Drenth Motorsport Gearboxes. Figure 1: Rear and side view
|
|
- Jemimah Cobb
- 6 years ago
- Views:
Transcription
1
2 2 Drenth Motorsport Gearboxes Figure 1: Rear and side view
3 Introduction The Mitsubishi Lancer Evolution XI-IX 5-speed gearkit is specially designed for the group N rally. This unit fits the OEM Bell housing and the OEM cover of the gearbox. The Drenth Mitsubishi EVO VI - IX gearkit has proven itself in FIA Group N Rally, Hill Climbing, Rally Cross, Circuit use and Track days. The gearkit can handle torque levels up to 650 Nm. This document contains information about the EVO XI-IX gearkit. It is useful for everyone who is using or rebuilding a EVO XI-IX gearkit. The user manual includes illustrated parts list, a gearkit assembly, parts list and a gear ratio list. For more detailed information please contact Drenth Gearboxes. Drenth Motorsport Gearboxes Fleuweweg AG Enter The Netherlands Phone: +31 (0) Fax: +31 (0) Last modified: August 2015 info@drenth-gearboxes.com Made by Arjan Hoogendijk Mitsubishi EVO IX 3
4 4 Contents Introduction... 3 Contents Technical Specifications General Specifications Gears Overview Illustrated Parts List Layshaft Mainshaft Reverse shaft Differential Bell house and End cover bearings Shifting system Gearbox assembly General Instructions Notes Bearing assembly Main shaft bearing... 29
5 3.2.2 OEM Differential bearing Mainshaft bearing Layshaft bearing Main Assembly Step 3) Step 4) Run-in procedure Gear Ratio List Differential Bearing replacement Complete Parts List Contact Information Contact Information Address Contacts Sales department: Engineering: Mitsubishi EVO IX 5
6 1.0 Technical Specifications 6
7 1.1 General Specifications Max torque: 650 Nm Oil type: Castrol Syntrax Limited Slip Drenth Motorsport Gearboxes Oil quantity: 3.1 Liter for Gearbox / 0.6 Liter for Transfer Box Figure 2: Mitsubishi EVO IX Gearkit Mitsubishi EVO IX 7
8 8 1.2 Gears Overview Drenth Motorsport Gearboxes Figure 3: Gears overview
9 2.0 Illustrated Parts List Mitsubishi EVO IX 9
10 Layshaft Drenth Motorsport Gearboxes Figure 4: Layshaft
11 Layshaft Number QTY. Part Number Description Comments Layshaft (12-36 / 13-26) rd gear layshaft (17-25) th gear layshaft (18-20) th gear layshaft (28-24) Washer layshaft Circlip layshaft Layshaft bearing rear 8 3* 3* 3* Shim 63x80x0.1 Shim 63x80x0.3 Shim 63x80x1.0 * The Number of shims and the thicknesses are different in each gearbox because of minimal differences in dimensions of the bell housing and sleeve. Mitsubishi EVO IX 11
12 Mainshaft Drenth Motorsport Gearboxes Figure 5: Mainshaft
13 Mainshaft Number QTY. Part Number Description Comments ** Mainshaft (13-56) For different final drive see pag Needle bearing 1st gear st gear mainshaft Split ring Hub 1 st /2 nd gear Dogring 1 st /2 nd gear Old version: Please check part number on the part nd gear mainshaft (13-26) For different ratio s see pag rd gear mainshaft (17-25) For different ratio s see pag Hub 3 rd /4 th gear Dogring 3 rd /4 th gear th gear mainshaft (18-20) For different ratio s see pag th gear mainshaft (28-24) For different ratio s see pag Dogring 5 th /reverse gear Hub 5 th /reverse gear Inner track reverse gear Reverse gear mainshaft ( ) Inner track mainshaft Circlip mainshaft Mainshaft bearing (rear) 28 3* 3* 1* 1* Shim 60x72x0.1 Shim 60x72x0.3 Shim 60x72x1.0 Shim 60x72x Needle bearing 2 nd /3 rd /4 th /5 th gear Needle bearing reverse gear * The Number of shims and the thicknesses are different in each gearbox because of minimal differences in dimensions of the bell housing and sleeve. ** Depending on type of the gearbox is used. Mitsubishi EVO IX 13
14 14 Number QTY. Part Number Description 76* Mainshaft (13-56) *It is possible that the mainshaft nr. 76 is used is the old version, with steel sleeve is for in an stiffer housing. See also gearbox assembly from page 19.
15 2.3 Reverse shaft Drenth Motorsport Gearboxes Figure 6: Reverse shaft Mitsubishi EVO IX 15
16 16 Reverse shaft Number QTY. Part Number Description Comments Circlip OEM part Spring OEM part Trust washer OEM part Reverse idler Needle bearing OEM part Reverse shaft OEM part Ball reverse OEM part
17 2.4 Differential Drenth Motorsport Gearboxes Figure 7: Differential Mitsubishi EVO IX 17
18 18 Differential Number QTY. Part Number Description Comments Differential bearing (crown wheel side) OEM part Differential bolts M12x35 OEM part* Crown wheel (13-56) Differential complete OEM part Differential bearing OEM part * OEM bolt can be replaced with new bolts
19 2.5 Bell house and End cover bearings Drenth Motorsport Gearboxes Figure 8: Bearing placement Mitsubishi EVO IX 19
20 20 Bell house and End cover bearings Number QTY. Part Number Description Comments Layshaft bearing rear 8 3* 3* 3* Shim 63x80x0.1 Shim 63x80x0.3 Shim 63x80x Mainshaft bearing rear 28 6* 6* 2* 2* Shim 60x72x0.1 Shim 60x72x0.3 Shim 60x72x1.0 Shim 60x72x Differential bearing (crown wheel side) OEM part Differential bearing OEM part End cover OEM part Bell house OEM part Mainshaft bearing sleeve Ø72 mm Becomes nr. 66 when the bell housing is used Mainshaft bearing (front) Layshaft bearing (front) Oversized sleeve Ø72.5mm (used bell housing) Only for an used bell housing ** Mainshaft bearing front Only when you use mainshaft (nr. 76) * The Number of shims and the thicknesses are different in each gearbox because of minimal differences in dimensions of the bell housing and sleeve. **When you are using Mainshaft you need to use the mainshaft bearing (front) , you don t need the bearing sleeve (see picture in the centre below). See page 12 for the assembly of the mainshaft.
