WOLF CLASS LUCIUS PATTERN WARHOUND TITAN
|
|
- Katrina Little
- 5 years ago
- Views:
Transcription
1 TM PISTONS SHEET 1 OF 6 ASSEMBLY OPTIONS Cut all pistons to required length depending on foot position. NOTE: It can be useful to support the sole of the foot in the position required when building the toes. SMALL TOE PISTON X12 TOE PISTON X6 THIGH PISTON X2 ANKLE PISTON X10 KNEE PISTON X2 HIP PISTON X6 Illustrated above are the various types of pistons and piston sleeves used to construct the legs of the Titan. The pieces are shown as supplied with the casting gates. You will need to cut off these gates. It is recommended that you identify each piece before assembly. You will need to trim each piston to achieve the desired pose for your model. REAR TOE JOINT TOE PISTON PART 2 Cut to required length) FRONT TOE TIP (check this is the largest toe with an Imperial Eagle Underneath.) REAR TOE SMALL TOE PISTONS (Cut to required length) TOE PISTON PART1 BUILDING AND PAINTING THE MODEL The Warhound Titan is a complicated model kit. For best results we recommend to take your time to assemble it. Besides the tools you would normally need to assemble plastic or metal models you will need the following: a razor saw, several different grades of sandpaper or sanding pads, a set of files and modelling clippers. Of course you will also need some glue. Citadel Super Glue will work perfectly. It is possible to assemble your model in an almost limitless choice of poses.to achieve the desired pose we recommend dry fitting each assembly before gluing. It may be easier to paint the model before certain parts such as the leg armour plates are assembled. SOLE FRONT TOE JOINT MIDDLE TOE JOINT SIDE TOE TIP Copyright Games Workshop Ltd., All rights reserved. Product code : IAW001 Forge World, Games Workshop, Willow Road, Lenton, Nottingham, NG7 2WS, UK. Tel (0)
2 FRONT VIEW LOWER THIGH SHEET 2 OF 6 BOTH AND ARE ASSEMBLED WITH AN IDENTICAL SET OF PIECES KNEE PISTON PART 1 KNEE PISTON PART 2 LOWER LEG ASSEMBLY OPTIONS Armour mount on leg must face forward REAR VIEW HIP JOINT HIPS ANKLE PISTON PART 2 UPPER THIGH ANKLE PISTON PART 1 ASSEMBLY OPTIONS Cut all pistons to required length depending on leg position. REAR THIGH PISTON PART 1 REAR THIGH PISTON PART 2 HIP PISTON PART 1 HIP PISTON PART 2 FOOT ASSEMBLY
3 ADEPTUS MECHANICUS SHRINE SHEET 3 OF 6 SERVITOR BODY REAR DOORWAY LEFT CARAPACE MAIN BODY ELEVATOR WINCH RIGHT CARAPACE MAIN BODY ASSEMBLY SERVITOR IMPERIAL COMMISSIONING PLATE CREW ELEVATOR
4 SHEET 4 OF 6 The empty chair can replace the chair with the Princeps if you do not wish to have the crew in your Titan or wish to create your own commander WALL PANEL1 PRINCEPS RESTS WALL PANEL 2 MODERATAI SERVO SKULLS Four included in the kit MODERATAI BASE
5 SHEET 5 OF 6 GUN SIGHT CABLE CONNECTORS SHIELD TURBO LASER BARRELS TURBO LASER ASSEMBLY CABLE PORTS Included in the kit are several lengths of rubber cabling. These need to be cut to the required length and positioned between the head and weapons and the body. A cable connector is fitted to the end of each gun cable and one end of each head cable. PLASMA BLASTGUN WEAPON ARM COLLAR CABLE & CABLE CONNECTORS ASSEMBLY BODY RO ETCHED STEEL GRILLE NOTE PLASMA CYLINDERS BODY ROOF VENTILATOR BANK Insert steel grille between BODY ROOF and VENTILATOR BANK CABLES, CABLE PORTS & CABLE CONNECTORS SERVITOR HATCHES CENSER
6 SHEET 6 OF 6 UPPER HATCHES Included in the kit are various symbols & seals. View the surrounding pictures to see their suggested position or select a position of your own. Also included is a sheet of clear plastic which can be cut to the required shape to produce windows for the head. MAIN VENTS REACTOR EXHAUSTS VOID SHIELD PROJECTORS FRONT ROOF WAIST ARMOUR UPPER LEG ARMOUR TOP LOWER LEG ARMOUR
PARTS IDENTIFICATION AND ASSEMBLY INSTRUCTIONS
The U.S. M10 ammunition trailer was used mostly by armored units to transport additional ammunition. It could be towed by many different vehicles, including 2 ½ ton trucks, half tracks, armored cars, self-propelled
More informationThe Sidewinder Wheeled Armoured Personnel Carrier.
