Merkel U-Ring Seal Set 0216
|
|
- Henry Simmons
- 5 years ago
- Views:
Transcription
1 Merkel U-Ring Seal Set 0216 Merkel U-Ring Seal Set 0216 NBR U-ring Backring Fabric U-ring NBR Cotton fabric Code 80 NBR B246 BI-NBR B4 B248 Back-up ring Fig. 1 Merkel U-Ring Seal Set 0216 Product description Two-piece Merkel seal set comprising an elastomer U-ring with an elastomer sealing edge, fabric reinforcement on the contact area and an active back-up ring. Merkel U-Ring Seal Set 0216 can also be used for pneumatic applications. Product advantages Single-acting rod seal for use in hydraulics and pneumatics Low friction due to fabric part Large range of dimensionse Protection against extrusion through activated back-up ring Low deformation value (not suitable for sealing systems) Easily installed in non-axial housings From 100 mm diameter. Application Pneumatic applications. D Code <300 mm Polyacetal POM POM PO202 >300 mm Polyamide PA 6.G200 Other materials like PTFE bronze back-up ring on enquiry. Operating conditions 80 NBR B246/BI-NBR B4B248/ POM PO NBR B246/BI-NBR B4B248/ PA 6.G200 Temperature range in C Hydraulic oils HL, HLP HFA fluids HFB fluids HFC fluids HFD fluids Water HETG (rapeseed oil) HEES (synthetic esters) HEPG (glycol) Mineral greases Pressure p in MPa Hydraulic 25 or 40* Pressure p in MPa Pneumatic 5 Running speed v in m/s 1,5 * max. pressure depends on the profile For Merkel U-Ring Seal Sets 0216, if long strokes are traversed, the max. pressure should only be applied to the last part of the stroke (closing pressure); during the stroke max. 16 MPa. Surface quality Surface roughness R a R max Sliding surface 0,05 0,3 µm 2,5 µm Groove base 1,6 µm 6,3 µm Groove flanks 3,0 µm 15,0 µm Percentage contact area M r >50% to max. 90% at cutting depth c = Rz/2 and reference line C ref = 0%.
2 Design notes Please observe our general design notes in Technical Manual. Gap dimension X2 The decisive factor for the function of the seal is the largest gap dimension occurring during operation on the non-pressurised side of the seal. Technical Manual. Profile 16 MPa 26 MPa 32 MPa 40 MPa D d X2 D d X2 D d X2 D d X2 <15 H10 f7 1,2 H10 f7 1,0 H10 f7 0,65 H10 f7 0,5 >15 H10 f7 1,8 H10 f7 1,4 H10 f7 0,90 H10 f7 0,7 The dimensions D1 and DF are to be viewed in connection with the sealing component used. Tolerance recommendation The admissible gap width, tolerances, guide play and deflection of the guide under load are to be taken into account when designing d2. Technical Manual. Fitting & installation Careful fitting is a prerequisite for the correct function of the seal. Technical Manual.
3 Article list H L +0, 2 R1 0, 4 20 Ø Ø d D C Ø D2 d D H L Profile C Article No ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D ,5 80 NBR B D NBR B D ,5 80 NBR B D NBR B D ,5 80 NBR B D NBR B D ,5 15 7,5 80 NBR B D ,5 80 NBR B D ,5 15 7,5 80 NBR B D ,5 80 NBR B D NBR B D NBR B D NBR B D ,5 15 7,5 80 NBR B D ,5 15 7,5 80 NBR B D NBR B D NBR B D NBR B D ,5 80 NBR B D NBR B D , NBR B D NBR B D ,5 80 NBR B D NBR B D ,5 80 NBR B D B Available from stock D On request: Tool is available, delivery at short notice
4 d D H L Profile C Article No , ,5 80 NBR B D , ,5 80 NBR B D ,5 80 NBR B D B Available from stock D On request: Tool is available, delivery at short notice
5 The catalog details are based on the experience of many years of research in the development and production of seals in the Freudenberg Group and correspond to our current level of knowhow. The sealing action of many catalog products is, however, not only created by the component itself. In many cases depending on the specifi c application it depends signifi cantly on the other parameters, such as installation point, counter surface, pressure, operating temperature, media to be sealed, lubrication, effects of vibration and any ingress of dirt from outside. These and other unknown factors in practical use may noticeably infl uence the functioning of the seals. Against this background generalised statements on the function of the catalog products are not possible. Details in this catalog merely represent general and non-binding reference values which make no claim to be valid for every application. We therefore recommend you to always discuss specifi c applications with our consultancy service. In the event of very high and special loads, for example due to aggressive media, the seal should be selected in co-operation with us; trials to check the functional reliability are often indispensable. Merkel Freudenberg Fluidtechnic GmbH Industriestr. 64 D Hamburg Tel.: +49(0)40/ Fax: +49(0)40/ merkel@freudenberg.de
Merkel Compact Seal S 8
Merkel Compact Seal S 8 Merkel Compact Seal S 8 Material Rubber head Fabric part Material Code Hardness Nitrile rubber NBR 70 NBR B209 70 Shore A Operating conditions Fig. 1 Merkel Compact Seal S 8 Product
More informationMerkel U-Ring NI 300. Hydraulics Rod Seals Merkel U-Ring NI 300. Merkel U-Ring NI 300. Material. Operating conditions. Product description
Merkel U-Ring NI 300 Merkel U-Ring NI 300 Asymmetrical sealing lips PUR profile ring Sealing edge Material Material Code Hardness Polyurethane 94 AU 925 94 Shore A Operating conditions Material 94 AU 925
More informationOperating conditions. * Surface roughness of the sliding surface to suit the sealing component used.
