Revised on : 9. Mar TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ20C Cal.VJ21C ANALOGUE QUARTZ. SII Products
|
|
|
- Thomasine Stanley
- 6 years ago
- Views:
Transcription
1 Revised on : 9. Mar TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ20C Cal.VJ21C ANALOGUE QUARTZ
2 [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. VJ20C VJ21C VJ20C VJ21C Version-02 Movement Movement size Outside diameter Casing diameter φ18.50 mm mm : between 12 o'clock and 6 o'clock sides mm : between 3 o'clock and 9 o'clock sides φ18.10 mm mm : between 12 o'clock and 6 o'clock sides Total height 2.28 mm ( including the battery ) Time indication 2 Hands 3 Hands Driving System Step motor (Load compensated driving pulse system type) Additional mechanism Electronic circuit reset switch Electronic circuit reset switch Second setting device Loss/Gain (Monthly rate) Frequency of crystal oscillator Operational temperature range Regulation system Measuring gate by quartz tester Battery Jewels Less than ±20seconds at normal temperature range 32,768 Hz - 5 ~ + 50 Nil Use 10-second gate * Set the winding stem with crown at the normal position SR621SW (Silver oxide battery) Battery life is approximately 3 years 0 Jewel 1
3 Disassembling procedures Figs. Reassembling procedures Figs *Refer to the 4pages for the each parts code PARTS CATALOGUE Version-03 Lubricating : Types of oil Oil quantity Moebius 9010 NORMAL QUANTITY Moebius 9030 << VJ20C >> << VJ21C >> 1 Hour and minute hands 1 Hour, minute and second hands 2 Dial 2 Dial 2
4 PARTS CATALOGUE Version-05 3 Battery Winding stem Battery Circuit block with coil block connection (+) screw 6 * Battery connection (+) * * Fourth wheel and pinion Fifth wheel and pinion Third wheel and pinion Insulator Step rotor Reset pin Rotor stator Battery connection (-) Train wheel setting lever Setting wheel * Train wheel bridge Center wheel and pinion *1 Oiling position * Clutch wheel *2 Oiling position < VJ20C / VJ21C > *Refer to the 4pages for the each parts code 3
5 PARTS CATALOGUE Version-02 O The part which is not common in Parts name VJ20C VJ21C 6 Battery connection(+) Train wheel bridge Fourth wheel and pinion * All parts code are subject to change without notice. 4
6 TECHNICAL GUIDE Version-03 The explanation here is only for the particular points of Cal.VJ20/21 Ⅰ. STRUCTURE OF THE CIRCUIT BLOCK Notes: Since the circuit block and coil block are made by one piece, in disassembling and reassembling take care not to cut the coil line. Crystal unit C-MOS-IC Input terminal(+) Coil block Input terminal(-) Ⅱ. REMARKS ON DISASSEMBLING AND REASSEMBLING 1 Hands How to install Place the movement directly on a flat metal plate or the like to install the hands. Metal plate 2 Battery How to install battery Insert the battery aslant in the direction shown by the arrow. Check the battery connection (+) securely touches the side face of the battery. Coil block Correct 3 Battery connection (+) Battery Main plate Battery connection (+) How to install Have the hook portions (3 places) catch the main plate (Fig.1&2). In disassembling and reassembling, take care not to deform the hook portions. After installing the battery connection (+), check that the three hook portions securely catch the main plate. [ Fig. 1] [ Fig. 2] Hook portion Tweezers Hook portion Hook portion Main plate 5
7 TECHNICAL GUIDE Version-02 4 Insulator Setting position Notes: In order to insulate the battery connection (+) and the battery connection (-), the insulator should put at the three pin securely as below. Pin Insulator 5 Train wheel bridge Setting position Notes: Since the fifth wheel and pinion and step rotor are made of plastics, take care not to damage them in disassembling and reassembling. Third wheel and pinion Setting wheel Step rotor Fourth wheel and pinion Fifth wheel and pinion Setting wheel Step rotor Clutch wheel Fifth wheel and pinion Clutch wheel Third wheel and pinion Reset pin Fourth wheel and pinion 6 Center wheel and pinion Train wheel setting lever Setting position Notes: Catch the part of spring of the train wheel setting lever to the pin like as below. Take care not to deform the spring portion of the train wheel setting lever. Train wheel setting lever 6
