PRESSURE UTILITIES. Pipe flow occurs due to contents of the pipe being pressurized System cannot have a free connection to the atmosphere
|
|
- Edwin Baldwin
- 5 years ago
- Views:
Transcription
1 PRESSURE UTILITIES Pipe flow occurs due to contents of the pipe being pressurized System cannot have a free connection to the atmosphere Types of Pressure Utilities Domestic Water: Clean/drinkable water Fire Water: Water for fire protection Process Water: Used in industrial processes Cooling Water: Used for AC or manufacturing Natural Gas, Compressed Air, Steam
2 PRESSURE UTILITIES Plans require specifying: Location (Horizontally): Dimension or station & offset Pipe size (sometimes material spec) Not needed: Length & slope
3 WATERLINE DESIGN Ohio EPA Peak Flows Domestic Water Average Daily Demand = OPEA Estimated Flow x Units Peak Daily Demand = Average Daily Demand x 2 (GPD) Peak Hourly Demand = Average Daily Demand x 10/1440 (GPM)
4 WATERLINE DESIGN ISO Method Fire Protection Required Flow = 1111 cc AA (GPM) A = Floor Area (SF) C = 1.5 Wood Construction = 1.0 Ordinary Construction = 0.6 Non combustible Construction Maximum Flows GPM Required flow rate may depend on insurance carrier
5 WATERLINE DESIGN Flow amount based on: Pipe Size Working Pressure Length of pipe Pipe Material Pipe Routing Use Hardy-Cross Method with Hazen-Williams equation for balancing flow in a pipe network Beyond scope of this class!!
6 WATERLINE STANDARDS Standard Working Pressures: psi Standard Test Pressures psi Minimum Pipe Sizes: Fire Hydrant Lead-in - 6 Diameter Residential Grid 6 Diameter (600 grid) Commercial Loops 8 Diameter Transmission Lines - 12 Diameter
7 WATERLINE STANDARDS Minimum Depths: 4 Cover (OEPA) 5 Cover (Toledo) 10 Cover in Eveleth, MN Avoid possibility of contamination!!!! 10 Min. laterally from parallel Sanitary Sewer 18 above a crossing Sanitary Sewer 12 clear to a crossing Storm Sewer
8 WATERLINE LAYOUT Looped Systems BUILDING Avoid dead end branches by looping systems Provided for multidirectional flows and redundancy in case of a line break Isolate sections of system with proper valve placement
9 WATERLINE LAYOUT Valve Placement Tell me where the breaks are going to be and I ll tell you where the valves should go! Roy Sidener Place valves to shut down sections of the system with least amount of disruption to operating lines intervals on straight lines In-line valves: Place on 2 branches of a Tee Place on 3 branches of a Cross Minor branches first Spurs to buildings on all 3 branches
10 WATERLINE Pipe Ductile Iron with gasketed joints Cement lined with zinc outer coating Standard push-on bell & spigot
11 WATERLINE Pipe: Ductile Iron with mechanical joints Provides extra secure connection
12 WATERLINE Pipe: Ductile Iron with restrained joints Requires retainer gland with setscrews into pipe
13 FITTINGS & APPURTENANCES Fitting Connections Tees & Crosses (with or without reductions) Reducers Bends 90, 45 or 22.5 only!!
14 FITTINGS & APPURTENANCES Gate Valves Rising Stem Wedge (gate) rises into body of the valve housing But the stem rises too! And we can t have a wheel underground!
15 FITTINGS & APPURTENANCES Gate Valves Non-rising Stem Stem is threaded into wedge Stem stays in place and gate rises into housing Still can t have a wheel underground!