The Sidewinder Wheeled Armoured Personnel Carrier. The sidewinder APC is a simple wheeled vehicle I scratch built. This document will provide you with the information to duplicate it for yourself. This
More informationTools Required. Saw. Knife. Side cutters. Pin vice. Plastic glue. Superglue.
Page 1 of 6 Guide to Converting an Ork War Buggy From a Trukk Kit. Introduction. At this time (April 2013) the war buggy kit available from Games Workshop is the same kit that was available during the
More informationADEPTUS MECHANICUS TITAN LEGIONS Divisio Militaris Army List 1.0
ADEPTUS MECHANICUS TITAN LEGIONS Divisio Militaris Army List 1.0 Special Rules Titan Weapons Titans from the same Forge World or Legio will often have a variety of weapons among them. Sometimes these differences
More informationTable of Contents. Tail Wheel Assembly Installation.. page 01. Stabilizer Installation.. page 02. Fin Installation.. page 03
Table of Contents Tail Wheel Assembly Installation.. page 01 Stabilizer Installation.. page 02 Fin Installation.. page 03 Elevator and Rudder Hinge Installation.. page 04 Rudder Controls.. page 05 Elevator
More informationBuild your own. Pack. Stages 39-42: Receive more of Robi s electrical components
Build your own Pack 11 Stages 39-42: Receive more of Robi s electrical components Build your own All rights reserved 2016 CONTENTS Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne
More informationUser Manuel. Titan Hummer XL
User Manuel Titan Hummer XL Dear User, Tzora Active Systems Ltd. thanks you for choosing the Titan Hummer-XL and wishes you safe and enjoyable journeys. For proper operation and to maintain the scooter
More informationAutomatic magazine and weather protection housing IC presentasjon 07 1
Automatic magazine and weather protection housing 1 Introduction To improve the efficiency in anti aircraft defence, an automatic magazine for the L70 gun has been developed. The idea was to design a system
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS.
TITAN pt. no.: 02 0000 0209 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS Gen6 Extended Capacity Replacement
More informationSERVICE MANUAL. Seat system for electric wheelchair
SERVICE MANUAL US VS Seat system for electric wheelchair How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilusa.com
More informationHoustoun Gate Locomotive Works Gordon 4-Wheel Drive Chassis Assembly Instructions
Houstoun Gate Locomotive Works Gordon 4-Wheel Drive Chassis Assembly Instructions It is suggested that you read these instructions through before commencing construction. A minimum of tools are needed
More informationSuper Dragon Glow Conversion
Super Dragon Glow Conversion Kit Contents: Kit # AG-501 Wood Bag: Qty......Name.......................................Description 1.......LC-G501-01.................................3mm X 6 X 24 Laser Cut
More informationBuilding Integrated Duct System
Mounting instruction Building Integrated Duct System Description We are facing one of the toughest challenges in decades. New buildings and existing homes must minimize their use of energy. In less than
More informationSetting Up the NESS L300 Plus System
7 Setting Up the NESS L300 Plus System Preparing the Skin Before you put on the L300 and Thigh FS Cuffs, prepare your skin where the electrodes will touch. To prepare your skin: 1. Clean the skin where
More informationAdeptus Astartes Scions of Iron. Victory Through Heavy Armour
Adeptus Astartes Scions of Iron Victory Through Heavy Armour 1.0 Chapter Brothers. In the beginning we were forced to fight without the support of our Armoured columns. The Orks forced our hands but we
More informationDoor panel insert trim replacement Volvo V70
Door panel insert trim replacement 1998-2000 Volvo V70 Tools needed: Torx Driver T25, Putty Knife, Bone Tool (optional), Heat gun or Dremel cutting tool, wire brush (or use a plastic tile and grout brush),
More informationto fly. Most hardware included and all replacement parts are available.
