INSTALLATION & OWNER S MANUAL
|
|
- Chrystal Blankenship
- 5 years ago
- Views:
Transcription
1 INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 CAB KIT (p/n: KAF40-005WA and KAF40-005BA) NOTE: Hard sided doors are sold separately. This manual is the property of the owner. Be sure to leave with the owner when installation is complete. Rev. F p. 1 of 7 p/n: IM-KAF40-005
2 ADDED WEIGHT Curtis Cabs, blades and general accessories add additional weight to the base vehicle. All Curtis accessory weights are listed in product brochures. Deduct the accessory's total weight from the vehicle's rated capacity and never exceed the vehicle's rated capacity including driver and passenger. Exposure to Carbon Monoxide can Cause illness, serious injury or death. Never operate vehicle if suspicious of Carbon Monoxide. Inspect exhaust system for leaks monthly. Leaks can result from loose connections, corrosion, cracks or other damage to the exhaust manifold. If leaks are found, repair or replace exhaust system. Do not use vehicle until repair or replacement is complete. CAB INSTALLATION BEFORE YOU START HELPFUL HINTS: A. Refer to parts diagram toward the back of this manual to help identify parts during the assembly process. B. To assist with the cab installation, leave all bolts loose for later adjustment unless otherwise specified. C. Read and understand all instructions before beginning. D. Plastic washers have been supplied to provide a weather seal under the heads of all exterior bolts. The plastic washer should be installed under each bolt head directly against the outside cab surface. Care should be taken not to over tighten the fasteners and damage the plastic washer. Also use steel washers as required. See diagram. E. Apply a clear silicone sealant to seal any minor gaps that may occur due to vehicle variations. F. Use caution to avoid damaging the factory installed threaded inserts. Begin the bolt engagement by hand to guard against potential cross threading. TOOLS REQUIRED: Set of standard and metric sockets Set of standard and metric open end wrenches Drill 3/8" drill bit. Bar Clamp One Phillips Head Screwdriver One 3/8 Drive Ratchet One 3/16 Allen Wrench Utility Knife Tape Measure p. 2 of 7
3 VEHICLE PREP: NOTE: HEAVY DUTY FRONT SUSPENSION SPRINGS (p/n: ) ARE REQUIRED WHEN INSTALLING THIS CAB. INFLATE FRONT TIRES TO 1.0 kg/cm2 or 14.2 PSI AND MAINTAIN AT THIS PRESSURE. A. On model years with retractable seat belts, flip the passenger s side seat belt so that it no longer protrudes outboard of the ROPS. That will give clearance away from the cab frame once it s installed. Fig. A1 shows the original orientation and Fig. A2 shows it flipped for clearance. Tighten the bolt back to the original OEM torque of 33 ft.-lbs. (or 44.5 N-m). B. Per fig. B, remove bolts from between front and rear ROPS. Remove nuts and bolts from top of rear screen. Save all hardware for later use. C. Per fig. C, loosen all nuts attaching seat back to vehicle. Remove the two upper nuts but leave the bottom nuts attached. STEP 1 REAR PANEL A. Per fig. 1, install 4 pieces of weather seal on the inside of the two middle uprights on the rear screen. B. With the bulb rubber facing forward, install the rear panel in front of the rear screen by pushing down over the seat back mounts. STEP 2 REAR MOUNT A. Per fig. 2, install the rear mount by placing it between the front and rear cab bars and reinstalling the bars removed in Vehicle Prep step B. NOTE: Do not tighten bolts. STEP 3 SIDE FRAME INSTALLATION A. Remove the protective film from the side frame windows before installing to the vehicle. B. Per fig. 3, install supplied pieces of Expand-a-foam to front cowl as shown. NOTE: Adhesive seal should be applied to a clean, dry surface at room temperature for best adhesion. Fig. A1 Fig. A2 Fig. B Fig. C Fig. 1 Fig. 2 Fig. 3 p. 3 of 7
