effective solution. All tools will install a variety of fasteners. Refer to tool flyer for a complete list of fasteners that the tool will install. "X" indicates the tool is not recommended for that fastener. Lockbolt Commercial Blind Rivets MOST TOOLS AVAILABLE WITH PISTOL GRIP (SH) AND IN-LINE SPLIT SYSTEMS (SR) AND/OR VACUUM COLLECTOR SYSTEMS. Commercial Lockbolts Blind Oversized Mandrel Container Bolt C50L Huck Fit HP8 MHP10.9 GBP713C 1/4" - X 3/8" X X X X GBP745D 5/16" 5/16"-3/8" Alloy 1/4" - X X X X GBP752E 3/16" 3/16"-1/4" X X X X X X *GBP2480 3/16"-1/4" 5/32-"1/4" 1/4" 3/8" X X X X *GBP4801B 3/8" 5/16"-3/8" 5/16"-3/8" - X X X X *GBP585 X X X X X X X 16mm-20mm *GBP7624B X X X X 1/2"-3/4" 1/2"-3/4" 1/2"-3/4" 12mm-16mm *RECOMMENDED FOR HIGH PRODUCTION APPLICATIONS. GBP940 (ELECTRIC) OR GBP910C (AIR) POWERUNIT IS REQUIRED. 9/08
4 Tool NAS9301- NAS9312 GAGE BILT...committed to solutions Fasteners To Tool Recommendation Chart ******** Tool recommended is the most cost effective solution ******** "-" indicates the tool will install fastener but is not the most cost effective solution. All tools will install a variety of fasteners. Refer to tool flyer for a complete list of fasteners that the tool will install. "X" indicates the tool is not recommended for that fastener. NAS1919S & U NAS1921S & U MS21140S & U MS21141S & U Aerospace Blind Rivets NAS1398 NAS1399 NAS1738 NAS1739 NAS1398A NAS1399A NUTPLATE GROUND STUD NAS1719 NAS1720 NAS1721 MBC 2 ASP ASP FF ASP F ASP LC GB51 1/8" 1/8" X X 3/32"-1/8" 3/32"-1/8" X 3/32"-1/8" X GBP751D - 5/32"-3/16" 5/32" X 5/32"-3/16" /32"-3/16" 13/64" GBP704F 5/32"-3/16" - - X GBP713C - 1/4" 1/4" X 1/4" - - 1/4" 21/64" GBP745D - - 5/16" X - X - 1/4" - GBP752E 1/4" - 3/16" /64" GBP784B X X X 1/8"-1/4" X X X X X *GBP2480 1/8"-1/4" 1/8"-1/4" 5/32"-1/4" X 3/32"-1/4" 3/32"-1/8" -8 & -10 3/32"-1/4" 13/64"-21/64" *GBP4801B - - 5/16"-3/8" X **GBP X - X **GBP205 X X - X X X X X X **GBP7XX X **GBP5XX X X - X X X X X X MOST TOOLS AVAILABLE WITH PISTOL GRIP (SH) AND IN-LINE SPLIT SYSTEMS (SR) AND/OR VACUUM COLLECTOR SYSTEMS. GBP204 AND GBP205 HYDRAULIC INSTALLATION TOOLS ARE RECOMMENDED FOR OFFSET AND CLOSED ACCESS APPLICATIONS. Tool Lightweight Groove Proportioned Lockbolt Aerospace Lockbolts Groove Proportioned Lockbolt Metric Lightweight Groove Proportioned Lockbolt Metric Groove Proportioned Lockbolt NAS TENSION NAS SHEAR GBP731 1/8"-1/4" 1/8"-1/4" 4mm-5mm 4mm-6mm 1/8"-1/4" 1/8"-1/4" GBP745D 5/16" 1/4"-5/16" 6mm-8mm 6mm-8mm 1/4"-5/16" 1/4"-5/16" *GBP2480 1/8"-1/4" 1/8"-1/4" - 4mm-6mm 1/8"-1/4" 1/8"-1/4" *GBP4801B 5/16"-3/8" 5/16"-3/8" 8mm-10mm 8mm-10mm 5/16"-3/8" 5/16"-3/8" **GBP **GBP *RECOMMENDED FOR HIGH PRODUCTION APPLICATIONS. GBP940 (ELECTRIC) OR GBP910A (AIR) POWERUNIT IS REQUIRED. GBP204 AND GBP205 HYDRAULIC INSTALLATION TOOLS ARE RECOMMENDED FOR OFFSET AND CLOSED ACCESS APPLICTIONS 9/08
5 GAGE BILT riveting solutions Fasteners to Tools Selection Chart (Commercial Lockbolts) TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Multi Grip Lockbolt 3/16" GBP752E MG /4" GBP713C MG /16" GBP745D MG /8" GBP4801B MG NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Lockbolt 3/16" GBP752E LB /4" GBP752E LB /16" GBP745D LB10-745C-26 1 NAS10-205A-31 3/8" GBP745D LB NAS12-205A FOR OFFSET NOSES TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER B O M 1/4" GBP745D BOM08-745C /16" GBP4801B BOM /8" GBP4801B BOM NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER C50L 1/2" GBP7624B NONE NONE 5/8" GBP7624B NONE NONE 3/4" GBP7624B NONE NONE NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER HP8 1/2" GBP7624B HP NONE NONE 5/8" GBP7624B HP NONE NONE 3/4" GBP7624B HP NONE NONE NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER MHP mm GBP7624B HP12MM NONE NONE 16mm GBP7624B HP NONE NONE 20mm GBP585 HP20MM NONE NONE NONE *Most straight noses are available in short, medium and long lengths. 1) Contact Gage Bilts Engineering department for specific tool information. 9/08 GAGE BILT GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
6 GAGE BILT riveting solutions Fasteners to Tools Selection Chart (Commercial Blind Rivets) TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Open End Nail 3/32" GB51 3N-715E-43 3N RA 3N OS 1/8" GB51 4N-715E-43 4N-715A-44 4N-715A-40OS 5/32" GBP703E 5N /16" GBP703E 6N /4" GBP743C 8N-743A NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Monobolt 3/16" GBP703E MB06-734A /4" GBP743C MB08-734A NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER T Rivet 3/16" GBP703E 6T /4" GBP743C 8T-743A NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Closed End 3/32" GB51 3N-715E-43 3N RA 3N OS 1/8" GB51 4N-715E-43 4N RA 4N OS 5/32" GBP703E 5N N-352A-54RA 1 3/16" GBP703E 6N N-352A-54RA 1 NONE /4" GBP743C 8N-743A NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Klamptite 3/16" GBP724A 6KT-743A /4" GBP724A 8KT-743A NONE Plastic Split 3/16" GBP703E 6P /4" GBP703E 8P NONE Avseal 10mm GBP752E ASM NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Multi-Grip Structural 3/16" GBP703E PH6-734A /4" GBP743C PH NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER FloorTight 5/16" GBP4801B FT10-745B NONE TYPE DIAMETER INSTALLATION TOOL *STRAIGHT RIGHT ANGLE OFFSET ADAPTER Container 3/8" GBP713C HT NONE *Most straight noses are available in short, medium and long lengths. 1) Contact Gage Bilts Engineering department for specific tool information. 9/08 GAGE BILT GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
7 GAGE BILT Tool Adapters Adapter Adapts Nose Assembly To Tools XX-701, XX-704, XX-753 & XX-763 Series Nose Assemblies to Tool Models: 352, G83 & G84 XX-205 Series Nose Assemblies to Tool Models: GBP745D* & GBP4801B* XX-206 and Huck & Series Nose Assemblies to Tool Models: GBP745C* & GBP4801B* Extends XX-703, XX-734 & XX-743 Series Nose Assemblies 2" Extends XX-703, XX-743 & XX-743 Series Nose Assemblies 6" /4" Series Nose Assemblies to Tool Models: GBP703E*, GBP724* & GBP743C* XX-715B & XX-51 Series, Nose Assemblies to Tool Models: GBP704F* Extends XX-704, XX-704, XX-753 & XX-763 Series Nose Assemblies 2" Extends XX-704, XX-704, XX-753 & XX-763 Series Nose Assemblies 4" Extends XX-704, XX-704, XX-753 & XX-763 Nose Assemblies 6" Extends XX-704, XX-704, XX-753 & XX-763 Series Nose Assemblies 12" 456MAX (Straight), 456MAX OS (Offset) & 456MAX-753A-54 (Right Angle) Nose Assemblies to Tool Models: GBP784B* Extends XX-715B & XX-51 Series Nose Assemblies 2" XX-715B & XX-51 Series Nose Assemblies to Tool Models: GBP752E*, GBP730E*, GBP731, GBP722 & GBP713C* XX-715B & XX-51 Series Nose Assemblies to Tool Models: GBP740A* XX-701, XX-704, XX-753 & XX-763 Series Nose Assemblies to Tool Models: GBP744E* XX-204 Series Nose Assemblies to Tool Models: GBP730E*, GBP751C*, GBP731, GBP722 & GBP713C* XX-701, XX-704, XX-753 & XX-763 Series Nose Assemblies to Tool Models: GBP730E*, GBP751C*, GBP752E*, GBP731, GBP722, GBP713C* & GBP2480 XX-715B & XX-51 Series Nose Assemblies to Tool Models: GBP784B* /4" Series Nose Assemblies to Tool Models: GBP745D*, GBP4801B* & GBP XX-204 SERIES NOSE ASSEMBLIES TO TOOL MODELS: G83A & G84A *Tool Model Revision or Above
8
9 200 GAGE BILT... fastening solutions for the 21 st century Nose Assembly Data Sheet Key LB indicates a nose assembly for lockbolts. 08 is the fastener size (in 32nds of an inch, LB /32 =1/4 ). 713 is the tool it may be used on. This is not the only tool. Most nose assemblies may be used on a variety of tools. 20 is the approximate length, or gun line, from the tool in tenths of inches. In this case, 2.0 inches Prefix codes refer to the type of fastener: A LB LGP MAX MB MG MGL MGP MLGP N NAS SB SMLS UBR - A Code Rivet -Lockbolt -Lightweight Groove Proportioned -M7885/NAS Monobolt -Multi-Grip Lockbolt -Multi-Grip Blind Fastener -Metric Groove Proportioned -Metric Lightweight Groove Proportioned -Nail or Pop Rivet -NAS Tension or Shear Lockbolt -Single Action Blind Bolt -NAS1919S & 1921S -NAS1919U & 1921U
10
11 HOW A RIVET WORKS As the trigger is pulled, hydraulic pressure in the tool forces the piston and collet to begin to retract (figure 5). As this action first occurs, the jaws do not retract, instead they are continually forced forward by the jaw spring and follower. As the collet further retracts, the jaws are pulled back away from the nose tip. As this opposing movement occurs, the cone angle in the collet causes the jaws to close onto the rivet pintail. Once the jaws have a firm grip on the pintail (figure 6), the pulling action on the pintail pulls the pintail head into the core of the rivet body causing the rivet body to expand. As this movement continues, the pintail head reaches a certain resistance that is greater than that of the break-neck. At this point, a strong, tight joint is formed. The pintail breaks away and the rivet is set. (Figure 7) When the trigger is released, the piston, collet, jaws, jaw spring, and jaw follower are returned forward by air pressure to their full forward position. The jaws still grip the broken pintail until they contact the back of the nose tip. They are then forced open and release the pintail. Vacuum (if equipped) then pulls the broken pintail out of the nose assembly.
