EDUIMS INTERACTIVE MEDIA STATION. Assembly Instructions Qty 1 Bottom Frame Assembly Qty 1 Bottom Support Panel LH

Transcription

1 EDUIMS INTERACTIVE MEDIA STATION Qty 1 Bottom Frame Assembly Qty 1 Bottom Support Panel RH Qty 1 Bottom Support Panel LH Qty 1 Upper Frame Assembly Qty 1 Support Assembly Qty 2 Storage Bucket Qty 1 Cable Retention Bracket Qty 2 Monitor Support Tube Qty 2 Vertical Support Panel Qty 1 Main Support Qty 1 Laptop Tray E6 Unit - Qty Qty 2 Hook Bar Qty 1 770N Gas Spring Qty 1 Articulating Arm Qty 1 Handle Assembly

2 Qty 2 Stop Bracket Qty 4 M4 x mm Pan Hd Screw Qty 4 1 Square Black Foam Qty 2 1/4-20 x 1/2 Carriage Bolt Qty 4 M4 Nut Qty 2 Foam Pad Qty x 1 1/2 Button Sockets Screws Qty 2 1 Knurled Knob Qty 2 Outer Bracket Qty 2 Foam Pad Qty 4 4 Stem Caster w/brake Qty 10 1/4-20 x 1 1/4 Carriage Bolt Qty 16 1/4-20 Hex Nut Qty 2 1/4 Lockwasher Qty 2 Black Vinyl Cap Qty x 1.25 L Button Hd Screw Qty KEPS Nut W/ Tooth Qty 4 #6 x 1/2 Button Pin-In Hd Screws Qty 16 1/4-20 X 5/8 Combo Trus Screw Qty 4 #10-32 x 1/2 Truss Head Screw Qty 2 1/4-20 x 3/4 Phillips Screw Qty 16 Flat Washer Courtesy Monitor Hardware Pack Qty 1 2

3 1 TWO PERSON ASSEMBLY REQUIRED (4)x Lock Lock Lock 3

4 Faces shorter side Correct Position (4) 2x (4) 2x 4

5

6

7

8 (2)x (12)x

9 (16)x (8)x (8)x (2)x 9

10 (4)x 3 rd hole from bottom 1 st hole from bottom (4)x

11 8 Attach both hook bars onto the back of your monitor using the mounting holes built into the case. A courtesy hardware pack has been provided with several metric screw sizes. You may need to purchase additional metric screws from your local hardware store for a monitor with different mounting screw size. Screws provided in courtesy hardware pack # Top Bottom (2)x 11

12 9 TWO PERSON ASSEMBLY REQUIRED Hook monitor onto main support bar as shown. MONITOR NOT SHOWN FOR CLARITY 12

13 10 Attach the stop brackets to the hook bars as shown with security screws using the driver bit provided (2) 2x (1) 2x 13

14 11 Center your monitor horizontally and then tighten in place with screws (2)x 14

15 (4)x 15

16 13 E6 Unit 16

17 14 When attaching the cable to the cylinder, be very careful not to pull up on the lever. By doing this it may cause the cylinder to spring up Hook end of cable onto cylinder Slide in place 17

18

19 16 Slide cable through hole in handle assembly 19

20 17 Slide cable through eye lit hole and slide into slot Bottom View 20

21 18 With pliers, pull the cable through the next handle piece so that it sits in the narrow part of the eyelit hole. 21

22 19 Note: Can be mounted to either side of cart (2)x (2)x 22

23 (4)x (4)x 23

24 (2)x (2)x (1) 2x (1) 2x (1) 2x 24

25 23 NOTE: Before attaching the square foam pieces, decide where you are going to mount the outer brackets. Then proceed with attaching the foam squares (2)x (2)x (2)x (2)x 25

26 24 Bottom View Seymour Avenue Franklin Park, Illinois USA Toll Free Phone: Phone: Toll Free Fax: Fax: BRETFORD.COM Bretford, B design, and EDUIMS are trademarks or registered marks of Bretford Manufacturing, Inc. or Bretford Manufacturing, Ltd. Patents pending Bretford Manufacturing, Inc. All rights reserved. All other referenced product names and logos are trademarks of their respective owners.