UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
|
|
- Audra Eleanor Webster
- 5 years ago
- Views:
Transcription
1 SECTION METERS AND GAUGES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 ABBREVIATIONS A. Degree or degrees. B. AFF Above Finished Floor. C. BAS Building Automation System D. F Fahrenheit. E. GPM Gallons Per Minute. F. ma Milliamp, or Milliamps. G. PSI Pounds per Square Inch. H. PSIG Pounds per Square Inch Gauge. I. V Volt, or Volts 1.3 SUBMITTALS A. Product Data: For each type of product indicated. B. Wiring Diagrams: For power, signal, and control wiring. C. Operation and Maintenance Data: For meters and gages to include in operation and maintenance manuals. PART 2 - PRODUCTS 2.1 THERMOMETERS A. Available Manufacturers: METERS AND GAUGES FOR HVAC PIPING
2 1. Flo Fab Inc. 2. Miljoco Corporation. 3. Palmer Wahl Instrumentation Group. 4. Tel-Tru Manufacturing Company. 5. Trerice, H. O. Co. 6. Weiss Instruments, Inc. 7. Winters Instruments - U.S. B. Standard: ASME B C. Case: Cast aluminum D. Size: 12 nominal unless otherwise indicated. E. Case Form: Adjustable angle. F. Tube: Glass with magnifying lens and blue or red organic liquid. Mercury is not acceptable. G. Tube Background: Nonreflective aluminum with permanently etched scale markings graduated in 2 F increments. H. Window: Glass. I. Stem: 1. Duct Installation: Aluminum ventilated. 2. Pipe Installation: Brass. J. Thermowell Connector for Pipe Installation: 1¼ with ASME B1.1 threads. K. Accuracy: Plus or minus one scale division. L. Scale Range: Suitable for service. 2.2 DUCT THERMOMETER MOUNTING BRACKETS A. Description: Flanged bracket with screw holes for attachment to air duct and made to hold thermometer stem. 2.3 THERMOWELLS A. Thermowells: 1. Standard: ASME B Description: Manufactured by thermometer manufacturer, pressure-tight, socket-type fitting made for insertion into piping tee. 3. Material: METERS AND GAUGES FOR HVAC PIPING
3 a. Copper Tubing/Piping: Brass. b. Steel Piping: Type 316 stainless steel 4. Type: Stepped shank unless straight or tapered shank is recommended by manufacturer. 5. Bore: Diameter required to match thermometer stem. 6. Insertion Length: Length required to match thermometer stem and to reach center of pipe. 7. Lagging Extension: Include for insulated piping and tubing. 8. Heat transfer medium: As available and recommended by manufacturer. 2.4 PRESSURE GAGES 1. Available Manufacturers: a. Ernst Flow Industries. b. Flo Fab Inc. c. Palmer Wahl Instrumentation Group. d. Tel-Tru Manufacturing Company. e. Trerice, H. O. Co. f. Watts Regulator Co.; a div. of Watts Water Technologies, Inc. g. Weiss Instruments, Inc. 2. Application Standard: ASME B Case: Dry, field liquid fillable, satin finished, type 304 stainless steel, stem mounted, flangeless. 4. Pressure-Element Assembly: Bronze tube. 5. Pressure Connection: Brass, with ¼ or ½ ASME B pipe threads and bottomoutlet unless back-outlet is indicated. 6. Movement: Stainless steel. 7. Dial Size: 6 8. Dial Face: Nonreflective aluminum with permanently etched black scale markings graduated in psi. Two PSI maximum per graduation. 9. Pointer: Adjustable black metal. 10. Window: Glass. 11. Ring: 304 stainless steel. 12. Accuracy: Grade 1A, plus or minus 1 percent of full scale. 13. Units: PSI 14. Scale range: Suitable for service 2.5 GAGE ATTACHMENTS A. Pulsation Dampener: ASME B40.100, brass; with ¼ or ½, ASME B pipe threads and piston type surge-dampening device. Include extension for use on insulated piping. B. Siphons: Loop-shaped section of brass for copper, and stainless steel for steel, pipe filled with water with ¼ or ½ pipe threads to prevent live steam from entering gauge. Provide on all gauges serving steam systems. METERS AND GAUGES FOR HVAC PIPING
