Rotary Wing Decelerators for Miniature Atmospheric Entry Probes
|
|
- Charlene Page
- 5 years ago
- Views:
Transcription
1 20th AIAA Aerodynamic Decelerator Systems Technology Conference and Seminar<BR> 4-7 May 2009, Seattle, Washington AIAA Rotary Wing Decelerators for Miniature Atmospheric Entry Probes First Austin Howard 1 and Donald Elger, Ph.D.,P.E. 2 University of Idaho, Moscow, ID, Rotary wing decelerators were investigated as part of a miniature entry probe feasibility study. Previous technology demonstrations have shown that traditional low speed aerodynamic deceleration systems for this size class of probe can be relatively massive and risky. Rotary wing decelerators offer many potential advantages for miniature entry probes. The objectives of this project were to investigate the potential advantages of the rotary wing decelerator technology, assess aerodynamic modeling tools, and quantify performance of duel wing decelerator concepts using wind tunnel experimentation. Test models included a variety of two wing rotors with diameters of 152 mm or less in low speed air flows less than 20 m/s. The models with the lowest aspect ratio, 0.7 and 1.1, and highest solidity, 0.39 and 0.56, were observed to have the largest average thrust coefficients, 1.13 and 1.32 respectively. The tip speed ratio and the blade pitch were also identified as important parameters related to the magnitude of the Thrust Coefficient. Blade Element Momentum theory demonstrated the ability to predict average rotor thrust within 30% when compared with experimental observation for the majority of the cases considered. Nomenclature A b - Area of the blades A r - Area of the rotor disk C T - Thrust Coefficient c - Chord length D - Rotor diameter N - Number of rotor blades R - Radius of the rotor disk Re b - Reynolds number based on blade geometry Re t - Reynolds number based on rotor geometry s - Span length T Thrust force U - Free stream flow velocity - Angle of attack - Tip speed ratio (or TSR) - Angular velocity of the rotor (in radians per second) - Fluid density σ - Solidity γ - Kinematic viscosity I. Introduction INCE the 1960 s, NASA and other space agencies around the world have been sending instrumented S atmospheric entry probes throughout our solar system as part of an effort to understand planetary evolution and search for signs of life. Each destination in our solar system offers unique engineering challenges, requiring a unique set of design solutions. Parachutes, aeroshells and retro-rockets have been successfully applied as decelerator systems on atmospheric probes. As scientific instruments become smaller and require less power and designers develop new mission architectures to address the next generation of science questions; new technologies must be developed and old technologies adapted to meet the engineering demands of future missions. This project 1 Graduate Student, Mechanical Engineering Dept., AIAA Student Member 2 Professor, Mechanical Engineering Dept. 1 Copyright 2009 by the, Inc. All rights reserved.
2 considers the rotary wing decelerator as one of the potential enabling and/or enhancing technologies for future science architectures, including miniature atmospheric entry probes, lander networks, and precision targeted landers. For the purpose of this study, a rotary wing decelerator is defined as one or more rotating wings that retard the vertical velocity of the free falling payload. Unpowered rotary wing decelerators achieve steady rotation rates through a condition where net aerodynamic loads acting on a body result in a rotating state of equilibrium. Rotary wing decelerators have notable advantages when compared with parachute technology including lower sensitivity to lateral winds 1, mitigation of deployment problems 2, ability to execute soft landings 3, self scanning instrument platform 4, and higher falling velocities 4. A wind tunnel experiment was designed that could provide data on the feasibility of rotary wing decelerators for small probes, geometric influences on rotor performance and reference data for aerodynamic math model validation and development. II. Background Many studies and experiments have been conducted beginning in the 1960 s that investigate the feasibility and performance of rotary wing decelerators for vehicles ranging from the Apollo entry capsule to payloads less than 1kg in mass. NASA Researchers in the late 1960 s and early 1970 s researched a decelerator concept for entry vehicles that featured rotary wings that would perform as a decelerator during entry and later act as helicopter rotors close to the ground. This design could give astronauts the ability to maneuver and land the entry vehicle safely. Analysis and wind tunnel test were performed for subsonic, transonic and supersonic flow regimes 3. A research team, Nadal-Mora, Sanz-Andrés and Cuerva, is currently developing a rotary wing sounder for the purpose of measuring atmospheric properties around airports. Figure 1 shows a sketch of the rotary wing decelerator configuration as tested in vertical and horizontal wind tunnels. The unique feature in this design that makes modeling a challenge is the low aspect ratio of the wings, which is less than one. The wings are designed to wrap around the body and this requirement limits the wing dimensions. Body dimensions are limited by gyroscopic stability in rotation. Nadal-Mora, Sanz-Andrés and Cuerva developed a semi empirical aerodynamic model for their low aspect ratio, low Reynolds number rotor in autorotation 5, 6. The most effective blade pitch angles were found to be between 2 to 8 degrees. The team also developed a stability Figure 1. Rotary Wing Decelerator model for a rotary wing decelerator 7. Another research team, Bartz and Miklosovic, performed work to develop a decelerator technology capable of delivering supplies to troops on the ground in a variety of weather conditions and surface topologies. Six 247.7mm model helicopter blades were mounted to a rotating hub and placed in a horizontal wind tunnel. Pitch on the blades was adjusted as well as the angle of the trailing edge flaps. The flaps effectively added additional camber to the airfoil profile. This additional camber was shown to greatly impact the performance of the rotor. In one case the thrust performance was increased by 193% while in the same case the advance ratio was decreased by 67% (decrease in advance ratio corresponds to increase in rotational velocity). Bartz and Miklosovic reported thrust coefficients of up to 2.8 for wings with 2% camber. A relationship between thrust coefficient and rotational velocity was also noted; in the experiments, the higher the angular velocity of the rotor resulted in higher thrust coefficients 1. III. Experiment Design The experimentation for this research project was performed in the University of Idaho horizontal low speed wind tunnel. The models were mounted on a shaft with a bearing which allowed free rotation of the model. A force balance was used to measure lift and drag forces, an infrared tachometer was used to measure rotation rates and a hot film anemometer was used to measure air velocity. A stroboscope was also used as a redundant method to measure rotor velocity and to aid in flow visualization. See Figure 2 for a summary of the test setup. A control panel allowed the operator to control the velocity in the wind tunnel which induced rotation of the model attached to the force balance. The free stream velocity was gradually increased until the rotor began to spin. Velocity was increased by finite increments (1 or 0.5 m/s). Once 10 steps or a rotor rotation rate 6000 RPM was reached (whichever came first), the process was repeated in reverse until the rotor stopped spinning. Yaw angles 2
