Submittal Transmittal

Transcription

1 Submittal Transmittal Standard St. Joe's - Sonntag Pavillion St. Joseph s Hospital 350 W. Thomas Road Phoenix, AZ Project # 5690A Tel: Fax: Kitchell Contractors Inc of AZ Date: 9/2/2011 Reference Number: 0107 To: Chris Khas Walters & Wolf Construction Specialties Inc 889 N. Colorado St. Gilbert, AZ Tel: (480) Fax: (480) From: David Brown Kitchell Contractors Inc of AZ 1707 E Highland Ave, Suite 190 Phoenix, AZ Tel: (602) Fax: (602) Transmitted For Delivered Via Tracking Number Revise & Resubmit Submittal Package No Qty Description Due Date Package Action Door Hardware 9/13/2011 OPEN Items Qty Description Item Action 1 1 Hardware Schedule OPEN 2 1 Hardware Cut Sheets OPEN 3 1 Locksets OPEN Cc: Company Name Contact Name Copies Remarks Revise and Resubmit based on revised hardware. Signature Signed Date Prolog Manager Printed on: 9/2/2011 KCI_Production_Standardized Page 1 of 1

2 Submittal Transmittal Standard St. Joe's - Sonntag Pavillion St. Joseph s Hospital 350 W. Thomas Road Phoenix, AZ Project # 5690A Tel: Fax: Kitchell Contractors Inc of AZ Date: 8/11/2011 Reference Number: 0015 To: Tracy Lee Orcutt Winslow 3003 N Central Ave Phoenix, AZ Tel: (602) Fax: (602) From: David Brown Kitchell Contractors Inc of AZ 1707 E Highland Ave, Suite 190 Phoenix, AZ Tel: (602) Fax: (602) Transmitted For Delivered Via Tracking Number Approval Submittal Package No Qty Description Due Date Package Action Door Hardware 8/26/2011 OPEN Items Qty Description Item Action 1 1 Hardware Schedule OPEN 2 1 Hardware Cut Sheets OPEN 3 1 Locksets OPEN Cc: Company Name Contact Name Copies Remarks Please review the attached Hardware Submittal. Signature Signed Date Prolog Manager Printed on: 8/11/2011 KCI_Production_Standardized Page 1 of 1

3 SET #HW-1 DR# D-1 2 Continuous Hinge MCK-25HD x EPT 628 MC 2 Power Transfer EPT 626 SN 1 Exit Device ELR-LS26LD x 2000C 26D PR 1 Exit Device LS-26LD 26D PR 1 Rim Cylinder 1E BE 1 Automatic Operator GT710 x On/Off toggle (active leaf only) 689 HO 2 Actuators Recessed Square Push Plates 630 HO 1 Closer UNI-J8501 (in-active leaf) 689 NO 2 Floor Stop 481 x EXP 626 RO 2 Door Sweep 315 CN PE 1 Threshold 271 A PE 1 Power Supply ELR-150 PR 1 Card Reader NOTE: Weatherseal shall be an integral part of the aluminum framing system. NOTE: Card reader, power supply, conduit, wiring, test and termination shall be provided and installed by the security contractor. SET #HW-2 DR# D-5 1 Continuous Hinge MCK-25HD x EPT 628 MC 1 Power Transfer EPT 626 SN 1 Exit Device ELR-24LD x 2000C 26D PR 1 Rim Cylinder 1E BE 1 Automatic Operator GT710 x On/Off toggle (active leaf only) 689 HO 2 Actuators Recessed Square Push Plates 630 HO 1 Floor Stop 481 x EXP 626 RO 1 Door Sweep 315 CN PE 1 Threshold 271 A PE 1 Power Supply ELR-150 PR 1 Card Reader NOTE: Weatherseal shall be an integral part of the aluminum framing system. NOTE: Card reader, power supply, conduit, wiring, test and termination shall be provided and installed by the security contractor. SET #HW-3 DR# D-7 3 Hinges T4A3786 NRP 26D MC 1 Electric Transfer Hinge T4A3786 CC8 26D MC 1 Electrified Lockset 93KW7DEU15DS3 26D SA 1 Closer NO 1 Protection Plate K " x 2" LDW 630 RO 1 Wall Stop RO 1 Weatherstrip 305 CR H & J PE 1 Door Shoe 222 AV PE O W #2010_

4 1 Threshold 271 A PE 1 Raindrip 346 C DR Width + 4" PE 1 Power Supply 1 Card Reader NOTE: Card reader, power supply, conduit, wiring, test and termination shall be provided and installed by the security contractor. SET #HW-4 DR# D-4 3 Hinges T4A3786 NRP 26D MC 1 Electric Transfer Hinge T4A3786 CC8 26D MC 1 Electrified Lockset 93KW7DEU15DS3 26D SA 1 Closer PR NO 1 Protection Plate K " x 2" LDW 630 RO 1 Wall Stop RO 1 Seal S88 D BLK PE 1 Power Supply 1 Card Reader NOTE: Card reader, power supply, conduit, wiring, test and termination shall be provided and installed by the security contractor. SET #HW-5 DR# D-2 8 Hinges T4A3786 NRP 26D MC 2 Push Plates 70F 8 x RO 2 Pull Plates 110 x 70C 4 x RO 2 Closer CLP8501H 689 NO 2 Protection Plate K " x 1" LDW 630 RO 2 Silencers 608 GRY RO SET #HW-6 DR# D-3, D-6 3 Hinges T4A3786 NRP 26D MC 1 Electric Transfer Hinge T4A3786 CC8 26D MC 1 Electrified Lockset 93KW7DEU15DS3 26D SA 1 Protection Plate K " x 2" LDW 630 RO 1 Wall Stop RO 3 Silencers 608 GRY RO 1 Power Supply 1 Card Reader NOTE: Card reader, power supply, conduit, wiring, test and termination shall be provided and installed by the security contractor. END OF SECTION O W #2010_