4 C. Valves: Brass needle for copper pipe, or stainless-steel needle for steel pipe, with ¼ or ½, ASME B pipe threads. 2.6 TEMPERATURE/PRESSURE PLUG A. Available Manufacturers: 1. Flow Design, Inc. 2. Trerice, H. O. Co. 3. Watts Regulator Co.; a div. of Watts Water Technologies, Inc. 4. Weiss Instruments, Inc. B. Description: Test fitting made for insertion into piping tee fitting. C. Body: Brass or stainless steel with core inserts and gasketed and threaded cap. Include extended stem on units to be installed in insulated piping. D. Thread Size: ½, ASME B pipe thread. E. Minimum Pressure and Temperature Rating: 500 psig at 200 F. F. Core Inserts: EPDM self-sealing rubber. 2.7 TEMPERATURE/PRESSURE PLUG KITS A. Available Manufacturers: 1. Flow Design, Inc. 2. Trerice, H. O. Co. 3. Watts Regulator Co.; a div. of Watts Water Technologies, Inc. 4. Weiss Instruments, Inc. B. Provide one temperature/pressure plug kit containing two thermometers, one pressure gauge, pressure gauge adapter, and carrying case. Thermometer sensing elements, pressure gauge, and gauge adapter probes shall be of a diameter to fit temperature/pressure plugs and of length to project into piping. C. Low Range Thermometer: Small, bimetallic insertion type with 1 to 2 diameter dial and tapered-end sensing element. Dial range shall be at least 25 to 125 F. D. High Range Thermometer: Small, bimetallic insertion type with 1 to 2 diameter dial and tapered-end sensing element. Dial range shall be at least 0 to 220 F. E. Pressure Gage: Small, Bourdon-tube insertion type with 2 to 3 diameter dial and probe. Dial range shall be at least 0 to 200 PSIG. F. Carrying Case: Metal or plastic, with formed instrument padding. METERS AND GAUGES FOR HVAC PIPING
5 PART 3 - EXECUTION 3.1 INSTALLATION A. Thermowells: 1. In all locations install so thermometer will be easily visible. 2. In horizontal piping install with socket extending to center of pipe and in vertical position in piping tees. 3. In vertical piping install with socket extending to center of pipe and in horizontal position in piping tees. B. Install thermowells of sizes required to match thermometer connectors. C. Install thermowells with lagging extension on insulated piping. D. Fill thermowells with heat-transfer medium as recommended by manufacturer. E. Install thermometers in thermowells and adjust vertical and tilted positions so they are with-in 15 (Measured from 6 above the floor) of an easily accessible location and the window is perpendicular to that location. 1. Exception: Where installed in piping or ductwork located in excess of 20 AFF. F. Install duct-thermometer mounting brackets in walls of ducts. Attach to duct with screws. G. Install thermometers in the following locations: 1. Where indicated 2. Inlet and outlet of each hydronic zone. 3. Inlet and outlet of each hydronic boiler. 4. Inlet(s) and outlet(s) of each chiller. 5. Inlet and outlet of each hydronic coil in air-handling units. 6. Inlet(s) and outlet(s) of each hydronic heat exchanger. 7. Inlet and outlet of each thermal-storage tank. 8. Outside, return, and supply air ducts. H. Install pressure gages in piping tees with pressure gage located on pipe at the most readable position. I. Install pressure gages in the following locations: 1. Inlet an outlet of each pressure-reducing valve. 2. Inlet and outlet of each chiller. 3. Inlet and outlet of each boiler. 4. Inlet and outlet of each coil. a. Exceptions (Install test plugs instead): 1) Fan coil units. 2) Variable volume terminal units. 3) Blower coil units. METERS AND GAUGES FOR HVAC PIPING
6 5. Inlet of each thermal-storage tank. 6. Suction and discharge of each pump. J. Install valve in piping for each pressure gage. K. Install snubber in piping for each pressure gage for fluids (except steam). L. Install siphon fitting in piping for each pressure gage (for steam). M. Install test plugs in piping tees where indicated and at all pipe mounted BAS pressure and temperature sensors. 3.2 CONNECTIONS A. Install meters and gages adjacent to machines and equipment to allow service, maintenance, and cleaning of meters, gages, machines, and equipment. B. Connect flowmeter elements to meters. C. Connect flowmeter transmitters to meters. 3.3 ADJUSTING A. After installation, calibrate meters according to manufacturer's written instructions. B. Adjust faces of meters and gages to proper angle for best visibility. END OF SECTION METERS AND GAUGES FOR HVAC PIPING
SECTION METERS AND GAUGES. 0.1 All meters and electronic gauges shall be able to communicate with the current BAS System (Johnson METASYS).
