Parts/Hardware Included. Caution. Tools/Hardware Required. SMS CL V Mounting Plate. SMS CL V Exploded View

Transcription

1

2 Caution ➀ Installer must make sure SMS CL V is positively and securely attached, and appropriate fasteners are used. ➁ Before installing, check to make sure all parts of the mount are there. ➂ Assembly hardware is included; mounting fi ttings are not included with the product for reasons of safety, since the properties and bearing strength of walls/ceilings are specifi c for each case. Suitable mounting fittings must be selected based on the material of the wall/ceiling. It is the responsibility of the installer to ensure that the wall/ceiling can support at least four times the combined weight of the screen/projector and bracket. ➃ The maximum weight of a screen/projector to be used with the SMS CL V is 12 kg, or 26 lb. ➄ Make sure all screws and bolts are tightened before allowing the mount to bear the full weight of the projector. ➅ Mount projector before hooking up to electrical and other cables. ➆ When making adjustments, make sure projector is fi rmly supported. ➇ All assembly screws require Metric Allen wrench (included). Tools/Hardware Required Parts/Hardware Included SMS CL V Mounting Plate SMS CL V Exploded View

3 ➀ Pre-assemble upper column (A) to celiing plate (B) using provided hardware. ➁ Use ceiling plate to mark mounting hole positions on ceiling. ➂ Drill mounting holes. ➃ Attach ceiling plate and upper column to ceiling. Please Note: mounting fittings are not included with the product for reasons of safety, since the properties and bearing strength of walls/ceilings are specific for each case. Suitable mounting fittings must be selected based on the material of the wall/ceiling. It is the responsibility of the installer to ensure that the wall/ceiling can support at least four times the combined weight of the screen/projector and bracket.

4 ➂ On adjustable models, if appropriate, run wiring down through large slots in mounting plate. ➃ Run wiring along cable guides for hookup to projector. Place cable covers in cable guides, then snap on side covers. ➄ Attach lower column cover. Adjustment Some models of the CL V have several points of adjustment. For ranges of adjustment according to model, see charts below. Adjustments are infinite within range. Adjustments can be made with the projector attached to the mount; built-in safety features will prevent accidents by catching the lower section before it drops out of the unit.

5 CL F 80 Fixed Mount Dimensions Adjustable Mount Dimensions Distance between ceiling and bottom of mount: 3 1 /8" 2 3 /4" Distance between ceiling and bottom of Universal Projector: Bracket: 6" 3 7 /8" 4 3/4" 7 1/2" 11/2" 2 3/8" Low Profile 33/8" 3/16" A B 4 7 /8" Max. approx. O 15" (380 mm) Universal Projector Bracket Coverage C Min. approx. O 51/2" (140 mm) A minimum of three mounting holes need to be used to securely attach the Aero Universal Bracket to the projector. Attaching Universal Mounting Bracket to Projector ➀ Place the Universal Projector Mounting Bracket over projector mounting holes. If bracket arms cannot reach all mounting holes, loosen bracket by unscrewing centerpiece, and replacing bracket arms with longer size arms (included). Please Note: Open ends of bracket arms should be at least flush with the outer edge of the centerpiece; if open ends are not fl ush, use longer arms. Model A (Min) B (Max) C CLV /8" 15 3 /8" 2" CLV /4" 31 1 /8" 9 7 /8" CLV /4" 37" 9 7 /8" CLV /8" 44 7 /8" 9 7 /8" CLV " 52 7 /8" 9 7 /8" Adjustability Pitch Roll Yaw At Ceiling Plate ±30º 0º 0º At Ball Joint ±30º ±30º 360º Please Note: Universal Bracket adds a minimum of 3" to overall height. ➁ Insert and adjust threaded pipe so that, when they are flush with the surface of the projector, the universal bracket is horizontally level.

6 ➂ Insert and tighten screws (provided) appropriate for projector mounting holes. Please Note: Do not overtighten screws into projector. If screw is hitting the end of the threaded hole, add more washers at the top of the screw. ➃ Adjust the centerpiece so that it is above the projector s center of gravity, and tighten centerpiece. To determine the projector's center of gravity, place a small level on the projector. Hold the projector by the top of the bracket nut and make sure the projector hangs level. Adjust the Universal Projector Bracket by sliding the centerpiece along the arms until the projector hangs level, then tighten the centerpiece. ➄ Tighten lower locking nut. ➅ Place the mount ball joint into the slot in the nut. ➆ Tighten the nut. ➇ Tighten the upper locking nut. ➈ Rotate projector into position. ➉ Adjust height and tighten setscrews.