5 Construction Specialties 889 N. Colorado St. Gilbert, AZ ph: 480/ fax: 480/ Door, Frame & Hardware Submittal For: SONNTAG PAVILION 350 W. THOMAS PHOENIX, AZ Contractor: KITCHELL CONTRACTORS 1707 E. HIGHLAND #100 PHOENIX, AZ ph: (602) fax: Architect: Orcutt Winslow 3003 North Central Ave Phoenix, AZ ph: (602) fax: (602) Walters & Wolf Project Information Project Manager: Patrick Kanavel Field Superintendent: Jeff Aglialoro cell: Job # : JL-143 AZ Lic ROC / ROC212069, NM Lic. ROC89459

6 Manufacturer's List Mfr. Hardware Used Rockwood Door Stop, Kickplate, Wall Stop, Push Plate, Pull Plate Norton Hager Pemko Best Access Systems Precision Hardware Inc Stanley Security Solutions Inc. Surface Closer Continuous Hinge, Hinge Sweep, Threshold, Gasketing, Door Bottom, Rain Guard Cylindrical Lock Concealed Vert Rod Exit, Rim Exit Device Cylinder

7 DOOR INDEX Project ID: JL-143 Sonntage Pavilion Door Number Arch Mark Item Number Heading # Keying Hand D-1 D RHRA/LHR D-2 D RHRA/LHR D-3 D RH D-4 D LHR D-5 D LHR D-6 D RHR D-7 D RH Walters & Wolf Construction Specialties Page 6 of 8 7/27/2011 4:44:14 PM

8 Hardware Schedule Project ID: JL-143 Sonntage Pavilion Heading #: 1 1 SGL Door: D-1 EXTERIOR FROM VESTIBULE RHRA/LHR 0" x 0" x 1 3/4" ALD/ALF 2 EA Continuous Hinge HD 119" Clear (HC-1) Hager 1 EA Concealed Vert Rod Exit 2608 CD 2908A 630 (ED-1) Precision Hardware Inc 1 EA Concealed Vert Rod Exit 2601 CD (ED-3) Precision Hardware Inc 1 EA Cylinder 1E (CY-1) Stanley Security Solutions Inc. 2 EA Cylinder 1E (CY-2) Stanley Security Solutions Inc. 1 EA Surface Closer UNIJ (CL-1) Norton 2 EA Door Stop 481 EXP US26D (ST-1) Rockwood 1 EA Threshold 271A x 6' (TH-1) Pemko 2 EA Sweep 315CN x 3' (SW-1) Pemko Heading #: 2 1 SGL Door: D-5 EXTERIOR FROM CONF. ROOM LHR 0" x 0" x 1 3/4" ALD/ALF 1 EA Continuous Hinge HD 95" Clear (HC-2) Hager 1 EA Rim Exit Device 2408 CD 2908A 630 (ED-2) Precision Hardware Inc 1 EA Cylinder 1E (CY-1) Stanley Security Solutions Inc. 1 EA Cylinder 1E (CY-2) Stanley Security Solutions Inc. 1 EA Door Stop 481 EXP US26D (ST-1) Rockwood 1 EA Threshold 271A x 6' (TH-1) Pemko 1 EA Sweep 315CN x 3' (SW-1) Pemko Heading #: 3 1 SGL Door: D-7 CORRIDOR TO CATERING RH 3' 0" x 8' 0" x 1 3/4" HMD/HMF 4 EA Hinge ECBB1102NRP 4-1/2" x 4-1/2" US26D (HI-1) Hager 1 EA Cylindrical Lock 93K7R 15D S3 626 (LO-1) Best Access Systems 1 EA Surface Closer (CL-3) Norton 1 EA Kickplate K " x 34" US32D (KP-1) Rockwood 1 EA Wall Stop 403 US26D (ST-2) Rockwood 1 EA Threshold 271A x 3' (TH-2) Pemko 1 EA Gasketing 305CR x 19' (GA-1) Pemko 1 EA Rain Guard 346C x 3' 4" (GA-2) Pemko 1 EA Door Bottom 222AV x 3' (DB-1) Pemko Heading #: 4 1 SGL Door: D-4 CORRIDOR FROM CONF. ROOM LHR 90 Min 3' 0" x 8' 0" x 1 3/4" WDD/HMF 4 EA Hinge ECBB1102NRP 4-1/2" x 4-1/2" US26D (HI-1) Hager 1 EA Cylindrical Lock 93K7R 15D S3 626 (LO-1) Best Access Systems 1 EA Surface Closer PR (CL-2) Norton 1 EA Kickplate K " x 34" US32D (KP-1) Rockwood 1 EA Wall Stop 403 US26D (ST-2) Rockwood 1 EA Gasketing S88D 20' (GA-3) Pemko Walters & Wolf Construction Specialties Page 7 of 8 7/27/2011 4:44:14 PM

9 Hardware Schedule Project ID: JL-143 Sonntage Pavilion Heading #: 5 1 PR Door: D-2 VESTIBULE FROM CONF. ROOM RHRA/LHR 2-3' 0" x 8' 0" x 1 3/4" WDD/HMF 8 EA Hinge ECBB1102NRP 4-1/2" x 4-1/2" US26D (HI-1) Hager 2 EA Push Plate 70F US32D (PP-1) Rockwood 2 EA Pull Plate 110x70C US32D (PP-2) Rockwood 2 EA Surface Closer CLP8501T 689 (CL-4) Norton 2 EA Kickplate K " x 35" US32D (KP-2) Rockwood Heading #: 6 1 SGL Door: D-3 CONF. ROOM TO AV ROOM RH 1 SGL Door: D-6 CONF. ROOM FROM CATERING RHR 3' 0" x 8' 0" x 1 3/4" WDD/HMF 8 EA Hinge ECBB1100NRP 4-1/2" x 4-1/2" US26D (HI-2) Hager 2 EA Cylindrical Lock 93K7R 15D S3 626 (LO-1) Best Access Systems 2 EA Kickplate K " x 34" US32D (KP-1) Rockwood 2 EA Wall Stop 403 US26D (ST-2) Rockwood Walters & Wolf Construction Specialties Page 8 of 8 7/27/2011 4:44:14 PM