Instruction Manual The Thunderbolt P47 was perhaps the greatest of world war II in terms of all round performance and capability Phoenix Model has recreated a 2C - 60 class engine (or 4c 91 class) It was
More informationSupplemental Instructions for Walkera F-16
Supplemental Instructions for Walkera F-16 Step 1 the instructions show a brushed motor setup and indicate you should solder 3 capacitors to the motor terminals. The kit actually contains a brushless motor,
More information1:8 scale Koban Model Documentation
1:8 scale Koban Model Documentation Gear-foot assembly The gear foot consists of three parts, the gear-foot, prop shaft, and propeller. Clean flash from castings being careful to keep the mating surfaces
More informationASSEMBLY AND USER GUIDE
ASSEMBLY AND USER GUIDE "DESIGNED FOR THE OPTIMAL GAMING EXPERIENCE AND UNPARALLELED COMFORT" Congratulations on purchasing your EDGE GX1 gaming chair. The chair has several important adjustments. Spending
More informationDassault Aviation FALCON 7 X. for Jet CAT P160. Assembly Manual. AVIATION Design
Dassault Aviation FALCON 7 X for Jet CAT P160 Assembly Manual AVIATION Design ZI le chenet, 91490 Milly La Foret, FRANCE Tel : 33 1 64 98 93 93 Fax : 33 1 64 98 93 88 E-mail : aviation.design@wanadoo.fr
More informationPush Type Gas Springs
Push Type Gas Springs ICTATOR high-performance push type gas springs make life easier by lifting loads smoothly and effortlessly. We have a vast product range with many potential applications. We manufacture
More informationRevell F-117 Stealth Fighter. 1/48 th Scale Kit # 5834
Revell F-117 Stealth Fighter. 1/48 th Scale Kit # 5834 By Mark Murray I won t go into the history of this aircraft, as it s offered by many other sources, far better than I can expound upon. Suffice it
More informationAssembly Manual. AVIATION Design
SCORPION Assembly Manual AVIATION Design ZI le chenet, 91490 Milly La Foret, FRANCE Tel : 33 1 64 98 93 93 Fax : 33 1 64 98 93 88 E-mail : aviation.design@wanadoo.fr www.adjets.com Version 01/09/2009 AVIATION
More informationTrainer Assembly Manual
Trainer Assembly Manual www.pilot-rc.com -Pilot Trainer- 1 -Pilot Trainer- 2 -Pilot Trainer- 3 -Preliminary i wing & stab assembly- 1-) Locate both Plywood wing joiners (Large and small one) 2-) Insert
More informationTHE T IN DETAIL
STEP 17 THE T-34-85 IN DETAIL The T-34 tank, can, without exaggeration, be regarded as the world s first universal tank, and yet its creators did not have the slightest inkling that this was the case.
More informationPilotRC Trainer USER MANUAL
PilotRC Trainer USER MANUAL Introduction Thank you for purchasing our Trainer plane. we strive to achieve a good quality quick build ARF aircraft. It requires the least amount of assembly of any ARF kit
More informationJK Upper 1/2 Door Installation Instructions. Front 1/2 Door Installation
JK Upper 1/ Door Installation Instructions Upper Soft Door Kit (Front) dr - 4dr JK : 13711.15 Upper Soft Door Kit (Rear) 4dr JK: 1371.15 Front Door Content: 13711.15 (dr/4dr) 1. Soft Upper Door frame with
More informationHD-Series. Shop Equipment
HD-Series Shop Equipment Reaching new heights Winntec (Est. 2002) is a manufacturer, esteemed developer and international supplier of high quality, efficient and reliable automotive workshop essentials,
More informationAssembly Manual. Version 01/01/2006
Assembly Manual ZI le chenet, 91490 Milly La Foret, FRANCE Tel : 33 1 64 98 93 93 Fax : 33 1 64 98 93 88 E-mail : aviation.design@wanadoo.fr www.adjets.com Version 01/01/2006 INTRODUCTION is our new jet
More informationAthearn Pacific Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Overview This application note describes how to install a DSD-100LC Digital Sound Decoder into the Athearn Pacific Locomotive. All of the
More informationArmor How-To KITBASHING DRAGON S T-34/85M
Armor How-To KITBASHING DRAGON S T-34/85M 58 FineScale Modeler December 2002 1/35 Scale Story and photos by Peter Rasmussen A scratchbuilt turret turns a T-34 into a modern-era tank killer Combining ICM
More informationOFFROAD 2014 APPAREL
OFFROAD 2014 APPAREL 034 035 OFFROAD 2014 APPAREL 450 APPAREL SCOTT s 450 MX apparel is the top of the line. Made with the best materials available, the 450 line is the most functional, lightweight and
More informationABS lifting station Synconta
15975187GB (03/2006) 106800 GB Installation and Operating Instructions www.absgroup.com Installation and Operating Instructions 601 801 901 901L 902 902L Contents 1 General... 3 1.1 Application areas...