3 were fixed at 0 o for all experiments. A limited number of flow and model configurations were selected for photography and flow visualization. Figure 2. Experiment overview (looking from the side) A. Experiment Models A total of six dual wing rotor models were constructed for the wind tunnel experiment. The span-wise dimensions were limited by a test section blockage requirement of less than 0.10 and a preferred blockage ratio of 0.05 as suggested by Barlow, Rae, & Pope 8. However, the wings of model 2 did not meet this requirement with a test section blockage ratio of Each wing was constructed from mm thick, flat brass plates. a) b) c) d) Figure 3. Overview of wings 1, 2, 3 and 4 3
4 Wing 1 was considered the baseline design in its 10 o pitch configuration. It had an aspect ratio of 2 and was tested in blade pitch configurations of 5 o, 10 o, and 20 o. See Figure 3a). Wing 2 was designed to compare the effects of wing aspect ratio/solidity on thrust performance. The aspect ratio was set at 3 and the pitch was set at 10 o. See Figure 3b). Wing 3 was also designed to compare the effects of wing aspect ratio. The aspect ratio was set to 0.71 which is 5, 6, 7, 9 similar to the aspect ratio of the wings used in the research conducted by Mora et al. Wing 3 was tested in a 10 o pitch configuration. See Figure 3c). Wing 4 was designed to study the effect of a flexible trailing edge. A piece of paper was taped to the trailing edge of wing 1 which nearly doubled the chord length of the wing resulting in an aspect ratio of The rigid component of the wing was set to a pitch of 5 o during testing. See Figure 3d). 1. Performance Parameters During the wind tunnel experiment, velocity, drag force and rotor rotation rates were recorded. measurements were reduced to two representative dimensionless values: thrust coefficient and tip speed ratio. The thrust coefficient is defined by Eqn. (1). All (1) Note that the thrust force for this research has the opposite polarity when compared to propeller thrust force. The term thrust is used to describe the total drag of the rotor to avoid confusion with the drag of the rotor blades and to achieve consistency with standard mathematical modeling notation. The tip speed ratio is defined by Eqn.(2). (2) Another important parameter is the solidity, σ, of the rotor disk and is defined by Eqn. (3). (3) Reynolds number is another dimensionless constant that is commonly used to describe characteristic flow. For this experiment two Reynolds number definitions can be used. One defined by rotor s swept area and the other defined by the rotor blade geometry. All results in this paper are referenced to the wind tunnel test section velocity instead of Reynolds number because of the small range of Reynolds numbers observed. The range of Reynolds numbers tested, based on the swept area of the rotor was 2.36x10 4 to 1.37x10 5. The range of Reynolds numbers tested, based on the rotor blades, was 1.43x10 4 to 1.21x10 5. The Reynolds number based on the rotor geometry is defined by Eqn. (4) and the Reynolds number based on the rotor wing is defined by Eqn. (5). (4) (5) 2. Notation Each test configuration was assigned a designation that was used as a reference. For example w1p10 refers to wing 1 with a pitch of 10 o. Similarly w2p10 refers to wing 2 with a pitch of 10 o. 4
5 IV. Experiment Results 1. Thrust Data was collected primarily in the range of 5 to15 meters per second. A very wide range of thrust coefficients were observed ranging from 0.19 to The magnitude of the thrust coefficient of w1p20, w1p5, and w3p10 decreased with increasing velocity while the opposite behavior was observed for w2p10. The thrust coefficient of w4p5 was observed to be relatively constant throughout the velocity ranges tested. Wing 4 with a pitch of 5 o showed the highest average thrust coefficient of See Figure 4 for a comparison of thrust coefficients. The two wings with the highest average thrust coefficient, w4p5 and w3p10, also had the largest chord lengths. The high values of chord length resulted in the highest solidity and lowest rotor aspect ratios of the samples considered. Due to apparatus design, the test fixture was only capable of two wing geometries and therefore solidity and aspect ratio were varied together. Figure 4. Summary of rotor thrust coefficient versus free stream velocity The lowest thrust was produced by w1p20 which had the lowest average thrust coefficient of 0.34 and minimum thrust coefficient of See Table 1 for a comparison of mean, min and max thrust coefficients for all configurations. Table 1. Ranking of thrust performance Description Average Thrust Max Thrust Min Thrust Coefficient Coefficient Coefficient w4p w3p w1p w2p w1p w1p
6 2. Tip Speed Ratio Another performance parameter of interest is the tip speed ratio. It is a ratio of the tangential and normal velocity components at the tip of a rotor blade. The tip speed ratio can be used to determine the angle of incidence of the flow. The angle of attack and local airfoil lift and drag can be estimated by using knowledge of the rotor geometry and the local blade pitch. High values of tip speed ratio indicate a lower angle of incidence and contribute to a lower angle of attack. The tip speed ratio is defined by Eqn. (6). (6) Wing 2 with a pitch of 10 o had the highest average tip speed ratio of 5.42, and maximum tip speed ratio of The lowest value of tip speed ratio was encountered by w3p10 with an average value of The tip speed ratio versus wind tunnel velocity is plotted in Figure 5. See Table 2 for a comparison of recorded tip speed ratios for all configurations. Upon comparison of measured tip speed ratios to the thrust performance summarized in the previous section, no global trends were observed. A plot of thrust coefficient versus tip speed ratio is shown in Figure 6. Description Figure 5. Summary of rotor tip speed ratio versus wind tunnel velocity Table 2 Ranking of average tip speed ratio performance Average Tip Speed Ratio Max Tip Speed Ratio Min Tip Speed Ratio w2p w1p w4p w1p w1p w3p