Merkel Wiper P 6 Merkel Wiper P 6 Material Wiper lip Material Code Hardness Nitrile rubber NBR 85 NBR B247 85 Shore A Fluoro rubber FKM 85 FKM K664 85 Shore A Operating conditions Fig. 1 Merkel Wiper P
More informationOperating conditions. Surface roughness R a R max
Merkel U-Ring NI 300 Merkel U-Ring NI 300 Asymmetrical sealing lips PUR profile ring Sealing edge Material Material Code Hardness Polyurethane 94 AU 925 94 Shore A Operating conditions Material 94 AU 925
More informationOther materials are available on request. Operating conditions
Merkel U-Ring T 18 Merkel U-Ring T 18 Asymmetrical sealing lip POM back-up ring PUR profile ring Profile ring Coe Harness Polyurethane 95 AU V142 95 Shore A Fig. 1 Merkel U-Ring T 18 Back-up ring Polyacetal
More informationMerkel Double Wiper PT 2
Merkel Double Wiper PT 2 Merkel Double Wiper PT 2 Material O-rings Profile ring Profile ring Material PTFE bronze compound Code PTFE B602 Fig. 1 Merkel Double Wiper PT 2 O-ring Material Code Hardness Nitrile
More informationØ range <500 mm. Ø range >500 mm. Operating conditions. Surface quality. Surface roughness R a R max
Hyraulics Ro Seals Merkel U-Ring T 20 Merkel U-Ring T 20 Merkel U-Ring T 20 PUR profile ring Material range
More informationMerkel Sealing Technology for the Ferrous & Non-Ferrous Processing Industries
Merkel Sealing Technology for the Ferrous & Non-Ferrous Processing Industries Merkel Heavy Industry 2 Merkel Sealing Technology Seals and Sealing Systems for the Ferrous & Non-Ferrous Processing Industries
More informationMerkel Sealing Technology for the METALLURGICAL INDUSTRY. Freudenberg Sealing Technologies
Merkel Sealing Technology for the METALLURGICAL INDUSTRY Freudenberg Sealing Technologies 2 Merkel Sealing Technology for the METALLURGICAL INDUSTRY Installation recommendations for sealing systems plus
More informationMerkel PRW 1 Double Wiper with Integrated Pressure Relieve. Product Information Merkel Hydraulics
Merkel PRW 1 Double Wiper with Integrated Pressure Relieve Product Information Merkel Hydraulics Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global Technology
More informationClaronPolyseal Single Acting Rod Seal PVM & PV
M & Metric tyle and M is a acting rod or piston seal for medium to heavy duty applications. The assembly consists of a male and female header and a series of 'V'. The number of 'V' may be varied to alter
More informationPolon Piston sealing set
The double-acting piston sealing set profile consists of a PTFE piston sealing ring and an elastomer O-Ring as a preloading element. Profile is particularly suitable for double-acting pistons in control
More informationPolon Rod sealing set
The single-acting rod sealing set profile consists of a PTFE rod sealing ring and an elastomer O-Ring as a preloading element. The asymmetrical cross-section of the slipper ring is designed for best drag
More informationDescription Product group Rod seal
Description Product group Rod seal Design N symmetrical u-ring (05) NI asymmetrical u-ring with inner main sealing lip (07) Profile no. 05/07 Specification E suitable for onesided pressure load Model STI
More informationMerkel Guide Ring Guivex SBK
Product description Guide rings for piston rods can be used for very heavy loads in hydraulics. The profiling (patented) on the static side of the guide ring ensures an even distribution of stress. Product
More informationReservoir oil filler/breather
Reservoir oil filler/breather RE 50070/10.05 Replaces: 01.03 1/10 Types ELF, BF and BL R 7802_2 Reservoir oil filler/breather with sieve type ELF 3... H_S_95 Reservoir breather type BF 7...K... Overview
More informationPOLYPAC - Selemaster SM. Single Acting Compact Rod Seal With Anti-extrusion Ring Material: Rubber + Fabric Reinforced Rubber + POM