12 GAGE BILT GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp., Mi (586) Fax / Nail Rivet (open end) Avdel- Cherry (N) Closed End Rivet Monobolt (Avdel) Magna-Lok (Huck Ultra-Grip (POP) T Rivet / Peel Rivet Hemlock
13 C6L / Avdelok Magna-Grip (Huck) / Maxlock (Avdel) Avtainer / Hucktainer (Container Bolt) BOM
14 Klamp-Tite Bulb-Tite Av-Seal / Av Plug Floortite Sleeve Bolt XXX GO TO: FOR FLYERS, NOSE ASSEMBLIES AND RECOMMENDATIONS FOR INDIVIDUAL APPLICATIONS
15 GAGE BILT LOCKBOLT INSTALLATION TOOLS FOR THE RAILROAD INDUSTRY SINCE 1956 GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax /
16 LOCKBOLT INSTALLATION TOOLING GBP7624B/GBP7624B(A) GBP745D The GBP7264B is a hydraulic installation tool capable of installing 1/2", 5/8" and 3/4" C50L or HP8 lockbolts. It weighs 15 lbs and can be operated in any position with one hand. It has a 1.970" rivet setting stroke and a rated pull load of 40,000 lbs.. The GBP7624B operates on GAGE BILT and HUCK air or electric powerunits NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY. GBP585/GBP585A The GBP585 is a hydraulic installation tool capable of installing 5/8" and 3/4" C50L or HP8 lockbolts. It weighs just under 20 lbs. and is our most powerful hand tool. It has a 1.600" rivet setting stroke and a rated pull load of 40,000 lbs. The GBP585 operates on GAGE BILT and HUCK air or electric powerunits NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY. The GBP745D is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets, lockbolts and MAGNA-GRIP fasteners. It weighs just over 7 lbs. and can be operated in any position with one hand. It has a.600" rivet setting stroke and a rated pull load of 6300 lbs. with 90 psi air pressure at the air inlet. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY. GBP4801B/GBP4801B(A) The GBP4801B is a hydraulic installation tool designed specifically for the efficient installation of a wide range of lockbolt and Magna-Grip fasteners thru 3/8" diameter. It weighs just under 8 lbs. and can be operated in any position with one hand. It has a 1.000" rivet setting stroke and a rated pull load of 11,000 lbs.. The GBP4801B operates on GAGE BILT and HUCK air or electric powerunits. POWERUNITS AIR, ELECTRIC & FOOT OPERATED NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY. GBP2480/GBP2480A The GBP2480 is a hydraulic installation tool designed specifically for the efficient installation of a wide range lockbolts and Multi-Grip fasteners thru 1/4" diameter. It weighs just over 3 lbs. and is operated in any position with one hand. It has an.875 rivet setting stroke and rated pull load of 5600 lbs. The GBP2480 operates on GAGE BILT and HUCK air or electric powerunits. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY. GBP910D GBP940 GBP902 9/08
17 GAGE BILT Lockbolt and blind rivet installation tools Fastening solutions for the 21 st century ORDER INFORMATION 1. Minimum net order: U.S. = 75.00; Outside U.S. = $ F.O.B: Clinton Township, MI 3. Terms: Net 30 days 4. There is a $75.00 minimum or 20% whichever is greater, restocking charge. 5. Shortages must be reported within 48 hours of delivery hour/expedited service is available on most nose assemblies and tool. There is a $75.00 minimum or 10%, whichever is greater, additional charge. 7. ALL PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. 8. Drawings of all noses assemblies, installation tools and powerunits are available at or call inside sales for specific information. WARRANTY Seller warrants that all goods covered by this catalog will conform to applicable specifications and drawings and will replace, or repair, F.O.B. our plant, any goods proving defective from faulty workmanship, or material, for 90 days from date of shipment. Said warranty to remain in effect if and only if such goods are used in accordance with all instructions as to maintenance, operation, and use set forth in manuals and instruction sheets furnished by Seller. Seller's obligation under this warranty shall be limited to the repair or rework of the goods supplied or the replacement thereof, at Seller's option, and in no case is to exceed the invoice value of said goods. Under no circumstances will Seller be liable for incidental or consequential damages or for damages incurred by the buyer or subsequent user in repairing or replacing defective goods or if goods covered by this warranty are reworked or subjected to any type of additional processing. This warranty is void if Seller is not notified in writing of any rejections or defects within 90 days after receipt of the material by customer. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY. GAGE BILT PRODUCTS CORP Centre Ct. Clinton Twp MI solutions@gagebilt.com Phone (586) Fax (586)
18
19 GB51 PNEUMATIC INSTALLATION TOOL 2.64 Ø DESCRIPTION The GB51 pneumatic riveter is designed specifically for the most efficient installation of a wide range of blind rivets. It will install aluminum rivets through 3/16" diameter, and through 1/8" diameter rivets in any material. It weighs only 2 1/2 lbs. and can be operated in any position with one hand. The GB51 Riveter is 7" high, has a.740 stroke and generates a minimum of 1000 lbs. of pull at 90 psi. It operates from 80 to 110 psi of air pressure at the tool. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS TOOL AND MUST BE PURCHASED SEPARATELY. GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
20 GB51 SELECTION CHART DIA. STRAIGHT RIGHT ANGLE 1, 6 OFFSET NUT PLATE RIVETS 3/32 3C-715B-43 3C RA 3C OS MS20600 SERIES 1/8 4C-715B-43 4C RA 4C OS CCR244/264/274 5/32 3 MS/9SP/PT 5C-715B-43 5C RA 5C OS BACR15CC/CF/DA/DR 3/16 3 6C-715B-43 6C RA 6C OS 3/32 3A-715B-43 3A RA 3A OS "A" CODE 1/8 4A-715B-43 4A RA 4A OS NAS1398A, NAS1399A 5/32 3 NAS1740A, NAS1739A 5A-715B-43 5A RA 5A OS 3/16 5 6A-715B-43 6A RA 6A OS SINGLE ACTION BLIND RIVET 1/8 SMLS04-715B-43 SMLS RA SMLS04-715A-40OS NAS1919S & U 5/32 3 SMLS05-715B-43 SMLS RA SMLS05-715A-40OS NAS1921S & U 3/16 3 SMLS06-715B-43 SMLS RA SMLS06-715A-40OS BACR15FR/FP, BACR15GF/GK, NAS1919S & U & NAS1921S & U "U" TYPE BLIND RIVET WITH LOCKING WASHER NAS N, Q & E POP, CLOSED END AVEX & COMMERCIAL RIVETS 1/8 5/32 3 3/ MAX MAX-715A-54RA 2 456MAX OS 2 3/32 3N-715E-43 3N RA 3N OS 1/8 4N-715E-43 4N RA 4N OS 5/32 3 5N-715E-43 5N RA 5N OS 3/16 3 6N-715E-43 6N RA 6N OS THE GAGE BILT GB51 TOOL IS APPROVED TO INSTALL THE ABOVE S. 1) RIGHT ANGLE S MAY REQUIRE MORE THAN ONE PULL. 2) INSTALLS 1/8, 5/32 & 3/16 DIAMETERS. 3) ALUMINUM ONLY. 4) ALUMINUM & STEEL ONLY. 5) SELF-PLUGGING ALUMINUM ONLY 6) RIGHT ANGLE S REQUIRE STROKE LIMITER. *ALL COUNTERSUNK 'C' NOSE ASSEMBLIES MAY BE USED TO INTSALL BOTH UNIVERSAL & COUNTERSUNK HEAD RIVETS NOTE: THE LAST 2 DIGITS OF THE REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES Rev.11/08
21 GB8000 SERIES AUTO FEEDER Gage Bilts 8000 series semi-automated riveting systems use a hand held pistol grip or an in-line installation tool. The tool comes with a 8 foot umbilical connected to a hydraulic power unit. The tool and power unit work cooperatively with a vibratory bowl, escapement and plc controller built into a base unit of 28"x16"x14". The unit automatically presents rivets to the nose tip from the feeder with air. The rivet is then pulled into the tool via a vacuum system that also provides for the discharge of the spent pintails. The unit requires 110 vac, 80 psi minimum, with 10 CFM of compressed air. This system is capable of a feed rate of 45 rivets a minute. Contact our engineering department for specific applications. A video of this system is available at GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
22 NEST ASSEMBLY FEEDER ARM ASSEMBLY NOSE TIP NOSE ASSEMBLY VACUUM TUBE TRIGGER FILTER REGULATOR ASSEMBLY BOOSTER VALVE ASSEMBLY ELECTRICAL ENCLOSURE VACUUM COLLECTION FRONT OF BASE AND FRAME FEED TRACKS AND ESCAPEMENT VIBRATORY BOWL Rev. 1/07