4 STEP 3 SIDE FRAME INSTALLATION (continued) C. (Figure 6) With assistance, install the left and right side frames by inserting the upper rear corner behind the rear mount installed in Step 2. Pivot the front of the frame down onto the front fenders. Place side frame floorboards on to the vehicle floor. Attach side frames to rear mount with 5/16" x 3/4" carriage bolts (one per side). D. (Figure 7) Install the front mounts to the left and right side frames with 5/16" x 3/4" bolts, and washers, provided. STEP 4 FUEL FILLER INSTALLATION A. (Figure 8) Tip the front seat bottom forward, remove the cap from the fuel tank, and install the fuel filler to the right side frame with four machine screws provided. Install fuel filler gasket by pressing over neck of fuel tank. Re-install fuel tank cap. STEP 5: WINDSHIELD & WINDSHIELD SUPPORT A. (Figure 9) Bolt the windshield support to the left and right side frames with 5/16 x 3/4 carriage bolts in the lower holes only (1 per side). Install with six slots at top of support. Align outer edges of windshield support with edges of side frames and tighten carriage bolts. B. (Figure 10). With assistance, lift the windshield onto the front of the side frames and bolt hinges to windshield support with hinge spacers, 5/16 X 1-3/4 flat head bolts, washers, and locknuts. Align sides of windshield with side frames and while holding in position close latches against the back side of the windshield strikers. NOTE: If the windshield does not seal to the side frames near the bottom, it is hitting the hood too hard, undo the latches and adjust the windshield up. If it does not seal against the hood, adjust the windshield down. Tighten bolts to 7 ft-lbs. CAUTION: Do not over torque fasteners through plastic hinges. C. (Figure 11 next page) Install the supplied gas springs to the windshield and side frames with the piston pointing down. Push gas spring ends over ball studs and snap covers into place to secure. Figure 6 Figure 7 Figure 8 Figure 10 Figure 9 p. 4 of 7
5 STEP 6: ROOF A. Use a Phillips head screwdriver to punch a hole through the headliner at all of the covered bolt hole locations (8 places). Punch holes from the inside out to avoid having the headliner pull away from its glued surface. B. (Figure 12) With assistance, install the roof. Use 5/16-18 x 1 long carriage bolts in the front corners, use 3/4" long carriage bolts in the remaining six holes. STEP 7 POSITION AND TIGHTEN CAB A. Check that the rear mount is centered left to right and tighten the bolts on the R.O.P.S. installed in step 2. B. (Figure 13) Check that the carriage bolt in the top rear of the left side frame is centered (left to right) on the slot in the rear mount and tighten the bolt. Repeat for right side. Figure 11 C. Tighten the front mount. D. Tighten all remaining cab hardware, aligning parts as you go. Install the supplied nut covers. E. (Figure 14) Align edge of side frame floorboard with edge of plastic trim on vehicle floor. Use bar clamp if necessary. Drill 3/8" holes through vehicle floor using the slotted holes in the side frame as a guide. Attach w/ 3/4" long carriage bolts with washers and locknuts under the vehicle. Figure 12 Figure 13 Figure 14 p. 5 of 7
