CORDLESS DRILL User Manual EN
|
|
- Charlotte Gibson
- 5 years ago
- Views:
Transcription
1 CORDLESS DRILL User Manual EN
2 B B2 B B4 1 B5 8 6 Lo Hi
3 B6 B7 7 7 b a 7 B Description of the tool 1 Selection Torque 2 Inverter Switch 3 ON/OFF 4 Battery 5 Pushlock Button 6 Selection for 1st or 2nd 7 Quick Change Mandrel 8 Battery Charger 9 LED 10 Integrated Magnetic holder 3
4 2 Intended use The tool is designed for screwing and unscrewing as well as for drilling in wood, metal, ceramic and plastic materials. This tool should not be used for purposes other than those described above. 3 Before use Before turning on the cordless drill, read the following notes: 1 Charge the battery with the charger provided with the tool. A fully discharged battery recharges in one hour. 2 Use only appropriate bits and tip screwdrivers. 3 When screwing and drilling into walls, check for power lines, gas or water hidden. 4 Use 4.1. Charging the battery (B2-B3) 1 Pull the battery (5) of its abse, resting on the bottom base. 2 Check if the power voltage on the rating plate corresponds to the voltage available. 3 Install the battery into the charger. The red LED indicates that the battery is charging. Once loaded, the red LED turns off and the green LED stays on continuously. The load is lasted 1 hour (approx.) in case of a fully discharged battery. 4 During charging, it is normal for the battery to warm slightly. If you can not charge the battery, check: > That the socket has voltage. > That the charger contacts are reliable. If you still can not load, please send to our post-sales service: > The charger > The battery It is necessary to recharge the battery in time in order to ensure good durability. This is absolutely necessary from the moment you notice that the power of the cordless drill decreases. Never discharge the battery completely. You can damage it! CAUTION: recharge the battery regularly, for example once every six months Setting the torque (B4) The drill is provided with a mechanical adjustment of torque. This can be adjusted to a size screw for its adjustment wheel. The torque depends on several factors: > The type and hardness of the material to be treated. > The type and length of the screws used. > Of the requirements to be met by bolted joints. If the torque is reached, a chirp indicates that the uncoupling has been done. Attention! Do not regulate the adjusting ring by the torque until the machine stops. 4
5 4.3. Drilling (B4) To drill, put the adjustment wheel for the torque in the last grade drill, in grade drill the safety clutch is deactivated. When drilling, the maximum torque is available Switch the direction of rotation (B5) The slide switch over the on/off switch allows to choose the rotation direction of the drill / driver with battery and prevent accidental starting. You can select clockwise rotation or leftward. To prevent damage to the gear, do not change the direction of rotation if the machine is running. In the case that the slide switch is in center position, switch on / off crashes Switch on / off (B5) The switch on / off allows you to adjust the speed continuously, depending on the intensity with which the switch is pressed Switching speed 1 to speed 2. Fig. 4 / Item 6 (B7) Note: Press the 6 gearshift lever only in the stability of the device. In the first gear (gear selector position 6 in 1) a speed of 400 min-1 and torque is achieved. This setting is suitable for all fastening applications. In the second gear (6 speed selector switch position: 2) a speed of about 1400 min-1 is achieved to carry out drilling operations Display battery status (B8) Three color LEDs indicate the status whenever the ON / OFF button (4) is pressed. > All LEDs are lighted: the battery is fully charged. > Yellow and red LEDs lighted: the battery has enough charge. > Red LED lighted: the battery is empty, you should charge it LED display (B8) The LED (10) light can illuminate the screwing and unscrewing area under unfavorable lighting conditions. The LED (10) light illuminates automatically, at the time the switch on / off (4) is pressed Tool change (B9) ATTENTION! For works (eg changing tools, maintenance, etc.) on the cordless screwdriver, put the switch in the direction of rotation (3) in middle position. > The cordless screwdriver is equipped with a quick coupling mandrel (9) with automatic lock on. > Unscrew the mandrel (9). The overture of the mandrel (a) must be large enough to house the connector (drill or screwdriver). > Select the appropriate tool. Put the connector as far as possible from the overture of the mandrel. > Adjust the mandrel and then check if the connector is well supported Screwing Use preferably automatic centering screws (eg Torx, Phillips head) to ensure complete safety work. Ensure that the shape and size of the screw are appropriate. Perform rotation torque control as described above: depending on the size of the screw. 5
6 5 Technical specifications Power Gear 1 Gear 2 12V Li-ion d.c./1,3ah Li-ion 0 to 400 U / min 0 to 1400 U / min Level rotation coupling Max. torque (soft / hard) Rotate to the left / right Coupling capacity mandrel Charge voltage, battery Charging current, battery Battery charger voltage Duration of load Noise and vibration L pa sound pressure level K pa Imprecision L WA Sound power level K wa imprecision 23Nm Yes 1-10mm 12.5 V D.C ma V~/ Hz 1 h Noise and vibration values have been determined according to EN db (A) 3 db (A) 72.8 db (A) 3 db (A) Use noise protection. Exposure to noise can lead to loss of hearing. Vibration total values (vector sum of three directions) have been determined according to EN Metal drill Vibration emission value a h m/s 2 Imprecision K 1,5 m/s 2 Pierced without percussion Vibration emission value a h <2,5 m/s 2 Imprecision K 1,5 m/s 2