23 GBP585 HYDRAULIC INSTALLATION TOOL 4.38 Ø Ø Ø DESCRIPTION The GBP585 is a hydraulic installation tool capable of installing 5/8" and 3/4" HP8 or standard lockbolts. It weighs just under 20 lbs. and is our most powerful hand tool. It has a 1.600" rivet setting stroke and a rated pull load of 40,000 lbs. The GBP585 installation tool operates on hydraulic pressure developed by the GBP940 Powerunit set at psi PULL pressure and psi RETURN pressure. The tool comes equipped with 24" hoses and electric cord kit complete with quick disconnects. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY. GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
24 GBP585 SELECTION CHART DIA. LOCKBOLT HIGH TENSILE PULL TYPE 5/ C5OL 3/ BLIND OVERSIZE MANDREL 5/8 BOM /4 BOM HP8 5/8 HP /4 HP MHP MM HP * 20MM 1 HP20MM *FOR NON-PRODUCTION APPLICATIONS ONLY 1) POWER UNIT REQUIRES ADJUSTMENT TO 7,200 PSI FOR PULL AND 4,000 PSI FOR RETURN KEY A ~The first numerical digit represent the diameter of the fastener in 32nds of an inch. (20/32) B ~The second set of digits represent ONE of the tool models which MAY be used with this head. (Model 585) C ~The last set of numerical digits signify the Gun Line, or reach of the pulling head to the nearest tenth of an inch. (41 is 4.1 inch Gun Line ) Rev. 4/07
25 GBP585MFK Millimeter Framebolt Kit Installs HUCK 10.9 and Metric Huck-Fit Truck Framebolts INCLUDES: GBP air operated manual Hydraulic Powerunit with 12 hoses. GBP585ANT Hydraulic Installation Tool. HP12MM mm Nose Assembly. HP mm Nose Assembly. HP20MM mm Nose Assembly. GAGE BILT is now offering a new product for truck and trailer repair facilities, the GBP585MFK. It s a low cost solution for frame repair. The GBP585MFK incorporates GAGE BILTS new GBP902 air operated powerunit. Just plug it into shop air and you re ready to put in HUCK 12mm, 16mm and 20mm 10.9 metric Huck-Fit truck framebolts. The nose for the 16mm also installs Huck HP8 5/8 framebolts in your Pete or KW. The GBP585ANT installation tool is included, as well as a 12 hose kit. The power unit is a manual foot pedal operated hydraulic power source that delivers 5,700 psi pull and return pressure with 65 psi air pressure connected to the power unit and is adjustable for higher pressures. CAUTION: Always consult tool manual before resetting any pressures. The air pressure to the unit controls the output and return pressure to the tool and must be properly adjusted for each tool. If pressures are not adjusted properly severe personal injury may result. GAGE BILT MADE IN U.S.A. 9/08 GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp, MI (586) Fax solutions@gagebilt.com /
26
27 GB585MTFK Installation Kit Installs HUCK 10.9 and Huck-Fit Truck Frame Bolts INCLUDES: GBP910C-12 air operated Hydraulic Powerunit with 12 hoses. GBP585A Hydraulic Installation Tool. HP12MM mm Nose Assembly. HP mm Nose Assembly. HP20MM mm Nose Assembly. GAGE BILT 9/08 GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. Mi (586) Fax /
28
29 GBP703E SERIES INSTALLATION TOOLS 1.56 Ø (39.6mm) 1.14 Ø (28.9mm) 8.10 (205.8mm) (157.1mm) (55.1mm) GBP703E Stroke -.780" Hand held weight lbs. Entire tool weight lbs Pull load - 2, (45.2mm) 1.25 (31.75mm).87 (22.1mm) 1.90 (48.2mm) 4.12 (104.6mm) 3.88 Ø (98.5mm) 5.07 (128.7mm) 7.08 [179.75mm] 4.04 GBP703ESH Stroke -.800" Hand held weight lbs. Entire tool weight lbs Pull load - 2,200 GBP703ESR Stroke -.780" Hand held weight lbs. Entire tool weight lbs Pull load - 2, (249.4mm) 4.15 (105.3mm) 5.07 (128.7mm) GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
30 DESCRIPTION The GBP703E series are pneumatichydraulic tools designed specifically for the efficient installation of a wide range of blind rivets. They can be operated in any position with one hand. They have a rated pull load of 2200 pounds with 90 psi air pressure at the air inlet. The GBP703ESH and GBP703ESR riveters offer a unique split system providing the operator with an ergonomic tool with reduced hand held weight, as shown below. The GBP703E series riveters operate on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 lbs air pressure, the GBP703E series does not exceed 85 db (A) and consumes 3 cfm at 20 cycles a minute. The GBP703E series riveters are furnished with nose assembly 6N and spare nose tip and follower to convert to 4N nose assembly. OPTIONS The GBP703E series riveters may be ordered with a vacuum system. Gage Bilt offers two varieties (see below) GBP703E SERIES SELECTION CHART RIVET DIA. NOSE TIP 1 JAW FOLLOWER DESIGNATION AVEX (1624 PROTRUDING HEAD) 3/16 AV6-743A AV6 AVEX (1624COUNTERSUNKHEAD) 3/16 6C-743A C KLAMPTITE (STRUCTURAL) RIVET 3/16 6KT KT 1/4 8KT-743A KT MACHINE SCREW RIVET 5MM MS5M MM MONOBOLT RIVET 3/16 MB06-734A-20 2, MB06 1/4 3 MB , MB08 NUTPLATE RIVET CCR244/264/274 3/32 3NP NP BACR15DR MS /8 5N N 3/32 3N N OPEN END 1/8 4N N CLOSED END NAIL RIVET 5/32 5N N 3/16 6N N 1/4 3 8N-743A N 3/32 3P P 1/8 4P P PLASTIC SPLIT RIVET 5/32 5P P 3/16 6P P 1/4 8P-743A P T RIVET 3/16 6T T 1/4 3 8T-743A T TLR RIVET 1/4 8TLR-743A TLR SELECTION CHART FOR PROTRUDING HEAD ONLY RIVET DIA. NOSE TIP 1 JAW FOLLOWER DESIGNATION SERRATED STEM 3/16 PH6-734A-20 2, PH6 STRUCTURAL RIVET 1/4 4 PH ,3, PH8 1) YOU CAN CHANGE THE NOSE ASSEM BLY (INCLUDED WITH TOOL) TO INSTALL OTHER S BY PURCHASING NOSE TIP SHOWN AND USING APPROPRIATE FOLLOWER SHOWN. 2) NOSE ASSEMBLIES WITH A DESIGNATION, I.E. 8N-743A-24, MUST BE ORDERED AS COMPLETE. 3) ALUMINUM RIVET STEEL MANDREL ONLY (100 PSI REQUIRED FOR ALL 1/4" STEEL RIVETS). 4) 1/4" ALUMINUM ONLY. 5) NOSE ASSEMBLIES WITH A 734 DESIGNATION, I.E. PH , ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH AND SERRATED STEM RIVETS YOU MUST ORDER THE WITH A 743 DESIGNATION, I.E. MGL NOTE: THE LAST 2 DIGITS OF THE REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES Order GBP703E series riveters with the proper rivet specification by adding the appropriate suffix (see selection chart). V DESIGNATION = PINTAIL COLLECTOR BOTTLE VT DESIGNATION = PINTAIL EVACUATION TUBE HOW TO ORDER GBP703 SERIES TOOLS TOOL SERIES SH - SPLIT HANDLE MODEL SR - SPLIT RIVETER MODEL NO DESIGNATION - STANDARD MODEL GBP703E SH V / 6N 6N - RIVET SPECIFIC DESIGNATION (SEE SELECTION CHART) NO DESIGNATION - STANDARD V - VACUUM W/ COLLECTOR BOTTLE VT - VACUUM W/ EVACUATION TUBE NO DESIGNATION - NO VACUUM 11/08
31 GBP722 INSTALLATION TOOL 1.94 Ø (49.2mm) 1.36 Ø (34.5mm) 1.80 (45.7mm) 7.14 (181.4mm) 4.33 (110mm) 1.25 (31.8mm) (320mm) 1.92 (48.8mm) 5.16 (131mm) 3.88 Ø (98.6mm) 5.07 (128.8mm) DESCRIPTION The GBP722 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets. It weighs 5.50 lbs. and can be operated in any position with one hand. It has a.590" rivet setting stroke and a rated pull load of 4700 pounds with 90 psi air pressure at the air inlet. The GBP722 riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 lbs air pressure, the GBP722 does not exceed 85 db (A) and consumes 3 cfm at 20 cycles a minute. The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting. NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY. GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp, MI (586) Fax solutions@gagebilt.com /
