Hunger DFE GmbH Tandem Seal. Hunger DFE Tandem Seal
|
|
- Adele Arnold
- 5 years ago
- Views:
Transcription
1 Hunger DFE GmbH Tandem Seal Hunger DFE Tandem Seal Hunger DFE Tandem Seals were particularly designed for application as rod and piston seals. Two types of this product range shall be presented at this point: Rod/Piston Seal TDI/TDA consists of two parts, an elastic ring of PUR with a sealing lip and a slide ring of abrasion resistant PTFE-Bronze-Compound with a sealing edge. Prior to fitting, the sealing lip protrudes beyond the nominal diameter of the seal and when fitted is pressed against the piston rod. Effective sealing is thereby provided at zero pressure. The interaction of both sealing elements results in the following advantages: very low friction coefficient low-wear = long life high reliable sliding speeds up to 1m/s no stick-slip effect high sealing effect due to tandem system (two seals in one groove) TDA TDI Rod/Piston Seal TDMI/TDMA as well consists of two sealing elements, an elastic ring of PUR with two sealing lips and a slide ring of abrasion resistant PTFE-Bronze- Compound. It is applied for the sealing of plunger pistons and piston rods. This tandem seal can be used in hydraulic oil based on mineral oil and compressed air. The use of TDMI/TDMA is recommendable in applications which require the separation of different media on both sides. TDMA TDMI
2 Hunger DFE GmbH Compact Seals for Pistons Hunger DFE Compact Seal for Pistons The Hunger DFE slide ring piston seal type GD1000K is used to seal and guide pistons on double-acting hydraulic cylinders. The seal design and materials used make it particularly suitable for the most vigorous applications e.g. construction machine cylinders. The GD1000K consists of 6 parts, a special shaped elastic ring of a modified NBR, a slide ring of abrasion resistant PTFE-Bronze compound which acts as the sealing ring, two lateral support rings of modified PUR and two bearing rings of pressureresistant POM-PTFE- Bronze-Compound. The design of GD1000K ensures: fast response of the seal higher sealing effect longer service life higher resistance to media lower friction coefficient and excellent efficiency
3 Hunger DFE GmbH Bearing Rings Hunger DFE bearing rings Hunger DFE bearing rings types FI, FA, FAI provide full surface contact between sliding surfaces at all times. Seal installation is very easy when combined with the use of HUNGER bearing elements: The maximum piston diameter, which the slide ring or sealing element has to pass over during assembly, is smaller with the use of FA type bearings than with conventional bearing rings. In most cases the slide ring does not need to be expanded for fitting. The minimum diameter of the rod seal and bearing housing, through which the seals have to pass during fitting, is larger with the use of FI and FAI type bearings. Due to the full coverage of the sliding surface by low-friction POM- PTFE-Compound an almost constant friction coefficient can be achieved at low as well as at high speeds. Hunger DFE bearing rings feature the following characteristics: temperature ranges between -55 and +120 C sliding speeds up to 3 m/s can be used in media such as standard hydraulic oils, oil-water, water-glycol or synthetic fluids Advantages of Hunger HUNGER DFE bearing elements FI, FAI, FA: no metallic contact due to special profile shape and high-strength plastics no blocked filters due to abrasion as with cotton-reinforced fabrics easy fitting, secure arrangement in combination with Hunger seals no stick-slip effect wear resistant and long operation life FAI FI
4 Hunger DFE GmbH Bearing Rings
5 Hunger DFE GmbH Wipers Hunger DFE Wiper The Hunger DFE wiper type AI has the function to keep out extremely fine dust, dirt, metal particles, grains of sand etc. so that the bearing elements and seals arranged behind it are not subjected to premature wear as a result of contaminant ingress. Wiper type AI covers a temperature range from C and can reach a sliding speed of 1 m/s. The AI wiper can be used with mineral oils and many other types of hydraulic fluids. Materials like NBR, Hytrel or FPM are part of our standard programme. However, wipers made of other materials like PTFE pure, PUR, NBR or Hytrel can also be supplied according to customer s requirements. AI-D AI-ST AI
Merkel Double Wiper PT 2