Single Acting Compact Rod Seal With Anti-extrusion Ring Material: Rubber + Fabric Reinforced Rubber + POM 85 86 Selemaster SM The rod seal range has been designed to meet the needs of hydraulic equipments
More informationSTANDARD SHAFT SEALS VC
STANDARD SHAFT SEALS VC DESCRIPTION The VC profile is a shaft seal composed of a single metal cage with a rubber coating and a primary sealing lip without a spring. ADVANTAGES Very good static sealing
More informationSTANDARD SHAFT SEALS VB
STANDARD SHAFT SEALS VB DESCRIPTION The VB profile is a shaft seal composed of a single external metal cage with an internal rubber coating and a primary sealing lip without a spring. ADVANTAGES Good radial
More informationTurcon RotoGlydRing. Latest information available at Edition August
Turcon RotoGlydRing 241 242 Turcon Roto Glyd Ring n TURCON ROTARY SEALS - ELASTOMER ENERGIZED n Turcon Roto Glyd Ring Description The Turcon Roto Glyd Ring is used to seal rods, shafts, axles, bores, rotary
More informationSTANDARD SHAFT SEALS SC
STANDARD SHAFT SEALS SC DESCRIPTION The SC profile is a shaft seal composed of a single metal cage with a rubber coating and a primary lip with integrated spring. ADVANTAGES Very good static sealing Very
More informationMERKEL P7 Wiper Single-acting rod wiper made from Polyurethane with integrated metal retainer. PUR wiper for axial-accessible housings.
Página 1 de 5 PT 1 MERKEL PT 1 Low Friction Wiper Low friction wiper consisting of one profile ring with a sealing edge and a wiper edge, as well as two O-Rings as pre-load components. A wiper for improvement
More informationKANTSEAL. -Axial sealing - -Elastomers-
KANTSEAL -Axial sealing - -Elastomers- 61 62 n Description The Kantseal is agood alternative to the O Ring as an axial static seal in cases where particular demands are made. The application and handling
More informationSHAFT SEALS WITH PTFE COATING TCJ
SHAFT SEALS WITH PTFE COATING TCJ DESCRIPTION The TCJ profile is a shaft seal composed of a single metal cage with a rubber coating, PTFE-coated double sealing lip and integrated spring. ADVANTAGES Very
More informationO-RINGS AND STATIC SEALS
O-RINGS AND STATIC SEALS TECHNICAL PRINCIPLES ISC O-Rings 550 Static Sealing 552 Dynamic Sealing 558 Further Technical Notes 565 PRODUCTS Products 572 Design Types 573 Technical Principles O-Rings and
More informationHunger DFE GmbH Tandem Seal. Hunger DFE Tandem Seal
Hunger DFE GmbH Tandem Seal Hunger DFE Tandem Seal Hunger DFE Tandem Seals were particularly designed for application as rod and piston seals. Two types of this product range shall be presented at this
More informationMerkel Guide Ring Guivex SBK, KBK Reliable guides for rods and pistons. Product Information Merkel Hydraulics
Merkel Guide Ring Guivex SBK, KBK Reliable guides for rods and pistons Product Information Merkel Hydraulics Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global
More informationCompact Seal. DUOPAC rubber fabric reinforced compact seals Type DPS and DPC. Busak+ Shamban
DUOPAC rubber fabric reinforced compact seals Type DPS and DPC Description The compact seals DUOPAC DPS and DPC types are double acting piston seals with integrated guide rings. DUOPAC has been designed
More informationPressure reducing valve, pilot-operated. Type Z3DR. Contents. Features. RE Edition:
Pressure reducing valve, pilot-operated Type Z3DR RE 26874 Edition: 206-0 Size 0 Component series X Maximum operating pressure 350 bar Flow 20 l/min H8078 Features Sandwich plate valve Porting pattern
More informationPrecision Seals for Pneumatics
Precision Seals for Pneumatics Parker-Prädifa are the result of many years of compound and profile development experience, allowing the pneumatics engineer to pursue new design options and techniques such
More informationPrecision seals for pneumatics