SECTION 15122 - METERS AND GAUGES PART 1 GENERAL 0.1 All meters and electronic gauges shall be able to communicate with the current BAS System (Johnson METASYS). 1.1 RELATED DOCUMENTS A. Drawings and general
More informationSAMPLE PRODUCT SPECIFICATIONS
SAMPLE PRODUCT SPECIFICATIONS Thermometers & Gauges Product Guide Specification THERMOMETERS & GAUGES Specifier Notes: This section covers Miljoco Corporation thermometers and pressure gauges suitable
More informationSECTION METERS AND GAGES FOR HVAC PIPING
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. 1.2 SUMMARY A. This
More informationSECTION METERS AND GAGES FOR PLUMBING PIPING
PART 1 GENERAL 1.01 SECTION INCLUDES A. Positive displacement meters. B. Flow meters. SECTION 22 0519 METERS AND GAGES FOR C. Pressure gages and pressure gage taps. D. Thermometers and thermometer wells.
More informationGuide Specification SECTION HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY
SECTION 23 21 16 - HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Air
More informationSECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY
SECTION 230533 - PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Static pressure
More informationSECTION METERS AND GAUGES FOR HVAC PIPING
SECTION 23 05 19 METERS AND GAUGES FOR HVAC PIPING PART 1 - GENERAL 1.1 SUMMARY A. Work included: Provision of materials, installation and testing of: 1. Thermometers 2. Thermometer Wells 3. Differential
More informationSECTION METERS AND GAUGES
SECTION 22 05 19 PART 1 GENERAL 1.1 DESCRIPTION OF WORK: A. Extent of meters and gauges required by this section is indicated on drawings and/or specified in other Division-22 sections. B. Types of meters
More informationSteam & Hot Water INSTRUMENTS. Adjustable Angle Industrial Thermometer. Econo Thermometer. ] Aluminum Stem. ] Air-Duct Stem
Adjustable Angle Industrial Thermometer Recognized globally as the Trerice BX Industrial Thermometer, this is an instrument of extreme accuracy and rugged dependability. Available in scale lengths of 7"(AX),
More informationA. Provide all HVAC specialties required to complete the installation of all HVAC systems. B. Manufacturers: Refer to individual product item.
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION 23 05 02 PART 1 GENERAL 1.01 DESCRIPTION A. Provide all HVAC specialties required to complete the installation of all HVAC systems.
More informationADJUSTABLE ANGLE THERMOMETERS
ADJUSTABLE ANGLE THERMOMETERS Commercial grade units available with 9" aluminum or plastic cases, spirit fill, and 3½" or 6" stems. Unit can be adjusted for easy reading at any angle. SPECIFICATIONS Case:
More informationDARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
PART DESIGN DIRECTIVE. QUALITY ASSURANCE SECTION 530 METERS AND GAGES A. Comply with applicable UL standards pertaining to meters and gages and with applicable portions of ASME and Instrument Society of
More informationGLASS INDUSTRIAL THERMOMETERS
TEL-TRU MANUFACTURING COMPANY GLASS INDUSTRIAL THERMOMETERS World -Class Thermometers Since 1916 www.teltru.com Glass Industrial Thermometers Tel-Tru Glass Industrial Thermometers are used on pipelines
More informationINTRODUCTION. Catalog 898 covers one of the broadest lines of remote reading thermometers available anywhere in the world.
INTRODUCTION Miljoco Corporation is an international manufacturer of indicating temperature and pressure instruments and was founded in 1979 by Howard M. Trerice. Presently, its headquarters are located
More informationTemperature Regulators
Temperature Regulators DESIGN & OPERATION DIAL THERMOMETER (Model 91400 only) BELLOWS OVERRANGE PROTECTION SPRING CAPILLARY TUBING CONNECTION SENSING BULB RANGE ADJUSTMENT SPRING CAP ADJUSTMENT SCREW BUSHING
More informationSECTION HVAC WATER PIPING ACCESSORIES
SECTION 23 05 10 PART 1 - GENERAL HVAC WATER PIPING ACCESSORIES 1.01 RELATED DOCUMENTS 1.02 SCOPE A. The requirements of the General Conditions, Supplementary Conditions, Division 1, Division 20, and Drawings
More informationW91/W94 Series TEMPERATURE REGULATORS. Self-Operated Temperature Regulators. Design & Operation W91 Non-Indicating W94 Dial Thermometer
Design & Operation W91 Non-Indicating W94 Dial Thermometer Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company CAPILLARY
More informationTBM. Bi-Metal Thermometer
Description & Features: A general purpose, versatile 1 (25mm) to 6 (150mm) dial, 304 stainless steel thermometer Bi-metallic sensing element for reliable readings Back, bottom or adjustable angle connection
More informationA. Valves and specialties including necessary accessories indicated on drawings and specified in this section.
