TBHD1 CRIMPING TOOL FOR THOMAS & BETTS TS DIES
|
|
- Jeremy Burns
- 6 years ago
- Views:
Transcription
1 TBHD1 CRIMPING TOOL FOR THOMAS & BETTS TS DIES DATASHEET SEE PAGE 6 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY Operating instructions for the TBHD1 crimping tool using the HPU10 air/hydraulic pump or the hand operated MHP-1 hydraulic pump BRIDGE BRIDGE PIN PIVOT PIN FILLER CAP CLOSE STATIONARY DIE MOVABLE DIE OPEN VALVE KNOB MHP-1 HYDRAULIC PUMP FIGURE 1 TBHD1 CRIMPING TOOL QUICK CONNECTION INSTALLING DIES: 1. Pull both pivot and bridge pins to remove the bridge as shown in Figure Place the movable die half between the die rails. Carefully lower the die and mate the die snap retainer to the snap retainer located in the ram as shown in Figure Place the stationary die half between the rails and lower it so the flat spring fits into the spring recess of the die rails. 4. Replace the bridge onto the die rails and snap the stationary die into the mating snap located in the bridge. 5. Replace both the bridge and pivot pins. (CAUTION: THE STATIONARY DIE SNAP AND BRIDGE SNAP RETAINERS MUST BE FULLY EN- GAGED BEFORE THE PINS CAN BE INSTALLED.) CAUTION: DO NOT OPERATE THIS TOOL WITHOUT A DIE SET INSTALLED AND THE BRIDGE PROPERLY ATTACHED AND LOCKED WITH THE BRIDGE PIN AND PIVOT PIN. COPYRIGHT 2002 ALL RIGHTS RESERVED 1
2 STATIONARY DIE SNAP FLAT DIE SPRING BRIDGE SNAP RETAINER RAM SNAP DIE SNAP RETAINER MOVABLE DIE SNAP FIGURE 2 FLAT DIE SPRING RECESS CONDUCTOR PREPARATION: Using a proper insulation stripping tool, strip the insulation from the conductor, being careful not to nick the wire strands. Thoroughly clean the conductor by wire brushing until a bright and shiny surface is obtained. All oxides and foreign matter must be removed. NOTE: Do not wire brush tin plated copper conductors. OPERATING INSTRUCTIONS USING THE MHP-1 HAND OPERATED HYDRAULIC PUMP 1. Connect the male half of the hose quick connector to the female half of the quick connector located on the crimping head (see Figure 1). 2. This hand pump can be operated in the horizontal or vertical position when the pump head is pointing down. 3. To extend the cylinder and make a crimp, turn the valve knob clockwise to a closed position, work the handle up and down to build pressure (see Figure 1). 4. To release pressure and retract the movable die turn the valve knob counter clockwise until the die is fully open. CRIMPING A TERMINAL LUG: 1. Place a lug in the movable die making sure the lug is positioned as shown in Figure Close the hand pump valve knob and pump the handle until the dies LOOSELY clamp the lug (see Figure 4). COPYRIGHT 2002 ALL RIGHTS RESERVED 2
3 DO NOT REMOVE FILLER CAP TOP VIEW OIL LEVEL END VIEW FIGURE 3 3. Insert the conductor into the lug's socket, making sure that the conductor is pushed fully into the lug's crimping area (see Figure 4). 4. Actuate the pump handle and the movable die will start compressing the lug. The crimp is completed when the two dies halves are fully closed. 5. When the die halves are fully closed rotate the valve knob counterclockwise to release and return the movable die to the open position (see Figure 1). CAUTION: IT IS THE OPERATOR'S RESPONSIBILITY TO MAKE SURE THE DIES ARE FULLY CLOSED. FULL DIE CLOSURE IS NECESSARY TO PRODUCE A PROPER CRIMP. CHECKING THE OIL LEVEL AND REFILLING THE OIL RESERVOIR; MHP-1 1. Removed the filler cap shown in Figure 3. The oil level should come to filler hole when the pump is resting on its base and cylinder retracted. 2. Turn the valve handle to release all the pressure and retract the cylinder. Cylinders must always be retracted when checking or adding oil. 3. Clean the area around the filler cap. Remove the filler cap, and position the pump with the head down and the filler hole up. Insert a clean funnel with a filter into the filler hole. 4. Fill the pump with a high-grade hydraulic oil such as Paradene ISO 46(10) part no Place the pump on its base without the filler cap installed, and let the excess oil drain out (see Figure 3). 6. Replace filler cap. COPYRIGHT 2002 ALL RIGHTS RESERVED 3