16 FITTINGS & APPURTENANCES Gate Valves Curb Boxes Curb Boxes or Valve Boxes are used to access top of valve stem with wrench (key) for valve operation
17 FITTINGS & APPURTENANCES Post Indicator Valves PIV s are used on fire protection lines to clearly show the status of valve operation (OPEN or CLOSED) Valve body has a plate for indicator base flange attachment Many are monitored back to a central control station
18 FITTINGS & APPURTENANCES Fire Hydrants
19 FITTINGS & APPURTENANCES Fire Hydrants
20 FITTINGS & APPURTENANCES Fire Hydrants - Locations Local fire marshal dictates spacing: Depends on line sizes and pressures Usually from burning building Place behind curb at least 2-3 and accessible for pumper truck suction hose connection Locate in sight for ease of location clear of obstructions
21 FITTINGS & APPURTENANCES Tapping Sleeve & Valve Connection to existing lines can be done either by: Shutting down line, cutting out pipe and inserting a tee Using a Tapping Sleeve & Valve (Hot Tap)
22 FITTINGS & APPURTENANCES Tapping Sleeve & Valve
23 PRESSURE UTILITIES Hydrostatic Pressure Pressure in pipes can be compared to a height of water in a tank feeding the pipe If the pipe is capped at its outlet end, there will still be pressure on the cap trying to move it off the pipe If the cap is affixed to the pipe, then the pressure will try to move the pipe instead Joint restraints need to be used where pressure can push against the pipe and make it move
24 PRESSURE UTILITIES Thrust Blocks Thrust blocks are used to prevent buried pipe from moving under pressure are bends, tees and caps. The required bearing area is determined by Test pressure of the pipe Diameter of the pipe Fitting type Bearing capacity of the soil
25 PRESSURE UTILITIES Thrust Blocks Thrust blocks are used to prevent buried pipe from moving \
26 PRESSURE UTILITIES Thrust Blocks Sizing Rules of Thumb Height : Less than ½ trench height but greater than pipe diameter Width : 1 to 2 x block height
27 PRESSURE UTILITIES Thrust Blocks Practice Sizing Problem Determine the thrust block size for 45 Bend 8 Pipe Diameter Silt Soil 200 psi Test Pressure
San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS
San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS 834.1 DESCRIPTION: This item shall consist of fire hydrant installations using joint restraints in accordance
More informationFIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL. Item No.s/Description
FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL Item No.s/Description Item No. Description Material Specification HYDRANT Qty. Req d Item No. Description Material Specification 1 Operating
More informationVALVES, FIRE HYDRANTS, AND APPURTENANCES
VALVES, FIRE HYDRANTS, AND APPURTENANCES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Butterfly Valves B. Gate Valves C. Tapping Valve Assemblies D. Fire Hydrant Assemblies E. Flushing Devices (Blowoffs)
More informationSan Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS
San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS 834.1 DESCRIPTION: This item shall consist of fire hydrant installations using joint restraints in accordance
More informationGENERAL FEATURES / SPEC M&H AWWA C502 FIRE HYDRANTS Style 929 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approval Type: Compression type, opening against line pressure.
More informationAccording to AWWA-standard
According to -standard Water Fire fighting - UL/FM 304 Gate valves - Cast iron 320 Gate valves OS&Y 306 Service connection valves 322 Post indicators 306 Combi valves 307 Gate valves - 310 Gate valves
More informationvisit us online at
PRICE SHEET (PL-1014-VLV Replaces PL-0513-VLV) TABLE OF CONTENTS VALVES & HYDRANTS Page(s) Product Line Price Sheet 1 AWWA C515 Gate Valves NRS Series 2010 & 1010 PL-1014 Multiplier 2 AWWA C515 Gate Valves
More informationFLORIDA RURAL WATER ASSOCIATION 2970 Wellington Circle Tallahassee, FL Telephone: ~ Fax:
FLORIDA RURAL WATER ASSOCIATION 2970 Wellington Circle Tallahassee, FL 32309-6885 Telephone: 850-668-2746 ~ Fax: 850-893-4581 Lift Station Bypass Pump & Connection Assembly Instructions Loss of power during
More informationPIPE OUTSIDE DIAMETER GUIDE
June 7, 2018-1 PIPE OUTSIDE DIAMETER GUIDE PIPE OUTSIDE DIAMETER GUIDE - SMALL DIAMETER PIPE SIZES NOMINAL PIPE SIZES 1 /2" 3 /4" 1" 1 1 /4" 1 1 /2" 2" 2 1 /2" THIS O.D. GUIDE IS FOR YOUR CONVENIENCE &
More informationWater, Sewer & Drain Fittings
Why Compact? Compact Joint are manufactured from a high strength, impact resistant ductile iron that offers a great margin of safety against service failures and provides vastly increased resistance to
More informationSeptember 2012 / M&H C502 / Model 129