32 SELECTION CHART FOR GBP722 DIA. STRAIGHT *RIGHT ANGLE 2 COMMERCIAL LOCKBOLTS MULTIGRIP LOCKBOLTS MS90353S & U & MS90354S & U MS21140S & U & MS21141S & U CR7000 SERIES BACB30YY, YU, & YT MS90353 & MS90354 MS21140 & MS21141 "U" TYPE BLIND BOLT WITH DRIVE WASHER **OFFSET 3/16 LB LB /4 LB LB /16 MG MG /4 MG MG /32 SB05-752B-20 SB05-752B-45 SB05-751B-54RA SB05-752A-43OS SB05-752B-80 3/16 SB06-752B-20 SB06-752B-45 SB06-751B-54RA 5 SB06-204C-27OS SB06-752B-80 1/4 4 SB SB SB08-204C-27OS 4 SB08-204C-37OS 4 5/32 UBB05-752B-20 UBB05-752B-45 UBB05-751B-54RA UBB05-752A-43OS 3/16 UBB06-752B-20 UBB06-752B-45 UBB06-751B-54RA 5 UBB06-752A-43OS 1/4 4 UBB UBB UBB08-204C-27OS 4 UBB08-204C-27OS 4 EN6122 & UAB130-EU EN6127 & UAB6127-EU EN6128 & UAB100-EU EN6129 & UABP-EU SINGLE ACTION BLIND RIVET NAS1919S & U NAS1921S & U "A" CODE NAS1398A & NAS1399A PROTRUDING HEAD, MULTI-GRIP BLIND RIVETS COUNTERSUNK HEAD, MULTI-GRIP BLIND RIVETS MONOBOLT CONTAINER BOLT(R 12) HLPP, HLPM, HLPE, HLPS HLPSC & HLPSM BACR15FR/FP, BACR15GF/GK, NAS1919 & NAS1921 "U" TYPE BLIND RIVET WITH DRIVE WASHER NAS ASP 2, ASP PF, ASP 4 FF, ASP 2 F, ASP 2 LC NAS1719, NAS1720 NAS1721 GROUND STUD, M83454 & BACS53B 1/8 UAB04-752B-20 UAB04-752B-45 UAB04-751B-54RA UAB04-752A-43OS 5/32 UAB UAB UAB05-751B-54RA UAB05-752A-43OS 3/16 UAB06-751B-54RA 5 UAB06-752A-43OS 1/4 UAB08-204C-27OS UAB08-204C-37OS 1/8 SMLS04-752B-20 SMLS04-752B-45 SMLS04-751B-54RA SMLS04-752A-43OS 5/32 SMLS05-752B-20 SMLS05-752B-45 SMLS05-751B-54RA SMLS05-752A-43OS 3/16 SMLS06-752B-20 SMLS06-752B-45 SMLS06-751B-54RA SMLS06-752A-43OS 1/4 SMLS SMLS SMLS08-751B-54RA SMLS08-204C-27OS SMLS08-204C-37OS 3/32 3A-352B-25 3A-751B-54RA 1/8 4A-752B-20 4A-752B-45 4A-751B-54RA 4A-752A-43OS 5/32 5A-752B-20 5A-752B-45 5A-751B-54RA 5A-752A-43OS 3/16 6A-752B-20 6A-752B-45 6A-751B-54RA 6A-752A-43OS 1/4 SMLS SMLS SMLS08-751B-54RA 5 SMLS08-204C-27OS SMLS08-204C-37OS 3/16 MGL06-752A-21 6 MGL06-752A-61 6 MGL06-751B-54RA 6 1/4 MGL08-752A-21 6 MGL08-752A /16 6CN-752A CN-752A /4 8CN-752A CN-752A /16 MB06-752A-21 6 MB06-752A-61 6 MB06-751B-54RA 6 1/4 MB08-752A-21 6 MB08-752A /8 HT /8 456MAX-751A MAX-751A MAX-751C-54RA 1 456MAX OS 1 5/32 3/16 1/4 08MAX-752B-20 08MAX-752B-45 08MAX-204C-27OS 08MAX-204C-37OS 13/64 ASP06-752B-20 ASP06-752B-45 ASP06-751B-54RA ASP06-752A-43OS 17/64 ASP08-752B-20 ASP08-752B-45 ASP08-751B-54RA ASP08-752A-43OS 21/64 ASP ASP ASP10-204C-27OS ASP10-204C-37OS 1/8 MBC04-752B-20 MBC04-752B-45 MBC04-751A-54RA MBC04-752A-43OS 5/32 MBC05-752B-20 MBC05-752B-45 MBC05-751A-54RA MBC05-752A-43OS 3/16 MBC06-752B-20 MBC06-752B-45 MBC06-751A-54RA MBC A43OS 8/32 GS8-752B-20 GS8-752B-45 GS8-751B-54RA GS8-752A-43OS ` 10/32 GS10-752B-20 GS10-752B-45 GS10-752A-54RA GS10-752A-43OS THE GAGE BILT GBP722 IS APPROVED TO INSTALL THE ABOVE S. *ALL RIGHT ANGLE NOSE ASSEMBLIES REQUIRE STROKE LIMITER. **ALL OFFSET 204 SERIES NOSES REQUIRE ADAPTER. 1) INSTALLS 1/8 5/32 & 3/16 DIAMETERS 2) RIGHT ANGLE NOSE ASSEMBLIES MAY REQUIRE MORE THAN ONE PULL. 3) INSTALLS 5/32, 3/16 & 1/4 DIAMETERS. 4) 105 PSI REQUIRED FOR ALLOY STEEL. 5) THESE NOSES FOR LIGHT DUTY / REPAIR ONLY. 6) 2 PULLS REQUIRED FOR MOST APPLICATIONS. NOTE: THE LAST 2 DIGITS OF THE REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES Rev. 11/08
33 Introducing the GBP722TCK Trailer and Cab Kit Choose GAGE BILTS blind rivet and lockbolt installation kit designed especially for Truck and Trailer OEM s. The GBP722TCK can be configured to meet your needs, whether you re fixing Wabash, Great Dane, Peterbilt, Kenworth or any other brand trailer or truck. The kit includes nose assemblies to pull your fasteners, and at the heart of the system is our heavy-duty GBP722 installation tool. All of this is conveniently stored in a metal tool case. The GBP722TCK kit comes with a nose and 2 tips to install 3/16 and 1/4 structural blind rivets in any material, a catcher bag for pintails, a 3/16 nose for the stainless steel grill bolt, and a 3/16 & 1/4 Magna-Grip nose for the hood and cab. If additional noses are needed please consult Gage Bilt. GAGE BILT MADE IN U.S.A. Rev. 11/08 GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
34 GBP722TCK BLIND RIVETS (2 PULLS REQUIRED FOR MOST APPLICATIONS) 3/16" 1/4" ALUMINUM, STEEL OR STAINLESS STEEL MAGNA-LOK BLIND RIVET ALUMINUM, STEEL OR STAINLESS STEEL MAGNA-LOK BLIND RIVET.750 Ø MGLC68-752A-21 (USE NOSE TIP) MGLC68-752A-21 (USE NOSE TIP) MGL68-752A-21 LOCKBOLTS 3/16" STAINLESS STEEL C6L 3/16" STEEL C6L LB /16" ALUMINUM C6L 3/16" STEEL MAGNA-GRIP MG /16" ALUMINUM MAGNA-GRIP 1/4" STEEL MAGNA-GRIP MG /4" ALUMINUM MAGNA-GRIP *NOSES LISTED PROTRUDE 2 INCHES FROM THE TOOL. LONGER NOSES ARE AVAILABLE..750 Ø LB Ø Ø MG MG Rev. 11/08
35 GBP724A SERIES INSTALLATION TOOLS 1.94 Ø (49.3mm) 1.36 Ø (34.5mm) 2.92 (74.1mm) 6.77 (717.9mm) 8.70 (221.2mm) GBP724A Stroke -.688" Hand held weight lbs. Entire tool weight lbs Pull load - 4, (46.7mm) 1.25 (31.8mm).87 Ø (22.0mm) 1.92 (48.8mm) 5.17 (131.2mm) 3.88 Ø (98.6mm) 5.07 (128.7mm) 7.40 (188mm) 4.22 (107mm) GBP724ASH Stroke -.915" Hand held weight lbs. Entire tool weight lbs Pull load - 4,100 GBP724ASR Stroke -.688" Hand held weight lbs. Entire tool weight - 6 lbs Pull load - 4,100 GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
36 DESCRIPTION The GBP724A series are pneumatic-hydraulic tools designed specifically for the efficient installation of a wide range of blind rivets. They can be operated in any position with one hand. They have a rated pull load of 4100 pounds with 90 psi air pressure at the air inlet. The GBP724ASH and GBP724ASR riveters offer a unique split system providing the operator with an ergonomic tool with reduced hand held weight, as shown below. The GBP724A series riveters operate on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 lbs air pressure, the GBP724A series does not exceed 85 db (A) and consumes 3 cfm at 20 cycles a minute. The GBP724A series riveters are furnished with nose assembly 8N-743A-24 and spare nose tip to convert to 6N-743A-24. OPTIONS The GBP724A series riveters may be ordered with a vacuum system. Gage Bilt offers two varieties (see below) GBP724A SERIES SELECTION CHART RIVET DIA. NOSE TIP JAW FOLLOWER DESIGNATION AVEX (1624 PROTRUDING HEAD) 3/16 AV6-743A AV6 AVEX (1624COUNTERSUNKHEAD) 3/16 6C-743A C BULB-TITE (STRUCTURAL) RIVET 1/4 BT08-743A BT08 9/32 BT BT09 KLAMPTITE (STRUCTURAL) RIVET 3/16 6KT-743A KT 1/4 8KT-743A KT MACHINE SCREW RIVET 5MM MS5M-743A MM MONOBOLT RIVET 3/16 MB06-734A-20 2, MB06 1/4 MB , MB08 3/32 3N N OPEN END 1/8 4N N CLOSED END NAIL RIVET 5/32 5N N 3/16 6N-743A N 1/4 8N-743A N PLASTIC SPLIT RIVET 3/16 6P-743A P 1/4 8P-743A P T RIVET 3/16 6T-743A T 1/4 8T-743A T TLR RIVET 1/4 8TLR-743A TLR SELECTION CHART FOR PROTRUDING HEAD ONLY RIVET DIA. NOSE TIP JAW FOLLOWER DESIGNATION SERRATED STEM 3/16 PH6-734A-20 2, PH6 STRUCTURAL RIVET 1/4 PH , PH8 1) YOU CAN CHANGE THE 743 (INCLUDED WITH TOOL) TO INSTALL OTHER S BY PURCHASING NOSE TIP SHOWN AND USING APPROPRIATE FOLLOWER SHOWN. 2) NOSE ASSEMBLIES WITH A 743 AND 734 DESIGNATION, I.E. 5N , MUST BE ORDERED AS COMPLETE. 3) NOSE ASSEMBLIES WITH A 734 DESIGNATION, I.E. PH , ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH AND SERRATED STEM RIVETS YOU MUST ORDER THE WITH A 743 DESIGNATION, I.E. MGL06-743A-24. NOTE: THE LAST 2 DIGITS OF THE REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES Order GBP724A series riveters with the proper specification by adding the appropriate suffix (see selection chart) V DESIGNATION = PINTAIL COLLECTOR BOTTLE VT DESIGNATION = PINTAIL EVACUATION TUBE TOOL SERIES SH - SPLIT HANDLE MODEL SR - SPLIT RIVETER MODEL NO DESIGNATION - STANDARD MODEL GBP724A SH V / 8Z 8Z - RIVET SPECIFIC DESIGNATION (SEE SELECTION CHART) NO DESIGNATION - STANDARD V - VACUUM W/ COLLECTOR BOTTLE VT - VACUUM W/ EVACUATION TUBE NO DESIGNATION - NO VACUUM Rev. 11/08
37 GBP743C SERIES INSTALLATION TOOLS 1.94 Ø (49.2mm) 1.36 Ø (34.5mm) 9.00 (228.6mm) 6.74 (171.1mm) 2.95 (74.9mm) GBP743C Stroke -.900" Hand held weight lbs. Entire tool weight lbs Pull load - 4, (46.7mm) 1.50 (38.1mm).87 Ø (22.1mm) 2.25 (57.1mm) 4.79 (121.5mm) 4.88 Ø (123.9mm) 6.17 (156.7mm) 7.40 (188mm) 4.31 (109.4mm) GBP743CSH Stroke -.650" Hand held weight lbs. Entire tool weight lbs Pull load - 4,200 GBP743CSR Stroke -.900" Hand held weight lbs. Entire tool weight lbs Pull load - 4,200 GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
