Fanatec Universal Hub conversion guide. January 2018
|
|
- Spencer Jennings
- 5 years ago
- Views:
Transcription
1 Fanatec Universal Hub conversion guide January 2018 This guide will show you how to fit our Fanatec conversion kit to the Universal Hub. The hub we are using was purchased in November Older versions have some differences which we will try and describe as we go through the conversion steps. Our Universal hub also has our snap action shifter add on which is why the shiffters look different. Step 1 Open up the Hub by removing the 4 bolts shown
2 Step 2 Remove all of the button and shifter connectors so that the inside PCB is clear of wires Also remove the little display
3 Step 3 Remove the PCB Start by removing the 4 screws holding the PCB in place Now slide the PCB down towards the USB plug. Newer versions of the Universal hub will allow you to just lift out the PCB together with the top button PCB, leaving the rubber buttons in place. Older versions have the rubber buttons attached to the PCB and so you have to gently ease it out including the buttons. Pushing the buttons in from the top as they move helps just take your time. Be very careful not to break the LED and long stick button.
4 The PCB will come out of the caseing and just be held on by the QR cable. Most versions have glue holding the QR cable plug in place. This can either be softened with a hair dryer or I prefer to just pull it off. However you remove it be very careful and gentle do not pull too hard otherwise the hole socket will come off the PCB. I tend to use my fingernail or a set of blunt plyers and make small twisting motions to pemove the glue in small piees. You can now remove the Fanatec QR by undoing the 6 bolts and pulling the cable and plug through the centre hole. You should now have everything disconnected and are ready to start installing the conversion kit.
5
6 Step 4 Take the conversion kit as shown the SRM logo is at the top. Pass the cables through the centre hole in the Universal Hub casing. NOTE: If using the AccuForce QR it must be fitted to the conversion kit before fitting the kit to the Hub. Use the 3 supplied bolts to fit the conversion kit to the Universal Hub. We recommend using a little threadlock to prevent them working loose over time.
7 There are 2 sets of wires from the kit. One has a round connector on it. This is a grounding wire which although not normally needed, helps prevent any EMI issues. Take one of the short bolts you removed from the Fanatec QR and use that to fit the ground wire to the top hole. This hole is slightly off as it s designed for 50mm QR s on the other side so it will take a bit more effort to get it to tighten this is good though because it ensures the good grounding connection. Next we need to connect the plug from the kit into the Universal Hub PCB. I supply two different methods for this. Sometimes the kit will have a 13pin plug on it s end, in this case you simply slot that directly into the PCB socket. If you have an 8 pin plug then you should have ordered the Universal Hub cable. This converts the 8 pin to the 13 pin used by the Universal Hub. The other Fanatec CSW wheels us the 8 pin plug. The plug should have the raised part at the top and just slides easily into the socket. You can apply some hot glue if you wish to hold it in place more firmly, but it should not move without. The kit is now applied to the Universal hub.
8 Step 5 Now just reverse the steps for removing the PCB and reassemble the Hub. Take care not to get the kit wires caught under the PCB screws as they will be crushed and damaged when you tighten the screws. If using the older version of the Hub remember to very gently get the top, rubber buttons back into place and again take great care not to damage the long button and LED. Should should now be ready to go. Fit your QR to the kit Plug in the USB cable The buttons will be seen by windows and do not need any software. To use the display you can use the free Fanaleds software.
Conversion PCB Installation Instructions
ClubSport Porsche 918 RSR Wheel Conversion PCB Installation Instructions Thank you for the purchase of the Fanatec Standalone Conversion PCB, this guide will talk you through the installation of the PCB
More informationFanatec GT3RS V1 to GT3RS V2 Tutorial
Fanatec GT3RS V1 to GT3RS V2 Tutorial by Roy Visser 1 How to update your Fanatec GT3RS V1 wheel to a GT3RS V2 wheel Welcome to this guided and detailed tutorial for upgrading your Fanatec GT3RS V1 wheel
More informationHornby Railroad Hall EM Finescale Conversion.
