Revised on : 07. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE15C AUTOMATIC MECHANICAL. SII Products
|
|
|
- Bennett James
- 5 years ago
- Views:
Transcription
1 Revised on : 07. Feb TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL SII Products
2 [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-02 NE15C Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy Duration time Winding the mainspring Jewels Crown position Outside diameter Casing diameter Total height Static accuracy Measurement position Lift angle Measurement time Posture difference Isochronisms (24h-0h) Normal position First click Second click Ф 27.40mm Ф 27.00mm 5.32mm 3 Hands ( Hour, Minute, Second ) Date Calendar Manual winding Automatic winding with ball bearing Stop second device Quick date correction 21,600 vibrations per hour -15~+25 seconds per day * Measurement should be done within 10~60 minutes after fully wound up. * All measurements are made without the calendar in function. Direction of 3 positions. (1) Dial up (2) 9 o'clock up (3) 6 o'clock up 53 deg. 20 seconds * Equipment to be used : Witschi WATCH EXPERT Difference is under 45 seconds within max value and minimum value. * Measurement should be done within 10~60 minutes after fully wound up. * Direction of 4 positions. (1) 12 o'clock up (2) 9 o'clock up (3) 6 o'clock up (4) 3 o'clock up -10~+20 seconds per day. * Direction of position. : Dial up * Difference of static accuracy of 24h and 0h More than 50 hours Mainspring after fully wound up. * Posture to confirmation : Dial up << Movements >> Fully wound up by turning the crown minimum 55 times. Fully wound up by turning the ratchet wheel screw 8 times. << Complete Watch >> A winding machine is needed to wind up the mainspring. Full wind up conditions Rotary speed : 30 rpm Operating time : 60 minute 24 jewels Counterclockwise Free Date setting Time setting Clockwise Manual winding Free Time setting SII Products 1
3 Disassembling procedures Figs Reassembling procedures Figs PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 NORMAL QUANTITY S-6 SUFFICIENT QUANTITY S-4 Version Date indicator maintaining plate screw Date indicator maintaining plate 3 Date dial Refer to the page 7 for the each parts code Date jumper SII Products 2
4 PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 S-6 NORMAL QUANTITY S-4 SUFFICIENT QUANTITY Version Date corrector setting transmission wheel E Hour wheel Minute wheel and pinion Guard for date corrector setting transmission wheel screw Intermediate date driving wheel and pinion Guard for date corrector setting transmission wheel Date indicator driving wheel Cannon pinion * Date corrector setting transmission wheel C Date corrector setting transmission wheel B Date corrector wheel *3 *2 * Lower shock absorbing spring 52-2 Lower shock absorbing cap jewel 52-3 Lower hole jewel frame for shock-absorber SII Products 3
5 PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 S-6 NORMAL QUANTITY S-4 SUFFICIENT QUANTITY Version Oscillating weight with ball bearing *2 * Automatic train bridge screw Balance bridge screw Automatic train bridge 23 whole tooth Second reduction wheel and pinion Balance cock Ratchet wheel screw Ratchet wheel Balance complete with stud Pallet bridge screw Pallet bridge * Pallet fork 23-2 Upper shock absorbing spring * Upper shock absorbing cap jewel 23-4 Upper hole jewel frame for shock-absorber SII Products 4
6 32 PARTS CATALOGUE Version-05 Type of oil Oil quantity mark Moebius 9010 S-6 NORMAL QUANTITY S-4 SUFFICIENT QUANTITY First reduction wheel Barrel and train wheel bridge screw Refer to page 8 for oiling spot 28-1 Cap jewelled spring 28-2 Cap jewell Pawl lever Rachet sliding wheel spring Refer to page 10 for the assembling method Barrel and train wheel bridge with hole jewel frame Refer to page 8 for oiling spot Reduction wheel holder Lower plate for barrel and train wheel bridge Fourth wheel and pinion Lower plate for barrel and train wheel bridge screw Third wheel and pinion Click Barrel complete with mainspring SII Products 5
7 PARTS CATALOGUE Type of oil Oil quantity mark Moebius 9010 S-6 NORMAL QUANTITY S-4 SUFFICIENT QUANTITY Version Center wheel bridge screw Center wheel bridge Escape wheel and pinion Center wheel and pinion with cannon pinion Yoke spring screw Yoke spring Yoke Balance stop lever Setting lever *2 *3 *4 Refer to page 9 for oiling spot *5 *4 *2 49 * Clutch wheel Winding pinion Date corrector setting transmission wheel A * Winding stem 52 Main plate SII Products 6
8 PARTS CATALOGUE Version-02 3 Date dial Parts code Position of crown Position of day frame Color of letters Color of background H 3H Black White List of screw No Parts code Parts name Parts form No Parts code Parts name Parts form 1 17 Date indicator maintaining plate screw (x4) Automatic train bridge screw (x2) Guard for date corrector setting transmission wheel screw (x2) Pallet bridge screw (x2) Lower plate for barrel and train wheel bridge screw Center wheel bridge screw Yoke spring screw (x2) Ratchet wheel screw Balance bridge screw Barrel and train wheel bridge screw (x3) SII Products 7
