T Pulse. T /DL Pulse, with Dallas reader. T /R Pulse, with rotation kit

Transcription

1 T Pulse T /DL Pulse, with Dallas reader T /R Pulse, with rotation kit T /DL/R Pulse, with Dallas reader and rotation kit M O U N T I N G I N S T R U C T I O N S

2 DIMENSIONS The terminal for the electronic key (Dallas Key) is located in the front, over the keypad (only models T6530/DL and T6530/DL/R). AS TURNABLE ENTRY UNIT (only for models T6530/R and T6530/DL/R) The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The hole must be deburred well to avoid damage to the cable. II_T6530_02_eng Page 2 of 8

3 Cut the grooved shaft to the appropriate length: Measure door thickness (from mounting surface of the entry unit to the mounting surface of the lock) and add 40 mm (1.6 ). The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The hole must be deburred well to avoid damage to the cable. Prepare the mounting and cable holes according to picture 1. Hold the bearing plate in a way against the mounting surface that UP ROTATE is readable on top (picture 2). Affix the bearing with the two mounting adapter (M4 do not over tighten). Insert first the spring and then the pin into the hole on the back cover (picture 3). Insert the grooved shaft, with the cutting edge first, all the way into the entry housing (picture 4). Now push the cable into the groove until flat over the entire length of the shaft. Route the cable and shaft through the spindle hole of the door, hold the unit at an approximately 10:00 o clock position, and slide it on the mounting adapters (picture 5). Turn unit clockwise until it clicks into straight position at 12:00. Remove adhesive film from pad and line up margins carefully, before fixing it. Connect one (1) battery to the battery clip. Only use 9V- ALKALINE batteries from brand name manufacturers like DURACELL. STATIONARY MOUNTING (only for models T6530 and T6530/DL) The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The hole must be deburred well to avoid damage to the cable. Lift the pad so that you can see mounting holes. Let lock s connecting cable pass through the hole on safe s door. Insert and fix the two screws, paying attention to cables, they have not to be squashed by housing and let battery cables have easy access. Remove adhesive film from pad and line up margins carefully, before fixing it. II_T6530_02_eng Page 3 of 8

4 Connect one (1) battery to the battery clip. Only use 9V-ALKALINE batteries from brand name manufacturers like DURACELL. ROTOBOLT DIMENSIONS: BOLTWORK REQUIREMENTS and MOUNTING INSTRUCTION In the LOCKED position, there should be approximately 1 mm clearance between the lock bolt and the cavity in the blocking bar of the boltwork. The lock bolt must move freely into the cavity. Only use TECNOSICUREZZA supplied screws to mount the lock. Tighten the screws securely so the lock body is attached firmly to the mounting surface. Do not overtorque mounting screws (Torque approximately 3,5 Nm). Insert the connector of the entry unit in the outer position ENT. Check that the connector is completely seated (To remove the connector, lift it up and carefully pull it out). In the entry unit or battery box, connect a 9V-ALKALINE-battery from a brand name manufacturer, e.g. DURACELL. II_T6530_02_eng Page 4 of 8

5 STRAIGHTBOLT DIMENSIONS: BOLTWORK REQUIREMENTS and MOUNTING INSTRUCTION In the LOCKED position, there should be approximately 1 mm clearance between the lock bolt and the cavity in the blocking bar of the boltwork. The lock bolt must move freely into the cavity. In OPEN position, there should be approximately 5 mm clearance between the lock bolt and the bloching bar of the boltwork. Do not overtorque mounting screws. The grooved shaft must extend between 10 and 15 mm off the mounting surface. Make sure the cable is in the groove. II_T6530_02_eng Page 5 of 8

6 Insert the cable connector into the square hole in the bottom of the lock and guide it through the hole in the lock cover. Insert the connector of the entry unit in the outer position. Check that the connector is completely seated. (To remove the connector, lift it up and carefully pull it out.) FUNCTIONAL TEST (with door open) A. Test Electronics Press and hold [5] until a double signal sounds and the light stays ON. Enter the all keys in exactly this sequence: [1]-[2]-[3]-[4]-[5]-[6]-[7]-[8]-[9]-[0] Push buttons slowly so you recognize the signaling of the lock. A double signal indicates that the keypad and the lock communicate properly. A long signal indicates that the electronics may be damaged. B. Mechanical Test Enter code (1,2,3,4,5,6). The lock emits a double signal for the correct code. Turn Entry unit clockwise until stop. Lock bolt must move freely. Boltwork/door can be opened. Move boltwork into Locked Position. Lock bolt must fully extend and secure. IMPORTANT: Perform the functional test several times before locking the safe door. II_T6530_02_eng Page 6 of 8

7 Before operating the lock, please read this manual thoroughly, and retain it for future reference. Correct disposal of this product: (Waste Electrical & Electronic Equipment) Applicable in the European Union and other European countries with separate collection systems. This marking displayed on the product or its literature indicates that it should not be disposed with other wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. II_Pulse_00_eng Pagina 7 di 8

8 TECNOSICUREZZA s.r.l. Via Cesare Battisti, S. Giovanni Lupatoto (VR) - Italy Tel Fax info@tecnosicurezza.it -