GENERAL FEATURES / GENERAL SPEC M&H AWWA C502 FIRE HYDRANTS Model 129 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approved Type: Compression type, opening against line
More informationSan Antonio Water System Standard Specifications for Construction ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS
ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS 836.1 DESCRIPTION: This item shall consist of grey-iron and ductile-iron fittings installation and adjustment installed in accordance with these specifications
More informationSan Antonio Water System Standard Specifications for Construction ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS
ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS 836.1 DESCRIPTION: This item shall consist of grey-iron and ductile-iron fittings installation and adjustment installed in accordance with these specifications
More informationSECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3
SECTION VIII (Sub-section 430) Wastewater Valves and Appurtenances Article Page 1. General 430-1 thru 430-2 2. Gate Valves 430-2 thru 430-3 3. Plug Valves 430-3 thru 430-4 4. Check Valves 430-4 5. Tapping
More informationMEDALLION HYDRANT. clowvalve.com AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY
clowvalve.com MEDALLION HYDRANT AWWA C50 UL LISTED FM APPROVED NSF 6/37 CERTIFIED 50 PSI WORKING PRESSURE 0-YEAR LIMITED WARRANTY Clow Valve, A Division of McWane, Inc. MEDALLION HYDRANT FIRE PROTECTION
More informationADMIRAL HYDRANT. clowvalve.com
clowvalve.com ADMIRAL HYDRANT AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 350 PSI WORKING PRESSURE AVAILABLE 10-YEAR LIMITED WARRANTY Clow Valve, A Division of McWane,
More informationBritish Standard institute-bs Valve Standards
BS 341-1:1991 Transportable gas container valves. Specification for industrial valves for working pressures up to and including 300 bar (REPLACED by BS EN 14189:2003), BS 341-3:2002), BS EN 849:1997),
More informationService Materials. Service Materials. With Three Locations to Serve You: Avoca, NY 8125 Kanona Rd. Avoca, NY (607)
Service Materials Service Materials Rochester, NY 785 Beahan Rd. Rochester, NY 14624 (585) 436-9624 With Three Locations to Serve You: Avoca, NY 8125 Kanona Rd. Avoca, NY 14809 (607) 566-2214 Watertown,
More information2009 Edition. Tyton fittings 14"-24" NSF. For Water & Wastewater, Fire Protection & Industrial Applications. Certified to ANSI/NSF 61
14"-24" Tyton fittings For Water & Wastewater, Fire rotection & Industrial Applications 2 Table of Contents TYTON Fittings 3 Assembly of TYTON Fittings 4 Bell Dimensions 6 Thickness and Dimensions 90 Bends
More informationTABLE OF CONTENTS. Pipe Diameter Chart (Reference Only)..50 Extensions 38,40,42,44
TABLE OF CONTENTS Item Page Item Page ANSI/AWWA Compact & Full Body Pipe Fittings: Product Submittals and Installation: Mechanical & Flange Joint C153. 3-9 20U Protective Fusion Bonded Epoxy....5,5 Mechanical
More informationTYLER UNION. Quality Waterworks Products. PC-2017, March, REGISTERED FIRMISO 9001:2015. Tyler Union
TYLER UNION Quality Waterworks Products WATERWORKS CATALOG PC-2017, March, 2017 www.tylerunion.com 10014257 U L REGISTERED FIRMISO 9001:2015 CERTIFIED Tyler Union 11910 CR 492 TYLER, TEXAS 75706 (800)
More informationData Sheet Issue A
General Description The Rapidrop Fig 601/602 dry barrel post / flushing fire hydrant is designed to be a trouble free, easy to maintain hydrant. The Fig 601/602 fire hydrant is rated for a working pressure
More informationFACILITY WATER DISTRIBUTION PIPING
SECTION 221113 - FACILITY WATER DISTRIBUTION PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationmh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY
mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY 129 HYDRANT YESTERDAY, TODAY, & TOMORROW For more than 85 years, the M&H
More information866.DIP.PIPE P 1 NSF Edition. Certified to ANSI/NSF Edition 4" 36" REVISED 11.09
P 1 4" 36" For FIRE PROTECTION, Water & Wastewater P 2 Table of Contents TR FLEX Restrained Joint Pipe and Fittings 4"-36" 3 Suggested Specification Wording For 4"-36" Restrained Push-on Joint Pipe and
More informationFire Protection Indicator Post
The 813 Series Indicator Post is designed to operate non-rising stem gate valves used in the control of underground water supply for automatic sprinklers, water spray deluge, foam-water deluge, and standpipe
More informationSECTION 5 AMERICAN. Ductile Iron Mechanical Joint Fittings
ECION 5 AMERICAN Ductile Iron Mechanical Joint Fittings he principal standards covering full body mechanical joint fittings are ANI/AWWA C110/A21.10 and ANI/AWWA C111/A21.11. Compact ductile iron fittings