9 1.Oiling spot 28 Barrel and train wheel bridge with hole jewel frame TECHNICAL GUIDE Type of oil Oil quantity mark Moebius 9010 NORMAL QUANTITY S-6 SUFFICIENT QUANTITY S-4 Version-03 Barrel and train wheel bridge with hole jewel frame (back side) *3 *2 *3 *4 *2 Note *2 After oiling, set lower plate for barrel and train wheel bridge & screw. 34 Lower plate for barrel and train wheel bridge 33 Lower plate for barrel and train wheel bridge screw *4 After oiling, set first reduction wheel & pawl lever & reduction wheel holder. 32 First reduction wheel 32 First reduction wheel 31 Pawl lever 30 Reduction wheel holder SII Products 8
10 47 Balance stop lever Balance stop lever TECHNICAL GUIDE Version-02 Main plate Contact part of main plate and balance stop lever 2.Setting position of oscillating weight Before assembling oscillating weight. Match the center of the oscillating weight and winding stem. Set the hole of first reduction wheel gear on the imaginary line toward the balance bridge guide pin. Enlarged view Balance bridge guide pin First reduction wheel gear 3.To remove the winding stem 1) Set the winding stem to normal position. 2) Pull out the winding stem, while pushing "A" A 46 Setting lever 48 Winding stem SII Products 9
11 TECHNICAL GUIDE 4.Disassembling / assembling of the First reduction wheel << Disassembling >> << Assembling >> Version First reduction wheel 30 Reduction wheel holder 28 Barrel and train wheel bridge (back side) 5.Disassembling / assembling of the Ratchet sliding wheel spring. << Disassembling >> << Assembling >> 29 Ratchet sliding wheel spring 28 Barrel and train wheel bridge with hole jewel frame PUSH Remove the hook of the ratchet sliding wheel spring from barrel and train wheel bridge with hole jewel frame. The hooks of ratchet sliding wheel spring are hung up on barrel and train wheel bridge with hole jewel frame. SII Products 10
12 6.Accuracy adjustment TECHNICAL GUIDE Version-02 Regulator Stud support Regulator pin Note: Regulator Time adjustment Stud support Beat error adjustment (+) side (-) side Regulator pin Gap adjustment of balance spring and regulator pin Anticlockwise rotation No clockwise rotation SII Products 11
13 Version-02 TECHNICAL GUIDE 7.To wind up the mainspring <<Movement>> The mainspring would be fully wound up by turning the ratchet wheel screw 8 times clockwise. (Manual winding or Screwdriver) Manual winding Rotate crown clockwise at normal position by minimum 55 times. (Equal to ratchet wheel screw 8 times ) Screwdriver winding Turn the ratchet wheel screw 8 times clockwise. [ Manual winding ] [ Screwdriver winding ] Screwdriver Ratchet wheel screw Ratchet wheel 8.How to attach hands Place the movement directly on a flat metal plate or something similar to attach the hands. We recommend the use of movement holder to attach hands. Static weighting For hands attachment, please use a special equipment. When the movement receives a strong shock, it may be damaged. Metal plate 9.Accuracy measurement condition Static Accuracy : -15~+25 seconds per day Measurement Conditions 1) Measurement should be done within 10~60 minutes after fully wound up. 2) Lift angle : 53 deg 3) Measurement position : (1) Dial up (2) 9 o'clock up (3) 6 o'clock up 4) Minimum measurement Time : 20 seconds 5) Stabilizing Time : Leave the watch for at least 20 seconds to stabilize after you change its measurement position. SII Products 12
14 OPERATION Version-02 Minute hand Hour hand Second hand First click Second click Crown at normal position 1.Time setting 1) Pull out the crown to the second click position. 2) Turn the crown to set hour and minute hands. (Check that AM/PM is set correctly.) 3) Push the crown back into the normal position. 2.Date setting 1) Pull out the crown to the first click position. 2) Turn the crown to left for date setting. * Do not set the calendar between 10:00 P.M. and 1:00 A.M. If the setting of the calendar is made during this period, the date will not change to the next date. Please set the calendar after changing the time other than the above period. 3) Push the crown back into the normal position. 3.To wind up the mainspring a) Manual winding Rotate the crown clockwise at normal position. Wind turning the ratchet wheel screw 8 times. It will start to move naturally after shaking slightly. b) To wind up with winding machine. Full wind up conditions Rotary speed : 30 rpm Operating time : 60 minutes SII Products 13
Revised on : 23. May TECHNICAL GUIDE PARTS CATALOGUE. Cal.NH70/71 AUTOMATIC MECHANICAL. SII Products
Revised on : 23. May. 2018 TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL SII Products [SPECIFICATION] PARTS CATALOGUE / TECHNICAL GUIDE NH70 - NH71 Gilt version of NH70 Movement Movement size
TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE15 AUTOMATIC MECHANICAL. SII Products
TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-01 NE15 Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy
PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.
![PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.](/thumbs/89/100003756.jpg "PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.")
[SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE NE57A Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy Duration time Outside diameter Static accuracy Winding the
TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE20 AUTOMATIC MECHANICAL. SII Products
TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-01 NE20 Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy
PARTS LIST/ TECHNICAL GUIDE
/ TECHNICAL GUIDE Cal. 7S26C/7S36C [SPECIFICATIONS] Item Cal. No. 7S26C 7S36C 5 4 28 29 3 2 1 31 30 3 hands (hour, minute and second hands) Date indication Day indication Movement size Diameter Outside:
PARTS LIST / TECHNICAL GUIDE Automatic Cal.4R71A
[SPECIFICATION] Item PARTS LIST / TECHNICAL GUIDE Automatic Cal.4R71A Cal. No. 4R71A 3 Hands (Hour, Minute and Second hands) Movement Size Diameter Outside : φ27.4 mm Casing : φ27.0 mm Height : 5.32 mm
PARTS LIST / TECHNICAL GUIDE
[SPECIFICATIONS] PARTS LIST / TECHNICAL GUIDE Automatic Item Cal. No. 4R35B/4R36A The figures below are Cal. 4R36A. 3 hands (hour, minute and second hands) Day and Date indication Movement size Diameter
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Brand SEIKO Item Cal. No. 7S26B 7S36B Movement Movement size Outside diameter Casing diameter Height (x 1.5) Ø 27.4 mm Ø 27.0 mm 4.9 mm Time indication
Revised on : 9. Mar TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ22B Cal.VJ24B ANALOGUE QUARTZ. SII Products
Revised on : 9. Mar. 2016 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ22B Cal.VJ24B ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE VJ22B VJ24B [SPECIFICATION] Item Cal. No. VJ22B VJ24B Version-02 Movement
Cal.VJ5*B Series (VJ52/53/55)
Revised on : 05. Jun. 208 TECHNICAL GUIDE & PARTS CATALOGUE Series (VJ52/53/55) ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATION] Item Cal. No. Series Series VJ52B VJ53B VJ55B Version-02
Cal.VJ4*B Series (VJ42/43/45)
Revised on : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Series (VJ42/43/45) ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. Series Series VJ42B VJ43B VJ45B Version-02
Revised on. : 05. Jun TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ12B Cal.VJ14B ANALOGUE QUARTZ. SII Products
Revised on. : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ12B Cal.VJ14B ANALOGUE QUARTZ [SPECIFICATION] PARTS CATALOGUE / TECHNICAL GUIDE VJ12B VJ14B Cal. No. Item VJ12B VJ14B Version-02 Movement
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. V653B Movement size Outside diameter Casing diameter Height ø29.5 mm 26.0 mm between 3 o clock and 9 o clock sides ø28.8 mm 3.7
Revised on : 05. Jun TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ23B Cal.VJ33B ANALOGUE QUARTZ. SII Products
Revised on : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ23B Cal.VJ33B ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. VJ23B VJ33B VJ23B VJ33B Version-02 Movement
Revised on : 29. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK63/67/83 ANALOGUE QUARTZ. SII Products
Revised on : 29. Feb. 2016 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. Item VK63 VK67 VK83 Version04 Movement Movement size Time indication
Revised on : 29. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK61/64 ANALOGUE QUARTZ. SII Products
Revised on : 29. Feb. 2016 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] Item PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. VK61 VK64 Version03 Movement Movement size Time indication
Issued on: 11. May TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK61/64 ANALOGUE QUARTZ. SII Products
Issued on: 11. May. 2012 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] Item PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. VK61 VK64 Movement Movement size utside diameter Casing
BULOVA MODELS. Specifications. Designation of Types. 11 AOAC 11 AOACB Automatic 11 AOACD. Date. Movement DIAL SIDE TRAIN SIDE.