Merkel Double Wiper PT 2 Merkel Double Wiper PT 2 Material O-rings Profile ring Profile ring Material PTFE bronze compound Code PTFE B602 Fig. 1 Merkel Double Wiper PT 2 O-ring Material Code Hardness Nitrile
More informationPolon Rod sealing set
The single-acting rod sealing set profile consists of a PTFE rod sealing ring and an elastomer O-Ring as a preloading element. The asymmetrical cross-section of the slipper ring is designed for best drag
More informationPolon Piston sealing set
The double-acting piston sealing set profile consists of a PTFE piston sealing ring and an elastomer O-Ring as a preloading element. Profile is particularly suitable for double-acting pistons in control
More informationMerkel U-Ring Seal Set 0216
Merkel U-Ring Seal Set 0216 Merkel U-Ring Seal Set 0216 NBR U-ring Backring Fabric U-ring NBR Cotton fabric Code 80 NBR B246 BI-NBR B4 B248 Back-up ring Fig. 1 Merkel U-Ring Seal Set 0216 Product description
More informationPOLYPAC R WRM/C B+S SA
POLYPAC R WRM/C B+S SA - Single Acting - - With Metal Case - - For open Assembly - -Material- - NBR and Metal - 75 76 Scraper WRM/C - SA Scraper WRM/C - SA Description WRM/C and SA are mould-vulcanised
More informationCapseal FOR HYDRAULIC AND PNEUMATIC CYLINDERS AND VALVES
Capseal FOR HYDRAULIC AND PNEUMATIC CYLINDERS AND VALVES What is Capseal? Capseal is a combination seal of rubber O-ring and Sunflon ring. This unique seal provides low friction operation and reduce possible
More informationDescription Product group Rod seal
Description Product group Rod seal Design N symmetrical u-ring (05) NI asymmetrical u-ring with inner main sealing lip (07) Profile no. 05/07 Specification E suitable for onesided pressure load Model STI
More informationRB NOK Asymmetrical Profile Rod U-Cup with Double Lip RB asymmetrical C-cup is suited for heavy
RB NOK Asymmetrical Profile Rod U-Cup with Double Lip RB asymmetrical C-cup is suited for heavy duty mobile and stationary service when rod leakage must be kept to a minimum. Double lip design reduces
More informationCompact Seal. DUOPAC rubber fabric reinforced compact seals Type DPS and DPC. Busak+ Shamban
DUOPAC rubber fabric reinforced compact seals Type DPS and DPC Description The compact seals DUOPAC DPS and DPC types are double acting piston seals with integrated guide rings. DUOPAC has been designed
More informationZurcon U-Cup RU2. Single Acting U-Cup Asymmetric, Double Lip, Compact Material: Zurcon
Single Acting U-Cup Asymmetric, Double Lip, Compact Material: Zurcon 121 122 U-Cup RU2 Description Today U-Cups are used primarily as seals for piston rods in hydraulic cylinders. U-Cups in polyurethane
More informationMERKEL P7 Wiper Single-acting rod wiper made from Polyurethane with integrated metal retainer. PUR wiper for axial-accessible housings.
Página 1 de 5 PT 1 MERKEL PT 1 Low Friction Wiper Low friction wiper consisting of one profile ring with a sealing edge and a wiper edge, as well as two O-Rings as pre-load components. A wiper for improvement
More informationSeals On Demand engineered, machined, delivered.
SEALS ON EMAN Seals On emand engineered, machined, delivered. Hercules Seals On emand offers you a wide selection of custom, cost-effective sealing solutions, using advanced rapid-prototype technology.
More informationPOLYPAC - Selemaster SM. Single Acting Compact Rod Seal With Anti-extrusion Ring Material: Rubber + Fabric Reinforced Rubber + POM
Single Acting Compact Rod Seal With Anti-extrusion Ring Material: Rubber + Fabric Reinforced Rubber + POM 85 86 Selemaster SM The rod seal range has been designed to meet the needs of hydraulic equipments
More informationOperating conditions. Surface roughness R a R max
Merkel U-Ring NI 300 Merkel U-Ring NI 300 Asymmetrical sealing lips PUR profile ring Sealing edge Material Material Code Hardness Polyurethane 94 AU 925 94 Shore A Operating conditions Material 94 AU 925
More informationUPN. Rod and piston seal with energizing element UPN
Rod and piston seal with energizing element MATERIAL 1 1 Type Polyurethane Designation SEALPUR 93 Hardness 93 ShA 2 2 Type Nitril Rubber NBR Designation RUBSEAL 70 Hardness 70 ShA Pressure 400 bar FIELD
More informationMerkel Compact Seal S 8
Merkel Compact Seal S 8 Merkel Compact Seal S 8 Material Rubber head Fabric part Material Code Hardness Nitrile rubber NBR 70 NBR B209 70 Shore A Operating conditions Fig. 1 Merkel Compact Seal S 8 Product
More informationP54 PISTON SEAL TECHNICAL DETAILS. Part Number Structure. Double-Acting F E A T U R E S P54 M R N HLX. Compact piston design.
