SECTION METERS AND GAUGES FOR HVAC PIPING
|
|
- Fay McKinney
- 6 years ago
- Views:
Transcription
1 SECTION METERS AND GAUGES FOR HVAC PIPING PART 1 - GENERAL 1.1 SUMMARY A. Work included: Provision of materials, installation and testing of: 1. Thermometers 2. Thermometer Wells 3. Differential and Filter Pressure Gauges 4. Test Plugs 1.2 RELATED SECTIONS A. Contents of Division 23, HVAC and Division 01, General Requirements apply to this Section. 1.3 REFERENCES AND STANDARDS A. References and Standards as required by Section , HVAC Basic Requirements and Division 01, General Requirements. 1.4 SUBMITTALS A. Submittals as required by Section , HVAC Basic Requirements and Division 01, General Requirements. B. In addition, provide: 1. Maintenance Materials: a. Extra gauge Oil for Inclined Manometers: One Bottle b. Extra Pressure Gauges: Two 1.5 QUALITY ASSURANCE A. Quality assurance as required by Section , HVAC Basic Requirements and Division 01, General Requirements. 1.6 WARRANTY A. Warranty of materials and workmanship as required by Section , HVAC Basic Requirements and Division 01, General Requirements. October 29,
2 PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Thermometers: 1. Ashcroft 2. Trerice 3. Weiss 4. Marshaltown 5. Weksler 6. Or approved equivalent. B. Differential and Filter Pressure Gauges: 1. Dwyer 2. Or approved equivalent. 2.2 THERMOMETERS A. Thermometers - Adjustable Angle: Red-or blue-appearing organic liquid in glass: ASTM E 1; lens front tube, cast aluminum case with enamel finish, cast aluminum adjustable joint with positive locking device; adjustable 360 degrees in horizontal plane, 180 degrees in vertical plane. 1. Size: 9-inch scale. 2. Window: Acrylic. 3. Scale: Aluminum, white background, black graduations and markings. 4. Stem: 3/4-inch NPT brass (aluminum for installation in air ducts). 5. Accuracy: 2 percent, per ASTM E Calibration: with 2 Degrees F. graduations. 7. Basis of Design: Trerice BX THERMOMETER WELLS A. Description: Fitting with protective well for installation in threaded pipe fitting to hold test thermometer. 1. Material: Brass for use in copper piping. 2. Material: Stainless steel, for use in steel piping. 3. Extension Neck Length: Nominal thickness of 2-inches, but not less than thickness of insulation. Omit extension neck for wells for piping not insulated. 4. Insertion Length: To extend to center of pipe. 5. Cap: Threaded, with chain permanently fastened to socket. 6. Heat Transfer Fluid: Oil or graphite. October 29,
3 2.4 DIFFERENTIAL AND FILTER PRESSURE GAUGES A. Service: Air and non-combustible, compatible gases (Natural Gas option available.) B. Wetted Materials: Consult factory. C. Housing: Die cast aluminum case and bezel, with acrylic cover. Exterior finish is coated gray to withstand 168 hour salt spray corrosion test. D. Accuracy: Plus or minus 2 percent of full scale throughout range at 70 degrees F. E. Pressure Limits: Minus 20 Hg to 15 PSIG. F. Overpressure: Relief plug opens at approximately 25 PSIG standard gauges only. G. Temperature Limits: 20 to 140 degrees F. H. Size: 4-inch diameter dial face. I. Mounting Orientation: Diaphragm in vertical position. Consult factory for other position orientation. J. Process Connections: 1/8-inch female NPT duplicate high and low pressure taps, one pair side and one pair back. K. Standard Accessories: Two 1/8-inch NPT plugs for duplicate pressure taps, two 1/8-inch pipe thread to rubber tubing adapter and three flush mounting adapters with screws. 2.5 TEST PLUGS A. Description: Nickel-plated, brass-body test plug in NPS 1/2 (DN15) fitting. B. Body: Length as required to extend beyond insulation. C. Pressure Rating: 500 PSIG (3450 kpa) minimum. D. Core Inserts: One or two self-sealing valves, suitable for inserting 1/8-inch OD probe from dial-type thermometer or pressure gauge. E. Core Material for Air, Water, Oil and Gas: 20 to 200 degrees F (Minus 7 to plus 93 Degrees Celsius), chlorosulfonated polyethylene synthetic rubber. F. Test Plug Cap: Gasketed and threaded cap, with retention chain or strap. October 29,
