OVID Refresher Inspector Course. A Guide to the uniform inspection procedure OVID
|
|
- Elinor McGee
- 5 years ago
- Views:
Transcription
1 OVID Refresher Inspector Course A Guide to the uniform inspection procedure OVID Presentation F, New Edition 2013
2 Mooring system components The brake band The wire The joining shackle The synthetic tail What is the weakest link?
3 Mooring system components
4 Worn Anchor Cable.
5 Mooring system components
6 Mooring system components
7 Mooring system components
8 Mooring system components
9 Mooring Bitt
10 Poor Mooring Practise
11 Poor Mooring Practise
12 Poor Mooring Practise
13 What happens when it goes wrong!
14
15 Mooring system components
16 Towing Winch?
17 Hydraulic line windlass
18 Windlass brake lining worn
19 Worn rollers - spread mooring system
20 Fender shackle pin loosened
21 Mooring Equipment Issues Are mooring lines coiled neatly and free of tripping hazards? What is the condition of mooring winches? If hydraulically powered, are savealls fitted? On split drum winches, are the lines stowed correctly with less than 1 full layer on the tension drum? Dates of last brake testing stencilled to winches? Are winch brakes applied properly? Are brakes out of gear? Brake bands appear to have sufficient thickness? Are lines wound onto the bitts correctly?
22 Practical Inspecting. Engine Rooms, Steering Gears and Compressor Rooms (Seismic Vessels Only)
23 Engine Room Inspection It should take about an hour. Meet the C/Eng in the office advise scope of the inspection. Check available paper work & have a general discussion. Paper work should include. Engine room operators instructions & procedures A list of critical machinery as required by the ISM Code. Spare part inventory together with critical spare parts.
24 Engine Room Inspection Engine room log book. Bunker receipts as per IMO requirements plus MSDS (fuel oil & diesel oil). Sulphur content of the fuel (limits 3.5% & 1.0% North Sea); alongside EEC ports 0.1% Sulphur. Fuel & Lubricating Oil test programme. Sight the Planned Maintenance System. C/E to show you its use & features. Machinery details, forward planning, maintenance procedures & historical data; spare parts inventory. Ensure PMS is in place is fit for purpose?
25 Documentation Are duty cycles of watch keepers posted? Are C/Eng s standing orders posted & signed by officers? Is the Engineers UMS check list available & used? Is the engine room Log Book maintained? Is objective evidence available to support effective Planned Maintenance System? Machinery spare parts inventory maintained? Critical machinery & spare parts have been identified & minimum stock holding quantified.
26 Inspection route Enter E.R by whichever access is easiest. Test M.E. mist detector, high level bilge alarms, Oily Water Separator oil content monitor alarm and the main fire pump. Inspect the workshop, welding area & purifier room. Proceed to Steering flat & test Fire Pump (if in steering flat). Sight also Emergency Generator Room and sight the gas bottle store. CO2, foam storage & cargo valve hydraulic valve control system.
27 Engine room - General Are all Main & Auxiliary Machinery fully operational? No obligation to tell you. Are there machinery parts left lying around? Unmanned Machinery Space if fitted is it fully utilised & operational; if not why. UMS alarm test records & record of alarms during the UMS?
28 Engine room Main Engine Check that :- Clean no serious leaks (oil, fuel & water). Sight front & back of the engine blocks; under T/C. Turbo-chargers / Exhaust gas pipes well lagged. Expansion bellows (gas inlet & outlet piping not leaking). Fuel pumps and pipes plus trace heating lines. No free standing oil under the engines.
29 Engine room Main Auxiliary Engines Clean no serious leaks (oil, fuel & water). No free standing oil under the engines. Fly wheel crank shaft seal not leaking. Exhaust pipes well lagged & no exhaust leaks. Instrumentation fully operational (console & pyrometers). Carrying load steadily (not hunting).
30 Engine gearbox
31 Exhaust Lagging
32 Turbo charger lagging.
33 Engine room Oily Water Separator Have a general look at the unit. Broken paint coating, dirty feet on paint work. Hose pipes with flanges stored near the unit. Inspect the pipe work for stub pieces or modifications that will allow oily liquids to be pumped directly overboard. Operating instructions posted. Pipe work line diagram. Anti-pollution notices posted.
34 Engine room Oily Water Separator The unit proper & overboard discharge monitor are as stated in form B & are approved by regulatory authority. Overboard valve locked & usually there will be an authority to open notice posted. Oily Water Separator. (testing the unit... ) Test oily water alarm & three way valve. There should be a visual & audible alarm. Testing will normally include flushing the unit with water.
35 Engine room Oily Water Separator The alarm may be triggered by Introducing an object, usually a brush into the pot Adding a test fluid Electronically inducing an alarm. During the test locate the three way valve (air or electrically controlled) when the unit goes into alarm you will feel the valve close or feel a rush of air from the vent.