38 DESCRIPTION The GBP743C series are pneumatic-hydraulic tools designed specifically for the efficient installation of a wide range of blind rivets. They can be operated in any position with one hand. They have a rated pull load of 4200 pounds with 90 psi air pressure at the air inlet. The GBP743CSH and GBP743CSR riveters offer a unique split system providing the operator with an ergonomic tool with reduced hand held weight, as shown below. The GBP743C series riveters operate on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 lbs air pressure, the GBP743C series does not exceed 85 db (A) and consumes 3 cfm at 20 cycles a minute. The GBP743C series riveters are furnished with nose assembly 8N-743A-24 and spare nose tip to convert to 6N-743A-24. OPTIONS The GBP743C series riveters may be ordered with a vacuum system. Gage Bilt offers two varieties (see below) GBP743C SERIES SELECTION CHART RIVET DIA. NOSE TIP JAW FOLLOWER DESIGNATION AVEX (1624 PROTRUDING HEAD) 3/16 AV6-743A AV6 AVEX (1624COUNTERSUNKHEAD) 3/16 6C-743A C BULB-TITE (STRUCTURAL) RIVET 1/4 BT08-743A BT08 9/32 BT BT09 KLAMPTITE (STRUCTURAL) RIVET 3/16 6KT-743A KT 1/4 8KT-743A KT MACHINE SCREW RIVET 5MM MS5M-743A MM MONOBOLT RIVET 3/16 MB06-734A-20 2, MB06 1/4 MB , MB08 3/32 3N N OPEN END 1/8 4N N CLOSED END NAIL RIVET 5/32 5N N 3/16 6N-743A N 1/4 8N-743A N 3/32 3P P 1/8 4P P PLASTIC SPLIT RIVET 5/32 5P P 3/16 6P-743A P 1/4 8P-743A P T RIVET 3/16 6T-743A T 1/4 8T-743A T TLR RIVET 1/4 8TLR-743A TLR SELECTION CHART FOR PROTRUDING HEAD ONLY RIVET DIA. NOSE TIP JAW FOLLOWER DESIGNATION SERRATED STEM 3/16 PH6-734A-20 2, PH6 STRUCTURAL RIVET 1/4 PH , PH8 1) YOU CAN CHANGE THE 743A (INCLUDED WITH TOOL) TO INSTALL OTHER S BY PURCHASING NOSE TIP SHOWN AND USING APPROPRIATE FOLLOWER SHOWN. 2) NOSE ASSEMBLIES WITH A 743 AND 734 DESIGNATION, I.E. 5N , MUST BE ORDERED AS COMPLETE. 3) NOSE ASSEMBLIES WITH A 734 DESIGNATION, I.E. PH , ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH AND SERRATED STEM RIVETS YOU MUST ORDER THE WITH A 743 DESIGNATION, I.E. MGL06-743A-24. NOTE: THE LAST 2 DIGITS OF THE REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES Order GBP743C series riveters with the proper rivet specification by adding the appropriate suffix (see selection chart) V DESIGNATION = PINTAIL COLLECTOR BOTTLE VT DESIGNATION = PINTAIL EVACUATION TUBE HOW TO ORDER GBP743 SERIES TOOLS TOOL SERIES SH - SPLIT HANDLE MODEL SR - SPLIT RIVETER MODEL GBP743C SH V / 8Z 8Z - RIVET SPECIFIC DESIGNATION (SEE SELECTION CHART) NO DESIGNATION - STANDARD V - VACUUM W/ COLLECTOR BOTTLE VT - VACUUM W/ EVACUATION TUBE NO DESIGNATION - NO VACUUM Rev. 11/08
39 GBP745D INSTALLATION TOOL 2.31 Ø (58.7mm) 2.06 Ø (52.3mm) 5.63 (143mm) 8.58 (217.9mm) 1.50 Ø (38.1mm) 1.84 (46.7mm) 1.50 (38.1mm) 2.25 (57.2mm) 4.78 (121.6mm) 4.88 Ø (123.9mm) 6.17 (156.7mm) DESCRIPTION Covered under Patent No. 5,485,727 The GBP745D is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets, lockbolts and MAGNA-GRIP fasteners. It weighs just over 7 lbs. and can be operated in any position with one hand. It has a.600" rivet setting stroke and a rated pull load of 6300 pounds with 90 psi air pressure at the air inlet. The GBP745D riveter operates on a wide range of air pressure, with 90 to 120 psi providing the maximum efficiency. At 90 lbs. air pressure, the GBP745D does not exceed 82 db (A) and consumes 6.0 cfm at 20 cycles per minute. The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting. Nose Assemblies that were designed for the Model 353 Installation Tool mount directly on the GBP745D without the use of an adapter. Nose Assemblies that were designed for the Model 352 Installation Tool will attach to the GBP745D with the use of the nose assembly adapter. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS RIVETER AND MUST BE ORDERED SEPARATELY. GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp, MI (586) Fax solutions@gagebilt.com /
40 SELECTION CHART FOR GBP745D DIA. 1/8 4A-745B-23 4A-745B-48 4A-752A-43OS 'A' CODE 5/32 5A-745B-23 5A-745B-48 5A-752A-43OS NAS1398 & NAS1399 'A' NAS1438 & NAS1439 'A' 3/16 6A-745B-23 6A-745B-48 6A-752A-43OS 1/4 SMLS SMLS SMLS08-204C-27OS 2 ASP & ASP PF 13/64 ASP06-745B-23 ASP06-745B-48 ASP06-752A-43OS ASP FF & ASP F 17/64 ASP08-745B-23 ASP08-745B-48 ASP08-752A-43OS ASP-LC 21/64 ASP ASP ASP10-204C-37OS BLIND OVERSIZE MANDREL 1/4 BOM08-745C-23 3/16 NAS06-745B-12 NAS06-204B-25OS NAS06-204B-30OS NAS NAS NAS06-204B-34OS COMMERCIAL LOCKBOLTS 1/4 NAS08-745B-12 NAS08-204B-25OS C6L NAS08-204B-30OS ADVELOK NAS08-745B-23 NAS08-745B-48 NAS08-205A-31 NAS08-204B-34OS 5/16 1 LB10-745C-26 NAS NAS10-205A-31 3/8 5 LB NAS NAS12-205A-31 5/32 LGP05-745B-12 LGP05-204B-25OS LGP05-204B-30OS LGP LGP LGP05-204B-34OS LIGHTWEIGHT 3/16 LGP06-745B-12 LGP06-204B-25OS LGP06-204B-30OS GROOVE LGP LGP LGP06-204B-34OS PROPORTION 1/4 LGP08-745B-12 LGP08-204B-25OS LGP08-204B-30OS LOCKBOLTS LGP08-745B-23 LGP08-745B-48 LGP08-204B-34OS LGP08-205A-31 5/16 LGP10-745B-12 LGP LGP LGP10-205C-31 5/32 NASS05-745B-12 NAST05-745B-12 NASS05-204B-25OS NAST05-204B-20OS NASS NAST NASS05-204B-30OS NAST05-204B-30OS NASS NAST NASS05-204B-34OS NAST05-204B-34OS LOCKBOLT 3/16 NAS06-745B-12 NAS06-204B-25OS NAS06-204B-30OS NAS SHEAR PULL TYPE NAS NAS NAS06-204B-34OS NAS TENSION PULL TYPE 1/4 NAS08-745B-12 NAS08-204B-25OS NAS08-204B-30OS & GROOVE PORPORTION NASS = NAS SHEAR NAS08-745B-23 NAS08-745B-48 NAS08-204B-34OS NAS08-205A-31 NAST = NAS TENSION 5/16 NAS10-745B-12 NAS10-205A-31 NAS NAS /8 1 NAS12-745B-12 NAS12-205A-31 NAS NAS /16 MG MULTI-GRIP LOCKBOLT 1/4 MG /162 MG /8 3 MG MULIT-GRIP STRUCTURAL BLIND RIVET 3/8 MGL12-353C-28 9 PT/MS/9SP MS20600 & MS20601 BACR15FR/FP, BACR15GF/GK, NAS1919 & NAS1921 "U" TYPE BLIND RIVET WITH DRIVE WASHER NAS MS90353S & U & MS90354S & U MS21140S & U & MS21141S & U CR7000 SERIES BACB30YY, YU, & YT MS90353 & MS90354 MS21140 & MS21141 "U" TYPE BLIND BOLT W/ DRIVE WASHER EN6122 & UAB130-EU EN6127 & UAB6127-EU EN6128 & UAB100-EU EN6129 & UABP-EU SINGLE ACTION BLIND RIVET NAS1919S & U NAS1921S & U 1/4 1/8 456MAX-751A MAX-751A MAX OS 7 5/32 3/16 PT STRAIGHT 1/4 08MAX-745B-23 08MAX-745B-48 08MAX-204C-27OS 08MAX-204C-37OS 5/32 SB05-745B-23 SB05-745B-48 SB05-752A-43OS 3/16 SB06-745B-23 SB06-745B-48 SB06-752A-43OS 1/4 SB SB SB08-204C-27OS SB08-204C-37OS 5/16 4 SB SB SB10-205A-35 5/32 UBB05-745B-23 UBB05-745B-48 UBB05-752A-43OS 3/16 UBB06-745B-23 UBB06-745B-48 UBB06-204C-27OS 1/4 UBB UBB UBB08-204C-27OS UBB08-204C-37OS 5/16 4 UBB UBB UBB10-205A-35 1/8 UAB04-745B-23 UAB04-745B-48 UAB04-752A-43OS 5/32 UAB UAB UAB05-752A-43OS 3/16 UAB06-752A-43OS 1/4 UAB08-204C-27OS UAB08-204C-37OS 1/8 SMLS04-745B-23 SMLS04-745B-48 SMLS04-752A-43OS 5/32 SMLS05-745B-23 SMLS05-745B-48 SMLS05-752A-43OS 3/16 SMLS06-745B-23 SMLS06-745B-48 SMLS06-752A-43OS 1/4 SMLS SMLS SMLS08-204C-27OS *OFFSET 8 THE GAGE BILT GBP745D TOOL IS APPROVED TO INSTALL THE ABOVE S *ALL OFFSET 204 SERIES NOSES REQUIRE ADAPTER, & ALL OFFSET 205 SERIES NOSES REQUIRE ADAPTER. 1) ALL MATERIALS EXCEPT TITANIUM & STAINLESS. 2) 100 PSI REQUIRED FOR ALLOY STEEL. 3) ALUMINUM ONLY. 4) 100 PSI REQUIRED FOR ALLOY (MS90353 & 4). 5) GENERAL PURPOSE LOCKBOLTS ONLY. 6) INSTALLS 5/32, 3/16 & 1/4 DIAMETERS. 7) INSTALLS 1/8, 5/32, & 3/16 DIAMETERS. 8) ALL OFFSET 752 SERIES NOSES REQUIRE ADAPTER 9) 105 P.S.I. REQUIRED FOR ALLOY STEEL. NOTE: THE LAST 2 DIGITS OF THE REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES GAGE BILT ALSO SUPPLIES PIN & COLLAR SWAGE INSPECTION GAGES TO CERTIFY CORRECT SWAGE INSTALLATION. Rev. 11/08
41 Introducing the GBP745LBK & GBP745LBK-1 GAGE BILT now offers a complete installation kit for 3/16 thru 3/8" C6L & Avdelok commercial lockbolts. The GBP745LBK comes with a set of straight noses to install 6, -8, -10 & -12 diameters, bleeder bottle, adapter, grip scale and pintail catcher bag. The dash one kit also includes adapters and offset noses, must items for re-work operations. All these items are stored in an easy access carrying case with manuals and data sheets. Please view the back of this flyer for pictures of your C6L & Avdelok fasteners and noses to match. 9/07 GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