4 STATIONARY DIE HALF CRIMP LUG MOVABLE DIE HALF FIGURE 4 OPERATING INSTRUCTIONS USING THE HPU10 COMPRESSED AIR/HYDRAULIC PUMP. GENERAL: The HPU10 is an air over hydraulic pump capable of delivering (10,000 PSI) of hydraulic pressure. To assure the operator has made an acceptable crimp the unit uses DMC Cycle Control Logic. Once the foot pedal is pressed and the cycle begins, the pump will not stop until it reaches its set point (9000 PSI Factory Set). When the set point is reached the unit will stop pumping and release the system pressure, opening the dies. OPERATING INSTRUCTIONS PUMP SETUP CHECKING THE OIL LEVEL IN THE RESERVOIR HPU10 CAUTION: WHEN ADDING OR CHECKING OIL THE RAM MUST BE IN THE FULLY RETRACTED POSITION (NO PRESSURE IN THE SYSTEM). 1. Position the pump unit so the front panel is facing up (resting on its back). 2. Clean the area around the filler cap and remove the cap located on the left side of the front panel. Wipe the indicating rod free of any oil. 3. Insert rod into the tank (No need to screw down) and determine that the level of oil is at least equal to or above the mark on the indicating rod (see Figure 5). COPYRIGHT 2002 ALL RIGHTS RESERVED 4
5 EMERGENCY STOP BUTTON FILLER CAP FOOT PRESS AIR INLET FIGURE 5 4. Refill with Paradene ISO 46 (10) Part No Drydenoil Corp. Baltimore MD (410) or a suitable oil meeting the above requirements. 5. Connect a clean air supply of PSI to the inlet nipple located on the lower right front panel of the pump case. 6. Connect the two foot valve quick couplers to their respective mating connectors located on the lower corner of the front panel. Proper connection is assured by the configuration of the coupler. EMERGENCY STOP BUTTON (ESB): When activating the Emergency Stop Button (located on the top of the unit) the pump will stop pumping and the pressure in the system will be released (see Figure 5). EMERGENCY PROCEDURES 1. NEVER REMOVE THE AIR LINE IN HOPES OF RETRACTING THE DIES. 2. PRESS THE EMERGENCY STOP BUTTON. ANY TIME THE ESB IS ACTUATED THE PUMPING WILL STOP AND THE HYDRAULIC PRESSURE WILL BE RELEASED. EMERGENCY STOP INFORMATION APPEARS ON A LABEL WHICH IS AFFIXED TO THE CASE NEXT TO THE EMERGENCY STOP BUTTON. IF THIS BECOMES LOST OR ILLEGIBLE, CONTACT DMC FOR A REPLACEMENT. COPYRIGHT 2002 ALL RIGHTS RESERVED 5
6 CRIMPING A TERMINAL LUG: 1. Place a lug with the conductor fully inserted into the wire barrel as shown (see Figure 4). 2. Actuate the foot pedal and the movable die will start compressing the lug. The crimp is completed when the HPU10 pump cycles and opens the dies fully. 3. For additional crimping instructions refer to the guidelines supplied by the terminal manufacturer, crimp die set manufacturer, or the system manager. Daniels Manufacturing Corporation offers complete refurbishing and recalibration services. DMC specially engineers and manufacturers complete tool kits to satisfy individual customer requirements, such as total aircraft support, general shop maintenance or production, on board ship and vehicle service, etc. LIMITATION OF LIABILITY Daniels Manufacturing Corporation is not liable for consequential or special damages of any nature or kind resulting from the use, or misuse, of any of its products. Owners and users of DMC products assume full responsibility for instructing their employees in the proper and safe use of such products. LIMITED WARRANTY DMC ( Daniels Manufacturing Corporation) warrants each new product sold by it to be free from defects in material and workmanship under normal use and service. DMC's obligation under this warranty is limited to the free correction or, at DMC's option, the refund of the purchase price of any such product which proves defective in normal service within ninety (90) days after delivery to the first user, provided that the product is returned to DMC with all transportation charges prepaid and which shall appear to DMC's satisfaction, after DMC's inspection, to have been defective in material or workmanship, it been understood that DMC products are not consumer products. This warranty shall not cover any damage to any product which, in the opinion of DMC, was caused by normal wear, misuse, improper operation, tampering, neglect or accident. This warranty is in lieu of all other warranties express or implied. No warranty, express or implied, is made or authorize to be made or assumed with respect to products of Daniels Manufacturing Corporation other than those herein set forth. COPYRIGHT 2002 ALL RIGHTS RESERVED 6
SCT SERIES PRE-SET TENSION SAFE-T-CABLE APPLICATION TOOL
SCT SERIES PRE-SET TENSION SAFE-T-CABLE APPLICATION TOOL DATASHEET SEE PAGE 10 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY INTRODUCTION The Daniels SCT Series Safe-T-Cable