More informationC909 PVC Pipe Patent Pending
1113 - H Copyright 2011 EBAA Iron, Inc. All Rights Reserved 19MJ00 Mechanical Joint Restraint for 4 through 12 inch C909 PVC Restraints for C909 PVC Pipe Patent Pending Features and Applications: For use
More information2150 F&I 4" PVC pipe LF 100 $ F&I 6" PVC pipe LF 100 $ F&I 8" PVC pipe LF 100 $ 90.00
1 of 5 2100 F&I 4" ductile iron pipe LF 200 $ 143.00 $28,600.00 2102 F&I 6" ductile iron pipe LF 200 $ 135.00 $27,000.00 2104 F&I 8" ductile iron pipe LF 200 $ 141.00 $28,200.00 2105 F&I 10" ductile iron
More informationBS 5163 Resilient Wedge Gate Valve
BS 516 Resilient Wedge Gate Valve BS 516 Flanged Resilient OS&Y Gate Valve, Type A, (XZ41X), /16, Gate valves serve to cut the medium flow in the piping system, widely used in the field of potable water,
More informationUtilities Catalog. PC-U2008, February, 2008
Utilities Catalog PC-U2008, February, 2008 Tyler Utilities 11910 CR. 492 Tyler, Texas 75706 (800) 527-8478 Union Foundry Company Box 309 Anniston, Alabama 3602 (800) 226-7601 TABLE OF CONTENTS Item Page
More informationPROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
More informationCLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION
CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION TESTING AND DESIGN SPECIFICATIONS (PER AWWA C502 / NSF /ULC & FM) 1. Hydrant shall be manufactured in accordance with AWWA C502 latest revision
More informationFINAL UTILITY REPORT Eastcreek Farm Thornton, CO
FINAL UTILITY REPORT Eastcreek Farm Thornton, CO October 14, 2016 JN: 13049 Prepared for: York 80, LLC 12460 1 st Street Eastelake, CO 80614 P: 303.457.2966 Prepared by: Jansen Strawn Consulting Engineers
More informationAWWA, RESILIENT WEDGE GATE VALVES
Type AVK Ref. # Size Weight kg lb US $ Series 04 Wrench nut Ductile Iron Series 08 Handwheel for AVK gate valves series 45, 55, 65 and 66 With bolt and washer Grey cast iron Size 1"-30" Series 18/45/55/65/66
More informationOPERATION AND MAINTENANCE MANUAL 5-1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT
OPERATION AND MAINTENANCE MANUAL 5-1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT INDEX 5-1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT OPERATION AND MAINTENANCE MANUAL OPERATION AND MAINTENANCE REPAIRS Operation
More informationSAN ANTONIO WATER SYSTEM
SAN ANTONIO WATER SYSTEM SAWS WATER JOB NO. 17-5026 2017 SMP MERRY ANN DR. FROM FRANCES JEAN TO DEAD END G:\TXC\Projects\SAWS\SAWS - Merry Ann\03_CADD\01_Sheets\Merry Ann_Water\01_Sheets\1 MANN WATR CVR.dwg
More informationmh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY
mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY 129 HYDRANT YESTERDAY, TODAY, & TOMORROW For more than 85 years, the M&H
More informationK81-DD FIRE HYDRANT GUARDIAN AWWA C502 NSF YEARS. For Generations CERTIFICATIONS ISO 9001 ISO BS OHSAS
GUARDIAN K81-DD FIRE HYDRANT CERTIFICATIONS ISO 9001 ISO 14001 BS OHSAS 18001 AWWA C502 NSF 61 140 YEARS WWW.KENNEDYVALVE.COM C For Generations COMPONENTS AND FEATURES A B C E D F G H J K M L N P Q S R
More informationValve Selection. 1. Function and service considerations
1. Function and service considerations Valve Selection Selection Valves serve the purpose of controlling the fluids in building services piping. Valves are produced in a variety of design types and materials.
More informationOPERATION AND MAINTENANCE MANUAL 5-1/4 AMERICAN-DARLING B-62-B-5 FIRE HYDRANT
OPERATION AND MAINTENANCE MANUAL 5-1/4 AMERICAN-DARLING B-62-B-5 FIRE HYDRANT INDEX 5-1/4 AMERICAN-DARLING B-62-B-5 FIRE HYDRANT OPERATION AND MAINTENANCE MANUAL OPERATION AND MAINTENANCE REPAIRS Operation
More informationPD Thrust Restraint Design Equations and Tables
Thrust Restraint Design Equations and Tables PD-6 5-95 These equations and tables are an effort to provide the piping system designer with conservative techniques and parameters for the design of underground
More informationTR Flex Pipe & Fittings DUCTILE IRON
TR Flex Pipe & Fittings DUCTILE IRON PIPE FABRICATION RESTRAINED JOINTS FITTINGS GASKETS COATINGS & LININGS CONTENTS GENERAL INFO Pipe 4" 36" 2 Suggested Specification Wording 3 ASSEMBLY INSTRUCTIONS Pipe
More informationFABRICATION TR Flex Pipe & Fittings DUCTILE IRON
PIPE FABRICATION TR Flex Pipe & Fittings DUCTILE IRON RESTRAINED JOINTS FITTINGS GASKETS COATINGS & LININGS CONTENTS GENERAL INFO Pipe 4" 36" 2 Suggested Specification Wording 3 ASSEMBLY INSTRUCTIONS Pipe
More informationSECTION 8 Fire Protection
Bronze Wet Barrel Fire Hydrants With over 100 years of experience on the west coast the heart of the wet barrel market James Jones Company, LLC is the innovator in the bronze wet barrel hydrant industry.