42 COMMERCIAL LOCKBOLTS C6L & AVDELOK DIA. STRAIGHT NOSE ASSEMBLIES OFFSET 3/16" 1 LB NAS06-204B-25OS 1/4" 1 LB NAS08-205A-31 *5/16" LB10-745C-26 3 NAS10-205A-31 **3/8" LB NAS12-205A REQUIRES ADAPTER REQUIRES ADAPTER REQUIRES ADAPTER *ALL MATERIALS EXCEPT TITANIUM & STAINLESS ** GENERAL PURPOSE LOCKBOLTS ONLY..750 Ø (19.1mm) (49.6mm) 1.06 (26.9mm).48 (12.2mm) (68.6mm) 1.97 (50.1mm) LBXX LB Ø (58.7mm) 2.06 Ø (52.3mm) 5.63 (143mm) 8.58 (217.9mm).810 (20.6mm).330 R. (8.4mm) (66.7mm) (27.0mm) 1.50 Ø (38.1mm) (31.8mm) (53.3mm) 1.84 (46.7mm) 1.50 (38.1mm) 2.25 (57.2mm) Ø (33.3mm) NASXX-204B-25OS (79.4mm) Ø (28.7mm) (34.8mm) 4.78 (121.6mm) (34.9mm) (63.4mm) 4.88 Ø (123.9mm) GBP745D 6.17 (156.7mm) NASXX-205A-31
43 Introducing the GBP745TCK Trailer and Cab Kit Choose GAGE BILTS blind rivet and lockbolt installation kit designed especially for Truck and Trailer OEM s. The GBP745TCK can be configured to meet your needs, whether you re fixing Wabash, Great Dane, Peterbilt, Kenworth or any other brand trailer or truck. The kit includes nose assemblies to pull your fasteners, and at the heart of the system is our heavy-duty GBP745D installation tool. All of this is conveniently stored in a metal tool case. The GBP745TCK kit comes with a nose and 2 tips to install 3/16 and 1/4 structural blind rivets in any material, a bleeder bottle, a catcher bag for pintails, a 3/16 & 1/4 Magna-Grip nose for the hood and cab and a 3/8 C6L Huckbolt nose. An adapter is included for the noses through 1/4. GAGE BILT MADE IN U.S.A. 3/07 Rev. 8/07 GAGE BILT PRODUCTS CORP Centre Court (586) Clinton Twp. MI (586) Fax solutions@gagebilt.com /
GB2581 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB2581 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationGBP784B INSTALLATION TOOL
GBP784B INSTALLATION TOOL GAGE BILT MADE IN U.S.A. GAGE BILT PRODUCTS CORP. 14500 Barber Drive (586) 771-7664 Warren, Mi 48088 (586) 771-2665 Fax e-mail:solutions@gagebilt.com / www.gagebilt.com TABLE
More informationGBP745D/204 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GBP745D/204 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038
More informationGAGE BILT. AEROSPACE Blind Rivet and Lockbolt Installation Tools RIVET TOOLS. Catalogs. Website. Made in the USA
GAGE BILT RIVET TOOLS Made in the USA AEROSPACE Blind Rivet and Lockbolt Installation Tools Catalogs Website Blind Rivet & Lockbolt Tools GB51 Pneumatic 2.5 pounds.740 stroke 1000 lb. (4.45kN) pull force
More informationGB51 GAGE BILT MADE IN U.S.A. PNEUMATIC INSTALLATION TOOL
ORIGINAL INSTRUCTIONS GB51 PNEUMATIC INSTALLATION TOOL PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GAGE BILT MADE IN U.S.A. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR
More informationGB751SH GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB751SH INSTALLATION TOOL GAGE BILT MADE IN U.S.A. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationGB7624 GAGE BILT MADE IN U.S.A. HYDRAULIC INSTALLATION TOOL
GB7624 HYDRAULIC INSTALLATION TOOL PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT
More informationGB2620 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB2620 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationGB204/GB204A GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB204/GB204A INSTALLATION TOOL GAGE BILT MADE IN U.S.A. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038
More informationGB752 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB752 INSTALLATION TOOL GAGE BILT MADE IN U.S.A. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationGB2620 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB2620 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationGB751 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB751 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationGB745 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB745 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationORIGINAL INSTRUCTIONS GB2480/GB2480(A) HYDRAULIC INSTALLATION TOOL
ORIGINAL INSTRUCTIONS GB2480/GB2480(A) HYDRAULIC INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE in USA 44766 Centre Court Clinton Twp. MI
More informationGB752 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB752 INSTALLATION TOOL PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GAGE BILT MADE IN U.S.A. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. 44766
More informationGB910 GAGE BILT MADE IN U.S.A. HYDRAULIC POWERUNIT
GB910 HYDRAULIC POWERUNIT GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationGB745 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB745 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586)
More informationORIGINAL INSTRUCTIONS GB713 INSTALLATION TOOL
ORIGINAL INSTRUCTIONS GB713 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE in USA 44766 Centre Court Clinton Twp. MI 48038 USA Ph: +1 (586)
More informationGP Groove Proportioned Lockbolt Fasteners 13 GPL3SC GPL4SC GPL7TP GPL8TP GPL3SP GPL7TC GPL8TC. MGP Groove Proportioned Lockbolt Fasteners 19
2013 HUCK AEROSPACE INSTALLATION EQUIPMENT OCT 2013 Contents C Introduction 7 1 2 3 4 5 6 7 8 GP Groove Proportioned Lockbolt Fasteners 13 GPL3SC GPL4SC GPL7TP GPL8TP GPL3SP GPL7TC GPL8TC MGP Groove Proportioned
More informationGB703 GAGE BILT MADE IN U.S.A. INSTALLATION TOOL
GB703 INSTALLATION TOOL PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE IN U.S.A. GAGE BILT Inc. 44766
More information(E) WIDE BEARING ENCAPSULATED (M) MEDIUM BEARING ENCAPSULATED CLEARANCE SLEEVE MEDIUM BEARING SLEEVE WIDE BEARING SLEEVE
HUCK INTERACTIVE CD ROM : SPECIFICATION DRAWINGS C C 10.03 10.03 B B F E D F E D (E) WIDE BEARING ENCAPSULATED (M) MEDIUM BEARING ENCAPSULATED J J J K K K WIDE BEARING SLEEVE MEDIUM BEARING SLEEVE CLEARANCE
More informationORIGINAL INSTRUCTIONS G715A. Pneumatic-hydraulic Riveter E. Warner Ave Santa Ana, CA
ORIGINAL INSTRUCTIONS G715A Pneumatic-hydraulic Riveter 1224 E. Warner Ave Santa Ana, CA 92705 www.cherryaerospace.com DESCRIPTION The Cherry G715A Pneumatic-Hydraulic Riveter is designed specifically
More informationORIGINAL INSTRUCTIONS G700
ORIGINAL INSTRUCTIONS G700 HYDRO-SHIFT CHERRYLOCK RIVETER 1224 East Warner Ave, Santa Ana, Ca 92705 Tel: 1-714-545-5511 Fax: 1-714-850-6093 www.cherryaerospace.com G700 HYDRO-SHIFT INSTRUCTIONS TABLE OF
More informationM39075 ( IF- 1) Integra- Fuse Rivet Tool
M39075 ( IF- 1) Integra- Fuse Rivet Tool Marson is making installation easier than ever with the new Marson Integra-Fuse (IF-1) It s the one-and-only tool needed for single-pull installations of open-end
More informationORIGINAL INSTRUCTIONS GB745 INSTALLATION TOOL
ORIGINAL INSTRUCTIONS GB745 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE in USA 44766 Centre Court Clinton Twp. MI 48038 USA Ph: +1 (586)
More informationGAGE BILT INC. GB940 HYDRAULIC POWER UNIT
GAGE BILT INC. 44766 Centre Court, Clinton Township, MI 48038 USA 586-226-1500 fax 586-226-1505 www.gagebilt.com TABLE OF CONTENTS Description Page Safety Instructions... 3 Tool specifications...4 Description...
More informationORIGINAL INSTRUCTIONS GB2628/GB2628A INSTALLATION TOOL
ORIGINAL INSTRUCTIONS GB2628/GB2628A INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT MADE in USA 44766 Centre Court Clinton Twp. MI 48038 USA Ph:
More informationMP-4V Heavy Duty Riveter / 39048
MP-4V Heavy Duty Riveter / 39048 This newly designed heavy-duty air/hydraulic riveter is ergonomically designed with the professional in mind. The lightweight 3.7 lbs. well balanced MP-4V includes a Vacuum
More informationORIGINAL INSTRUCTIONS G85D-S
TM-G85D-S Rev: G, DATE: 4/30/5, DCR# 5-0403 Federal Identification Code: 85 05 Cherry Aerospace ORIGINAL INSTRUCTIONS G85D-S Split Lockbolt Power Riveter 4 E. Warner Ave, Santa Ana, CA 9705 Tel: -74-545-55
More informationG704B. Original Instructions COMPACT CHERRYMAX POWER TOOL
Original Instructions G704B COMPACT CHERRYMAX POWER TOOL 1 1224 E. Warner Ave, Santa Ana, Ca 92705 Tel: 1-714-545-5511 Fax: 1-714-850-6093 www.cherryaerospace.com THE G704B TOOL TABLE OF CONTENTS Description...