36 Poor examples
37 Situations that may be encountered... Oil soaked lagging on hot pipes. Fuel oil heaters & trace steam pipe lagging on Main & Auxiliary engines plus purifiers. Self closing valves operational & not wired open. Emergency bilge injection valve to be conspicuously marked & records of when it was last overhauled. Pipe leakages & temporary repairs plus cement boxes. Bilges free oil & debris; purifier flat clean & free of oil & sludge.
38 Engine room - Electrical Switchboards Found in the following locations. Engine Control Room or separate compartment. Inside the engine room Emergency Generator Room. Emergency Battery Room (24V system). Check that... They are protected from water spray? If not has a risk analysis been done?
39 Engine room - Electrical Switchboards Check that... There is an insulated rubber mat in front of the S/B?- Guidance notes advise 6 mm thick. Electric shock safety posters are posted? Comprehensive black out recovery instructions are posted together with a list of critical equipment to be restarted (auto start with delay times & manual machinery start should be listed). Auto synchronising equipment fully operational.
40 Engine room -Electrical Switchboards Earth testing Systems are fitted Three lights with a test button. Resistance meters (infinity to zero, which is a full earth). To test for an electrical Earth... Press test button & lights have an uneven brightness. Constant reading or press test button or selector switch.
41 Deck Insulation??
42 Machinery Space Lighting.
43 Steering Gear The oil reserve header tank full/enough to charge system; save-all round the steering gear is free of oil. The emergency steering change over procedure posted & has been tested in last 3 months? Gyro repeater fitted in the steering flat and is it reading the same as bridge. The single failure criteria operational (test it). The steering gear access door is unobstructed and kept closed if it is a emergency escape? (auto closing device). The handrails & gratings & or non slip surface provided? The rudder stock support bearing is greased & water tight.
44 Emergency Systems Emergency auxiliary engine. Check that... Fuel tank has 18 hrs level marked (160 kw=846l). Test remote fuel shut off valve. (below 500L not req.) There are TWO engine starting systems (test them). Generator starting batteries (vented or sealed). Concise starting instructions for both automatic and manual operation provided? The area is well illuminated? Is an effective safety mat in front of the switchboard? Is the general condition & appearance of the area satisfactory?
45 Starting batteries
46 Operational Tests Emergency generator (starts easily using both starting systems & produces running voltage). Emergency fire pump (produces at least 5 Kgs/cm2). Steering gear emergency controls Pump & oil level failure auto change over operational. Bridge to steering flat communications. Bilge high level alarm (audible & visual alarms). Oily water separator alarm (audible & visual alarms). Main engine crankcase oil mist detector.
47 Workshop Lathe
48 Double bottom sounding pipe
49 Double bottom sounding pipe
50 Plate Cooler
51 Cooler inlet
52 ER Housekeeping
53 No test cert or swl on lifting lug
54 Fuel oil heater and pump.
55 Cement box round a corroded pipe
56 Overboard Valve.
57
Ultrasonic Thickness Measurements Shipboard Manuals Condition Surveys Ship Studies
Page 1 of 8 Vessels Name: Place & Date of inspection: Pre-Purchase Survey Documentation / Bridge Completed Not Found Not Given Priority General Particulars Time Charter Description (if available on board)
More informationALPHA MARINE CONSULTING LTD. 26, SKOUZE STR PIRAEUS GREECE
ALPHA MARINE CONSULTING LTD. 26, SKOUZE STR. 185 36 PIRAEUS GREECE mail@alphamrn.com www.alphamrn.com AMC NEWS Sep. 2013/TECH/15 Launch of Joint CIC on propulsion and auxiliary machinery by Paris, Tokyo
More informationQuick guide. Pusnes TM deck machinery Hydraulic Winches
Quick guide Hydraulic Winches English 2 nd Edition 2010 Introduction The intention with this Quick Guide for TM deck machinery is to help prevent equipment damage caused by incorrect operation of the ships
More informationOPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE. Deck: Ship s Power Plants
Page 1 of 8 Compiled by Approved by Chief Examiner Syllabus Committee: 26 February 2013 OPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE Deck: Page 2 of 8 KNOWLEDGE, UNDERSTANDING
More informationMaintenance Checklist
Appendix B Maintenance Checklist (Published in Commercial Fisheries News, February 2015, reprinted with permission) By Fred Mattera, NESTCO Conduct your inspection and maintenance activities according
More informationCERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY - MARINE ENGINEER OFFICER
CERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY - MARINE ENGINEER OFFICER EXAMINATIONS ADMINISTERED BY THE SCOTTISH QUALIFICATIONS AUTHORITY ON BEHALF OF MARITIME AND COASTGUARD AGENCY CHIEF ENGINEER (UNLIMITED)
More informationPART 8 MACHINERY INSTALLATIONS
PART 8 MACHINERY INSTALLATIONS PART 8 MACHINERY INSTALLATIONS SECTION SUBJECT 8.1 General 8.2 Auxiliary engines 8.3 Stern gear 8.4 Propeller and nozzles 8.5 Rudders 8.6 Steering gear 8.7 Tables 8.7.1
More informationAMENDMENTS TO MARPOL ANNEX I AND CHANGES TO THE OIL RECORD BOOK PARTS I AND II
GUIDANCE NOTE 05/2010 AMENDMENTS TO MARPOL ANNEX I AND CHANGES TO THE OIL RECORD BOOK PARTS I AND II To: OWNERS, MANAGERS AND MASTERS OF CAYMAN ISLANDS SHIPS This Guidance Note was previously issued as
More informationBatch Plant Maintenance
Batch Plant Maintenance Batch Plant Maintenance Preventative Maintenance PM Schedules Mixer (Haarup) Skip Hoist Cement Systems Pneumatic Valve Panels Water Systems Aggregate Bins & Equip Dust Collectors
More informationMARPOL Annex I and Changes to the Oil Record Book Parts I and II.