More informationPRODUCT MANUAL TRENCH ADAPTER
PRODUCT MANUAL TRENCH ADAPTER INDEX TRENCH ADAPTER PAGE INTRODUCTION... 8-2 FEATURES AND BENEFITS... 8-3 SPECIFICATIONS... 8-3 ORDERING Dimensions: Overall Dimensions and Weights... 8-4 Trench Depth and
More informationSUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION WATER DISTRIBUTION VALVES
SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION 33 12 16 WATER DISTRIBUTION VALVES PART 1 GENERAL... 2 1.1 Description... 2 1.2 Reference Specifications, Codes, and
More informationWater Distribution Solutions
Water Distribution Solutions Table of Contents WaterMaster 5CD250 Fire Hydrants 6 WaterMaster 5BR250 Fire Hydrants 8 FlowMaster Resilient Wedge Gate Valves 11 Valve Boxes 17 Meter Boxes 22 Table of Contents
More informationK81-D FIRE HYDRANT GUARDIAN AWWA C502 NSF YEARS. For Generations CERTIFICATIONS ISO 9001 ISO BS OHSAS
GUARDIAN K81-D FIRE HYDRANT CERTIFICATIONS ISO 9001 ISO 14001 BS OHSAS 18001 AWWA C502 NSF 61 140 YEARS WWW.KENNEDYVALVE.COM C For Generations COMPONENTS AND FEATURES A B C E D F G H J L M K N P Q S R
More informationSlide Gate Hydrant Maintenance Manual
Slide Gate Maintenance Manual Terminal City Iron Wks Ltd. Unit#3 99 19th Street, Langley, BC V1M 3C This Maintenance Manual is intended to give a guide to Maintenance. The Manual covers: Maintenance and
More informationSECTION 1019 VALVES AND APPURTENANCES GENERAL: Valves shall have manufacturer's name and pressure rating cast in raised letters.
SECTION 1019 VALVES AND APPURTENANCES Delete this Section in its entirety and replace with the following: SECTION 1019 VALVES AND APPURTENANCES 1019-1 GENERAL: Valves shall have manufacturer's name and
More informationP EDITION 4" 36" FOR FIRE PROTECTION, WATER & WASTEWATER REVISED 07.14
P 1 2014 EDITION 4" 36" FOR FIRE PROTECTION, WATER & WASTEWATER P 2 Table of Contents TR FLEX Restrained Joint Pipe and Fittings 4"-36" 3 Suggested Specification Wording For 4"-36" Restrained Push-on Joint
More informationFABRICATION TR Flex Pipe & Fittings DUCTILE IRON
PIPE FABRICATION TR Flex Pipe & Fittings DUCTILE IRON RESTRAINED JOINTS FITTINGS GASKETS COATINGS & LININGS CONTENTS GENERAL INFO Pipe " " Suggested Specification Wording ASSEMBLY INSTRUCTIONS Pipe & Fittings
More informationStandards for Design and Construction
Standards for Design and Construction Of Water, Wastewater, Fiber optics and Reclaimed Water Facilities For Pasco County Utilities Department Revised: March 2018 Board of County Commissioners: Kathryn
More informationUNION-TITE DUCTILE IRON C153 COMPACT FITTINGS
Sizes 4"-12" UL Listed for Fire Main Equipment SAMPLE SPECIFICATIONS (Current ANSI/AWWA revisions apply) 4" through 24" Push-On joint ductile iron fittings shall be produced in accordance with all applicable
More informationAMERICAN FLOW CONTROL TRENCH ADAPTER AND RETROFIT BOX INSERT
AMERICAN FLOW CONTROL TRENCH ADAPTER AND RETROFIT BOX INSERT TRENCH ADAPTER CONSTRUCTION PLASTIC CAP Helps seal upper stem section. 2-INCH SQUARE WRENCH NUT Allows the use of a standard 2 in. valve key.