Hornby Railroad Hall EM Finescale Conversion. The subject of this sheet is the new (2015) Hornby Railroad Hall. There are several specification and livery variants, but all have a common chassis and as
More informationBachmann GWR Earl (Dukedog) EM Finescale Conversion
Bachmann GWR Earl (Dukedog) EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better
More informationVTCM Installation Manual Table of Contents
VTCM Installation Manual Table of Contents 1. Introduction:... 2 2. Disclaimer:... 2 3. Software / Drivers:... 2 a. Plugging in the controller:... 2 b. Install 4.0.NET Frame work:... 3 c. Install COM port
More informationHornby GWR Star Class EM Finescale Conversion.
Hornby GWR Star Class EM Finescale Conversion. Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than
More informationSIM RIG GT. Product Manual
SIM RIG GT Product Manual Introduction Thank you for purchasing the Heusinkveld Engineering Sim Rig GT! This is a compact, clean, adjustable and very stiff simulator frame for a GT-style simracing experience.
More informationHeljan EM Finescale Conversion.
Heljan 02 2-8-0 EM Finescale Conversion. Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SPEED CABLE SHIFTER units built before 4/30/12
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 6 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2"-
More informationSteeda Billet Charge Motion Control Plates (05-08 GT) - Installation Instructions
Steeda Billet Charge Motion Control Plates (05-08 GT) - Installation Instructions The below installation instructions work for the following products: Steeda Billet Charge Motion Control Plates (05-08
More informationBachmann D11 EM/S4 Finescale Conversion
Bachmann D11 EM/S4 Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationWritten By: Jeff Suovanen
iphone 6s Display Assembly Replacement Replace the entire display assembly on your iphone 6s. Written By: Jeff Suovanen ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide if your
More information1. Invert the tender, and hold in a suitable device. We use a foam cradle the Peco loco service cradle being ideal.
Bachmann J11 EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationGuide to fitting a MK2.5 (Facelift) Centre Console into a MK2 Focus. The Parts
Guide to fitting a MK2.5 (Facelift) Centre Console into a MK2 Focus For the latest project on my MK2 Focus I decided that a Facelift centre console would tie my previous interior uplift together. As I
More informationMikuni RS Carburetor Conversion
Mikuni RS Carburetor Conversion After putting your carbies on the bench or the kitchen table if the wife is out, you will see that the linkages may be in different positions depending on which brand of
More informationArrow Shark 2016 M8 II Sterndrive - Collector Edition Owner Manual. M8 II weight: 925 grams Dimensions
Arrow Shark 2016 M8 II Sterndrive - Collector Edition Owner Manual M8 II weight: 925 grams Dimensions Parts List M8V2#0001 Billet Lower Unit M8V2#0013 Steering Cable Assembly M8V2#0002 Steering Arm Housing
More informationG&G GR14 Airsoft Reassembly
G&G GR14 Airsoft Reassembly This Guide will show you the right technique for proper and fast assembly. Written By: 101 Tech USA ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION The G&G m-14
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More informationM14 AUTOMOTIVE SPARK PLUGS AND WIRES CONVERSION KIT INSTALLATION INSTRUCTIONS
M14 AUTOMOTIVE SPARK PLUGS AND WIRES CONVERSION KIT INSTALLATION INSTRUCTIONS (It is highly recommended you read the instructions completely before beginning) 1. Be sure the magneto switches are turned
More informationKodak 750H Carousel Projector Repair
Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, 3-26-2016 Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors
More informationRS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.
RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR 2007-2016 JEEP WRANGLER ALL MODELS. Rear Bumper Installation Instructions 1) Remove factory rear bumper, (this includes all tow hitch
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SPEED CABLE SHIFTER units built before 4/30/12
Paso Robles, CA 93447 PAGE 1 OF 6 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302075
More informationTutorial:Head Unit Installation
Tutorial:Head Unit Installation From Tech Wiki : Nissan 350Z : Infiniti G35 : Nissan GT-R Here, I installed the Kenwood DDX7015 touch screen DVD system. I made this step-by-step tutorial to help those
More informationRe-Energy.ca - Solar Electricity - Build Your Own Solar Car
Backgrounder Build Your Own Solar Car Back to Page 1 Build It! These step-by-step instructions provide you with a plan for making a basic solar car. If you can think of ways to improve the design of your
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationWritten By: Andrew Optimus Goldberg
Remove the logic board from your iphone 5 Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Resurrect your iphone 5 with a new logic board. TOOLS: P2 Pentalobe
More informationWritten By: Evan Noronha
iphone 6s Battery Replacement Replace the battery in an iphone 6s. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Use this guide to bring life back to your iphone
More informationTOYOTA SUPRA JZA80 HEADLIGHT LENS TUTORIAL
TOYOTA SUPRA JZA80 HEADLIGHT LENS TUTORIAL Disclaimer: Original Motorsports takes no responsibility for any errors which may occur in your DIY project. This is simply a guide. If you are not confident
More informationPYRTE. Building The Front Axle, Fork and Steering
PYRTE Building The Front Axle, Fork and Steering The front axle on this traction engine is a very simple affair, in that it is a rectangular steel rod, sat on edge, with a pivot in the centre, which is
More informationCHAPTER 11: FLYWHEEL, CLUTCH AND ALTERNATOR BACK ON
CHAPTER 11: FLYWHEEL, CLUTCH AND ALTERNATOR BACK ON Posted on the Wildguzzi forum by Pete Roper: January 17, 2006: Contents: Assembling the engine. Flywheel, clutch and alternator back on. Pic 11-1: To
More informationREAR INTERIOR AMBIENT LED FITTING INSTRUCTIONS AUDI A4(B6) 2001 onwards
GLUE is required to secure the supplied lighting module into place, and is not included as part of this modification kit. Please read the instructions fully before commencing this modification. NOTE: Ensure
More informationHornby Railroad Crosti 9F EM Finescale Conversion.
Hornby Railroad Crosti 9F EM Finescale Conversion. Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better
More informationS1 Sequential. T56 Magnum. Sequential shifter. Contents and assembly instructions
S1 Sequential Sequential shifter T56 Magnum Contents and assembly instructions Parts List Sequential shifter x1 Base plate x1 Base spacer x1 Drill Square x1 Shaft fitting x1 Square washer x1 8mm Aluminium
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More information1. Get fork mounted in stand. You can leave it in the bike, but you must remove the wheel and front brake.
Tools Needed: Bike stand Lint free shop Towels 1.5mm Allen Key Pick Set Grease (We recommend Slick Honey) Oil Measuring Cup (with cc Scale) Small Metal Drift Shop Vise Oil Bucket 13mm Deep Socket (6 point)
More informationRear Speaker replacement.
Rear Speaker replacement. First off you need the right rear speakers. The easy bit is 6x9 and better than a 15W paper cone, the difficult bit is getting a mounting depth under 74mm. Or to be more precise,
More informationTL4076 Top 5 Tips Get to know your TL4076
TL4076 Top 5 Tips Get to know your TL4076 Thermal Break with Teflon liner (behind fan) Hot End Assembly Fan Heat Block Extruder with toothed gear(brass) and idler (steel) Filament Guide Tube Nozzle Cable
More information10A 10F 10B 10E 10A 10D 10B. Mr. T 10C Q R
Q R 2 0 23 30 12 18 17 16 15 14 37 39 38 3 7 6 5 20 26 21 22 40 13 4 2 25 24 8 1 28 27 11 31 19 10A 10D 10B 10C 10 29 10A 10F 10B 10E 10 9 32 36 33 34 35 178 15 GENERAL 82 80 Ø28.6 ±0.1 Ø30 +0.05 0 348
More informationINSTRUCTIONS FOR INSTRUCTIONS FOR USE USE Bambino panthera panthera
INSTRUCTIONS FOR USE Bambino panthera Contents Intended use s 2 Adaptation s 3 Maintenance s 8 Safety s 9 Crash test s 11 Intended use The Panthera Bambino wheelchair is designed for children who need
More informationWritten By: Sam Lionheart
iphone 6 LCD Shield Plate Replacement Replace the LCD shield plate in an iphone 6. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION Use this guide to remove or replace
More informationGearbox Assembly 101. Introduction. Before Beginning. By Mark Schutzer 4/13/06
Gearbox Assembly 101 By Mark Schutzer 4/13/06 Introduction If you are planning to re-motor an old brass locomotive you may want to upgrade to a new gearbox at the same time. The early 60 s and 70 s gearboxes
More informationINSTALLATION & OPERATION INSTRUCTIONS COMFORT RIDE HITCHES (CRH) MODEL 214 AND MODEL 308
INSTALLATION & OPERATION INSTRUCTIONS COMFORT RIDE HITCHES (CRH) MODEL 214 AND MODEL 308 Installation This hitch is designed to be installed into standard slotted rails such as the Reese, Valley, etc.