More information4mm scale 009 gauge Lodge Hill & Upnor railway Chattenden Drewry loco body kit.
RT Models 4mm scale 009 gauge Lodge Hill & Upnor railway Chattenden Drewry loco body kit. HISTORY The loco was supplied by the Drewry car co. to the Lodge Hill & Upnor Railway in 1949, works number 2263.
More informationmit Simmering Sla.16 Pz.Kpfw. VI Ausf. B (H) Deutschland, 1945 Henschel-Werke German Heavy Tank * «Steel Generals» - series of paper
models of armored vehicles War Thunder «Steel Generals» - series of paper German Heavy Tank Pz.Kpfw. VI Ausf. B (H) mit Simmering Sla.6 Henschel-Werke Deutschland, 945 0 German Heavy Tank King Tiger In
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1404mm (55.3in) - Length: 1134mm (44. 6 in) - Flying weight: 3.2-3.4 kg - Covering type: Genuine ORACOVER - Spinner size: scale type (not included) - Radio: 4 channel minimum
More informationCorpus II/Trax. Seat for electric wheelchair Trax. Owner s manual
Corpus II/Trax Seat for electric wheelchair Trax Owner s manual US How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilus.com
More informationFurness Railway Coach Co.
Furness Railway Coach Co. Outside Framed Coaches Paint and transfers required to complete. Part 32 Part 7/8 Part 9 Part 6 Part 31 Part 14 The Parts. Part 19 Parts 20/21/22 Part 5 Part 4 Part 1 Part 3 Part
More information700 bar Hand Pump BT-715
BT-715 700 bar Hand Pump BT-715 This basic hand pump can be used with all BOLTIGHT 700 bar tooling and equipment. The pump has both high and low pressure pistons and is supplied complete with, a 63 mm
More informationPRESCRIPTION FORM. Delivery address. Purchase order. Shipment date Delivery Date. Type
PRESCRIPTION FORM Distributor Branch Client Phone Delivery address (Use 'Shift'+'Enter' for new line) Salesperson E-mail Purchase order Type Date Shipment date Delivery Date Important Demo Request Order
More informationARDEC Rapid Design Projects for Field Support Part 1
ARDEC Rapid Design Projects for Field Support Part 1 L-Bracket for use with M240B Medium Machine Guns on HMMWVs with Gunner s Protection Shield (NSN 2510-01-498-4996) Michael Narus Robert Mulfinger Anthony
More informationustepper - Robot Arm Assembly instructions Microcontroller, stepper driver and encoder in an ultra-compact design! By ON Development IVS
ustepper - Robot Arm Assembly instructions Microcontroller, stepper driver and encoder in an ultra-compact design! By ON Development IVS 2016 ON Development IVS All Rights Reserved Assembly notes The parts
More informationFurness Railway Wagon Co. NER/LNER/BR C1 5ton Fitted Open Fish
Furness Railway Wagon Co. NER/LNER/BR C1 5ton Fitted Open Fish Wheels, paint and transfers required to complete. Please note that to aid the folding of the various parts score all the halfetched foldlines
More informationCONCEPT MODELS CPOX 820 SCHNABEL CAR W. Canyon Creek Dr. Maricopa, AZ Web Address:
CONCEPT MODELS Web Address: http://www.con-sys.com 44609 W. Canyon Creek Dr. Maricopa, AZ 85239-5019 CPOX 820 SCHNABEL CAR 2 CONCEPT MODELS PARTS Item No. PAR T NO. DESCRIPTION QTY. 1 6519-1 Right Girder
More informationSBACH SCALE 1:4 ½ ARF
SPECIFICATION - Wingspan: 1663mm (65.5 in) - Length: 1638mm (64.5 in) - Flying weight: 4700-5200 gr - Wing area: 56 dm2 - Wing loading: 85g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationA Never-Ending Demolition Derby
A Never-Ending Demolition Derby The demolition derby has always held a special place in our culture. Not unlike Ultimate Fighting, the spectacle is simple: Two cars enter, one car leaves. Problem is, once
More informationMAKING MODERN LIVING POSSIBLE. Danfoss Air. Installation manual for Danfoss Air Flex duct systems DANFOSS HEATING SOLUTIONS
MAKING MODERN LIVING POSSIBLE Danfoss Air Installation manual for duct systems DANFOSS HEATING SOLUTIONS Index 1 Before you start...........................................................................