SECTION 15081 - VALVES AND SPECIALTIES (HVAC) PART - 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More information* T Temperature-Indicating Dial (Must be field set and calibrated to an actual thermometer)
175/153 Series Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2006 Watson McDaniel Company 175 HEATING 153 COOLING 175 / 153 Screwed Connection
More informationJHawk Instrument Inc. warrants the
Warranty Statement JHawk Instrument Inc. warrants the component parts and workmanship of its products under normal use and service for a period of one year from the date of the shipment. All obligations
More information1 (25mm): Acrylic Others: Glass standard, hermetically sealed
Description & Features: A general purpose, versatile 1" (25mm) to 6" (150mm) dial, 304 stainless steel thermometer Bi-metallic sensing element for reliable readings Back, bottom or adjustable angle connection
More informationTEMPERATURE REGULATORS W91/W94 Series
Self-Operated Temperature Regulators Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company Self-Operating Design Indicating
More informationTBM. Bi-Metal Thermometer
Description & Features: A general purpose, versatile 1 (25mm) to 6 (150mm) dial, 304 stainless steel thermometer Bi-metallic sensing element for reliable readings Back, bottom or adjustable angle connection
More information300/400/ /900 SERIES
Dial Indicating Thermometers Vapor Actuated Remote 300/400/600 700/900 SERIES Indicates media temperature using a temperature-actuated liquid in the sensing element and a highly accurate, high quality
More informationMEASUREMENT SOLUTIONS FOR THE WATER & WASTEWATER INDUSTRY
MEASUREMENT SOLUTIONS FOR THE WATER & WASTEWATER INDUSTRY MUNICIPAL AND INDUSTRIAL WATER & WASTEWATER PROCESSING NOSHOK provides pressure, level and temperature measurement solutions, along with diaphragm
More informationCSP PSYCHIATRIC SERVICES UNIT SECTION METERS AND GAUGES FOR HVAC PIPING
SECTION 23 05 19 METERS AND GAUGES FOR HVAC PIPING PART 1 GENERAL 1.1 SUMMARY A. Section includes 1. Digital Thermometers. 2. Pressure Gauges. 3. Test Plugs and Kits. 1.2 DEFINITIONS A. CR: Chlorosulfonated
More informationSECTION VALVES PART 1 -GENERAL
SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This
More informationGeneral Service Gauges
Utility HVAC Diaphragm General Service Gauges The Weiss Series TL Gauges are intended for general service conditions, for pressure or vacuum on air, oil, water, gas or other mediums that do not attack
More informationGeneral Service Gauges
Utility HVAC Diaphragm General Service Gauges The Weiss Series TL Gauges are intended for general service conditions, for pressure or vacuum on air, oil, water, gas or other mediums that do not attack
More informationUniversity of Delaware
SECTION 23 36 00 _ SUMMARY PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Constant/Variable volume supply terminal units. 2. Fan powered terminal units. 3. Exhaust valves B. Related Sections: Section
More informationKEL DIFFERENTIAL PRESSURE FLOWMETERS
KEL DIFFERENTIAL PRESSURE FLOWMETERS Flow Pressure Level Temperature measurement monitoring control Rugged Metal Construction Flow Rate to 2000 GPM Linear Scale For Horizontal or Vertical Pipes Threaded
More informationTBM. Bi-Metal Thermometer
Description & Features: A general purpose, versatile 1" (25mm) to 6" (150mm) dial, 304 stainless steel thermometer Bi-metallic sensing element for reliable readings Back, bottom or adjustable angle connection
More informationDivision 23 - HVAC Section Switzerland Beallsville K-12 GENERAL DUTY VALVES FOR HVAC PIPING
SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division
More informationSOLAR HEATING SYSTEM
SECTION 13600 SOLAR HEATING SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 07600 - Flashing and Sheet Metal. 2. 07900 - Joint Sealers. 3. 15260 - Thermal Insulation (Plumbing). 4. 15410 - Piping
More informationTemperature Measurement Solutions. Dial Indicating Electronic Industrial RTDs Thermowells Accessories
Temperature Measurement Solutions Dial Indicating Electronic Industrial RTDs Thermowells Accessories At NOSHOK, we pride ourselves on being innovators in the industry by continually offering the latest
More informationSECTION GENERAL-DUTY VALVES FOR HVAC PIPING. A. Contents of Division 23, HVAC and Division 01, General Requirements apply to this Section.