More informationMustang One-Touch Convertible Top Module (2005+) - Installation Instructions
Mustang One-Touch Convertible Top Module (2005+) - Installation Instructions The below installation instructions work for the following products: Mustang One-Touch Convertible Top Module (2005+) Please
More informationipod Touch 5th Generation Display Assembly Replacement
ipod Touch 5th Generation Display Assembly Replacement Remove the display assembly from your ipod Touch 5th Generation. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23
More informationThis guide will explain how to remove the old springs from the car and replace them with lowering springs.
fubar Guide: Fitting lowering springs to the Mk2 Clio The method described below worked for me. I am not saying it is the only method to complete the task. I will not accept any responsibility for damage
More informationWritten By: Sam Lionheart
iphone 5s Volume Controls Replacement Replace the volume buttons and ringer switch in your iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide
More informationHornby 08 Diesel Shunter EM Finescale Conversion.
Hornby 08 Diesel Shunter EM Finescale Conversion. Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better
More informationiphone 5s Upper Component Cable Replacement
iphone 5s Upper Component Cable Replacement Use this guide to replace the upper component cable containing the flash, microphone and sleep/power button cable. Written By: Sam Lionheart ifixit CC BY-NC-SA
More informationBachmann 1F (Half Cab) EM Finescale Conversion
Bachmann 1F (Half Cab) EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than
More informationWritten By: Sam Lionheart
iphone SE Battery Replacement Replace the battery in your iphone SE. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 INTRODUCTION Use this guide to bring life back to an iphone
More informationLUGGAGE RACK MG TD with Original Steel Wheels. Installation Instructions. Step 1
Created on 7/7/2003 8:34:00 PM by Michael Grant Last Revised 2/2/2008 1:55:00 PM Page 1 of 14 1 2 3 243-705 LUGGAGE RACK MG TD with Original Steel Wheels If your TD has been converted to wire wheels, please
More informationForge Motorsport BMW N54 Diverter Valves
Forge Motorsport BMW N54 Diverter Valves Please thoroughly read through and familiarize yourself with these instructions in their entirety prior to beginning any part of the installation process of any
More information*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.
www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not
More informationLockpicking Tools: User Guide
Lockpicking Tools: User Guide Tips & Tricks for using Lockpicking Tools Contents Introduction..3 Padlock Shims..5 Comb Picks....7 Jiggler Keys...9 The Lock Gun..11 Bypass Sheets....13 Bump Keys...14 Other
More informationMacBook Pro 15" Unibody Late 2008 and Early 2009 Display Data Cable Replacement
MacBook Pro 15" Unibody Late 2008 and Early 2009 Display Data Cable Replacement Replace the display data cable in you MacBook Pro 15" Unibody Late 2008 and Early 2009. Written By: Walter Galan ifixit CC
More informationWritten By: Paige Reisman
iphone 7 Battery Replacement Replace the battery in an iphone 7. Written By: Paige Reisman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide to bring life back to your iphone 7
More informationQuad shift seal installation tips
Quad shift seal installation tips Rev. B Effective: 31-DEC-2015 Unobtainium Supply Co. 523 Longley Rd Groton, MA 01450 978.448.2110 www.unobtainiumsupply.com Quad shift seal installation tips TIP#1: BREAK
More informationHub Kit Fitting Guide 2016
Hub Kit Fitting Guide 2016 Important: For your own safety you must read this manual before attempting to fit any part of the motor kit to your bike. You must also ensure that you fit the kit in strict
More informationThere is hence three things you can do - add oil, adjust the temp that the clutch begins to engage, or do both.