7 6 Cleaning and maintenance Remove from the wall outlet before all cleaning works Cleaning > Keep protection devices, air vents and the motor housing as clean (dust free) as possible. Clean the appliance with a clean cloth or clean with compressed air at low pressure. > We recommend cleaning the appliance directly after each use. > Clean the device regularly with a damp cloth and a little soap. Do not use any cleaner or detergent; They can damage the plastic parts of the tool. Ensure that no water comes into the device Maintenance Recharge the battery regularly, for example once every six months. 7 Repairs Only use accessories and parts recommended by the manufacturer. If this is damaged, despite the quality control and care of the machine, repair the tool only in a specialized technical service. If the power tool is damaged, it must be repaired by the manufacturer or its representative or a qualified electrician to avoid any risk related to security. 8 Safety recommendations and warnings This device complies with the prescribed recommendations for safety devices. Read the instructions carefully before connecting the tool. Improper use can cause injury or damage. People who are not familiar with the operation of the device should not use it. Keep the manual in a safe place. Children and teenagers should not use the tool. 9 General safety recommendations General safety recommendations for the tool. WARNING: Read all safety warnings and all instructions. Not following the warnings and instructions may result in electric shock, fire and / or serious injury. Save all warnings and all instructions for future reference. The term tool in the warnings refers to your electrical power tool connected to the current (with cord) or batterypowered tool (without power cable) Workspace Security a) Keep the area clean and well lit up. Cluttered or dark areas can cause accidents. b) Do not use power tools in explosive environments, eg in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and people away during the use of the machine. Distractions can cause you to lose control of the tool. 7
8 9.2. Electrical safety a) It is necessary that the power tool plugs are adapted to the base. Never modify the plug in any way. Do not use adapters with earthed tools. Unmodified plugs and adapted bases reduce the risk of electric shock. b) Avoid body contact with earthed earth as pipes, radiators, stoves and refrigerators. There is an increased risk of electric shock if your body is in contact with grounded surfaces. c) Do not expose power tools to rain or wet conditions. The penetration of water into a tool increases the risk of electric shock. d) Do not misuse the cable. Do not use the cord for carrying, pulling or unplugging the tool. Keep the cord away from heat, oil, edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a tool outside, use an extension cord suitable for outdoor use. Using a cable suitable for outdoor use reduces the risk of electric shock. f) If it is necessary to use the tool in a location with moisture, use a secure supply with residual current device (RCD). The use of an RCD reduces the risk of electric shock Security staff a) Be aware of what you are doing and use common sense while using the tool. Do not use a tool when you are tired or under the influence of drugs, alcohol or medication. A moment of distraction in the use of a tool can cause serious personal injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust masks, non-slip safety shoes, helmets or acoustic protection used in appropriate conditions reduce injuries. c) Avoid accidental starting. Make sure that the switch is in the off position before plugging in to power or battery, collect or transport. Carrying tools with your finger on the switch or plugging the machine with the button in on position can cause accidents. d) Remove any adjusting key before turning the tool on. A key left attached to a rotating part of the tool may result in personal injury. e) Do not rush. Maintain proper footing and balance at all times. This allows better control of the tool in unexpected situations. f) Dress appropriately. Do not wear loose clothing or jewelry. Keep hair, clothing and gloves away from moving parts. Loose clothing, jewelry or long hair can get caught in moving parts. g) If devices for connecting equipment for extraction and dust collection are supplied, make sure they are connected and properly used. Use of dust collection can reduce risks due to dust Use and maintenance of the tool a) Do not force the tool. Use the right machine to the application being performed. A suitable tool will do the job better and more safely if used for the purpose for which it has been built. b) Do not use the tool if the switch does not allow to turn it on or off. Any machine that can not be controlled by the switch is dangerous and must be repaired. c) Disconnect the power source supply or battery block machine before changing accessories or before storing the machine. These preventive safety measures reduce the risk of accidental starting of the machine. d) Keep the tool off away from children and do not allow to be used by people who are not familiar with the machine. Tools are dangerous in the hands of inexperienced. e) Make sure the machine maintenance and moving parts are not aligned or blocked, that it has not broken parts or any other condition that may affect the operation of the tool. In case of damage, take the machine to a repair service before using it again. Many accidents are caused by poorly maintained machines. f) The machines used for cutting with sharp pieces that have had good maintenance are less likely to become blocked and are easier to control. 8