SECTION 23 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Gate Valves 2. Balancing Valves 3. Ball Valves 4. Butterfly Valves 5. Swing Check Valves 1.2 RELATED SECTIONS A. Contents of Division
More information2 1 /2" Glycerin-Filled Dual Scale Vacuum Gauges
BAC-25 Brass Case Dial Size: 2 1 /2" Glycerin Filled Pressure Ranges: 30" HG to 15,000 PSI/Bar (Dual Scale) Accuracy: Within 1.5% of Maximum Graduation Case: Forged Brass With Polished Brass ABS Bourdon
More informationPowers Controls Powertop Two-Way Valves Normally Open
Powers Controls Powertop Two-Way s Normally Open VP 658-5 Description The VP 658 normally open valves are pneumatically operated valves designed to control the flow of both water and steam. Features Stainless
More informationMarsh Instruments. STD Pocket Thermometer. Digital Pocket Thermometer. Specifications. Specifications. Gas Pressure Test Set. belgas.
Marsh Instruments STD Pocket Thermometer 1" Dial 304SS Hermetically Sealed Case 5" long stem Protective Case with SS Clip Digital Pocket Thermometer 3.5 Digital LCD display ABS Plastic Case 5" long stem
More informationMarsh Instruments. Marshalltown Value Series Gauge. Specifications. X-Mas Tree Gauge. Specifications. belgas.net 1
Marsh Instruments Marshalltown Value Series Gauge ASME Grade B Extra Savings with Quantity Pricing 4 Standard Mounting Options: LM, CB, Right & Left (1.5" Only) Marshalltown Value Series are the most economical,
More informationTel-Tru Manufacturing Company World-Class Thermometers
Tel-Tru Manufacturing Company World-Class Thermometers We manufacture thermometers - but we sell service, reliability, product quality and performance. QUALITY AND PERFORMANCE FEATURES: CASE AND BEZEL
More informationWINTERS INSTRUMENTS MANUFACTURER OF INDUSTRIAL INSTRUMENTATION
Process Industry Products www.winters.com MANUFACTURER OF INDUSTRIAL INSTRUMENTATION PPc Process Gauge The PPC series gauge is a durable instrument with a phenolic solid front and blowout back. Use the
More informationSECTION PUMPS GENERAL PUMPS PART RELATED DOCUMENTS
SECTION 15160 - PUMPS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Basic Requirements: Provisions of Section 15010, BASIC MECHANICAL REQUIREMENTS and Section 15030, ELECTRICAL REQUIREMENTS FOR MECHANICAL
More informationGas Actuated Thermometers
Gas Actuated Thermometers 401 Gas Actuated Thermometers Operating & Installation Gas actuated thermometers fall within Class IV, gas-filled with absorbent definition. They use a thermal system filled with
More informationSECTION PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL
SECTION 22 10 10 PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and
More informationDescription & Features: Applications:
Description & Features: Most economical, all-purpose pressure gauge.5" (40mm) to 4" (00mm) sizes Friction bezel rings Black steel case Brass internals ±3-2-3% accuracy CRN registered 5 year warranty Applications:
More informationB. Base occupied space sound level estimates on ARI 885. C. Terminal heating coils shall conform to ARI 410.
PART 1 - GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
More informationPRODUCT OVERVIEW A Trusted Advisor and Supplier for the Oil, Energy, Mining and Industrial Sectors
Proud member of the Unified Valve Group PRODUCT OVERVIEW A Trusted Advisor and Supplier for the Oil, Energy, Mining and Industrial Sectors May/2014 Proud member of the Unified Valve Group PRODUCTS TO TRUST
More informationProcess Industry. Specification Guide. For. Pressure & Temperature Instruments & Related Accessories
Process Industry Specification Guide For Pressure & Temperature Instruments & Related Accessories Prepared for Consultant, Design & Specification Engineers Gauges Differential Gauge (PDT) 1. The pressure
More informationPROJ. NO SECTION HYDRONIC PUMPS
SECTION 23 21 23 HYDRONIC PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationTHE HISTORY OF WEKSLER GLASS THERMOMETER CORPORATION
THE HISTORY OF WEKSLER GLASS THERMOMETER CORPORATION Weksler Glass Thermometer Corporation has a long and proud history. Our founder, Harry Weksler, was an accomplished glass blower who left England in
More informationGAUGE ACCESSORIES SY-14B
GAUGE ACCESSORIES PSN 25NVBR SY-14B TC-14 LC-14 BV25 TABLE 1 - PRESSURE SNUBBERS HOUSING HOUSING NPT PSI RATING STYLE CODE MATERIAL CODE MATERIAL CODE NPT AT 70 F PSN B Brass 25 1/4" 1,500psi S 303 S.S.