PISTON SEAL Double-Acting TECHNICAL DETAILS The Hallite P54 is a double-acting, o-ring energized, low-friction piston seal that performs well in both high- and low-pressure systems. High-performance Armorlene
More informationZurcon U-Cup RU /*"-8#+-8 " (&*$8 " %*+(+$4
Zurcon U-Cup RU9 Your Partner for Sealing Technology Trelleborg Sealing Solutions is a major international sealing force, uniquely placed to offer dedicated design and development from our market-leading
More informationMerkel U-Ring NI 300. Hydraulics Rod Seals Merkel U-Ring NI 300. Merkel U-Ring NI 300. Material. Operating conditions. Product description
Merkel U-Ring NI 300 Merkel U-Ring NI 300 Asymmetrical sealing lips PUR profile ring Sealing edge Material Material Code Hardness Polyurethane 94 AU 925 94 Shore A Operating conditions Material 94 AU 925
More informationOperating conditions. * Surface roughness of the sliding surface to suit the sealing component used.
Merkel Wiper P 6 Merkel Wiper P 6 Material Wiper lip Material Code Hardness Nitrile rubber NBR 85 NBR B247 85 Shore A Fluoro rubber FKM 85 FKM K664 85 Shore A Operating conditions Fig. 1 Merkel Wiper P
More informationGeneral information on radial seals
170 General information on radial seals Radial seals is the common name for shaft seals, which seal against a rotating shaft using an elastic and resilient lip of rubber or PTFE. The lip in turn is either
More informationDesign Ref. Material Dimensions metr. inch NR IR SBR BR IIR EPDM NBR ECO CR CSM AU, EU HNBR VMQ Q } PVMQ FVMQ FPM ACM FFKM PTFE NBR EPDM FPM VMQ
Design Ref. Material Dimensions metr. inch OR O-Ring Encapsulated FEP-O-ring NR IR SBR BR IIR EPDM ECO CR CSM AU, EU H VMQ Q } PVMQ FVMQ FPM ACM FFKM PTFE Approved compounds: DIN-DVGW, KTW, WRC, FDA, NSF,
More informationDucted HEPA filter units for highly sensitive areas
Ducted HEPA filter units for highly sensitive areas Without prefilter casing: Type F60 With prefilter casing: Type F70 Duct casing for installation into ductwork, with or without prefilter Double-groove
More informationPT 1 MERKEL PT 1 Low Friction Wiper Low friction wiper consisting of one profile ring with a sealing. Applications: Technical Data
PT 1 MERKEL PT 1 Low Friction Wiper Low friction wiper consisting of one profile ring with a sealing edge and a wiper edge, as well as two O-Rings as pre-load components. A wiper for improvement of overall
More informationAdditional products. Lip seals 50. Springs / Bonded seals 51. Hydraulic seals for high pressure 52. Hydraulic seals for medium high pressure 53
Lip seals 50 Springs / Bonded seals 51 Hydraulic seals for high pressure 52 Hydraulic seals for medium high pressure 53 O-Rings / Incofep 54 Vibration dampers 55 Mechanical Face Seals 56 Cassette Seals
More informationV-Rings around the clock... around the clock...
Description V-rings are rotary seals that can perform numerous jobs in their function of sealing rotating shafts: sealing against the penetration of dirt, dust, water or watery pollutants, combination
More informationSHAFT SEALS WITH PTFE COATING TCJ
SHAFT SEALS WITH PTFE COATING TCJ DESCRIPTION The TCJ profile is a shaft seal composed of a single metal cage with a rubber coating, PTFE-coated double sealing lip and integrated spring. ADVANTAGES Very
More informationDICHTOMATIK. Hydraulic seals
Titel Hydraulik 2008 GB:Titel 2008 10.09.2008 17:08 Uhr Seite 2 DICHTOMATIK Hydraulic seals DICHTOMATIK Hydraulic seals Albert-Schweitzer-Ring 1 D-22045 Hamburg P.O. Box 70 04 80 D-22004 Hamburg Phone
More informationno adhesion effect on sliding surface, even after a long standstill superior performance over a wide range of temperatures and hydraulic fluids
Industrial Seal Inc. offers a wide range of hydraulic and pneumatic Piston seal profiles to meet the broad demands of the fluid power industry. These Piston seals are offered in a variety of compounds
More informationJacking and Equalizing Cylinders for NASA- Crawler Transporter
Group 12 - Special Applications Paper 12-1 307 Jacking and Equalizing Cylinders for NASA- Crawler Transporter Dr.- Ing. Ingo Rühlicke, MBA Walter Hunger GmbH & Co. KG, Rodenbacher Str. 50, 97816 Lohr am
More informationSeals Stretch Running Friction Friction Break-Out Friction. Build With The Best!