4 G. Test Kit: Pressure gauge and adapter with probe, two bimetal dial thermometers, and carrying case. 1. Pressure Gauge and Thermometer Ranges: Approximately two times the system's operating conditions. PART 3 - EXECUTION 3.1 INSTALLATION A. Install thermometers in piping systems in sockets in short couplings. Enlarge pipes smaller than 2-1/2-inch for installation of thermometer sockets. Ensure sockets allow clearance from insulation. B. Where adequate space is not available, use turbine flow meters specifically designed for short pipe lengths. Use bi-directional turbine flow meters where indicated on piping diagrams. C. Install turbine and thermal energy meters in accordance with manufacturer's instructions, and as shown on drawings. Provide recommended upstream and downstream straight pipe length for accurate reading. D. Temperature Gauges: 1. Install in vertical upright position, tilted so as to be easily read at floor. 2. Thermometer Wells: Install in piping in vertical upright position. Fill well with oil or graphite, secure cup. E. Provide instruments with scale ranges selected according to service with largest appropriate scale. F. Install gauges and thermometers in locations where they are easily read from normal operating level. Install vertical to 45 degrees off vertical. G. Adjust gauges and thermometers to final angle, clean windows and lenses, and calibrate to zero. H. Locate test plugs adjacent to thermometers and thermometer sockets, adjacent to pressure gauges and pressure gauge taps, adjacent to control device sockets, or where indicated. I. Thermometer Range/Graduations: System Temperature (degree F) Graduations (degrees F) Chilled Water Heating Water October 29,
5 J. Pressure Gauge Range/Graduations: System Pressure (PSI) Graduations (PSI) Chilled Water Heating Water END OF SECTION October 29,
SECTION METERS AND GAUGES. 0.1 All meters and electronic gauges shall be able to communicate with the current BAS System (Johnson METASYS).
SECTION 15122 - METERS AND GAUGES PART 1 GENERAL 0.1 All meters and electronic gauges shall be able to communicate with the current BAS System (Johnson METASYS). 1.1 RELATED DOCUMENTS A. Drawings and general
More informationGuide Specification SECTION HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY
SECTION 23 21 16 - HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Air
More informationSECTION METERS AND GAGES FOR PLUMBING PIPING
PART 1 GENERAL 1.01 SECTION INCLUDES A. Positive displacement meters. B. Flow meters. SECTION 22 0519 METERS AND GAGES FOR C. Pressure gages and pressure gage taps. D. Thermometers and thermometer wells.
More informationSECTION METERS AND GAGES FOR HVAC PIPING
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. 1.2 SUMMARY A. This
More informationSECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY
SECTION 230533 - PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Static pressure
More informationSECTION METERS AND GAUGES
SECTION 22 05 19 PART 1 GENERAL 1.1 DESCRIPTION OF WORK: A. Extent of meters and gauges required by this section is indicated on drawings and/or specified in other Division-22 sections. B. Types of meters
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 230519 - METERS AND GAUGES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 ABBREVIATIONS A. Degree
More informationSAMPLE PRODUCT SPECIFICATIONS
SAMPLE PRODUCT SPECIFICATIONS Thermometers & Gauges Product Guide Specification THERMOMETERS & GAUGES Specifier Notes: This section covers Miljoco Corporation thermometers and pressure gauges suitable
More informationCSP PSYCHIATRIC SERVICES UNIT SECTION METERS AND GAUGES FOR HVAC PIPING
SECTION 23 05 19 METERS AND GAUGES FOR HVAC PIPING PART 1 GENERAL 1.1 SUMMARY A. Section includes 1. Digital Thermometers. 2. Pressure Gauges. 3. Test Plugs and Kits. 1.2 DEFINITIONS A. CR: Chlorosulfonated
More informationA. Provide all HVAC specialties required to complete the installation of all HVAC systems. B. Manufacturers: Refer to individual product item.