More informationAutomotive Air Conditioning Manifold Gauge Sets
Automotive Air Conditioning Manifold Gauge Sets 1 Caution: These instructions are not for use with Hybrid Vehicles. For instructions for servicing Hybrid Vehicles use Hybrid Vehicle manufacturer s service
More informationInstruction Manual Model# RK-187
Instruction Manual Model# RK-187 FOR SALES, SERVICE OR TECH SUPPORT CALL: 1800-BUY-RIVET or 1-800-289-7483 CONTENTS Features Page 3 Safety Page 3 Specifications Page 3 Air supply Page 4 Operation Page
More informationLOCKBOLTS Konnect 8M x 25MM Metric Tape Measure & RIVETS
LOCKBOLTS & RIVETS 116 Sign up today for Konnect s new online store KonnectShop Available 24 hours a day, 7 days a week Buy online at any time via the easy to use Shopping Cart facility Browse & choose
More informationCONTENTS P4 P5-6 P7 P8-9 P10 P11 P12-13 P14-15 P16 P17 SPECIALTY LIFTS BOTTLE JACKS COMPACT SERVICE JACKS HEAVY DUTY SERVICE JACKS JACK STANDS
CONTENTS P4 P5-6 P7 P8-9 BOTTLE JACKS COMPACT SERVICE JACKS HEAVY DUTY SERVICE JACKS SPECIALTY LIFTS P10 P11 P12-13 P14-15 JACK STANDS ENGINE CRANES & STANDS CREEPERS & SEATS SPECIALTY CREEPERS P16 P17
More informationUtility Controller Hand Air Operated
Utility Controller Hand Air Operated P-1395 819-0288 Installation Instructions Introduction The Warner Electric air/manual Utility Controller combines manual and automatic (air) actuation for the operation
More informationSC HYDRAULIC ENGINEERING CORPORATION
Designers and Manufacturers of Hydraulic and Pneumatic Equipment SC HYDRAULIC ENGINEERING CORPORATION 1130 Columbia Street - Brea, California 92821 - USA Phone (714) 257-4800 - Fax (714) 257-4810 10 SERIES
More informationG84. Original Instructions. Lockbolt Power Tool
Original Instructions G84 Lockbolt Power Tool 1224 E. Warner Ave, Santa Ana, Ca 92705 Tel: 1-714-545-5511 Fax: 1-714-850-6093 www.cherryaerospace.com THE G84 TOOL TABLE OF CONTENTS Description...3 Specifications
More informationRIV302-E Heavy Duty Riveter / 39062
RIV302-E Heavy Duty Riveter / 39062 This durable air/hydraulic riveter, with its fully adjustable vacuum system that holds the rivet in the nosepiece, allowing the operator to rivet at any angle with one
More informationHucktainer For Metal-Clad Polymer Core Composite and Fiberglass Reinforced Panel Structures
Hucktainer For Metal-Clad Polymer Core Composite and Fiberglass Reinforced Panel Structures Weather Resistant Installs in Seconds Corrosion Resistant Hucktainer Bringing Huck Quality to Composite Panel
More informationInline & 90 Live Swivels Fax:
Inline & 90 Live Swivels www.superswivels.com 763-784-5531 Email: sales@superswivels.com Fax: 763-784-7423 CW1602 Super Swivels was established in 1986. Our goal is to manufacture heavy-duty, leak free,
More informationSpecial Applications Require Special Tools
Index Routers.................. 102-103 Tappers..................... 104 Clinch Nut Tools.............. 106 Rivet Shavers................ 107 Skin Clamp Runners........... 108 Saws................... 109-110
More informationUSER S OPERATING AND INSTRUCTION MANUAL
Grand Rapids, Michigan, U.S.A. 49504-5298 USER S OPERATING AND INSTRUCTION MANUAL MODEL 777 SLICER 0777S20000-CVR THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319 THIS PAGE WAS INTENTIONALLY LEFT BLANK.
More informationCHERRYLOCK BLIND RIVET
CHERRYLOCK BLIND RIVET SPS Fastener Division, a PCC Company 1 1 CHERRYLOCK RIVET LIMITED WARRANTY Seller warrants the goods conform to applicable specifications and drawings and will be manufactured and
More informationAIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER
AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER AIR DRILL KW0800256 3/8 Chuck, Reverse Equipped with precision chucks for excellent accuracy Precision bearing provides longer tool durability KW0800258
More informationSIOUX TOOLS, INC. POWER TOOLS WARRANTY
E A SELZER AEROSPACE AEROSPACE SIOUX TOOLS, INC. POWER TOOLS WARRANTY SIOUX TOOLS, INC. WARRANTS TO THE ORIGINAL PURCHASER THAT THE COMPANY S POWER TOOLS ARE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP.
More informationUSER S OPERATING AND INSTRUCTION MANUAL
Grand Rapids, Michigan, U.S.A. 49504-5298 USER S OPERATING AND INSTRUCTION MANUAL MODEL 797-21 BREAD SLICER 797S20000CV_21 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319 RECOMMENDED
More informationMINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM
MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM Muncie Power Products OPTIMUM Series gear pumps/motors offer premier performance for a wide variety of applications across several industries.
More informationInstruction Manual Model# RK-8000S
Instruction Manual Model# RK-8000S FOR SALES, SERVICE OR TECH SUPPORT CALL: 1800-BUY-RIVET or 1-800-289-7483 CONTENTS Features Page 3 Safety Page 3 Specifications Page 3 Air supply Page 4 Operation Page
More informationPCC O P E R A T I O N S. Pump Cycle Counter M A N U A L. Environmental Systems
O P E R A T I O N S Environmental Systems PCC Pump Cycle Counter M A N U A L PO Box 3726 Ann Arbor, Michigan 48106-3726 (800) 624-2026 North America Only (734) 995-2547 Tele. (734) 995-1170 Fax info@qedenv.com
More informationSIOUX TOOLS SIGNATURE SERIES PRODUCT BROCHURE SPECIALTY CLINCH NUT
SIOUX TOOLS SIGNATURE SERIES PRODUCT BROCHURE SPECIALTY CLINCH NUT S E R I E S SPECIALTY SIOUX TOOLS SIGNATURE SERIES PRODUCT BROCHURE Tool Selection / Order Guide Selecting the proper tool for your clinch
More informationEBBERT RIVETING SOLUTIONS SALES & ENGINEERING GUIDE
EBBERT RIVETING SOLUTIONS SALES & ENGINEERING GUIDE 06-05-015 HK1060 CONTENTS CONTENTS... TOOLS ERT1S... & 4 ERTS...5 & 6 ERTS...7 & 8 ERT4S...9 & 10 ERT5S...11 & 1 ERT6S...1 & 14 ERTSMQ...15 & 16 ERT9
More information76" H x 36" W x 27" D. 80" H x 38" W x 48" D. Maximum 150 psi Standard shop air (8 100 psi)
Part# 26BPAC - Pack-Master Air Compactor The Pack-Master Air is the best value for a pneumatic waste compactor. With the Pack-Master Air, you can effortlessly compact material in a 30 or 55 gallon drum
More informationNor East. Instructions Safety Messages. Inspection. Parts. DeZURIK Service. Type 05 Pneumatic Actuator Used With Globe Valves
Instructions Safety Messages These instructions are intended for personnel who are responsible for installation, operation and maintenance of your DeZURIK Actuator. All safety messages in the instructions
More informationQuick Start Manual FLEX-5P. Threaded Insert Power Tool Pull to Pressure Set Up
Quick Start Manual FLE-5P Threaded Insert Power Tool Pull to Pressure Set Up Part of the FLE family of modular-based tooling. FLE tooling has the capability to be upgraded from the original base tool.
More informationFPC835M Air Hydraulic Rivet Tool
WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at -800-860-3838 before returning it to the place of purchase. FPC835M Air Hydraulic Rivet Tool FPC Corporation warrants
More informationHUCK-CLINCH / HUCKMAX
BLIND RIVETERS 85 HUCK-CLINCH / HUCKMAX NAS Cherrymax Military Boeing Zenith AERO House INDUSTRIAL Aqueduct TOOL Street CO., Inc. Preston Lancashire Fax 941.379.5449 PR1 7TB Huckmax NAS9301B CR3213 M7885/2
More informationQuick Start Manual FLEX 5S. Threaded Insert Power Tool Pull to Stroke Set Up
Quick Start Manual FLEX 5S Threaded Insert Power Tool Pull to Stroke Set Up Part of the FLEX family of modular based tooling. FLEX tooling has the capability to be upgraded from the original base tool.
More informationTool & Product Update
Tool & Product Update NOSE ASSEMBLY TO TOOL ADAPTER MATRIX AND DRAWINGS On the following page is a list of every currently available Adapter Assembly combination. Please use the list as a reference when
More informationSIOUX TOOLS SIGNATURE SERIES PRODUCT BROCHURE SPECIALTY CLINCH NUT
SIOUX TOOLS SIGNATURE SERIES PRODUCT BROCHURE SPECIALTY CLINCH NUT S E R I E S SPECIALTY SIOUX TOOLS SIGNATURE SERIES PRODUCT BROCHURE Tool Selection / Order Guide Selecting the proper tool for your clinch
More informationFPC815 Pneumatic Rivet Tool
WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. FPC815 Pneumatic Rivet Tool FPC Corporation warrants
More informationModels & Options Lubrication. 1/2 Through 10 Hp Models 1Ø 3Ø 1/2 Through 10 Hp Models 1Ø and 3Ø
P U R E A I R T E C H N O L O G Y Climate Control Duplex Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect
More informationHi*Lite XL Suspension Insulators
27 Hi*Lite XL Suspension Insulators Table of Contents Page Design... 2 Rod... 2 End s... 2 Weathersheds... 2 Interface... 2 Leakage... 2 Washability... 2... 2 Lengths Available... 2 Product Updates...