6 STEP 8 REAR CAB FILLERS A. (Figure 15 and 16) Install left and right fillers by snapping into place and applying adhesive backed Velcro as necessary. NOTE: Adhesive backed Velcro should be applied to a clean, dry surface at room temperature. STEP 9 FINISHING TOUCHES A. Install hardware to rear screen and seat back removed in Vehicle prep. Tighten all hardware. Figure 15 B. (Figure 17) Install rubber seals to edges of hood as shown. CARE AND MAINTENANCE A. Check and tighten hardware after 40 hours of operations. Periodically inspect and tighten hardware for the remainder of the unit s life. B. Wash the painted surfaces of the unit with commercial automotive cleaning products. C. Clean windows with glass cleaner. D. Vinyl components should be washed with a mild solution of warm soapy water. Figure 16 (filler shown in yellow for clarity) Clear vinyl can be easily scratched. Be careful cleaning frost or snow from windows. Do not roll curtains in cold weather. The windows become stiff and may crack. Keep curtain clean. Figure 17 p. 6 of 7
7 KAWASAKI MULE 4000 CAB PARTS LIST p/n KAF40-005BA (BLACK) & KAF40-005WA (WHITE) * HEADLINER OFF WHITE OR WINDSHIELD SUPPORT * 1/2" WEATHER SEAL (INSIDE) (9PR20) ROOF * 1 KA TRIM-LOK (3 SIDES) *REFLECTORS 1 KAM4T4-03 * HEYCO PLUGS * RELEASE LATCHES & SPACERS WINDSHIELD REAR PANEL *HINGES W/ NYLON SPACERS SEAM BULB 1 KAM4T4-02 * (2) HEYCO PLUGS * SEAM BULB GAS SPRING MOUNTS (BOTH POINT ) 3/4" SIDE BULB W/ 1/4" GRIP (9PR38) 1 KA * 7/16" SIDE BULB 1/4" GRIP * SERIAL # DECAL, OPTIONS DECAL, AND W/S WARNING DECAL (INSIDE) *1/2" WEATHER SEAL (INSIDE) REAR MOUNT (9PR20) 1 KA UNITIZED SIDE FRAMES 1 KAF L 1 KAF R UPPER MOUNTS RUBBER COATED 2 KAFT4-04 * BALL STUD * LATCH PIN * SNAPS 3 PER SIDE (INSIDE) * HINGE SLEEVES (HS-P1) * 3/8" HEYCO PLUGS. 2 THIS SIDE ONLY REAR FILLERS 1 KA L 1 KA R (RUBBER) * 5/8" OFFSET SIDE BULB FUEL FILLER 1 KAM4T4-13 * 1/2" WEATHER SEAL (INSIDE) 4 SIDES (9PR20) TRIM LOCK 1/4" x 3/4" EXPAND-A-FOAM 5/8" OFFSET SIDE BULB 1/2" WEATHER SEAL 3/4" SIDE BULB W/ 1/4" GRIP 7/16" SIDE BULB W/ 1/4" GRIP 9PRO1 9PR30 9PR27 9PR20 9PR38 ADDITIONAL SERVICE PARTS QTY/CAB p/n DESCRIPTION 1 9GL-34x56 MOLDED WINDSHIELD ASSEMBLY 2 9PH007 & 9BLK01 POP OUT WINDSHIELD HINGE KIT-SINGLE 1 9WL02L POP OUT WINDSHIELD RELEASE LATCH KIT-LH 1 9WL02R POP OUT WINDSHIELD RELEASE LATCH KIT-RH 2 9WL02E POP OUT WINDSHIELD LATCH EXTENSIONS 4 HS-P1 UNITIZED FRAME HINGE SLEEVES 1 KAT4-10 FUEL FILLER GASKET 1 KAT4HWK-01 HARDWARE FASTENER KIT 2 2 9GS09 PG-4000SF WINDSHIELD GAS SHOCKS FRONT SIDE WINDOWS 9PR29 p. 7 of 7
INSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 TRANS 4 FRONT CAB KIT (p/n: KAF40T-001WA and p/n: KAF40T-001BA) NOTE: Hard sided doors, soft sided doors, and rear cab are sold
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. of 0 INSTALLATION & OWNER S MANUAL MASSEY FERGUSON GC2400 cab kit p/n MFGC2400 Installation Instructions The contents of this envelope are the property of the owner. Be sure to leave with the
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 30 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KU3AS) SOFT SIDED CAB ENCLOSURE (p/n 1KU3SS) This Curtis Cab is designed and manufactured
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR MASSEY FERGUSON 233, 428v (gear), 428v (hydro) SOFT SIDED CAB ENCLOSURE (p/n: MF233SS) This Curtis Cab is designed and manufactured for use
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE GATOR HPX and/or XUV HARD SIDED CAB ENCLOSURE (p/n: 1GTR44AS) SOFT SIDED CAB ENCLOSURE (p/n: 1GTR44SS) 111 HIGGINS STREET, WORCESTER,
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. of 2 INSTALLATION & OWNER S MANUAL KUBOTA B2650/3350 Hard Sided Cab p/n KB33AS Soft Sided Cab p/n KB33SS Installation Instructions The contents of this envelope are the property of the owner.