More informationWater Distribution Solutions
Water Distribution Solutions Table of Contents WaterMaster 5CD250 Fire Hydrants 6 WaterMaster 5BR250 Fire Hydrants 8 FlowMaster Resilient Wedge Gate Valves 11 Valve Boxes 17 Meter Boxes 22 Table of Contents
More informationAVK SAUDI VALVES MANUFACTURING COMPANY
AVK SAUDI VALVES MANUFACTURING COMPANY AVK SERIES 24 - HIGH PRESSURE, WET BARREL HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION
More informationRESTRAINED JOINT HP LOK 30" 64" RESTRAINED JOINT NSF WATER & WASTEWATER. Certified to ANSI/NSF 61
2 0 1 6 30" 64" E D I T I O N NSF WATER & WASTEWATER NSF P 2 Table of Contents Restrained Joint Pipe and Fittings 30" 64" 3 Suggested Specifications for Restrained Push-On Joint Pipe and Fittings 4 Joint
More informationAmerican Flow control
American Flow control trench adapter and retrofit box insert FLOW CONTROL Trench Adapter Construction Plastic Cap Helps seal upper stem section. Lid Securely retained by rotating 90. Stainless steel bolt
More informationFIRE PROTECTION PRODUCTS
SUPER CENTURION FIRE HYDRANT Mueller Super Centurion Fire Hydrant Since its introduction in 1976, millions of Centurion fire hydrants have been installed throughout North America. There are a number of
More information516509_tabs 11/16/10 4:55 AM Page 1 FIRE HYDRANTS
Date Printed: November 2010 FIRE HYDRANTS or Tyton (6"),6, or 8" A EDDY FIRE HYDRANTS PARTS LIST WORKING PRESSURE: 150 PSI Note: Discontinued For Reference Only 350 PSI Working Pressure
More informationUBC Watermain as shown on Sheet 202 : Sub total 97,050
Preliminary Cost Estimate Brock Commons Phase 1 Watermain replacement UBC Portion of Works only Replace existing 150mm dia CI and 200mm dia AC watermain with 200mm & 250mm dia DI (ductile iron) watermain
More informationEXPECT RELIABILITY AVK RESILIENT SEATED GATE VALVES
EXPECT RELIABILITY AVK RESILIENT SEATED GATE VALVES AVK VALVES STANDARD FEATURES AVK STANDARD FEATURES AVK Gate Valves are made of ductile iron and meet or exceed AWWA C509 or C515 ASTM A582 stainless
More informationDepth of Bury Tables 9B-5. A. General. B. Rigid Pipe Assumptions. Design Manual Chapter 9 - Utilities 9B - Trench Design
Design Manual Chapter 9 - Utilities 9B - Trench Design 9B-5 Depth of Bury Tables A. General The depth of bury tables on the following pages are based upon the design methodology from the various pipe material
More informationof wet barrel hydrants, hydrant valves and hydrant tools.
JONES WET BARREL FIRE HYDRANTS The most complete selection of wet barrel hydrants, hydrant valves and hydrant tools. Bronze wet barrel fire hydrants Jones is the leader. With over 100 years of experience
More informationPVC Pressure Piping Systems for Water Transmission
PVC Pressure Piping Systems for Water Transmission MUNICIPAL SYSTEMS PVC PRESSURE PIPING SYSTEM MANUFACTURED TO AWWA & CSA STANDARDS IPEX Centurion 14" 60" (350mm 1,500mm), AWWA C905 and CSA Standards
More informationBritish Standard Underground Hydrant Range
AVK UNDERGROUND HYDRANTS British Standard Underground Hydrant Range THE AVK BRITISH STANDARD HYDRANT RANGE AVK are the renowned market leading innovators, manufacturers and suppliers of BS 750 fire hydrants
More informationAPPROVED MATERIALS LIST SERVICE MATERIALS July 2017 **REVISED 12/6/17**
APPROVED MATERIALS LIST SERVICE MATERIALS July 2017 **REVISED 12/6/17** SIZE DESCRIPTION MANUFACTURER & MODEL NUMBER CORPORATION STOPS 1" MIP x GRIP Comp ball corp stop Ford: FB 1100-4Q McDonald: 74704-BQ
More informationTriton. Wet Barrel Ductile Iron. Fire Hydrants. Reliable Connections. operation / Maintenance manual. Inspection and Installation 2
operation / Maintenance manual MUELLER TAble of contents PAGE Triton Inspection and Installation 2 Installation and Testing 3 Wet Barrel Ductile Iron Maintenance Instructions 4 Parts 5 Notes 6-7 Fire Hydrants
More informationDELETE first sentence of first paragraph that reads: REPLACE with the following:
To Bidder of Record: SAN ANTONIO WATER SYSTEM Addendum 2 To Construction Documents For 2012 WATER & SEWER CONSTRUCTION CONTRACT, PACKAGE I SAWS WATER JOB NO. 12-5001 SAWS SEWER JOB NO. 12-5501 Solicitation
More informationAMERICAN AVK COMPANY AVK SERIES 67 - HIGH PRESSURE, POST/FLUSHING HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS
AMERICAN AVK COMPANY AVK SERIES 67 - HIGH PRESSURE, POST/FLUSHING HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION RECEIVING
More information2-inch operating nut (other options available) 10 millimeter fusion-bonded epoxy coating (NSF-61) Triple O-ring seal
InsertValve The Team InsertValve TM is a fully functioning, resilient wedge gate valve with a rated working pressure of 250 psig. The valve fully closes, and it provides a clear, unobstructed waterway
More informationANNEX 2. Scope of Works 1.0. Introduction. The United. joint pipes and lengths, iv items. and testing. all tests and 2.0.