7 Figure 6. Thrust coefficient vs. tip speed ratio 3. Summary of Results Table 3 summarizes the geometric, thrust and speed parameters. The two configurations with the highest solidity (w3p10 and w4p5) also had the lowest aspect ratio and the largest thrust coefficients. Description Chord (m) Table 3. Summary of geometry, thrust coefficient and tip speed ratio Span (m) Dia (m) Solidity Aspect Ratio Ave. Ang. of Attack ( ) Ave. Thrust Coefficient Ave. RPM Ave. Tip Speed Ratio w1p w1p w1p w2p w3p w4p
8 4. Flow Visualization Flow visualization was performed during the testing of three configurations: w1p20, w2p10, and w3p10. The objective of the flow visualization effort is to observe flow separation and span-wise flow in the boundary layer of the rotor blades. Thread streamers were taped to the top and bottom of the rotary wings with thin pieces of transparent tape. A stroboscope and a flash camera were used to capture the behavior of the threads in the boundary layer of the wing. a) b) c) Figure 7. w1p RPM, w2p RPM, w3p RPM Wing 2 with a pitch of 10 o was observed to have the most uniform flow pattern over the entire wing. Six threads were distributed evenly over the chord and span of the wing. Each thread oriented itself at nearly the same angle with the flow. See Figure 7. Wing 1 with a pitch of 20 o was observed to have a different flow pattern. The threads taped to the leading edge were observed to orient themselves almost parallel to the radial direction of the wing. This suggests that the centrifugal forces are dominant and that flow separation may be occurring in this region. The threads taped to the trailing edge of the wing show similar behavior to that of the threads on wing 2. See Figure 7. The third configuration, w3p10, had similar behavior on the leading edge of the wing. Along the middle of the chord of the wing, the flow behaved similar to the trailing edge of w1p20. The threads on the trailing edge of w3p10 were almost completely aligned with the chord-wise direction. See Figure 7. V. Comparison of Experimental Data with Predictive Math Models Two classic rotor aerodynamic modeling techniques were applied and compared to the experimental results in order to understand the applicability of the modeling techniques for the rotor geometries and flow regimes considered. The two techniques applied were Blade Element Theory (BET) and Blade Element Momentum Theory (BEM). Both theories are described in several text books 10, 11, 12. A custom Matlab script was developed for the BET model. For the BEM model, a previously developed wind turbine performance code was applied. The BEM software used was WT_Perf v3.10 which was developed by the National Renewable Energy Laboratory under the U.S Department of Energy. The software is available on the web at the address: last accessed July The airfoil 8
9 aerodynamics used in the performance predictions were documented by Rosen and Seter 13, who researched low speed airfoil aerodynamics as part of a study of Samara wing aerodynamics. For many of the wind tunnel configurations analyzed, the BEM model produced less than 20% average error. The cases where the BEM failed to produce predictions with lower error than measurement uncertainty were the cases with the lowest thrust coefficients. The custom BET code did not produce representative predictions for most of the rotor models considered. Table 4 includes a summary of model error and measurement uncertainty for all the test configurations. Each of the aerodynamic models listed in Table 4 used 100 rotor segments in the simulation. Ave. Thrust Coeff. Table 4. Summary of analysis Measur. Uncertainty Ave. % BEM % Error (WT_Perf ) Ave.% Max% BET % Error Ave.% Max% w1p w1p w1p w2p w3p w4p VI. Conclusion A. Influence of Geometric Features on Rotor Thrust The following list represents a summary of the observed effects that the geometric features of the various configurations had on the rotor performance. The following observations are referenced to the baseline configuration, w1p10 (except for no. 4 below which was referenced to w1p5). 1. Both increasing and decreasing pitch from the nominal value of 10 o for wing 1 reduced the thrust coefficient and the tip speed ratio. a. Increasing the blade pitch to 20 o reduced the thrust coefficient from 0.87 to 0.34 and the tip speed ratio from 4.06 to b. Reducing the blade pitch to 5 o reduced the thrust coefficient from 0.87 to 0.76 and the tip speed ratio from 4.06 to Increasing aspect ratio/reducing solidity reduced the magnitude of the thrust coefficient. 3. Decreasing aspect ratio/increasing solidity increased the magnitude of the thrust coefficient and reduced the magnitude of the tip speed ratio. 4. Adding flexible flaps to the trailing edge of w1p5 (referred to as w4p5) increased the average thrust coefficient from 0.76 to 1.32 and increased the average tip speed ratio from 1.80 to B. Assessment of Rotary Wing Modeling Techniques Two modeling techniques were investigated and applied: Blade Element Theory, and Blade Element Momentum Theory. Out of the modeling techniques BEM provided the most accurate predictions. Most models using BEM predicted thrust performance with less than 30% error with exception of w1p20 which produced predictions with 39% error. It was observed that BET does not produce accurate performance predictions for the rotor configurations tested. 9
10 Acknowledgments A special thanks to Tony Colaprete (NASA Ames Research Center) who provided the opportunity for this research project and who inspired this study, and to the Idaho Space Grant Consortium for their consistent support, advice, and connections to the people and resources need to complete this study. References 1 Bartz, J., & Miklosovic, D. S., An Experimental Analysis of Camber Effects of a 6-Bladed Flapped Autorotational Aerodynamic Decelerator, 17th AIAA Aerodynamic Decelerator Systems Technology Confrence. Monterey, CA Karlsen, L., Borgstrom, D., & Paulsson, L., Aerodynamics of a Rotating Body Descending From the Separation Position of an Artillery Munition Shell, 11th AIAA Aerodynamic Decelerator Systems Technology Conference Levin, A. D., & Smith, R. C. An Analytical Investigation of the Aerodynamic and Performance Characteristics of an Unpowered Rotor Entry Vehicle, NASA TN-D4537, Crimi, P. Analysis of Samara Wing Decelerator Steady State Characteristics, Journal of Aircraft, Vol. 25, Pg , Nadal-Mora, V., Sanz-Andrés, Á., & Cuerva, Á., Experimental Investigation of an Autorotating-Wing Aerodynamic Decelerator System, 18th AIAA Aerodynamic Decelerator Systems Technology Conference and Seminar, Nadal-Mora, V., Sanz-Andrés, Á., & Cuerva, Á., Model of the Aerodynamic Behavior of a Pararotor, AIAA Journal of Aircraft, Vol. 43, Pg , Nadal-Mora, V., & Sanz-Andres, A., Stability Analysis of a Free-Falling Pararotor, AIAA Journal of Aircraft, Vol. 43 No. 4, Pg , Barlow, J., Rae, W., & Pope, A., Low-Speed Wind Tunnel Testing. Wiley, Mora, V. N., Aerodynamic behavior of Atmospheric Soundings in Airport Surroundings, Doctoral Thesis. Madrid, Spain: Polytechnical University of Madrid, Johnson, W. Helicopter Theory, Princeton University Press, Stepniewski, W. Z., & Keys, C., Rotary Wing Aerodynamics, Dover, Burton, T., Sharpe, D., Jenkins, N., & Bossanyi, E., Wind Energy Handbook. Wiley., Rosen, A., & Seter, D., Vertical Autorotation of a Single-Winged Samara, Transactions of the ASME, Vol. 58, Pg ,
EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE
Chapter-5 EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE 5.1 Introduction The development of modern airfoil, for their use in wind turbines was initiated in the year 1980. The requirements
More informationPreface. Acknowledgments. List of Tables. Nomenclature: organizations. Nomenclature: acronyms. Nomenclature: main symbols. Nomenclature: Greek symbols
Contents Preface Acknowledgments List of Tables Nomenclature: organizations Nomenclature: acronyms Nomenclature: main symbols Nomenclature: Greek symbols Nomenclature: subscripts/superscripts Supplements
More informationDesign and Test of Transonic Compressor Rotor with Tandem Cascade
Proceedings of the International Gas Turbine Congress 2003 Tokyo November 2-7, 2003 IGTC2003Tokyo TS-108 Design and Test of Transonic Compressor Rotor with Tandem Cascade Yusuke SAKAI, Akinori MATSUOKA,
More informationGuide Vanes for Darrieus Water Turbine in Tidal Current
International Conference on Renewable Energies and Power Quality (ICREPQ 13) Bilbao (Spain), 20 th to 22 th March, 2013 Renewable Energy and Power Quality Journal (RE&PQJ) ISSN 2172-038 X, No.11, March
More informationDeployment and Drop Test for Inflatable Aeroshell for Atmospheric Entry Capsule with using Large Scientific Balloon
, Germany Deployment and Drop Test for Inflatable Aeroshell for Atmospheric Entry Capsule with using Large Scientific Balloon Kazuhiko Yamada, Takashi Abe (JAXA/ISAS) Kojiro Suzuki, Naohiko Honma, Yasunori
More informationNacelle Chine Installation Based on Wind-Tunnel Test Using Efficient Global Optimization
Trans. Japan Soc. Aero. Space Sci. Vol. 51, No. 173, pp. 146 150, 2008 Nacelle Chine Installation Based on Wind-Tunnel Test Using Efficient Global Optimization By Masahiro KANAZAKI, 1Þ Yuzuru YOKOKAWA,
More informationDeployment and Flight Test of Inflatable Membrane Aeroshell using Large Scientific Balloon
1 Deployment and Flight Test of Inflatable Membrane Aeroshell using Large Scientific Balloon Kazuhiko Yamada, Takashi Abe (JAXA/ISAS) Kojiro Suzuki, Naohiko Honma, Yasunori Nagata, Masashi Koyama (The
More informationCONCEPTUAL DESIGN OF ECOLOGICAL AIRCRAFT FOR COMMUTER AIR TRANSPORTATION
26 TH INTERNATIONAL CONGRESS OF THE AERONAUTICAL SCIENCES CONCEPTUAL DESIGN OF ECOLOGICAL AIRCRAFT FOR COMMUTER AIR TRANSPORTATION Yasuhiro TANI, Tomoe YAYAMA, Jun-Ichiro HASHIMOTO and Shigeru ASO Department
More informationHow Do Helicopters Fly? An Introduction to Rotor Aeromechanics
Audience: Grades 9-10 Module duration: 75 minutes How Do Helicopters Fly? An Introduction to Rotor Aeromechanics Instructor Guide Concepts: Airfoil lift, angle of attack, rotary wing aerodynamics, hover
More informationPropeller blade shapes
31 1 Propeller blade shapes and Propeller Tutorials 2 Typical Propeller Blade Shape 3 M Flight M. No. Transonic Propeller Airfoil 4 Modern 8-bladed propeller with transonic airfoils near the tip and swept
More informationReduction of Self Induced Vibration in Rotary Stirling Cycle Coolers
Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers U. Bin-Nun FLIR Systems Inc. Boston, MA 01862 ABSTRACT Cryocooler self induced vibration is a major consideration in the design of IR
More informationSTRUCTURAL DESIGN AND ANALYSIS OF ELLIPTIC CYCLOCOPTER ROTOR BLADES
16 TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS STRUCTURAL DESIGN AND ANALYSIS OF ELLIPTIC CYCLOCOPTER ROTOR BLADES In Seong Hwang 1, Seung Yong Min 1, Choong Hee Lee 1, Yun Han Lee 1 and Seung Jo
More informationPrimary control surface design for BWB aircraft
Primary control surface design for BWB aircraft 4 th Symposium on Collaboration in Aircraft Design 2014 Dr. ir. Mark Voskuijl, ir. Stephen M. Waters, ir. Crispijn Huijts Challenge Multiple redundant control
More informationADVENT. Aim : To Develop advanced numerical tools and apply them to optimisation problems in engineering. L. F. Gonzalez. University of Sydney
ADVENT ADVanced EvolutioN Team University of Sydney L. F. Gonzalez E. J. Whitney K. Srinivas Aim : To Develop advanced numerical tools and apply them to optimisation problems in engineering. 1 2 Outline
More informationStudy on Flow Fields in Variable Area Nozzles for Radial Turbines
Vol. 4 No. 2 August 27 Study on Fields in Variable Area Nozzles for Radial Turbines TAMAKI Hideaki : Doctor of Engineering, P. E. Jp, Manager, Turbo Machinery Department, Product Development Center, Corporate
More informationTransmission Error in Screw Compressor Rotors
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2008 Transmission Error in Screw Compressor Rotors Jack Sauls Trane Follow this and additional
More informationAn approach for cost and configuration optimization of horizontal axis wind turbine (HAWT)
International Conference on Renewable Energies and Power Quality (ICREPQ 14) Cordoba (Spain), 8 th to 10 th April, 2014 Renewable Energy and Power Quality Journal (RE&PQJ) ISSN 2172-038 X, No.12, April
More informationCFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate
CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate Sandeep M, U Sathishkumar Abstract In this paper, a study of different cross section bundle arrangements
More informationHypersonic Wind Tunnel Test of Flare-type Membrane Aeroshell for Atmospheric Entry Capsule
Hypersonic Wind Tunnel Test of Flare-type Membrane Aeroshell for Atmospheric Entry Capsule Kazuhiko Yamada (JAXA) Masashi Koyama (The University of Tokyo) Yusuke Kimura (Aoyama Gakuin University) Kojiro
More informationAERONAUTICAL ENGINEERING
AERONAUTICAL ENGINEERING SHIBIN MOHAMED Asst. Professor Dept. of Mechanical Engineering Al Ameen Engineering College Al- Ameen Engg. College 1 Aerodynamics-Basics These fundamental basics first must be
More informationElectric Drive - Magnetic Suspension Rotorcraft Technologies
Electric Drive - Suspension Rotorcraft Technologies William Nunnally Chief Scientist SunLase, Inc. Sapulpa, OK 74066-6032 wcn.sunlase@gmail.com ABSTRACT The recent advances in electromagnetic technologies