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON THX FOR MASSEY FERGUSON 528, 53, AGCO ST28A, ST33A, CHALLENGER MT255B SOFT SIDED CAB ENCLOSURE (p/n MFTHXSS) This Curtis Cab
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL This Curtis Cab is designed and manufactured for use only as reasonable weather protection. This cab is not applicable, Nor should the cab be considered as protection against
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR E-Z-GO MPT BALL CAGE (p/n 72685-G01) The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON TGX SERIES SOFT SIDED CAB ENCLOSURE (p/n MFTGXSS) This Curtis Cab is designed and manufactured for use only as reasonable weather
More informationINSTALLATION & OWNER S MANUAL
Rev. D, p. 1 of 14 INSTALLATION & OWNER S MANUAL Bobcat CT 230 and KIOTI CK30 cab kit with hard doors and soft rear curtain p/n 1BCT230 & 1KTCK30 The contents of this envelope are the property of the owner.
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. 1 of 6 INSTALLATION & OWNER S MANUAL YANMAR SA-424 WINDSHIELD KIT P/N 1CYSA4WS FITS SA-424 TRACTORS WITH 4 POST ROPS The contents of this envelope are the property of the owner. Be sure to leave
More informationINSTALLATION & OWNER S MANUAL
Rev. G, p. 1 of 19 INSTALLATION & OWNER S MANUAL YANMAR Sc SERIES cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC1AS Yanmar p/n: 59A40056727 Optional Hard Rear Panel Curtis p/n: SC100-06A
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 15 INSTALLATION & OWNER S MANUAL YANMAR Sc2450 cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC2450AS The contents of this envelope are the property of the owner. Be sure to leave
More informationINSTALLATION & OWNER S MANUAL
Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More informationINSTALLATION & OWNER S MANUAL
Rev. L, p. 1 of 18 INSTALLATION & OWNER S MANUAL KUBOTA L3200, L3800, and L2501 WorkPro Hard Sided Cab (p/n: 1KL38AS) WorkPro Soft Sided Cab (p/n: 1KL38SS) An optional Hard Rear Panel can be purchased
More informationINSTALLATION & OWNER S MANUAL
Rev. L p. 1 of 16 INSTALLATION & OWNER S MANUAL V4262 CAMO (SOFT SIDED) CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) & (3120/3320/3520/3720) HARD SIDED CAB ENCLOSURE (p/n 1JD3520AS) SOFT SIDED CAB ENCLOSURE
More informationKUBOTA BX-1500/1800/2200 HARD SIDED CAB (p/n 1KBXAS) SOFT SIDED CAB (p/n 1KBXSS)
TRACTOR CAB INC. 111 HIGGINS STREET, WORCESTER, MA 01606 KUBOTA BX-1500/1800/2200 HARD SIDED CAB (p/n 1KBXAS) SOFT SIDED CAB (p/n 1KBXSS) INSTALLATION AND OWNER S MANUAL The contents of this envelope are
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 15 INSTALLATION & OWNER S MANUAL Polaris Ranger 500-800 PathPro SS Cab (fits 2010 - current) (p/n: 1POLRFS1) The contents of this envelope are the property of the owner. Be sure to leave with the
More informationINSTALLATION & OWNER S MANUAL
1 of 22 INSTALLATION & OWNER S MANUAL Kawasaki Mule PRO-FXT p/n s: 1KAPFXTCA & 1KAPFXTCAS1 fits all Mule Pro 6-Passenger Models Cab Shown with Optional Front Wiper, Lights, and Side View Mirrors Available
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger 400-EV PathPro SS Cab (fits 2010 - current) (p/n: 1PRG400FS) The contents of this envelope are the property of the owner. Be sure to leave with the
More informationINSTALLATION & OWNER S MANUAL
INDUSTRIES, LLC. INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 40 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KGL4AS) This Curtis Cab is designed and manufactured for use only as
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationINSTALLATION & OWNER S MANUAL
Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.