ANNEX 2 Pre Shipment Inspectionn and Testing of Ductile Iron Pipes Scope of Works 1.0 Introduction The United Nation intends to procure ductile iron pipes, fittings and valves from China and Italy. The
More informationSECTION VALVES PART 1 -GENERAL
SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This
More informationTYLER UNION IMPORT RESTRAINTS LP NR
SERIES 1000 MJ TUFGRIP WEDGE TYPE RESTRAINT FOR DUCTILE IRON PIPE MJ TUFGRIP for DI Pipe - GLAND ONLY N70-5760 MJ TUFGRIP for DI Pipe - W/ ACCESSORIES N71-6795 3 113805 $42.94 7 150 3 114352 $65.05 10
More informationTrack Drive Circuit - General System. Simplified Travel Circuit Diagrams: Neutral Controls Forward Travel Reverse Travel
Section 7.1 Track Drive Circuit - General System Simplified Travel Circuit Diagrams: Neutral Controls... 7.1.2 Forward Travel... 7.1.4 Reverse Travel... 7.1.5 General... 7.1.3 Track Drive Circuit: General...
More informationCombustion Technologies By-Pass Filtration Instructions
Combustion Technologies By-Pass Filtration Instructions www.combustionusa.com Made in the USA Date Revision Jan 17 th, 2013 PLEASE READ AND UNDERSTAND ALL INSTALLATION INSTRUCTIONS PRIOR TO BEGINNING THE
More informationJoint Restraint System
Joint Restraint System For IPS, DPS & DIN Plastic Pipe 10-YEAR Warranty Parts & Labor ask for details PIPE TO FITTING LH-Series 2-12 IPS Pipe s LHD-Series 4-24 DPS Pipe s DLH-Series 63-400MM DIN Pipe s
More information2-6 FIRE HYDRANT---(MODEL ½ & 5 ¼
M&H PDF PAGE INDEX Page PRODUCT 2-6 FIRE HYDRANT---(MODEL 129 4 ½ & 5 ¼ ) 7 How to Order Fire Hydrants 8 FIRE HYDRANT WARRANTY 9-13 FIRE HYDRANT---(MODEL 929 5 ¼ ) 14-18 FIRE HYDRANT---(POST HYDRANT 2
More informationSeries 1500TD Bell Restraint Harness for Ductile Iron & C900 PVC Pipe Split Serrated Restraint Rings on Both Sides of the Bell
Series 00TD Bell Restraint Harness for Ductile Iron & C900 PVC Pipe Split Serrated Restraint Rings on Both Sides of the Bell Features and Applications: Restraint for Ductile Iron Pipe at Push- On Bells,
More informationEngineering & Design Data
PVC & CPVC Corrosion Resistant Industrial Pressure Pipe Engineering & Design Data Engineering & Design Data Hydraulic Shock Hydraulic shock is the term used to describe the momentary pressure rise in a
More informationPVC WELL CASING & FITTINGS 20 FT. BELL-END /8 SDR21 REDUCING COUPLINGS STEEL WELL CASING & FITTINGS
Pipe Pipe & Well Casing FT. BELL-END 0 7 293 2 2 29 27 23 " SCH0 -/2" SDR7 " SDR2 " SCH0 " SCH0 FT. BELL-END 37 32 30 29 2 " SCH0 -/2" SDR7 -/" DR27. PVC WELL CASING & FITTINGS FT. BELL-END 003 7 -/ SDR2
More informationSTANDARD DRAWING INDEX
ATTACHMENT B STANDARD DRAWING INDEX DESCRIPTION EXISTING DRAWING NO. GENERAL Typical Layout for Improvement Plans City of Stockton Standard Border and Title Block for 8 1/2 x11 Sheet City of Stockton Standard
More informationJUST PIPING, JUST FITTING. A Comprehensive Integrated Solution For Piping Systems
JUST PIPING, JUST FITTING A Comprehensive Integrated Solution For Piping Systems SF 01 DUCTILE IRON PIPE FITTINGS FD1011 FD1021 FD1022 FD1031 FD1102 FD1103 FD1111 FD1121 Double Flanged Piece Flanged spigot
More informationRated to the New, Higher Pressure Classes in Latest Editions of AWWA C900 and C909. Joint Restraint Products
Pipe Restrainers series 1000G2 1000G2C Restrainers for AWWA CI OD C900/C909 PVC/PVCO Pipe with MJ or Ductile Iron Push-On Fittings (Formerly Series 9000) INFORMATION Second Generation (Gen 2) PVC Restrainers
More informationMueller Super Centurion 250 Fire Hydrant
Mueller Super Centurion 250 Fire Hydrant Designed for efficient flow and outstanding, long-term reliability Mueller Super Centurion 250 Fire Hydrant...250 psig rating, high flow, dependable performance,
More informationAmerican Flow control Series 2500
American Flow control 14-66 Series 2500 Resilient wedge gate valve FLOW CONTROL Construction Ductile iron operating nut Provides strength and durability. Lifting DEVICES 14-66 Valve is constructed of high-strength
More informationJEFFERSON UTILITIES 270 INDUSTRIAL BLVD. KEARNEYSVILLE, WV (304) STANDARDS AND SPECIFICATIONS
JEFFERSON UTILITIES 270 INDUSTRIAL BLVD. KEARNEYSVILLE, WV 25430 (304) 728-2077 STANDARDS AND SPECIFICATIONS FEBRUARY 28, 2018 1 TABLE OF CONTENTS GENERAL MATERIAL... 3 WATER... 5 DUCTILE IRON PIPE...