squeeze, min. = 0.0035 with adverse tolerance build-up. If the O-ring is made in a compound that will shrink in the fluid, the minimum possible squeeze under adverse conditions then must be at least.076
More informationUNLEASH THE POWER REAL-WORLD SOLUTIONS
FLUID POWER UNLEASH THE POWER The fluid power industry is not only solidifying a hold on current applications, it is unleashing its knowledge into everincreasing frontiers. Excessive temperature and diverse
More informationParker Fluid Power Seals. JIS series
Parker Fluid Power Seals JIS series Table of Contents Contents page Introduction... 1 Sealing Systems... Wipers AF... 3 AG... 5 AH...... 10 AY... 1 Rod Seals B3... 15 BR(buffer)... 0 Piston Seals B7......
More informationFREUDENBERG XPRESS CUSTOM-MANUFACTURED SEALS
FREUDENBERG XPRESS FREUDENBERG XPRESS CUSTOM-MANUFACTURED SEALS In today s economic environment Freudenberg Xpress is the clear solution for companies needing precise and speedy results. Short turnaround,
More informationSKF SEAL JET DD. Machined seals product range
SKF SEAL JET DD Machined seals product range 2 Content A Introduction Machined seals concept... 5 Sealing materials... 6 Introduction... 6 Thermoplastic elastomers - Polyurethanes... 7 Thermoplastic elastomers
More informationMerkel PRW 1 Double Wiper with Integrated Pressure Relieve. Product Information Merkel Hydraulics
Merkel PRW 1 Double Wiper with Integrated Pressure Relieve Product Information Merkel Hydraulics Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global Technology
More informationZURCON L-CUP. - Single Acting - Innovative Design based on U-Cup - Low Friction Properties - Material - Polyurethane Busak+ Shamban
contents (catalogue) main menu product range fullscreen/variable R ZURCON L-CUP - Single Acting - Innovative Design based on U-Cup - Low Friction Properties - Material - Polyurethane 81 82 Zurcon R L-Cup
More informationFAX FAX
2 seals on eman HERCULES SEALS ON EMAN provies a wie selection of custom, cost effective sealing solutions using avance rapi-prototype technology. The programmable CNC prouction cell can manufacture both
More informationSCRAPERS. Busak+ Shamban
SCRAPERS 1 2 Scrapers Contents Choice of Scraper Element... 4 Turcon R Excluder R 2... 7 Turcon R Excluder R 5... 15 Turcon R Excluder R 500... 23 Scraper DA17... 29 Scraper DA22 and RSW... 35 Scraper
More informationDimensions and types. Type BA. Type BAS
and types BA Way wipers of this type are used mainly in those cases where installation conditions are restrictive, or where the wipers are additionally protected by means of a telescopic cover, a bellows,
More informationReturn-Suction Filters E 068 E 088. In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min e
Return-Suction Filters E 68 E 88 In-line mounting Connection up to G¾ Nominal flow rate up to l/min.8-e Description Application For operation in units with hydrostatic drives, when the return flow is under
More informationOperating manual Keula gate valves DN PN10/16
Operating manual Keula gate valves DN40-400 PN10/16 Page - 1 Manufacturer: Keulahütte GmbH Geschwister-Scholl-Str. 15 02957 Krauschwitz GERMANY Manufacture and sale of the slide valves: Slide valves according
More informationTurcon Glyd Ring. Double Acting Rubber Energized Plastic Faced Seal Material: Turcon, Zurcon and Elastomer
Turcon Glyd Ring Double Acting Rubber Energized Plastic Faced Seal Material: Turcon, Zurcon and Elastomer 15 Turcon Glyd Ring 16 Turcon Glyd Ring Turcon Glyd Ring Description Successfully used for decades,
More informationFNA 045 Operating pressure up to 7 bar / 101 psi Nominal flow rate up to 45 l/min / 12 gpm
Off-line Filter Unit FNA 045 Operating pressure up to 7 bar / 101 psi Nominal flow rate up to 45 l/min / 12 gpm Description Application In the by-pass flow of hydraulic and lubrication systems. Performance
More informationTurcon RotoGlydRing. Latest information available at Edition August