More informationINSTALLATION & OWNER S MANUAL
Pg. 1 of 14 INSTALLATION & OWNER S MANUAL John Deere Gator XUV 825i S4 Cab (p/n: 1GTRXUV4 Steel Cab with Doors) The contents of this envelope are the property of the owner. Be sure to leave with the owner
More informationINSTALLATION & OWNER S MANUAL
Page 1 of 18 INSTALLATION & OWNER S MANUAL John Deere 3 Family Premium Cab p/n: 1JD3FPR Standard Cab p/n: 1JD3FST Fits Tractor Models: 3033R, 3039R, 3046R Premium Cab Shown with Optional Front LED Work
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 15 INSTALLATION & OWNER S MANUAL John Deere Gator PathPro SS Cab (fits all HPX and XUV models with the O.P.S. system installed) (p/n: 1GTRXUV) (O.P.S. = Operator Protective Structure) The contents
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 13 INSTLLTION & OWNER S MNUL Kubota X 70 Series Cab (fits X2370, X2670, and X25D) (p/n: 1KX70S Steel Cab) (p/n: 1KX70SS Vinyl Cab) The contents of this envelope are the property of the owner. e
More informationINSTALLATION & OWNER S MANUAL
Rev. D, p. 1 of 29 INSTALLATION & OWNER S MANUAL YAMAHA VIKING YXM 700 ClearView Cab p/n: 1YAMVKCV fits model years up thru 2018 (fits Yanmar Bull model years up thru 2018) The contents of this envelope
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. 1 of 24 INSTALLATION & OWNER S MANUAL HONDA PIONEER 700-2 ClearView Cab p/n: 1HONP7002CV This cab fits model years up thru 2016. The contents of this envelope are the property of the owner.
More informationINSTALLATION & OWNER S MANUAL
Rev. B, p. 1 of 18 INSTALLATION & OWNER S MANUAL KAWASAKI TERYX ClearView Cab p/n: 1KAWT8002CV This cab fits model years: 2014- The contents of this envelope are the property of the owner. Be sure to leave
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. 1 of 24 INSTALLATION & OWNER S MANUAL HONDA PIONEER 700-4 ClearView Cab p/n: 1HONP7004CV fits model years up thru 2017 The contents of this envelope are the property of the owner. Be sure to
More informationINSTALLATION & OWNER S MANUAL
Rev. K, p. 1 of 11 INSTALLATION & OWNER S MANUAL POLARIS FREEDOM CAB INSTALLATION INSTRUCTIONS FOR THE POLARIS RANGER (p/n 2876196-067) IMPORTANT: THIS ACCESSORY WEIGHS 340 POUNDS. PLEASE ADJUST THE VEHICLE
More informationINSTALLATION & OWNER S MANUAL
Page 1 of 16 INSTALLATION & OWNER S MANUAL YAMAHA VIKING CAB KIT WITH HARD DOORS p/n: 1YAMVK fits model years 2014- (fits Yanmar Bull model years 2017-) NOTE: By design, the doors are made to not be removable!
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. 1 of 18 INSTALLATION & OWNER S MANUAL KUBOTA RTV 400 CAB (Not for use on RTV 500) These instructions are for installation of the complete cab as well as the modular components. DESCRIPTION:
More informationINSTALLATION & OWNER S MANUAL
Rev. K, p. 1 of 19 INSTALLATION & OWNER S MANUAL V4210 CAB KIT (color: orange) and/or V4220 CAB KIT (color: camo) INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.