More informationMarsh Instruments. Marshalltown Value Series Gauge. Specifications. X-Mas Tree Gauge. Specifications. belgas.net 1
Marsh Instruments Marshalltown Value eries Gauge AME Grade B Extra avings with Quantity Pricing 4 tandard Mounting Options: LM, CB, Right & Left (1.5" Only) Marshalltown Value eries are the most economical,
More information***************************************************************************************************************
15515 VALVES, HANGERS, AND SPECIALTIES *************************************************************************************************************** SPECIFIER: CSI MasterFormat 2004 number:23 21 16 ***************************************************************************************************************
More informationBourdon Tube Pressure Switches
DA /DS Bourdon Tube es Visible setpoint, adjustable deadband, snap action switch pressure ranges to 000 psi Weather-Proof Types DAW, DSW, DRW -/1 2-1/1 REAR MOUNTING FLANGE ().20 DIA. HOLES AT 120 ON -1/2
More informationAll Stainless Steel / SS Case Pressure Gauge
All Stainless Steel / SS Case Pressure Gauge 23L, 23B Series HAWK 23L and 23B series bourdon tube all stainless steel pressure gauges with front flange are designed to fulfill the requirements of high
More informationCC3060 TYPE 12 COMPACT CABINET COOLER AIR-TO-WATER FLUSH-MOUNT MODEL
CC3060 TYPE 12 CC3060 13 lbs 9,300 0.3 1 x 6 30 x 8-3/4 x 4 Efficiency: 68.8 Watts / C T based on average internal cabinet temperature. 2. CC3060 Rated cooling: 2,725 Watts mounted to an uninsulated 72
More informationMercy Hospital of Buffalo Catholic Health System 2 nd Floor Patient Holding Center 3 rd Floor Locker Rooms Shaflucas Architects, PC Project No.
SECTION 23 22 13 STEAM AND CONDENSATE PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION HVAC CONTROL SYSTEM PART 1 GENERAL 1.01 SUMMARY. A. Section Includes:
SECTION 15970 HVAC CONTROL SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Thermostats, temperature transmitters, controllers, automatic valves, dampers, damper operators, pneumatic/ electric
More informationPalmer Circular Chart Recorders
Palmer Circular Chart Recorders Pressure & Temperature Recorders Designed for indoor or outdoor use, our recorders provide long service life, even in harsh conditions. Internal Assemblies, Clocks and Parts
More information1. Wiring Diagrams: Power, signal, and control wiring.
Page 232123-1 SECTION 232123 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationF-2700 SERIES INSERTION VORTEX FLOW METER
F-2700 SERIES INSERTION VORTEX FLOW METER CALIBRATION Every ONICON flow meter is wet calibrated in a flow laboratory against standards that are directly traceable to N.I.S.T. A certificate of calibration
More informationSECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationTemperature Switch Gauges
Temperature Switch Gauges I MODEL DESCRIPTION MOUNTING TSG60B Bracket Mount (Standard) Surface TSG60K Back Flange Surface TSG60S Front Flange Panel TSG60X Explosion Proof (3 Switch Max.) Surface WINDOW
More informationIsoTherm FlowGuards Mini Ball Valves Gauges Aquastats Unions
82 IsoTherm FlowGuards Mini Ball Valves Gauges Aquastats Unions 83 Adjustment knob (sets supply temperature) Mixing Valve 1 Male BSP Threads Mixing Point Supply Inlet from Boiler Temperature Gauge (indicates
More informationWINTERS ( )
Economy Economy Test Panel Mounted Economy Spiral Tube Series New Sizes! Economy CRN Description The Winters Economy Gauge is designed for applications where cost savings are paramount. Many configurations
More informationB. Installation of instrumentation and control equipment including field transmitters, sensing elements, and miscellaneous devices.