Precision seals for pneumatics Parker Prädifa pneumatic seals are the result of many years of compound and profile development experience, allowing the pneumatics engineer to pursue new design options
More informationZurcon U-Cup RU /*"-8#+-8 " (&*$8 " %*+(+$4
Zurcon U-Cup RU9 Your Partner for Sealing Technology Trelleborg Sealing Solutions is a major international sealing force, uniquely placed to offer dedicated design and development from our market-leading
More informationPressure reducing valve, direct operated. Type ZDR. Contents. Features. RE Edition: Replaces:
Pressure reducing valve, direct operated Type ZDR RE 657 Edition: 8-3 Replaces: 8- Size 6 Component series 4X Maximum operating pressure 35 bar Maximum flow 5 l/min H775 Features Sandwich plate valve Porting
More informationPolyseal Total Sealing Technology
ontents ompany Profile Product Range Index Product Range Section / Piston Seals Section B S/ Piston Seals Section Rod Seals Section Rod Wipers Section E Bearing rings Section F ORings & Backup Rings Other
More informationHydraulic cylinders type CC - round heads with counterflanges to ISO nominal pressure 25 MPa (250 bar) - max 32 MPa (320 bar)
www.atos.com Table B-/E Hydraulic cylinders type CC - round heads with counterflanges to ISO 60 - nominal pressure MPa (0 bar) - max MPa (0 bar) SWC Cylinders Designer Software for assisted selection of
More informationIn case the operating parameters are requested at maximum level, these values may not be achieved.
All information contained in our catalogue is released only for general usage and not valid for special applications. Given parameters such as maximum pressure, temperature, sliding speed, surface contact
More informationCheck valve. Type S. Contents. Features. RE Edition: Replaces:
Check valve Type S RE 208 Edition: 201-08 Replaces: 201-0 Size 0 Component series 1X Maximum operating pressure 0 bar Maximum flow 0 l/min H8081 Features For threaded connection (screw-in thread) Leak-free
More informationCheck valve. Type S. Contents. Features. RE Edition: Replaces:
Check valve Type S RE Edition: - Replaces: - Sizes Maximum operating pressure bar Maximum flow l/min R8_ Features For threaded connection (screw-in thread) Leakage-free blocking in one direction Various
More informationPT 1 MERKEL PT 1 Low Friction Wiper Low friction wiper consisting of one profile ring with a sealing. Applications: Technical Data
PT 1 MERKEL PT 1 Low Friction Wiper Low friction wiper consisting of one profile ring with a sealing edge and a wiper edge, as well as two O-Rings as pre-load components. A wiper for improvement of overall
More informationCheck valve cartridge Type M-SR
RE /. Replaces:.9 Check valve cartridge Type M-SR Nominal sizes to Series X Maximum operating pressure bar Maximum flow L/min Overview of contents Contents Page Features Ordering details, symbols Preferred
More informationPressure Filter DF...K P, DF...M P, Flange Mounted
Pressure Filter, DF...M P, Flange Mounted up to 550 l/min, up to 260 bar DF...M P 330...1.X 160 240 280 500...1.X 660...1.X 660...2.X 990...2.X 1320...2.X 660...3.X 990...3.X 1320...3.X 1. TECHNICAL SPECIFICATIONS
More informationBlock mounting filter, lateral flange-mounting possible
Block mounting filter, lateral flange-mounting possible RE 0/.0 Replaces: 0.09 / Types 0/0 FEN 000 to 000; 0/0 FE 000, 00, 008 Nominal sizes according to DIN 0: 000 to 000 Nominal sizes according to BRFS:
More informationTurcon Glyd Ring. Double Acting Rubber Energized Plastic Faced Seal Material: Turcon, Zurcon and Elastomer
Turcon Glyd Ring Double Acting Rubber Energized Plastic Faced Seal Material: Turcon, Zurcon and Elastomer 15 Turcon Glyd Ring 16 Turcon Glyd Ring Turcon Glyd Ring Description Successfully used for decades,
More informationSuction Filter SF/SFM/SFF and Suction Filter Elements S/S..