Turcon RotoGlydRing 241 242 Turcon Roto Glyd Ring n TURCON ROTARY SEALS - ELASTOMER ENERGIZED n Turcon Roto Glyd Ring Description The Turcon Roto Glyd Ring is used to seal rods, shafts, axles, bores, rotary
More informationFN 060 FN 300 In-line mounting Operating pressure up to 12 bar / 174 psi Nominal flow rate up to 650 l/min / 172 gpm
Off-line Filters FN 6 FN In-line mounting Operating pressure up to bar / 74 psi Nominal flow rate up to 65 l/min / 7 gpm Description Application Return-flow filter or off-line filter in hydraulic and lubrication
More informationExclusive distributor of. guide rings and bushes. issue one. issue one
issue one issue one Exclusive distributor of guide rings and bushes by p: 0800 822 722 www.pacificseals.co.nz e: info@pacificseals.co.nz bout Pacific Seals Pacific Seals is New Zealand s premier seal distributor
More informationMerkel Sealing Technology for the Ferrous & Non-Ferrous Processing Industries
Merkel Sealing Technology for the Ferrous & Non-Ferrous Processing Industries Merkel Heavy Industry 2 Merkel Sealing Technology Seals and Sealing Systems for the Ferrous & Non-Ferrous Processing Industries
More informationMerkel Sealing Technology for the METALLURGICAL INDUSTRY. Freudenberg Sealing Technologies
Merkel Sealing Technology for the METALLURGICAL INDUSTRY Freudenberg Sealing Technologies 2 Merkel Sealing Technology for the METALLURGICAL INDUSTRY Installation recommendations for sealing systems plus
More informationFNA 008 FNA 016 Operating pressure up to 4 bar / 58 psi Nominal flow rate up to 16 l/min / 4.2 gpm
Off-line Filter Units FNA 008 FNA 016 Operating pressure up to 4 bar / 58 psi Nominal flow rate up to 16 l/min / 4.2 gpm Description Application In the by-pass flow of hydraulic and lubrication systems.
More informationE 068 E 088 In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min
Return-Suction Filters E 68 E 88 In-line mounting Connection up to G¾ Nominal flow rate up to l/min Description Application For operation in units with hydrostatic drives, when the return flow is under
More informationES 074 ES 094 Tank top mounting Connection up G1¼ Nominal flow rate up to 80 l/min
Suction Filters ES 074 ES 094 Tank top mounting Connection up G1¼ Nominal flow rate up to 80 l/min Description Application To be installed in the suction line of the pumps of hydraulic systems resp. upstream
More informationmmetric Master Seals Catalogue 05/06
mmetric NR Master Seals Catalogue NR Contents Metric Seals Seal Index Piston Double Acting 01 Piston Seals 02 Glide Rings 03 Piston Rings 04 Pneumatic Piston and Seal Piston Single Acting 05 Piston Seals
More informationAngle Seat Valve 7010
Angle Seat Valve 7 DN 8 up to DN 8 PN 16 - PN Pneumatically operated angle seat valve for the control of neutral, slightly aggressive and highly aggressive media. Compact design Unaffected by lightly contaminated
More informationQuantum PTFE Products
Quantum PTFE Products Quantum PTFE Products Quantum PTFE Seals Simrit, the industrial division of Freudenberg NOK, strives to meet today s ever-increasing demand for highperformance materials. Polytetrafluoroethylene
More informationHigh performance S1S hydraulic seals. Providing a longer and more reliable life-cycle for hydraulic cylinders
High performance S1S hydraulic seals Providing a longer and more reliable life-cycle for hydraulic cylinders A leader in sealing technology Reduced leakage and friction, together with a long and reliable
More informationHeavy Duty Wheel Seals and Agricultural Equipment Seals
Heavy Duty Wheel Seals and Agricultural Equipment Seals About TCS Heavy Duty Wheel Seals and Agricultural Equipment Seals Heavy Duty Wheel Seals and Agricultural Equipment Seals can be divided into AP
More informationAngle Seat Valve 7010
Angle Seat Valve 7 DN 8 up to DN 8 PN 16 - PN 4 Pneumatically operated angle seat valve for the control of neutral, slightly aggressive and highly aggressive media. Compact design Unaffected by lightly