9 g) To use the machine, accessories and blades, etc. according to these instructions, taking into account the working conditions and the work to be done. The use of the machine for operations other than those provided can lead to dangerous situations Using machines with battery and precautions for use a) Do not use any other charger than the one specified by the manufacturer. A charger that fits to a type of battery can cause a risk of fire when used with other types of batteries. b) Do not use tools with batteries other than those specified. The use of any other type of battery may create a risk of injury and fire. c) If the batteries are not used, keep them away from other metal objects such as clips, coins, keys, nails, screws or other small objects that can lead to a connection from one terminal to another. Short-circuiting the terminals of a battery can cause burns or fire. d) In bad conditions, liquid may be ejected from the battery; avoid any contact. In case of accidental contact, flush with water. If the fluid comes into contact with eyes, seek medical assistance. The ejected battery fluid may cause irritation or burns Care and Maintenance a) Repairs must be performed by a qualified expert, using only identical replacement parts. This will ensure that the safety of the tool is maintained. 10 Special safety recommendations > Hold the tool by insulated gripping parts while performing an ongoing operation in which the cutting element or screw may contact hidden wiring. Contact with a wire under stress can put the metal parts of the power tool exposed under stress and cause an electric shock to the operator. > Use appropriate detectors in order to show the hidden supply ducts or consult local companies. Contact with electrical lines can cause a fire or electric shock. Damage to a gas line can cause an explosion. Drilling a water pipe can cause damage. > Stop the appliance immediately when the tool blocks up. Expect coupling reactions that can cause major consequences. The tool crashes if: The appliance is overloaded If you get stuck in the piece on which you are working > Hold tightly the portable electric tool. Because of the unscrewing or screwing, may have, high reaction instantly. > Fix the piece that is going to be worked on. A piece well-set or fixed in a vise piece is fixed more securely than held in hands. > Keep workspace clean. Mixtures of materials are particularly dangerous. Dust from light metals can be explosive or flammable. > Before putting off the portable electric tool, wait until it is completely stopped. There is a risk that the machine blocks up, which represents a loss of control over it. > Do not open the battery. Risk of short-circuit. Protect the battery from heat sources such as direct exposure to sun and heat. There is a risk of explosion. > Vapors can escape in case of damage and improper use of the battery. Ventilate the workplace and in case of discomfort, consult a doctor. Vapors may pose irritation in the airways. > If the battery is defective, liquid can go out and come into contact with nearby objects. Control the elements affected. Clean or change them, if necessary. 9
10 11 Explanation of symbols Respect all symbols in this manual and on your tool. Remember these symbols and these signs, you can work better and more safely with the tool if you know to correctly interpret the signs and symbols. Attention Read the user manual before using Wear protective eyewear Hearing protection Resistant gloves When working with materials that produce dust, always use respiratory protection. The devices used are materials, so they should not be deposited with household garbage! Please help by collaborating to protect resources and the environment and to deposit these products through relevant recycling services, if any. According to applicable essential safety standards of the European Regulations. 12 Environmental protection The devices used are materials, so they should not be deposited with household garbage! Please help by collaborating to protect resources and the environment and to deposit these products through relevant recycling services, if any. For questions on this matter, please contact your local council or a specialized site. 13 Certification The tests have been carried out in accordance with following standards: EN :2009/A11:2010 EN : 2010 EN :
11 Annotations 11
12 BOSSAUTO INNOVA, S.A. Polígono Industrial Valldoriolf c/ Thomas Edison, La Roca del Vallés. Barcelona. España tel.: / fax: / info@bossauto.com
4V LITHIUM-ION SCREWDRIVER OWNER S OPERATING MANUAL
CSD-4107BG 4V LITHIUM-ION SCREWDRIVER OWNER S OPERATING MANUAL Your screwdriver has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When
More informationRMT1201. ORIGINAL INSTRUCTIONS Cordless Multi-Tool
RMT1201 ORIGINAL INSTRUCTIONS Cordless Multi-Tool Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. Safety GENERAL
More informationeclipse Instruction Manual 4.0V Li-Ion Screwdriver Part #:
eclipse Instruction Manual 4.0V Li-Ion Screwdriver Part #: 902-588 Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com Test Equipment Depot - 800.517.8431-99
More informationSAFETY AND OPERATING MANUAL. Lithium-Ion cordless hammer drill WX372 WX372.1 WX372.9
SAFETY AND OPERATING MANUAL 2 Original Instructions General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
More informationInstruction Manual 4.0V Li-Ion Screwdriver. Part #: ECLIPSE ENTERPRISES, INC Chula Road, Amelia Court House, VA 23002, U.S.
Instruction Manual 4.0V Li-Ion Screwdriver Part #: 902-588 ECLIPSE ENTERPRISES, INC. 13302 Chula Road, Amelia Court House, VA 23002, U.S.A 2 3 Intended use Your ECLIPSE ENTERPRISES, INC. 902-588 screwdriver
More informationInstruction Manual. CORDLESS DRILL 18V Li-ion WITH IMPACT FUNCTION. Model SROM 1172
Instruction Manual CORDLESS DRILL 18V Li-ion WITH IMPACT FUNCTION Model SROM 1172 Our tool range has you covered for DIY. Whatever the job, make light work of it with MAKO tools. Product Features: 1. Keyless
More informationoriginal instructions 18V Torch RFP1801
original instructions 18V Torch RFP1801 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. Safety GENERAL POWER
More informationRPS1215 ORIGINAL INSTRUCTIONS. Cordless Pruner
RPS5 ORIGINAL INSTRUCTIONS Cordless Pruner Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.