More informationINSTALLATION & OWNER S MANUAL
Page 1 of 20 INSTALLATION & OWNER S MANUAL Massey Ferguson GC1700 Series All Steel Cab p/n: 1MFGC1700AS1 Soft Side Cab p/n: 1MFGC1700SS1 Fits Tractor Models: GC1705, GC1710, GC1715, GC1720 All Steel Cab
More informationINSTALLATION & OWNER S MANUAL
Page 1 of 30 INSTALLATION & OWNER S MANUAL John Deere 1 Family Premium Cab p/n: 1JD1FPR Standard Cab p/n: 1JD1FST Fits Tractor Models: 1023E and 1025R Premium Cab Shown with Optional Front LED Work Lights.
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL 1 of 24 John Deere 2 Family Cab p/n: 1JD2FCA Fits Tractor Models: 2032 & 2038R Available Options: 1. Front LED Work Lights (P/N: 9LEDW4) 2. Rear LED Work Lights (P/N: 9LEDW3)
More informationINSTALLATION & OWNER S MANUAL
Page 1 of 20 INSTALLATION & OWNER S MANUAL John Deere 4 Family Premium Cab p/n: 1JD4FPR Fits Tractor Models: 4044R, 4052R, 4066R Premium Cab Shown with Optional Front Work Lights. Available Options: 1.
More informationINSTALLATION & OWNER S MANUAL
1 of 12 INSTALLATION & OWNER S MANUAL KAWASAKI MULE Pro FX-FXT CORNER FLASHER KIT p/n: 1KAPFXCFL Required Accessories: Fuse Panel: Kawasaki P/N: KAF080-076 Or Curtis P/N: 1KAPFXFP Approximate Installation
More informationINSTALLATION & OWNER S MANUAL
1 of 24 INSTALLATION & OWNER S MANUAL Kubota BX80 Cab with Heater (p/n: 1KBX80CA) fits tractor models: BX1880, 2380 & 2680 Shown with front windshield wiper (comes standard with cab) Available Options:
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationSERVICE & OWNER S MANUAL
1 of 10 SERVICE & OWNER S MANUAL Product Specifications 25 x 36 x 7 Weight: 47 lbs. Air Flow: 260 CFM Air Conditioner p/n: 1ACUNIT-G1 Fits with Curtis Roof Kit: Contact Curtis for Details. Fits with Curtis
More informationINSTALLATION & OWNER S MANUAL
1 of 21 INSTALLATION & OWNER S MANUAL A/C Drive Kit for KUBOTA BX2670-1 and BX2680 p/n: 1ACBX2680DRK (Note: the alternator is supplied with a new pulley) Must be installed with one of the following three
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL V5008 Kubota RTV 72 Snow Blade The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation is complete. IMPORTANT: Please
More informationINSTALLATION & OWNER S MANUAL
P. 1 of 14 INSTALLATION & OWNER S MANUAL CAB INSTALLATION BEFORE YOU START HELPFUL REMINDERS: KUBOTA F-SERIES CAB p/n: F5206 The contents of this envelope are the property of the owner. Be sure to leave
More informationINSTALLATION INSTRUCTIONS DRAWERS #240
INSTALLATION INSTRUCTIONS DRAWERS #240 Please read and fill out the enclosed warranty registration card to activate your warranty. SHIPMENT CONTENTS #1 Lid #2 Rear #3 Left side panel #4 Right side panel
More informationFlip Top Installation Instructions
www.pavement-ends.com Flip Top Installation Instructions For: CJ7 1976-1986 Part Number: 44523 Wrangler/YJ 1986-1995 DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE LISTED ABOVE. WARNING This
More informationDriving Range Enclosure Kit Installation Instructions
Gasoline and Electric Vehicles: Carryall Carryall Carryall Plus Carryall 5 Carryall 6 Turf Turf Turf 5 Turf 6 XRT900 TransPorter TransPorter 6 Driving Range Enclosure Kit Installation Instructions Publication
More informationSPECIAL INSTALLATION INSTRUCTIONS
SPECIAL INSTALLATION INSTRUCTIONS WARN 4X FLARES FRONT AND REAR '98 TOYOTA HILUX DUAL-CAB As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.