8 TECHNICAL GUIDE Version-03 7 Notes: In disassembling and reassembling,take care not to damage the portion that is assembled of the pin. ( Since the portion that is assembled of the pin is made of plastics and easily damaged.) In disassembling, pick the pin up main plate to vertical direction with care. Tweezers Center wheel and pinion In reassembling, push the pin in main plate to vertical direction with care. Setting wheel Main plate (The portion that is assembled of the pin) Center wheel and pinion 7
Revised on. : 05. Jun TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ12B Cal.VJ14B ANALOGUE QUARTZ. SII Products
Revised on. : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ12B Cal.VJ14B ANALOGUE QUARTZ [SPECIFICATION] PARTS CATALOGUE / TECHNICAL GUIDE VJ12B VJ14B Cal. No. Item VJ12B VJ14B Version-02 Movement
Revised on : 9. Mar TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ22B Cal.VJ24B ANALOGUE QUARTZ. SII Products
Revised on : 9. Mar. 2016 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ22B Cal.VJ24B ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE VJ22B VJ24B [SPECIFICATION] Item Cal. No. VJ22B VJ24B Version-02 Movement
Revised on : 05. Jun TECHNICAL GUIDE PARTS CATALOGUE. Cal.VJ23B Cal.VJ33B ANALOGUE QUARTZ. SII Products
Revised on : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Cal.VJ23B Cal.VJ33B ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. VJ23B VJ33B VJ23B VJ33B Version-02 Movement
Revised on : 25 November 2014 TECHNICAL GUIDE PARTS CATALOGUE. Cal.VC00/01E ANALOGUE QUARTZ. SII Products
Revised on : 25 November 2014 TECHNICAL GUIDE & PARTS CATALOGUE ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE Cal.VC00 / 01E [SPECIFICATION] Item Cal. No. VC00E VC01E Version-01 Movement Movement size
Cal.VJ5*B Series (VJ52/53/55)
Revised on : 05. Jun. 208 TECHNICAL GUIDE & PARTS CATALOGUE Series (VJ52/53/55) ANALOGUE QUARTZ PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATION] Item Cal. No. Series Series VJ52B VJ53B VJ55B Version-02
Cal.VJ4*B Series (VJ42/43/45)
Revised on : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE Series (VJ42/43/45) ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. Series Series VJ42B VJ43B VJ45B Version-02
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 7N3C Cal. 7N33C Cal. 7N39C 7N3C 7N33C 7N39C Outside diameter The illustrations refer to Cal. 7N33C. ø4.0 mm 1.5 mm between
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. V653B Movement size Outside diameter Casing diameter Height ø29.5 mm 26.0 mm between 3 o clock and 9 o clock sides ø28.8 mm 3.7
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. 3M62A (x 1.0) Movement size Outside diameter Casing diameter Height ø24.0 mm ø23.3 mm 4.2 mm Time indication Driving system Additional
Revised on : 29. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK63/67/83 ANALOGUE QUARTZ. SII Products
Revised on : 29. Feb. 2016 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. Item VK63 VK67 VK83 Version04 Movement Movement size Time indication
Revised on : 29. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK61/64 ANALOGUE QUARTZ. SII Products
Revised on : 29. Feb. 2016 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] Item PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. VK61 VK64 Version03 Movement Movement size Time indication
Issued on: 11. May TECHNICAL GUIDE PARTS CATALOGUE. Cal.VK61/64 ANALOGUE QUARTZ. SII Products
Issued on: 11. May. 2012 TECHNICAL GUIDE & PARTS CATALGUE Cal. ANALGUE QUARTZ [SPECIFICATIN] Item PARTS CATALGUE / TECHNICAL GUIDE Cal. Cal. No. VK61 VK64 Movement Movement size utside diameter Casing
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Cal. No. 6T63A 3 hands (hour, minute, and small second hand) 24-hour indicator Date indicator Diameter Outside: Ø 30.8 mm Height: 5.1 mm Casing:
PARTS CATALOGUE / TECHNICAL GUIDE
PRTS CTLOGUE / TECHNICL GUIDE Cal. 7T62, 7T92 [SPECIFICTIONS] Item Cal. No. 7T62 7T92 Movement The illustrations refer to Cal. 7T62. (x 1.0) Movement size Outside diameter Casing diameter ø27.6 mm ø27.0
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE PARTS CATALOGUE / TECHNICAL GUIDE (p. 1 21) CATÁLOGO DE PARTES / GUÍA TÉCNICA (p. 23 43) [SPECIFICATIONS] Item Movement Cal. No. 5J22A (x 1.0) Movement size Outside diameter