ms1505 SECTION 40 91 00 - Page 1 PART 1 GENERAL 1.01 SECTION INCLUDES A. Instruments and control equipment. B. Installation of instrumentation and control equipment including field transmitters, sensing
More informationSOLFRUNT Pressure Gauges and Other Products for the Process Industries
A1 SOLFRUNT Pressure Gauges and Other Products for the Process Industries AMETEK s line of high quality process gauges are specifically designed to meet the demanding needs of the chemical and petroleum
More informationBimetal Thermowells Threaded
Bimetal Threaded Stepped Shank P P EXTERNAL THREAD [7] 2 1 / 2 only.75.75 [19] Lagging fl.50 Ø.50 [13] 1/2 P EXTERNAL THREAD P EXTERNAL THREAD [7] P P EXTERNAL THREAD THREAD.260 Ø.260 [7] [7].40.40 [10]
More informationPROCESS INSTRUMENTATION
INSTRUMENTS PROCESS INSTRUMENTATION Measuring your world since 1965 D C B A NOTE 1 NOTE 2 NOTE 3 NOTE 4 NOTE 5 4 4 3 REOTEMP Instrument Corporation 10656 Roselle Street San Diego, CA 92121 USA Phone: (858)
More informationFACILITY WATER DISTRIBUTION Revised 4/30/ Plumbing Systems
SECTION 22 11 00 - FACILITY WATER DISTRIBUTION PART 1 - GENERAL 1.1 SUMMARY A. This Section Includes: 1. Domestic water piping, within 5 feet of building. 2. Domestic water piping, above grade. 3. Pressure
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SUNY GENESEO 220523-1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSERIES 2000 TEMPERATURE REGULATOR SERIES 2000 TEMP. REGULATOR. SIZES 1/2" 2" CONTROLS -25 to 400 F
SERES 2000 TEMP. SERES 2000 TEMPERATURE APPLCATON DATA DRECT ACTNG Bottle Washing Machinery Steam Tables Plating Tanks Heating Ducts Fuel Oil Heaters Cooking Vats Water Heaters Heat Exchangers Parts Washer
More informationA. This Section includes general duty valves common to several HVAC piping systems.
SECTION 23 05 23 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION AIR TERMINAL UNITS
SECTION 23 36 00 AIR TERMINAL UNITS PART 1 - GENERAL 1.1 SUMMARY A. Section includes constant volume terminal units, variable volume terminal units, dual duct terminal units, fan powered terminal units,
More informationSECTION H3 TRAYMASTER SERIES DEAERATORS
SECTION H3 TRAYMASTER SERIES DEAERATORS SAMPLE SPECIFICATIONS PART 1 GENERAL... H3-12 1.1 Packaged Deaerator Specification... H3-12 PART 2 PRODUCTS... H3-12 2.1 Deaerator... H3-12 2.2 Deaerator Vessel...
More informationCIRCULATION HEATERS SPECIFICATIONS DESCRIPTION FEATURES CH & CHP SERIES HEAT EXCHANGE AND TRANSFER, INC. 6 to 480 kw and higher. Flanged construction
SPECIFICATIONS 6 to 480 kw and higher CIRCULATION HEATERS CH & CHP SERIES Flanged construction 208 volt through 575 volt, 3 phase 5 to 40 watts/in 2 and higher NEMA 4/12 Terminal housing DESCRIPTION Type
More informationA. This Section includes natural gas piping, specialties, and accessories within the building.
SECTION 226313 NATURAL GAS PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationDWS 41. Installation Data 44 Performance Specs DWS & DW-PRV Series
IRRIGATION Title Description Details Page Intro 3 2000 Series 4 Model 2000 Solenoid 1 3 12 Model 2000 Solenoid 4 8 15 Model 2030 Low Power Solenoid 1 3 17 Model 2030 Low Power Solenoid 4 8 19 Model 2160
More informationTemperature, Pressure Instruments
Plumbing Heating Cooling Temperature, Pressure Instruments www. GlobalTestSupply.com Throughout the 20th century, the Weiss name has been synonymous with quality and reliability in instrumentation. Some
More informationF-2700 SERIES INSERTION VORTEX FLOW METER
F-2700 SERIES INSERTION VORTEX FLOW METER APPLICATIONS Saturated steam Hot water to 500 F (260 C) standard 750 F (400 C) optional Applications with optional pressure sensor Superheated steam to 500 F (260
More informationSECTION VALVES
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. B. Related Sections:
More informationTENOCHCA HALL - PROJECT NO FAN COIL UNITS, RESTROOM AND FINISH RENOVATION
SECTION 220523.12 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brass ball valves. 2. Bronze ball valves. 1.2 ACTION SUBMITTALS A. Product Data: For each type of valve. 1. Certification that products
More informationGENERAL-SERVICE COMPRESSED-AIR PIPING SECTION GENERAL-SERVICE COMPRESSED-AIR PIPING PART 1 - GENERAL