21 2.6 Shifting system Drenth Motorsport Gearboxes Figure 9: Shifting system Mitsubishi EVO IX 21
22 22 Shifting sytem Number QTY. Part Number Description Comments Spiral pin 5mm Selector fork 5 th /reverse gear Selector fork 3 rd /4 th gear Selector fork 1 st /2 nd gear Selector arm 5 th /reverse gear OEM part Selector arm 3 rd /4 th gear OEM part Selector arm 1 st /2 nd gear OEM part Selector fork shaft 5 th /reverse gear OEM part Selector fork shaft 3 rd /4 th gear OEM part Selector fork shaft 1 st /2 nd gear OEM part
23 2.7 Shifting tower Drenth Motorsport Gearboxes Figure 10: Shifting tower Mitsubishi EVO IX 23
24 24 Shifting tower ITEM NO PART NR QTY NAME PART Notes Interlocker Reverse lock plate OEM part Cover selector tower OEM part Rubber cover OEM part Spring OEM part Bolt M8 OEM part Main selector OEM part Spiral pin 5mm OEM part Selector shaft set OEM part Spring OEM part Pin OEM part Washer M8 OEM part
25 3.0 Gearbox assembly Mitsubishi EVO IX 25
26 General Instructions Notes First read the manual in general and check if all the parts are there. For an easy and faster assembly lay all the parts in the right order. Every part has got his own personal number. The number reference is shown in the parts list. Before the assembly all parts must be clean and undamaged. Also a clean tray is recommended Only genuine Drenth parts should be used when assembling and servicing this gearkit. For durability it s recommended to use new nuts, seals and circlips during the re-assembly of the gearbox. During the assembly only use lubrications that are recommended by Drenth Motorsports Gearboxes (Castrol Syntrax Limited Slip 75W 140).
27 3.2 Bearing assembly General information On the next page several illustrations are shown where each bearing needs to be placed. The bearings have got the same number as in Chapter 2 Illustrated Parts List. When the mainshaft (nr. 76) and bearing 75 are used, the housing does not need to be changed. Each bearing has to be slightly lubricated. Please note that not each bearing is assembled under heating conditions. To intercept the expansion due the heat, the bearings need to be adjusted with shims. This has to be done with bearing 7, 27 and 38. To determine the correct thickness of the shims see page 29 to 35. Bearing assembly: o The oven must be preheated. o Heat each section to a temperature of 100 / 110 C. o When the casing has reached this temperature, give it approximately 30 minutes to insure an even temperature distribution. o Before fitting the bearings make sure the outer track of the bearing is clean. o Once the casing is at the correct temperature and the bearings are clean, fit the bearings promptly and without delay. Try to avoid more heating cycles. Use a tool, for example a ring, which fits directly over the outer track of the bearing. o To avoid damage fit each bearing as straight as possible. o Heating conditions may not exceed 130 Celsius. Mitsubishi EVO IX 27
28 28 Drenth Motorsport Gearboxes Figure 11: Bearing assembly. (Only use bearing 75 when mainshaft (nr. 76) is used)
29 3.2.1 Main shaft bearing In the OEM gearbox the bearing fitting has a loose fit. When the gearbox reaches operation temperature, the aluminium housing expands more than the steel outer track of the bearing. Causing the outer track to turn in the housing and creating a bigger bearing fitting. After a certain time of race/ rally use, the bearing fitting becomes oversized and oval instead of circular. The solution for used housings is cutting the bearing fitting to 72.5 mm and fit it with a oversized steel sleeve (nr. 66, part nr ) with a smaller bearing than used before. New housings can be fitted with a standard steel sleeve (nr. 45, part nr ) and bearing without cutting the bearing fitting. Both steel sleeves have a tight fitting in the housing that prevents the bearings to turn. How this is done is described on the next few pages. Boring the used housing Originally the bearing fitting is 72 mm in diameter. If the housing is used and oval, it s recommended to make the bearing fitting circular again by cutting +0.5 mm in diameter. Cut the housing with the dimensions shown in the figure below. After cutting, the fitting must be 72.5 mm in diameter. The cutting dimension is tolerated: Drenth Motorsport Gearboxes Figure 12: Boring dimensions Mitsubishi EVO IX 29
30 30 Instruction notes: Make sure the bearings (nr. 46, 47 and outer track of bearing 42) and sleeve (nr. 45 or 66) are clean. The bearings (nr. 46, 47 and outer track of bearing 42) has to be slightly lubricated with oil. Press fit the bearing (nr. 46) and sleeve (nr. 45 or 66) together. Measure the distance from the mounting surface of the bell housing to the bottom of the bearing fitting. This distance must be 61.2 mm +/ (figure 12). If not, the distance can be adjusted with shims (nr. 28). The oven must be preheated. Heat the aluminium bell housing to a temperature of 100 / 110 C. Heating conditions may not exceed 130 Celsius. When the bell housing has reached this temperature, give it approximately 30 minutes to insure an even temperature distribution. Once the casing is at the correct temperature, fit the bearing with the sleeve promptly and without delay. Also fit bearing 47 and outer track of bearing 42 in the housing. Try to avoid more heating cycles. Final check if the distance between the mounting surface and the outer track of bearing. This distance must be / mm ± ± 0.05 Bearing and sleeve Number QTY. Part number Description Comments ** Mainshaft bearing front Normal sleeve 72 mm in diameter (new bell housing) Oversized sleeve 72,5 mm in diameter (used bell housing) 28 3* 3* 1* 1* Shim 60x72x0.1 Shim 60x72x0.3 Shim 60x72x1.0 Shim 60x72x2.0 Drenth Motorsport Gearboxes * The number of shims and thickness are different in each gearbox, because of minimal differences in dimensions of the bell housing and sleeve. Figure 13.1: Mounting dimensions
31 Instruction notes (Mainshaft ): Make sure the bearings (nr. 75, 47 and outer track of bearing 42) are clean. The bearings (nr. 75, 47 and outer track of bearing 42) has to be slightly lubricated with oil. Measure the distance from the mounting surface of the bell housing to the bottom of the bearing fitting. This distance must be 61.2 mm +/ (figure 12.1). If not, the distance can be adjusted with shims (nr. 28). The oven must be preheated. Heat the aluminium bell housing to a temperature of 100 / 110 C. Heating conditions may not exceed 130 Celsius. When the bell housing has reached this temperature, give it approximately 30 minutes to insure an even temperature distribution. Once the casing is at the correct temperature, fit the bearing promptly and without delay. Also fit bearing 47 and outer track of bearing 42 in the housing. Try to avoid more heating cycles. Final check if the distance between the mounting surface and the outer track of bearing. This distance must be / mm. Bearing and sleeve Number QTY. Part number Description Comments Mainshaft bearing front 28 3* 3* 1* 1* Shim 60x72x0.1 Shim 60x72x0.3 Shim 60x72x1.0 Shim 60x72x2.0 * The number of shims and thickness are different in each gearbox, because of minimal differences in dimensions of the bell housing and sleeve. In the rest of the manual the mainshaft (the most recent one) will be described. Drenth Motorsport Gearboxes Figure 13.2: Mounting dimensions Mitsubishi EVO IX 31