More information18V CORDLESS DRILL DRIVER CDT16180
18V CORDLESS DRILL DRIVER CDT16180 LX400 SAFETY INSTRUCTIONS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or
More informationInstruction Manual CORDLESS DRILL & DRIVER 18V. Model SROM 1170
Instruction Manual CORDLESS DRILL & DRIVER 18V Model SROM 1170 Product Features: Dear Valued Customer, Thank you for purchasing this Samson Power Tool. We are dedicated to providing quality Samson Power
More informationSSW 18 LTX 600 SSW 18 LTX 400 BL
SSW 18 LTX 600 SSW 18 LTX 400 BL en Operating Instructions 5 fr Mode d'emploi 9 es Instrucciones de manejo 13 www.metabo.com SSW 18 LTX 400 BL 1 SSW 18 LTX 600 1 2 3 2 3 4 5 7 4 7 6 6 9 8 9 8 10 2 11.
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 7 6 2 5 4 2 3 A1 A2 1 2 A3 B A3 B C1 C2 3 C3 D 1. FORWARD/ REVERSE ROTATION CONTROL 2. SOFT GRIP HANDLE 3. BATTERY PACK RELEASE BUTTON 4. BATTERY PACK*
More informationSAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 2 3 4 9 8 5 6 7 A1 A2 1 2 1 3 2 A3 B1 3 2 1 B2 C1 2 3 1 C2 C3 C2 C3 D F E 1. KEYLESS CHUCK 2. TORQUE ADJUSTMENT RING 3. TWO-SPEED GEAR CONTROL 4. FORWARD/REVERSE
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 2 3 4 9 5 8 7 6 A2 A1 1 2 B1 A3 3 2 1 C1 B2 2 3 1 C2 C3 C2 C3 D E F G -- -- -- = 1. CHUCK 2. TORQUE ADJUSTMENT RING 3. TWO-SPEED GEAR CONTROL 4. FORWARD/REVERSE
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 1 2 3 4 8 9 5 7 6 A1 A2 1 2 1 3 2 A3 B1 A3 B1 3 2 1 B2 C1 2 3 1 C2 C3 D E1 1-18 D E1 E2 E3 F 1-18 6 1. CHUCK 2. TORQUE ADJUSTMENT RING 3. TWO-SPEED GEAR
More informationTOOLPRO 18V Li-Ion Brushless Impact wrench
TOOLPRO 18V Li-Ion Brushless Impact wrench Instruction Manual CIW180HB.9 After Sales Support FREE CALL 1300 889 028 EMAIL:salesau@positecgroup.com Important - Please read these instructions fully before
More informationWR 22SE WR 25SE WR25SE. Handling instructions
WR 22SE WR 25SE WR25SE Handling instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric
More informationSFC 18 A SFC 22 A English
SFC 18 A SFC 22 A English en 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a is a prerequisite for safe, trouble-free
More informationR18DDBL ORIGINAL INSTRUCTIONS. 18V Brushless Drill Driver
R18DDBL ORIGINAL INSTRUCTIONS 18V Brushless Drill Driver Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical
More informationTOOLPRO 18V 2 Speed Drill Driver
TOOLPRO 18V 2 Speed Drill Driver Instruction Manual CDT218G.1 After Sales Support FREE CALL 1300 889 028 EMAIL:salesau@positecgroup.com Important - Please read these instructions fully before operating
More informationCordless Rechargeable Saw Instructions for Use
Technical data Voltage: DC 10.8V Weight: 1.25Kg Stroke rate: 0-2100/min Stroke: 15mm Cutting capacity: max diameter in wood 80mm / in soft metal 7mm Charging time: Between 5.0-5.5 Hours Battery: 1.3Ah
More informationCordless Driver Drill
INSTRUCTION MANUAL Cordless Driver Drill MT064 MT065 003947 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model MT064 MT065 Steel 0 mm 3 mm Capacities Wood 25 mm 28 mm Wood
More informationPT-1441 Cordless Drill Driver 14.4V User s Manual
PT-1441 Cordless Drill Driver 14.4V User s Manual 1 st Edition, 2009 2009 Copy Right by Prokit s Industrial Co., Ltd. Please read this handbook carefully before using the tool General Safety Rules WARNING
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill 607D 637D 6337D 6347D 0089 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 607D 637D 6337D 6347D
More informationHDE 500-A22. English. Printed: Doc-Nr: PUB / / 000 / 03
HDE 500-A22 English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and
More information24V CORDLESS HAMMER DRILL
24V CORDLESS HAMMER DRILL CDI224MN ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
More informationSAFETY AND OPERATING MANUAL. Cordless Hedge Trimmer WG259E WG259E.5 WG259E.9
SAFETY AND OPERATING MANUAL 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire
More informationINSTRUCTION MANUAL. Cordless Angle Drill XAD01
INSTRUCTION MANUAL Cordless Angle Drill XAD0 0474 ENGLISH (Original instructions) SPECIFICATIONS Model XAD0 Capacities Steel 0 mm (3/8") Wood 25 mm (") No load speed (RPM) 0 -,800 /min Overall length 34