More informationINSTALLATION INSTRUCTIONS
NEW HOLLAND MODELS T1530 CNH Original Parts INSTALLATION INSTRUCTIONS #710660156 ALL WEATHER CAB COMPACT TRACTORS 40273809 1 CARTON CONTENTS: ALL WEATHER CAB #710660156 Key# Part# Qty. Description 1 40274
More informationSupertop Installation Instructions
Supertop Installation Instructions For: CJ7 1980-1986 and Wrangler (All) Part Number: 51603 Rotary Latch Paddle Handle WARNING This product is designed primarily to enhance the appearance of the vehicle
More informationMOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB
MOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB FITS 4X2 & 6X4 GATORS A-11112, A-11224, A-11225, A-11226 MANUFACTURED BY: BOX 70 LITCHFIELD, MINNESOTA 55355-0070 (320) 693-3221 Fax: (320) 693-7252
More informationCANVAS DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
CANVAS DOOR KIT P/N 2882902, 2882903 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1J update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...
More informationQ15P. Mitsubishi MQ Triton Dual Cab
Mitsubishi MQ Triton Dual Cab Page 1 of 12 Fitting Instructions Part Number Mitsubishi MQ Triton Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationRIM Hood For Aeromaster Bodies
RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working
More informationINSTALLATION OF THE ENCLOSURE FOR THE MULE 3010 TRANS INSTALLATION GUIDE FOR THE MULE 3000 TRANS ENCLOSURE P. 1. Sept 07
INSTALLATION GUIDE FOR THE MULE 3000 TRANS ENCLOSURE P. 1 INSTALLATION OF THE ENCLOSURE FOR THE MULE 3010 TRANS Sept 07 www.essexmfg.com PO Box 92864 Southlake, TX 76092 Ph:888-643-7739 INSTALLATION GUIDE
More information2 Piece Soft Door Installation Instructions
2 Piece Soft Door Installation Instructions For: Wrangler/TJ (1997-on) Part Number: 51789 Note: Use of this product will eliminate the factory side mirrors and requires the removal of the entry light bulbs.
More informationINSTALLATION & OWNER S MANUAL
1 of 18 INSTALLATION & OWNER S MANUAL (*Not including cab & other accessories) A/C Alternator Kit: Yamaha Drive & Drive2 P/N: 1ACYDR2DRK Recommended it be installed with Curtis Cab: Sandstone (p/n 1GCYD1-A,
More information2015+ Mustang Rear Valance Installation Instructions P/N: (R F953) (R F953BS)
2015+ Mustang Rear Valance Installation Instructions P/N: 421894 (R1315-17F953) 421919 (R1315-17F953BS) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang Rear Valance Kit Installation
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS CLUB CAR PRECEDENT Champion and Professional Models Electric and Gasoline Models Beige (p/n 1CCP1A), Black (p/n 1CCP2A), White (p/n 1CCP3A) The
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More informationD40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws
HINGE # 1017 2 x Support Plate 1018 8 x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws 2 x Lid mount gas strut bracket 1041 2 x Self tap strut mount 1040 1 x Central Lock bracket 1510
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger (2009-) Straight UTV Steel Plow with Vehicle Mount Kit 6 Wide Snow Plow (p/n: 1POLSP) (fits the 500 H.O., 700 & 800 HD & XP) The contents
More information2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions.