32 OEM Differential bearing Instruction notes: Bearing 42 and the differential must be assembled first (see previous step). Make sure the bearing (nr. 38) and shims (nr. 28) are clean. The bearing (nr. 38 and 42) has to be slightly lubricated with oil. To measure the distance that must be shimmed, put two pieces of solder (Ø2mm and 10mm in length) on top of the outer track over bearing 38. Then put the end cover on top of the bell housing and tighten the bolts (according to the specifications given on page 46) to make sure there is no clearance between the bell housing and end cover. Now take the end cover away and measure the crushed section of the pieces of solder. Preload on differential bearings must be mm. Thickness crushed solder + preload = thickness shims Place the calculated shims in the end cover, as pictured on page 28. Drenth Motorsport Gearboxes Figure 14: Differential bearing shim
33 3.2.3 Drenth Differential bearing Instruction notes: Bearing 77b, and the inner track of bearing 77a on the differential, must be assembled first. Make sure the bearing (nr. 77a) and shims (nr. 28) are clean. The bearing (nr. 99a) has to be slightly lubricated with oil. To measure the distance that must be shimmed, put two pieces of solder (Ø2mm and 10mm in length) on top of the outer track over bearing 99a. Then put the end cover on top of the bell housing and tighten the bolts (according to the specifications given on page 46) to make sure there is no clearance between the bell housing and end cover. Now take the end cover away and measure the crushed section of the pieces of solder. Thickness crushed solder - Free play = thickness shims Use no pre-load, always round down to the nearest thickness of a shim to make sure the free play is mm. Place the calculated shims in the end cover, as pictured on page 28. Check after shimming if the shaft runs free and if the differential has a free play of mm. Detail differential bearing Drenth Motorsport Gearboxes Figure 14.2: Drenth differential bearing shim Mitsubishi EVO IX 33
34 Mainshaft bearing Instruction notes: Bearing 46 and the main shaft must be assembled first. o For assemble instructions see pages 35 to 40. Make sure the bearing (nr. 27) and shims (nr. 28) are clean. The bearing (nr. 27) has to be slightly lubricated with oil. To measure the distance that must be shimmed, put shims in the end cover. Make sure there are enough shims, so you need only a small piece of solder on top of the outer track over bearing 27. Then put the end cover on top of the bell housing and tighten the bolts (according to the specifications given on page 46) to make sure there is no clearance between the bell housing and end cover. Now take the end cover away and measure the crushed section of the pieces of solder. Thickness crushed solder - Free play = thickness shims Use no pre-load, always round down to the nearest thickness of a shim to make sure the free play is mm. Place the calculated shims in the end cover, as pictured on page 28. Check after shimming if the shaft runs free. Drenth Motorsport Gearboxes Figure 15: Mainshaft bearing shim
35 3.2.5 Layshaft bearing Instruction notes: Bearing 47 and the lay shaft (nr. 1) must be assembled first. o For assemble instructions see pages 36 to 41. Make sure the bearing (nr. 7) and shims (nr. 8) are clean. The bearing (nr. 7) has to be slightly lubricated with oil. To measure the distance that must be shimmed, put shims in the end cover. Make sure there are enough shims, so you need only a small piece of solder on top of the outer track over bearing 27. Then put the end cover on top of the bell housing and tighten the bolts (according to the specifications given on page 46) to make sure there is no clearance between the bell housing and end cover. Now take the end cover away and measure the crushed section of the pieces of solder. Thickness crushed solder - Free play = thickness shims Use no pre-load, always round down to the nearest thickness of a shim to make sure the free play is mm. Place the calculated shims in the end cover, as pictured on page 28. Check after shimming if the shaft runs free. Drenth Motorsport Gearboxes Figure 16: Layshaft bearing shim Mitsubishi EVO IX 35
36 Main Assembly Step 1) Start with the bell housing (nr. 44). Fit the outer track of the differential bearing into the bell house (page 30). Press fit the differential bearings onto the differential. Slightly lubricate the differential bearings. Fit the crown wheel on the differential and tighten the bolts (nr. 39) with 132 Nm of torque and use loctite 270. Drenth Motorsport Gearboxes Figure 17: Step 1
37 Drenth Motorsport Gearboxes Figure 18: Step 2 Mitsubishi EVO IX 37
38 38 Step 2) For step 2 the layshaft and Mainshaft are used as a base for further assembly. Each bearing (10, 29 and the Mainshaft bearing) has to be slightly lubricated. The assembly sequence: o First place the mainshaft (9/76) into the bearing in the bell housing. o Now place the bearing (10), the first gear (11) and the split ring (12, 2x) over the mainshaft. o The hub (13) and dog ring (14) slide over each other and fit over the mainshaft. Make sure the inner spline of the dog ring fits correctly over the outer spline of the hub (see picture below). o Place the bearing (29) and second gear (15) over the mainshaft. o At last place layshaft (1) in the bearing (47). Drenth Motorsport Gearboxes Figure 19: Dogring placement
39 Drenth Motorsport Gearboxes Figure 20: Step 3 Mitsubishi EVO IX 39
40 40 Step 3) During this step the 3 rd 4 th and 5 th gear are assembled. The three needle bearings (29) must be slightly lubricated. Place all the parts in the order which is given on the exploded view on the page above. Make sure the inner spline of the dog ring (18 and 22) fits correctly over the outer spline of the hub (17 and 21). Finish this step by putting the circlip (6) over the layshaft. Drenth Motorsport Gearboxes Figure 21: Dogring placement
41 Drenth Motorsport Gearboxes Figure 22: Step 4 Mitsubishi EVO IX 41
42 42 Step 4) During this step the reverse gear is assembled. Needle bearing (30) has to be slightly lubricated. Press-fit inner track (23) on the mainshaft. o Assemble bearing (30) and reverse gear (24). Press-fit inner track (25) on the mainshaft. Finish this step by putting the circlip (26) over the main shaft.