As most of you may be aware, I have been doing a lot of research lately on our cooling system in the 80's including the fact that we have a dead spot on the OEM temp gauge which prompted me to not rely
More informationMotorola Moto Z Force Droid Battery
Motorola Moto Z Force Droid Battery Replacement Replace a dead or faulty battery in the Motorola Moto Z Force Droid. Written By: Kenji Fong ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION Use
More informationADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12
Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD
More informationO ring installation guide
AtomicRice.com O ring installation guide Tools and materials needed: 1) Phillips Screwdriver ( one medium and one large head) 2) Small or Medium sized flathead screwdriver or thin rigid shim 3) Vaseline
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationMID-MOTOR EBIKE KITS: INFORMATION FOR INSTALLERS
MID-MOTOR EBIKE KITS: INFORMATION FOR INSTALLERS Tips for evaluating bikes for conversion Consider the age, condition and value of the bike. Is it worthwhile using it as a donor? For reference, a good
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationFlexJet Carriage Circuit Board (PCB) Replacement
P/N: 111484 R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 ioline.com FlexJet Carriage Circuit Board (PCB) Replacement Notices: Warning! Ensure that all AC power cables
More information3D PRINTER. Pack 09. Anything you can imagine, you can make! 3D technology is now available for you at home! BUILD YOUR OWN
BUILD YOUR OWN Pack 09 Anything you can imagine, you can make! 3D PRINTER Compatible with Windows 7 & 8 Mac OS X 3D technology is now available for you at home! www.model-space.com BUILD YOUR OWN 3D PRINTER
More informationTri-Spark Ignition System Installation Triple Cylinder TRI-0001
Tri-Spark Ignition System Installation Triple Cylinder TRI-0001 There are potentially lethal high voltages produced at the ignition coils and spark plugs, therefore every precaution must be taken to prevent
More informationArrow Shark TS760-Marine Onboard E-Starter. Owner Manual
Arrow Shark TS760-Marine Onboard E-Starter Owner Manual The TS760-Marine Onboard E-Starter has concluded years of experience Arrow Shark has on RC boat onboard E-Starter, it will work for about all brands
More informationBehringerMods.com. Instructions for modification of Behringer DCX analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer DCX analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationSuper T QR20 INSTRUCTIONS GENERAL RULES
INSTRUCTIONS GENERAL RULES 1. Where specified, assemble and disassemble the shock absorption system using the MARZOCCHI special tools only. 2. On reassembling the suspension system, always use new seals.
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SP.
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X
More informationBMW E61 Hydraulic Pump replacement instructions
BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part
More informationCLUTCH CABLE REPLACEMENT GUIDE FOR THE FOLLOWING PRODUCTS 2004 ONWARDS
1 Issue 2 CLUTCH CABLE REPLACEMENT GUIDE FOR THE FOLLOWING PRODUCTS 2004 ONWARDS Mountfield 460R PD Briggs & Stratton Sprint Engine. Mountfield 460R PD/ES Briggs & Stratton Quantum Engine. Mountfield 460R
More informationPORTAGAUGE 4 USER MANUAL
PORTAGAUGE 4 USER MANUAL Contents 1. Introduction and Key Features 1.1 What does the Portagauge do? 1.2 The Portagauge 4 1.21 The Portagauge 4 Unit and Measuring Screen 1.22 The Portagauge 4 Definition
More informationMR2 MKII Electric Aerial
Introduction This document aims to provide as much information as you are likely to need for the MKII MR2 electric aerial. It has been compiled based on personal experience gained from installing my own
More informationInstructions for Assembling Driving Wheels, Axles and Crankpins
Instructions for Assembling Driving Wheels, Axles and Crankpins (Version 1; October 2008) Introduction These instructions explain how to assemble Exactoscale 4mm scale driving wheels, axles and crankpins
More informationMacBook Pro 13" Unibody Mid 2009 LCD Replacement
MacBook Pro 13" Unibody Mid 2009 LCD Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION Save money by replacing just the LCD rather than the whole display
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2004-2008 Ducati ST3/ST4 HeliBars Replacement Handlebar Risers P/N: HB2405 IMPORTANT: PLEASE GIVE CUSTOMER ENCLOSED INFORMATION! Thank you for your purchase of our HeliBars. They
More informationCHECKLIST & COMPONENTS
Eclipse Compact www.rollershuttercompany.com Tel 0800 6444121 55mm Roller Garage Doors CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape measure Power drill 10mm A/F
More informationDisco 3 Clock Spring / Rotary Coupler replacement
Disco 3 Clock Spring / Rotary Coupler replacement I recently had to change my Clock spring and thought some folks may find it helpful to see what it entailed. I did lots of reading around but couldn t
More informationRebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL
Rebuilding the Power Steering Pump for a 2007 Honda Accord 4CYL Disclaimer: I have benefited greatly from others who have taken the time to post auto repair videos/tutorials online. To try and return the
More informationBag 1. Bag 1. Center Pivot. Center Pivot
8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball
More informationWritten By: Markus. Step-by-Step guide how to replace a dead NICD-Battery with LiFePO-Batteries. Rollei 6000/6008 Battery LiFePO4 Replacement
Rollei 6000/6008 Battery LiFePO4 Replacement Step-by-Step guide how to replace a dead NICD-Battery with LiFePO-Batteries. Written By: Markus ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION
More informationPLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!!