MANX SHIPPING NOTICE MSN 036 Amended 04 Jan 2011 DEPARTMENT OF ECONOMIC DEVELOPMENT MARPOL Annex I and Changes to the Oil Record Book Parts I and II. The objective of this MSN is to clarify the changes
More informationTRUCKINGTRUTH.COM T T. Daniel B s Pre-Trip Inspection Checklist
TRUCKINGTRUTH.COM T T Daniel B s Pre-Trip Inspection Checklist 1 My pre-trip begins as I approach the vehicle. I am looking for leaks, leaning one way or the other (which may indicate a low tire or bad
More information1 Name any 5stationary parts and moving partsof a large 2-stroke diesel engine?
2 Marks question Bank for ME 802 General & Motor 1 Name any 5stationary parts and moving partsof a large 2-stroke diesel engine? 2 Why in certain engine the bottom half of crosshead bearing is of single
More informationFuel Oil Fill, Transfer, and Storage (CG-47): Components
Fuel Oil Fill, Transfer, and Storage (CG-47): Components Name of Component Function of Component 1 Stop valve, locked shut Isolates the defueling main from the rest of the system 2 Main fill valve Controls
More informationAs a safety precaution, remove keys from the ignition while working under or around the vehicle.
CAB AND CHASSIS As a safety precaution, remove keys from the ignition while working under or around the vehicle. 1. Approach Check the overall appearance of vehicle stance (not leaning). Check for signs
More informationCHAPTER II-1 C. Construction subdivision and stability, machinery and electrical installations
Only the Danish version is authentic Notice D II-1 C 1 October 2002 Technical regulation on the construction and equipment, etc. of passenger ships on domestic voyages CHAPTER II-1 C Construction subdivision
More informationINFORMATION BULLETIN No. 84
Bulletin No. 84 Revision No. 05 Issue Date 23 Oct 2017 Effective Date 01 Nov 2017 INFORMATION BULLETIN No. 84 Oil Record Books Guidance and Instructions for Bahamas Recognised Organisations, Bahamas Approved
More information9Pollution reduction. For more technical information. The Boat Safety Scheme Essential Guide
9Pollution reduction The Boat Safety Scheme Essential Guide For more technical information The requirements in this chapter have been informed by, and may refer to, the following technical references,
More informationReport No.: Name of Ship: Plans referred during Initial Survey:
Report on the Surveys Concerning International Oil Pollution Prevention Certificate Part 7 Survey of installation for discharges from cargo spaces Initial/ Annual/ Intermediate/ Renewal/ Change of Flag
More informationEXECUTIVE SUMMARY - TUGS ASD TUG 2810 DECEMBER 2015
EXECUTIVE SUMMARY - TUGS ASD TUG 2810 DECEMBER 2015 TUGS ASD TUG 2810 CHARACTERISTICS Main dimensions: Length over all 28.67 m Breadth over all 10.43 m Depth at side 4.60 m Draught aft 4.90 m Full displacement
More informationSYSTEM SAVER 318 AIR COMPRESSOR FOR MACK E-TECH AND ASET ENGINES MAINTENANCE MANUAL
SYSTEM SAVER 318 AIR COMPRESSOR FOR MACK E-TECH AND ASET ENGINES MAINTENANCE MANUAL NON-THROUGH DRIVE THROUGH DRIVE Service Notes About This Manual This manual provides service and repair procedures for
More informationIMPORTANT INSTRUCTIONS FOR OPERATION & MAINTENANCE OF
IMPORTANT INSTRUCTIONS FOR OPERATION & MAINTENANCE OF CONVEYORS EASIKIT 300 EASIKIT 450 EASIKIT 600, 900, 1200 & 1500 The manufacturer does not accept responsibility for any loss, damage to other equipment,
More informationMEPC.1/Circ.736/Rev.1 25 August 2011 GUIDANCE FOR THE RECORDING OF OPERATIONS IN THE OIL RECORD BOOK PART I MACHINERY SPACE OPERATIONS (ALL SHIPS)
E 4 ALBERT EMBANKMENT LONDON SE1 7SR Telephone: +44 (0)20 7735 7611 Fax: +44 (0)20 7587 3210 MEPC.1/Circ.736/Rev.1 25 August 2011 GUIDANCE FOR THE RECORDING OF OPERATIONS IN THE OIL RECORD BOOK PART I
More informationWORKSHOP MANUAL. 63,4 cm³ chainsaws
WORKSHOP MANUAL General failures analysis Suggested tools I. Emak tool kit II. Compression tester: to check thermal group III. Electronic tachometer: for 2 and 4 stroke engines, measurement range from
More information1) Scheduled maintenance checks
1) Scheduled maintenance checks Definition This section lists the periodic inspections which must be carried out after a specified periods of operation. Intervals Periodic inspections are those which must
More information2. Stern view of NORDAMERIKA lying moored at Taizhou Terminal. 1. Bow view of NORDAMERIKA lying moored at Taizhou Terminal.