43 Drenth Motorsport Gearboxes Figure 23: Step 5 Mitsubishi EVO IX 43
44 44 Step 5) During this step the selector system is assembled into the bell housing. Place the selector forks (49, 50 and 51) over the dogrings on the Mainshaft. Place the selector fork shafts (55, 56 and 57) through the selector forks and the selector arms (52, 53 and 54) into the bell housing. Put the spiral pins (48) trough the selector forks, the selector shafts and the selector arms. o Check if all pins fit in tight, due to vibrations the pins can come out and cause damage to the gearbox. o Also check if the selectors (nr. 52, 53 & 54) are in one line. Drenth Motorsport Gearboxes Figure 24: Selector system
45 Drenth Motorsport Gearboxes Figure 25: Step 6 Mitsubishi EVO IX 45
46 46 Step 6) During this step the end cover is assembled on the bell housing to enclose the gearbox Before assembling the end cover (nr. 43), the dowels (nr. 67 and 68) need to be placed. To secure the end cover, use the original bolts (nr. 69). Tighten the 15 original bolts (M10x40) with 44 Nm. Drenth Motorsport Gearboxes Figure 26: Assembled bell housing
47 Step 7) During this step the shifting tower is assembled onto the gearbox. For the assembly sequence of the selector shaft see page 23 & 24. Use sealant to seal the shifting tower plate. Put the gearshift system into the gearbox and align the fingers in the selectors. Tighten the original bolts with 30Nm. Drenth Motorsport Gearboxes Figure 27: Shifting tower Mitsubishi EVO IX 47
48 48 Drenth Motorsport Gearboxes Figure 28.2: OEM gearbox cover Drenth Motorsport Gearboxes Figure 28.1: Step 8
49 Step 8) During this step we assemble the reverse gear. Needle bearing (nr. 35) has to be slightly lubricated. Place all parts in the order which is given on the exploded view on this page. o Make sure that the ball (nr. 37) fits properly in the spacer (nr. 33) and in the shaft (nr. 36). Now place the assembled reverse gear in the housing and secure the bolt (nr. 72) with 50Nm. Mount the OEM gearbox cover (see figure 27.1, nr. 73) in its place using the OEM bolts (M6x10, nr. 74) tighten it with 14 Nm and use silicone sealant to prevent leakage. Finally turn the oil plug (nr. 70) in the housing with 20 Nm. Drenth Motorsport Gearboxes Figure 29: Reverse gear Mitsubishi EVO IX 49
50 Run-in procedure Run through the gears while the gearbox is not mounted underneath the car. Make sure that the layshaft rotates smoothly. When this is working and the oil level is correct, the gearbox can be mounted on a test bench or underneath the car. For the first test the wheels should be tilted from the ground. Before the test run make sure the gearbox is in the neutral position. During the test run go through all the gears in a low rpm range. Stay on low rpm until the gearbox is warmed-up. After warm-up check all gearshifts. During the run also concentrate on noise production, vibrations and the temperature. When one of them is out of the ordinary, stop the test and locate the problem. After the first test the gearbox is ready for a test drive. The procedure is the same as the first test. Slowly build-up the engine rpm and torque when the temperature level starts to increase. During the warm-up of the gearbox don t warm-up the brakes.
51 4.0 Gear Ratio List Homologated gear ratio (FIA Group N) 1 st gear 2 nd gear 3 rd gear 4 th gear 5 th gear Final drive Gear ratio s available for Hillclimb, Rallycross and Time attack. Different Layshafts Available (with fixed gears) Free to choose 3 rd Free to choose 4 th Free to choose 5 th gears gears gears 1 st gear 2 nd gear 3 rd gear 3 rd gear 4 th gear 5 th gear Other final drive ratios Different gear ratios are available on request Ratio requests from customers will be added to the list In consultation with the customer the ideal ratios can be calculated Mitsubishi EVO IX 51
52 Differential Bearing replacement Due the straight cut teeth profile there are no axial forces. Therefore the tapered roller bearing are no longer specifically needed and can be replaced with new cylindrical roller bearings. These bearings are specifically engineered and fabricated for the Drenth EVO XI-IX Group N. When replacing the standard differential bearings, the Drenth cylindrical roller bearings must be mounted according to chapter 3.2 (Bearing Assembly). These bearings must be adjusted with shims but don t need to be pre-loaded. For a detailed description of the mounting instructions please see page 33. The new differential bearings are available as a set of the two bearings with adjusting shims. For more information about the bearings please contact our sales department. Differential Bearing replacement Number QTY. Part Description number Roller bearing set (included shims) 77a Differential bearing (crown wheel side) 77b Differential bearing (bell housing) Drenth Motorsport Gearboxes Figure 30: Differential Bearing upgrade
53 6.0 Complete Parts List Mitsubishi EVO IX 53
54 54 Number QTY. Part Number Description Number QTY. Part Number Description Layshaft (12-36 / 13-26) Inner track reverse gear Reverse gear mainshaft ( rd gear layshaft (17-25) ) th gear layshaft (18-20) Inner track mainshaft th gear layshaft (28-24) Circlip mainshaft Washer layshaft Mainshaft bearing (rear) Circlip layshaft 28 6* 6* 2* 2* Shim 60x72x0.1 Shim 60x72x0.3 Shim 60x72x1.0 Shim 60x72x Layshaft bearing rear Needle bearing 2 nd /3 rd /4 th /5 th gear 8 3* 3* 3* Shim 63x80x0.1 Shim 63x80x0.3 Shim 63x80x Needle bearing reverse gear Mainshaft (13-56) * Circlip Needle bearing 1st gear * Spring st gear mainshaft * Trust washer Split ring Reverse idler Hub 1 st /2 nd gear * Needle bearing Dogring 1 st /2 nd gear * Reverse shaft nd gear mainshaft (13-26) * Ball reverse Differential bearing (crown rd gear mainshaft (17-25) * wheel side) Hub 3 rd /4 th gear * Differential bolts M12x Dogring 3 rd /4 th gear Crown wheel (13-56) th gear mainshaft (18-20) * Differential complete th gear mainshaft (28-24) * Differential bearing Dogring 5 th /reverse gear * End cover Hub 5 th /reverse gear * Bell house
55 Number QTY. Part Number Description Number QTY. Part Number Description Mainshaft bearing sleeve Ø72 mm Rubber cover Mainshaft bearing (front) * Selector lever Layshaft bearing (front) * Selector finger Oversized sleeve Ø72.5mm Spiral pin 5mm (used bell housing) Selector fork 5 th /reverse gear * Dowel 10x Selector fork 3 rd /4 th gear Dowel 10x Selector fork 1 st /2 nd gear * Bolts M10x * Selector arm 5 th /reverse gear * Oil plug * Selector arm 3 rd /4 th gear * washer * Selector arm 1 st /2 nd gear * Reverse bolt * Selector fork shaft 5 th /reverse gear * Gearbox cover * Selector fork shaft 3 rd /4 th gear * Bolt M6x * Selector fork shaft 1 st /2 nd gear Mainshaft bearing front Interlocker Mainshaft (13-56) Differential bearing (crown 77a * Main selector wheel side) Roller bearing set (included * Spring shims) Differential bearing (bell 77b * Main selector shaft housing) * Cover selector tower * OEM parts Mitsubishi EVO IX 55
56 7.0 Contact Information 56
57 7.0 Contact Information Address Drenth Motorsport Gearboxes Fleuweweg AG Enter The Netherlands Phone: +31 (0) Fax: +31 (0) Contacts Sales department: Johan Drenth Engineering: Jeroen Grolleman 57 Mitsubishi EVO IX
58 58
Introduction. We will strongly recommend that the gearbox will be assembled by skilled technicians.