More informationHXE4B BATTERY POWERED CRIMP TOOL
Description The HXE4B Battery Powered Crimp Tool is a hand held, self contained crimp tool intended to crimp copper and aluminum cable with DMC Y dies. Safety Safety is essential in the use and maintenance
More informationCORPORA 110N DATASHEET I SEE PAGE 4 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY. I
BT-ST-751 TORQUE WRENCH Dl DANIELS....., MANUFACTURING CORPORA 110N I SEE PAGE 4 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY. I OPERATING INSTRUCTIONS PLEASE READ
More informationHDE36B BATTERY POWERED CRIMP TOOL
Description The HDE36B Battery Powered Crimp Tool is a hand held, self contained crimp tool intended to crimp copper and aluminum cable with DMC HD36 dies. KEEP THIS MANUAL Important Safety Information
More informationME310B BATTERY POWERED CRIMP TOOL
Description The ME310B Battery Powered Crimp Tool is a hand held, self contained crimp tool intended to crimp machined contacts onto copper and aluminum cable. KEEP THIS MANUAL Important Safety Information
More informationAFE8B BATTERY POWERED CRIMP TOOL
Description The AFE8B Battery Powered Crimp Tool is a hand held, self contained crimp tool intended to crimp machined contacts onto copper and aluminum cable. KEEP THIS MANUAL Important Safety Information
More informationHDE36 BATTERY POWERED CRIMP TOOL
Description The HDE36 Battery Powered Crimp Tool is a hand held, self contained crimp tool intended to crimp copper and aluminum cable with DMC HD36 dies. Important Safety Information Safety Safety is
More informationSEE PAGE 5 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY AIR SUPPLY FITTING (SS) QA SERIES
WA, WAP & WAF QA SERIES AUTOMATIC CRIMPING TOOLS (INCLUDING SS VERSION) DATASHEET SEE PAGE FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY AIR SUPPLY FITTING SIDE (SS)
More informationABOT4001 REV1 BATTERY POWERED CRIMP TOOL
Figure 1 Description The ABOT4001 rev1 is a handheld Battery Powered Crimp tool. It uses dies engineered to meet the requirements of the AS22520/40-01 and is intended to crimp insulated terminals, splices,
More informationSEE PAGE 4 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY. Operating Instructions. Please read before use
STATIC TORQUE METER SEE PAGE 4 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY. Operating Instructions Please read before use 0-200 in. lbs. torque range Increment markings
More informationMPT-250B SPECIFICATIONS AND OPERATING INSTRUCTIONS
1. SAFETY The MPT-250B Wire Crimp Pull Tester is a force measurement device, and as such should be operated with due caution. Operators should wear safety glasses for eye protection because the crimp under
More informationMPT-200A SPECIFICATIONS AND OPERATING INSTRUCTIONS
MPT-200A SPECIFICATIONS AND OPERATING INSTRUCTIONS DATASHEET 1. SAFETY The MPT-200A Wire Crimp Pull Tester is a force measurement device, and as such should be operated with due caution. Operator should
More informationUtility Controller Hand Air Operated
Utility Controller Hand Air Operated P-1395 819-0288 Installation Instructions Introduction The Warner Electric air/manual Utility Controller combines manual and automatic (air) actuation for the operation
More informationMODEL G300 BRAKE BLEEDER
MODEL G300 BRAKE BLEEDER Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV120716 P/N: 81-0035H THIS PAGE INTENTIONALLY
More informationOperating Instructions and Parts Manual Long Chassis Service Jacks
Operating Instructions and Parts Manual Long Chassis Service Jacks Models JSJ-3T/JSJ-5T/JSJ-10T WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-454430 Ph.: 800-274-6848 Revision A 8/05
More informationMODEL 5120 Tire Repair Station
MODEL 5120 Tire Repair Station 00-0049 Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV01182017 P/N: 81-0058G CAUTION
More informationSafety Sentry Electronic Breakaway Switch
Safety Sentry Electronic Breakaway Switch P-616-WE 819-0454 Installation Instructions An Altra Industrial Motion Company Parts List Mounting hardware included with the Safety Sentry Breakaway Switch kit:
More informationHydraulic Transmission Jacks
Hydraulic Transmission Jacks Operating Instructions & Parts Manual Model Number Atd-7435 Atd-7436 Atd-7437 Capacity 1100 Lb. 2000 Lb. 3000 Lb. Model Atd-7435 Model Atd-7436 Model Atd-7437 Atd Tools Inc.