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE PARTS CATALOGUE / TECHNICAL GUIDE (p. 1 22) [SPECIFICATIONS] Item Movement Cal. No. 5J32A (x 1.0) Movement size Outside diameter Casing diameter ø26.4 mm ø25.6 mm Height
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Cal. H021B Cal. H022A Cal. H023A Item Movement Cal. No. H021B, H022A, H023A Movement size Time indication Driving system Display system Outside diameter
PARTS CATALOGUE / TECHNICAL GUIDE
PRTS CTLOGUE / TECHNICL GUIDE [SPECIFICTIONS] Cal. 7T62/7T92/7T94 Item Cal. No. 7T62 7T92 7T94 Movement The illustrations refer to Cal. 7T62. (x 1.0) Movement size Outside diameter Casing diameter Ø 27.6
PARTS LIST / TECHNICAL GUIDE
PARTS LIST / TECHNICAL GUIDE Analogue Solar [SPECIFICATIONS] Item Cal. No. V114A 2 hands (hour, minute hands) Diameter Outside: Ø 15.5 mm x 11.8 mm Casing: Ø 15.15 mm x 11.80 mm Height: Ø 2.0 mm Interval
PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]
![PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]](/thumbs/86/93687150.jpg "PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR Cal. V157A/V158A [SPECIFICATIONS]")
PARTS LIST /TECHNICAL GUIDE ANALOGUE SOLAR [SPECIFICATIONS] Cal. No. Item V157A V157A/V158A Movement V158A Diameter Outside: 28.6 mm Casing: 24.0 mm Height: 3.5mm 3 hands (hour, minute and second hands)
PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]
![PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]](/thumbs/87/95546534.jpg "PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR Cal. V175A [SPECIFICATIONS]")
PARTS LIST / TECHNICAL GUIDE ANALOGUE SOLAR [SPECIFICATIONS] Item Cal. No. V175A 3 hands (hour, minute and small second hands), 24-hour indicator Diameter: Height: Outside 27.6 mm.casing 27.0 mm 4.4 mm
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 5T82A 5T82A (x 1.0) Movement size Time indication Driving system Outside diameter Casing diameter Height (Movement intervals)
PARTS LIST / TECHNICAL GUIDE
PARTS LIST / ANALOGUE SOLAR [SPECIFICATIONS] Item Cal. No. V172A/V174A V172A V174A 3 hands (hour, minute and small second hands) 3 hands (hour, minute and small second hands), 24-hour indicator Diameter:
PARTS LIST / TECHNICAL GUIDE Perpetual Calendar/Alarm Chronograph Cal. 7T86A
PARTS LIST / TECHNICAL GUIDE Perpetual Calendar/Alarm Chronograph [SPECIFICATIONS] Item Cal. No. Movement 7T86A 7T86A 3 hands (hour, minute, and small second hands) Interval of hands movements Driving
Revised on : 23. May TECHNICAL GUIDE PARTS CATALOGUE. Cal.NH70/71 AUTOMATIC MECHANICAL. SII Products
Revised on : 23. May. 2018 TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL SII Products [SPECIFICATION] PARTS CATALOGUE / TECHNICAL GUIDE NH70 - NH71 Gilt version of NH70 Movement Movement size
TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE15 AUTOMATIC MECHANICAL. SII Products
TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-01 NE15 Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy
TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE20 AUTOMATIC MECHANICAL. SII Products
TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-01 NE20 Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy
PARTS CATALOGUE/TECHNICAL GUIDE Cal. 7D46A, 7D48A
PARTS CATALOGUE/TECHNICAL GUIDE Cal. 7D46A, 7D48A SPECIFICATIONS Item Cal. No. 7D46A, 7D48A Movement Movement Outside diameter size Casing diameter Height Time indication (Movement intervals) Driving system
Revised on : 07. Feb TECHNICAL GUIDE PARTS CATALOGUE. Cal.NE15C AUTOMATIC MECHANICAL. SII Products
Revised on : 07. Feb. 2018 TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL SII Products [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Version-02 NE15C Cal. No. Movement Movement size Time
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Movement Cal. No. Cal. 7T84A 7T84A (x 1.0) Movement size Time indication Driving system Outside diameter Casing diameter Height Additional mechanism
PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.
![PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.](/thumbs/89/100003756.jpg "PARTS CATALOGUE / TECHNICAL GUIDE Cal.NE57A Version-01 NE57A [SPECIFICATION] Cal. No. Item. Movement. Outside diameter. Movement size.")
[SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE NE57A Cal. No. Movement Movement size Time indication Basic function Frequency Accuracy Duration time Outside diameter Static accuracy Winding the
PARTS LIST/ TECHNICAL GUIDE
/ TECHNICAL GUIDE Cal. 7S26C/7S36C [SPECIFICATIONS] Item Cal. No. 7S26C 7S36C 5 4 28 29 3 2 1 31 30 3 hands (hour, minute and second hands) Date indication Day indication Movement size Diameter Outside:
PARTS LIST / TECHNICAL GUIDE
[SPECIFICATIONS] PARTS LIST / TECHNICAL GUIDE Automatic Item Cal. No. 4R35B/4R36A The figures below are Cal. 4R36A. 3 hands (hour, minute and second hands) Day and Date indication Movement size Diameter
PARTS LIST / TECHNICAL GUIDE Automatic Cal.4R71A
[SPECIFICATION] Item PARTS LIST / TECHNICAL GUIDE Automatic Cal.4R71A Cal. No. 4R71A 3 Hands (Hour, Minute and Second hands) Movement Size Diameter Outside : φ27.4 mm Casing : φ27.0 mm Height : 5.32 mm
Cal. YM92A. φ27.0 mm H 3.7 mm. S.EPSON Products
Cal. YM92A φ27.0 mm H 3.7 mm Items Rev. Page Specifications 03 1 Appearance 00 2 Casing 03 3 Hand fitting 01 4 Hand setting stem 01 5 Dial-01 01 6-01 Dial-02 00 6-02 Dial-03 00 6-03 Dial-04 00 6-04 Casing
Caution for disassembling The hour wheel is made of engineering plastics. When pulling out the hour hand, take care not to damage the hour wheel.
III. REMRKS ON DISSSEMLING ND RESSEMLING Hands Dial Caution for disassembling The hour wheel is made of engineering plastics. When pulling out the hour hand, take care not to damage the hour wheel. How
Cal. VS22A SOLAR SERIES 7 3/ mm. Approx. 6 months. Ø 18.1mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS22A Movement Size 7 3/4 Casing Diameter Ø 18.1mm Height 2.76mm Running Time Approx. 6 months Cal. VS22A Date: 29/Jun./'18 Items Rev. Page Features
7D** Technical Instruction No.1
Assembling the switching unit Set the main plate. 91 Set the main plate. 90 89 88 87 86 85 84 Set the lead pin for RZ1. Set the hour and minute stator. Set the second stator. Set the generating stator.
PARTS CATALOGUE / TECHNICAL GUIDE
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Brand SEIKO Item Cal. No. 7S26B 7S36B Movement Movement size Outside diameter Casing diameter Height (x 1.5) Ø 27.4 mm Ø 27.0 mm 4.9 mm Time indication
Cal. AS32A SOLAR SERIES 10 1/ mm. Approx. 4 months. Ø 23.3mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. AS32A Movement Size 10 1/2 Casing Diameter Ø 23.3mm Height 4.61mm Running Time Approx. 4 months Date: 31/Oct./'16 Cal. AS32A Items Rev. Page Features
Cal.5D22A TECHNICAL GUIDE
No. PROCESS ILLUSTRATIONS AND SPECIAL INSTRUCTIONS ETC. Mount the secondary battery unit. Mount the insulator for secondary battery. Mount the secondary battery guard. Fix the insulator for secondary battery
Cal. VS75A SOLAR SERIES. 4.40mm. Approx. 6 months. Ø 27.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS75A Movement Size 12 Casing Diameter Ø 27.0mm Height 4.40mm Running Time Approx. 6 months Cal. VS75A Date: 1/Sep./'15 Items Rev. Page Features
Cal. VS37A SOLAR SERIES 10 1/ mm. Approx. 6 months. Ø 24.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS37A Movement Size 10 1/2 Casing Diameter Ø 24.0mm Height 2.98mm Running Time Approx. 6 months Date: 15/Dec./'17 Cal. VS37A Items Rev. Page Features
Cal. VS3JA SOLAR SERIES 10 1/ mm. Approx. 6 months. Ø 24.0mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS3JA Movement Size 10 1/2 Casing Diameter Ø 24.0mm Height 3.47mm Running Time Approx. 6 months Date: 2/May/'17 Cal. VS3JA Items Rev. Page Features
Cal. VS17A SOLAR SERIES 5 1/ mm. 2.79mm. Approx. 6 months. Watch Movement Specification and Drawing. Movement Size.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VS17A Movement Size 5 1/2 Casing Diameter 11.8 15.15 mm Height 2.79mm Running Time Approx. 6 months Date: 31/Aug/'17 Cal. VS17A Items Rev. Page
Cal. VR33A CHRONOGRAPH 13 1/ mm. 3 years. Ø 30.6mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing CHRONOGRAPH Cal. VR33A Movement Size 13 1/2 Casing Diameter Ø 30.6mm Height 3.97mm Battery Life 3 years Cal. VR33A Date: 31/Aug./'18 Items Rev. Page Specifications
The chronograph calibres CHRO PC 17 jewels CHRO C12 PC 17 jewels CHRO C12 PC AMPM GMT 17 jewels CHRO PC CAL 17 jewels
Technical guide The chronograph calibres 860 27 CHRO PC 17 jewels 861 27 CHRO C12 PC 17 jewels 910 27 CHRO C12 PC AMPM GMT 17 jewels 930 27 CHRO PC CAL 17 jewels o 27.00 mm / Power-reserve Jewel number
2. Uncasing. 5. Remove the clamp screws (casing ring / middle and movement / casing ring) and the clamps. 6. Remove the casing ring.