25.03.0032 Introduction The Drenth Gearbox 350 (DG350) sequential racing gearbox is originally developed for the Toyota GT86, but due its design specifications it fits into almost any rear wheel driven
More informationIntroduction. Drenth Motorsport Gearboxes Fleuweweg AG Enter The Netherlands Phone: +31 (0) Fax: +31 (0) DG400
25.03.0025 Introduction The Drenth Gearbox 400 () 6-speed sequential racing gearbox is designed to be used in motorsport. Due to its compact design it fits into nearly any rear wheel driven car. The is
More informationHOLINGER SF GEARBOX MANUAL
HOLINGER SF GEARBOX MANUAL Approved By: Leigh Nash Date: 26/05/2011 Rev: D Date: 11/11 Holinger Engineering Gearbox Manual Page 1 FOREWORD The Holinger SF is a sequential-shift transaxle designed for use
More informationMANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed
IDENTIFICATION MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED 1998 MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed Transmission has 2 identification labels, located on lower left side of case. One
More informationW5M51. Maintenance Manual MANUAL TRANSMISSION CONTENTS
Maintenance Manual W5M51 MANUAL TRANSMISSION FOREWORD This manual explains the maintenance procedures for the W5M51 manual transmission on the 2003 Lancer Evolution VIII, but only for points which differ
More informationHOLINGER RD6-S GEARBOX MANUAL
HOLINGER RD6-S GEARBOX MANUAL Rev A. Date: 03/11 Holinger Engineering Gearbox Manual Page 1 FOREWORD The Holinger RD6-S is a sequential-shift dog-change gearbox primarily designed for use in front-engine,
More informationThe 6-Speed Manual Gearbox 08D
Service. Self-Study Programme 299 The 6-Speed Manual Gearbox 08D Design and Function The Touareg is an exclusive cross country vehicle with the driving properties and driving comfort of a sporty luxury
More informationNOVARACING TRANSMISSIONS LTD
NOVARACING TRANSMISSIONS LTD MANUFACTURERS OF 6 PINNACLE CLOSE, PHOENIX LANE TRANSMISSION SYSTEMS CROWLAND, LINCS, PE6 OGB,UK. FOR RACING AND Company Reg: 2438157 Cardiff DEVELOPMENT VAT NO. 550-6594-34
More informationMTMANUAL TRANSMISSION GENERAL 1. SPECIFICATIONS. 1) General Specifications. 2) Tightening Torque MANUAL TRANSMISSION
03-3 MT GENERAL 1. SPECIFICATIONS 1) General Specifications 2) Tightening Torque 03-4 OVERVIEW AND OPERATION PROCESS 1. OVERVIEW 4WD Features 1. All gears use the helical type and high strength materials.
More informationTransmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
More informationIllustrated Parts List
Illustrated Parts List ZY05289 March 202 Contents How To Use The Illustrated Parts List... 3 AIR SYSTEM... 4 CLUTCH ASSEMBLY... 5 CLUTCH SERVO ASSEMBLY... 6 FRONT BEARING COVER ASSY.... 7 FRONT CASE ASSY...
More informationTransfer Type Transmission Type Item
60 CHASSIS HF2AV TRANSFER HF2AV TRANSFER DESCRIPTION The LX 450 uses HF2AV type full time 2 speed transfer in which a center differential is enclosed. The center differential is equipped with a viscous
More informationMANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
More informationTSM54/52 MANUAL TRANSMISSION
3B-1 SECTION 00 3B TSM54/52 MANUAL TRANSMISSION Table of Contents GENERAL INFORMATION... 3B-3 Overview... 3B-3 Specifications... 3B-4 System components... 3B-5 Shifting mechanism... 3B-17 Diagnostic information
More information1994 Mitsubishi Eclipse GS
APPLICATIONS CHRYSLER MOTORS MANUAL TRANS OVERHAUL - MITSUBISHI W5M & W6M SERIES MANUAL TRANSMISSIONS Mitsubishi W5M31, TRANSMISSION APPLICATIONS (CHRYSLER MOTORS) Vehicle Application Transmission Model
More informationMANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series TRANSMISSION APPLICATION
Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series APPLICATION TRANSMISSION APPLICATION Vehicle Application Transmission Model Chrysler Motors (2WD) 4-Speed
More informationTransmission, disassembling and assembling
Page 1 of 27 34-43 Transmission, disassembling and assembling Disassembly sequence Page 34-55. Transmission overview 1-1st gear 2-2nd gear 3-3rd gear 4-4th gear 5-5th gear 6 - Reverse gear Removing and
More informationIntroduction. Drenth Motorsport Gearboxes Fleuweweg AG Enter The Netherlands Phone: +31 (0) Fax: +31 (0)
25.03.0023 Introduction The display unit comes with a software application. With the software application information shown on the display can be adjusted. There are different modes to adjust: the shape
More informationRemanufactured Transmissions, Spare Parts, and Kits Catalog
S6-650 Spare Parts - Gearbox Housing Group 01.010 1319 301 025 Main Housing without Check Valve 005/006/045/046/049/050 1319 301 093 Main Housing without Check Valve 083/085/084/086 1319 301 084 Main Housing
More informationSECTION B Manual Transaxle/Transmission TR6060
308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2
More informationRepair Manual VW 02J gearbox. INA GearBOX
Repair Manual VW 02J gearbox INA GearBOX Special tools Pipe section, 50 mm: Press fitting of synchronizer body for third/fourth gear. Assembly of support bearing for input and output shaft. Part number:
More informationPage 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step 5. 1. Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B
More information26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) DUAL RANGE HIGH SPEED INSTALLATION MANUAL. for
26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DUAL RANGE HIGH SPEED INSTALLATION MANUAL for TOYOTA
More informationThis guide gives a step-by-step guide to fitting the Nova BSA Goldstar 5 Speed Gearbox
MANUFACTURERS OF TRANSMISSION SYSTEMS FOR RACING AND DEVELOPMENT Unit 12 Star Industrial Estate, Star Road Partridge Green, West Sussex, RH13 8RA, UK. Company Reg: 2438157 Cardiff VAT NO. 550-6594-34 Registered
More informationY08521 September 2014
Y0852 September 204 Contents How To Use The Illustrated Parts List... 3 FRONT BEARING COVER ASSY.... 4 FRONT CASE ASSY... 5 INPUT SHAFT ASSY... 7 INTERMEDIATE CASE ASSY... 8 LAYSHAFT ASSY.... 0 LRC ASSEMBLY...