More informationMiniature Steam Steam Plant Kit
Miniature Steam Pty Ltd. Bringing the Highest Quality Standards to Model Engineering Miniature Steam Steam Plant Kit for self assembly in Caldercra Marie Felling Harbour Tug Single Screw Op on with 3 Horizontal
More informationx:panda, size 1, med. back X c x:panda, size 1, med. seat 7¼" X c
Account No. Drop Ship: Date: Name P.O. Number: Address Buyer: City Marked For: State Zip E Mail: Tel. Fax Features included in standard price: Height, Depth & Angle Adjustable Back Angle Adjustable Adduction
More informationApplication Note. Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes
Application Note Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an HO Atlas RS-3. Skill Level
More informationMARACANA ASSEMBLY INSTRUCTION .40 ARF LOW WING TRAINER RADIO CONTROL MODEL. Every body can fly
RADIO CONTROL MODEL ASSEMBLY INSTRUCTION MARACANA.40 ARF LOW WING TRAINER Every body can fly VQA085 EP GP You can use both Gas or Electric power Wingspan: 59in.(1520mm) Fuselage length: 48in.(1220mm) Engine:
More informationSAN FELIPE: Step by Step Pack 8
Pack 8 Your parts Gun port frames Complete gun ports Tools and equipment Tweezers Superglue Pliers Hammer Sandpaper Wood stain Paintbrushes Black pen a Glue gun port frames to the gun ports of the main
More informationmagnum smoothwall Bins features & options QUALITY TOP TO BOTTOM Customer driven smoothwall solutions
SMOOTHWALL STORAGE magnum smoothwall Bins features & options QUALITY TOP TO BOTTOM No company has more experience manufacturing grain storage systems for both commercial and on-farm application than Westeel.
More information1660mm (65.4 in) 1200mm (47.2 in) 2700gr gr 6 channel - 7 servo standard 46/ 2 stroke or 52/ 4 stroke
Instruction Manual CESSNA-46 1660mm (65.4 in) 1200mm (47.2 in) 2700gr - 3000gr 6 channel - 7 servo standard 46/ 2 stroke or 52/ 4 stroke KIT CONTENTS: We have organized the parts as they come out of the
More informationSTANDARD ONDUFIL TM MULTI-TURN SPRING WASHER RANGE
per turn RD0223S320025IX 22.0 18.0 2.0 x 0.25 3.5 3 5.8 3.0 4.0 1.4 RD0223S420025IX 4 7.8 4.0 4.0 1.0 RD0223S520025IX 5 9.6 4.3 4.0 0.7 RD0223S620025IX 6 11.0 5.0 4.0 0.7 RD0223S720025IX 7 12.7 5.8 4.0
More informationEbErCool StAtIoNAry CoolINg SyStEmS
climate comfort I transporters, motor homes, CommErCIAl ANd SPECIAl VEhIClES EbErCool StAtIoNAry CoolINg SyStEmS ebercool A World of Comfort 2 ClImAtE Comfort EbErCool Climate Comfort ebercool 3 the right
More informationInstruction Manual book
book ITEM CODE:BH 115. SPECIFICATION Wingspan : 6,000 mm 236,22 in. Length : 2,740 mm 107,87 in. Weight : 17.5kg 38.5Lbs. Radio : 08 channels. Servo : 07-08 HS-5685MH(HITEC) Battery : 2 Cells-Li-Po 7.4V
More informationSHIPPING INFORMATION Provider Acct #: Address: ST: ZIP:
May 2014 Kids FAST Order Form Maximum Weight Capacity 80 lbs. 12"Wx14.5"Dx19.5"H Seating Capacity. Customer Service: 800-800-8586 (toll free) Email: orders@pridemobility.com Date: Quote Order SHIPPING
More informationASSEMBLY MANUAL. Graphics and specifications may change without notice.