More informationAir Actuated Hydraulic Bottle Jacks
Air Actuated Hydraulic Bottle Jacks Operating Instructions & Parts Manual Model Number Atd-7412 Atd-7420 Capacity 12 Ton 20 Ton Atd Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 Printed in China
More informationTelescopic Transmission Jacks
Telescopic Transmission Jacks Operating Instructions & Parts Manual Model Number BH7051 BH7055 (Air/Manual) Capacity 1/2 Ton 1/2 Ton SFA Companies 2006 10939 N. Pomona Ave. Kansas City, MO 64153 816-891-6390
More informationMODEL TON HYDRAULIC FLOOR JACK
MODEL 66510 10 TON HYDRAULIC FLOOR JACK USER'S MANUAL *This hydraulic jack conforms to all "ANSI / ASME" safety standards. Jackco Transnational Inc. 2010 South El Monte, CA 888-452-2526 To see more jackco
More informationMODEL TON HYDRAULIC FLOOR JACK
MODEL 66500 5 TON HYDRAULIC FLOOR JACK USER'S MANUAL *This hydraulic jack conforms to all "ANSI / ASME" safety standards. Jackco Transnational Inc. 2010 South El Monte, CA 888-452-2526 To see more jackco
More informationLUBRICATOR GUN INSTRUCTIONS-PARTS LIST. 10,000 psi (700 bar) Maximum Delivery Pressure. Detachable-type
INSTRUCTIONS-PARTS LIST 306 460 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. E Supercedes D Detachable-type LUBRICATOR GUN 10,000 psi (700 bar)
More informationATD-7391A 10-Ton Long Chassis Service Jack Owner s Manual
ATD-7391A 10-Ton Long Chassis Service Jack Owner s Manual Specifications Features: Made in China to ATD Tools, Inc. Specifications Visit us at www.atdtools.com ATD7391A_rev_0318 NOTE: 1. SAFETY maintenance.
More informationWarner Electric UNIBRAKE Motor Brakes
P-1699-WE Warner Electric UNIBRAKE Motor Brakes Installation & Operating Instructions Double C Contents General Information........................ 2 Brake Heads............................. 2 Installation...............................
More informationLubricator Gun: 10,000 psi (700 bar) Maximum Delivery Pressure when disconnected from Dispenser
INSTRUCTIONS-PARTS LIST 30 455 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. C Supercedes B Hand-Operated Portable Grease Dispenser Buckshot Luber
More information22/35 Two Stage Truck Jack
Model 1003 CAPACITY RATCHETING JACK STAND DO NOT OVERLOAD AND. ST OVERLOADING CAN CAUSE DAMAGE AILURE TO,, OF OR ENSURE F BOTH ANDS ST ARE SET T SAME HEIGHT & HOLDING DOGS Y ENGAGED. ARE FULL THE ST AND.
More informationHydraulic Truck Jack
Operating Instructions & Parts Manual Hydraulic Truck Jack Model Capacity 23221C 22 Ton 23222C (Low Profile) 22 Ton 23301 30 Ton Models 23221C & 23222C Model 23301! U.S. Patent No's. 5,341,723 & 5,94,912
More informationINSTALLATION INSTRUCTIONS
Safety Notices... 1... 3 Specifications... 3 General... 3 Electrical... 3 Hydraulic Connections... 3 Components... 4 Assembly... 4 Implement Installation... 7 Hydraulic Connections... 9 Closed-Center Hydraulics...
More information12 Volt Utility Controller for 4, 6 or 8 Brakes No P
12 Volt Utility Controller for 4, 6 or 8 Brakes No. 1300-77 P-1379 819-0094 Installation Instructions Introduction The Warner Electric manually operated Utility Controller operates 4, 6, or 8 twelve-volt
More information12 Volt Utility Controller for 4, 6, or 8 Brakes No
12 Volt Utility Controller for 4, 6, or 8 Brakes No. 1300-76 P-1396-WE 819-0301 Installation Instructions An Altra Industrial Motion Company Contents Introduction... 2 Installation... 3 Mounting Under
More informationInstallation & Operation Manual. Electrak 100 Series / Electromechanical Linear Actuator
www..c Installation & Operation Manual Electrak 100 Series / Electromechanical Linear Actuator Thomson has many years of experience designing and manufacturing linear actuators for a wide variety of applications
More informationWEAVER JACK CORP. MASTER PARTS PRICE & IDENTIFICATION LIST. (517) Fax (517) MINIMUM BILLING $20.00
EFFECTIVE JULY 1, 2014 WEAVER JACK CORP. MASTER PARTS PRICE & IDENTIFICATION LIST (517) 263-6500 Fax (517) 263-2810 MINIMUM BILLING $20.00 THIS PRICE LIST SUPERSEDES ALL PREVIOUS PARTS PRICE LISTS (Prices
More informationMODEL G300 Brake Bleeder
MODEL G300 Brake Bleeder Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 Rev013107 P/N: 81-0035C CAUTION Before using
More information2 Speed Hydraulic Hand Pump
Porto-Power Blackhawk Automotive is a licensed trademark 2 Speed Hydraulic Hand Pump Operating Instructions & Parts Manual B65122 B65421 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 816-891-6390
More information76" H x 36" W x 27" D. 80" H x 38" W x 48" D. Maximum 150 psi Standard shop air (8 100 psi)
Part# 26BPAC - Pack-Master Air Compactor The Pack-Master Air is the best value for a pneumatic waste compactor. With the Pack-Master Air, you can effortlessly compact material in a 30 or 55 gallon drum
More informationANDERSON Products OWNER OPERATION MANUAL VC6FTR-SP, VC6R-SP, VC7FTR-SP, & VC7R-SP
OWNER OPERATION MANUAL VERSA-CRIMP HYDRAULIC REMOTE HEAD TOOLS VC7FTR-SP, & VC7R-SP Read and understand all of the instructions and safety information in this manual before operating or servicing these
More informationDISCONTINUED VERSION Parts listed in this catalog may no longer be available. ILLUSTRATED PARTS CATALOG BUNN-O-MATIC CORPORATION
8 4 0 0 1 BUNN Espress ES 2C DISCONTINUED VERSION Parts listed in this catalog may no longer be available. 12 0,5 1,5 CL 2 16 2,5 CAUTION HOT Liquid-Steam-Surfaces OFF ON ILLUSTRATED PARTS CATALOG Designs,
More informationOperating Instructions & Parts Manual. Air/Manual Hydraulic Bottle Jacks
J18124-M1_032015 Operating Instructions & Parts Manual Air/Manual Hydraulic Bottle Jacks Model J18124 J18204 Capacity 12 Ton 20 Ton U.S. Patent Nos. 6,012,377-5,946,912! This is the safety alert symbol.