More informationPneumatic Seals 1/2 Pneumatic Seals 2/2. Pneumatic Seals
Seals Seals * 1 Mpa = 10 Bar 1 Bar = 14.5 psi 1 Mpa = 145 psi Combination Wiper/Rod Seal This pneumatic rod seal/wiper Set profile is fitted into housings with a circlip recess according DIN 7993 (type
More informationSEALING SOLUTIONS FOR YOUR DRIVES
Intelligent Drivesystems, Worldwide Services SEALING SOLUTIONS FOR YOUR DRIVES EN SEALING SYSTEMS FOR NORD GEAR UNITS AND GEARED MOTORS SEALING SYSTEMS FOR NORD GEAR UNITS AND GEARED MOTORS NORD DRIVESYSTEM
More informationMAXIFLUSS. Fire-safe Rotary Plug Valves
MAXIFLUSS Fire-safe Rotary Plug Valves Strong. Rugged. Reliable. Technical benefits MAXIFLUSS rotary plug valves by VETEC have a double-eccentric design. They feature high flow capacities and an excellent
More information11 Maintenance of Handrail Section
11 Maintenance of Handrail Section V-Type Handrail Q 409 603 11 Maintenance of Handrail Section 11.1 V-Type Handrail Q 409 603 1 Description and Mode of Operation The handrail is provided with a multilayered,
More informationPolyseal Total Sealing Technology
ontents ompany Profile Product Range Index Product Range Section / Piston Seals Section B S/ Piston Seals Section Rod Seals Section Rod Wipers Section E Bearing rings Section F ORings & Backup Rings Other
More informationSeries TSW Sheet No J. SUCTION FILTER, horizontal tank mounted. Dimensions: mounting surface
SUCTION FILTER, horizontal tank mounted Sheet No. 1905 J Series TSW 210-310 Dimensions: type TSW 210 TSW 310 connection - 20 SAE -20 SAE A 12.09 15.47 B 11.57 14.96 C 11.42 14.76 D 8.62 12.00 E.26.30 weight
More informationMerkel Guide Ring Guivex SBK
Product description Guide rings for piston rods can be used for very heavy loads in hydraulics. The profiling (patented) on the static side of the guide ring ensures an even distribution of stress. Product
More informationConstruction characteristics. Technical characteristics. End plates Rod Barrel Rod-guide bushing Piston
Construction characteristics nd plates Rod Barrel Rod-guide bushing Piston Seals Cushion adjusting screws die-casting aluminium C3 chromed steel or stainless steel aluminium alloy anodised spheroid bronze
More informationThe New Generation ISO Cylinders for a Dynamic Future
Electric Drives Linear Motion and and Controls Hydraulics Assembly Technologies Pneumatics Service The New Generation ISO Cylinders for a Dynamic Future Rexroth s new generation of ISO pneumatic cylinders
More informationNessie 2/2 way Solenoid valves for High Pressures and High Temperatures, type VDHT
Nessie 2/2 way Solenoid valves for High Pressures and High Temperatures, type VDHT Valve program for small and medium flows: VDHT 3/8 E 2/2 VDHT 1/2 E 2/2 VDHT 3/8 EA 2/2 VDHT 1/2 EA 2/2 Valve program
More informationHydraulic Cylinder Catalogue
Hydraulic Cylinder Catalogue Danver Hydromatics Private Limited 10/23, Siddhinath Chatterjee Road, Behala, Kolkata -700034 Works: - Chakpara, Balitikuri, Jagacha, Howrah 711113 Contact: - 033-2653 4496,
More informationConveyor Solutions. Trellex FLEXOPIPE
EN Trellex FLEXOPIPE 2 Trellex FLEXOPIPE flexible, unique, ecological! Conveyor belt systems of enclosed material transport are an excellent solution to various conveying problems. Metso is Europe s leading
More informationIntermot Hydraulic Motors. Drum Brakes RC Series
Intermot Hydraulic Motors Drum Brakes RC Series TECHNICAL CATALOGUE INDEX General information Pag. 10 Technical data Pag. 14 Dimensional drawings Pag. 15 Ordering instructions Pag. 17 9 Hydraulic fluids
More informationL L L L Connection up to M60 x 2 Nominal flow rate up to 850 l/min
Ventilating Filters L1.0406 L1.0506 L1.0706 L1.0807 Connection up to M60 x 2 Nominal flow rate up to 850 l/min Description pplication Ventilation of tanks for hydraulic and lubrication systems and gearboxes.