10 8000 Series Door Closers OVERVIEW Features Non-handed Staked valves Standard, separate and independent, latch, sweep and backcheck intensity valves Cast aluminum body Rack-and-pinion design 1-1/4" (32mm) diameter piston 5/8" (16mm) diameter pinion journals 2-1/8" (54mm) projection (standard covers) All standard arm applications (with slim, full or metal covers) allow doors to swing 180 degrees, conditions permitting 8300/ shipped with slim-line plastic cover 8500/ shipped with full plastic cover Full size template 10-year limited warranty Optional Features Metal, architectural plastic or architectural metal covers (8500 or 8501 only) Lead lined metal cover - suffix MLL Delayed action Heavy-duty arms; Regular Rigid, Parallel Rigid, CloserPlus, CloserPlus Spring, Unitrol Slide Tracks: push or pull side mounting Compliance Standards ANSI/BHMA A156.4, Grade 1 certified UL listed UL10C compliant for positive pressure ADA compliant (8301 and 8501) Features Sized springs 2, 3, 4, 5, 6 with 50% additional adjustment X X Adjustable spring sizes 1 through 6 X X Bi-pack packaging standard (regular arm and top jamb mounting) X X Tri-Style packaging standard (regular arm, top jamb and parallel arm mounting) X X TABLE OF CONTENTS Overview How to Order Fasteners/Finishes Features Optional Features Suggested Specifications Applications Technical Details Accessories Parts List /09

11 8000 Series Door Closers SUGGESTED SPECIFICATIONS 8301/8501 Series Closers for interior and exterior doors shall be full rack-and-pinion type with cast aluminum alloy shell. Closers shall be surface mounted and shall project no more than 2-1/8" from the surface of the door with standard cover. Closers shall be non-handed to permit installation on doors of either hand. Closer fluid shall contain lubricity and anti-oxidation agents. Closer fluid shall maintain stable viscosity to allow door closer to perform in temperatures ranging from extremely high to as low as -40 F. Closers shall have multi-size spring power adjustment to permit setting of spring from size 1 through size 6. Closers shall have two non-critical valves, hex key adjusted, to independently regulate sweep speed and latch speed. Closers shall have adjustable backcheck intensity controlled by a hex key adjusted valve. [Closers shall have adjustable delayed action closing controlled by a hex key adjustable valve.] Regular arm and top jamb closers shall have a non-hold open shoe permitting 15% ( + or 7-1/2% ) power adjustment. **Closers shall be enclosed in a [molded resin cover] [plated or sprayed metal cover], Closers to be Norton [8301/8501] [8501M] [8501MA] [8501A]. **For special arms insert that specification here (see column three on this page). 8300/8500 Series Closers for interior and exterior doors shall be full rack-and-pinion type with cast aluminum alloy shell. Closers shall be surface mounted and shall project no more than 2-1/8" from the surface of the door with standard cover. Closers shall be non-handed to permit installation of doors of either hand. Closer fluid shall contain lubricity and anti-oxidation agents. Closer fluid shall maintain stable viscosity to allow door closer to perform in temperatures ranging from extremely high to as low as -40 F. Closers shall have power adjustment to permit a 50% increase in power over the minimum closing force for any size. Closers shall have two non-critical valves, hex key adjusted, to independently regulate sweep speed and latch speed. Closers shall have adjustable backcheck intensity controlled by a hex key adjusted valve. [Closers shall have adjustable delayed action closing controlled by a hex key adjustable valve.] Regular arm and top jamb closers shall have a non-hold open shoe permitting 15% (+ or 7-1/2%) power adjustment.** Closers shall be enclosed in a [molded resin cover] [plated or sprayed metal cover], Closers to be Norton [8300/8500] [8500M] [8500A] [8500MA]. **For special arms insert that specification here (see column three on this page). **Unitrol Arm Door closers shall have a fixed door stop feature effective at one point selected at installation, from in fivedegree increments. Door stop shall be cushioned by a shock-absorbing heavyduty spring action effective at the [soffit plate] [arm shoe] pivot. [Closers shall be provided for parallel arm installation using a rigid steel main arm and secondary arm lengths proportional to the door width.] [Closers shall be provided for top jamb installation using a forged steel, rigid main arm and telescoping secondary arm adequate for the frame reveal of the openings.] **CloserPlus Arm Door closers shall have a field reversible door stop. Door closer shall have a feature with selectable on and off ball and detent hold open. Hold open tension shall be adjustable effective at one point selected at installation, from in five degree increments. [Hold open mechanism shall have engage/disengage selection actuated by thumbturn]. Closers shall be provided for parallel arm installation using a forged rigid steel main arm and secondary arm. **CloserPlus Spring Arm Door closers shall have built-in door stop [and holder] effective at one point selected at installation, from in five-degree increments. Door stop mechanism shall be reversible and have a buffer spring that engages prior to the dead stop feature, reducing shock loads to the door and frame assembly. Door stop mechanism shall be non-handed and attached to soffit plate. [Hold open mechanism shall have engage/disengage selection actuated by thumbturn]. Closers shall be provided for parallel installation using a forged rigid steel main arm and secondary arm /09