More informationContinental Super Flow
WARNING Refer to Material Safety Data Sheets (MSDS) and other pertinent safety requirements associated with the handling and application of anhydrous ammonia with a local anhydrous ammonia supplier. It
More informationLong Chassis Hydraulic Service Jacks
Model BH6011 Long Chassis Hydraulic Service Jacks Operating Instructions and Parts Manual Capacity 10 Ton Model BH6011 U.S. Patent No's. 5,946,912 5,341,723! This is the safety alert symbol. It is used
More informationManual Operated Floor Jack
Manual Operated Floor Jack OPERATING INSTRUCTIONS Note: There may be some slight differences in the appearance of the various manually-operated floor jacks, however the instructions in this manual apply
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save Save This This Manual Keep Keep this this manual manual for for the the safety safety warnings warnings and and precautions, assembly, assembly, operating, inspection,
More informationHydraulic Clutch Jack
Hydraulic Clutch Jack Operating Instructions & Parts Manual Model Number Atd-7404 Capacity 500 Lb. Atd Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 Printed in China ATD7404-M0 05/07 Save these
More information1250 LB. CAPACITY MECHANICAL WHEEL DOLLY
1250 LB. CAPACITY MECHANICAL WHEEL DOLLY 67287 SET-UP AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result
More informationPack-Master Air, Spark Resistant Product Manual
Pack-Master Air, Spark Resistant Product Manual Pack-Master Air, Spark Resistant Manual TABLE OF CONTENTS Precautionary Warning... Page 1 Removing Unit from Pallet. Page 2 Wheel Kit (optional) Page 2 Connecting
More informationINSTALLATION AND OPERATIONS MANUAL POWER OPERATED TUBING STORAGE REEL MODEL TSR-P PRODUCTS, INC.
INSTALLATION AND OPERATIONS MANUAL POWER OPERATED TUBING STORAGE REEL MODEL TSR-P 5 PRODUCTS, INC. 1225 Davis Road Elgin, IL 60123 Phone (847) 695-9000 Fax (847) 695-9078 POWER REEL PUBLICATION TSRP0413
More informationLong Chassis Hydraulic Service Jacks
Long Chassis Hydraulic Service Jacks Operating Instructions & Parts Manual Model Number Atd-7390 Atd-7391 Capacity 5 Ton 10 Ton Atd Tools Inc. 160 Enterprise Drive, Wentzville MO 63385 Printed in China
More informationOWNER S MANUAL PRODUCT CODE: 2006T
Jul-18 Product Code: 2006T OWNER S MANUAL PRODUCT CODE: 2006T HYDRAULIC PIPE BENDER 12,000KG Model Capacity Bending Die No of Attachments 12,000kg 1/2", 3/4", 1", 1-1/4", 1-1/2", 2" 6 Made in China to
More informationMODEL HD-BTC. Installation, Operation & Repair Parts Information REV041416
MODEL HD-BTC Installation, Operation & Repair Parts Information REV041416 TABLE OF CONTENTS SAFETY INSTRUCTIONS 1 DEFINITIONS 1 SPECIFICATIONS 2 INSTALLATION INSTRUCTIONS 2 OPERATING INSTRUCTIONS 2 MAINTENANCE
More informationHydraulic Transmission Jack, Telescopic
Operating Instructions & Parts Manual Hydraulic Transmission Jack, Telescopic Model 4000 400 (Air Operated) Capacity 000 lbs. 000 lbs. Model 4000 Model 400 U.S. Patent No. 6,02,377! This is the safety
More informationOwner s Manual Nitrate Series Salt Based Filter System
Owner s Manual Nitrate Series Salt Based Filter System Page 2 Copyright 2012 Enviro Water Solutions Inc. All rights reserved. All information contained herein is the property of Pelican Water Systems.