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION 23 05 02 PART 1 GENERAL 1.01 DESCRIPTION A. Provide all HVAC specialties required to complete the installation of all HVAC systems.
More informationSteam & Hot Water INSTRUMENTS. Adjustable Angle Industrial Thermometer. Econo Thermometer. ] Aluminum Stem. ] Air-Duct Stem
Adjustable Angle Industrial Thermometer Recognized globally as the Trerice BX Industrial Thermometer, this is an instrument of extreme accuracy and rugged dependability. Available in scale lengths of 7"(AX),
More informationSECTION GENERAL-DUTY VALVES FOR HVAC PIPING. A. Contents of Division 23, HVAC and Division 01, General Requirements apply to this Section.
SECTION 23 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Gate Valves 2. Balancing Valves 3. Ball Valves 4. Butterfly Valves 5. Swing Check Valves 1.2 RELATED SECTIONS A. Contents of Division
More informationGLASS INDUSTRIAL THERMOMETERS
TEL-TRU MANUFACTURING COMPANY GLASS INDUSTRIAL THERMOMETERS World -Class Thermometers Since 1916 www.teltru.com Glass Industrial Thermometers Tel-Tru Glass Industrial Thermometers are used on pipelines
More informationSECTION HVAC WATER PIPING ACCESSORIES
SECTION 23 05 10 PART 1 - GENERAL HVAC WATER PIPING ACCESSORIES 1.01 RELATED DOCUMENTS 1.02 SCOPE A. The requirements of the General Conditions, Supplementary Conditions, Division 1, Division 20, and Drawings
More informationSOLAR HEATING SYSTEM
SECTION 13600 SOLAR HEATING SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 07600 - Flashing and Sheet Metal. 2. 07900 - Joint Sealers. 3. 15260 - Thermal Insulation (Plumbing). 4. 15410 - Piping
More informationDARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
PART DESIGN DIRECTIVE. QUALITY ASSURANCE SECTION 530 METERS AND GAGES A. Comply with applicable UL standards pertaining to meters and gages and with applicable portions of ASME and Instrument Society of
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationDWYER INSTRUMENTS, INC. Phone: 219/ P.O. BOX 373 MICHIGAN CITY, IN 46361, U.S.A. Fax: 219/
Series 43000 Capsu-Photohelic Pressure Switch/Gage Specifications - Installation and Operating Instructions Bulletin B-34 Ø4-3/4 [120.65] 3-7/8 SQ [98.43] 3/4 CONDUIT 4-3/8 [111.13] HOUSING REMOVAL 3-1/16
More informationSECTION PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL
SECTION 22 10 10 PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and
More informationPalmer Circular Chart Recorders
Palmer Circular Chart Recorders Pressure & Temperature Recorders Designed for indoor or outdoor use, our recorders provide long service life, even in harsh conditions. Internal Assemblies, Clocks and Parts
More informationINTRODUCTION. Catalog 898 covers one of the broadest lines of remote reading thermometers available anywhere in the world.
INTRODUCTION Miljoco Corporation is an international manufacturer of indicating temperature and pressure instruments and was founded in 1979 by Howard M. Trerice. Presently, its headquarters are located
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brass ball valves. 2. Iron swing check valves. 3. Iron gate valves. 4. Iron globe valves. B.