12 Roton Continuous Geared Hinges Concealed Leaf Door of any Material - Standard and Heavy Duty " Thick Doors Standard Duty for medium frequency doors. Heavy Duty for high frequency doors or heavy medium frequency doors. Door of any Material - Standard and Heavy Duty - 2" Thick Doors or Greater Standard Duty for medium frequency doors. Heavy Duty for high frequency doors or heavy medium frequency doors HD LL HD LL Clearance: Fasteners: Length Options: Door Reinforcement: Frame Reinforcement: Fire Rating: Special Features: 5 /16" (8 mm) hinge side plus standard lockside clearance Dril-Kwik screws Standard and Custom None required to 200 lbs. Heavier weight use 16 gauge channel None required to 200 lbs. Heavier weight use 16 gauge channel Up to 3 hr. metal and 90 min. wood composite (with studs) Lead lined model for hospital x-ray room doors with double row of screws to straddle lead (Specify LL ) Door edge protection lip Frame leaf alignment rib for proper hinge and door location 3 /32" (2 mm) inset Clearance: Fasteners: Length Options: Door Reinforcement: Frame Reinforcement: Fire Rating: Special Features: 5/16" (8 mm) hinge side plus standard lockside clearance Dril-Kwik screws Standard and Custom None required to 200 lbs. Heavier weight use 16 gauge channel None required to 200 lbs. Heavier weight use 16 gauge channel Up to 3 hr. metal and 90 min. wood composite (with studs) Lead lined model for hospital x-ray room doors with double row of screws to straddle lead (Specify LL ) Frame and door leaf alignment ribs for proper hinge and door location Hinge Length - Inches Hinge Length - cm Std Door Screws HD LL Std Jamb Screws HD LL Hinge Length - Inches Hinge Length - cm Std Door Screws HD LL Std Jamb Screws HD LL OPENING 0 OPENING 25/32" (20 mm) 25/32" (20 mm) 21/32" (17 mm) 3/32" (2 mm) 21/32" (17 mm) 1-15/16" (49 mm) 5/16" (8 mm) 1-3/4" (49 mm) 1-15/16" 5/16" (49 mm) (8 mm) 2" (51 mm) 1/16" (1.5 mm) 1/16" (1.5 mm) 1/32" (1 mm) 1/16" (1.5 mm) 1/8" (3.2 mm) 1/16" (1.5 mm)

13 Architectural Hinges Full Mortise - ECCO Five Knuckle Plain Bearing - Standard Weight For use on medium weight doors or doors requiring low frequency service EC1100 Steel with Steel pin - ANSI A8133 EC1100 Steel with Steel pin NRP - ANSI A8133 EC1101 Stainless Steel with Stainless Steel pin - ANSI A5133 Non-rising removable pin with button tip and plug With door closer use ball bearing hinge Hinge Size Gauge of Hole Screw Size Inches mm Metal Count Machine Wood 4 1 /2 x4 1 /2 114 x /2 x /4 x12 Plain Bearing - Standard Weight For use on medium weight doors or doors requiring low frequency service ECRC1100 Steel with Steel pin - ANSI A8133 Non-rising removable pin with button tip and plug Round corner with 1 /4" radius standard With door closer use ball bearing hinge Hinge Size Gauge of Hole Screw Size Inches mm Metal Count Machine Wood 4x4 102 x /2 x /4 x12 Ball Bearing - Standard Weight For use on medium weight doors or doors requiring medium frequency service ECBB1100 Steel with Steel pin - ANSI A8133 ECBB1100 Steel with Steel pin NRP - ANSI A8133 ECBB1101 Brass with Stainless Steel pin - ANSI A5112 Stainless Steel with Stainless Steel pin - ANSI A2112 ECBB1101 Brass with Stainless Steel pin NRP - ANSI A5112 Stainless Steel with Stainless Steel pin - ANSI A2112 Two ball bearings Non-rising removable pin with button tip and plug Five Knuckle Ball Bearing - Standard Weight For use on medium weight doors or doors requiring medium frequency service ECRCBB1100 Steel with Steel pin - ANSI A8112 Two ball bearings Non-rising removable pin with button tip and plug Round corner with 1 /4" radius standard Hinge Size Gauge of Hole Screw Size Inches mm Metal Count Machine Wood 4x4 102 x /2 x /4 x12 Ball Bearing - Heavy Weight For use on heavy weight doors or doors requiring high frequency service ECBB1102 Steel with Steel pin - ANSI A8111 ECBB1102 Steel with Steel pin NRP - ANSI A8111 ECBB1103 Brass with Stainless Steel pin - ANSI A5111 Stainless Steel with Stainless Steel pin - ANSI A2111 ECBB1103 Brass with Stainless Steel pin NRP - ANSI A5111 Stainless Steel with Stainless Steel pin - ANSI A2111 Four ball bearings Non-rising removable pin with button tip and plug Hinge Size Gauge of Hole Screw Size Inches mm Metal Count Machine Wood 4 1 /2 x4 1 /2 114 x /2 x /4 x12 5x4 1 /2 127 x /2 x /4 x12 Hinge Size Gauge of Hole Screw Size Inches mm Metal Count Machine Wood 4 1 /2 x4 114 x /2 x /4 x /2 x4 1 /2 114 x /2 x /4 x

14 DOOR BOTTOMS Specialty Door Bottoms May be used in many different applications. Some of these shapes may be used as meeting stile gasketing, see page 76 for examples. 313_N A, D, G 313_P A 317_N A, D, G 317_N in alternate position. 317_P A 314_N C, D, G 318_V A, BDG, D, G, PW 3185_V A, D DOOR BOTTOMS Door Top Weatherstrip _343 PA AVAILABLE LENGTHS: 36", 48" For top of 1-3/8" wood doors. _344 B, PA AVAILABLE LENGTHS: 36", 48" For top of 1-3/4 wood doors. 377P pile seal 377V vinyl seal Rigid tan colored vinyl with vinyl (V) insert or pile (P) insert used as a door top (or bottom) filler strip for hollow metal doors. 346_ C, D, G, PW Note: Diagram consists of two parts, each sold separately. Overhead rain drip with slotted holes. Should be ordered a minimum of 4" longer than the door width. 347_ 68_R A, D, G 347 is the raindrip and hook. 68_R is the interlock. For outswing doors only. Should be ordered a minimum of 4" longer than the door width. AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart) A (Mill Finish Aluminum) B (Mill Finish Extruded Bronze[Brass]) BDG (Bright Dip Gold Anodized) C (Clear Anodized) D (Dark Bronze Anodized) G (Gold Anodized) PA (Painted Aluminum) PW (Painted White) DB