JDM power folding mirror switch install into stock USDM harness. By: Greg L., Zeke21 on twinturbo.net PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!! This is how I was able to get the
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationM52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit
Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure
More informationIntegrated Engineering Solid Shift Bushing Installation Guide
Integrated Engineering Solid Shift Bushing Installation Guide Thank you for purchasing another high quality Integrated Engineering product! This instruction sheet is used for installation of the Integrated
More informationWritten By: Andrew Optimus Goldberg
Remove the battery from your iphone 5. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Bring life back to your iphone 5 with a new battery. If your battery
More informationWritten By: Sam Lionheart
iphone 5s Battery Replacement Replace the battery in your iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION Use this guide to bring life back to your iphone
More informationMK7 GTI Electronic Folding Mirror Conversion
MK7 GTI Electronic Folding Mirror Conversion 01 Mirror and Switch Installation 1. Using a soft pry tool remove the trim panel on the driver side door handle. 02 2. Remove 2 T-30 torx screws. 03 3. On the
More informationHP LASERJET
HP LASERJET 4200 4300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP LASERJET 4200 TONER CARTRIDGE (Q1338A) HP LASERJET 4300 TONER CARTRIDGE (Q1339A) REMANUFACTURING HP LASERJET 4200/4300 TONER CARTRIDGES
More informationImproving the casting performance on old Ambassadeurs for free!
Improving the casting performance on old Ambassadeurs for free! Whenever I acquire a fishing reel I will always strip it down and give it a service-it doesn t matter if the reel is new or old. Sometimes
More informationINSTALLING A 1977 THRU 1982 C3 STEERING COLUMN INTO A EARLIER 1969 THRU 1976 MODEL CORVETTE
Last Revised: 23FE2011 INSTALLING A 1977 THRU 1982 C3 STEERING COLUMN INTO A EARLIER 1969 THRU 1976 MODEL CORVETTE Why Make This Installation Starting in 1977 and carrying thru 1982, the C3 Corvette steering
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationWritten By: Evan Noronha
iphone 6s Plus Battery Replacement Replace the battery in an iphone 6s Plus. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Use this guide to bring life back to your
More informationHub Kit Fitting Guide 36V/HL
Hub Kit Fitting Guide 36V/HL Important: For your own safety you must read this manual before attempting to fit any part of the motor kit to your bike. You must also ensure that you fit the kit in strict
More informationInstallation Directions for FINGER STICK and Blocker Plate
Installation Directions for FINGER STICK and Blocker Plate What is a Finger Stick? A Finger Stick is a simple circuit that modifies the MAF signal on LLY and LBZ engines (not LB7 engines) to expected levels
More informationInstallation Instructions for Chevrolet C5 Corvette Lingenfelter High Flow Fuel Pump Module
Installation Instructions for 1997-2003 Chevrolet C5 Corvette Lingenfelter High Flow Fuel Pump Module PN: L710650197 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552
More informationLMT Lens/Optics Cleaning Procedure. Lens Cleaning Procedure
SVC-LMT-Procedure REV. TBD Product Support Engineer: Effective: Sheet: MP 04/13/11 Pg. 1 of 10 Lens 1. Assemble the following cleaning components as depicted in Figure 1. Alcohol Canned Dry Air Nozzle
More information