More information4-VOLT LITHIUM-ION AUTO-LOAD SCREWDRIVER w/led WORKLIGHT
SKU 241-1394 4-VOLT LITHIUM-ION AUTO-LOAD SCREWDRIVER w/led WORKLIGHT Operation Manual WARNING! Please read this manual before using this product. Failure to do so can result in serious injury. SAVE THIS
More informationCordless Driver Drill
INSTRUCTION MANUAL Cordless Driver Drill FD0 008796 ENGLISH (Original instructions) SPECIFICATIONS Model FD0 Steel 0 mm (3/8") Capacities Wood 2 mm (3/6") Wood screw 5. mm x 63 mm (7/32" X 2-/2") Machine
More informationSAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS
SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS LITHIUM-ION BRUSHLESS DRILL DRIVER LITHIUM-ION BRUSHLESS HAMMER DRILL WU175 WU175.1 WU309 1 2 3 4 10 5 9 8 6 7 12 11 100% A1 A2 0% 1 2 A3 A4 B1 B2 2 C1
More informationW6VB3 W8VB2. Handling instructions
Screw Driver Model W 6VM W 6V4 W 6VA4 W 6VB3 W 8VB2 Handling instructions W6VM W6V4 W6VA4 W6VB3 W8VB2 Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to
More informationWR 16SE. de fr it nl es pt sv da no fi el pl hu cs tr ro sl sk bg sr hr uk ru. Handling instructions
en WR 16SE de fr it nl es pt sv da no fi el pl hu cs tr ro sl sk bg sr hr uk ru Handling instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to
More informationOPERATOR'S MANUAL. Cat. No. C12 PC. To reduce the risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL Cat. No. C12 PC M12 Cordless Copper Tubing Cutter To reduce the risk of injury, user must read and understand operator's manual. General POWER TOOL SAFETY WARNINGS WARNING Read all safety
More informationRD V RECIPRO/PRUNING SAW
RD2865 RD2865 7 1 6 2 3 5 4 8 9 RD2865 1 A B C 2 7 1 2 D E F1 F2 COMPONT LIST 1 2 3 4 5 6 7 8 9 TOOL-FREE BLADE CLAMP LEVER LOCK-OFF BUTTON HANDLE BATTERY PACK * BATTERY PACK RELEASE LATCH ON/OFF SWITCH
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill 670D 680D 6390D R 0056 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model 670D 680D 6390D Steel
More informationC O R D L E S S I M PA C T D R I V E R W I T H 1 2 V LI- I O N B AT T E RY OWNER S MANUAL
C O R D L E S S I M PA C T D R I V E R W I T H 1 2 V LI- I O N B AT T E RY OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow
More information18V CORDLESS DRILL MODEL NO: CON18LiC
18V CORDLESS DRILL MODEL NO: CON18LiC PART NO: 6479531 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0817 - ISS 2 INTRODUCTION Thank you for purchasing this CLARKE Cordless Drill. Before
More informationPSR 960 PSR 1200 PSR 1440
2 609 140 210 - Buch Seite 1 Montag, 18. November 2002 8:07 08 Operating Instructions PSR 960 PSR 1200 PSR 1440 English 2 609 140 210 - Buch Seite 2 Montag, 18. November 2002 8:07 08 1 2 7 3 4 PSR 960
More information- Keep children and other people away while operating the rivet tool. Distractions can cause you to lose control of the tool.
PLEASE SPEND 5 MINUTES READING THESE INSTRUCTIONS BEFORE USING YOUR NEW BATTERY RIVET TOOL. TRUST US, IT WILL SAVE YOU TIME AND INCONVENIENCE IN THE LONG RUN. Please read the following safety information
More information1200W CaR PoliSheR en RS4900
1200W Car Polisher RS4900 RS4900 8 1 2 7 3 4 5 6 A B flat nozzle C D E F 1200W Car Polisher RS4900 G H flat nozzle I J K L 4 1200W Car Polisher COMPONT LIST 1 2 3 4 5 6 7 Variable speed control Switch
More informationSAFETY AND OPERATING MANUAL. Cordless rotary hammer WX382 WX382.1 WX382.2 WX382.3 WX382.4
SAFETY AND OPERATING MANUAL Original instructions 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
More informationCordless Line Trimmer
RLT6X RLT6B ORIGINAL INSTRUCTIONS Cordless Line Trimmer Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating this machine. Subject to technical
More informationSFC 14 A SFC 22 A English
SFC 14 A SFC 22 A English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling
More informationELECTRIC CAR POLISHER
ELECTRIC CAR POLISHER MODEL NO: CP254 PART NO: 6462108 OPERATION & MAINTENANCE INSTRUCTIONS LS0610 INTRODUCTION Thank you for purchasing this CLARKE electric car polisher. Before attempting to use this
More informationCordless Hedge Trimmer Taille-haies sans fil Cortasetos Inalámbrico EN F ES P05 P12 P20 WG255 WG255.1 WG255.9 WG275 WG275.9 WG280 WG280.