More information"WHERE TUBING AND FITTINGS COME TOGETHER"
CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD200SS TUBE EXPANDER OPERATIONS MANUAL VERSION 4.3 LAST EDITED 06.17.15 cleanroomdevices.com Table of Contents Table of Contents....1
More informationAdapter. Owner's Manual & Warranty. Item# JSFSA. Compatible with Weego Jump Starter Battery+ Models JS 12 & JS 18
Adapter Item# JSFSA Owner's Manual & Warranty Compatible with Weego Jump Starter Battery+ Models JS 12 & JS 18 Learn About Your Wee go 12V DC Adapter! There are so many tools and accessories you can power
More information1500 Series Roll Off Hoist. Owner s Manual (5-06)
1500 Series Roll Off Hoist Owner s Manual (5-06) Section 1: General Information Introduction Safety Information Warranty Information Table of Contents Section 2: Operation Operating the P.T.O. Operating
More informationAir Actuated Hydraulic Treadle Pump
Porto-Power Blackhawk Automotive is a licensed trademark Air Actuated Hydraulic Treadle Pump Operating Instructions & Parts Manual B65425 B65426 B65427 SFA Companies 2005 10939 N. Pomona Ave. Kansas City,
More informationHeavy Duty Bottle Jacks
Heavy Duty Bottle Jacks Models: 10300 & 10500 10300 10500! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol
More information8700 Series 8900 Series Rolling Air Jacks
8700 Series 8900 Series Rolling Air Jacks Installation, Operation & Repair Parts Information - NOTICE - AIR SUPPLY MUST HAVE IN-LINE FILTER/REGULATOR/LUBRICATOR (NOT INCLUDED) TO VALIDATE THE ROLLING AIR
More informationHeavy Duty Engine Cranes
Heavy Duty Engine Cranes Operating Instructions & Parts Manual Model Number Atd-7484 Atd-7485 (Foldable Legs) Capacity 2 Ton 2 Ton Model Atd-7484 Model Atd-7485 Atd Tools Inc. 160 Enterprise Drive, Wentzville,
More informationCompressor Clutch Replacement Procedure
Clutch Replacement Procedure P-1401-WE 819-0316 Installation Instructions An Altra Industrial Motion Company Warner Replacement Clutches for the following compressors: Denso 6E171 10P15 6P148 6C17 Ford
More informationAutomotive Air Conditioning Manifold Gauge Sets
Automotive Air Conditioning Manifold Gauge Sets 1 Caution: These instructions are not for use with Hybrid Vehicles. For instructions for servicing Hybrid Vehicles use Hybrid Vehicle manufacturer s service
More informationAir Actuated Hydraulic Bottle Jack on Wheels
Operating Instructions & Parts Manual Air Actuated Hydraulic Bottle Jack on Wheels Model Number 18127 18207 Capacity 12 Ton 20 Ton Shinn Fu Co. of America, Inc. 2002 10939 N. Pomona Avenue Kansas City,
More informationANDERSON Products OWNER OPERATION MANUAL VC6FT-SP, VC63-SP, VC7-SP, & VC7FT-SP
OWNER OPERATION MANUAL VERSA-CRIMP HYDRAULIC CRIMPING HAND TOOLS Read and understand all of the instructions and safety information in this manual before operating or servicing these tools. TABLE OF CONTENTS
More informationGW-120 Bar Glass Washer
GW-120 Bar Glass Washer This manual contains important information regarding your Admiral Craft unit. Please read this manual thoroughly prior to product setup, operation and maintenance. Failure to comply
More informationInstallation Instructions
Installation Instructions Individual Built-In Wall Shower with Concealed Supplies Table of Contents Pre-Installation Information...2...3 Repair parts...4 Metering Valve Troubleshooting...5 Cleaning and
More informationInstallation Instructions Receiver Rack (Part # 7700) Universal Application
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty Tools Needed 2 Draw Bar 1 Ratchet Racks 2 Socket Set Curved Support Bars 2 Wrench Set Connecting
More informationATD Gallon Pressurized Oil Drain Owner s Manual
ATD-5203 30 Gallon Pressurized Oil Drain Owner s Manual TECHNICAL SPECIFICATIONS Model: ATD-5203 Capacity: 30 Gallon Drain Funnel Working Height: 47.25 to 70.5 Drain Funnel Diameter: 15.75 Plastic Tray:
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationSYSTEM CONTROL KIT. Model: CK-41F. Designed for use with the SWG Series Power Venter for controlling Natural Gas or L.P. Gas appliances.
SYSTEM CONTROL KIT Model: CK-41F Designed for use with the SWG Series Power Venter for controlling Natural Gas or L.P. Gas appliances. ITEMS INCLUDED IN KIT: 1- Junction box with mounted pressure switch
More informationInstallation Guide. Marking and Inspection Gauge. Marking Gauge. Inspection Gauge E 1. Marking and inspection gauges are combined into one gauge.