More informationPreliminary Design of a LSA Aircraft Using Wind Tunnel Tests
Preliminary Design of a LSA Aircraft Using Wind Tunnel Tests Norbert ANGI*,1, Angel HUMINIC 1 *Corresponding author 1 Aerodynamics Laboratory, Transilvania University of Brasov, 29 Bulevardul Eroilor,
More informationEnvironmentally Focused Aircraft: Regional Aircraft Study
Environmentally Focused Aircraft: Regional Aircraft Study Sid Banerjee Advanced Design Product Development Engineering, Aerospace Bombardier International Workshop on Aviation and Climate Change May 18-20,
More informationTHE INVESTIGATION OF CYCLOGYRO DESIGN AND THE PERFORMANCE
25 TH INTERNATIONAL CONGRESS OF THE AERONAUTICAL SCIENCES THE INVESTIGATION OF CYCLOGYRO DESIGN AND THE PERFORMANCE Hu Yu, Lim Kah Bin, Tay Wee Beng Department of Mechanical Engineering, National University
More informationAerodynamically induced power loss in hard disk drives
Microsyst Technol (2005) 11: 741 746 DOI 10.1007/s00542-005-0575-8 TECHNICAL PAPER Sung-Oug Cho Æ Seung-Yop Lee Æ Yoon-Chul Rhim Aerodynamically induced power loss in hard disk drives Received: 30 June
More information17/11/2016. Turbomachinery & Heat Transfer Laboratory Faculty of Aerospace Engineering Technion Israel Institute of Technology, Israel
17/11/2016 Turbomachinery & Heat Transfer Laboratory Faculty of Aerospace Engineering Technion Israel Institute of Technology, Israel 1 Motivation New challenges rise due to increase in demands from small
More information(1) Keywords: CFD, helicopter fuselage, main rotor, disc actuator
SIMULATION OF FLOW AROUND FUSELAGE OF HELICOPTER USING ACTUATOR DISC THEORY A.S. Batrakov *, A.N. Kusyumov *, G. Barakos ** * Kazan National Research Technical University n.a. A.N.Tupolev, ** School of
More informationRemote Control Helicopter. Engineering Analysis Document
Remote Control Helicopter By Abdul Aldulaimi, Travis Cole, David Cosio, Matt Finch, Jacob Ruechel, Randy Van Dusen Team 04 Engineering Analysis Document Submitted towards partial fulfillment of the requirements
More informationJay Gundlach AIAA EDUCATION SERIES. Manassas, Virginia. Joseph A. Schetz, Editor-in-Chief. Blacksburg, Virginia. Aurora Flight Sciences
Jay Gundlach Aurora Flight Sciences Manassas, Virginia AIAA EDUCATION SERIES Joseph A. Schetz, Editor-in-Chief Virginia Polytechnic Institute and State University Blacksburg, Virginia Published by the
More informationHeat Transfer Enhancement for Double Pipe Heat Exchanger Using Twisted Wire Brush Inserts
Heat Transfer Enhancement for Double Pipe Heat Exchanger Using Twisted Wire Brush Inserts Deepali Gaikwad 1, Kundlik Mali 2 Assistant Professor, Department of Mechanical Engineering, Sinhgad College of
More informationDevelopment of an Extended Range, Large Caliber, Modular Payload Projectile
1 Development of an Extended Range, Large Caliber, Modular Payload Projectile April 12th, 2011 Miami, Florida, USA 46 th Annual Gun & Missile Systems Conference & Exhibition Speaker: Pierre-Antoine Rainville
More informationWing Cuff Design for Cessna CJ1
Wing Cuff Design for Cessna CJ1 AAE 415 Project Purdue University Saturday, December 10th, 2004 Brian Adams Kevin Clark Greg Davidson Phil Spindler Contents Background of Problem Literature Review Design
More informationReentry Demonstration Plan of Flare-type Membrane Aeroshell for Atmospheric Entry Vehicle using a Sounding Rocket
AIAA ADS Conference 2011 in Dublin 1 Reentry Demonstration Plan of Flare-type Membrane Aeroshell for Atmospheric Entry Vehicle using a Sounding Rocket Kazuhiko Yamada, Takashi Abe (JAXA/ISAS) Kojiro Suzuki
More informationHELICOPTER TAIL ROTOR ANALYSIS: EXPERIENCE IN AGUSTA WITH ADAMS
HELICOPTER TAIL ROTOR ANALYSIS: EXPERIENCE IN AGUSTA WITH ADAMS Bianchi F., Agusta Sp.a. Via G.Agusta, 520 - Cascina Costa di Samarate,Varese - Italy - e-mail: atr@agusta.it Abstract The purpose of the
More informationDesign Considerations for Stability: Civil Aircraft
Design Considerations for Stability: Civil Aircraft From the discussion on aircraft behavior in a small disturbance, it is clear that both aircraft geometry and mass distribution are important in the design
More informationWind Tunnel Measurement Of Aerodynamic Characteristics Of A Generic Eurocopter Helicopter
Wind Tunnel Measurement Of Aerodynamic Characteristics Of A Generic Eurocopter Helicopter by Engr. Assoc. Prof. Dr Shuhaimi Mansor, MIEM, P. Eng. Experimental aerodynamic studies on a generic model of
More informationLarge Area Propellers
Second International Symposium on Marine Propulsors smp 11, Hamburg, Germany, June 2011 Large Area Propellers Daniel Knutsson 1, Lars Larsson 2 1 PhD student, Department of Shipping and Marine Technology,
More informationOn-Demand Mobility Electric Propulsion Roadmap
On-Demand Mobility Electric Propulsion Roadmap Mark Moore, ODM Senior Advisor NASA Langley Research Center EAA AirVenture, Oshkosh July 22, 2015 NASA Distributed Electric Propulsion Research Rapid, early
More informationRevisiting the Calculations of the Aerodynamic Lift Generated over the Fuselage of the Lockheed Constellation
Eleventh LACCEI Latin American and Caribbean Conference for Engineering and Technology (LACCEI 2013) International Competition of Student Posters and Paper, August 14-16, 2013 Cancun, Mexico. Revisiting
More informationSubsonic Parachutes for Future Mars Missions
Subsonic Parachutes for Future Mars Missions John C. Underwood, Arrun Saunders, Steven B. Rogers, J. Stephen Lingard Vorticity Ltd Lionel Marraffa, Luca Ferracina European Space Agency 1 Mars Parachutes
More informationFLIGHT TEST RESULTS AT TRANSONIC REGION ON SUPERSONIC EXPERIMENTAL AIRPLANE (NEXST-1)
26 TH INTERNATIONAL CONGRESS OF THE AERONAUTICAL SCIENCES FLIGHT TEST RESULTS AT TRANSONIC REGION ON SUPERSONIC EXPERIMENTAL AIRPLANE (NEXST-1) Dong-Youn Kwak*, Hiroaki ISHIKAWA**, Kenji YOSHIDA* *Japan
More informationVenus Entry Options Venus Upper Atmosphere Investigations Science and Technical Interchange Meeting (STIM)
Venus Entry Options Venus Upper Atmosphere Investigations Science and Technical Interchange Meeting (STIM) January 24, 2013 at the Ohio Aerospace Institute Peter Gage, Gary Allen, Dinesh Prabhu, Ethiraj
More informationRunning head: GYROSCOPIC STABILIZATION VS. STABILIZATION FINS 1
Running head: GYROSCOPIC STABILIZATION VS. STABILIZATION FINS 1 Gyroscopic Stabilization vs. Stabilization fins in Model Rocketry Donald S. Corp, Maccoy G. Merrell Waxahachie Global High School January
More informationA practical investigation of the factors affecting lift produced by multi-rotor aircraft. Aaron Bonnell-Kangas
A practical investigation of the factors affecting lift produced by multi-rotor aircraft Aaron Bonnell-Kangas Bonnell-Kangas i Table of Contents Introduction! 1 Research question! 1 Background! 1 Definitions!