More information1. Spare Parts List 1.1 Preface The spare parts list is only valid for the type and versions of transmission, as shown below. You will find the transm
S P A R E P A R T S L I S T A N D E X P L O S I O N V I E W P A S C A T A L O G U E R T R E A S P ZF 15 MIV (HBW 150 V) Cod. 310.01.0100 1. Spare Parts List 1.1 Preface The spare parts list is only valid
More information. SERVICE DIVISION ID JD EALEJR IJRAINING G.J AI D # S ' MODEL: SU BJ Eel: GEARBOX \"')~.". BRITISH L.EYL.ANC L.EYL.
-. " 'J.' ('-. '...... 'i I - ' :' \"').". ::,: -:'"" T."..!--. 1- ',", BRITISH V. I "\' L.EYL.ANC L.EYL.ANO. SERVICE DIVISION ID JD EALEJR IJRAINING < -:' AI D # 81016 S1016 -.' I J SU BJ Eel: GEARBOX
More informationY07121 November 2015
Y072 November 205 Contents How To Use The Illustrated Parts List... 3 FRONT BEARING COVER ASSY.... 4 FRONT CASE ASSY... 5 INPUT SHAFT ASSY... 7 INTEGRATED AIR SYSTEM... 8 INTERMEDIATE CASE ASSY.... 0 LAYSHAFT
More informationLoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case
LoMax 205 CASE & 3:1 GEAR SET Part No. 2800 Instruction Rev: 2007.08.16 Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case Kit Components: 1. (1) 42x25
More informationRemanufactured Transmissions, Spare Parts, and Kits Catalog
S5-42 Spare Parts - Gearbox Housing Group 01.010 1307 201 005 Main Housing 050/051/064/118 1307 201 076 Main Housing 056/057/059/100/102/103/108/109/110/111 1307 201 080 Main Housing 053/054/120 01.012
More informationMANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34
MANUAL TRANSAXLE SECTIONMT GI MA EM LC EC CONTENTS FE PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
More informationRemanufactured Transmissions, Spare Parts, and Kits Catalog
S5-47M Spare Parts Gearbox Housing Group 01.010 1317 301 016 Main Housing All 01.018 0501 202 797 Breather All 01.026 1319 301 012 Oil Feeder All 01.030 1317 301 017 Rear Housing 4x2 014/016/020 1317 301
More informationOutput Shaft Assembly COMPONENTS
MT140 Component Parts (Output Shaft Assembly Output Shaft Assembly COMPONENTS DISASSEMBLY OF OUTPUT SHAFT ASSEMBLY 1. REMOVE SLEEVE FROM OUTPUT SHAFT Using SST, remove the sleeve from the output shaft.
More informationSECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS
SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS General Description and Operation... 5B-2 Shift Lever... 5B-2 Transmission Assembly... 5B-2 Specifications... 5B-3 Diagnostic Information and Procedures...
More informationTRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH
TRANSFER CASE 1993 Mitsubishi Montero 1991-94 TRANSFER CASES Mitsubishi Dodge; Ram-50 Mitsubishi; Pickup, Montero APPLICATION TRANSFER CASE APPLICATIONS TABLE Application (1) Transmission Model Dodge 1991-93
More information1. General Description
1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh
More information1. General Description
1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final
More informationGear Products Inc N. 161st E. Ave. Tulsa, OK Phone (918) Fax (918)
SERVICE MANUAL Disassembly & Assembly Procedures Worm Gear Swing Drive 003 Series Gear Products Inc. 1111 N. 161st E. Ave. Tulsa, OK 74116 Phone (918) 234-3044 Fax (918) 234-3455 Worm Gear Swing Drive
More informationFS V5206A RH. Z32639 Illustrated Parts List. May 2009 Issue 01 BOM date Eaton Corporation. All rights reserved.
FS V5206A RH Z32639 Illustrated Parts List May 2009 Issue 01 BOM date 06.05.2009 2007 Eaton Corporation. All rights reserved. Table of contents How to use the Illustrated Parts List Transmission Identification
More informationAUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE
Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista
More informationTransmission Overhaul Procedures-Bench Service
How to Install the Auxiliary Countershaft Assembly Special Instructions To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12" piece of wood. 3' 1' 3" 4.56"
More informationSECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE
SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE CAUTION: This vehicle will be equipped with a Supplemental Restraint System (SRS). An SRS will consist of either seat belt pre-tensioners and a driver's
More information4-50 BRAKES AND STEERING CLUTCHES
4-50 BRAKES AND STEERING CLUTCHES Disassembly of bevel gear crown WARNING Lift and handle all heavy items with a hoist of appropriate capacity. Make sure that all parts are held by appropriate slings and
More informationFinal Drive. Cush Drive SelVice Manual- Thunderbird. Inspection Note: Removal. Installation. 1. Remove the rear wheel (see page 76-8>.
Inspection Note: If the drive belt is to be renewed, always check and if necessary replace the rear belt pulley drive flange bearings. 1. Inspect the drive belt for wear, cracks in the teeth, frayed edges
More informationMaintenance Manual MM-0194 Single reduction leading axle carrier for tandem axle series MD61. Revised September 2017
Maintenance Manual MM-0194 Single reduction leading axle carrier for tandem axle series MD61 Revised September 2017 Service Notes Before You Begin This publication provides installation and maintenance
More information26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for
26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DEDICATED LOW RANGE INSTALLATION MANUAL for TOYOTA
More informationOVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.
41135 OVERHAUL 4108901 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 0.40 mm (0.0039 0.0157 in.) C68252 2. INSPECT 2ND GEAR THRUST CLEARANCE
More informationUSER MANUAL. D. Transmission
USER MANUAL D. Transmission CONTENTS 1. CLUTCH...4 1.1. Description... 4 1.2. Tightening torques... 5 1.3. Installation and removal... 5 1.3.1. Installation... 5 1.3.2. Removal... 5 1.4. Releaser... 5
More informationPage 02: Decalls. Page 03: Covers
Parts manual Redexim Verti-Drain / Pag Code Page : Decalls TM Page : Covers Page : Rear roller Page : Front roller Page : Element VD-PP INDEX.dwg Redexim Verti-Drain / Pag Code Page : Crankshaft TM Page
More informationMANUAL TRANSMISSION F5M41, F5M42, W5M42 CONTENTS GENERAL INFORMATION 1. SPECIFICATIONS... 22B-1-1 TRANSMISSION MODEL TABLE
22B-0-1 MANUAL TRANSMISSION F5M41, F5M42, W5M42 GENERAL INFORMATION........................................... 22B-0-3 1. SPECIFICATIONS................................................. 22B-1-1 TRANSMISSION
More informationGroup 1: Gearbox housing
1 Five-Speed gearbox crown wheel 11 Nylon socket for speed- 21 Screw 31 Tube 2 Plug 12 Cup 22 Screw 32 Deflector 3 Gearbox and clutch housing 13 Pinion f. speedometer 23 Screw 33 s 4 Front cover 14 Stop
More informationSUZUKI SQ 416/420/625 M.Y TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS
SUZUKI SQ 416/420/625 M.Y 1998-2005 TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS WARNING/CAUTION/NOTE IMPORTANT Please read this manual and follow its instructions carefully.