Suction Filter /M/F and Suction Filter Elements S/S.. up to 500 l/min Filters: 60 110 160 240 330 M 330 F 400 F 500 Elements: S SH. SU. SG. 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The
More informationThrottle check valve. Type Z2FS. Contents. Features. RE Edition: Replaces: 10.07
Throttle check valve Type ZFS RE 758 Edition: 06-0 Replaces: 0.07 Size 0 Component series 3X Maximum operating pressure 35 bar [4569 psi] Maximum flow 60 l/min [4.3 US gpm] H5556 Features Sandwich plate
More informationReturn Line Filter RFM with 4-Hole Mounting
Return Line Filter with 4-Hole Mounting Tank-top mounted versions: up to 850 l/min, up to 10 bar 75 90 150 165 185 195 210 270 330 500 600 661 851 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction
More informationInline Filter MFM. Flow rates up to 100 l/min Pressure range up to 280 bar Material: EN-GJS / steel E /01.04
Inline Filter MFM Flow rates up to 100 l/min Pressure range up to 280 bar Material: EN-GJS 400-15 / steel 1. TECHNICAL SPECIFICATIONS 1.1. FILTER HOUSING Construction The inline filter consists of a filter
More informationPressure relief valve, pilot-operated. Type ZDB and Z2DB. Contents. Features. RE Edition: Replaces: 10.05
Pressure relief valve, pilot-operated Type ZDB and ZDB RE 575 Edition: 06- Replaces: 0.05 Size 6 Component series 4X Maximum operating pressure 35 bar Maximum flow 60 l/min H7746 Features Sandwich plate
More informationLine filter. Features. RE 51400/01.09 Replaces: Types 40/100 LEN 0040 to 0400; 40/100 LE 0003, 0015, 0018
Line filter RE /.9 Replaces: 8.8 / Types / LEN to ; / LE,, 8 Nominal sizes according to DIN : to Nominal sizes according to BRFS:,, 8 Nominal pressures, bar Connections up to G / Operating temperature
More informationHydraulic cylinders type CN - round heads with counterflanges to ISO nominal pressure 16 MPa (160 bar) - max 25 MPa (250 bar)
www.atos.com Table B80-/E Hydraulic cylinders type CN - round heads with counterflanges to ISO 600- - nominal pressure 6 MPa (60 bar) - max MPa (0 bar) SWC Cylinders Designer Software for assisted selection
More informationPressure Filter for Manifold Mounting DFP and for Reversible Flow DFPF
Pressure Filter for Manifold Mounting DFP and for Reversible Flow DFPF up to 600 l/min, up to 315 bar 60 110 140 160 240 280 330 500 660 1.X 660 2.X 990 1320 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING
More informationIntermot Hydraulic Motors. Drum Brakes RC Series
Intermot Hydraulic Motors Drum Brakes RC Series TECHNICAL CATALOGUE INDEX General information Pag. 10 Technical data Pag. 14 Dimensional drawings Pag. 15 Ordering instructions Pag. 17 9 Hydraulic fluids
More information2/2-way poppet valves with solenoid operation Type KSDER1
RE 8 36-0/0.0 Replaces: 07.0 /-way poppet valves with solenoid operation Type KSDER Build size T-3A cavity Maximum operating pressure 350 bar Maximum flow 0 L/min H/A/D 680/0 Type KSDER.A/HC... Overview
More informationReturn Line Filter RF
Return Line Filter up to 15000 l/min, up to 25 bar 30 60 110 160 240 330 450 580 660 950 1300 2500 4000 5200 6500-7800 15000 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings
More informationPressure relief valve, direct operated. Type DBD..K. Contents. Features. RE Edition:
Pressure relief valve, direct operated Type DBD..K RE 25715 Edition: 2015-06 Size 2 Component series 2X Maximum operating pressure 420 bar Maximum flow 2 l/min H8070 Features Screw-in cartridge valve 6
More informationFREUDENBERG XPRESS CUSTOM-MANUFACTURED SEALS
FREUDENBERG XPRESS FREUDENBERG XPRESS CUSTOM-MANUFACTURED SEALS In today s economic environment Freudenberg Xpress is the clear solution for companies needing precise and speedy results. Short turnaround,
More informationInstallation and commissioning of Settima screw pumps. Type GR** SMT** 3-screw screw pumps. a. Medium:
Settima screw a. Medium: HL oil conforming to DIN 51524 Parts 2 and 3 Special media such as: HFA min 5% oil HFB min 40% oil HFC max. 35-55% water HFDR high-viscosity lubricants SKYDROL, MIL-H may also
More informationPressure relief valve, pilot operated
Pressure relief valve, pilot operated RE 64605/03.09 /8 Type MHDBV (high-performance) Sizes 6 and Component series 3X Maximum operating pressure 40 bar Maximum flow 40 l/min H7567 Table of contents Contents
More informationMerkel PTFE U-rings. for high level applications
Merkel PTFE U-rings for high level applications Product information Merkel PTFE U-rings Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global Technology Specialist
More informationTranseals Pty Ltd. Phone 61 (8) Fax 61 (8) Web
Phone 61 (8) 9451 6011 Fax 61 (8) 9458 5766 Web http://www.transeals.com.au Email seals@transeals.com.au ABN 29 008 902 163 1 Atlas Court, Welshpool, Western Australia, 6106 PO Box 15, Welshpool, Western
More informationfor Seals and Vibration Control
Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global Technology Specialist for Seals and Vibration Control offers you a complete service package. A unique range
More informationDICHTOMATIK. Bonded Seals US/USS
DICHTOMATIK Bonded Seals US/USS US/USS Bonded seals (US, USS) are metal washers with a trapezoidal elastomer sealing lip vulcanised to their inner diameter. Description Product group Type Sealing material
More informationReturn line filter for direct tank mounting Type ABZFR
RE 5 8/. Replaces: 7.99 Return line filter for direct tank mounting Type ABZFR Maximum operating pressure 5 bar Maximum flow 5 l/min H69+69.tif Return line filter type ABZFR Table of contents Contents
More informationHydraulic cylinders type CH - big bore sizes to ISO nominal pressure 16 MPa (160 bar) - max 25 MPa (250 bar)
www.atos.com Table B60-6/ Hydraulic cylinders type CH - big bore sizes to ISO 600- - nominal pressure 6 MPa (60 bar) - max 5 MPa (50 bar) SWC Cylinders Designer Software for assisted selection of Atos
More informationInline filter with filter element according to DIN 24550
Inline filter with filter element according to DIN 24550 RE 51421/07.11 Replaces: 12.10 1/16 Type 245LEN0040 to 400; 245LE0130, 0150 Size according to DIN 24550: 0040 to 0400 Additional sizes: 0130, 0150
More informationMINIRAIL Profiled miniature guideway
MINIRAIL Profiled miniature guideway Table of Contents 1 Product overview and technical informations MINIRAIL a range of high-precision products.... 2 MINIRAIL overview accuracy classes:.... 3 MINIRAIL
More information1.3 HIGH PRESSURE SERIES
1.3 HIGH PRESSURE SERIES content Ordering Code 1.3.1 High Pressure Series Technical Information 1.3.2 Specifications 1.3.3 Hydraulic Fluids 1.3.4 Viscosity Range 1.3.5 Temperature Range 1.3.6 Seals 1.3.7
More informationGENERAL INFORMATION HYDRAULIC MOTORS ITALY
GENERAL INFORMATION INTERMOT produces RADIAL PISTON since 1985: our yearly production is more than 13.000 units which we sell all over the world through our agents and authorized sellers. Our motor range
More informationLine filter with filter element according to DIN 24550
Line filter with filter element according to DIN 2455 RE 51423/9.12 Replaces: 7.1 1/2 Type 445LEN4 to 1 Size according to DIN 2455: 4 to 1 Nominal pressure: 45 bar [6527 psi] Connection up to G 1 1/2;
More informationChange-Over Inline Filter AFLD to API 614
Change-Over Inline Filter to API 614 up to 17 l/min, up to 4 bar 112/ 113 122/ 123 232/ 233 242/243 332/333 52/53 542/543 882/883 142/143 272/273 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction
More informationReturn Line Filter HF4R up to 450 l/min, up to 10 bar
Return Line Filter HF4R up to 450 l/min, up to 10 bar 9" 18" 27" 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed in accordance with international regulations.