DIAL SIDE TRAIN SIDE BULOVA MODELS 11 AOAC 11 AOACB 11 AOACD Date Day + Date Scale 1:1 Specifications Movement 11y,'" Lever escapement 17 or 23 jewels Unbreakable and self-lubricated mainspring Total running
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 7N3C Cal. 7N33C Cal. 7N39C 7N3C 7N33C 7N39C Outside diameter The illustrations refer to Cal. 7N33C. ø4.0 mm 1.5 mm between
Specific information for calibre 3603
Fig. 1.0 1.0 Assembling of date indication 1. Stem in position 3 : Turn anti-clockwise the driving wheel for date unlocking yoke (reference 33029) until the finger of this wheel is aligned with the pin,
automatic, with center sweep-second automatic, calendar with center sweep-second automatic, day and date with center sweep-second
DIAL SIDE TRAIN SIDE Scale 1:1 Specifications Movement Automatic mechanism 11112 Ligne, lever escapement Diameter of the plate 25.60 mm Unbreakable and self-lubricated mainspring Total running time: 42
Calibre General information for Calibre Exploded views for calibre Specific information for calibre
Technical Guide TG-19-C-024-E C Produced by : pelrom Date: 20.09.2010 3 Modifications: see last page CALIBRE 3220 Version A 131/4 Ø 30 mm Height on movement Power reserve Number of jewels Frequency Lift
Revised on : 25 November 2014 TECHNICAL GUIDE PARTS CATALOGUE. Cal.VC00/01E ANALOGUE QUARTZ. SII Products
Revised on : 25 November 2014 TECHNICAL GUIDE & PARTS CATALOGUE ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE Cal.VC00 / 01E [SPECIFICATION] Item Cal. No. VC00E VC01E Version-01 Movement Movement size
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. 3M62A (x 1.0) Movement size Outside diameter Casing diameter Height ø24.0 mm ø23.3 mm 4.2 mm Time indication Driving system Additional
Revised on : 9. Mar TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ20C Cal.VJ21C ANALOGUE QUARTZ. SII Products
Revised on : 9. Mar. 2016 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ20C Cal.VJ21C ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. VJ20C VJ21C VJ20C VJ21C Version-02 Movement
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE PARTS CATALOGUE / TECHNICAL GUIDE (p. 1 21) CATÁLOGO DE PARTES / GUÍA TÉCNICA (p. 23 43) [SPECIFICATIONS] Item Movement Cal. No. 5J22A (x 1.0) Movement size Outside diameter
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE PARTS CATALOGUE / TECHNICAL GUIDE (p. 1 22) [SPECIFICATIONS] Item Movement Cal. No. 5J32A (x 1.0) Movement size Outside diameter Casing diameter ø26.4 mm ø25.6 mm Height
The chronograph calibres CHRO PC 17 jewels CHRO C12 PC 17 jewels CHRO C12 PC AMPM GMT 17 jewels CHRO PC CAL 17 jewels
Technical guide The chronograph calibres 860 27 CHRO PC 17 jewels 861 27 CHRO C12 PC 17 jewels 910 27 CHRO C12 PC AMPM GMT 17 jewels 930 27 CHRO PC CAL 17 jewels o 27.00 mm / Power-reserve Jewel number
Servicing a Poljot 3133 movement
Servicing a Poljot 3133 movement A service guide made by WUS member SLLS, June 2015 Editor: WUS member Polmax3133 Use this guide at your own risk. To dismantle a 3133 movement, just start at the end of
PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]
![PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]](/thumbs/86/93687150.jpg "PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]")
PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR [SPECIFICATIONS] Cal. No. Item V157A V157A/V158A Movement V158A Diameter Outside: 28.6 mm Casing: 24.0 mm Height: 3.5mm 3 hands (hour, minute and second hands)
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Cal. No. 6T63A 3 hands (hour, minute, and small second hand) 24-hour indicator Date indicator Diameter Outside: Ø 30.8 mm Height: 5.1 mm Casing:
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 5T82A 5T82A (x 1.0) Movement size Time indication Driving system Outside diameter Casing diameter Height (Movement intervals)
PARTS CATALOGUE / TECHNICAL GUIDE
PRTS CTLOGUE / TECHNICL GUIDE Cal. 7T62, 7T92 [SPECIFICTIONS] Item Cal. No. 7T62 7T92 Movement The illustrations refer to Cal. 7T62. (x 1.0) Movement size Outside diameter Casing diameter ø27.6 mm ø27.0
Special Points. Specifications TRAIN SIDE DIAL SIDE. Scale 2V2:1
DAL SDE TRAN SDE Scale 2V2:1 Specifications 7% ligne, lever escapement Diameter of plate 17.20 mm. Total running time: 47 hours Screwless beryllium 21,600 beats per hour Adjustable stud holder balance
PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]
![PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]](/thumbs/87/95546534.jpg "PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]")
PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR [SPECIFICATIONS] Item Cal. No. V175A 3 hands (hour, minute and small second hands), 24-hour indicator Diameter: Height: Outside 27.6 mm.casing 27.0 mm 4.4 mm
PARTS LIST / TECHNICAL GUIDE Perpetual Calendar/Alarm Chronograph Cal. 7T86A