More informationTBM. Bi-Metal Thermometer
Description & Features: A general purpose, versatile 1" (25mm) to 6" (150mm) dial, 304 stainless steel thermometer Bi-metallic sensing element for reliable readings Back, bottom or adjustable angle connection
More informationDivision 23 - HVAC Section Switzerland Beallsville K-12 GENERAL DUTY VALVES FOR HVAC PIPING
SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division
More informationCAPSU-PHOTOHELIC PRESSURE SWITCH/GAGE*
CAPSU-PHOTOHELIC PRESSURE SWITCH/GAGE* Specifications - Installation and Operating Instructions Bulletin B-34 Series 43000 CAPSU-Photohelic Switch/Gage The CAPSU-Photohelic Switch/Gage is a most versatile,
More informationPRODUCT IDENTIFICATION & COMPANY
TECHNICAL DATA SHEET PRODUCT NAME : FLOW METERS SECTION 1 PRODUCT IDENTIFICATION & COMPANY Product Name Flow Meters ( FLOWTECH & BLUE & WHITE) Supplier EZ Water Technology Address 1647 S, Main St. Suite
More informationADJUSTABLE ANGLE THERMOMETERS
ADJUSTABLE ANGLE THERMOMETERS Commercial grade units available with 9" aluminum or plastic cases, spirit fill, and 3½" or 6" stems. Unit can be adjusted for easy reading at any angle. SPECIFICATIONS Case:
More informationA. Valves and specialties including necessary accessories indicated on drawings and specified in this section.
SECTION 15081 - VALVES AND SPECIALTIES (HVAC) PART - 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationA. This Section includes the following domestic water piping specialties:
SECTION 221119 - DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following domestic water piping specialties: 1. Backflow preventers. 2. Water pressure-reducing
More informationSECTION COMPRESSED-AIR PIPING FOR LABORATORY FACILITIES
Page 226113-1 SECTION 226113 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationTable of Contents. Automatic Section A B V. Coil Piping Packages A B P P. Water Source Heat Pump Hose Kits A B H K
Table of Contents Automatic Section Automatic Balance Valves Installation Operation Maintenance Instructions / Warranty Technical Information How To Order Coil Piping Packages Package Types How To Order
More informationVALVES, FIRE HYDRANTS, AND APPURTENANCES
VALVES, FIRE HYDRANTS, AND APPURTENANCES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Butterfly Valves B. Gate Valves C. Tapping Valve Assemblies D. Fire Hydrant Assemblies E. Flushing Devices (Blowoffs)
More informationA. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems.
SECTION 220523 - PLUMBING VALVES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball valves. 2. Butterfly valves. 3. Swing check valves. 4. Spring loaded check valves. 5. Water pressure reducing
More informationPROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
More informationProduct Catalog. Our Products. DCI Dynamic Instruments Website: dcidynamic.com
1 Product Catalog Our Products We at Dynamic are proud to present out new technical catalogue detailing our extensive range of Pressure Gauges, Thermometers, diaphragm seal, transmitter and accessories.
More informationMarsh Instruments. STD Pocket Thermometer. Digital Pocket Thermometer. Specifications. Specifications. Gas Pressure Test Set. belgas.
Marsh Instruments STD Pocket Thermometer 1" Dial 304SS Hermetically Sealed Case 5" long stem Protective Case with SS Clip Digital Pocket Thermometer 3.5 Digital LCD display ABS Plastic Case 5" long stem
More informationMarsh Instruments. Marshalltown Value Series Gauge. Specifications. X-Mas Tree Gauge. Specifications. belgas.net 1
Marsh Instruments Marshalltown Value Series Gauge ASME Grade B Extra Savings with Quantity Pricing 4 Standard Mounting Options: LM, CB, Right & Left (1.5" Only) Marshalltown Value Series are the most economical,
More informationMichigan State University Construction Standards. GENERAL-DUTY VALVES FOR HVAC PIPING Page
Page 230523-1 Copyright 2005 by The American Institute of Architects (AIA) Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA Modified by MSU Physical Plant
More informationPNEUMATIC CONTROL SYSTEMS DESIGN AND CONSTRUCTION STANDARD PART 1 - GENERAL. A. Codes and Standards that are Standard at the University:
PART 1 - GENERAL 1.01 Purpose: A. This design guideline contained here in includes the requirements for pneumatic control systems at The University of Texas at Austin. It is the intent to provide the highest
More informationA. This Section includes general duty valves common to several HVAC piping systems.