15 PERIMETER GASKETING Adhesive Perimeter Gasketing For more information on these perimeter gasketing products, please see the Adhesive Gasketing section. S773_ D, GR, W AVAILABLE LENGTHS: 17', 18', 20', 21', 25' S88_ BL, C, D, GR, TAN, W AVAILABLE LENGTHS: 17', 18', 20', 21', 25', 30', 204', 510' S44_ BL, D, W AVAILABLE LENGTHS: 17', 18', 20', 21', 25', 510' Triple-fin design effectively blocks light and sound from infiltrating a room. Product designed as hospitality gasketing (see more hospitality products in the Hospitality Products section). Seal begins compressing at 1/4"; compresses to seal up to a 1/16" gap. Designed for tighter frames. Demonstrates extremely low closing force. Seal begins compressing at 5/16"; compresses to seal up to a 1/16" gap. S77_ C, D, W AVAILABLE LENGTHS: 17', 18', 20', 21', 25' PK33_ BL, D, W 17', 18', 20', 21', 25', 510' PK55_ BL, D, W 17', 18', 20', 21', 25', 510' PERIMETER GASKETING Designed for hollow metal and wood meeting stile applications. Seal begins compressing at 5/16"; com presses to seal up to a 1/16" gap. Magnetic Designed for tighter frames. Demonstrates extremely low closing force. Seal begins compressing at 3/16"; com presses to seal up to a 1/16" gap. Designed for tighter frames. Demonstrates extremely low closing force. Seal begins compressing at 3/16"; compresses to seal up to a 1/16" gap. NOTES FOR ALL ADHESIVE GASKETING: Storage and shelf life: All adhesive gaskets have a limited shelf life. This product must be used within 6 months of purchase and must be stored between 50 O F and 100 O F. For further notes/details, please see Adhesive Gasketing section. 2815_M C, D, G NOTE: Products shown in this section may not be drawn to scale. AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart) C (Clear Anodized) D (Dark Bronze Anodized) G (Gold Anodized) Adhesive Gasketing Colors: BL (Black) C (Clear) D (Dark Brown) GR (Light Gray) TAN (Tan) W (White) VENTURA, CA USA PH MEMPHIS, TN USA PH VANCOUVER, BC CANADA PH TORONTO, ON CANADA PH PG-10

16 DOOR BOTTOMS Door Bottom Sweeps 368_N C, D, G 315_N B, C, D, G, SN Finished product supplied with BLACK insert. GRAY available upon request. 315SSN AVAILABLE FINISH: SS (#4 Finish) 321SSN AVAILABLE FINISH: SS (#4 Finish) (23.8) 321_N C, D, G 56_V A, BDG, D, G, PW, SN 57_V A, BDG, D, G, PW, SN 99_V PA, PD, PG, PW 307_V A, BDG, D, G, PW, SN DOOR BOTTOMS 308_V A, BDG, D, G, PW, SN 3452_V A, BDG, C, D, G, PW, SN 345_V A, BDG, D, G, PW 345_ A, B, BDG, C, D, G, PW 309_P A, BDG, D, G, PW, SN (14.3) NOTE: Products shown in this section may not be drawn to scale. AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart) A (Mill Finish Aluminum) B (Mill Finish Extruded Bronze [Brass]) BDG (Bright Dip Gold Anodized) C (Clear Anodized) D (Dark Bronze Anodized) G (Gold Anodized) PA (Painted Aluminum) PD (Painted Dark Bronze) PG (Painted Gold) PW (Painted White) SN (Satin Nickel Anodized) SS (See Individual Part)) DB

17 COMMERCIAL THRESHOLDS Saddle Thresholds To use a saddle threshold in an offset condition, use an elevator (see page 37). 173_ A, B, D, G COMMERCIAL THRESHOLDS 151_ A, B, D, G 270_ A, B, D, G 271_ A, B, D, G, SN 272_ A, B, D, G, SN 276_ A, B, D, G 2748_ A, D, G NOTE: Products shown in this section may not be drawn to scale. AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart) A (Mill Finish Aluminum) B (Mill Finish Extruded Bronze [Brass]) D (Dark Bronze Anodized) G (Gold Anodized) SN (Satin Nickel Anodized) NOTE: G, SN are available with limited inventory VENTURA, CA USA PH MEMPHIS, TN USA PH VANCOUVER, BC CANADA PH TORONTO, ON CANADA PH CT-2

18 DOOR BOTTOMS Door Shoes (Cont.) 222_V 222_PK A, D, G For hollow metal doors with inverted bottom channel. 2221_V 2221_PK A, D, G For hollow metal doors with inverted bottom channel. 221_V 221_PK A, D, G DOOR BOTTOMS 216_FG BDC, BDG, D, PW, SN Thermal Barrier Model Resin thermal break (FG) prevents conductivity of cold from exterior to interior. Combination door shoe and kick plate. Supplied with PemkoPrene Seal. Fabrication Options for Door Shoes 1/2 Full Notch Fabrication includes: removal of rain drip and front flange of door shoe to prevent interference with door stop and weatherstrip. Ordering: order width of door leaf, and designate by adding M following the product number. (Example: a 216AV with a 1/2" full notch fabrication, for a 36" door leaf = 216AVM36.) 1/2 Half Notch Fabrication includes: removal of rain drip to prevent interference with door stop and weatherstrip. Ordering: order width of door leaf and designate by adding N following the product number. Special: Other half notches available are 9/16, 5/8, and 3/4 widths, please specify when ordering. (Example: a 216AV with a 1/2" half notch fabrication, for a 36" door leaf = 216AVN36.) Combination door shoe and kick plate, with raindrip. 2211_V 2211_PK A, D, G AVAILABLE FINISHES FOR PRODUCTS SHOWN ON THIS PAGE (see General Information section for finish chart) A (Mill Finish Aluminum) BDC (Bright Dip Clear Anodized) BDG (Bright Dip Gold Anodized) D (Dark Bronze Anodized) G (Gold Anodized) PW (Painted White) DB