NEMESISMS: SEA 111 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications Wing span------------------------------------- 55.9in ------------------------------- 142cm. Wing
More informationGuns & Missiles Symposium #11725
Guns & Missiles Symposium #11725 31st August 2011 13:35-1355 RM-ADM-IM05 C 40mm CTAS Medium calibre goes in a new direction David Leslie, Chairman CTA-International 22/09/2011 2 CTA-International CTA International
More informationMedical Treatment Chair. T688 Series How to use guide
Medical Treatment Chair T688 Series How to use guide Your T688 Medical Treatment Chair Fresenius Medical Care - The Renal Company - contributes to enhanced care in modern day treatment facilities by offering
More informationFelix Building Instructions Art. No
Felix Building Instructions Art. No. 20300 1. Assemble the boat stand from parts 1-2-3 as shown on the small plan. the deck in position. (See hull sections BB & CC for position.) For the following sequence
More informationRoll Bar (MMRB-6.1 to -6.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Roll Bar (MMRB-6.1 to -6.7) NOTE: These instructions cover Roll Bars with
More informationMS:176 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
ASSEMBLY MANUAL MS:176 Graphics and specifications may change without notice. Specifications: Wing span ------------------------------98.4in (250cm). Wing area ----------------1576.4sq.in (101.7sq dm).
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationYAK-54 EXP. 48 inch Electric ARF
YAK-54 EXP 48 inch Electric ARF 1 Greetings and congratulations on your purchase of the Extreme Flight RC Yak-54 EXP ARF! Like all of the EXP series, the YAK-54 excels at both 3D and precision maneuvers.
More informationInstallation or Inspection Checklist
Sequencing Batch Reactor Installation or Inspection Checklist Only modules bearing the NSF logo and designated PS1-XX are certified to NSF/ANSI Standards 40 and 245 2018 Anua 1-2018 Pre-installation and
More informationInstruction Manual. Wingspan : 2270mm (89.37 inches) : 1870mm (73.62 inches) : 7400gr gr. : 4 channel - 6 standard servo.
Wingspan : 2270mm (89.37 inches) g Length : 1870mm (73.62 inches) Weight : 7400gr - 7600gr Radio : 4 channel - 6 standard servo Engine : 25cc-35cc KIT CONTENTS: We have organized the parts as they come
More informationINSTRUCTIONS MOLAD - + Warning Laser Light. Optional Accessories
2 Harris Court, Suite A-4 Monterey, CA 93940 U.S.A. Tel: (831) 373-0701 Fax: (831) 373-0903 E-mail: Sales@laserdevices.com Internet: www.laserdevices.com Images and text copyrighted by Laser Devices, Inc.
More informationInstruction Manual. Wingspan : 1400mm (55.12 in) : 1370mm (53.94 in) : 2600gr gr. : 4 channel / 5 servo. : / 2 stroke_52-71 / 4 stroke
Instruction Manual 540 Wingspan : 1400mm (55.12 in) g Length : 1370mm (53.94 in) Weight : 2600gr - 2800gr Radio : 4 channel / 5 servo Engine : 46-52 / 2 stroke_52-71 / 4 stroke KIT CONTENTS: We have organized
More informationMulti Bari. Key features at a glance: Additional options:
Multi Bari 2 Multi Bari Designed for comfort and pressure management control, the Multi Bari has removable waterfall back cushions that can be individually positioned and re-positioned for comfort with
More informationMiG-29 Retract Kit (for the HET-RC Mini Air Retract System)
MiG-29 Retract Kit (for the HET-RC Mini Air Retract System) The MiG-29 Retract Kit was designed to allow the easy installation of the HET-RC mini Air Retract system into the twin EDF MiG-29. We recommend
More informationMS:159 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
ASSEMBLY MANUAL MS:159 Graphics and specifications may change without notice. Specifications: Wing span ----------------------------61.8in (157cm). Wing area -----------------1100.5sq.in (71.0sq dm). Weight
More informationDrag Race Roll Bar (MMRB-6, -7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Drag Race Roll Bar (MMRB-6, -7) The Maximum Motorsports 6-point Drag Race
More informationSETUP & DAILY USE INSTRUCTIONS
TM easycomposites share the knowledge SETUP & DAILY USE INSTRUCTIONS Composites Vacuum Pump VP425 VP3400 1 CONTENTS 1. Introduction 2 2. First Time Use - Setup Instructions 3 1. Fill pump with oil 3 2.