1. Bow view of NORDAMERIKA lying moored at Taizhou Terminal. 2. Stern view of NORDAMERIKA lying moored at Taizhou Terminal. 3. External shell plating. 4. External shell plating partly scratched with paint
More informationWORKSHOP MANUAL. Chainsaw GS35 GS350 MT350 MT3500
WORKSHOP MANUAL Chainsaw GS35 GS350 MT350 MT3500 General failures analysis Suggested tools I. Emak tool kit II. Compression tester: to check thermal group III. Electronic tachometer: for 2 and 4 stroke
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications........................... 1B-1 Special Tools........................... 1B-2 Mercury/Quicksilver Lubricants
More informationSection 10 Chapter 17
Section 10 Chapter 17 24 Valve, 8.3 Liter Engine Air Intake System Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have no meaning to New
More informationIndustrial Injections Compound Turbo Installation For 6.7L Scorpion
Industrial Injections Compound Turbo Installation For 6.7L Scorpion Step 1: Whenever you are doing an installation the first thing you should do is unhook the batteries to avoid arcing. You will need an
More informationAlarms, remote indications and safeguards for main reciprocating I.C. engines installed in unattended machinery spaces
(1980) (Rev.1 1993) (Rev.2 1996) (Rev.3 1997) Rev.4 1999) (Rev.5 Aug 2008) (Rev.6 July 2013) (Rev.7 Mar 2016) s, remote indications and safeguards for main reciprocating I.C. engines installed in unattended
More informationTroubleshooting 3Z8 038 Rev B
Troubleshooting 3Z8 038 Rev B INSTRUCTIONS WARNING INJECTION HAZARD This form is only a quick reference for troubleshooting Graco sprayers. To reduce the risk of serious injury, including fluid injection,
More informationAIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST
AIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST BELT TYPE IMPORTANT PLEASE MAKE CERTAIN THAT THE PERSON WHO IS TO USE THIS EQUIPMENT CAREFULLY READS AND UNDERSTANDS THESE INSTRUCTIONS BEFORE STARTING
More informationIMPORTANT INFORMATION BEFORE USING YOUR 12V ELECTRIC WINCH
IMPORTANT INFORMATION BEFORE USING YOUR 12V ELECTRIC WINCH The responsibility for safe operation of this winch ultimately rests with the operator. Please read all operating instructions carefully before
More informationLow Speed Engine Room W-Xpert W-X72 Simulator
Low Speed Engine Room W-Xpert W-X72 Simulator W-Xpert W-X72 Engine Room Simulator is based on typical solutions and presently used in medium engine rooms such as Suezmax tankers, Capesize bulk carrier
More informationIC-20-G. Engineering Spec. View thousands of Crane Specifications on FreeCraneSpecs.com. Page 1 of 7 Date: June 2006
Engineering Spec IC-20-G Page 1 of 7 Replaces: Form BD104G Dated: May 2004 The IC-20-1G is a self-propelled industrial crane designed for in-plant lifting and material handling applications. It is powered
More informationDon Searles Check List For Dredging Equipment Surveys
Don Searles Check List For Dredging Equipment Surveys 1. General 1.1. Take pictures of everything important. Take pictures showing the side of the dredge 1.2. Inspect logs and maintenance records. Get
More informationOWNERS GUIDE 12V / 24V DC ELECTRIC WINCH. 12,000lb (6124kg) TWO SPEED VERY IMPORTANT
OWNERS GUIDE 12V / 24V DC ELECTRIC WINCH. 12,000lb (6124kg) TWO SPEED VERY IMPORTANT IT IS ESSENTIAL THAT YOU READ AND UNDERSTAND THIS GUIDE BEFORE INSTALLING AND OPERATING YOUR WINCH WINCHMAX UK WWW.WINCHMAX.CO.UK
More informationANNEX 23. RESOLUTION MEPC.187(59) Adopted on 17 July 2009
RESOLUTION MEPC.187(59) Adopted on 17 July 2009 AMENDMENTS TO THE ANNEX OF THE PROTOCOL OF 1978 RELATING TO THE INTERNATIONAL CONVENTION FOR THE PREVENTION OF POLLUTION FROM SHIPS, 1973 (Amendments to
More informationOregon Fuel Injection
Cummins PT Fuel Pump Diagnostic No Start, with no smoke 1. This could be caused by the fuel pump not turning or a seized gear pump. Remove the fuel supply hose and the fuel inlet fitting from the gear
More informationOwner smanual. Banks Ram-Air Intake System (235, 250, 305 and 325 HP) Dodge 5.9L Cummins (24-valve) ISB Pickup Trucks
Owner smanual with Installation Instructions Banks Ram-Air Intake System 2003-2007 (235, 250, 305 and 325 HP) Dodge 5.9L Cummins (24-valve) ISB Pickup Trucks THIS MANUAL IS FOR USE WITH KIT 42145 Gale
More information6. Document tasks performed during visit and report any observations to the appropriate