19 Push Plates Push Plates -.050" Thick Material: Finishes: Fastener: Features: Ordering: Options: Aluminum, Brass, Bronze, Stainless Steel Available in standard architectural finishes, US32DBIO, US32D316, US32316, and US3LIFETIME (see page 7). #6 x 5 8 OH SMS Four beveled edges. Specify plate number followed by size designation and finish; i.e., 70B US32D or for non-standard size 70 (width x height) and finish. Specify any additional optional features. Custom sizes available upon request. TEK - self-drilling screws. TORX - security torx screws. SA - self-adhesive mounting: 1 16" double face foam tape (no screw holes on plate). Engraving on plates 4" wide or wider. Specify copy. See page B1 for standard engraving locations. Cylinder Cutouts (CFC) and Turn Knob Cutouts (CFTT). See page B1 for standard locations and sizes. No. 70 No. 70A 70B 70C 70E 70F 70G Standard Size 3" x 12" 3 1 2" x 15" 4" x 16" 6" x 16" 8" x 16" 4" x 20" Weight 0.7 lbs. 0.9 lbs. 1.0 lbs. 1.5 lbs. 2.0 lbs. 1.3 lbs. ANSI A156.6 No. 70RC No. 70RCA 70RCB 70RCC 70RCE 70RCF 70RCG Standard Size 3" x 12" 3 1 2" x 15" 4" x 16" 6" x 16" 8" x 16" 4" x 20" Weight 0.7 lbs. 0.9 lbs. 1.0 lbs. 1.5 lbs. 2.0 lbs. 1.3 lbs. ANSI A156.6 No. 70RE No. 70REA 70REB 70REC Standard Size 3" x 12" 3 1 2" x 15" 4" x 16" Weight 0.7 lbs. 0.9 lbs. 1.0 lbs. ANSI A156.6 B2 Rockwood Manufacturing Company Phone: /08

20 Door Stops Door Stops No. 480, 481 Material: Finishes: Solid Cast Brass with DuraFlex Bumper Available in standard architectural finishes (see page 7). Features: Uses replacement bumper 461B. Heavy duty and ideal for use on heavy doors or in high traffic areas. Options: DuraFlex Bumper available in standard grey or optional black. Exterior Pack screw packs; stainless steel plated to match use EXP suffix (480 x EXP) when ordering. No. Fastener Base Height Weight ea. #12 x FH WS, 3 ea. plastic anchors 2 1 2" x1 3 4" 1 5 8" 5.8 lbs./ ea x 1 FH MS, 3 ea. lead anchors 2 1 2" x1 3 4" 1 5 8" 5.8 lbs./10 Door Stops No. 480H, 481H Material: Finishes: Solid Cast Brass with DuraFlex Bumper Available in standard architectural finishes (see page 7). Features: Uses replacement bumper 461B. Heavy duty and ideal for use on heavy doors or in high traffic areas. Options: DuraFlex Bumper available in standard grey or optional black. Exterior Pack screw packs; stainless steel plated to match use EXP suffix (480H x EXP) when ordering. No. Fastener Base Height Weight 480H 3 ea. #12 x FH WS, 3 ea. plastic anchors 2 1 2" x1 3 4" 2 1 4" 6.2 lbs./10 481H 3 ea x 1 FH MS, 3 ea. lead anchors 2 1 2" x1 3 4" 2 1 4" 6.2 lbs./10 6/08 D13 Rockwood Manufacturing Company Phone:

21 Wall Stops Solid Cast Wall Stops No. 400, 401, 402 Material: Finishes: Features: Cast Brass with DuraFlex Bumper Available in standard architectural finishes (see page 7). Concealed mounting, convex bumper. Back plate prevents damage to wall. ANSI No. Bumper Fastener Size Weight A Convex #6 x1 1 2 FH SMS, plastic toggle " dia., 3 4" projection 3.3 lbs./10 L Convex #8 x 1 RH WS, plastic anchor " dia., 3 4" projection 3.3 lbs./10 L Convex 8-32 x 1 TH MS, lead anchor " dia., 3 4" projection 3.3 lbs./10 L02101 Solid Cast Wall Stops No. 403, 404, 405 Material: Finishes: Features: Options: Cast Brass with DuraFlex Bumper Available in standard architectural finishes (see page 7). Concealed mounting, concave bumper. Back plate prevents damage to wall. DuraFlex Bumper available in standard grey or optional black. ANSI No. Bumper Fastener Size Weight A Concave #6 x1 1 2 FH SMS, plastic toggle " dia., 3 4" projection 3.3 lbs./10 L Concave #8 x 1 RH WS, plastic anchor " dia., 3 4" projection 3.3 lbs./10 L Concave 8-32 x 1 TH MS, lead anchor " dia., 3 4" projection 3.3 lbs./10 L /08 D1 Rockwood Manufacturing Company Phone:

22 Pull Plates Pull Plates No. 102 x 70, 105 x 70, 106 x 70, 107 x 70 Material: Finishes: Aluminum, Brass, Bronze, Stainless Steel Stocked in standard architectural finishes but available in any finish, US32DBIO, US32D316, and US32316 (see page 7). *US3LIFETIME available on select product below. Fastener: #6 x 5 8 OHSMS; x Thru Bolt & Finish Washer (standard 1 3 4" door). Options: Barrier Free available in 2 1 2" clearance use BF prefix when ordering (BF102 x 70C). Advise if door thickness is other than 1 3 4". See page B13 for mounting selection (standard duty ). No. 102 x 70B 102 x 70C 105 x 70B 105 x 70C 106 x 70B 106 x 70C 107 x 70B* 107 x 70C* Pull 5 8" dia. 5 8" dia. 3 4" dia. 3 4" dia. 3 4" dia. 3 4" dia. 3 4" dia. 3 4" dia. CTC 5 1 2" 5 1 2" 5 1 2" 5 1 2" 6" 6" 8" 8" Plate Size 3 1 2" x 15" 4" x 16" 3 1 2" x 15" 4" x 16" 3 1 2" x 15" 4" x 16" 3 1 2" x 15" 4" x 16" Weight 1.8 lbs. 1.9 lbs. 2.1 lbs. 2.2 lbs. 2.2 lbs. 2.3 lbs. 2.4 lbs. 2.5 lbs. ANSI A156.6 J405 J405 J405 J405 J405 J405 J405 J405 Pull Plates No. 110 x 70, 111 x 70 Material: Finishes: Aluminum, Brass, Bronze, Stainless Steel Stocked in standard architectural finishes but available in any finish, US32DBIO, US32D316, and US32316 (see page 7). *US3LIFETIME available on select product below. Fastener: #6 x 5 8 OHSMS; x Thru Bolt & Finish Washer (standard 1 3 4" door). Options: Barrier Free available in 2 1 2" clearance use BF prefix when ordering (BF110 x 70C). Advise if door thickness is other than 1 3 4". See page B13 for mounting selection (standard duty ). No. 110 x 70B 110 x 70C 111 x 70B* 111 x 70C* Pull 1" dia. 1" dia. 1" dia. 1" dia. CTC 8" 8" 10" 10" Plate Size 3 1 2" x 15" 4" x 16" 3 1 2" x 15" 4" x 16" Weight 3.8 lbs. 3.9 lbs. 4.3 lbs. 4.4 lbs. ANSI A156.6 J405 J405 J405 J405 6/08 B22 Rockwood Manufacturing Company Phone:

23 Door Plates Mop Plate Kick Plate Stretcher Plate Up to 8"h x 48"w 6" to 12"h x 48"w 6" to 12"h and up to 48"w Width of Plates: Push Side: 2" less than door width. Pull Side: 1 1 2" less than door width. NFPA 80 STANDARDS Protection Plates: Factory-installed protection plates shall be installed in accordance with the listing of the door. Field-installed protection plates shall be labeled and installed in accordance with their listing. Exception: Labeling is not required where the top of the protection plate is not more than 16 in. (406 mm) above the bottom of the door. Armor Plate Up to 48"h x 48"w and available in most finishes Self-Drilling TEK Screws Cuts Door Plate Installation Time in Half Metal Door Plate - Economy Duty No. K1038 Material: Finishes: Fastener: Ordering: Weight: Options:.038" Thick Aluminum, Stainless Steel Brass Look Aluminum (BRS LK), US32D, US32DPAT, and US3LIFETIME #6 x 5 8 TH SMS Specify height x width x finish code. Add any options. 8" x 34" = 3.2 lbs. SA - self-adhesive mounting. TEK - self-drilling screws. Cutouts for locks, louvers, or windows. TORX - security torx screws. US32DPAT Patterned Stainless Steel Metal Door Plate - Standard Duty No. K1050, K1050F Material:.050" Thick Aluminum, Brass, Bronze, Stainless Steel Finishes: Available in standard architectural finishes, US32DBIO, US32D316, and US32316 (see page 7). Fastener: #6 x 5 8 TH SMS Ordering: Specify height x width x finish code. Add any options. Weight: 8" x 34" = 4.0 lbs. ANSI: J101 - metal armor plate, J102 - metal kick plate, J103 - metal stretcher & mop plate. Options: SA - self-adhesive mounting. TEK - self-drilling screws. Beveled 3 or 4 edges, specify B3E or B4E. CSK - countersunk holes. Cutouts for locks, louvers, or windows. TORX - security torx screws. Screw mounting (K1050F) and UL listed for use on 90-minute label wood doors and 3-hour label metal doors. 6/08 C1 Rockwood Manufacturing Company Phone:

24 SAMPLE SPECIFICATIONS ACCEPTABLE MANUFACTURERS A. Locksets and Latchsets Stanley/BEST - No Substitution. 1. Locksets and latchsets: ANSI A156.2, Series 4000, Grade 1 UL listed, extra heavy-duty cylindrical type. 2. Backset 2 3 /4 inches (70mm) 3. Interchangeable core 7-pin: [Restricted keyway] [Patented] [Standard] [ ]. 4. Locksets to have anti-rotational studs that are through-bolted. 5. Keyed lever with no exposed keeper hole. 6. Each lever to have independent spring mechanism designed to control lever only. 7. Outside lever sleeve seamless, 1-piece construction, hardened steel alloy. 8. Keyed Lever: Removable only after core is removed, by authorized control key, to allow access to knob keeper. 9. Hub, side plate, anti-rotational studs 1-piece casting with shrouded locking lug. B. Keys and Keying A. Cylinders: 7-pin, interchangeable core and keyed into a [New] [Existing] factory registered Grand Masterkey System with a [Standard] [Restricted] [Patented] keyway. 1. Acceptable Material: Cylinders as manufactured by Stanley/BEST. B. Provide construction cores and keys during construction period. Construction control and operating keys and cores are not part of permanent keying system or furnished on same keyway (or key section) as permanent keying system. C. Permanent Keys and Cores: Prepare permanent cores and keys in accordance with keying schedule. [Stamp with applicable key mark for identification.] [Do not stamp.] [ ]. D. Provide Grand Masterkeys, Masterkeys and other Security Keys. E. Furnish keys in the following quantities: 1. [4] [ ] each Grand Masterkeys. 2. [4] [ ] each Masterkeys per set. 3. [2] [ ] each Change keys each keyed core. 4. [6] [ ] each Construction masterkeys. 5. [2] [ ] each Control keys. 6. Install permanent cores in locksets. F. Return construction cores to [{Stanley/BEST} factory representative] [Hardware manufacurer s representative]. CORMAX PATENTED KEYING SYSTEM CORMAX PATENTED KEYING SYSTEM One of the greatest threats to key control within your facility is the unauthorized duplication of keys; one simple solution is the use of the CORMAX Patented Keying System. Very seldom can a single product meet all of your exact needs, and often your level of convenience must be sacrificed to fit the capabilities of the product. The CORMAX Patented Keying System provides you with an significant amount of flexibility, enabling a solution that fits your unique balance between security and convenience. CORMAX Patented Keying System The CORMAX Patented Keying System is available in two series of keyways, the M Series and the X Series. Each series offers a different blend of features. For example the CORMAX Patented Keying System can provide geographic exclusivity to the customer to help you maximize convenience while optimizing your security. M Series Keyway Features Patented keys operate both CORMAX and Standard BEST cores (backward compatibility) with existing BEST keyway (J,K,L,M only). Standard keys do not operate CORMAX cores. Available in large bow, long blade, and long nose key blanks to work with special applications. Available core designs for use in special applications, such as high security mortise, hotel cylinders, and glass display-case locks. Utilizes the same combinating kits and key cutting equipment as the Standard BEST keyways. M Series keys operate CORMAX cores and Standard (non-patented) BEST cores. Standard key blanks do not operate CORMAX cores. X Series Keyway Features Distinctive key design includes thicker key blanks with larger bow for added strength and easier handling. Keyways are unique to CORMAX Patented Keying System offering even higher key duplication protection. CORMAX keyways utilize the standard combinating kit, minimizing the expense of system changeover. X Series keys operate CORMAX cores only. 10 HEAVY DUTY L