More informationFinal drive gear set, recommended sequence for adjusting
Page 1 of 31 39-148 Final drive gear set, recommended sequence for adjusting If the pinion shaft and ring gear have to be readjusted, the following sequence is recommended for maximum efficiency: 1.) Determine
More informationBORG WARNER TRANSFER BOX
BORG WARNER TRANSFER BOX Overhaul Manual BORG WARNER 44-62 TRANSFER BOX OVERHAUL MANUAL This transfer box is used on the following models: New Range Rover Published by Rover Technical Communication 1996
More information1. Set the position of the hub to FREE and remove the six hex-drive bolts.
1. Raise vehicle on a hoist, remove road wheels, disconnect the drag-link from the passenger-side hub assembly and disconnect the steering tie rod ends from both the driver and passenger side hub assemblies.
More informationInstruction Manual for HSPA Take-Up Units
Installation Instruction Manual for HSPA Take-Up Units Warning: To ensure the drive is not unexpectedly started, turn off and lockout the power source before proceeding. Failure to observe these precautions
More informationMANUAL TRANSMISSION SERVICE
MANUAL TRANSMISSION SERVICE Introduction Internal combustion engines develop very little torque or power at low rpm. This is especially obvious when you try to start out in direct drive, 4th gear in a
More informationIllustrated Parts List
Illustrated Parts List Y04392 JUNE 203 CONTENTS HOW TO USE THE ILLUSTRATED S LIST 3 FRONT BEARING COVER ASSY 4 FRONT CASE ASSY 5 INPUT SHAFT ASSY 7 LAYSHAFT ASSY 8 LRC ASSEBLY 9 AINSHAFT ASSY REAR CASE
More informationDRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
More informationSERVICING INSTRUCTIONS AND ILLUSTRATED PARTS LIST FOR HEWLAND MLG GEARBOXES
SERVICING INSTRUCTIONS AND ILLUSTRATED PARTS LIST FOR HEWLAND MLG GEARBOXES HEWLAND ENGINEERING LTD, WALTHAM ROAD, WHITE WALTHAM, MAIDENHEAD, BERKSHIRE, SL6 3LR, ENGLAND LAST REVISION:- 23rd December 2013
More informationINTRODUCTION. Ensure all works tools are in good condition and only use the correct tool for the job in hand.
NEWAGE 9TRA GEARBOX WORKSHOP MANUAL WINGET LIMITED PO BOX 4 EDGEFOLD INDUSTRIAL ESTATE PLODDER LANE BOLTON LANCS BL4 OLS TEL ++ 44 (0) 04 854650 FAX ++ 44 (0) 04 85466 E mail service@winget.co.uk parts@winget.co.uk
More informationDrive pinion and ring gear,
Page 1 of 38 39-166 Drive pinion and ring gear, adjusting General notes: Drive pinion and ring gear must be very carefully adjusted to ensure long service life and smooth running. At the factory, drive
More informationMaintenance Manual FP-330 Drive Gear
Maintenance Manual FP-330 Drive Gear Sisu Axles, Inc. Autotehtaantie 1 P.O. Box 189 FIN-13101 Hämeenlinna Finland Phone int + 358 204 55 2999 Fax int + 358 204 55 2900 FP330DG 2/2008 Maintenance Manual
More informationMaintenance Instructions
General Note These instructions contain information common to more than one model of Bevel Gear Drive. To simplify reading, similar models have been grouped as follows: GROUP 1 Models 11, 0, 1,, (illustrated),,
More informationVehicle: Year/Prod. Date: Engine Transmission:
WORKSHEET 4-2 Transaxle Shaft Removal and Inspection Vehicle: Year/Prod. Date: Engine Transmission: Worksheet Objectives With this worksheet, you will follow the disassembly of a front-drive transmission
More informationDRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
More informationLuK Repair Solution for manual transmissions. Disassembly and assembly Special tool/failure diagnosis VW 02J
LuK Repair Solution for manual transmissions Disassembly and assembly Special tool/failure diagnosis VW 02J The content of this brochure shall not be legally binding and is for information purposes only.
More informationReturn to Instruction Sheet index. Installation Instructions For C-4 70 and Later, Except 70 Falcon
Page 1 of 8 Return to Instruction Sheet index TCI 260100 Trans-Scat Automatic Transmission Installation Instructions For C-4 70 and Later, Except 70 Falcon TCI 260100 Kit Contains: Qty. Description One
More informationRedexim-Charterhouse Verti-Drain 7110 pag 01 code 0805
0 9 0 9 0 Redexim-Charterhouse Verti-Drain 0 pag 0 code 00 9.09. Main frame VD 0..0 Spring washer M 0..0 Bolt M x..9 Gearbox Comer T-A, 9.00 0..900 Bolt M x 90.0.0 Large washer M 0.0.0 Self lock nut M.00.00
More informationInstructions to install the early ( ) Limited Slip Differential in the Late-model ( ) G28 Transaxle
Instructions to install the early (1978-83) Limited Slip Differential in the Late-model (1985-1995) G28 Transaxle BACKGROUND: Most 928 owners know about the improvements to the 5- speed transaxle that
More informationReverse Idler Gear Shaft
«1993 Thunderbird/Cougar Table of Contents» «Group 07: TRANSMISSION» «Section 07-03: Transmission, Manual--M5R2» «DISASSEMBLY AND ASSEMBLY» Reverse Idler Gear Shaft Disassembly Remove the following parts
More informationDevelopment of Seamless Shift for Formula One Car
Development of Seamless Shift for Formula One Car Takashi YOSHIOKA* Katsumi KUBO* Takeshi UCHIYAMA* Ryo MATSUI* ABSTRACT Honda focused on gearbox development during its third Formula One era. The reduction
More informationSISU MP-330 DRIVE GEAR. Maintenance Manual
SISU MP-330 DRIVE GEAR Maintenance Manual Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 Fin-13101 Hameenlinna Finland Phone +358 204 55 2999 Fax +358 204 55 2900 MP330DG.PDF (4/2007) TABLE OF CONTENTS
More informationINSTRUCTIONS FOR USE SPUR GEAR OPERATORS. E. EBONG issue 4 SPUR
INSTRUCTIONS FOR USE GEAR OPERATORS Spur Range Specification: Installation, Operating and Maintenance Instructions: Assembly and Dismantling Instructions: Spare Parts List and Recommended 5 Years Holding
More informationMANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13
TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Service Notice or Precaution...2 PREPARATION... 3 Special Service Tool...3 Commercial
More informationIllustrated Parts List
More time on the road Illustrated s List FS-4205B November 2012 Contents How To Use The Illustrated s List... CASE... 4 COUNTERSHAFT ASSY... 8 INPUT SHAFT... 9 KITS & ASSEMBLIES... 11 LEVER ASSY... 1 MAINSHAFT
More informationRepairs after which the ring gear must be adjusted Page Drift VW 295
Page 1 of 15 39-52 Ring gear, adjusting (Adjusting differential) Repairs after which the ring gear must be adjusted Page 39-37. Special tools, testers and auxiliary items Drift VW 295 Dial gauge extension
More informationG85CS Parts list. Frank Kyul, Netherlands
G85CS Parts list Frank Kyul, Netherlands http://home.wanadoo.nl/fxkuyl/ CYLINDER BARREL & HEAD 022298 Barrel Cylinder 1 022515 Washer Cylinder Base 1 015351 Nut. Sleeve Cylinder Head 4 042157 Washer Sleeve
More informationMANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2)
MANUAL TRANSMISSION 7B 1 RODEO TRANSMISSION MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) CONTENTS Service Precaution...................... 7B 2 General Description..................... 7B
More informationSISU DP-330 DRIVE GEAR. Maintenance Manual
SISU DP-330 DRIVE GEAR Maintenance Manual Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 Fin-13101 Hameenlinna Finland Phone +358 204 55 2999 Fax +358 204 55 2900 DP330DG.PDF (3/2007) TABLE OF CONTENTS
More informationTRANSMISSION AND TRANSFER CASE
DR TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page MANUAL TRANSMISSION- G56- SERVICE INFORMATION...1 MANUAL TRANSMISSION- GETRAG 238- SERVICEINFORMATION...69 MANUAL
More informationMANUAL TRANSMISSION SECTION MT CONTENTS C TRANSMISSION/TRANSAXLE MT-1 FS5R30A FS6R31A
C TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E FS5R30A PRECAUTIONS... 3 Service Notice or Precautions... 3 PREPARATION... 4 Special Service Tools... 4 Commercial Service Tool...