13686.00 GENERAL-SERVICE COMPRESSED-AIR PIPING 221513-1 SECTION 22 1513 - GENERAL-SERVICE COMPRESSED-AIR PIPING 1.1 RELATED DOCUMENTS PART 1 - GENERAL A. Drawings and general provisions of the Contract,
More informationDIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION HVAC VALVES
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION 23 05 23 PART 1 GENERAL 1.01 DESCRIPTION A. Provide valves for the following systems: 1. Heating Hot Water 2. Chilled Water 3. Condenser
More informationTHERMOMETERS FOR TRANSFORMERS
THERMOMETERS FOR TRANSFORMERS GENERAL DESCRIPTION This instrument measures the insulating oil in the transformer. They are studied for withstanding to the most adverse process conditions due to the aggressiveness
More information910 Series Compact Control Valve
910 Series Compact Control Valve iaphragm ctuated CONTROL VLVES ctuator 7", 9", & 12" ctuator Sizes Heavy uty ie CastHousing 1/2" 6" Valve Sizes The Trerice 910 Series Pneumatic Control Valve offers high
More informationLiquid Strainers. Protect nozzles, valves and pumps from damaging debris. Experts in Spray Technology Spray Nozzles. Spray Fabrication.
Experts in Technology Nozzles Control Analysis Fabrication Liquid Strainers Protect nozzles, valves and pumps from damaging debris. Table of Contents T Strainers Low to Medium Pressure TW...3 TWC...3 TWF...4
More information2006 Product Range Overview. Belimo Project: One Bellevue Center, Seattle, Washington
2006 Product Range Overview Belimo Project: One Bellevue Center, Seattle, Washington Actuator Product Range Spring Return TF 18 in-lb [2 Nm] Approx. 4.5 sq. ft. LF 35 in-lb [4 Nm] Approx. 8 sq. ft. NF
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SECTION 22 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Valves, General 2. Gate Valves 3. Balancing Valves 4. Ball Valves 5. Swing Check Valves 6. Backflow Prevention Assemblies 7. Pressure
More informationfor biodiesel applications
Biofuels Pressure and Temperature Instrumentation for biodiesel applications WIKA Instrument Corporation manufactures products engineered with specific design features and gauge options optimized for utilization
More informationPressure Gage and Swichgage Instruments OPL Series 4-1/2 in. (114 mm) Diameter Dial
Pressure Gage and Swichgage Instruments OPL Series 4-1/2 in. (114 mm) Diameter Dial 96001 Revised 07-27-10 Section 05 R 1 2 Features Combination Indicating Gage and Critical Pressure Limit Switches High
More informationSeries Low Pressure Steam Heating Boiler Safety Valves
12-200 Series Low Pressure Steam Heating Boiler Safety Valves Section IV Heating Boilers Medium capacity safety valves protect ASME Section IV low pressure steam heating boilers. Cast bronze, full nozzle
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brass ball valves. 2. Iron swing check valves. 3. Iron gate valves. 4. Iron globe valves. B.
More informationAbout Gaugetech Warranty Trademarks Disclaimer
Product Catalog About Gaugetech Gaugetech is a leading manufacturer/distributor of pressure gauges, temperature instruments and related products serving the petrochemical, pulp and paper, hydraulic industries,
More informationTel-Tru Manufacturing Company World-Class Thermometers
Tel-Tru Manufacturing Company World-Class Thermometers We manufacture thermometers - but we sell service, reliability, product quality and performance. QUALITY AND PERFORMANCE FEATURES: CASE AND BEZEL
More informationDistributed By: M&M Control Service, Inc
Control Valves DESIGN & OPERATION Description A control valve is a device capable of modulating flow at varying degrees between minimal flow and full capacity in response to a signal from an external control
More informationTHE HISTORY OF WEKSLER GLASS THERMOMETER CORPORATION
THE HISTORY OF WEKSLER GLASS THERMOMETER CORPORATION Weksler Glass Thermometer Corporation has a long and proud history. Our founder, Harry Weksler, was an accomplished glass blower who left England in
More informationSpecialty Gauge Catalog Index
Specialty Gauge Catalog Index Specialty Gauge Introduction 3 Process Gauges - Series NF4UGY and LF4UGY 4 4 Series NF4UGY5 & LF4UGY5 and Dimensions 5 Standard Ranges 6 Ultra Pressure Gauges - Series UG-1
More information