25 8KL3 Deadlocking Latch Bolt throw 9 /16" Backset 2 3 /4" Front 2 1 /4" x 1 1 /8" beveled. Tube To fit 1" diameter hole in door edge. To order: (wit h unit) designate 93K on How to Order (page 3). To order: (without unit) designate 8KL3-SL (Spring Latch) or DL (Deadlocking Latch) and finish. 8KL4 Deadlocking Latch Bolt throw 9 /16" Backset 3 3 /4" Front 2 1 /4" x 1 1 /8" beveled. Tube To fit 1" diameter hole in door edge. To order: (with unit) designate 94K on How to Order (page 3). To order: (without unit) designate 8KL4-SL" (Spring Latch) or DL (Deadlocking Latch) and finish. DEADLOCKING LATCHES 8KL5 Deadlocking Latch Bolt throw 9 /16" Backset 5" Front 2 1 /4" x 1 1 /8" beveled. Tube To fit 1" diameter hole in door edge. To order: (with unit) designate 95K on How to Order (page 3). To order: (without unit) designate 8KL5-SL (Spring Latch) or DL (Deadlocking Latch) and finish. DEADLOCKING LATCHES STRIKES STRIKES 8KS3-7/8 8KS3 7/8 Flat Strike Dimension: Conforms to ANSI A115.2 for 1 3 /4" doors (4 7 /8" x 1 7 /8" flat) To order: (with unit) designate S3-7/8 on How to Order (page 3). To order: (without unit) designate 8KS3-7/8 and fin ish. 8KS3 8KS3 Strike Dimension: Conforms to ANSI A115.2 for 1 3 /4" doors (4 7 /8" x 1 1 /8" with curved lip). To order: (with unit) designate S3 on How to Order (page 3). To order: (without unit) designate 8KS3 and fin ish. 8KS2 8KS2 Strike (Supplied Standard) Dimension: Conforms to ANSI A115.2 for 1 3 /8" doors (2 3 /4" x 1 1 /8" with curved lip and box). To order: (with unit) designate STK on How to Order (page 3). To order: (without unit) designate 8KS2 and finish. STRIKES & DOOR PREPARATION STRIKES & DOOR PREP. STK strike (standard) S3 strike 9K door preparation with through-bolt mountings OCK - LEVERS 11

26 FUNCTIONS FUNC TIONS Function & Diag. Description Outside Lever Inside Lever (ANSI No.) Latch operated by Locked by Unlocked by Locked by Unlocked by Single Keyed Entrance AB Cannot be locked Always unlocked F109 D Storeroom Rotating the inside lever, Rotating the outside lever only when the inside push button is out, Turning the key in the outside lever Turning the key in the outside lever, Rotating the inside lever Pushing the inside button, Pushing and turning the inside button. Turning the button keeps the outside lever locked until the button is turned back Always fixed Turning the key in the outside lever, (only when the button is not turned) Rotating the inside lever, (only when the button is not turned). Closing the door (only when the button is not turned) Cannot be unlocked Cannot be locked Always unlocked F86 Service Station E F92 Hotel Guest Rm. H F93 Hotel Guest Rm. HJ Indicator Included No Indicator Classroom R F84 Dormitory T F90 Double Keyed* Corridor C F88 Storeroom * G Rotating the inside lever, Rotating the outside lever-only when the inside push button is out. Turning the key in the outside lever Rotating the inside lever, Turning the key in the outside lever-only when the inside push button is out, Removing the core with a control key and using a special emergency key Pushing the inside button projects an occupied indicator in the outside lever and blocks all operating keys. Rotating the inside lever, Turning the key in the outside lever-only when the inside push button is out, Removing the core with a control key and using a special emergency key Pushing the inside button blocks all operating keys, but no occupied indicator is projected. Rotating the inside lever, Turning the key in the outside lever, Rotating the outside lever when not locked by key Rotating the inside lever, Rotating the outside lever when not locked by key or push button Rotating the inside lever, Rotating the outside lever when not locked by key, Turning the key in the outside lever Rotating the outside lever when not locked by key, Rotating the inside lever when not locked by key Pushing the inside button, Turning the key in the outside Pushing and turning the lever, inside button. Turning the Rotating the inside lever, button keeps the outside Closing the door-only when lever locked until the button is the button is not turned, Turning back the slotted turned back button Always fixed Always fixed Turning the key in the outside lever Turning the key in the outside lever, Pushing the button on the inside lever Turning the key in the inside lever Turning the key in the inside lever, Turning the key in the outside lever Key block feature is released by: Rotating the inside lever, Closing the door Key block feature is released by: Rotating the inside lever, Closing the door Turning the key in the outside lever Turning the key in the outside lever, Rotating the inside lever (only when locked by push button), Closing the door (only when locked by push button) Turning the key in the inside lever Turning the key in the inside lever, Turning the key in the outside lever Cannot be locked Cannot be locked Cannot be locked Cannot be locked Cannot be locked Cannot be locked Always unlocked Always unlocked Always unlocked Always unlocked Always unlocked Always unlocked Turning the key Turning the key in the inside lever, in the inside lever, Turning the key Turning the key in the outside in the outside lever lever F91 Turning the key in either the inside or the outside, locks or unlocks both sides. *ATTENTION: Locksets that secure both sides of the door are con trolled by building codes and the Life Safety Code. In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal. 6 HEAVY DUTY L

27 TRIM VARIATIONS TRIM VARIATIONS 14C 15C 16C 14D 15D 16D 14K 15K 16K 14L 15L 16L DIMENSIONS LEVER & TRIM DIMENSIONS 4 HEAVY DUTY L