Calibre 360 1. Presentation 2. Uncasing 3. Chronograph movement (module) / M2 replacement procedure 4. Overhauling the base movement 5. Assembling the base movement with the chronograph movement 6. Chronograph
Cal. VR43A SOLAR SERIES 13 1/ mm. Approx. 4 months. Ø 30.6mm. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing SOLAR SERIES Cal. VR43A Movement Size 13 1/2 Casing Diameter Ø 30.6mm Height 4.52mm Running Time Approx. 4 months Date: 30/Nov./'17 Cal. VR43A Items Rev. Page Features
CALIBRE Q SCS CAL CORH CORM CORS 7 jewels Description et performances
Technical guide CALIBRE 1370 25.60 Q SCS CAL CORH CORM CORS 7 jewels Description et performances The caliber 1370, destined for a man's electronic watch with analogical display, is fitted with a quartz
CALIBRE 1387 R 13 Q CORH CORM
Description CALIBRE 1387 R 13 Q CORH CORM 3 jewels (13 x 15.15 x 2.3) 13.00 x 15.15 mm Movement height 2.30 mm Jewel number Frequency 3 32'768 A/h GENERAL DESCRIPTION A new design in quartz watches with
automatic, with center sweep-second automatic, calendar with center sweep-second automatic, day and date with center sweep-second
DIAL SIDE TRAIN SIDE Scale 1:1 Specifications Movement Automatic mechanism 11112 Ligne, lever escapement Diameter of the plate 25.60 mm Unbreakable and self-lubricated mainspring Total running time: 42
Calibre General information for Calibre Exploded views for calibre Specific information for calibre
Technical Guide TG-19-C-024-E C Produced by : pelrom Date: 20.09.2010 3 Modifications: see last page CALIBRE 3220 Version A 131/4 Ø 30 mm Height on movement Power reserve Number of jewels Frequency Lift
BULOVA MODELS. Specifications. Designation of Types. 11 AOAC 11 AOACB Automatic 11 AOACD. Date. Movement DIAL SIDE TRAIN SIDE.
DIAL SIDE TRAIN SIDE BULOVA MODELS 11 AOAC 11 AOACB 11 AOACD Date Day + Date Scale 1:1 Specifications Movement 11y,'" Lever escapement 17 or 23 jewels Unbreakable and self-lubricated mainspring Total running
TECHNICAL INFORMATION INFORMACION TECNICA
TECHNICL INFORMTION INFORMCION TECNIC CITIZEN QURTZ Cal. No. E76 (Cal. No. E760) ENGLISH Contents 1. FETURES...1 2. BEFORE USING...1 3. SPECIFICTIONS...2 4. SETTING THE TIME ND DTE...3 5. FUNCTIONS UNIQUE
Special Points. Specifications TRAIN SIDE DIAL SIDE. Scale 2V2:1
DAL SDE TRAN SDE Scale 2V2:1 Specifications 7% ligne, lever escapement Diameter of plate 17.20 mm. Total running time: 47 hours Screwless beryllium 21,600 beats per hour Adjustable stud holder balance
Cal. Y121E STANDARD 6 3/ mm. 2.99mm. 2 years. Watch Movement Specification and Drawing. Movement Size. Casing Diameter.