More informationInstallation & Operation Manual. Electrak 100 Series / Electromechanical Linear Actuator
www..c Installation & Operation Manual Electrak 100 Series / Electromechanical Linear Actuator Thomson has many years of experience designing and manufacturing linear actuators for a wide variety of applications
More informationOWNERS MANUAL INSTALLATION AND OPERATING INSTRUCTIONS REPAIR PARTS LIST. Centrifugal Pump Primer MODEL 6D, HAN-DEE PRIMER
OWNERS MANUAL INSTALLATION AND OPERATING INSTRUCTIONS REPAIR PARTS LIST Centrifugal Pump Primer 383 0893 MODEL 6D, HAN-DEE PRIMER IMPORTANT For best possible performance continuous, satisfactory operation,
More informationDual Phase Extraction Inlet. Patent No Installation Manual. P/N Rev
Patent No. 6520259 Installation Manual P/N 95232 Rev 6-16-11 Table of Contents ing Extraction Inlets track changing water levels to maintain optimum performance 1.Component Identification Page 1 2. How
More informationPotentiometer Thrust Plate Kit (50421) Installation & Operator s Instruction Manual
Potentiometer Thrust Plate Kit (0) Installation & Operator s Instruction Manual Thank You The employees of Chore-Time Equipment would like to thank you for your recent Chore-Time purchase. If a problem
More informationElectromagnetic Particle Brakes Model: PRB-H
P-223-3 819-0370 Electromagnetic Particle Brakes Model: PRB-H Installation Instructions Table of Contents Introduction............................2 Installation Instructions....................3 Start
More informationSC HYDRAULIC ENGINEERING CORPORATION
Designers and Manufacturers of Hydraulic and neumatic Equipment SC HYDRAULIC ENGINEERING CORORATION 113 Columbia Street - Brea, California 92821 - USA hone (714) 257-48 - Fax (714) 257-481 B AB/ABD AIR
More informationECONOMAIR SERIES CYLINDERS
OPERATOR S MANUAL INCLUDING: APPLICATION, LUBRICATION, INSTALLATION & SERVICE ECONOMAIR SERIES CYLINDERS 2XXX-XXX9-XXX RELEASED: 9-14-92 REVISED: 3-6-01 (REV. B) READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
More informationCompressor Clutch Replacement Procedure
P-1411 819-0361 Compressor Clutch Replacement Procedure Installation Instructions World Clutch with Unidamp Armature for Ford FX-15 and FS-10 Compressors and all Denso Models with 30mm bearing fit. Keep
More informationWarner Electric UNIBRAKE Motor Brakes
P-1699-WE Warner Electric UNIBRAKE Motor Brakes Installation & Operating Instructions Double C Contents General Information........................ 2 Brake Heads............................. 2 Installation...............................
More information14", 18" & 24" Fiberglass Turbo Fans Installation & Operator s Instruction Manual
14", 18" & 24" Fiberglass Turbo Fans Installation & Operator s Instruction Manual 09484:09#52
More information12 Volt Utility Controller for 4, 6 or 8 Brakes No P
12 Volt Utility Controller for 4, 6 or 8 Brakes No. 1300-77 P-1379 819-0094 Installation Instructions Introduction The Warner Electric manually operated Utility Controller operates 4, 6, or 8 twelve-volt
More informationMODEL 660 AUTOMATIC FASTENING CENTER OPERATOR S MANUAL
MODEL 660 AUTOMATIC FASTENING CENTER OPERATOR S MANUAL Copyright: January 13, 2003 Revised: 080612 Serial No. 0506113. 1 TABLE OF CONTENTS INTRODUCTION..3 OPERATOR SAFETY... 3 SYSTEM REQUIREMENTS..4 INSTALLATION
More informationHPI Cylinders. Manufacturers of Hydraulic & Air Cylinders Since 1946
HPI Cylinders Manufacturers of Hydraulic & Air Cylinders Since 1946 Cylinder Catalog 2018 HPI Cylinders www.hpicylinders.com Since 1946 Main Plant 13766 Milroy Place Santa Fe Springs, CA 90670 Phone (800)
More informationHERBIE CLIP & EZYCLIK PNEUMATIC PISTON & CALLIPER TOOLS. Operation, Parts & Safety Manual Original Instructions
HERBIE CLIP & EZYCLIK PNEUMATIC PISTON & CALLIPER TOOLS Operation, Parts & Safety Manual Original Instructions M A R C H 0 INDEX Tooling Depending on set up, the selected tool is designed to assemble
More informationMarson Rivets and Rivet Nut Installation Tools
Marson Rivets and Rivet Nut Installation Tools Marson Manual Rivet Tools HP-2 Professional Hand Rivet Tool (M39000)* The HP-2 is the number one selling hand rivet tool in the industry. Known and trusted
More informationSC HYDRAULIC ENGINEERING CORPORATION
Designers and Manufacturers of Hydraulic and Pneumatic Equipment Since 193 SC HYDRAULIC ENGINEERING CORPORATION 113 Columbia Street - Brea, California 981 - USA Phone (71) 7-8 - Fax (71) 7-81 P 1 SERIES
More informationAMERICAN AVK COMPANY TABLE OF CONTENTS
AMERICAN AVK COMPANY AVK SERIES 815 BUTTERFLY VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR UL/FM APPROVED IPS - GROOVED END BUTTERFLY VALVES 2½" - 8" TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST
More informationOWNERS MANUAL JANUARY 2007 ISO
Manufacturer of Dimensions TM Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000 Fax: 651-653-7600 E-mail: inverterinfo@sensata.com Web: www.dimensions.sensata.com OWNERS MANUAL JANUARY
More informationFeatures and Specifications for Impact Wrenches
Pneumatic Air Tools Version 2017 Revised 06/2017 Email your order to: sales@polyconn.com or fax to (763) 398-2590. www.polyconn.com. Questions call: (763)559-0388 3062 Ranchview Lane North. Plymouth, MN
More informationTECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER TECHNICAL ASSISTANCE FAX:
ACORN SAFETY P.O. BOX 57 CITY OF INDUSTRY, CA 97-057 UNITED STATES OF AMERICA WWW.ACORNSAFETY.COM INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS COMBINATION STATIONS, RECESSED ACTIVATION Models:
More informationDesigners and Manufacturers of Hydraulic and Pneumatic Equipment Since 1953 SC HYDRAULIC ENGINEERING CORPORATION
Designers and Manufacturers of Hydraulic and Pneumatic Equipment Since 193 SC HYDRAULIC ENGINEERING CORPORATION 113 Columbia Street - Brea, California 91 - USA Phone (71) 7- - Fax (71) 7-1 P D & 1 SERIES
More informationINSTALLATION/OWNER'S MANUAL DP " Woofer in Enclosure
INSTALLATION/OWNER'S MANUAL DP1000 10" Woofer in Enclosure Installation Thank you for purchasing the DP1000 10" Woofer with enclosure. Although Dual has attempted to make sure all of the information contained
More informationUser Instruction Manual ZT-1017-VS ZT-6000-VS
User Instruction Manual ZT-1017-VS ZT-6000-VS FOR SALES, SERVICE OR TECH SUPPORT CALL: 1800-BUY-RIVET or 1-800-289-7483 CONTENTS Safety Page 3 Specifications Page 3 Preparing the tool for service Page
More informationAIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER
AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER AIR DRILL KW0800256 3/8 Chuck, Reverse Equipped with precision chucks for excellent accuracy Precision bearing provides longer tool durability KW0800258
More informationTECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER TECHNICAL ASSISTANCE FAX:
ACORN SAFETY P.O. BOX 3527 CITY OF INDUSTRY, CA 91744-0527 UNITED STATES OF AMERICA WWW.ACORNSAFETY.COM INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS PEDESTAL EYE/FACEWASH Models S0310 / S0320 /
More informationAir Hydraulic Rivet Tool
WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. FPC845M Air Hydraulic Rivet Tool FPC Corporation
More informationFig Series. Installation and Spare Parts Manual Pilot House Control Solar-Ray Sealed Beam 7 & 8 Searchlights
Fig. 0314 Series Installation and Spare Parts Manual Pilot House Control Solar-Ray Sealed Beam 7 & 8 Searchlights 16490 N.W. 13th Avenue Miami, FL 33169-5707 www.perko.com 0314PTD5 Rev: 9/2016 Fig. 0314
More informationTECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER TECHNICAL ASSISTANCE FAX:
ACORN SAFETY P.O. BOX 3527 CITY OF INDUSTRY, CA 91744-0527 UNITED STATES OF AMERICA WWW.ACORNSAFETY.COM INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS COMBINATION STATIONS Models: S1310, S1320, S1330,
More informationTECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER TECHNICAL ASSISTANCE FAX:
ACORN SAFETY P.O. BOX 3527 CITY OF INDUSTRY, CA 91744-0527 UNITED STATES OF AMERICA WWW.ACORNSAFETY.COM INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS DECK MOUNTED EYE/FACEWASH Model S0730 / S0740
More informationTPCA Power Clamps Catalog
TPCA Power Clamps Catalog Pneumatically Operated, Weld-Contamination Sealed, Heavy Duty Power Clamps > Degree of arm opening can be adjusted from -12 > One clamp for both dual or single arms > Uses TRILOK
More informationOPERATION MANUAL Variable Speed Pump Controller Dated: 06/04/2013 Pump Down Application. Document No.: LMSII_V100_OM Page 1 of 8 Model-V100 LMS II
Document No.: LMSII_V100_OM Page 1 of 8 LMS II Document No.: LMSII_V100_OM Page 2 of 8 1. Operation: When the wet well level rises above the on level set point, the lead pump will start after an adjustable
More informationDimensions 12/800N 12/1200N D. DC to AC Power Inverters. OWNERS MANUAL for Models: OWNERS MANUAL April ISO 9001:2000 Certified Company
Manufacturer of Dimensions Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000 Fax: 651-653-7600 E-mail: inverterinfo@sensata.com Web: www.dimensions.sensata.com OWNERS MANUAL April
More information12-1/4 x 3-1/2 Electric Wheel Brake
12-1/4 x 3-1/2 Electric Wheel Brake A-216 819-0244 Installation Instructions An Altra Industrial Motion Company Contents Dimensions.... 2 Technical Specifications.... 3 Installation Instructions General....
More informationTerms and Conditions
Terms and Conditions GUARANTEE: All Brighton-Best International, Inc. products are manufactured to rigid quality control standards which meet or exceed industry standards. Records and tests pertaining
More informationOperating and Maintenance Instructions
1500 Tube Leak Test Gun - Vacuum Tube & Pipe Cleaners Tube Testers Tube Plugs Tube Removal Tube Installation Operating and Maintenance Instructions www.elliott-tool.com Table Of Contents Introduction...
More informationModel MC-30D Impact Press. Operation & Maintenance Instructions
Model MC-30D Impact Press Operation & Maintenance Instructions Revised 12/05/2007 1 WARNINGS 1. Safety glasses must always be worn by the machine operator, as well as any co-workers, or any other persons
More informationTooling. Catalogue. Get last version on.
Tooling Catalogue Get last version on http://www.afsrhuck.net/en/products/tooling.html Go on the web page: http://www.afsrhuck.net/en/products/tooling.html Click on the «Aerospace Tooling Catalog» button
More informationAXS609 AXS612 AXS514 AXS SERIES. INSTALLATION/OWNER'S MANUAL Car Audio
AXS609 AXS612 AXS514 AXS SERIES INSTALLATION/OWNER'S MANUAL Car Audio PREPARATION Safety Guidelines Thank you for purchasing the AXS Series car speakers. Although Axxera has attempted to make sure all
More information