More informationAvailable End Connections & Size Range
ECCENTRIC PLUG VALVES Size Range 3"-24" Water Working Hydrostatic Size Range Pressure psi Test psi 3"-12" 175 350 14"-24" 150 300 Available End Connections & Size Range Figure No. Flanged 3"-24" F-5412
More informationV A L V E S. rice List of. Controlling fluids is our expertise TERMS & CONDITIONS : An ISO:9001 Co. PRICE LIST NO. : JMW / 3 0 W.E.
V A L V E S Controlling fluids is our expertise TERMS & CONDITIONS : This cancels our all previous issues. All prices are Ex. works, Jalandhar. Excise duty will be charged extra as applicable (presently
More informationSECTION 17 FIRE HYDRANT ASSEMBLIES General
SECTION 17 FIRE HYDRANT ASSEMBLIES 17-1.01 Scope 17-1 General This section describes the requirements for furnishing and installing as appurtenances to treated water mains. These requirements include the
More informationKENNEDY VALVE KS-RW RESILIENT WEDGE VALVES
KENNEDY VALVE KS-RW RESILIENT WEDGE VALVES KENNEDY VALVE AWWA C515 Resilient Wedge Gate Valves Meet or Exceed the Requirements of AWWA Standard C515 UL-262/FM-1120/1130 ULC-Underwriters of Canada 2 1/2
More informationBALL VALVES. Industry-Leading 300psi Low Lead Ball Valves
BALL VALVES Industry-Leading 300psi Low Lead Ball Valves Designed and Manufactured to Meet Your Needs 1 Lockwing Accepts bullet lock (when equipped on meter valve). 2 Stainless steel reinforced seat gaskets
More informationBUTTERFLY VALVES. An industry leader in underground and in-plant applications. STYLE STYLE Consult factory for sizes
An industry leader in underground and in-plant applications. BUTTERFLY VALVES STYLE 4500 3 24 STYLE 1450 30 54 Consult factory for sizes 60 120 C504 Class 150B & 250B M&H Valve is a division of McWane,
More informationFormstücke, Flanschendruckrohre. und Armaturen. Index: (click with mouse) Fittings, Flanged pipes and Valves made of Ductile Cast Iron ( GGG )
FITTINGS AND VALVES Index: (click with mouse) Formstücke, Düker in general Flanschendruckrohre Preamble und Armaturen aus The complete duktilem product Gusseisen range ( GGG ) > Index Location plan Flag
More informationSECTION FIRE HYDRANTS WITH HYDRANT LOCKS
SECTION 33 12 19 FIRE HYDRANTS WITH HYDRANT LOCKS PART 1: GENERAL 1.01 SCOPE A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 SUBMITTALS A. Conform to requirements of Section 01 33
More information1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service.
KENNEDY KENNEDY VALVE MODEL VALVE KS-RW 1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service. 2. The valves shall have a cast
More informationWater Connection Repair Method and Techniques
Water Connection Repair Method and Techniques LINE LOCATES APWA Colour Codes Representatives from utility companies can field locate their lines if required. Excavation Ensure excavation is on the opposite
More informationAmerican Flow control 5 1/4 b-84-b-5
American Flow control 5 1/4 b-84-b-5 Fire Hydrant FLOW CONTROL Construction Fully complies with AWWA C502 and is available UL Listed and FM Approved in applicable configurations. one-piece bronze OPERATING
More information