More informationAmerican International Journal of Research in Science, Technology, Engineering & Mathematics INDIA
American International Journal of Research in Science, Technology, Engineering & Mathematics Available online at http://www.iasir.net ISSN (Print): 2328-3491, ISSN (Online): 2328-3580, ISSN (CD-ROM): 2328-3629
More informationProcedia Engineering 00 (2009) Mountain bike wheel endurance testing and modeling. Robin C. Redfield a,*, Cory Sutela b
Procedia Engineering (29) Procedia Engineering www.elsevier.com/locate/procedia 9 th Conference of the International Sports Engineering Association (ISEA) Mountain bike wheel endurance testing and modeling
More informationFigure 1: Forces Are Equal When Both Their Magnitudes and Directions Are the Same
Moving and Maneuvering 1 Cornerstone Electronics Technology and Robotics III (Notes primarily from Underwater Robotics Science Design and Fabrication, an excellent book for the design, fabrication, and
More informationTHERMAL MANAGEMENT OF AIRCRAFT BRAKING SYSTEM
ABSTRACT THERMAL MANAGEMENT OF AIRCRAFT BRAKING SYSTEM Shivakumar B B 1, Ganga Reddy C 2 and Jayasimha P 3 1,2,3 HCL Technologies Limited, Bangalore, Karnataka, 560106, (India) This paper presents the
More informationUNCLASSIFIED FY 2017 OCO. FY 2017 Base
Exhibit R-2, RDT&E Budget Item Justification: PB 2017 Air Force Date: February 2016 3600: Research, Development, Test & Evaluation, Air Force / BA 2: Applied Research COST ($ in Millions) Prior Years FY
More informationAWIATOR Project Perspectives:
No SBVGs With SBVGs AWIATOR Project Perspectives: Passive Flow Control on Civil Aircraft Flaps using Sub-Boundary Layer Vortex Generators David Sawyers Aerodynamics R&T Co-ordinator Airbus UK Limited KATnet
More informationPrediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM
Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM V Prabhu Raja, J Kanchana, K Ramachandra, P Radhakrishnan PSG College of Technology, Coimbatore - 641004 Abstract Loss of machining
More informationOn Control Strategies for Wind Turbine Systems
On Control Strategies for Wind Turbine Systems Niall McMahon December 21, 2011 More notes to follow at: http://www.niallmcmahon.com/msc_res_notes.html 1 Calculations for Peak Tip Speed Ratio Assuming that
More information31 st National Conference on FMFP, December 16-18, 2004, Jadavpur University, Kolkata
31 st National Conference on FMFP, December 16-18, 24, Jadavpur University, Kolkata Experimental Characterization of Propulsion System for Mini Aerial Vehicle Kailash Kotwani *, S.K. Sane, Hemendra Arya,
More informationModeling, Structural & CFD Analysis and Optimization of UAV
Modeling, Structural & CFD Analysis and Optimization of UAV Dr Lazaros Tsioraklidis Department of Unified Engineering InterFEA Engineering, Tantalou 7 Thessaloniki GREECE Next Generation tools for UAV
More informationLecture 5 : Static Lateral Stability and Control. or how not to move like a crab. G. Leng, Flight Dynamics, Stability & Control
Lecture 5 : Static Lateral Stability and Control or how not to move like a crab 1.0 Lateral static stability Lateral static stability refers to the ability of the aircraft to generate a yawing moment to
More informationThe use of new facility by means internal balance with sting support for wide range Angle of Attack aircraft
Journal of Physics: Conference Series PAPER OPEN ACCESS The use of new facility by means internal balance with sting support for wide range Angle of Attack aircraft To cite this article: Subagyo et al
More informationVALIDATION OF A WALL INTERFERENCE CORRECTION PROCEDURE
ICAS 2002 CONGRESS VALIDATION OF A WALL INTERFERENCE CORRECTION PROCEDURE G. Lombardi, M.V. Salvetti Department of Aerospace Engineering, University of Pisa M. Morelli Medium Speed Wind Tunnel, CSIR, South
More informationChapter 11: Flow over bodies. Lift and drag
Chapter 11: Flow over bodies. Lift and drag Objectives Have an intuitive understanding of the various physical phenomena such as drag, friction and pressure drag, drag reduction, and lift. Calculate the
More informationEnhanced Heat Transfer Surface Development for Exterior Tube Surfaces
511 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 32, 2013 Chief Editors: Sauro Pierucci, Jiří J. Klemeš Copyright 2013, AIDIC Servizi S.r.l., ISBN 978-88-95608-23-5; ISSN 1974-9791 The Italian
More informationSimulation Studies on the Effect of Porous Twisted Plate Inserts on the Performance of Fire Tube Steam Packaged Boiler
Simulation Studies on the Effect of Porous Twisted Plate Inserts on the Performance of Fire Tube Steam Packaged Boiler S. Hassan *,a, M. K. Roslim b and R. M. Zain c Mechanical Engineering Department,
More informationInfluence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating
More informationTELFONA, Contribution to Laminar Wing Development for Future Transport Aircraft. K. H. Horstmann Aeronautical Days, Vienna, 19 th -21 st June 2006
TELFONA, Contribution to Laminar Wing Development for Future Transport Aircraft K. H. Horstmann Aeronautical Days, Vienna, 19 th -21 st June 2006 Content Motivation Determination of transition Objectives
More informationAnalyzing Effect of Tire Groove Patterns on Hydroplaning Speed
Analyzing Effect of Tire Groove Patterns on Hydroplaning Speed S. Santosh KUMAR KUMAR Anupam Graduate Researcher Graduate Researcher Department of Civil Engineering Department of Civil Engineering National
More informationUniversity Of California, Berkeley Department of Mechanical Engineering. ME 131 Vehicle Dynamics & Control (4 units)
CATALOG DESCRIPTION University Of California, Berkeley Department of Mechanical Engineering ME 131 Vehicle Dynamics & Control (4 units) Undergraduate Elective Syllabus Physical understanding of automotive
More informationAdvanced Battery Models From Test Data For Specific Satellite EPS Applications
4th International Energy Conversion Engineering Conference and Exhibit (IECEC) 26-29 June 2006, San Diego, California AIAA 2006-4077 Advanced Battery Models From Test Data For Specific Satellite EPS Applications