Taille-haies sans fil Cortasetos Inalámbrico F ES P05 P12 P20 WG255 WG255.1 WG255.9 WG275 WG275.9 WG280 WG280.9 2 5 3 6 4 7 1 8 9 A B1 1 2 1 3 B2 C C B2 1 2 D1 D2 D3 E 1. BATTERY PACK* 2. REAR HANDLE
More information3.6V SCREWDRIVER INSTRUCTION MANUAL CSD36F
3.6V SCREWDRIVER INSTRUCTION MANUAL CSD36F ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions
More informationCordless Impact Wrench
ENGLISH INSTRUCTION MANUAL Cordless Impact Wrench BTW0 00534 WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH SPECIFICATIONS Capacities
More information12V CORDLESS DRILL DRIVER. Model HY2150. User Manual
12V CORDLESS DRILL DRIVER Model HY2150 User Manual CONTENTS Section Description Page N o /N o s 1. OWNER S MANUAL & SAFETY INSTRUCTIONS 3 2. GENERAL SAFETY 3 5 3. BATTERY PACK 5 6 4. CHARGING 6 5. INSERTING/REMOVING
More informationCordless Driver Drill
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Driver Drill DF02D Read before use. SPECIFICATIONS Model: DF02D Drilling capacities Steel 5 mm Wood 6 mm Fastening capacities Wood screw ø3.8
More informationCordless Impact Driver
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Impact Driver TD0D Read before use. SPECIFICATIONS Model: TD0D Fastening capacities Machine screw 4 mm - 8 mm Standard bolt High tensile bolt
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill DDF343 DDF453 009075 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DDF343 DDF453 Steel 0 mm
More informationCordless Driver Drill
INSTRUCTION MANUAL Cordless Driver Drill XFD0 0360 ENGLISH (Original instructions) SPECIFICATIONS Model XFD0 Steel 3 mm (/") Capacities Wood 38 mm (-/") Wood screw 0 mm x 89 mm (3/8" X 3-/") Machine screw
More informationInstructions manual / Position Controller 1. GY-G Series INSTRUCTIONS MANUAL
Instructions manual / Position Controller 1 GY-G Series INSTRUCTIONS MANUAL Instructions manual / GY-G Series 2 IMPORTANT The tool delivered with this manual may been modified for specific needs. In that
More information18V CORDLESS COMBI DRILL MODEL NO: CON18NI
CON18NI.fm Page 1 Tuesday, August 21, 2012 11:53 AM 18V CORDLESS COMBI DRILL MODEL NO: CON18NI PART NO: 6485067 OPERATION & MAINTENANCE INSTRUCTIONS LS0812 CON18NI.fm Page 2 Tuesday, August 21, 2012 11:53
More informationEVO181B1. English
EVO181B1-TW EVO181B1-KR EVO181B1 English 4 10 16 A B 8 C EVO181B1-KR EVO181B1-TW D 2 E 13 8 9 EVO181B1-KR EVO181B1-TW F 3 ENGLISH (Original instructions) EVO181B1 MULTI TOOL Technical data Multi Tool Voltage
More informationCordless two speed drill/driver K 10613
Cordless two speed drill/driver K 10613 SAFETY AND PRECAUTION 1 Consider work area environment. Do not expose tools to rain. Do not use tools in damp or wet locations Keep work area clean and well lit.
More informationGeneral Tool Safety Warnings
Table of Contents General Tool Safety Warnings...2 Work Area...2 Electrical Safety...2 Personal Safety...2 Power Tool Use and Care...3 Battery Tool Use and Care...3 Additional Warnings Applicable for the
More informationOPERATOR'S MANUAL M12 FIR38, M12 FIR12 M12 FUEL RATCHETS WARNING. Cat. No.