More informationHydraulic seals. A wide range for hydraulic cylinders in off-highway applications. The Power of Knowledge Engineering
Hydraulic seals A wide range for hydraulic cylinders in off-highway applications The Power of Knowledge Engineering Optimizing hydraulic cylinder sealing system performance See what you can achieve with
More informationWILLBRANDT Rubber Expansion Joint Type 40
0 Type is a highcorrugated, highly elastic rubber expansion joint. Due to its corrugation it has very low inherent resistance. It is characterised by its ability to absorb a large amount of movement in
More informationPressure transmitter for general applications Model S-10, standard version Model S-11, flush diaphragm
Electronic Pressure Measurement Pressure transmitter for general applications Model, standard version Model S-11, flush diaphragm WIKA Data Sheet PE 81.01 Applications n Mechanical engineering n Hydraulics
More informationO-Ring. FEP O-Ring. PTFE O-Ring. Isolast Perfluoroelastomer O-Ring
O-Rings O-Ring Double acting seal for static and dynamic applications. Available in various materials e.g. nitrile (NBR), fluorocarbon (FKM), ethylene propylene (EPDM), chloroprene, silicon, fluorosilicone,
More informationSTANDARD SHAFT SEALS VB
STANDARD SHAFT SEALS VB DESCRIPTION The VB profile is a shaft seal composed of a single external metal cage with an internal rubber coating and a primary sealing lip without a spring. ADVANTAGES Good radial
More informationCYLINDRICAL ROLLER BEARING CATALOG TIMKEN SMALL BORE METRIC SEALS CATALOG
CYLINDRICAL ROLLER BEARING CATALOG ABOUT THE TIMKEN COMPANY The leading authority on tapered roller bearings, Timken today applies its deep knowledge of metallurgy, tribology and mechanical power transmission
More informationLS 025 LS 035 In-line mounting Connection up to G¾ / -12 SAE Nominal flow rate up to 33 l/min / 8.7 gpm
Suction Filters LS 025 LS 035 In-line mounting Connection up to G¾ / -2 SAE Nominal flow rate up to 33 l/min / 8.7 gpm Description Application To be installed in the suction line of the pumps of hydraulic
More informationWYECO. Y-Type Cylinder Actuated Valve. Model WY-C08YT-S
Y-Type Cylinder Actuated Valve Model WY-C08YT-S Model WY-C08YT-F Features Compact, Light weight, High quality High flow capacity Simple design, Easy to assembly Easy to install and maintain All stainless
More informationOther materials are available on request. Operating conditions
Merkel U-Ring T 18 Merkel U-Ring T 18 Asymmetrical sealing lip POM back-up ring PUR profile ring Profile ring Coe Harness Polyurethane 95 AU V142 95 Shore A Fig. 1 Merkel U-Ring T 18 Back-up ring Polyacetal
More informationService. Freudenberg NOK Sealing Technologies. Merkel Xpress
Service Freudenberg NOK Sealing Technologies Merkel Xpress Merkel Xpress Custom-Manufactured Seals Demanding projects often require high-quality seals without delay or hassle. Our Merkel Xpress sevice
More informationBALL VALVE Type HKSF-W
BALL VALVE Type HKSFW 1.2.2.1 Ball Valve Type HKSFW Description of construction The RMA ball valves of the HKSFW type are of fully welded, maintenancefree design. HKSFW ball valves are available in three
More informationFA SERIES KNIFE GATE PNEUMATIC CYLINDERS... 8
FA SERIES KNIFE GATE PNEUMATIC CYLINDERS......... 8 section 8 154 ORDERING INFORMATION For Rod End Dimensions see back cover foldout... Dimensional Information FA SERIES DIMENSIONS BASIC DIMENSIONS PLUS
More informationOperating Instructions for Flow Indicator. Model: DAA
Operating Instructions for Flow Indicator Model: DAA 1. Contents 1. Contents... 2 2. Note... 3 3. Instrument Inspection... 3 4. Regulation Use... 3 5. Operating Principle... 4 6. Mechanical Connection...