PARTS LIST / TECHNICAL GUIDE Perpetual Calendar/Alarm Chronograph [SPECIFICATIONS] Item Cal. No. Movement 7T86A 7T86A 3 hands (hour, minute, and small second hands) Interval of hands movements Driving
PARTS LIST / TECHNICAL GUIDE
PARTS LIST / ANALOGUE SOLAR [SPECIFICATIONS] Item Cal. No. V172A/V174A V172A V174A 3 hands (hour, minute and small second hands) 3 hands (hour, minute and small second hands), 24-hour indicator Diameter:
PARTS CATALOGUE / TECHNICAL GUIDE
PRTS CTLOGUE / TECHNICL GUIDE [SPECIFICTIONS] Cal. 7T62/7T92/7T94 Item Cal. No. 7T62 7T92 7T94 Movement The illustrations refer to Cal. 7T62. (x 1.0) Movement size Outside diameter Casing diameter Ø 27.6
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 7T84A 7T84A (x 1.0) Movement size Time indication Driving system Outside diameter Casing diameter Height Additional mechanism
Cal.5D22A TECHNICAL GUIDE
No. PROCESS ILLUSTRATIONS AND SPECIAL INSTRUCTIONS ETC. Mount the secondary battery unit. Mount the insulator for secondary battery. Mount the secondary battery guard. Fix the insulator for secondary battery
PARTS CATALOGUE/TECHNICAL GUIDE Cal. 7D46A, 7D48A
PARTS CATALOGUE/TECHNICAL GUIDE Cal. 7D46A, 7D48A SPECIFICATIONS Item Cal. No. 7D46A, 7D48A Movement Movement Outside diameter size Casing diameter Height Time indication (Movement intervals) Driving system
7D** Technical Instruction No.1
Assembling the switching unit Set the main plate. 91 Set the main plate. 90 89 88 87 86 85 84 Set the lead pin for RZ1. Set the hour and minute stator. Set the second stator. Set the generating stator.
Cal. VR33A CHRONOGRAPH 13 1/ mm. 3 years. Ø 30.6mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing CHRONOGRAPH Cal. VR33A Movement Size 13 1/2 Casing Diameter Ø 30.6mm Height 3.97mm Battery Life 3 years Cal. VR33A Date: 31/Aug./'18 Items Rev. Page Specifications
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Cal. H021B Cal. H022A Cal. H023A Item Movement Cal. No. H021B, H022A, H023A Movement size Time indication Driving system Display system Outside diameter
Caution for disassembling The hour wheel is made of engineering plastics. When pulling out the hour hand, take care not to damage the hour wheel.
III. REMRKS ON DISSSEMLING ND RESSEMLING Hands Dial Caution for disassembling The hour wheel is made of engineering plastics. When pulling out the hour hand, take care not to damage the hour wheel. How
Cal. VS22A SOLAR SERIES 7 3/ mm. Approx. 6 months. Ø 18.1mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS22A Movement Size 7 3/4 Casing Diameter Ø 18.1mm Height 2.76mm Running Time Approx. 6 months Cal. VS22A Date: 29/Jun./'18 Items Rev. Page Features
Cal. AS32A SOLAR SERIES 10 1/ mm. Approx. 4 months. Ø 23.3mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. AS32A Movement Size 10 1/2 Casing Diameter Ø 23.3mm Height 4.61mm Running Time Approx. 4 months Date: 31/Oct./'16 Cal. AS32A Items Rev. Page Features
Cal. YM92A. φ27.0 mm H 3.7 mm. S.EPSON Products
Cal. YM92A φ27.0 mm H 3.7 mm Items Rev. Page Specifications 03 1 Appearance 00 2 Casing 03 3 Hand fitting 01 4 Hand setting stem 01 5 Dial-01 01 6-01 Dial-02 00 6-02 Dial-03 00 6-03 Dial-04 00 6-04 Casing
Cal. VR43A SOLAR SERIES 13 1/ mm. Approx. 4 months. Ø 30.6mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VR43A Movement Size 13 1/2 Casing Diameter Ø 30.6mm Height 4.52mm Running Time Approx. 4 months Date: 30/Nov./'17 Cal. VR43A Items Rev. Page Features
Cal. VS3JA SOLAR SERIES 10 1/ mm. Approx. 6 months. Ø 24.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS3JA Movement Size 10 1/2 Casing Diameter Ø 24.0mm Height 3.47mm Running Time Approx. 6 months Date: 2/May/'17 Cal. VS3JA Items Rev. Page Features
PARTS LIST / TECHNICAL GUIDE
PARTS LIST / TECHNICAL GUIDE Analogue Solar [SPECIFICATIONS] Item Cal. No. V114A 2 hands (hour, minute hands) Diameter Outside: Ø 15.5 mm x 11.8 mm Casing: Ø 15.15 mm x 11.80 mm Height: Ø 2.0 mm Interval
Cal. VS75A SOLAR SERIES. 4.40mm. Approx. 6 months. Ø 27.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS75A Movement Size 12 Casing Diameter Ø 27.0mm Height 4.40mm Running Time Approx. 6 months Cal. VS75A Date: 1/Sep./'15 Items Rev. Page Features
Cal. VS37A SOLAR SERIES 10 1/ mm. Approx. 6 months. Ø 24.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS37A Movement Size 10 1/2 Casing Diameter Ø 24.0mm Height 2.98mm Running Time Approx. 6 months Date: 15/Dec./'17 Cal. VS37A Items Rev. Page Features
Table of ConTenTs. Analog Chronographs 1/1 of a Second - Type C with small chronograph seconds and 24-hour hands 15
Table of ConTenTs 2- and 3-Hand Models 1 Date/Big Date Display Models - Type A 2 Date/Big Date Display Models - Type B 3 Automatic Models 4 Multi-Eye Models 5 Multi-Eye Models with Retrograde Day/Date
2. Uncasing. 5. Remove the clamp screws (casing ring / middle and movement / casing ring) and the clamps. 6. Remove the casing ring.