More informationProp effects (Why we need right thrust) Torque reaction Spiraling Slipstream Asymmetric Loading of the Propeller (P-Factor) Gyroscopic Precession
Prop effects (Why we need right thrust) Torque reaction Spiraling Slipstream Asymmetric Loading of the Propeller (P-Factor) Gyroscopic Precession Propeller torque effect Influence of engine torque on aircraft
More informationAE 452 Aeronautical Engineering Design II Installed Engine Performance. Prof. Dr. Serkan Özgen Dept. Aerospace Engineering March 2016
AE 452 Aeronautical Engineering Design II Installed Engine Performance Prof. Dr. Serkan Özgen Dept. Aerospace Engineering March 2016 Propulsion 2 Propulsion F = ma = m V = ρv o S V V o ; thrust, P t =
More informationIs Low Friction Efficient?
Is Low Friction Efficient? Assessment of Bearing Concepts During the Design Phase Dipl.-Wirtsch.-Ing. Mark Dudziak; Schaeffler Trading (Shanghai) Co. Ltd., Shanghai, China Dipl.-Ing. (TH) Andreas Krome,
More informationModern Approach to Liquid Rocket Engine Development for Microsatellite Launchers
Modern Approach to Liquid Rocket Engine Development for Microsatellite Launchers SoftInWay: Turbomachinery Mastered 2018 SoftInWay, Inc. All Rights Reserved. Introduction SoftInWay: Turbomachinery Mastered
More informationCoupled Aero-Structural Modelling and Optimisation of Deployable Mars Aero-Decelerators
Coupled Aero-Structural Modelling and Optimisation of Deployable Mars Aero-Decelerators Lisa Peacocke, Paul Bruce and Matthew Santer International Planetary Probe Workshop 11-15 June 2018 Boulder, CO,
More informationGT-Power Report. By Johan Fjällman. KTH Mechanics, SE Stockholm, Sweden. Internal Report
GT-Power Report By Johan Fjällman KTH Mechanics, SE- 44 Stockholm, Sweden Internal Report Presently in the vehicle industry full engine system simulations are performed using different one-dimensional
More informationFABRICATION OF CONVENTIONAL CYLINDRICAL SHAPED & AEROFOIL SHAPED FUSELAGE UAV MODELS AND INVESTIGATION OF AERODY-
ISSN 232-9135 28 International Journal of Advance Research, IJOAR.org Volume 1, Issue 3, March 213, Online: ISSN 232-9135 FABRICATION OF CONVENTIONAL CYLINDRICAL SHAPED & AEROFOIL SHAPED FUSELAGE UAV MODELS
More informationFlight Readiness Review Addendum: Full-Scale Re-Flight. Roll Induction and Counter Roll NASA University Student Launch.
Flight Readiness Review Addendum: Full-Scale Re-Flight Roll Induction and Counter Roll 2016-2017 NASA University Student Launch 27 March 2017 Propulsion Research Center, 301 Sparkman Dr. NW, Huntsville
More informationDesign of A New Non-Contact Screw Seal and Determination of Performance Characteristics
Proceedings of the World Congress on Momentum, Heat and Mass Transfer (MHMT 16) Prague, Czech Republic April 4 5, 2016 Paper No. ENFHT 114 DOI: 10.11159/enfht16.114 Design of A New Non-Contact Screw Seal
More informationVehicle Aerodynamics Subscription Development of Numerical Simulation Method of Flow Around Automobile Using Meshfree Method
Vehicle Aerodynamics Subscription 2005-01-0544 Development of Numerical Simulation Method of Flow Around Automobile Using Meshfree Method 2005-01-0545 A Downforce Optimization Study for a Racing Car Shape
More informationSupersonic Combustion Experimental Investigation at T2 Hypersonic Shock Tunnel
Supersonic Combustion Experimental Investigation at T2 Hypersonic Shock Tunnel D. Romanelli Pinto, T.V.C. Marcos, R.L.M. Alcaide, A.C. Oliveira, J.B. Chanes Jr., P.G.P. Toro, and M.A.S. Minucci 1 Introduction
More informationStructural Strength of Flare-type Membrane Aeroshell Supported by Inflatable Torus against Aerodynamic Force
Structural Strength of Flare-type Membrane Aeroshell Supported by Inflatable Torus against Aerodynamic Force Kazuhiko Yamada (JAXA/ISAS) Takuya Sonoda (Tokai University) Kyoichi Nakashino (Tokai University)
More informationTransient Thermal Analysis of Screw Compressors, Part III: Transient Thermal Analysis of a Screw Compressor to Determine Rotor-to-Rotor Clearances
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 26 Transient Thermal Analysis of Screw Compressors, Part III: Transient Thermal Analysis
More informationComparative blast study of simulation and approximation method of armored vehicles
Comparative blast study of simulation and approximation method of armored vehicles Piangpen Puasopis 1, Attapon Charoenpol 2, Artit Ridluen 3 Defence Technology Institute, Nonthaburi, Thailand 1 Corresponding
More informationY. Lemmens, T. Benoit, J. de Boer, T. Olbrechts LMS, A Siemens Business. Real-time Mechanism and System Simulation To Support Flight Simulators
Y. Lemmens, T. Benoit, J. de Boer, T. Olbrechts LMS, A Siemens Business Real-time Mechanism and System Simulation To Support Flight Simulators Smarter decisions, better products. Contents Introduction
More informationMethodology for Distributed Electric Propulsion Aircraft Control Development with Simulation and Flight Demonstration
1 Methodology for Distributed Electric Propulsion Aircraft Control Development with Simulation and Flight Demonstration Presented by: Jeff Freeman Empirical Systems Aerospace, Inc. jeff.freeman@esaero.com,
More informationComparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2012 Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured
More informationImpacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics
Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics M. Metwally Lecturer, Ph.D., MTC, Cairo, Egypt Abstract Modern offset printing machine, paper
More informationAerodynamic Drag Assessment
Aerodynamic Drag Assessment Computer Fluid Dynamics (CFD) analysis was used in the ULSAB-AVC Program to evaluate the aerodynamic concept from the very beginning of vehicle concepts. 11.1 BACKGROUND A vehicle
More informationAppenidix E: Freewing MAE UAV analysis
Appenidix E: Freewing MAE UAV analysis The vehicle summary is presented in the form of plots and descriptive text. Two alternative mission altitudes were analyzed and both meet the desired mission duration.