Chiller Annual Maintenance RFP Attachment B Services Required Tasking: Vibration Analysis 1. All work shall be performed in accordance with safety policies 2. Check with appropriate customer representative
More informationSafelift Overhead Runway Beams & Rolling Beam Cranes
Operation & Maintenance Instructions Instructions for Safe Use Safelift Overhead Runway Beams & Rolling Beam Cranes Certification Safelift overhead runway beams and rolling beam cranes are lifting appliances
More informationSEASONAL MAINTENANCE CHECKLISTS Johnson Controls
SPRING CHECK LIST ABSORPTION CHILLERS Check starter and control panel. Leak test. Check hand valve diaphragms and replace as required. Check operation of purge unit. Change oil in the purge pump. Lubricate
More informationM/V OCEAN SUPPLIER. Vestland Marine Sp. z o.o. Chwarznieńska str 87E, Gdynia, PL. ME 303 Anchor Handling Tug Supply Vessel (AHTS), DPS-1
ME 303 Anchor Handling Tug Supply Vessel (AHTS), DPS-1 Vestland Marine Sp. z o.o. Chwarznieńska str 87E, 81-602 Gdynia, PL Genera Anchor Handling Tug Supply Vessel; DPS-1 GENERAL SHIPS NAME CALL SIGN C6VL3
More informationRanger Tugs and Cutwater Boats Orientation Checklist
Ranger Tugs and Cutwater Boats Orientation Checklist Boat Model: Owner's name: Delivery Captain: Date: DAY 1 Main Cabin: Main cabin components and functions Raising & Lowering the dinette table and bed
More informationABS Guide for Certification of Lifting Appliances 2016: Focus on machinery
ABS Guide for Certification of Lifting Appliances 2016: Focus on machinery Cernusco sul Naviglio, Italy 19 May 2016 Marine & Offshore Meeting 2016 Guide for Certification of Lifting Appliances Lifting
More informationSERVICE MANUAL Gearbox - Allison AT545 - Gearbox Installation
Gearbox - Allison AT545 - Gearbox Installation Oil level dipstick Gearbox oil cooler Auxiliary oil filter Modulator Page 3.4 Gearbox - Allison AT545 Checking Oil Level The dipstick and filler are situated
More informationInstallation, operation and maintenance manual
Installation, operation and maintenance manual HCT1LX30 FULL RISE SCISSOR LIFT READ THIS ENTIRE MANUAL BEFORE INSTALLATION TO ENSURE CORRECT OPERATION AND A LONG SERVICE LIFE 2 Tiraines str. Riga, LV 1058
More informationINTAKE/EXHAUST SYSTEM 7 C TURBOCHARGER
INTAKE/EXHAUST SYSTEM 7 C TURBOCHARGER Table Of Contents Page Identification.................................. 7C-1 Torque Specifications.......................... 7C-1 Sealants.....................................
More informationTowing and Road Service Guide For The Lexus CT200h. Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746
Towing and Road Service Guide For The Lexus CT200h Quality and Education Services AAA Automotive 1000 AAA Drive Heathrow, FL 32746 January 4 th, 2011 1 Index General Vehicle Information Major Component
More informationSummary Report for Individual Task L-3048 Troubleshoot a Purifier Status: Approved
Report Date: 30 Apr 2012 Summary Report for Individual Task 551-88L-3048 Troubleshoot a Purifier Status: Approved DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited. DESTRUCTION
More informationINSPECTION AND MAINTENANCE CHECKLIST
INSPECTION AND MAINTENANCE CHECKLIST Lattice-Boom Crawler Cranes Models 111-21000 & MLC Series Does Not Apply to Small Crawler Models or Model 31000 This record applies to the following crane: Crane Model:
More informationTable Summary of Sprinkler System Inspection, Testing, and Maintenance. Reference. Inspection , ,
Table 5.1.1.2 Summary of Sprinkler System Inspection, Testing, and Maintenance Item Frequency Reference Inspection Gauges (dry, preaction, and deluge systems) Quarterly 5.2.4.2, 5.2.4.3, 5.2.4.4 Control
More informationInstallation Instructions
2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com
More informationBOSS 107 SEPARATOR SYSTEM INSTALLATION & APPLICATION MANUAL
Website: www.recoveredenergy.com Email: oilwatersales@recoveredenergy.com BOSS 107 SEPARATOR SYSTEM INSTALLATION & APPLICATION MANUAL BOSS 2.2T/107 BOSS 5T/107 BOSS 11T/107 BOSS 25T/107 BOSS 45T/107 Installation
More informationTitle: Identification: Revision: GUIDANCE FOR THE RECORDING OF OPERATIONS IN THE OIL RECORD BOOK, PART I
CROATIAN REGISTER OF SHIPPING CIRCULAR Title: Identification: Revision: GUIDANCE FOR THE RECORDING OF OPERATIONS IN THE OIL RECORD BOOK, PART I Key words: Oil record book QC-T-249 0 Prepared by: Reviewed
More informationCOME.UP DV-15. Instruction manual.