OPERATOR'S MANUAL Cat. No. M12 FIR38, M12 FIR12 M12 FUEL RATCHETS WARNING To reduce the risk of injury, user must read and understand operator's manual. GENERAL POWER TOOL SAFETY WARNINGS WARNING Read
More informationCordless Impact Driver JCB-ID20LIBL
Safety and operating manual Cordless Impact Driver JCB-ID20LIBL ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
More informationCat. No. M18 Cordless multi-tool. To reduce The risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL Cat. No. M18 Cordless multi-tool To reduce The risk of injury, user must read and understand operator's manual. 2 General POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and
More informationELECTRIC ENGRAVER 15W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS WHAT S IN THE BOX. ozito.com.au. Electric Engraver
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
More informationIn-line Cordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL In-line Cordless Driver Drill DF00D 008706 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DF00D Steel 5 mm Capacities
More informationFMC641
3 8 4 7 2 1 6 5 www.stanley.eu FMC641 ENGLISH (Original instructions) 5 6 5 10 A 11 B 13 4 13 3 C1 C2 D 1 2 D 2 (Original instructions) ENGLISH Intended use Your Stanley Fat Max FMC641 impact wrench has
More informationSBC12 H Operating instructions Mode d emploi Manual de instrucciones
*254901* 254901 SBC12 H Operating instructions Mode d emploi Manual de instrucciones Safety Precautions Read all Instructions GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS WARNING! Read and understand
More informationCordless Impact Wrench
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Impact Wrench DTW50 DTW5 007450 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DTW50 DTW5 Capacities Standard
More informationCordless High Speed Drill
ENGLISH Cordless High Speed Drill MODEL 6503D 00039 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
More informationSIW 22T-A 1 / 2 " SIW 22T-A 3 / 4 "
SIW 22T-A 1 / 2 " SIW 22T-A 3 / 4 " English en 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a is a prerequisite for
More informationQUICK CONNECT SYSTEM 18V POWER UNIT & DRILL ATTACHMENT Australia BDCDMT180 New Zealand
QUICK CONNECT SYSTEM 18V POWER UNIT & DRILL ATTACHMENT www.blackanddecker.com.au BDCDMT180 Australia New Zealand 5 A B C D E 2 (Original instructions) ENGLISH Intended use Your Black & Decker MATRIX multi-purpose
More informationE-DRIV MD-Series DC Torque Control System Calibration Procedure
Revision: 1.1 July 05, 2017 E-DRIV MD-Series DC Torque Control System Calibration Procedure www.mountztorque.com 1080 N 11 th St - San Jose CA 95112-408.292.2214 1 GENERAL SAFETY RULES WARNING! Read and
More information20V Cordless Shrub Shear & Grass Shear P02 P10 P15 WG801 WG801.9
P02 P0 P5 WG80 WG80.9 2 WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth
More informationATD V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual
ATD 10525 12V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual KNOW YOUR PRODUCT (DRILL) 1. Keyless chuck 2. Torque adjustment collar 3. Speed selector 4. Forward/reverse selector 5. Battery
More informationCORDLESS TACKER MODEL NO: CCT48 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: LS0414
CORDLESS TACKER MODEL NO: CCT48 PART NO: 6485070 OPERATION & MAINTENANCE INSTRUCTIONS LS0414 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read
More information18V CORDLESS STAPLER/NAILER
18V CORDLESS STAPLER/NAILER MODEL NO: CONSN18LI PART NO: 6487055 OPERATION & MAINTENANCE INSTRUCTIONS LS1213 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product,
More informationBelt Sander JCB-BS950
Safety and operating manual Belt Sander JCB-BS950 ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions
More informationCordless Impact Wrench
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Impact Wrench DTW90 Read before use. SPECIFICATIONS Model: DTW90 Fastening capacities Standard bolt M8 - M6 Square drive High tensile bolt M8
More informationCordless Impact Driver
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Impact Driver DTD5 Read before use. SPECIFICATIONS Model: DTD5 Fastening capacities Machine screw 4 mm - 8 mm Standard bolt High tensile bolt
More informationWHAT S IN THE BOX METAL CUTTING SHEARS. Metal Cutting Shears 500W INSTRUCTION MANUAL SPECIFICATIONS. Hex Key. Max. Thickness: ozito.com.
WHAT S IN THE BOX METAL CUTTING SHEARS 500W INSTRUCTION MANUAL SPECIFICATIONS Motor: No load speed: Max. Thickness: Tool weight: 500W 0 1,600 rpm 1.2mm 2.2kg Metal Cutting Shears Hex Key ozito.com.au MCS-5000
More informationPower Paint Scraper 200W CPS-200. To view the full range visit: Instruction Manual 3 Year Replacement Warranty
Power Paint Scraper 200W Instruction Manual 3 Year Replacement Warranty CPS-200 WARNING! Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill 6095D 002032 WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
More informationFJC, Inc. Part # V BATTERY Charger/Maintainer INSTRUCTION MANUAL SAFETY WARNINGS AND PRECAUTION
FJC, Inc. Part # 52020 12V BATTERY Charger/Maintainer INPUT: 110V AC 60Hz OUTPUT: 6/12V DC 2A INSTRUCTION MANUAL SAFETY WARNINGS AND PRECAUTION CAUTION: TO PREVENT BATTERY DAMAGE: DO NOT USE on gel batteries
More informationENGLISH (Original instructions) INSTRUCTION MANUAL. Cordless Angle Drill DA330D DA331D. IMPORTANT: Read Before Using.