More informationDesigning evtol for the Mission NDARC NASA Design and Analysis of Rotorcraft. Wayne Johnson From VTOL to evtol Workshop May 24, 2018
Designing evtol for the Mission NDARC NASA Design and Analysis of Rotorcraft Wayne Johnson From VTOL to evtol Workshop May 24, 2018 1 Conceptual Design of evtol Aircraft Conceptual design Define aircraft
More information850. Design and numerical analysis of a novel coaxial rotorcraft UAV
850. Design and numerical analysis of a novel coaxial rotorcraft UAV Liu Long 1, Ang Haisong 2, Ge Xun 3 College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics Mailbox 172,
More informationDESIGN OF ACTIVE FLOW CONTROL AT THE WING/PYLON/ENGINE JUNCTION
DESIGN OF ACTIVE FLOW CONTROL AT THE WING/PYLON/ENGINE JUNCTION A. PRACHAŘ, P. VRCHOTA / VZLU A. GEBHARDT, J. WILD / DLR S. WALLIN / KTH D. HUE / ONERA M. MINERVINO / CIRA Coordinator : Martin Wahlich
More informationMembrane Wing Aerodynamics for µav Applications
Membrane Wing Aerodynamics for µav Applications Wei Shyy, Yongsheng Lian & Peter Ifju Department of Mechanical and Aerospace Engineering University of Florida Gainesville, FL 32611 Wei-shyy@ufl.edu Department
More informationFINAL REPORT MARCH 2008
AIRFLOW ASSESSMENT OF NOVEL VENTILATION AND MOISTURE DRAINAGE HOLES FINAL REPORT MARCH 2008 Daniel James, Richard Adamec Centre for Wireless Monitoring and Applications Griffith University CWMA WEEPA Ventilation
More informationPVP Field Calibration and Accuracy of Torque Wrenches. Proceedings of ASME PVP ASME Pressure Vessel and Piping Conference PVP2011-
Proceedings of ASME PVP2011 2011 ASME Pressure Vessel and Piping Conference Proceedings of the ASME 2011 Pressure Vessels July 17-21, & Piping 2011, Division Baltimore, Conference Maryland PVP2011 July
More informationEvaluation of the Applicability of the Vortex Lattice Method to the Analysis of Human Powered Aircraft
McNair Scholars Research Journal Volume Article Evaluation of the Applicability of the Vortex Lattice Method to the Analysis of Human Powered Aircraft Armando R. Collazo Garcia III Embry-Riddle Aeronautical
More informationComputer Aided Engineering in Ni Electroforming to Fight Off the Effects of Abrasive Sand on Erosion Shields Performance
Computer Aided Engineering in Ni Electroforming to Fight Off the Effects of Abrasive Sand on Erosion Shields Performance Agnieszka Franczak, Elsyca NV, Belgium ASETSDefense Workshop 2018 Denver, Colorado,
More informationFSI and Modal Analysis of Elastic Ring Squeeze Film Damper for Small Gas Turbine Engines
FSI and Modal Analysis of Elastic Ring Squeeze Film Damper for Small Gas Turbine Engines Thennavarajan Subramanian 1*, Jeyaraj P 2, Manikandan L P 3, S S Kulkarni 4, Soumendu Jana 5 Technical Officer,
More informationTWO PLANE BALANCING OF A CONICAL ROTOR DRIVEN BY VERTICAL BELT SYSTEM DESIGNED TO REDUCE GYRO EFFECT
Int. J. Mech. Eng. & Rob. Res. 2012 V Deepika Poornima et al., 2012 Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 1, No. 3, October 2012 2012 IJMERR. All Rights Reserved TWO PLANE BALANCING OF A CONICAL
More informationFE151 Aluminum Association Inc. Impact of Vehicle Weight Reduction on a Class 8 Truck for Fuel Economy Benefits
FE151 Aluminum Association Inc. Impact of Vehicle Weight Reduction on a Class 8 Truck for Fuel Economy Benefits 08 February, 2010 www.ricardo.com Agenda Scope and Approach Vehicle Modeling in MSC.EASY5
More informationRotorcraft Gearbox Foundation Design by a Network of Optimizations
13th AIAA/ISSMO Multidisciplinary Analysis Optimization Conference 13-15 September 2010, Fort Worth, Texas AIAA 2010-9310 Rotorcraft Gearbox Foundation Design by a Network of Optimizations Geng Zhang 1
More informationExperimental Study of Heat Transfer Augmentation in Concentric Tube Heat Exchanger with Different Twist Ratio of Perforated Twisted Tape Inserts
International search Journal of Advanced Engineering and Science Experimental Study of Heat Transfer Augmentation in Concentric Tube Heat Exchanger with Different Twist Ratio of Perforated Twisted Tape
More informationAPPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE
Colloquium DYNAMICS OF MACHINES 2012 Prague, February 7 8, 2011 CzechNC APPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE Jiří Šimek Abstract: New type of aerodynamic
More informationMSC/Flight Loads and Dynamics Version 1. Greg Sikes Manager, Aerospace Products The MacNeal-Schwendler Corporation
MSC/Flight Loads and Dynamics Version 1 Greg Sikes Manager, Aerospace Products The MacNeal-Schwendler Corporation Douglas J. Neill Sr. Staff Engineer Aeroelasticity and Design Optimization The MacNeal-Schwendler
More information