CONTROL PANEL PARTS. Part # Description Qty. Part # Description Qty Momentary Switch Push Button Guard 1.

Transcription

1 CONTROL PANEL PARTS MAGNET 7 A M P MOTOR PRESS-ON OFF / ON RELEASE- OFF AUS BLACK POWER WHITE POWER MOTOR WHITE MOTOR BLACK Description Qty Push Button Guard Nut Nylon Slotted Switch Seal Green Rocker Switch Circuit Breaker 3 Amp Power Cord Aus Model BHC Screw # Description Qty Momentary Switch Nut Rectifi er Assy Jumper Wire Circuit Breaker 7A Power Cord Cover w/ Label 1 7

2 HMD111 DRILL PARTS DIAGRAM

3 HMD111 PARTS LIST Item # Description Qty Motor Assy Gear Cap Asy Housing Assy Magnet Assy Electrical Box Control Panel Assy Control Panel (AUS) OD Spiral Lock Thurst Washer Bronze Thrust Washer Steel Arbor Assy FHS Screw 1/ Quill Assy Ball Bearing Washer, Bearing Ret FHC Screw Key Splined Shaft SHC Screw 1/ SHC Screw M SHC Screw M BHS # Ground Label BHC Screw # Feed Handle Assy Feed Gear Snap Ring SHC Screw # Left Hand Gear Right Hand Spiral Miter Gear Thrust Bearing Thrust Washer Spring Plunger (Not Shown) Lock Washer Thrust Washer Shield Thrust Washer Thrust Needle Bearing Spring Plunger Plunger Flat Head Screw Mod. 1 Part No (Arbor/Quill Assy) Includes: 7, 9, 10, 11, 13, 35, 36, 37 Rotaloc Cutters for HMD111 The Rotaloc Annular cutters are made specifi cally for the HMD111. They are equipped with 5/8 tool-less quick release shank, and can drill up to 3/4 deep in single or stacked plate. They are made of premium high speed steel and available in diameters from 1/2 (12mm) to 1-1/16 (27mm). Rotaloc Cutter Kit - Hougen part number Kit includes all 10 cutters listed plus 2 pilots all in a handy case / / / / / / / / /16 Rotaloc Cutters mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm 9

4 Motor Diagram and Parts List Item # Description Qty Motor Assy Field case Gear Housing Cover Ball Bearing Ball Bearing Ball Bearing Ball Bearing Dust Seal st Inter. Gear Assy nd Inter. Gear Assy Spur Gear Flat Washer Key Dowel Pin 1 Item # Description Qty Gear Housing Spindle Fan Guide Gasket Armature Field Carbon Brush Brush Cap Pan Head Screw (Field) Pan Head Screw (Short) Pan Head Screw (Long) Retaining Ring Retaining Ring Paper Washer Flat Washer 1 10

5 Wiring Diagram Power In To Motor Power In White To Magnet Yellow To Motor White Hougen Manufacturing, Incorporated warrants its Portable Magnetic Drills, Electro-hydraulic Hole Punchers, and Tornado II Paint Shaker for one (1) year and other products for ninety (90) days from date of purchase against defects due to faulty material or workmanship and will repair or replace (at its option) without charge any items returned. This warranty is void if the item has been damaged by accident or unreasonable use, neglect, improper service, or other causes not arising out of defects in material or workmanship. No other expressed warranty is given or authorized. Hougen Manufacturing, Inc. disclaims any implied warranty of MERCHANTABILITY or FITNESS for any period beyond the expressed warranty and shall not be liable for incidental or consequential damages. Some states do not allow exclusions of incidental or consequential damages or limitation on how long an implied warranty lasts and, if the law of such a state governs your purchase, the above exclusion and limitation may not apply to you. This warranty gives you specifi c legal rights and you may also have other rights which vary from state to state. To obtain warranty service, return the item(s), transportation prepaid, to your nearest Factory Authorized Repair Center or to Hougen Manufacturing, Inc., 3001 Hougen Drive, Swartz Creek, Michigan Hougen Drills (Hougen Cutters) are warranted against manufacturing defects only. Subject to Hougen Manufacturing inspection. THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PAR- TICULAR PURPOSE Hougen Manufacturing, Inc. Commercial / Industrial Limited Warranty HOUGEN PATENT NOTICE The products in this manual may be covered by one or more of the following U.S. patents, foreign patents, and pending patents: D Photographs and Specifi cations shown are accurate in detail at time of printing. Manufacture reserves the right to make improvements and modifi cations without prior notice. Hougen, Trak-Star, and Punch Pro are proprietary trademarks of Hougen Manufacturing Inc. Ogura and the Ogura logo are proprietary trademarks of Ogura & Co., Ltd. Vac-Pad is a propriety trademarks of Drillmate PTY, Ltd. 11