SECTION 23 05 23 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION VALVES PART 1 -GENERAL
SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SUNY GENESEO 220523-1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationTHE HISTORY OF WEKSLER GLASS THERMOMETER CORPORATION
THE HISTORY OF WEKSLER GLASS THERMOMETER CORPORATION Weksler Glass Thermometer Corporation has a long and proud history. Our founder, Harry Weksler, was an accomplished glass blower who left England in
More information1 (25mm): Acrylic Others: Glass standard, hermetically sealed
Description & Features: A general purpose, versatile 1" (25mm) to 6" (150mm) dial, 304 stainless steel thermometer Bi-metallic sensing element for reliable readings Back, bottom or adjustable angle connection
More informationSECTION HVAC CONTROL SYSTEM PART 1 GENERAL 1.01 SUMMARY. A. Section Includes:
SECTION 15970 HVAC CONTROL SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Thermostats, temperature transmitters, controllers, automatic valves, dampers, damper operators, pneumatic/ electric
More information1.1 PURPOSE A. This section is intended to define the general installation and minimum product requirements for hydronic and steam valves.
Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product
More informationGAUGE ACCESSORIES SY-14B
GAUGE ACCESSORIES PSN 25NVBR SY-14B TC-14 LC-14 BV25 TABLE 1 - PRESSURE SNUBBERS HOUSING HOUSING NPT PSI RATING STYLE CODE MATERIAL CODE MATERIAL CODE NPT AT 70 F PSN B Brass 25 1/4" 1,500psi S 303 S.S.
More informationUPDATE LOG FOR TECHNICAL PROVISIONS DIVISION 4 Date Item(s) Changed Page # 10/1/13 TECHNICAL PROVISIONS DIVISION 4 VALVE SPECIFICATIONS
UPDATE LOG FOR TECHNICAL PROVISIONS DIVISION 4 Date Item(s) Changed Page # 10/1/13 TECHNICAL PROVISIONS DIVISION 4 VALVE SPECIFICATIONS Replace entire document dated 1/12 with the revised document dated
More informationSECTION HVAC AIR CLEANING DEVICES
SECTION 23 40 00 HVAC AIR CLEANING DEVICES PART 1 - GENERAL 1.1 SUMMARY A. Section includes activated carbon filters, automatic renewable media filters, disposable, extended area panel filters, disposable
More informationSECTION GENERAL-DUTY VALVES FOR HVAC. A. Section includes valves for building services piping.
SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PART 1 - GENERAL 1.1 SUMMARY A. Section includes valves for building services piping. 1.2 REFERENCES A. AGA Z21.22 (American Gas Association) - Relief Valves
More informationBrown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC&R VALVES
SECTION 23 05 23 HVAC&R VALVES PART 1 - GENERAL 1.1 SUMMARY: A. Section includes valves for building services piping. 1.2 GENERAL VALVE APPLICATION REQUIREMENTS: A. Provide valve handle extensions that
More informationSECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationY610A, Y611A, and Y612A Series Vacuum Service Equipment and Relief Valves
Y610A, Y611A, and Y612A Series Vacuum Service Equipment and Relief Valves July 2013 W1094_1 Figure 1. Type Y610A or Y610AP Vacuum Breaker Introduction The Y610A, Y611A, and Y612A Series devices (Figures
More informationSECTION VALVES
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. B. Related Sections:
More informationP200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
More informationTBM. Bi-Metal Thermometer
Description & Features: A general purpose, versatile 1 (25mm) to 6 (150mm) dial, 304 stainless steel thermometer Bi-metallic sensing element for reliable readings Back, bottom or adjustable angle connection
More informationDistributed By: M&M Control Service, Inc PRODUCT PRODUCT CODE RESOURCE DOCUMENTS PAGE #
PRODUCT PRODUCT CODE RESOURCE DOCUMENTS PAGE # Pneumatic Receiver-Controllers Single Input Receiver-Controller RC 195 155-119P25 C-3 Multiple Input Receiver-Controller RC 195 155-036P25 C-5 Pneumatic Transmitters
More informationPP1 Series Piping Packages for VG1000 Series Ball Valves
PP Series Piping Packages for VG000 Series Ball s Product Bulletin PP2xxxxx- Series, PP8xxxxx- Series Code No. LIT-20974 Issued August, 204 PP Series Piping Packages are designed to provide an easier way
More information***************************************************************************************************************
15515 VALVES, HANGERS, AND SPECIALTIES *************************************************************************************************************** SPECIFIER: CSI MasterFormat 2004 number:23 21 16 ***************************************************************************************************************
More informationPowers Controls Powertop Two-Way Valves Normally Open
Powers Controls Powertop Two-Way s Normally Open VP 658-5 Description The VP 658 normally open valves are pneumatically operated valves designed to control the flow of both water and steam. Features Stainless
More informationP200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
More informationMichigan State University Construction Standards. GENERAL-DUTY VALVES FOR PLUMBING PIPING Page
Page 220523-1 SECTION 220523 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information300/400/ /900 SERIES
Dial Indicating Thermometers Vapor Actuated Remote 300/400/600 700/900 SERIES Indicates media temperature using a temperature-actuated liquid in the sensing element and a highly accurate, high quality
More informationMercy Hospital of Buffalo Catholic Health System 2 nd Floor Patient Holding Center 3 rd Floor Locker Rooms Shaflucas Architects, PC Project No.
SECTION 23 22 13 STEAM AND CONDENSATE PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSeries 240 Type and Type Pneumatic Control Valves Type 3244 Three-way Valve
Series 240 Type 3244-1 and Type 3244-7 Pneumatic Control Valves Type 3244 Three-way Valve DIN and ANSI versions Application Mixing or diverting valve for process engineering and industrial applications
More informationA. This Section includes piping and related specialties for general-service compressed-air systems operating at 150 psig or less.
SECTION 221513 - COMPRESSED-AIR PIPING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes piping and related specialties for general-service compressed-air systems operating at 150 psig or less. 1.2