More informationReturn Line Filter RFM with 4-Hole Mounting
Return Line Filter with 4-Hole Mounting Tank-top mounted versions: up to 850 l/min, up to 10 bar 75 90 150 165 185 210 270 330 500 600 661 851 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction
More informationInline filter with filter element according to DIN 24550
Inline filter with filter element according to DIN 24550 RE 51422/07.11 Replaces: 12.10 1/18 Type 350LEN0040 to 1000; 350LE0130, 0150 Size according to DIN 24550: 0040 to 1000 Additional sizes: 0130, 0150
More informationDICHTOMATIK. Hydraulic seals
Titel Hydraulik 2008 GB:Titel 2008 10.09.2008 17:08 Uhr Seite 2 DICHTOMATIK Hydraulic seals DICHTOMATIK Hydraulic seals Albert-Schweitzer-Ring 1 D-22045 Hamburg P.O. Box 70 04 80 D-22004 Hamburg Phone
More informationDICHTOMATIK Sealing mechanism
DICHTOMATIK Sealing mechanism Static tightness on the outer surface The primary task of the outer surface of the rotary shaft seal is to ensure static tightness in the housing bore, i.e. the passage of
More informationBlock mounting filter, for lateral flange-mounting
Block mounting filter, for lateral flange-mounting RE 51419/2.1 1/18 Type 35PSFN4 to 1; 35PSF13, 15 Size according to DIN 2455: 4 to 1 Additional sizes: 13, 15 Nominal pressure 35 bar [579 psi] Port up
More informationPressure reducing valve, pilot operated
Pressure reducing valve, pilot operated RE 685/.5 Replaces:. /6 Type DR K Size Component series X Maximum operating pressure 5 bar Maximum flow l/min K478/7 Table of contents Contents Page Features Ordering
More informationBlock mounting filter, for lateral flange-mounting
Block mounting filter, for lateral flange-mounting RE 51418/12.1 Replaces: 1.1 1/18 Type 245PSFN4 to 4; 245PSF13, 15 Size according to DIN 2455: 4 to 4 Additional sizes: 13, 15 Nominal pressure 25 bar
More informationV-Rings around the clock... around the clock...
Description V-rings are rotary seals that can perform numerous jobs in their function of sealing rotating shafts: sealing against the penetration of dirt, dust, water or watery pollutants, combination
More informationChange-Over Pressure Filter DFDK
Change-Over Pressure Filter up to 2500 l/min, up to 315 bar 30 60 110 140 160 240 280 330 500 660 1.x 660 2.x 990 2.x 1320 2.x 1320 3.x 2640 3.x 3960 3.x 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING
More informationBlock mounting filter, for vertical flange-mounting
Block mounting filter, for vertical flange-mounting RE 51417/12.1 Replaces: 7.1 1/18 Type 45PBFN4 to 1; 45PBF13, 15 Size according to DIN 2455: 4 to 1 Additional sizes: 13, 15 Nominal pressure 45 bar [653
More informationInline Filter RFL. Cast version Volume rates up to 1300 l/min* Pressure range 25/40 bar
RFL inline filters are designed for inline mounting in hydraulic and lubrication systems. Inline Filter RFL Cast version Volume rates up to 1300 l/min* Pressure range 25/40 bar * For larger flow rates,
More informationBlock mounting filter, for sandwich plate mounting
Block mounting filter, for sandwich plate mounting RE 51427/01.11 1/16 Type 320PZR025, 075, 125 Size according to DIN 24550: 025 to 125 Nominal pressure 320 bar [4641 psi] Port according to ISO4401 size
More informationChange-Over Inline Filter RFLD Welded Version
Change-Over Inline Filter RFLD Welded Version up to 15000 l/min, up to 16 bar RFLD 1300 CAS to RFLD 15000 CBW 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed
More informationAccumulator shut-off block. Type ABZSS. Contents. RE Edition: Replaces: 05.13
Accumulator shut-off block Type ABZSS RE 011 Edition: 2016-07 Replaces: 0.1 Nominal diameter DN08; DN10; DN20; DN0 Component series X Maximum operating pressure 0 bar [07 psi] HAD8066 Contents Features
More informationInline filter with filter element according to DIN 24550
Inline filter with filter element according to DIN 24550 RE 51448/06.11 Replaces: RE 51400 1/18 Type 110LEN0040 to 0400; 110LE0130, 0150 Size according to DIN 24550: 0040 to 0400 Additional sizes: 0130,