Marking and Inspection Gauge Marking and inspection gauges are combined into one gauge. Marking Gauge The gauge has a pin and a slot for marking along the centerline. Position the pin with the end of the
More informationHydraulic Long Jacks
Operating Instructions & Parts Manual Hydraulic Long Jacks Model 44915 44930 44940 44980 44981C (Air option) Capacity 1-1/2 Ton 3 Ton 4 Ton 8 Ton 8 Ton Models 44915, 44930, 44940 & 44980 Model 44981C U.S.
More informationMODEL L/R/EF Sectional Tire Spreader
MODEL L/R/EF Sectional Tire Spreader Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV08032016 P/N: 81-0195E TABLE
More informationModel 340 Tune-Up Kit Instructions
Model 340 Tune-Up Kit Instructions Jacobs P/N 019654 tune-up kit instructions Tune-up Kit Contents Illus. No. Jacobs P/N Part Name Quantity Per Kit 4 020229 Upper Seal Ring 3 5 001082 Center Seal Ring
More informationIMPORTANT SAFETY INFORMATION
Specifications Tricycle Height 26 Front Wheel 5/8 Axle Diameter, 13 Pneumatic Knobby Tire Back Wheels 5/8 Axle Diameter, 10 Pneumatic Knobby Tire Age Range 5 and up Weight Capacity 150 lb. IMPORTANT SAFETY
More informationTechcon Systems TS5000 Series Rotary Valve
10. SPARE PARTS AND ACCESSORIES 10.1 SPARE PARTS: The only spare parts available are: Fluid inlet fitting, O- ring and clean out screw. These items are included in the Valve cleaning kit part number: 5000-013-000
More informationMODEL TC400 TIRE CART. Installation, Operation & Repair Parts Information REV P/N:
MODEL TC400 TIRE CART Installation, Operation & Repair Parts Information REV061614 P/N: 81-0245 1 TABLE OF CONTENTS SAFETY INSTRUCTIONS 2 DEFINITIONS 2 SPECIFICATIONS 3 INSTALLATION INSTRUCTIONS 3 OPERATING
More informationOperating Instructions & Parts Manual
Swift Lift Hydraulic Service Jack Operating Instructions & Parts Manual Model Number ATD7341 Capacity 3-1/2 Ton U.S. Patent No's. 5,946,912 6,199,379! This is the safety alert symbol. It is used to alert
More informationTissue Master. User Manual
Tissue Master User Manual This page left blank intentionally This manual is a guide for the use of the Omni International Tissue Master and accessories. Data herein has been verified and validated. It
More informationMODEL 5500 Tire Repair Station
MODEL 5500 Tire Repair Station Installation, Operation and Repair Parts Information Branick Industries, Inc. 4245 Main Ave P.O. Box 1937 Fargo, North Dakota 58103 P/N: 81-0047C TABLE OF CONTENTS SAFETY
More information8" - 12" Hydraulic Steel Squeeze Off Tool
8" - 12" Hydraulic Steel Squeeze Off Tool ECN 19130 C812S Hydraulic Steel Squeeze Off Tool for Steel Pipe Page 1 of 8 This Footage Tools C812S Steel Squeeze Off Tool is sold with one pump configuration
More informationCompressor Clutch Replacement Procedure
P-1411 819-0361 Compressor Clutch Replacement Procedure Installation Instructions World Clutch with Unidamp Armature for Ford FX-15 and FS-10 Compressors and all Denso Models with 30mm bearing fit. Keep
More informationIMPORTANT SAFETY INFORMATION
Specifications Overall Dimensions Batteries 9" L x 6-3/4" W x 6-3/4" H 4 - AA (sold separately) IMPORTANT SAFETY INFORMATION Installation Precautions 1. Verify that installation surface has no hidden utility
More informationCold Shrink - Silicone Rubber QTII(X)4S-32H Series Cable Termination Instructions
Cold Shrink - Silicone Rubber QTII(X)4S-32H Series Cable Termination Instructions Class I Indoor Termination Voltage Designation: 12/20(24) kv Kit Contents: 1 HeatShrinkBreakoutBootAssembly 3 HeatShrinkBindingSleeves
More informationInstallation & Operation Manual. Electrak 1 Series / Electromechanical Linear Actuators Limit Switch, & Potentiometer Feedback, and Long Life Models
www..com Installation & Operation Manual Electrak 1 Series / Electromechanical Linear Actuators Limit Switch, & Potentiometer Feedback, and Long Life Models INTRODUCTION Thomson has many years of experience
More informationHI/LO CYLINDER (Y SERIES) INSTALLATION, OPERATING & MAINTENANCE MANUAL
HI/LO CYLINDER (Y SERIES) INSTALLATION, OPERATING & MAINTENANCE MANUAL 545 Hupp Avenue Jackson, Michigan 49204 Ph: 517-787-9444 Fx: 517-787-7585 www.airhydraulics.com info@airhydraulics.com Serial No.