Owner s Manual Model: Polaris RZR * 2011-up Polaris RZR 800* Cab Enclosure Kit Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents
More informationSupertop Installation Instructions
www.bestop.com Inc. Supertop Installation Instructions For: CJ7 ʻ76 -ʼ86 and ʻ86-ʼ95 Wrangler Part Number: 51598 DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE LISTED ABOVE. This product is
More informationCab Kit Installation Instructions
Low Speed Vehicles (LSV) Electric Vehicles: Carryall Carryall 6 Cab Kit Installation Instructions Publication 050770 These instructions apply to the following kit: 0670 Edition Code 008E09D GENERAL INFORMATION
More informationJODALE PERRY. Parts List & Mounting Instructions. Jacobsen HR9016 JDP BUILT FOR LIFE
JODALE PERRY Parts List & Mounting Instructions Jacobsen HR9016 JDP BUILT FOR LIFE Jacobsen HR9016 Mounting Instructions Standard Parts 1 - LH Rear Mounting Bracket 1 - RH Rear Mounting Bracket 1 - Front
More informationSCION tc STRUT TIE BAR Preparation
SCION tc 2005 - STRUT TIE BAR Preparation Part Number: 00016-80440 Code: YY1 Kit Contents 1 1 DS Mount Plate 2 1 PS Mount Plate 3 1 Cross Bar 4 1 Hardware Bag Hardware Bag Contents 1 4 8mm Screws 2 4 8mm
More informationInstallation Instructions I - Sheet Number I-TVR-01 Rev. A
Installation Instructions I - Sheet Number I-TVR-01 Rev. A TrailView Soft Top For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More information2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware
Owner s Manual Model: Polaris RZR * 2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationAir Conditioner for M915 A0/A1 Truck
RD-2-4530-0 Air Conditioner for M915 A0/A1 Truck INSTALLATION INSTRUCTIONS Install refrigerant compressor per instructions provided with compressor mount kit. CAUTION: Edges of sheet metal can be sharp!
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationInstallation Instructions
Installation Instructions TrailView Soft Top Important Safety Information For proper installation and best possible fit, please read all instructions BEFORE you begin. Periodically check all components
More informationPlace these instructions in vehicle s glove box after installation is complete. Clean Tonneau Cover with a mild detergent and water solution.
Place these instructions in vehicle s glove box after installation is complete Installation Time: Approx. 60 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS APPLICATION: DODGE CHARGER POLICE PUSH BAR (2011 & UP) APP PART # 36-2035 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 PUSH BAR ASSEMBLY RATCHET 2,3 2
More informationInstallation Instructions Sunrider
Installation Instructions Sunrider Vehicle Application Jeep CJ7 1976 1986 Part Number: 51698 Jeep Wrangler/YJ 1986 1995 Part Number: 51698 www.bestop.com - We re here to help! Visit our web site and click
More informationSUT-250-S (These instructions are used for SUT-250-SCLC also)
SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16,
More informationTOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation
Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear
More informationGeneral Front Windshield
General Front Windshield **WATCH OUR INSTALL VIDEO ALONG WITH INSTALL SHEET. 8-5/16-18x1 Black Carriage Bolts 8-5/16 Black Nylock Nuts 2-5/16x1-1/4 Stainless Steel Socket Head Screws 2-Rubber Grommets
More informationVOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationInstallation Instructions
Installation Instructions (2) 10-24 Black flathead Allen Screws Tailgate End Front Cover Passenger Side Rail (has inspected by sticker under rail) (4) 10-32 Screws (stainless) Front Cover Exploded View
More informationDOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882561, 2882562 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL UTV UNIVERSAL Plow Kit 6 Wide Snow Plow (Self Contained Hyd.) (p/n: 1UTVP = factory assembled) (p/n: 1UTVP-1 = assembly required) For the 1UTVP version, the instructions are
More informationINSTALLATION INSTRUCTIONS
NEW HOLLAND MODELS TC21DA TC24DA TC23DA TC26DA CASE MODELS DX21 DX24 DX23 DX26 CNH Original Parts INSTALLATION INSTRUCTIONS #710660106 ALL WEATHER CAB COMPACT TRACTORS 113901203 1 CARTON CONTENTS: ALL
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More information2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: (99-137)
2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: 422046 (99-137) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions
More information