More informationDK043/DK043H Rhino-Rack VA, Aero, Euro & HD crossbar instruction
DK043/DK043H Rhino-Rack, ero, Euro & crossbar instruction IDENTIFICTION CHRT crossbar crossbar crossbar crossbar CROSSBR CROSSBR Ford Laser 5dr Hatch 03/99-08/02 187mm 132mm 942mm / 37,2/32 173mm 118mm
More informationUser Guide. Always abide by this User Guide
User Guide This User Guide and all the safety instructions must be read and adhered to before use of the StrideOn. For questions, please contact the place of purchase/rental or call StrideOn Australia
More informationRVJET Flying wing specially designed for FPV. RangeVideo Wireless Video Solutions
RVJET Flying wing specially designed for FPV Features: Durable EPO in black or white Variable wing span 1.55m/1.95m Compact during transport (original packing can be used) Specially designed for RVOSD
More informationAssembly and operating instructions. Assembly and Operating Manual
Assembly and operating instructions Assembly and Operating Manual Dear customer, Assembly and Operating Manual The radio control system Glued joints, suitable adhesives Congratulations on your choice of
More informationWING ASSEMBLY SECTION 13 INSTALLING FUEL TANKS AND RIVETING THE WING SKINS CLOSED
WING ASSEMBLY SECTION 13 INSTALLING FUEL TANKS AND RIVETING THE WING SKINS CLOSED Compass Check 1. Measure the location of the tank outlets. 2. Install supports. 3. Cut the holes in the skin and ribs for
More informationEtac presents: The Clean family A cleaner Clean
Etac presents: The Clean family A cleaner Clean Discover the Clean family For almost 20 years, Etac Clean has been a best-selling mobile shower commode chair. There have been copies and imitators, but
More informationYAK54 MK2. GP/EP size.120/20cc SCALE 1:4 ¾ ARF. Instruction Manual. version. version
Instruction Manual GP EP version version GP/EP size.10/0cc SCALE 1:4 ¾ ARF SPECIFICATION - Wingspan: 168 (66.3 in) - Length: 1605mm (63.1 in) - Flying weight: 4700-500 gr - Wing area: 54.7 dm - Wing loading:
More informationand excellence Effectiviness XA-series Armoured Wheeled Vehicle Family
XA-series Armoured Wheeled Vehicle Family Patria Vehicles Oy P.O. Box 186 FIN-13101 Hämeenlinna Finland Tel. +358 3 6451 Fax +358 3 619 6710 vehicles@patria.fi www.patria.fi From 1st January 2003: Tel.