COME.UP DV-15 Instruction manual www.bigfoottrade.kz Automotive Winch Thank you for purchasing a Winch. This manual covers operation and maintenance of the winch. All information in this publication is
More informationSEA ROYAL. Dimensions Length Overall : 60 m. Registration. Breadth Moulded : 16 m. Depth Moulded : 6 m
Registration Year built/ Builder : 2009 / Fujian Crown Ocean Shipping Industry Co.Ltd, China Flag : Sierra Leone Dimensions Length Overall : 60 m Breadth Moulded : 16 m Depth Moulded : 6 m Class : RINA,
More informationAIR BRAKES THIS SECTION IS FOR DRIVERS WHO DRIVE VEHICLES WITH AIR BRAKES
Section 5 AIR BRAKES THIS SECTION IS FOR DRIVERS WHO DRIVE VEHICLES WITH AIR BRAKES AIR BRAKES/Section 5 SECTION 5: AIR BRAKES THIS SECTION COVERS Air Brake System Parts Dual Air Brake Systems Inspecting
More informationTo ensure proper installation, digital pictures with contact information to before startup.
Check List for Optimal Filter Performance? There should be no back-pressure on the flush line. A 1 valve should have a 2 waste line, and 2 valve should have a 3 waste line. Do not use rubber hosing or
More informationCHAPTER 22 SERVICING
CHAPTER 22 SERVICING Section Title 22-10 Main Rotor Gearbox......................................... 22.1 22-11 Cleaning Chip Detector..................................... 22.3 22-12 Cleaning Sight Gage.......................................
More informationST. VINCENT AND THE GRENADINES
ST. VINCENT AND THE GRENADINES MARITIME ADMINISTRATION CIRCULAR N POL 012 AMENDMENTS OF THE SUPPLEMENT (FORM A AND B) OF THE IOPP CERTIFICATE TO: SHIPOWNERS, SHIPS OPERATORS AND MANAGERS, MASTERS, RECOGNIZED
More informationMixer Discharge Door Adjustment on models; 30, 42, 54, 81, 108, 135 mixers.
Knowledge Base Article Type: Instructions Mixer Discharge Door Adjustment on models; 30, 42, 54, 81, 108, 135 mixers. Description: Instructions on How to set-up and adjust the discharge door on Columbia
More informationTHE REPUBLIC OF LIBERIA Bureau of Maritime Affairs
THE REPUBLIC OF LIBERIA Bureau of Maritime Affairs Office of Deputy Commissioner of Maritime Affairs 8619 Westwood Ctr. Dr. Suite 300 Vienna VA. USA 22182 Telephone: +1 703 790 3434 Fax: +1 703 790 5655
More informationKWSL2000RM ! CAUTION!! READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION AND OPERATION OF THIS PRODUCT. DO NOT RETURN THIS PRODUCT TO SELLER.
Assembly & Operating Instructions KWSL2000RM 2000 Lb. 12VDC Electric Winch! CAUTION!! READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION AND OPERATION OF THIS PRODUCT. DO NOT RETURN THIS PRODUCT TO SELLER.
More informationWeekly Checks. (Deckhands and Pilot) (Tools / Equipment / Housekeeping) Equipment: Power Tools 1. Start 2. Clean 3. Fuel 4.
Weekly Checks (Deckhands and Pilot) Monday (Tools / Equipment / Housekeeping) Equipment: Power Tools 1. Start 2. Clean 3. Fuel 4. Service Hand Tools: 1. Inventory Cord Reel 1. Test Dewatering Equipment
More informationDUST COLLECTOR (BOTTOM REMOVAL BAG & CAGE) INSTALLATION AND OPERATING INSTRUCTIONS
4080 SE International Way. Suite B110, Milwaukie, OR 97222 (503) 654-0867 Fax: (503) 654-4671 email: ftech@filtertechnologyltd.com www.filtertechnologyltd.com DUST COLLECTOR (BOTTOM REMOVAL BAG & CAGE)
More informationEXECUTIVE SUMMARY - TUGS ASD TUG 3213 APRIL 2017
EXECUTIVE SUMMARY - TUGS ASD TUG 3213 APRIL 2017 CHARACTERISTICS Main dimensions: Length over all 32.44 m Breadth over all 13.29 m Depth at side 5.50 m Draught aft 6.30 m Full displacement 950 ton Power
More informationDuring the watch a log is kept of the various parameters of the main and auxiliary equipment. This may be a manual operation provided automatically
ENGINE ROOM LOG 18 During the watch a log is kept of the various parameters of the main and auxiliary equipment. This may be a manual operation provided automatically on modern vessels by a data logger.