More informationSupplement to Spare Parts Catalogue. Model : FT Dual Transmission - F
Supplement to Spare Parts Catalogue Model : FT - 60 Dual Transmission - F10001760 CONTENTS Tab. No. Sheet No. DESCRIPTION Page No. 1 101764-8 HEAD LIGHT, REAR LIGHT AND PLOUGH 1 LAMP 2 101766A-7 SHEET
More informationInstruction Manual for PTI Split Block Bearing Units For SAF, SDAF, SN, SNG, SNHF, S3000K & SD Series Housings
Instruction Manual for PTI Split Block Bearing Units For SAF, SDAF, SN, SNG, SNHF, S3000K & SD Series Housings Installation SDAF SD & S3000 SAF Warning: To ensure that the drive is not unexpectedly started,
More information1. Set the position of the hub to FREE and remove the six hex-drive bolts.
1. Raise vehicle on a hoist, remove road wheels, disconnect the drag-link from the passenger-side hub assembly and disconnect the steering tie rod ends from both the driver and passenger side hub assemblies.
More informationBag 1. Bag 1. Center Pivot. Center Pivot
8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball
More informationMANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. Case Components...27
MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
More information250P Manure Spreader
0P Manure Spreader Illustrated Parts Breakdown Page - Page Page Page Page Page Page Page Page Page Page Page Page Page Page - Page Page Page 0 Complete Front End PTO/Jack/Hitch Assembly Front Pulley Assembly
More informationWORKSHEET 4-1 Transaxle Case Removal and Component Identification
WORKSHEET 4-1 Transaxle Case Removal and Component Identification Vehicle: Year/Prod. Date: Engine Transmission: Worksheet Objectives With this worksheet, you will follow the disassembly of a front-drive
More informationParts List PL_TR-TO-10_0714
Torque Transfer Solutions TR-TO-10 Series 10-Speed Twin Counter Shaft Manual Transmission Parts List PL_TR-TO-10_0714 14700 Helm Ct. Plymouth, MI 48170 U.S.A. (800) 401-9866 www.tremec.com Copyright 2014
More informationSPICER. WEATHERLYINDEX084 T21 O-ES70-5 October 1993 ES70-5 Series Main Transmission
SPICER WEATHERLYINDEX084 T2 O-ES70-5 October 993 ES70-5 Series Main Transmission ES70-5 Series Main Transmission For parts or service call us Pro Gear & Transmission, Inc. (877) 776-4600 (407) 872-90 parts@eprogear.com
More information2001 F-650/750 Workshop Manual
26. Pack the reverse idler gear bearings with lubricant. Use Moly number 2 lubricant or equivalent. 27. Install the following: 1. Assemble the reverse idler gear and bearings onto the idler shaft. 2. Position
More informationParts made by people who race and know what it is about
RACING TRANSMISSIONS / 840 SERIES The 840 series has been one of the best options for front engine-rear wheel drive racing cars with4/6 cylinder engines since 1975; formerly, with the TC models, and at
More informationIllustrated Parts List
More time on the road Illustrated s List FS-5005A November 2012 Contents How To Use The Illustrated s List... CASE... 4 COUNTERSHAFT ASSY... 8 INPUT SHAFT... 10 KITS & ASSEMBLIES... 11 LEVER ASSY... 12
More informationMANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. ASSEMBLY...24 Gear Components...24
MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
More informationCOMPONENTS REAR DIFFERENTIAL COMPONENTS
COMPONENTS REAR DIFFERENTIAL COMPONENTS REMOVAL 1. Drain the differential gear oil. 2. Remove the rear disk brake. 3. Remove the parking brake and cable. 4. Remove the stabilizer bar. 5. Pull out the
More informationIllustrated Parts List
Illustrated Parts List TA-J7-400026 (ETS-2040) August 202 Contents How To Use The Illustrated Parts List... AUXILIARY COUNTERSHAFT ASSEMBLY... 4 AUXILIARY DRIVE GEAR ASSEMBLY... 5 AUXILIARY MAINSHAFT ASSEMBLY...
More information6-speed manual gearbox 0A5
Service Training Self-study programme 320 6-speed manual gearbox 0A5 Design and function S320_002 In addition to meeting increasing technical demands, modern cars also have to represent effective space
More informationG Class Transfer Case. 217 HO 06 Transfer Case (IC GC OP TF)
G Class Transfer Case 217 HO 06 Transfer Case (IC GC OP TF) 1-30-03 2 These technical training materials are current as of the date noted on the materials, and may be revised or updated without notice.
More informationStrain Gauge Gearlever User Manual With Switchbox
Strain Gauge Gearlever User Manual With Switchbox 25.03.0022 Introduction The Strain Gauge Gearlever is specially designed to be used for flat shifting. A strain gauge is an accurate instrument to cut
More information