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Angle Drill DA330D DA33D 03258 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DA330D DA33D Capacities Steel
More information40 V HEDGE TRIMMER ATTACH YOUR RECEIPT HERE
ITEM #0796788 40 V HEDGE TRIMMER MODEL #KHT 240-07 Español p. 17 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer
More informationBENCH GRINDER MODEL NO. OZBG150WA
BENCH GRINDER 150mm MODEL NO. OZBG150WA OPERATING INSTRUCTIONS To view our entire range visit www.ozito.com.au SPECIFICATIONS MODEL NO. OZBG150WA Input Power: 150W Input Voltage: 230V ~ 50Hz No Load Speed:
More informationPower Carver 50W CPC-050. To view the full range visit: Instruction Manual 3 Year Replacement Warranty
Power Carver 50W Instruction Manual 3 Year Replacement Warranty CPC-050 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock,
More informationCordless Screwdriver
ENGLISH Cordless Screwdriver MODEL 6796D MODEL 6796FD MODEL 6797D MODEL 6797FD MODEL 6798D MODEL 6798FD 00260 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before
More informationCORDLESS BLOWER KIT INSTRUCTION MANUAL
WHAT S IN THE BOX Cordless Blower CORDLESS BLOWER KIT INSTRUCTION MANUAL 4.0Ah Battery & Fast Charger SPECIFICATIONS Voltage: 18V Battery: 4.0Ah Li-ion Charge Time: 80 min No Load Speed: 12,000/min Max.
More informationOPERATING INSTRUCTIONS. Note: 6V Charging. Requires Manual Shut Off.
Requires Manual Shut Off. 6 / 2 AMP,, DUAL RATE BATTER TTERY CHARGER 45005 OPERATING INSTRUCTIONS E224783 E224783 Note: 6V Charging Due to continuing improvements, actual product may differ slightly from
More informationECSS. Electric Chain Saw Chain Sharpener Assembly & Operating Instructions
ECSS Electric Chain Saw Chain Sharpener Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides
More informationENGLISH (Original instructions) INSTRUCTION MANUAL. Cordless Angle Drill DDA340 DDA350. IMPORTANT: Read Before Using.
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Angle Drill DDA340 DDA350 008950 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DDA340 DDA350 Capacities
More informationImpact Screwdriver. 8 Volt MAX. Operator s Manual. Model No
Operator s Manual 8 Volt MAX Impact Screwdriver Model No. 72.47720 CAUTION: Read, understand and follow all Safety Rules and Operating Instructions in this manual before using this product. Sears Brands
More informationGTC650L-XE Australia New Zealand
www.blackanddecker.com.au GTC650L-XE Australia New Zealand 2 11 D1 D2 D3 D4 3 ENGLISH (Original instructions) Intended use Your Black & Decker hedgetrimmer has been designed for trimming hedges, shrubs
More informationUSER S MANUAL CORDLESS GRASS & SHRUB SHEARS PSLHTM20
USER S MANUAL CORDLESS GRASS & SHRUB SHEARS PSLHTM20 CAUTION: Read all safety regulations and instructions. failures made in following the safety regulations and instructions may result in an electric
More informationScrewdriver. Cordless 3.6V. Operating Instructions XSD-360. XU1 Power tools
Cordless Operating Instructions XSD-360 Screwdriver 3.6V XU1 Power tools 1 23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 Website: www.xuone.com.au XSD-360 0816 SAFETY INSTRUCTIONS
More informationOWNER S TECHNICAL MANUAL
OWNER S TECHNICAL MANUAL 18V Cordless Grease Gun 450g 670AN3 Description These model guns are designed to dispense petroleum-based greases (up to NLGI 2) for general lubrication applications. A 36-inch
More informationCordless Impact Wrench
ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Impact Wrench DTW84 DTW85 Read before use. SPECIFICATIONS Model: DTW84 DTW85 Fastening Standard bolt M0 - M0 capacities High tensile bolt M0 -
More informationCordless Driver Drill
ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Driver Drill DF330D 009329 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DF330D Steel 0 mm Capacities Wood
More informationCORDLESS GLUE GUN. 7.2V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au GGL-7000 WHAT S IN THE BOX. Cordless Glue Gun.
WHAT S IN THE BOX CORDLESS GLUE GUN 7.2V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Input: 7.2V Glue Stick Diameter: 7.2mm Glue Stick Length: 190mm Heating Time: 15sec Working Time: 45min Battery Power:
More informationCORDLESS GRASS TRIMMER & SHEAR
WHAT S IN THE BOX Cordless Grass Trimmer / Shear CORDLESS GRASS TRIMMER & SHEAR Hedge Trimmer Blade Grass Shear Blade INSTRUCTION MANUAL SPECIFICATIONS Voltage: 18V No Load Speed: 1,200/min Hedge Trimmer:
More information2W COB + 1W LED Rechargeable Inspection Lamp Stock Nos Part Nos. CRIL/COB/BL CRIL/COB/OR CRIL/COB/GR CRIL/COB/YW
INSTRUCTIONS FOR 2W COB + 1W LED Rechargeable Inspection Lamp Stock Nos.82679 Part Nos. CRIL/COB/BL 82684 CRIL/COB/OR 82685 CRIL/COB/GR 82688 CRIL/COB/YW IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY
More information