More informationETF Series. Tanktop Mounted Return Line Filters max. 175 I/min - 6 bar. An economic return line filter. Product Features: Contact Information:
max. 75 I/min - 6 bar An economic return line filter Improved system protection The ETF Series utilizes a re-inforced co-polymer head equipped with 2 return ports and quick-release cover. Maximum pressure
More informationVSI. Series BFII WATERWORKS. BUTTERFLY VALVES CONFORMING TO AWWA C504 Replaceable Seated 24-Inch and Greater Butterfly Valve
M M Series BFII BUTTERFLY VALVES CONFORMING TO AWWA C504 Replaceable Seated 24-Inch and Greater Butterfly Valve Publication 504-106 Issue 06/12 Design Features General All AWWA Butterfly Valves are of
More informationPart C: Electronics Cooling Methods in Industry
Part C: Electronics Cooling Methods in Industry Indicative Contents Heat Sinks Heat Pipes Heat Pipes in Electronics Cooling (1) Heat Pipes in Electronics Cooling (2) Thermoelectric Cooling Immersion Cooling
More informationGLADIATOR. GLADIATOR Telescopic Steel Covers
GLADIATOR GLADIATOR Telescopic Telescopic steel covers are used to protect slideways in certain machine tool applications. They offer effective protection against swarf and other debris. Liquid or coolant
More informationDryLin R Linear Plain Bearings, Fast and Quiet
+90º 40º +250º 100º Linear Plain Bearings, Fast and Quiet linear plain bearings, made from solid polymers, are dimensionally equivalent to standard ball bearings. They are made entirely of wear resistant
More informationISO Cylinders Compact Cylinders TC08 Series Plastic Finger Tight Fittings
ISO 632 Cylinders ISO 15552 Cylinders Compact Cylinders TC08 Series Pilot Valves 207-208 209-212 213-21 215 TC15 Series Pilot Valves TC08 Series Solenoid Valves CD7 Series Solenoid Valves CD12 Series Solenoid
More informationGeneral catalogue incl. replacement lists
Circulation pumps effiziente Pumpentechnologie General catalogue 2009 incl. replacement lists Data might be subject to alteration, errors excepted! Content I. Product programme Product overview... 1 Type
More informationES 134 ES 144 Tank top mounting Connection up to SAE 1½ Nominal flow rate up to 130 l/min
Suction Filters ES 134 ES 144 Tank top mounting Connection up to SAE 1½ Nominal flow rate up to 130 l/min Description Application To be installed in the suction line of the pumps of hydraulic systems resp.
More informationMore power Filtration solutions for CHP systems and gensets
More power Filtration solutions for CHP systems and gensets Full speed for your power generation High quality Gensets are used for decentralised power generation in fleets, combined heat and power (CHP)
More informationPressure balance Differential pressure version Model CPB5600DP
Calibration technology Pressure balance Differential version Model CPB5600DP WIKA data sheet CT 31.56 for further approvals see page 7 Applications Primary standard for the calibration of differential
More informationRADIAL SHAFT SEALS FOR PROCESS TECHNOLOGY APPLICATIONS
RADIAL SHAFT SEALS FOR PROCESS TECHNOLOGY APPLICATIONS RADIAMATIC HTS II The HTS II is a special PTFE variant of the Simmerring product group. This high-performance radial shaft seal sets standards in
More informationAxial Piston Units for Use with HF Fluids
RE 90 223/11.99 Replaces: 09.90 Axial Piston Units for Use with HF Fluids For mineral oil based fluids for axial piston units, see data sheet RE 90220 For environmentally acceptable fluids for axial piston
More informationSCHMITT. product information. Kreiselpumpen. U Pump Series. normal priming, centrifugal pumps with a single mechanical seal.
SCHMITT Kreiselpumpen chemical resistant pumps for corrosive and highly pure media product information U Pump Series normal priming, centrifugal pumps with a single mechanical seal materials: PVDF Description
More informationSCRAPERS/WIPERS Fits MS33675
123 SCRAPERS/WIPERS Fits MS33675 CUSTOMIZED DESIGNS Greene, Tweed offers a variety of scrapers and wipers to match any application challenge. From harsh media to extreme environmental conditions, Greene,
More informationINDUSTRIAL HOSES - compensators
Working parameters of rubber expansion joints The parameters of rubber compensators given in the tables (, temperature and displacement) are the maximum values and they must not occur simultaneously. The
More information