More informationManual Operated Floor Jack
Manual Operated Floor Jack OPERATING INSTRUCTIONS Note: There may be some slight differences in the appearance of the various manually-operated floor jacks, however the instructions in this manual apply
More informationAtd Tools Inc. 160 Enterprise Drive, Wentzville, MO 63385
Owner's Manual Model RHO-7425 High Lift Transmission Jack Capacity 700 lbs.! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that
More informationOPERATIONS MANUAL MODEL MT-500
OPERATIONS MANUAL MODEL MT-500 Machine Serial Number: Specification Number: Engine Serial Number: SOLD & SERVICED BY SAFETY PRECAUTIONS AS STATED IN OSHA, THE EMPLOYER SHALL PERMIT ONLY THOSE EMPLOYEES
More informationOperators Manual. Model 3370 Air Cooled Recirculator rev.8/98
Operators Manual Model 3370 Air Cooled Recirculator 110-080 rev.8/98 Table of contents Section 1. General Information 1.1 Warranty 1.2 Unpacking Section 2. Product Information 2.1 Description 2.2 Specification
More informationInstructions. Quick Term II 2047MT 56. 3M Quick Term II. Silicone Rubber Termination (with High-K Stress Relief)
Instructions Quick Term II Silicone Rubber Termination (with High-K Stress Relief) IEEE Std. No. 48 990 Class Termination 5 kv Class 50 kv BIL Kit Contents Hi K Silicone Rubber Termination Scotch 70 Silicone
More information2012 Shop Presses & Accessories BUYERS GUIDE
2012 Shop Presses & Accessories BUYERS GUIDE MADE IN THE USA TM Equipping technicians with heavy-duty products Contents Press Features 2 25 Ton Shop Presses 3 50 Ton Shop Presses 4 100 Ton Shop Presses
More informationINSTALLATION AND MAINTENANCE MANUAL FORM #PM-126 REV A 12/09
HAND CRANK & MOTORIZED POWER CORD REELS: SERIES 1125PC SERIES: 1125PC HAND CRANK SERIES: 1125PC MOTORIZED COXREELS The technical data and images which appear in this manual are for informational purposes
More informationTECHNICAL SERVICE MANUAL
TECHNICAL SERVICE MANUAL VIKING HELICAL GEAR REDUCERS "A", "B", AND "C" SIZES SECTION TSM 610 PAGE 1 OF 9 ISSUE E CONTENTS Special Information 2 Lubrication 2 Installation 3 Operation 3 Disassembly 3 Assembly
More informationDEMON CARBURETOR MANUAL CHOKE KIT #421441
DEMON CARBURETOR MANUAL CHOKE KIT #421441 CHOKE INSTALLATION INSTRUCTIONS LIT703 This manual choke kit is designed to be used on any Demon Carburetor with a choke tower. This covers the Road Demon Jr.
More informationAir-Assist Service Jack Max. Capacity: 10 Tons
Form No. 565786 Parts List & Operating Instructions for: 1511B Air-Assist Service Jack Max. Capacity: 10 Tons 109 67 66 68 77 69 70 78 95 94 107 106 108 26 71 72 72 93 X L 65 75 92 91 90 89 88 87 86 85
More information12-1/4 x 3-1/2 Electric Wheel Brake
12-1/4 x 3-1/2 Electric Wheel Brake A-216 819-0244 Installation Instructions An Altra Industrial Motion Company Contents Dimensions.... 2 Technical Specifications.... 3 Installation Instructions General....
More informationPneumatic Cylinder 14 Bore X 21 Stroke Part No. P Replaces Part No. P
Pneumatic Cylinder 14 Bore X 21 Stroke Part No. P -322908-00000 Replaces Part No. P-191067-00000 Service Information WARNING: INSTALLATION AND MOUNTING The user of these devices must conform to all applicable
More informationHydraulic Air Pump. Operating Instructions & Parts Manual. Capacity 10,000 PSI. Model Number Atd-5812
Hydraulic Air Pump Operating Instructions & Parts Manual Model Number Atd-5812 Capacity 10,000 PSI Atd Tools Inc. 2005 160 Enterprise Drive, Wentzville, MO 63385 Atd5812-M0 Printed in Taiwan Save these
More informationOwner s Manual. Calcite ph Neutralizer
Owner s Manual Page 2 Copyright 2012 Enviro Water Solutions Inc. All rights reserved. All information contained herein is the property of Pelican Water Systems. Pelican Water Systems makes no warranty
More informationPack-Master Product Manual
Pack-Master Product Manual Jasper St., Unit F, Aurora, CO 80011 T 800.624.6706 F 303.364.7796 Newstripe.com Pack-Master Manual TABLE OF CONTENTS Precautionary Warning... Page 1 Assembly.. Page 2 Jack
More information