Watch Movement Specification and Drawing STANDARD Cal. Y121E Movement Size 6 3/4 8 Casing Diameter 15.3 17.8 mm Height 2.99mm Battery Life 2 years Cal. Y121E Date: 20/Oct./'14 Items Rev. Page Specifications
SECTION 9 CRANKING SYSTEM CONTENTS
SECTION 9 CRANKING SYSTEM CONTENTS 9-1. 9-2. 9-3. 9-4. 9-5. 9-6. 9-7. 9-8. GENERAL DESCRIPTION.,...,..., 9-2 SPECIFICATIONS.......................................... 9-4 LUBRICATION 9-5 REMOVAL AND INSTALLATION...
TECHNICAL INFORMATION
TECHNICAL INFORMATION PRODUCT P 1/ 11 Model No. Description TM3010C Multi tool L CONCEPT AND MAIN APPLICATIONS Model TM3010C has been developed based on model TM3000C and equipped with the tool-less accessory
Specific information for calibre 3603
Fig. 1.0 1.0 Assembling of date indication 1. Stem in position 3 : Turn anti-clockwise the driving wheel for date unlocking yoke (reference 33029) until the finger of this wheel is aligned with the pin,
./#0#. 1"&." 1994 ELECTRICAL Suzuki of America Corp. - Starters. Swift
!"" #$%!& '()!)((*(+,*)- 1994 ELECTRICAL Suzuki of America Corp. - Starters Swift Two types of starter motors are used, conventional and reduction gear. Both types of starters consist of yoke assembly,
Reference number: Worksheet/Receipt. Owners name: - Telephone: Description of item(s) received, including accessories:
Worksheet/Receipt Owners name: - Address: n/a Telephone: n/a Description of item(s) received, including accessories: Rotary quartz head only. Work required based on initial inspection: Watch does not run
RONDA normtech 700 & Caliber 6004.B 11½''' Long battery-life and special functionality. Features. Product Specifications. Analog quartz movement
RONDA normtech 700 & 6000 Long battery-life and special functionality Caliber 6004.B 11½''' Product Specifications Features Analog quartz movement Repairable metal watch movement Line normtech Caliber
Servicing a Poljot 3133 movement
Servicing a Poljot 3133 movement A service guide made by WUS member SLLS, June 2015 Editor: WUS member Polmax3133 Use this guide at your own risk. To dismantle a 3133 movement, just start at the end of
Masnory Drill. Power Tool Accessories
DMD3YG840MC7030HB 3 70 30 DMD4YG840MC7030HB 4 70 30 DMD5YG840MC8545HB 5 85 45 DMD6YG840MC10050HB 6 100 50 DMD7YG840MC10050HB 7 100 50 DMD8YG840MC12070HB 8 120 70 DMD9YG840MC12070HB 9 120 70 DM0YG840MC12070HB
Technical Guide TG-19-C-053-E C. Prod. by: pelrom Date: Modifications: see last page CALIBRE 1532
Technical Guide TG-19-C-053-E C Prod. by: pelrom Date: 24.10.2008 3 Modifications: see last page CALIBRE 1532 Version A Version B Version C Version D 11 1/2 Ø 25,60 mm 1 2 3 ASS E.O.L COR Height on movement
GRAND UNION CANAL UXBRIDGE WEST LONDON UB8 2GH. Accommodation schedule. Block B
Block B B 0.1 Ground 2 81.64 878 1,550 B 0.2 Ground 2 65.38 703 1,450 B 0.3 Ground 2 75.23 809 1,500 B 0.4 Ground 1 51.55 554 1,250 B 0.5 Ground 1 55.34 595 1,275 B 0.6 Ground 1 52.9 569 1,250 B 0.7 Ground
PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS
PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS NON-REVERSING HANDLE ASSEMBLY (SERIAL NO S. STARTING WITH B & D ) Fig. Part Form A278F Date 10-00/B Page 1 of 6 4. 14309 Ring O 5. 14312 Ring
METAL MOVEMENT MADE IN JAPAN
2018-2019 METAL MOVEMENT MADE IN JAPAN Cal. 2035 2035 the representative movement of MIYOTA. After the 2035 has appeared to the market, a lot of brands is using regularly all over the world. JAPAN MOVEMENT
All information contained in this booklet and referring to Series 245 includes ser. 246, unless otherwise noted. and French.
.'. All information contained in this booklet and referring to Series 245 includes ser. 246, unless otherwise noted. \ DAL SDE TRAN BRDGE SDE (ndicators Removed) (Magnetic Shield Removed) CALBER NO. Fig.