Calibre 360 1. Presentation 2. Uncasing 3. Chronograph movement (module) / M2 replacement procedure 4. Overhauling the base movement 5. Assembling the base movement with the chronograph movement 6. Chronograph
CALIBRE Q SCS CAL CORH CORM CORS 7 jewels Description et performances
Technical guide CALIBRE 1370 25.60 Q SCS CAL CORH CORM CORS 7 jewels Description et performances The caliber 1370, destined for a man's electronic watch with analogical display, is fitted with a quartz
Cal. VS17A SOLAR SERIES 5 1/ mm. 2.79mm. Approx. 6 months. Watch Movement Specification and Drawing. Movement Size.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS17A Movement Size 5 1/2 Casing Diameter 11.8 15.15 mm Height 2.79mm Running Time Approx. 6 months Date: 31/Aug/'17 Cal. VS17A Items Rev. Page
DIRECT DRIVE: THE REMARKABLE BULOVA ACCUTRON CALIBER 214
Lehekülg 1/5 13.05.2013 1:04 Search DIRECT DRIVE: THE REMARKABLE BULOVA ACCUTRON CALIBER 214 By Walt Odets Site Map TimeZone Italia Login / Register Register for TimeZone! Registering provides access to
Synchronous Wired and Electronic Movement Manual
Synchronous Wired and Electronic Movement Manual Hanson Movement General Synchronous-wired and electronic secondaries are controlled by a Hansen movement. Except for a short correction cycle each hour,
Pneumatic-Pneumatic Positioner YT-1200L,R Installation manual
Installation Safety Warning When installing a positioned, please ensure to read and follow safety instruction. All input and supply pressure to valve, actuator, and other related devices must be turned
Smart Positioner YT-2400L,R Installation manual
Installation Safety Warning When installing a positioner, please ensure to read and follow safety instruction. All input and supply pressure to valve, actuator, and other related devices must be turned
./#0#. 1"&." 1994 ELECTRICAL Suzuki of America Corp. - Starters. Swift
!"" #$%!& '()!)((*(+,*)- 1994 ELECTRICAL Suzuki of America Corp. - Starters Swift Two types of starter motors are used, conventional and reduction gear. Both types of starters consist of yoke assembly,
TECHNICAL INFORMATION INFORMACION TECNICA
TECHNICL INFORMTION INFORMCION TECNIC CITIZEN QURTZ Cal. No. E76 (Cal. No. E760) ENGLISH Contents 1. FETURES...1 2. BEFORE USING...1 3. SPECIFICTIONS...2 4. SETTING THE TIME ND DTE...3 5. FUNCTIONS UNIQUE
OVERHAUL. 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit.
STARTING & CHARGING 195 OVERHAUL 190C702 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit. A57559 (b) (c) (d) Remove the 2 screws
This Master Clock is designed for use on small low voltage electric time systems (those operating on up to 10 volts).
[The following is a partial reproduction of an undated brochure entitled Instructions For Care And Installation, Style A Master Clock Made By International Time Recording Co. of New York with general offices
WESCO INDUSTRIAL PRODUCTS, INC. Manual Non Telescoping High Lift Truck. Part Number: &
WESCO INDUSTRIAL PRODUCTS, INC Manual Non Telescoping High Lift Truck Part Number: 272462 & 272463 Note: Operator MUST read and understand these operating instructions before using this Truck. TABLE OF
DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
FOR THL MAN BEHIND THE BENCH
FOR THL MAN BEHIND THE BENCH se code s/ Jlaru nzarer1a1 {. for qu ck aid 0 11red BOY PRQOF -wa-fches Reduced view of Boyproof Watch 16 Size, Stem Wind and Set COPYRIGHT 1909 BY THE WESTJ:RN CLOCK MFG.