More informationT200 Pressure Regulator
T200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges T202 has internal relief valve for overpressure protection The T200 series pressure regulator is a manual, direct acting,
More informationANSI version. The valve closes when the differential pressure rises
Self-operated Regulators Series 42 Differential Pressure Regulator with Type 2424/Type 2428 Actuator and Type 2422 Valve Type 42-24 A Type 42-24 B Type 42-28 A Type 42-28 B ANSI version Application For
More informationV46 Series Pressure-Actuated Water-Regulating Valves
FANs 1, 11 Product/Technical Bulletin V46 Issue Date 9 V46 Series Pressure-Actuated Water-Regulating Valves The V46 pressure-actuated modulating valves come in two types of control action: direct acting
More informationFlare Valves 1/2 inch 2-Way and 3-Way
Valve and Actuator Manual 977 Valve Product Information Section Product Bulletin VTF Series Issue Date 0596 Flare Valves 1/2 inch 2-Way and 3-Way The 1/2 inch flared valve line is designed to accurately
More informationAbout Gaugetech Warranty Trademarks Disclaimer
Product Catalog About Gaugetech Gaugetech is a leading manufacturer/distributor of pressure gauges, temperature instruments and related products serving the petrochemical, pulp and paper, hydraulic industries,
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SECTION 22 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Valves, General 2. Gate Valves 3. Balancing Valves 4. Ball Valves 5. Swing Check Valves 6. Backflow Prevention Assemblies 7. Pressure
More information627 Series Pressure Reducing Regulators
627 Series Pressure Reducing Regulators Introduction The 627 Series direct-operated pressure reducing regulators (Figure 1) are for low and high pressure systems. These regulators can be used with natural
More informationStandard Specifications. Model. Indication precision. Clear cover. Brass Mass (kg) Bourdon tube. Model (Standard) Model G (2) G27-10-R1
Pressure Gauge for General Purpose Series G5/G27 G5 G27 G5-0-0 G27-0- Be sure to read the precautions on page 663 for selection and mounting. Dimensions Port size () precision ±5% F.S. (Full span) Case
More informationP200 Pressure Regulator
P200 Pressure Regulator Minimize Sudden Downstream Load Change Wide Pressure Ranges P202 has internal relief valve for overpressure protection The P200 series pressure regulator is a manual, direct acting,
More informationAccutubes. Accuracy True double averaging design +1% of rate accuracy +0.1% repeatability Tested and certified by independent flow labs
s Meriam s Flow Sensors are lab-tested and field-proven flow elements perfect for gas, liquid or steam service. With thousands in use worldwide, the continues to be the right choice when ease of installation,
More informationPressure Gauge Guide
ourtesy of Steven Engineering, Inc.-230 yan Way, South San Francisco, A 900-6370-Main Office: (650) 5-9200- Local Area: (00) 25-9200-www.stevenengineering.com Gauge for General Purpose With limit indicator
More informationSECTION GENERAL-SERVICE AIR COMPRESSOR PART 1 - GENERAL
13686.00 GENERAL SERVICE AIR COMPRESSOR 221519-1 SECTION 22 1519 - GENERAL-SERVICE AIR COMPRESSOR 1.1 RELATED DOCUMENTS PART 1 - GENERAL A. Drawings and general provisions of the Contract, including General
More informationC.W. COX COMPANY a product line of Perfecto Products, Inc
C.W. COX COMPANY a product line of Perfecto Products, Inc MANUFACTURERS OF PRECISION INSTRUMENTS FOR WATER FLOW MEASUREMENT HALL FLOWMETER The Hall Flowmeter is a modified pitot tube which averages the
More informationTel-Tru Manufacturing Company World-Class Thermometers
Tel-Tru Manufacturing Company World-Class Thermometers We manufacture thermometers - but we sell service, reliability, product quality and performance. QUALITY AND PERFORMANCE FEATURES: CASE AND BEZEL
More information2015 RIGHT CHOICE. RIGHT PRICE. RIGHT NOW. DWYER INSTRUMENTS, INC. DWYER INSTRUMENTS, INC. DWYER INSTRUMENTS, INC.