Technical Guide TG-19-C-074-E A CALIBRE Thermo-compensated
Technical Guide TG-19-C-074-E A Produced by : selrom Date : 19.07.2011 CALIBRE 5666 Version A 15 Ø 34.60 mm P4 P1 P3 P2 Version Thermo-compensated Height of movement 13.30 mm Number of jewels 9 Exclusive
1 Overview. Technical Data of Main Performance. Engine Number Position: Overview -1- Frame Number. Name Plate Engine Number.
1 Engine Number Position Maintenance Precautions Technical Data of Main Performance Standard Torque Values Bar Tool Maintenance Period Table Wiring Diagram Symbol Descriptions Engine Number Position Photo
Manual Transmission (M2S5,M3S5) General Troubleshooting... MTA - 2 Specification... MTA - 9
Manual Transmission (M2S5,M3S5) General Troubleshooting... MTA - 2 Specification... MTA - 9 Manual Transmission Description and Operation... MTA - 13 Components... MTA - 19 Inspection... MTA - 20 Removal...
INSTRUCTIONS BENCH TYPE COIL WINDER DRIVES MODELS: 2057, 2067, AND 2069
INSTRUCTIONS BENCH TYPE COIL WINDER DRIVES MODELS: 2057, 2067, AND 2069 The Crown bench type Coil Winder Drive is small, rugged and durable unit used for winding coils from the smallest solenoid type to
VB 16Y VB 16Y POWER TOOLS PORTABLE REBAR CUTTER/BENDER TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL VB 16Y POWER TOOLS PORTABLE REBAR CUTTER/BENDER VB 16Y TECHNICAL DATA AND SERVICE MANUAL V LIST No. 0790 Sep. 2001 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT REMARK: Throughout
ECEg439:-Electrical Machine II
ECEg439:-Electrical Machine II 2.2 Main Structural Elements of DC Machine Construction of DC Machines A DC machine consists of two main parts 1. Stationary Part (Stator):-It is designed mainly for producing
TABLE OF CONTENTS. Cordless Impact Driver. Model No. EY7542. Europe Oceania
Order Number PTD0707X38CE Cordless Impact Driver Model No. EY7542 Europe Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications -----------------------------------------------------
VB 13Y VB 13Y POWER TOOLS PORTABLE REBAR CUTTER/BENDER TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL VB 13Y POWER TOOLS PORTABLE REBAR CUTTER/BENDER VB 13Y TECHNICAL DATA AND SERVICE MANUAL V LIST No. 0782 Jan. 2000 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT REMARK: Throughout
STARTER - HITACHI Isuzu Trooper II DESCRIPTION TESTING STARTER PERFORMANCE TESTS Starters HITACHI. Isuzu
STARTER - HITACHI 1986 Trooper II 1984 Starters HITACHI DESCRIPTION Starter is a conventional 12-volt, 4-pole brush-type motor, with direct or reduction gear drive. The starter-mounted solenoid shifts
SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS ELECTRIC CHAIN HOISTS 9560, 9561, 9562, 9565, 9566, 9567,
SERVICE PARTS LIST PAGE 1 OF 5 BULLETIN NO. 54-02-1202 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
REMOVAL & INSTALLATION
Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip
STARTING SYSTEM LOCATION INDEX [LF]
![STARTING SYSTEM LOCATION INDEX [LF]](/thumbs/75/72592935.jpg "STARTING SYSTEM LOCATION INDEX [LF]")
1. Remove the battery cover. 2. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [LF].) 3. Remove the side cover. (LH) 2007 Mazda MX-5 Miata Sport 2007 ENGINE Starting System -
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower
DIRECT DRIVE: THE REMARKABLE BULOVA ACCUTRON CALIBER 214
Lehekülg 1/5 13.05.2013 1:04 Search DIRECT DRIVE: THE REMARKABLE BULOVA ACCUTRON CALIBER 214 By Walt Odets Site Map TimeZone Italia Login / Register Register for TimeZone! Registering provides access to
A/C COMPRESSOR SERVICING Article Text 1991 Saab 9000 For Copyright 1997 Mitchell International Friday, October 15, :22PM
Article Text ARTICLE BEGINNING 1991 GENERAL SERVICING Compressor Service * PLEASE READ THIS FIRST * CAUTION: When discharging air conditioning system, use only approved refrigerant recovery/recycling equipment.