STRENGTH Enclosed head design seals out contaminants for improved performance and life.
T H E P E R F O R M A Enclosed head design seals out contaminants for improved performance and life. Torque wrap design reduces stress on gear and pawl teeth. Innovative linear ball bearing system eliminates
STEERING COLUMN - TILT
STEERING COLUMN - TILT 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate a mainshaft, attached by a "U" joint to an
TECHNICAL SPECIFICATIONS OF THE SPLIT SECONDS CHRONOGRAPH RICHARD MILLE RM 004-V2 FELIPE MASSA
TECHNICAL SPECIFICATIONS OF THE SPLIT SECONDS CHRONOGRAPH RICHARD MILLE RM 004-V2 FELIPE MASSA Following the success of the RM 005 in 2006 and the RM 011 in 2007, the RM 004 is the latest model to carry
1GR-FE STARTING STARTER (for 4WD) DISASSEMBLY
14 1GR-FE ARTING ARTER (for 4WD) DISASSEMBLY 1. REMOVE ARTER YOKE ASSEMBLY (a) Remove the nut, then disconnect the lead wire from terminal C. Remove the 2 through bolts. (c) Pull the starter yoke and the
CITYSTORM USER GUIDE
CITYSTORM USER GUIDE Congratulations on your purchase of a GIANT Citystorm. GIANT Citystorm represents the latest in design and engineering, and also requires special care. While Giant icycle engineers
TABLE OF CONTENTS. Cordless Impact Driver. Model No. EY7542. Europe Oceania
Order Number PTD0707X38CE Cordless Impact Driver Model No. EY7542 Europe Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications -----------------------------------------------------
Transmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
Grande Précision TimeMover Collector 48 the time machine
TimeMover Mechanical watches are more than just timekeepers. The lovely ticking of perfectly machined parts combine to produce masterpieces of horology many of which now have achieved collector status.
2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul
2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle
Short Shifter Installation Instructions Miata 6-Speed manual
Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter
Dec. 2, G. DUsos ETAL 3,543,506 SELF-WINDING, WRISTWATCH WITH A CHRONOGRAPH MECHANISM INVENTORS GERALD DVBOIS PAUL MARMER.
Dec. 2, 1970 G. DUsos ETAL 3,543,506 SELF-WINDING, WRISTWATCH WITH A CHRONOGRAPH MECHANISM Filed Aug. 1, 1968 5 Sheets-Sheet INVENTORS GERALD DVBOIS PAUL MARMER 22e 24 ATTORNEYS Dec. 1, 1970 SEIF-WINDING
1 HR-301/D Parts Manual. Table Of Contents
Table Of Contents 301/D Parts Manual 3 Point Hitch...2 Pull-Type Hitch...4 Main Frame...6 Angle Adjuster - Serial Number 44982 & Prior...8 Rotor Assembly - Serial Number 44982 & Prior...10 Rotor Assembly
Shimano Trinidad\Torium Drag Upgrade Tutorial
Shimano Trinidad\Torium Drag Upgrade Tutorial Introduction: This tutorial is provided to assist those of you who may be interested in performing upgrade of the drag system of your Shimano Trinidad 16,
Repair Manual VW 02J gearbox. INA GearBOX
Repair Manual VW 02J gearbox INA GearBOX Special tools Pipe section, 50 mm: Press fitting of synchronizer body for third/fourth gear. Assembly of support bearing for input and output shaft. Part number:
Hopkinsons Fig 9052 VALVE ACTUATOR
Excellent Power & Industrial Solutions Standard Operating & Maintenance Instructions Hopkinsons Fig 9052 VALVE ACTUATOR CUT-AWAY OF FIG. 9052 GEAR BOX, WITH LIMIT SWITCH & VALVE POSITION INDICATOR HOP
Disassembly and Reassembly Manual
AS No.ER2-0908-MC-00 ER2 Series Electric Chain Hoist (125kg to 5t) Disassembly and Reassembly Manual Safety precaution This Disassembly and Reassembly Manual includes contents to prevent injury to any
1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
Clock and watch escapements, power stamps and hammers, power punch, rotary conveyer, blower, pile driver and miscellaneous devices.
K»\ IX Nos. 1-21) 144 Clock and watch escapements, power stamps and hammers, power punch, rotary conveyer, blower, pile driver and miscellaneous devices. MECHANICAL MODELS 57 Section IX 129. Clock escapement.