2015ofcobc_Layout 4 7/7/14 3:38 PM Page 1 CT-D-I Instrumentation leaders for over 80 years through innovation, service & quality www.dwyer-inst.com pressure air quality flow temperature level process control
More informationGeneral: Literature: Technical: Quotes:
Customer Service Fast, friendly customer service professionals are available to process and provide assistance with your order whether it is by phone, fax, e-mail or through our website. Technical Support
More informationcs200 series commercial / Industrial pressure reducing regulators
November 2013 cs200 series commercial / Industrial pressure reducing regulators P1188 Figure 1. Typical CS200 Series Pressure Reducing Regulator Features and Benefits Wide Range of Body Sizes and End Connections
More informationDifferential Pressure Sensors
1 920 1920P01 Differential Pressure Sensors for neutral and mildly corrosive liquids and gases QBE63-DP Differential pressure sensor, suitable for gases and liquids, for the measurement of positive and
More informationPRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve
More informationLEAD FREE * LFF113RFP Flood Protection Shut Down Valve
Technical Bulletin TB-ACV-LFF11RFP LEAD FREE * LFF11RFP Flood Protection Shut Down Valve Installed upstream of Reduced Zone Backflow Preventer. Normally Open Valve - Closes when continuous discharge from
More informationPRESSURE REDUCING VALVE
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve
More informationConfidence with the global standard in pressure relief devices
QUALITROL LPRD Large pressure relief devices Confidence with the global standard in pressure relief devices Robust design and materials provide reliable protection and long life Widest array of options
More informationPressure Independent Control Series
Pressure Independent Control Series Two-Way, Brass Valve Bodies, -Inch to 2-Inch, ANSI 250 to 1-1/4 Inch NC - to 1-1/4-Inch NO 1- to2-inch NO Description Features Application Product Numbers and Ordering
More informationPressure Instrument Testing Equipment
Pressure Instrument Testing Equipment BULLETIN TE-1 A Halliburton Company A Durable, Portable Primary Standard Model 1305D Deadweight Tester The Ashcroft 1305D Deadweight Tester is an affordable, portable
More informationD I V I S I O N O F M A R S H B E L L O F R A M
PH Regulator Large Capacity Working Media Include ir, Steam and Liquids ll Vents are Tapped The PH is a direct operating pressure reducing regulator with large capacity. Ideally suited for uses in oil
More informationM x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator
Installation Instructions Issue Date June 15, 2007 Supersedes November 15, 2002 M9000-53x Cast Iron Flanged Valve Linkage Kit for Mounting a Single M9000 Series Electric Actuator Installation Parts Included
More informationNC State University Design and Construction Guidelines Division 23 Energy Management
1.1 Purpose A. The following guidelines provide the methodology and requirements to assure that designs meet NC State standards for campus utility metering. 2.1 General Requirements A. Meters shall have
More informationKeystone knife gate valves Figure OS1700
Bi-directional zero leakage ASME Class 150 rated knife gate valve. Designed for the rigors of high pressure slurry and oil sands applications Features General application The OS1700 has many features to
More informationSPECIFICATIONS - DETAILED PROVISIONS Section Valve and Gate Operations CONTENTS
SPECIFICATIONS - DETAILED PROVISIONS Section 13446 - Valve and Gate Operations CONTENTS PART 1 - GENERAL... 1 1.01 SUMMARY... 1 1.02 REFERENCES... 1 1.03 SUBMITTALS... 1 1.04 QUALITY ASSURANCE... 1 1.05
More informationJHawk Instrument Inc. warrants the
Warranty Statement JHawk Instrument Inc. warrants the component parts and workmanship of its products under normal use and service for a period of one year from the date of the shipment. All obligations
More informationBimetal Thermowells Threaded
Bimetal Threaded Stepped Shank P P EXTERNAL THREAD [7] 2 1 / 2 only.75.75 [19] Lagging fl.50 Ø.50 [13] 1/2 P EXTERNAL THREAD P EXTERNAL THREAD [7] P P EXTERNAL THREAD THREAD.260 Ø.260 [7] [7].40.40 [10]
More informationTEMPERATURE REGULATORS W91/W94 Series
Self-Operated Temperature Regulators Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company Self-Operating Design Indicating
More informationVELAN TRUNNION-MOUNTED
VELAN TRUNNION-MOUNTED Velan s standard trunnion-mounted ball valves offer increased value by incorporating advanced design features. TRUNNION-MOUNTED BALL The ball is fixed and the seat rings are floating,
More informationPRESSURE GAUGES DIAL THERMOMETERS PRESSURE & TEMP. SWITCHES PRESSURE & TEMP. TRANSMITTERS PIPES, PIPE FITTINGS & FLANGES
WATER METERS VALVES & COCKS PRESSURE GAUGES DIAL THERMOMETERS PRESSURE & TEMP. SWITCHES PRESSURE & TEMP. TRANSMITTERS PIPES, PIPE FITTINGS & FLANGES FILTER, REGULATOR & LUBRICATORS W IKA V I INSTRUMENTS
More information