More informationRELEASING PRESSURE IN THE HYDRAULIC SYSTEM,
Testing And Adjusting Introduction NOTE: For Specifications with illustrations, make reference to SPECIFICATIONS for 225 EXCAVATOR HYDRAULIC SYSTEM, Form No. SENR7734. If the Specifications are not the
More informationCHAPTER 12 SERVICING. Section Title Page
CHAPTER 12 SERVICING Section Title Page 12-10 Main Rotor Gearbox.................................. 12.1 12-11 Servicing................................. 12.1 12-12 Filter Replacement...........................
More informationSection of 14. Ice and Rain Protection
Ice & Rain Protection 1 of 14 WINDSCREEN WIPERS General The aircraft is fitted with two windscreen wipers, one on each pilots side windscreen, which are controlled by a 3-position (FAST, SLOW and MANUAL)
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationTroubleshooting the Transmission Hydraulic System
Testing and Adjusting IT28F INTEGRATED TOOLCARRIER POWER TRAIN Testing And Adjusting Introduction Reference: For Specifications with illustrations, refer to SENR5974, IT28F Integrated Toolcarrier Power
More informationDryMax Stern Tube & Rudder Seal System
SHAFT SEALING SYSTEMS DryMax Stern Tube & Rudder Seal System E Environmentally Friendly E Water-Lubricated System E Eliminates Shaft Wear LLOYD S REGISTER TYPE APPROVED PRODUCT For propeller shafts & rudder
More informationCHILLER START UP PROCEDURE FORM DOC. N (DOC.N BELOW TO BE RETURN TO AERMEC)
CHILLER START UP PROCEDURE FORM DOC. N 061103 (DOC.N 071103 BELOW TO BE RETURN TO AERMEC) 1. Preliminary Operation WARNING: The following operation must be done without the power supply (unit with the
More informationBENNETT CNG DISPENSER MAINTENANCE SCHEDULE
BENNETT CNG DISPENSER MAINTENANCE SCHEDULE Serial #: DIN #: Company Name: CAUTION: Only trained personnel may work on dispensers. CAUTION: The emergency shut off valve if installed must be closed. CAUTION:
More informationSPEC. SHEET No. GR-600E /EU-01 DATE November, 2012 TADANO ROUGH TERRAIN CRANE MODEL : GR-600EX (Left-hand steering) G E NER A L DATA CRANE CAPA
DATE November, 212 TADANO ROUGH TERRAIN CRANE MODEL : GR-6EX (Left-hand steering) G E NER A L DATA CRANE CAPACITY 6, kg at 3. m BOOM 5-section, 11. m 43. m DIMENSION Overall length approx. 13,38 mm Overall
More informationTopaz Master. 85T BP M 5700 kw DP2 - AHTS. Vessel Specifications
Topaz Master 85T BP - 64.8 M 5700 kw DP2 - AHTS Vessel Specifications Diesel-electric propulsion Lower fuel consumption, reduced environmental footprint 50-man accommodation - MLC compliant 420m 2 of clear
More informationSHERPA 4x4 OWNER'S MANUAL
www.sherpa4x4.com.au info@sherpa4x4.com.au SHERPA 4x4 OWNER'S MANUAL Copyright (C) Sherpa 4x4 www.sherpa4x4.com.au info@sherpa4x4.com.au 1 PLEASE READ WARNING! Your winch has a duty cycle and cannot be
More informationInstruction Book DeLaval Barrier Teat Dip Spray Extension Kit
Instruction Book DeLaval Barrier Teat Dip Spray Extension Kit - 0910 - Safety precautions DeLaval Barrier Teat Spray Exstention Kit Safety precautions Read carefully before using the product! For best
More informationVectRA AVT 3000 BUILDING FOR THE FUTURE
BUILDING FOR THE FUTURE This specification describes a high-performance Voith Schneider Propeller (VSP) tug in tractor configuration, designed for maximum efficiency in the performance of both harbour
More informationReport of the investigation into the engine room fire onboard the MV. Laurentian at sea on 11 October M.V. Laurentian
Report of the investigation into the engine room fire onboard the MV. Laurentian at sea on 11 October 2001 M.V. Laurentian The Bahamas Maritime Authority investigates incidents at sea for the sole purpose
More informationRESTRICTED CLASS 6-MASTER/ENGINEER SPC 022B TRAINER S GUIDE
DIESEL ENGINEERING FOR PACIFIC ISLAND MARINERS RESTRICTED CLASS 6-MASTER/ENGINEER SPC 022B TRAINER S GUIDE SECRETARIAT OF THE PACIFIC COMMUNITY GOVERNMENT OF TAIWAN/ROC TABLE OF CONTENTS COURSE INFORMATION...
More informationCylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
More informationff## MINISTRY OF TRANSPORT AND COMMUNICATIONS DEPARTMENT OF MARINE ADMINISTRATION Directive ( )
MINISTRY OF TRANSPORT AND COMMUNICATIONS ff## DEPARTMENT OF MARINE ADMINISTRATION No-6/421, Corner of Merchant &Theinbyu Road, Botataung Township, Yangon, Myanmar E-mail: dgdma.mm@gmail.com; dma.myan@gmail.com
More informationFord 6.0L Powerstoke Regulated Fuel Return
Ford 6.0L Powerstoke Regulated Fuel Return ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationREAD AND SAVE THESE INSTRUCTIONS. Centrifugal Downblast Exhaust Fan Belt Driven for Roof & Wall Mounting
READ AND SAVE THESE INSTRUCTIONS INSTALLATION, OPERATING INSTRUCTIONS & PARTS MANUAL Centrifugal Downblast Exhaust Fan Belt Driven for Roof & Wall Mounting Electrical wiring and connections should be done
More informationTECHNICAL SPECIFICATION OF TUG
Type of Vessel: CP ASD Tug, with Ship Assist Anchor Handling Fi Fi tug with Escort capability. Oil Recovery Ship 1 Classification: ABS+A1, RINA: C E, Escort salvage Vessel, tug; Towing escort tug; Service,
More informationPlanned Preventative Maintenance Schedule. Chilled Water Systems PPM Schedule. Data Centre Solutions Expertly Engineered
Planned Preventative Maintenance Schedule Chilled Water Systems PPM Schedule Data Centre Solutions Expertly Engineered Planned and contracted maintenance services To ensure that data centre or building
More informationReplacing the Internal Oil Filter Elements for HS85 and OS 85 Screw Compressors
Maintenance Bulletin (MB-0038) Version 1, Sept 2015 Replacing the Internal Oil Filter Elements for HS85 and OS 85 Screw Compressors The internal oil filter elements are recommended to be changed on new
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications................................ 1B-1 Special Tools................................ 1B-2 Quicksilver Lubricant/Sealant..................
More informationCLASS STATUS REPORT WADI SAHAM FUJAIRAH PORT AUTHORITY. Report date: IMO number: DNV GL number: 28725
CLASS STATUS REPORT CURRENT STATUS FUJAIRAH PORT AUTHORITY Report date: 2017 01 09 IMO number: 9150391 DNV GL number: VESSEL INFORMATION DNV GL id. no. Operational status In operation IMO no. 9150391 Vessel
More informationMARPOL Annex 1 Get it right the first time, every time
MARPOL Annex 1 Get it right the first time, every time Preventing accidents resulting in pollution is important, but pollution caused by operational failure is a bigger risk. Fines as a result of MARPOL
More informationInspections of Aerial Equipment
I Inspections of Aerial Equipment Milton J. Luttrell, III Aspen Aerials, Inc. nspections of aerial equipment are a requirement as set forth by the American Nations Standards Institute (ANSI). Owners of
More information2016 Vehicle Inspection Manual (VIM) Amendments
2016 Vehicle Manual (VIM) Amendments Current Criteria Table of Contents Truck/Trailer and Bus Truck, Trailer and Bus Section 3A Air Brakes Item 16 - Drum Brake System Components (p. 222) Amendment Table
More informationBOILER FEED SYSTEM OPERATION AND MAINTENANCE MANUAL
BOILER FEED SYSTEM OPERATION AND MAINTENANCE MANUAL IMPORTANT These instructions are intended as a guide for the Installing Contractor and as a reference for the Operator, Owner and Serviceman. RETAIN
More informationDMS Fortune 57m BHP - Anchor Handling Tug Supply Vessel. Vessel Specifications
DMS Fortune 57m - 4750 BHP - Anchor Handling Tug Supply Vessel Vessel Specifications Vessel Specifications Registration Year built / builder 2004 / Guangdong Yuexin Ocean Engineering Co. Ltd., China Flag
More informationVS403 INSTRUCTIONS FOR: VACUUM AND PRESSURE TEST / BRAKE BLEEDING UNIT MODEL: SAFETY INSTRUCTIONS INTRODUCTION & CONTENTS. fig.1
INSTRUCTIONS FOR: VACUUM AND PRESSURE TEST / BRAKE BLEEDING UNIT MODEL: VS403 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
More informationCopeland Screw TM Compressors
Copeland Screw TM Compressors Mechanical Guidelines for SHL & SHM Models using ESC-201 Control System Contents: Start-Up Procedure Operating Specifications Maintenance Trouble Shooting Guidelines Start-up
More information