Z TECHNICAL INSTRUCTIONS
ÍNDICE: Z40 2.0 TECHNICAL INSTRUCTIONS 1.- Error list 2.- Replace the control board 3.- Opening the machine 4.- Replace the power board 5.- Dismantling motor and gear box 6.- Assembly of gear box 7.- Pushing
Telephone:(925) Fax:(925) Lawrence Drive, Livermore, CA
Telephone:(95)5-9500 Fax:(95)5-950 5 Lawrence Drive, Livermore, CA 955 www.fabcoautomotive.com Table of Contents This manual covers single and dual rear output versions of the TC- two-speed transfer case
Updated gear lash procedures for the compact gear train assembly have been added to the Series 60 Service Manual.
NUMBER: 14 60 03 S.M. REF.: 1.21 ENGINE: 60 DATE: November 2003 SUBJECT: GEAR TRAIN AND CAMSHAFT GEAR LASH PROCEDURES FOR THE COMPACT GEAR TRAIN ASSEMBLY INTRODUCTION Updated gear lash procedures for the
RONDA normtech 700 & Caliber 6004.B 11½''' Long battery-life and special functionality. Features. Product Specifications. Analog quartz movement
RONDA normtech 700 & 6000 Long battery-life and special functionality Caliber 6004.B 11½''' Product Specifications Features Analog quartz movement Repairable metal watch movement Line normtech Caliber
An idea endures three centuries for a reason. Still, that doesn t mean you can t improve it. Mirrored Force Resonance
THE WORLD S FIRST An idea endures three centuries for a reason. Still, that doesn t mean you can t improve it. Mirrored Force Resonance Resonance is a sophisticated and demanding horological technique.
2002 Escape Workshop Manual
SECTION 303-01B: Engine 3.0L (4V) IN-VEHICLE REPAIR Procedure revision date: 10/09/2003 Timing Drive Components Removal CAUTION: Failure to verify correct timing drive component alignment will result in
CHAPTER 22 STARTER Models J05C-TD, J08C-TP and TR
1 INDEX STARTER 22-1 22-114E-03 CHAPTER 22 STARTER TROUBLESHOOTING...22-2 STARTER...22-4 22 22-2 STARTER 1 page 1 TROUBLESHOOTING Symptom Possible cause Remedy Engine does not crank, or cranks slowly Key
SECTION 9 CRANKING SYSTEM CONTENTS
SECTION 9 CRANKING SYSTEM CONTENTS 9-1. 9-2. 9-3. 9-4. 9-5. 9-6. 9-7. 9-8. GENERAL DESCRIPTION.,...,..., 9-2 SPECIFICATIONS.......................................... 9-4 LUBRICATION 9-5 REMOVAL AND INSTALLATION...
HKS 700E. Service Manual June Ver. 2.04
HKS 700E Service Manual 009 June Ver..04 HKS CO.,LTD 78 KITAYAMA FUJINOMIYA SHIZUOKA JAPAN 48-09 TEL +8(0)544-54-78 FAX +8(0)544-54-40 hks_aviation@hks-power.co.jp http://www.hks-power.co.jp/hks_aviation/
1991 Mazda MX-5 Miata. STARTER - DIRECT DRIVE ELECTRICAL Mazda Starters - Direct Drive ELECTRICAL Mazda Starters - Direct Drive
DESCRIPTION STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive Nippondenso direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is attached
CALIBRE 1387 R 13 Q CORH CORM
Description CALIBRE 1387 R 13 Q CORH CORM 3 jewels (13 x 15.15 x 2.3) 13.00 x 15.15 mm Movement height 2.30 mm Jewel number Frequency 3 32'768 A/h GENERAL DESCRIPTION A new design in quartz watches with
Crestline Dampening System. Installation Instructions. Ryobi 500N X /98
Crestline Dampening System Installation Instructions Ryobi 500N X88-33 7/98 GENERAL INFORMATION ATTENTION CRESTLINE DAMPENER OWNER! Accel Graphic Systems provides parts and service through its authorized
Конференция "Обменяемся опытом. Нива" NIVA-FAQ. undefined
NIVA-FAQ Gearbox removal By Volodjushka NOVELTIES FAQ THE SITEMAP SEARCH ON THE SITE Конференция "Обменяемся опытом. Нива" NIVA-FAQ undefined Works in the motor compartment Remove the battery negative
G85CS Parts list. Frank Kyul, Netherlands
G85CS Parts list Frank Kyul, Netherlands http://home.wanadoo.nl/fxkuyl/ CYLINDER BARREL & HEAD 022298 Barrel Cylinder 1 022515 Washer Cylinder Base 1 015351 Nut. Sleeve Cylinder Head 4 042157 Washer Sleeve