1983 Mazda RX-7 GSL TUNE-UP' 'Mazda Rotary
TESTING ENGINE COMPRESSION The manufacturer recommends using a special compression tester (49 0820 280K). Compression testers for piston engines will read only the highest pressure of the 3 combustion
HKS 700E. Service Manual June Ver. 2.04
HKS 700E Service Manual 009 June Ver..04 HKS CO.,LTD 78 KITAYAMA FUJINOMIYA SHIZUOKA JAPAN 48-09 TEL +8(0)544-54-78 FAX +8(0)544-54-40 hks_aviation@hks-power.co.jp http://www.hks-power.co.jp/hks_aviation/
DC 120VA DC 120VA POWER TOOLS DIAMOND CORE DRILL TECHNICAL DATA AND SERVICE MANUAL MODEL
MODEL DC 120VA POWER TOOLS D DIAMOND CORE DRILL DC 120VA TECHNICAL DATA AND SERVICE MANUAL LIST No. 0192 Jun. 2000 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT Notice for use Specifications
ON-VEHICLE INSPECTION
CH2 P11586 CHARGING CHARGING SYSTEM ONVEHICLE INSPECTION 1. CHECK BATTERY ELECTROLYTE LEVEL Check the electrolyte quantity of each cell. MaintenanceFree Battery: CH03L01 If under the lower level, replace
AUT 125 ELECTRICAL II CH 54 & 55 CHARGING SYSTEMS
Name: Class: Date: AUT 125 ELECTRICAL II CH 54 & 55 CHARGING SYSTEMS Multiple Choice Identify the choice that best completes the statement or answers the question. 1. Technician A says that the diodes
SECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Forward Clutch Assembly... 307-01-2 307-01-2 Automatic Transaxle/Transmission
1991 Mazda MX-5 Miata. STARTER - DIRECT DRIVE ELECTRICAL Mazda Starters - Direct Drive ELECTRICAL Mazda Starters - Direct Drive
DESCRIPTION STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive Nippondenso direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is attached
Press release. Patek Philippe Geneva October 2014
Press release Patek Philippe Geneva October 2014 Patek Philippe Multi-Scale Chronograph Refs. 5975 and 4675 The chronograph: a measuring instrument par excellence Chronographs for measuring time intervals
ALTERNATOR - HITACHI
ALTERNATOR - HITACHI 1986 Isuzu Trooper II 1986 Alternators & Regulators HITACHI ALTERNATORS Isuzu DESCRIPTION Hitachi alternators are conventional 3-phase, self-rectifying alternators. Three positive
MODEL D 10YB POWER TOOLS TECHNICAL DATA AND SERVICE MANUAL ANGLE DRILL D 10YB SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
MODEL D 10YB POWER TOOLS D ANGLE DRILL D 10YB TECHNICAL DATA AND SERVICE MANUAL LIST No. 0193 Jun. 2000 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT Notice for use Specifications and
Rheometer Calibration Fixture Instruction Manual Model 280 & 286
Rheometer Calibration Fixture Instruction Manual Model 280 & 286 Instruction Manual Part No. 204210 Revision B Copyright 2009 Fann Instrument Company Houston, Texas, U.S.A. All rights reserved. No part
MOTORS. Part 2: The Stepping Motor July 8, 2015 ELEC This lab must be handed in at the end of the lab period
MOTORS Part 2: The Stepping Motor July 8, 2015 ELEC 3105 This lab must be handed in at the end of the lab period 1.0 Introduction The objective of this lab is to examine the operation of a typical stepping
SERVICE MANUAL MR-3024/3025/3028 REVERSING AUTOMATIC DOCUMENT FEEDER
SERVICE MANUAL REVERSING AUTOMATIC DOCUMENT FEEDER MR-04/05/08 Model: MR-04/05 Publish Date: April 0 File No. SME000B0 R0L060-TTEC Ver0 F_04-04 Trademarks Molykote is a registered trademark of Dow Corning
Models: PMG A and PMG P
Models: PMG 3.0-250-A and PMG 2.0-250-P 1/6 AXCO AF-PM-2-D generators Models: PMG 3.0-250-A and PMG 2.0-250-P Technical Data Sheet Permanent Magnet Generator for Distributed Wind Power Applications AXCO-Motors
Electrical Motor Controls Chapter 4 (Fourth Edition) Chapter 2 (Fifth Edition)
Electrical Motor Controls Chapter 4 (Fourth Edition) Chapter 2 (Fifth Edition) 1. Which drawing type shows physical details as seen by the eye? 2. Which drawing is similar to a pictorial drawing but has