More informationInline Filter LPF D A Flange-Mounted up to 280 l/min, up to 25 bar
Inline Filter LPF D A Flange-Mounted up to 280 l/min, up to 25 bar 160 240 260 280 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed in accordance with international
More informationPiston Accumulators High pressure
Piston Accumulators High pressure 1. DESCRIPTION 1.1. FUNCTION Fluids are practically incompressible and cannot therefore store pressure energy. The compressibility of a gas is utilised in hydraulic accumulators
More informationPiston Accumulators High pressure
Piston Accumulators High pressure 1. DESCRIPTION 1.1. FUNCTION Fluids are practically incompressible and cannot therefore store pressure energy. The compressibility of a gas is utilised in hydraulic accumulators
More informationStatic and dynamic oil compatibility tests for Freudenberg radial shaft seals to release the usage in FLENDER-gear units applications (Table T 7300)
- Page of 8 Test Documentation This document is a translation of Freudenberg Sealing Technologies (FST) internal test procedure FB 7 008. In case both documents contradict each other, the iginal German
More informationPressure relief valve, pilot-operated. Type ZDB and Z2DB. Contents. Features. RE Edition: Replaces: 05.11
Pressure relief valve, pilot-operated Type ZDB and ZDB RE 576 Edition: 06- Replaces: 05. Size 0 Component series 4X Maximum operating pressure 35bar [4600 psi] Maximum flow 00 l/min [6.4 US gpm] H7747
More informationSeals for Fluid Power. Catalog Seals for Fluid Power. Y o u r T e c h n o l o g y S p e c i a l i s t
Seals for Fluid Power Freudenberg Group Seals for Fluid Power Catalog 2007 Y o u r T e c h n o l o g y S p e c i a l i s t The information in this product catalog is based on the experience gained in decades
More informationPS-SEAL PTFE based high-performance seals
Garlock PS-SEAL PTFE based high-performance seals PS-SEAL Contents Introduction and advantages.............. 2 Technical data............................ 3 + 4 PS Standard/PS Non Standard.............
More informationReturn line and Suction Boost Filter RKM
Return line and Suction Boost Filter up to 850 l/min, up to 10 bar 80 100 120 151 201 251 201/-TH 300 350 400 800 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed
More informationP54 PISTON SEAL TECHNICAL DETAILS. Part Number Structure. Double-Acting F E A T U R E S P54 M R N HLX. Compact piston design.
PISTON SEAL Double-Acting TECHNICAL DETAILS The Hallite P54 is a double-acting, o-ring energized, low-friction piston seal that performs well in both high- and low-pressure systems. High-performance Armorlene
More informationW SERIES TECHNICAL CATALOGUE
WHEEL MOTOR W SERIES TECHNICAL CATALOGUE W 05 INDEX GENERAL INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Pag. 2 W 05 G100 (Fixed displacement) (SIZE AND TECHNICAL DATA) -
More informationInline filter. Features RE 51401/ Types 40 FLEN 0160 to 1000; 40 FLE 0045, 0055, 0120 to 0270
Inline filter RE 5101/08.08 1/10 Types 0 FLEN 0160 to 1000; 0 FLE 005, 0055, 010 to 070 Nominal size according to DIN 550: 0160 to 1000 Nominal size according to BRFS: 005, 0055, 010 to 070 Nominal pressure
More informationReturn Line Filter RF
HYDAC return line filters type RF are designed to be mounted directly on tank tops. Inline mounting is also possible. Return Line Filter RF Flow rates up to 5, l/min Pressure range up to 25 bar Material:
More informationPressure Filter DF Pressure Filter for Reversible Oil Flow DFF/DFFX
Pressure Filter DF Pressure Filter for Reversible Oil Flow DFF/DFFX up to 2000 l/min, up to 420 bar DF/DFF...1.X/2.X 30 60 110 140 160 240 280 330 500 660 990 1320 1500 2000 3000 4000 DF...3.X DFFX...1.X/2.X
More informationUPN. Rod and piston seal with energizing element UPN
Rod and piston seal with energizing element MATERIAL 1 1 Type Polyurethane Designation SEALPUR 93 Hardness 93 ShA 2 2 Type Nitril Rubber NBR Designation RUBSEAL 70 Hardness 70 ShA Pressure 400 bar FIELD
More information