More informationGent EPP. Before use please read the explanations carefully
Before use please read the explanations carefully Gent EPP Instruction Manual Specifications Fuselage length 900mm 35in Wingspan 820mm 32in Flying Weight 210 240g with battery Additional Required Equipment
More informationJUNKERS CL1 G-BUYU. Specifications: Code: SEA275. Graphics and specifications may change without notice. ASSEMBLY MANUAL
ASSEMBLY MANUAL JUNKERS CL1 G-BUYU Code: SEA275 Graphics and specifications may change without notice. Specifications: Wingspan---------------68.9 in (175 cm). Wing area---------------776.6 sq.in ( 50.1
More informationWW03e Welcome Wagons 8 Shoe Brake Pipe Wagon
WW03e Welcome Wagons 8 Shoe Brake Pipe Wagon History The pipe wagons were built to four basic diagrams sharing the same basic dimensions. The first 300 pipe wagons were built at Derby works to diagram
More informationInstructions: Pullman-Standard PS-3 Coal Hopper Kit Tangent Part Numbers: through /2015
Instructions: Pullman-Standard PS-3 Coal Hopper Kit Tangent Part Numbers: 15000-01 through 15001-01 10/2015 Thank you for purchasing the Tangent Scale Models Pullman-Standard PS-3 Coal Hopper Kit! A few
More information5.SS Wiking Panthers
5.SS Wiking Panthers a Tom Wise Painting Guide Originally posted on the Flames of War forums, July 18, 2010 as GBX19 Panther A, 5th SS Wiking Painting and Assembly Guide Miniatures shown are products of
More informationAll pictures show trays relative to a standard sized KR Multicase (1 KRU), 1 standard KR Unit Pre-selected Sets (Custom) WH40K-SM-C
All pictures show trays relative to a standard sized KR Multicase (), 1 standard KR Unit Pre-selected Sets (Custom) WH40K-SM-A WH40K-SM-B WH40K-SM-C WH40K-SM-D WH40K-SM-E Space Marines Set A 2x Rhino/
More informationRoughRider. Rider Measurements. Select Wheelchair Size Options
For more information on specifications and fitting of the RoughRider wheelchair see www.whirlwindwheelchair.org/roughrider Rider Name Rider Age Rider Gender Rider Reference # Rider contact information
More informationBEFORE YOU BEGIN, GET YOUR TOOLS READY BRUSH THE HARDWARE LISTED BELOW IS INCLUDED IN THIS KIT SPRING, VALVES (16) 3/16" X 13/32" COILED SPRINGS
KIT 8883 8588833001 VISIBLE V-8 ENGINE BEFORE YOU BEGIN, GET YOUR TOOLS READY IDENTIFICATION ON TAB ON RUNNER KNIFE FILE BRUSH TOOTHPICK TAPE CLOTHES PIN ON PART TWEEZERS BRUSH RUBBER BAND REMOVE PART
More informationASSEMBLY MANUAL. Kit features. MS:76
ASSEMBLY MANUAL MS:76 Graphics and specfications may change without notice. Specifications: Wingspan---------------------------------------------------- 82.8 in------------------------------------- 210.3cm.
More informationInstruction Manual book
book SPECIFICATION Wingspan : 2,080 mm 81.89 in. Length : 1,680 mm 66.14 in. Weight : 6.2 kg 13.64 Lbs. Radio : 06 channels. Servo : 06 servos. Engine : 30-35 CC Gas(FUJI IMVAC). Made in Vietnam. This
More informationPAULISTINHA P-56. Requires: cu. in. displacement 2-stroke cu. in. displacement 4-stroke 4 - channel radio w/ 5 standard servos
INSTRUCTION MANUAL PAULISTINHA P-56 Requires: 0.0-0.6 cu. in. displacement -stroke 0.5-0.56 cu. in. displacement -stroke - channel radio w/ 5 standard servos Wing Span Wing Area Flying Weight Fuselage
More informationTRIMLINE CARTRIDGE FILTERS
TRIMLINE CARTRIDGE FILTERS Owners Manual! WARNING This equipment must be installed and serviced by a qualified technician. Improper installation can create electrical hazards which could result in property
More informationMS:183 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
MS:183 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------79.9in (203cm). Wing area -----------------1165.6sq.in (75.2sq dm).
More informationPart 11: Wheelchairs. Test dummies
INTERNATIONAL STANDARD ISO 7176-11 Second edition 2012-12-01 Wheelchairs Part 11: Test dummies Fauteuils roulants Partie 11: Mannequins d essai Reference number ISO 2012 COPYRIGHT PROTECTED DOCUMENT ISO
More informationFigure 3-1. MK 67 MOD 7 gun cradle.
CHAPTER 3 GROUND AND VEHICLE MOUNTS The MK 19 is used in either the ground- or vehicle-mount mode. The most often used ground mount is the M3 tripod. The M3 serves as a stable platform when the weapon
More informationWARNING. ARB 4x4 ACCESSORIES. Corporate Head Office Garden St Tel: +61 (3) Kilsyth, Victoria Fax: +61 (3) AUSTRALIA 3137
Part Numbers: Suited to vehicle/s: 3212400 - ARB BULL BAR NON-FLARED 3212410 - ARB BULL BAR FLARED 3412400 - ARB WINCH BAR NON-FLARED* 3412408 - ARB WINCH BAR NON-FLARED (EXPORT ONLY)* 3412410 - ARB WINCH
More information